Beruflich Dokumente
Kultur Dokumente
TS2- 6 2 05 ZZ C3 P5
Bore diameter number Internal modification code Cage codes Supplementary suffix code Seal/shield code Ring configuration code Duplex arrangement code Tolerance code Lubrication code
Table 2.2 Supplementary prefix code code FTS2TS3TS4TMCSESECACDefinition Staainless steel bearings Dimension stabilized bearings for high temperature use (to 160C) Dimension stabilized bearings for high temperature use (to 200C) Dimension stabilized bearings for high temperature use (to 250C) Special heat treated long-life bearings Special heat treated long-life bearings Special heat treated and material extra long-life bearings Expansion compensating bearings Creep preventing bearings 1
Table 2.3 Bearing series symbol Dimensions series Bearing series Type symbol width series (1) (1) 6 (1) (0) (0) (0) diameter Bearing type series 8 9 0 2 3 4 Single row deep groove ball bearings
68 69 60 62 63 64
Note: Please consult TPI concerning bearing series codes, and supplementary prefix/suffix codes not listed in the above table.
Table 2.4 Bore diameter number Bore diameter Bore diameter number /0.6 /1.5 /2.5 1 9 00 01 02 03 /22 /28 /32 04 05 06 07 08 09 10 d mm 0.6 1.5 2.5 1 9 10 12 15 ____ Slash ( / ) before bore diameter number Bore diameter expressed in single digits without code Remark
Table 2.5 Supplementary suffix number Code L1 F1 G1 Cage Seal or shield configuration G2 J T1 T2 LLB LLU LLH ZZ ZZA N Ring NR D C2 (CN) C3 Explanation Machined brass cage Machined steel cage Machined brass cage, rivetless Pin-type steel cage Pressed steel cage Phenolic cage Plastic cage, nylon or teflon Synthetic rubber seal (non-contact type) Synthetic rubber seal (contact type) Synthetic rubber seal (low torque type) Shield Removable shield Snap ring groove on outer ring, but without snap ring Snap ring on outer ring Bearings with oil holes Radial internal clearance less that Normal Normal radial internal clearance but not shown in nominal numbers Radial internal clearance less that Normal Radial internal clearance less that C3 Radial internal clearance for electric motor bearings Non-interchangeable clearance (shown after clearance code) Light preload Normal preload Medium preload Heavy preload JIS standard Class 6 JIS standard Class 5 JIS standard Class 4 JIS standard Class 2 Shell Alvania S2 grease Caltex RPM SRI 2 grease ESSO Beacon 325 grease MULTEMP SRL grease
17 22 28 32 20 25 30 35 40 45 50 Bore diameter number in double digits after dividing bore diameter by 5 Slash ( / ) before bore diameter number
Table 2.6 Number and code arrangement for angular contact ball bearings(ACBB) Code Ball material Ring material 5Sblank Fblank 7 Bearing series Basic Numbers Supplementary suffix code HSE BST 5 9 Diameter series 0 2 Bore diameter number 8 : 20 C Contact angle code CE1 AD (A) B Cage T1 blank DB DF Matching code DT DBT DTBT Flush grinding G blank /GL Internal clearance /GN /GM /Gxx /CSxx P5 P4 Tolerance standard P4X P42 P2 Refer to Table 2.4, BSTs code is bore diameter(mm) x outside diameter(mm) 15o 18o 25o 30o,may not shown in code 40o Phenolic cage Nylon cage Back to back(double-row) Face to face(double-row) Tandem(double-row) Tandem and back to back (triple-row) Tandem and back to back(quad-row) Flush ground type Without flush ground Light preload Normal preload Medium preload Special preload Special clearance JIS standard Class 5 JIS standard Class 4 JIS standard Class 4 special bore and outside diameter tolerance JIS standard Class 4 (dimensional) JIS standard Class 2 (running accuracy) JIS standard Class 2 Refer to Table 2.3, BSTcode is blank Explanation Si3N4 Ceramic balls SUJ2 SUS440C SUJ2 Standard type ACBB High speed type ACBB Thrust ACBB(60o Contact angle) Double row ACBB
5S-7014C T1 DB G /GL P4