Beruflich Dokumente
Kultur Dokumente
InFocus Projectors
R
Models: SP-CEIL-011
This product is intended for use with UL Listed products and must be installed by a qualified professional installer.
Read instruction sheet before you start installation and assembly. Installer must verify that the ceiling will safely support
SET SCREW
1 of 7
Visit the InFocus Web Site at www.infocus.com
Before you start check the parts list to insure all of the parts shown are included.
Parts List
Description A B C D E F G H I J K L M N O P ball and socket mount 4 mm security allen wrench M5 x .8 x 10 mm socket pin type F screw #10-32 x 3/8 spade thumb screw #10-32 x 3/8 serrated washer head socket pin screw #14 x 2.5 phillips hex head wood screw ceiling plate .25" ID x .56" OD x .26 spacer extension column connector 10-32 x 3/8 socket pin screw 10-32 x 3/16 slotted set screw adapter plate M4 x 16 mm serrated washer head socket pin screw M4 x 12 mm serrated washer head socket pin screw .198 x .313 x .375 retaining spacer .198 x .313 x .187 retaining spacer Qty. 1 1 1 1 1 2 1 2 1 2 1 1 3 1 3 1 Part Number 055-0011 560-9646 520-1164 560-1107 520-1151 5S1-015-C03 580-1042 590-1050 580-1013 520-1084 520-1187 055-1445 510-1087 510-1079 590-2020 590-1030
C A I M
J N K
E D
H O P
G .ASTENERS
2 of 7
Visit the InFocus Web Site at www.infocus.com
NOTCH
Skip to step 5.
WOOD JOIST
C A G
CEILING
G
DETAIL 1
A Installation To Wood Joist .inished Ceilings, Exposed Wood Joists, WOOD or Wood Beam Ceilings JOIST
Drill two 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach ceiling plate (G) with two #14 x 2.5" (6 mm x 65 mm) wood screws (F) as shown using 3/8" (10 mm) socket wrench. Tighten wood screws (F) so ceiling plate (G) is firmly attached. DO NOT TIGHTEN WITH EXCESSIVE FORCE! Over-tightening can cause stress damage to wood screws (F) greatly reducing their holding power! Tighten to 80 in lb (9 N.M.) maximum torque. Skip to step 5. WARNING: It is the responsibility of the installer to verify that the ceiling will safely support the combined load of all attached hardware and components. IMPORTANT: Be sure to drill holes into the joist CENTER!
CEILING
F F
For Optional Cord Management, install two spacers (H) between ceiling plate (G) and ceiling.
3 of 7
CONCRETE CEILING
G
1
concrete ceiling
concrete anchor
F
Illustration A
FOR DIRECT ATTACHMENT TO LOAD BEARING CONCRETE ONLY! Concrete expansion anchors are not intended for attachment to concrete ceilings covered with a layer of plaster, drywall, or other finishing material. If mounting to concrete ceiling covered with plaster / drywall is unavoidable, plaster / drywall must be counterbored as shown below.
INCORRECT
CUTAWAY VIEW
metal bracket concrete metal bracket
G F
concrete anchor
CORRECT
concrete
concrete anchor
4 of 7
Visit the InFocus Web Site at www.infocus.com
C G
EXTENSION COLUMN
SLOT
DETAIL 3
EXTENSION COLUMN
I
SLOT
SLOT
I J
DETAIL 4
EXTENSION COLUMN
I K A
SLOT
J
DETAIL 6
5 of 7
Visit the InFocus Web Site at www.infocus.com
Flip projector upside down. Find your projector from the models listed below. Using the holes indicated on the corresponding hole pattern diagram, attach adapter plate (L) to projector using three M4 x 16 mm serrated washer head socket pin screws (M) and three .198 x .313 x .375 retaining spacers (O). Notes: Retaining spacers go between adapter plate and projector. * Notch indicates front of projector. ** Projectors using hole pattern G use one M4 x 12 mm screw (N) and one .198 x .313 x .187 retaining spacer (P) where indicated. A. C200, C420, DP6500X, DP8200X, LP650, LP820, SP7200, SP7205 B. C40, C50, DP2000S/X, LP240, LP250 C. LP340, LP350, LP500, LP530, SP110
F. C170, LP600
**
6 of 7
Visit the InFocus Web Site at www.infocus.com
Note: The projector you are installing may differ in appearance from the sample illustrated below. Attach projector to the ball and socket mount (A) by inserting the ball and socket mount (A) into the adapter plate connection and twisting until the adapter plate will no longer turn (about 75). The spring loaded captive screw should line up with a corresponding hole on the adapter plate (this should line up automatically when the two are connected). Push down and tighten the spring loaded captive screw to secure the adapter plate to the mount. If not using the optional security feature, fasten thumb screw (D) in the hole opposite the spring loaded captive screw. OPTIONAL: For Armor Lock security, insert serrated washer head socket pin security screw (E) in the hole opposite the spring loaded captive screw. Tighten with security allen wrench (B). This will prevent the projector from being removed. Note: Be sure to only use the 10-32 x 3/8" screw (E) (or the thumb screw (D)) opposite the spring loaded captive screw. To adjust roll, pitch, and yaw loosen the set screw (shown below) using security allen wrench (B) or standard 4 mm allen wrench. You should be able to just slightly loosen the screw so that your adjustments can be set without having to hold the projector. Move projector to desired position and slowly tighten set screw. Note: Be sure not to touch the projector while tightening the set screw. This may cause the image to be unaligned when you let go. IMPORTANT: Allen wrench is your key for projector removal. Store it in a safe place.
WOOD JOIST
CEILING CEILING
E
WOOD JOIST CAPTIVE SCREW
SET SCREW
D
PROJECTOR
2 1
PROJECTOR ADAPTER PLATE
PROJECTOR
WARNING: Do not lift more weight than you can handle! Use additional man power or mechanical lifting equipment to safely handle placement of the projector! 7 of 7
Visit the InFocus Web Site at www.infocus.com
2004 Peerless Industries, Inc. All rights reserved. Peerless is a registered trademark and Armor Lock is a trademark of Peerless Industries Inc. All other brand and product names are trademarks or registered trademarks of their respective owners.