Beruflich Dokumente
Kultur Dokumente
The Y-pattern diaphragm valve, with large seat opening and high lift disc, permits greater ows at lower pressure loss than any comparable valve. Positive control action is achieved, either hydraulically or pneumatically without the aid of springs. Components are serviceable while the valve is in line. These valves are available in both metallic and thermoplastic materials and are ideal for water treatment equipment such as water softeners and media lters.
VALVE OPEN
AIR VENT
LOWER CHAMBER
LINE PRESSURE
FLOW
FEATURES
Durable & Cost effective Extended diaphragm life Low pressure loss through valve Large opening, high lift disc gives high ow rates Positive closing and opening Hydraulic or pneumatic operation Diaphragm replaceable without interruption of ow Adaptable to many control devices
Full Open Operation When closing pressure, in upper chamber, is relieved by venting the pilot line, the valve opens, positively, by line pressure on the disc.
ON/OFF CONTROL NO PRESSURE
VALVE CLOSED
AIR VENT
UPPER CHAMBER
OPTIONS
Flow Limit Stops Spring-Assist. Open Spring-Assist. Closed Normally Closed Position Indication
LINE PRESSURE
Drip-Tight Closing Closure is obtained by directing line pressure or equivilent independent pressure into the upper chamber. This pressure on the large diaphragm area causes the valve
FLOW RATES
Y-pattern design, large seat opening and high-lift diaphragm produce excellent ow characteristics. There are no springs and related parts to consume space or restrict ow. The diaphragm is shape-formed of Buna N on Nylon to assure long life. It can be replaced without stopping ow, and all parts can be serviced with the valve in line. Valves are available with cast iron and brass. Maximum operating pressure: 125 psi (860 kPa); Minimum operating pressure: 7 psi (48 kPa); Maximum temperature: 300o F. (148o C). For versatillity of application, valves are available to be either opened or closed by pilot pressure.
1
50 40 35 30
FLOW RATES - DIAPHRAGM VALVES (METALLIC) CONTINUOUS FLOW 20 FEET PER SECOND INTERMITTENT FLOW 30 FEET PER SECOND
4 42 5
25 20
42
42
42
42
42
15
10 9 8 7 6 5
/2
21
3/4
11
/2
11
/4
42
2 0 0 0 3 0 0 0 4 0 0 0
1 0
1 5
2 0
2 5
3 0
4 0
5 0
6 7 8 9 1 0 0 0 0 0 0
2 0 0
3 0 0
4 0 0
5 0 0
6 0 0
7 0 0
8 9 1 0 0 0 0 0 0 0
LITERS PER MIN. = G.P.M. X 3.78 FLOW RATES FOR PLASTIC VALVES - SEE BULLETIN #802
DIMENSIONS
D
Size w-1
AT
In. 3n 94 4w
AF
BT
44 108 5a 136 7.25 184 8 203 9w 247
BF
CT
34 82 4 101 5.376 136 5w 146 6w 171
CF
D
2w 70 32 89 4.875 123 68 155 74 184
14-12 THRD
CF BT (THREADED) BF (FLANGED) F CT
mm. 120 In. 6.62 mm. 168 In. 7a mm. 187 In. 9 mm. 228 In. mm. In. mm. In. mm. 10s 270 11w 298 17 431
THRD
E AT (THREADED) AF (FLANGED)
w 18 w 18 d 20
4-F 6-F
SPECIFICATIONS
Sizes: w"3" Threaded / 3"6" Flanged Class: 125 Pound Pressure: 125 PSI recommended Working Pressure (860 kPa). Temperature: Water-Air Standard 32oF150oF (0oC65oC) High Temperature 150oF300oF (65oC148oC) Materials: Body & Cap Cast Iron or Bronze (consult factory for thermoplastic valves) Trim Bronze with Stainless Steel Shaft Diaphragm Standard: Buna N / Nylon High Temperature: EPDM/Nomex Seals Standard High Temperature Static: Buna N EPDM Dynamic: Buna N EPDM
5356 Hillside Avenue Indianapolis, IN 46220 P: +1 888-56-Water (569-2837) F: +1 317-255-4727 info@nancrede.com www.nancrede.com
1-181