Beruflich Dokumente
Kultur Dokumente
Orbitco-CCNA-Pastquestions.com
Helping You Pass Your CCNA Exams
Home
Contact Us
Home
Note: This RIP v2 LAB are used for demonstration only, you will see different IP addressing, VLAN configuration and Port allocation in the real CCNA exam. But it all works the same way if you could just grasp the technique. I suggest you use packet tracer for practice. Download Cisco Packet tracer here
Ques t ion: To configure the router (R2-RC) click on the console host icon that is connected to a router by a serial console cable (shown in the diagram as a dashed black line) Central Florida Widgets recently installed a new router in their office. Complete the network installation by performing the initial router configurations and configuring RIPV2 routing using the router command line interface (CLI) on the R2-RC. Router configuration: Name of the router is R2-RC Enable-secret password is c is c o1 The password to access user EXEC mode using the console is c is c o2 The password to allow telnet access to the router is c is c o3 IPV4 addresses must be configured as follows: Ethernet network 209. 165. 202. 128/ 27 - router has last assignable host address in subnet Serial network is 192.0.2.16/28- router has last assignable host address in the subnet. Interfaces should be enabled. Router protocol is RIPV2
* required
First Name: *
Email Address: *
Sign Me Up
Email Marketing by VerticalResponse
www.orbitco-ccna-pastquestions.com/CCNA-RIPv2-Configuration-Simulation-Exam.php
1/3
9/11/13
S olut ion: 1. Conf igure rout er name: Router>enable Router#configure terminal Router(config)#hostname R2-RC 2. Conf igure s ec ret pas s word: R2-RC(config)# enable secret cisco1 3) Conf igure c ons ole P as s word: R2-RC(config)#line console 0 R2-RC(config-line)#password cisco2 R2-RC(config-line)#login R2-RC(config-line)#exit 4) Conf igure Telnet pas s word: R2-RC(config)#line vty 0 4 R2-RC(config-line)#password cisco3 R2-RC(config-line)#login R2-RC(config-line)#exit 5) A s s ign IP addres s f or E t hernet int erf ac e(Fa0/ 0): I will advise you to try and know or cram this table below; you might be given an opportunity to write it down before the exam:
64
32 3
16 4
8 5
4 6
2 7 8
192 /26
The Ethernet network 209.165.202.128/27: looking at the table above, you can see that the /27 has a bit value of 32 (increment) and mask should be 224 or /27 That means : Net work addres s : 209. 165. 202. 128 S ubnet mas k : 255. 255. 255. 224 B roadc as t addres s : 209.165.202.159 (because 128 + 32 - 1 = 159) Therefore, according to the question; the last assignable host address in this subnet should be: 209.165.202.158. Assign it to fa0/0 using these commands: R2-RC(config)# interface fa0/0 R2-RC(config-if)#ip address 209.165.202.158 255.255.255.224 R2-RC(config-if)#no shutdown R2-RC(config-if)#exit 6) Assign IP address for Serial interface(S0/0/0): (follow the same above) Serial network 192. 0. 2. 16 / 28 Looking at the table above, you can see that the / 28 has a bit value of 16 (increment) and mask should be 240 or / 28 That means : Serial network 192. 0. 2. 16
www.orbitco-ccna-pastquestions.com/CCNA-RIPv2-Configuration-Simulation-Exam.php
2/3
9/11/13
B roadc as t addres s :192. 0. 2. 31 (because 16 + 16 - 1 = 31) According to the question the last assignable host address in this subnet is 192. 0. 2. 30 . Assign it to s0/0/0 interface using the following command: R2-RC(config)# int erf ac e s 0/ 0/ 0 R2-RC(config-if)#ip addres s 192. 0. 2. 30 255. 255. 255. 240 R2-RC(config-if)#no s hut down R2-RC(config-if)#ex it 7) Conf igure RIP v 2 rout ing prot oc ol us ing t he f ollowing c ommand: R2-RC(config)#rout er rip R2-RC(config-router)#v ers ion 2 R2-RC(config-router)#net work 209. 165. 202. 128 R2-RC(config-router)#net work 192. 0. 2. 16 R2-RC(config-router)#end R2-RC#c opy running-c onf igs t art up-c onf ig (dont forget this bit)
Tw eet
619
Copyright 2012. Orbitco-Computer-Solutions.Com. All rights reserved. PrivacyPolicy Contact Us The inform ation provide d on this we bsite is for inform ational purpose s only. orbitco-ccna-pastque stions.com m ak e s no warrantie s, e ithe r e x pre sse d or im plie d, with re spe ct to any inform ation containe d on this we bsite . orbitco-ccna-pastquestions.com reserves the right to change this policy at anytime without prior notice. Ci sco and All related product mentioned in any portion of this website are the registered trademarks of Ci sco . co m and their respective owners
www.orbitco-ccna-pastquestions.com/CCNA-RIPv2-Configuration-Simulation-Exam.php
3/3