Beruflich Dokumente
Kultur Dokumente
cz
MC A REGULAN TECHNIKA
info@thermis.cz
The cock body is made of a rod, the cone is fitted from below with a nut. The pressure gauge cock is a fitting used to close the working medium flow.
Body, cone Sleeve connection Grip brass steel, surface treated plastic material
Material:
DIN 16 263
The cock body is made of a rod, the cone is fitted from below with a nut. The pressure gauge cock is a fitting used to close the working medium flow. The side outlet with the flange is used to connect the testing pressure gauge or to deaerate the pressure gauge and to blow through the connection. The pressure gauge cock may be mounted in any position.
Body, cone Sleeve connection Nut Grip brass steel, surface treated steel, surface treated plastic material
Material:
www. thermis.cz
MC A REGULAN TECHNIKA
info@thermis.cz
DIN 16 260
d M 12 x 1,5 G 1/4 " d1 M 12 x 1,5 LEFT D 3 3 L 55 55 L1 55 55 V 41 41 S 17 17 kg 0,15 0,15
DIN 16 262
d M 20 x 1,5 G 1/2 " d1 M 20 x 1,5 LEFT D 3 3 L 80 80 L1 70 70 V 56 56 S 27 27 kg 0,4 0,4
DIN 16 263
DIN 16 263
d M 20 x 1,5 G 1/2 " d1 M 20 x 1,5 LEFT D 3 3 L 80 80 L1 70 70 L2 35,5 35,5 V 56 56 S 27 27 kg 0,45 0,45
www. thermis.cz
MC A REGULAN TECHNIKA
info@thermis.cz
To connect the pressure gauge and the testing pressure gauge with a flat sealing. The valve is not fit for regulation. It is made in four material designs. The pressure gauge cock is a fitting used to close the working medium flow. The body is a forging. After the valve has been closed, the venting screw is used to discharge the working medium between the valve and the pressure gauge. If any untightness occurs in the course of the valve operation, the nut of the gland shoul be tightened or the gland sealing added or replaced. The sealing of the spindle is asbestosfree. The valve may be mounted in any position. The valve is tested in accordance with SN 13 3060, part 2. Material:
Sleeve connection Spindle Hand Wheel in the table stainless steel plastic material
SN 13 75 17.A SN 13 75 17.B
Pressure (MPa) 25 63 63 63 SN 13 7517.5 SN 13 7518.5 SN 13 7517.3 SN 13 7518.3 SN 13 7517.4 SN 13 7518.4 SN 13 7517.2 SN 13 7518.2
Material brass 42 3223 brass 42 3223 stainless steel 17 027.6 stainless steel 17 027.6 stainless austenitic steel 17 246.4 stainless austenitic steel 17 246.4 structural alloy steel 15 128.5 structural alloy steel 15 128.5
www. thermis.cz
MC A REGULAN TECHNIKA
info@thermis.cz
d M 20 x 1,5
d1 M 20 x 1,5 LEFT
D 3
L 85
V 100
z 4
S 27
Dk 80
kg 0,85
www. thermis.cz
MC A REGULAN TECHNIKA
info@thermis.cz
CONDENSATION LOOP
SN 13 75 30 PN 250
To connect and protect pressure gauges against harmful effects of high temperature of the working medium measured. Suitability of the material design depending on working medium must be consulted with the manufacturer. If the operation is interrupted in winter months, the loop must be discharged or filled with non-freezing liquid. The valve is tested in accordance with SN 13 3060, part 2, or with DIN 3230, part 3, only with water for tightness. The loop may be mounted in any position.
SN 13 75 30.A Condensation gooseneck loop with pin SN 13 75 30.B Welding condensation gooseneck loop SN 13 75 30.C Coiled condensation loop with pin SN 13 75 30.D Coiled welding condensation loop
Teplota (C) 400 Tlak (MPa) 25 Materil SN 13 753x.1 structural carbon steel 11 523 SN 13 753x.3 stainless steel 17 027
SN 13 75 30.A+B
d M 20x1,5 d1 M 20x1,5 LEFT L 225 d3 6 D 3 V 170 V1 130 l 22 l2 5 DTR 20 t 2,5 A 45 kg 0,65
SN 13 75 30.C+D
d M 20x1,5 d1 M 20x1,5 LEFT d3 6 D 3 V 240 l 22 l2 5 DTR 20 t 2,5 k 56 kg 0,7
www. thermis.cz
MC A REGULAN TECHNIKA
info@thermis.cz
L1 18
I 15
I1 16
I2 6
Omax S kg 2 27 0,09
M 12x1,5 inside/ G 1/4" outside G 1/4" inside/ M 12x1,5 outside M 20x1,5 inside/ G 1/2" outside G 1/2" inside/ M 20x1,5 outside
d d1 M20x1,5 G 1/2" d2 7 d3 D L I I1 I2 I3 S kg 6 3,5 40 19 18 6 5 27 0,09
d M20x1,5
d1 G 1/2"
d2 7
L 40
I 19
I2 16
S 27
kg 0,09
L 20 36
L1 10 18
I1 7,5 16
I2 5 5
Omax 2 2
S 17 27
kg 0,03 0,09
Welding nipple: 13 75 24.C M 12x1,5 M 20x1,5 Cap nut: 13 75 24.B M 12x1,5 M 20x1,5 Welding adapter: 13 75 24.D M 12x1,5 M 20x1,5
6 Churho 1, 618 00 Brno, Czech Republic
d M 12x1,5 LEFT M 20x1,5 LEFT d1 12 20 D 6 7 L 50 80 I 12 20 z 1,5 1,5 z1 3 4 h 2 3 kg 0,04 0,16 d M 12x1,5 M 20x1,5 d1 12,5 20,5 d2 6,5 12,5 L 21 30 I 17 24 I2 3 3 S 17 27 kg 0,03 0,08 Size 12 20 d 9,5 17,5 d2 5,5 7 d3 6 12 D 3 3,5 L 25 35 I1 6 5 I2 4 6 z 1,5 1,5 kg 0,01 0,03