Beruflich Dokumente
Kultur Dokumente
A. Nombre y direccin de la obra. B. Fecha de la recepcin de las muestras y fecha de los ensayos. C. Fabricante y norma NTC bajo la cual se fabric el material y bajo la cual se realizaron los ensayos. D. Peso por unidad de longitud de la barra, alambre, malla o torn de refuerzo, y su conformidad con las variaciones permitidas y su dimetro nominal.
E. Caractersticas del corrugado, cuando se trate de acero corrugado. F. Resultados del ensayo de traccin, los cuales deben incluir: la resistencia a la fluencia y la resistencia ltima evaluadas, utilizando el rea nominal de la barra, alambre malla o torn de refuerzo indicada en la norma NTC correspondiente, y el porcentaje de alargamiento obtenido del ensayo.
PROPIEDADES FISICAS
DIAMETRO. AREA DE LA SECCION. PESO POR UNIDAD DE LONGIUD.
W real = PESO DE LA BARRA L = LONGITUD DE LA BARRA
ENSAYO DE TENSION
SE UTILIZA PARA MEDIR LAS SIGUIENTES PROPIEDADES:
Resistencia a la fluencia. Resistencia ultima. Porcentaje de elongacin.
ELONGACION MAXIMA
max
(%) = Lu Lo Lo
x 100
ENSAYOS DE DOBLADO
La barra se coloca de tal manera que las venas longitudinales no queden en la cara exterior.
GANCHO ESTANDAR
El trmino gancho estndar, tal como se usa en el Titulo C de la norma significa: a). Un doblez de 180 ms una extensin recta de longitud mnima igual a 4db pero no menor de 6.5 cm en el extremo de la barra. b). Un doblez de 90 ms una extensin de longitud mnima igual a 12 db en el extremo de la barra.
GANCHO ESTANDAR
GANCHO ESTANDAR
REQUISITOS ESENCIALES
COEFICIENTE DE MODIFICACION
=
coeficiente relacionado con la localizacin de la barra.
( = 1.3 , 1.0)
= =
coeficiente relacionado con el tipo de superficie del refuerzo. ( = 1.5 , 1.2, 1.0)
= 1.5 = 1.2
= 1.0
El producto no hay necesidad que exceda 1.7 = relacionado con el dimetro de la barra
l =
db
db fy
200 mm
4 fc
EMPALMES A TRACCION
EMPALME CLASE A: 1.0 d EMPALME CLASE B: 1.3 ld
Donde
ld
es
la
longitud
de
desarrollo
traccin
para
el
fy
correspondiente y sin coeficiente de modificacin. La longitud mnima de traslapo no debe ser menor de 30 cm.
0.007 fy db >30 cm
Para fy= 4.200 kgf/cm o menos. Para fc menores de 211 kgf/cm la longitud de traslapo debe incrementarse en un tercio
REQUISITOS ESENCIALES
__
d
__
FORMALETAS
FORMALETAS
Para Edificios de Tamao y Altura Limitados Basado en ACI 318-02 (2002) AIS - ICONTEC - ACI
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
RECUBRIMIENTOS IGUALES ? ?
RECUBRIMIENTOS MNIMOS ? ?
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES
REQUISITOS ESENCIALES