Sie sind auf Seite 1von 8

How to read welding gauges

Welding gauges are available for checking alignment, checking dimensions before welding, verifying weld dimensions, and checking porosity of welds. Some gauges are multipurpose or single purpose. instructions for WG-1 | WG-2 | WG-3 | WG-4 | WG-5 | WG-6

WG-1 HI-LO Welding Gage measures internal alignment of pipe after fit-up/ alignment. This cuts radiographic rejects. It measures internal misalignment of pipe before and after tacking. Measurements read in inch on one side and metric on the opposite side. The gauge measures internal mismatch of pipe wall, scribe lines, weld fillet and crown height. It satisfies fit-up codes ASME, ANSI, API & Military.

Back to Top of Page

WG-2 Economy Single Purpose HI-LO Welding Gage is designed for internal alignment and determining rootweld spacing. Internal HI-LO gage. Four quick steps check internal alignment You can check the internal alignment of your fit-up quickly with the WG-2 HI-LO Gage. 1. unlock the retaining screws. Press the gage legs beyond the barrel. 2. insert the legs ( wires ) into the root gap space of the two pieces of pipe to be fitted. Turn the gage 90 , being careful to apply a constant back pressure to the barrel.

3. Hold the gage as square as possible with the fitting to obtain an accurate reading. Lock the retaining screw, Reverse the 90 turn and remove the gage. You've now ready to read the increment opposite the red line. 4. When the red line aligns with the 1/32 increment you have a good internal alignment and fit-up. Misalignment can be determined from the zero line by increment markings of 1/16 inch. Rootweld spacing gage. Easy operation determines rootweld spacing. 1. Unlock the retaining screw and insert the gage interior alignment stops between the two pieces of pipe to be fitted. 2. Insert the leg with the long taper into the root gap until it makes contact with both sides of the gap. Relock the retaining screw, remove the gage and read it. 3. The scale is calibrated in fractional dimensions from 1/32 to 3/16 inch in 1/16 inch increment markings. The readout you receive represents the amount of the rootweld gap.

Back to Top of Page

WG-3 adjustable fillet weld gauge with unequal leg measurement feature. This gauge measures any fillet weld from 1/8" to 1" to 1/32" accuracy with just one simple to use gauge. The WG-3 adjustable fillet weld gauge used an offset arm which slides at a 45 angle to make fillet weld length measurement. Simply adjust the arm until it touches the toe of the vertical leg. The gage is calibrated to 32nds. Four screws hold the offset arm in position for future adjustments. This gauge also measures weld throat thickness to 1/16" of an inch by adjusting a pointer in position for future reference. If the weld is concave, more filler material can be added to build the weld throat up to standard. The WG-3 adjustable fillet weld gauge is made of durable, rust resistant stainless steel. Its 2-1/4 x 3" slim design weighs only 1-1/2 Oz. It fits easily into a shirt pocket. Because there is just one gage need to make all measurements, the chance of losing essential fillet weld gage blades is eliminated. Fumbling through seven different gages blades is also eliminated. WG-3 adjustable fillet weld gauge measures both leg lengths and weld throat fillet weld thickness.

Back to Top of Page

WG-4 Weld Gauge or Bridge Cam Gauge is a unique, versatile instrument for the inspection of welded surfaces and joints. It measures angle of preparation, 0 to 60 , excess weld metal ( capping size), depth of undercut, depth of pitting, fillet weld throat size, fillet leg length, misalignment ( high-low), and linear measurements up to 60mm or 2 inches. It measures in both inch or millimeters. It is easy to use. It comprising of one rotating dial and one sliding pointer. Move the dial or pointer until it makes the appropriate contact and then read the result.

Back to Top of Page

WG-5 V-WAC Gage quickly determine if fillet welds meet NRC Visual Weld Acceptance Criteria for structural weldments. It easily and quickly checks the four essential measurements required for compliance with NRC Visual Weld Acceptance Criteria. It checks undercut depth, porosity comparison, amount of porosity per linear inch and crown height. The undercut depth or crown height scale can be read to 1/32 inch.

Porosity comparision of 1/8" and 1/16 inch. Linear gage in 1/16 inch increments. The gage is easy to set and a locking screw holds it in position for later reference. All four required measurements are made with a single gage.

Back to Top of Page

WG-6 A.W.S. Type Gauge. Automatic weld size weld gage for accurate calibrations of butt and fillet type welds. With the WG-6 A.W.S Type Gauge it is possible to meet specifications of butt and fillet type welds. The following diagrams illustrate the ease with which welders and inspectors may accurately check sizes of convex or concave fillets as well as butt weld reinforcements. The convexity and concavity sizes have automatically been determined in accordance with American Welding Society D1.1 Paragraph 3.6. The gauge is built of stainless steel with dimensional readings chemically etched and filled for easier reading.

Back to Top of Page link to welding gage index page

Newman Tools Inc. 185 Iber Road Stittsville, Ottawa, Ontario, Canada K2S 1E7 Phone: 1-613-836- 6776 or 1-800-465-1384 Fax: 1-613 -836 -9070 or 1-800-605-2442

Newman Tools Inc. 151 New Park Avenue Hartford, CT 06106, USA Phone: 1-800-465-1384 Fax: 1-800-605-2442 Email: info@newmantools.com

Das könnte Ihnen auch gefallen