Beruflich Dokumente
Kultur Dokumente
Product Specification
Title
BUYER MODEL LGE -
*When you obtain standard approval, please use the above model name without suffix
APPROVED BY /
SIGNATURE DATE
SIGNATURE DATE
REVIEWED BY / W. S. Ha / Manager
Please return 1 copy for your confirmation with your signature and comments.
Ver. 1.1
1 / 29
Product Specification
CONTENTS
Number
COVER CONTENTS RECORD OF REVISIONS 1 2 3 3-1 3-2 3-3 3-4 3-5 3-6 4 5 6 7 7-1 7-2 8 8-1 8-2 9 9-1 9-2 9-3 9-4 9-5 9-6 GENERAL DESCRIPTION ABSOLUTE MAXIMUM RATINGS ELECTRICAL SPECIFICATIONS ELECTRICAL CHARACTERISTICS INTERFACE CONNECTIONS SIGNAL TIMING SPECIFICATIONS SIGNAL TIMING WAVEFORMS COLOR INPUT DATA REFERENCE POWER SEQUENCE OPTICAL SPECIFICATIONS MECHANICAL CHARACTERISTICS RELIABILITY INTERNATIONAL STANDARDS SAFETY EMC PACKING DESIGNATION OF LOT MARK PACKING FORM PRECAUTIONS MOUNTING PRECAUTIONS OPERATING PRECAUTIONS ELECTROSTATIC DISCHARGE CONTROL PRECAUTIONS FOR STRONG LIGHT EXPOSURE STORAGE HANDLING PRECAUTIONS FOR PROTECTION FILM
ITEM
Page
1 2 3 4 5 6 6 8 12 13 14 15 17 21 24 25 25 25 26 26 26 27 27 27 28 28 28 28
Ver. 1.1
2 / 29
Product Specification
RECORD OF REVISIONS
Revision No
1.0 1.1
Revision Date
Dec. 17, 2004 Jan. 04 .2005
Page
23 Final Lead Free is applied
Description
Ver. 1.1
3 / 29
Product Specification
1. General Description
LC171W03 is a Color Active Matrix Liquid Crystal Display with an integral Cold Cathode Fluorescent Lamp(CCFL) backlight system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally black mode. It has a 17.1 inch diagonally measured active display area with WXGA resolution (768 vertical by 1280 horizontal pixel array) Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot, thus, a palette of more than 16,7M(true) colors. It has been designed to apply the 8 bit LVDS interface. It is intended to support LCD TV, PCTV where high brightness, wide viewing angle, high color saturation, and high color are important.
RGB(Mini-LVDS) LVDS 5pair (20pin) VLCD +12.0V
CN1
General Features
Active Screen Size Outline Dimension Pixel Pitch Pixel Format Color Depth Luminance, White Viewing Angle (CR>10) Power Consumption Weight Display Operating Mode Surface Treatment Ver. 1.1 17.1 inches(434.38mm) diagonal 400.0(H) x 258.0(V) x 22.0(D) mm(Typ.) 0.291mm x 0.291mm 1280 horiz. By 768 vert. Pixels RGB stripe arrangement 8-bits, 16,7M colors 450 cd/m2 (Center 1 point (Typ.)) Viewing Angle Free [R/L 176( Typ.), U/D 176(Typ.)] Total 31.1 Watt(Typ.), ( 2.9 Watt@VLCD, 28.2 Watt@450cd/[LAMP=7mA]) 2,500 g (Typ.) , 2,650 g (Max) Transmissive mode, normally black Hard coating(3H) & Anti-glare treatment of the front polarizer Jan. 04, 2005 4 / 29
Product Specification
Power Input Voltage Operating Temperature Storage Temperature Operating Ambient Humidity Storage Humidity
C C
Note 1 %RH %RH
Note : 1. Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39 C Max, and no condensation of water.
Ver. 1.1
5 / 29
Product Specification
Parameter
Symbol
Unit
Notes
Note : 1. The specified current and power consumption are under the VLCD=12.0V, 25 2C,fV=60Hz condition whereas mosaic pattern(8 x 6) is displayed and fV is the frame frequency. 2. The current is specified at the maximum current pattern. 3. The duration of rush current is about 2ms and rising time of power Input is 1ms(min.).
Mosaic Pattern(8 x 6)
Ver. 1.1
6 / 29
Product Specification
Table 2-2. ELECTRICAL CHARACTERISTICS
Values Min LAMP : Operating Voltage Operating Current Established Starting Voltage VBL IBL Vs 1,030 1,340 fBL Ts PBL 50,000 28.20 45 60 80 3 31.10 VRMS VRMS kHz Min Watt Hrs 4 1, 5 6 1, 7 660(7.5mA) 3.0 670(7mA) 7.0 770(3mA) 7.5 VRMS mARMS 1, 2 1 1, 3 Typ Max
Parameter
Symbol
Unit
Notes
Note : The design of the inverter must have specifications for the lamp in LCD Assembly. The performance of the Lamp in LCM, for example life time or brightness, is extremely influenced by the characteristics of the DC-AC inverter. So all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. When you design or order the inverter, please make sure unwanted lighting caused by the mismatch of the lamp and the inverter (no lighting, flicker, etc) never occurs. When you confirm it, the LCD Assembly should be operated in the same condition as installed in you instrument. Do not attach a conducting tape to lamp connecting wire. If the lamp wire attach to a conducting tape, TFT-LCD Module has a low luminance and the inverter has abnormal action.Because leakage current is occurred between lamp wire and conducting tape. 1. Specified values are for a single lamp. 2. Operating voltage is measured at 25 2C. The variance of the voltage is 10%. 3. The voltage above VS should be applied to the lamps for more than 1 second for start-up. (Inverter open voltage must be more than lamp starting voltage.) Otherwise, the lamps may not be turned on. The used lamp current is the lamp typical current. 4. Lamp frequency may produce interface with horizontal synchronous frequency and as a result this may cause beat on the display. Therefore lamp frequency shall be as away possible from the horizontal synchronous frequency and from its harmonics in order to prevent interference. 5. Lets define the brightness of the lamp after being lighted for 5 minutes as 100%. TS is the time required for the brightness of the center of the lamp to be not less than 95%. 6. The lamp power consumption shown above does not include loss of external inverter. The used lamp current is the lamp typical current. (PBL = VBL x IBL x NLamp ) 7. The life is determined as the time at which brightness of the lamp is 50% compared to that of initial value at the typical lamp current on condition of continuous operating at 25 2C.
Ver. 1.1
7 / 29
Product Specification
8. The output of the inverter must have symmetrical(negative and positive) voltage waveform and symmetrical current waveform (Unsymmetrical ratio is less than 10%). Please do not use the inverter which has unsymmetrical voltage and unsymmetrical current and spike wave. Requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp, are following. It shall help increase the lamp lifetime and reduce leakage current. a. The asymmetry rate of the inverter waveform should be less than 10%. b. The distortion rate of the waveform should be within 2 10%. * Inverter output waveform had better be more similar to ideal sine wave. * Asymmetry rate: Ip | I p I p | / Irms x 100% * Distortion rate I p (or I p) / Irms
I -p
9. The inverter which is combined with this LCM, is highly recommended to connect coupling(ballast) condenser at the high voltage output side. When you use the inverter which has not coupling(ballast) condenser, it may cause abnormal lamp lighting because of biased mercury as time goes. 10.In case of edgy type back light with over 4 parallel lamps, input current and voltage wave form should be synchronized
Ver. 1.1
8 / 29
Product Specification
Note:
1. 20th Pin should be ground. 2. All GND(ground) pins should be connected together and to Vss which should also be connected to the LCDs metal frame. 3. All VLCD (power input) pins should be connected together. 4. Input Level of LVDS signal is based on the IEA 664 Standard. Rear view of LCM 1 20
GT123-20P-H16(LG)
Ver. 1.1
9 / 29
Product Specification
Table 4. REQUIRED SIGNAL ASSIGNMENT FOR LVDS Transmitter (DS90C385 or Compatible)
Pin # Pin Name TxIN0 TxIN1 TxIN2 TxIN3 TxIN4 TxIN5 TxIN6 TxIN7 TxIN8 TxIN9 TxIN10 TxIN11 TxIN12 TxIN13 TxIN14 TxIN15 TxIN16 TxIN17 TxIN18 TxIN19 TxIN20 TxIN21 TxIN22 TxIN23 TxIN24 TxIN25 TxIN26 TxIN27 Symbol Red0 [LSB] Red1 Red2 Red3 Red4 Red7 [MSB] Red5 Green0 [LSB] Green1 Green2 Green6 Green7 [MSB] Green3 Green4 Green5 Blue0 [LSB] Blue6 Blue7 [MSB] Blue1 Blue2 Blue3 Blue4 Blue5 RES Description Red Pixel Data Red Pixel Data Red Pixel Data Red Pixel Data Red Pixel Data Red Pixel Data Red Pixel Data Green Pixel Data Green Pixel Data Green Pixel Data Green Pixel Data Green Pixel Data Green Pixel Data Green Pixel Data Green Pixel Data Blue Pixel Data Blue Pixel Data Blue Pixel Data Blue Pixel Data Blue Pixel Data Blue Pixel Data Blue Pixel Data Blue Pixel Data Rx3Rx3+ No connection, If unnecessary No connection, If unnecessary Data Enable Red Pixel Data Rx3Rx3+ Rx2Rx2+ Rx2Rx2+ Rx3Rx3+ Rx1Rx1+ Rx1Rx1+ Rx3Rx3+ Rx0Rx0+ Rx1Rx1+ Rx3Rx3+ Rx0Rx0+ Output
51 52 54 55 56 2 3 4 6 7 8 10 11 12 14 15 16 18 19 20 22 23 24 25 27 28 30 50
Notes : 1. Refer to LVDS Transmitter Data Sheet for detail descriptions. 2. 7 means MSB and 0 means LSB at R,G,B pixel data.
Ver. 1.1
10 / 29
Product Specification
DS90C385
or Compatible TxOUT0TxOUT0+ 48 47
GT123-20P-H16
5 6 100
Timing Controller
RxIN0RxIN0+
TxOUT1TxOUT1+
46 45
8 9
100
RxIN1RxIN1+
TxOUT2TxOUT2+
42 41
11 12
100
RxIN2RxIN2+
TxCLKOUTTxCLKOUT+
40 39
14 15
100
RxCLKINRxCLKIN+
TxOUT3TxOUT3+
38 37
17 18
100
RxIN3RxIN3+
LCD Module
Note: 1. The LCD Module uses a 100 Ohm [] resistor between positive and negative lines of each receiver input. 2. Refer to LVDS Transmitter Data Sheet for detail descriptions. (DS90C385 or Compatible) 3. 7 means MSB and 0 means LSB at R,G,B pixel data.
Ver. 1.1
11 / 29
Product Specification
Table 6. BACKLIGHT CONNECTOR PIN CONFIGURATION(CN2,CN3,CN4,CN5) The backlight interface connector is a model PHR-3(CN3/CN4) and BHR-03VS-1(CN2/CN5) manufactured by JST. The mating connector part number are S 3B-PH-KL (3pin), SM03(4.0)B-BHS-1-TB (3pin) or equivalent. The pin configuration for the connector is shown in the table below.
No Pin 1 CN2 2 3 1 CN3 2 3 1 CN4 2 3 1 CN5 2 3 Symbol H1 H2 H3 L1 L2 L3 L4 L5 L6 H4 H5 H6 Description Power supply for lamp 1(High voltage side) White Notes 1 1 1 2 2 2 2 2 2 1 1 1
Power supply for lamp 2 (High voltage side) Sky Blue Power supply for lamp 3 (High voltage side) -Gray Power supply for lamp 1 (Low voltage side) -White Power supply for lamp 2 (Low voltage side) -Blue Power supply for lamp 3 (Low voltage side) -Black Power supply for lamp 4 (Low voltage side) -White Power supply for lamp 5 (Low voltage side) -Blue Power supply for lamp 6 (Low voltage side) -Black Power supply for lamp 4 (High voltage side) -White Power supply for lamp 5 (High voltage side) Sky Blue Power supply for lamp 6 (High voltage side) -Gray
Notes:
1. The high voltage power terminal is colored white,sky blue,gray. 2. The low voltage pin color is white,dark blue,black .
CN2
High High High Low Low Low Low Low Low High High High
CN3
CN5
Ver. 1.1
12 / 29
Product Specification
tHP
Note : Hsync Period and Hsync Width should be even number times of tCLK. If the value is odd number times of tCLK, display control signal can be asynchronous. In order to operate the LCD, Hsync, Vsync and DE(Data Enable) signals should be used. 1. The performance of the electro-optical characteristics may be influenced by variance of the vertical refresh rate. 2. Vsync and Hsync should be keep the above specification. 3. Hsync Period, Hsync Width and Horizontal Back Porch should be any times of character number(8).
Ver. 1.1
13 / 29
Product Specification
DCLK
tCLK
0.5 VDD
Invalid data
Pixel 0,0
Pixel 2,0
Invalid data
Invalid data
Pixel 1,0
Pixel 3,0
Invalid data
DE(Data Enable)
DE(Data Enable)
Ver. 1.1
14 / 29
Product Specification
R7 R6 R5 R4 R3 R2 R1 R0 G 7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
Black Red (255) Green (255) Basic Color Blue (255) Cyan Magenta Yellow White RED (000) RED (001) RED ... RED (254) RED (255) GREEN (000) GREEN (001) GREEN ... GREEN (254) GREEN (255) BLUE (000) BLUE (001) BLUE ... BLUE (254) BLUE (255)
0 1 0 0 0 1 1 1 0 0
0 1 0 0 0 1 1 1 0 0
0 1 0 0 0 1 1 1 0 0
0 1 0 0 0 1 1 1 0 0 ...
0 1 0 0 0 1 1 1 0 0
0 1 0 0 0 1 1 1 0 0
0 1 0 0 0 1 1 1 0 0
0 0 1 0 0 1 0 0 0 1 1 0 1 1 1 1 0 0 1 0
0 0 1 0 1 0 1 1 0 0
0 0 1 0 1 0 1 1 0 0
0 0 1 0 1 0 1 1 0 0 ...
0 0 1 0 1 0 1 1 0 0
0 0 1 0 1 0 1 1 0 0
0 0 1 0 1 0 1 1 0 0
0 0 0 0 1 0 0 1 1 1 0 1 1 0 1 1 0 0 0 0
0 0 0 1 1 1 0 1 0 0
0 0 0 1 1 1 0 1 0 0
0 0 0 1 1 1 0 1 0 0 ...
0 0 0 1 1 1 0 1 0 0
0 0 0 1 1 1 0 1 0 0
0 0 0 1 1 1 0 1 0 0
0 0 0 1 1 1 0 1 0 0
1 1 0 0
1 1 0 0
1 1 0 0
1 1 0 0 ...
1 1 0 0
1 1 0 0
1 1 0 0
0 0 1 0 0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0 ...
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0 0 0 1 0
0 0 0 0
0 0 0 0
0 0 0 0 ...
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0 ...
0 0 0 0
0 0 0 0
0 0 0 0
0 1 0 1 0 0 0 0
1 1 0 0
1 1 0 0
1 1 0 0 ...
1 1 0 0
1 1 0 0
1 1 0 0
0 0 1 0 0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0 ...
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 1
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0 0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 1 0 1
1 1
1 1
1 1
1 1
1 1
1 1
0 1
Note : Users should be input true 8 Bit data streams via LVDS transmitter.
Ver. 1.1
15 / 29
Product Specification
90%
90% 10%
10%
T1 T2
T5 T6
T7
10%
Valid Data
10%
0V
T3 T4
Notes : 1. Please avoid floating state of interface signal at invalid period. 2. When the interface signal is invalid, be sure to pull down the power supply for LCD VLCD to 0V. 3. Lamp power must be turn on after power supply for LCD an interface signal are valid.
Ver. 1.1
16 / 29
Product Specification
4. Optical Specification
Optical characteristics are determined after the unit has been ON and stable for approximately 30Min in a dark environment at 252C. The values are specified at an approximate distance 50cm from the LCD surface at a viewing angle of and equal to 0 . It is presented additional information concerning the measurement equipment and method in FIG. 1. LCD Module Optical Stage(x,y) Pritchard 880 or equivalent
50 cm FIG. 1 Optical Characteristic Measurement Equipment and Method Table 10. OPTICAL CHARACTERISTICS
Parameter Contrast Ratio Surface Luminance, white Luminance Variation Response Time Rise Time Decay Time RED Symbol CR LWH WHITE TrR TrD Rx Ry Gx Gy Bx By Wx Wy Viewing Angle (CR>10) x axis, right(=0) x axis, left (=180) y axis, up (=90) y axis, down (=270) Gray Scale r l u d 85 85 85 85 89 89 89 89 6 degree 5 Typ -0.03 5P 12 13 0.633 0.341 0.280 0.603 0.145 0.069 0.289 0.303 Typ +0.03
Ta= 252C, VLCD=12.0V, fV=60HzDclk=68.25MHz, IBL=7mA Values Min 420 360 Typ 600 450 Max 1.3 20 20 ms ms cd/m2 Units Notes 1 2 3 4 4
WHITE
Ver. 1.1
17 / 29
Product Specification
Note : 1. Contrast Ratio(CR) is defined mathematically as : Surface Luminance with all white pixels Surface Luminance with all black pixels It is measured at center 1-point. Contrast Ratio = 2. Surface Luminance(LWH) is the luminance value at center 1-point across the LCD surface 50cm from the surface with all pixels displaying white. For more information see the FIG. 2. 3. The variation of surface luminance , WHITE is defined as : WHITE(5P) = Maximum(Lon1,Lon2, Lon3, Lon4, Lon5) / Minimum(Lon1,Lon2, Lon3, Lon4, Lon5) Where Lon1 to Lon5 are the luminance with all pixels displaying white at 5 locations . For more information, see the FIG. 2. 4. Response time is the time required for the display to transition from G(N) to G(M) (Rise Time, TrR) and from G(M) to G(N) (Decay Time, TrD). For additional information see the FIG. 3. (N<M) 5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD module surface. For more information, see the FIG. 4. 6. Gray scale specification Gamma Value is approximately 2.2. For more information, see the Table 12. Table 12. GRAY SCALE SPECIFICATION Gray Level L0 L15 L31 L47 L63 L79 L95 L111 L127 L143 L159 L175 L191 L207 L223 L239 L255
Ver. 1.1 Jan. 04, 2005
Product Specification
Measuring point for surface luminance & measuring point for luminance variation
H A
The response time is defined as the following figure and shall be measured by switching the input signal for black and white.
TrD
black
black
Ver. 1.1
19 / 29
Product Specification
Normal E Y
= 90, Up
= 180, Left
= 0, Right
= 270, Down
Ver. 1.1
20 / 29
Product Specification
5. Mechanical Characteristics
The contents provide general mechanical characteristics. In addition the figures in the next page are detailed mechanical drawing of the LCD. Table 12. MECHANICAL CHARACTERISTICS
Horizontal Outline Dimension Vertical Depth Horizontal Bezel Area Vertical Horizontal Active Display Area Vertical Weight Surface Treatment 2500g (Typ.), 2650g(Max) Hard coating(3H) Anti-glare treatment of the front polarizer 223.488 mm 227.6 mm 372.48 mm 400.0 mm 258.0 mm 22.0 mm 376.6 mm
Notes : Please refer to a mechanic drawing in terms of tolerance at the next page.
Ver. 1.1
21 / 29
Product Specification
<FRONT VIEW>
Ver. 1.1
22 / 29
Product Specification
<REAR VIEW>
Ver. 1.1
23 / 29
Product Specification
6. Reliability
Table 13. ENVIRONMENT TEST CONDITION
No 1 2 3 4 Test Item Condition
High temperature storage test Low temperature storage test High temperature operation test Low temperature operation test
Ta= 60C 240h Ta= -20C 240h Ta= 50C 50%RH Ta= 0C 240h 240h
Wave form : random Vibration level : 1.0G RMS Bandwidth : 10-500Hz Duration : X,Y,Z, 20 min One time each direction Shock level : 100G Waveform : half sine wave, 2ms Direction : X, Y, Z One time each direction 0 - 10,000 feet(3048m) 0 - 40,000 feet(12,192m)
Ver. 1.1
24 / 29
Product Specification
7-2. EMC
a) ANSI C63.4 Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electrical Equipment in the Range of 9kHZ to 40GHz. American National Standards Institute(ANSI), 1992 b) C.I.S.P.R Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology Equipment. International Special Committee on Radio Interference. c) EN 55022 Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology Equipment. European Committee for Electrotechnical Standardization.(CENELEC), 1998 ( Including A1: 2000 )
Ver. 1.1
25 / 29
Product Specification
Note 1. Year
Year Mark 97 7 98 8 99 9 2000 0 2001 1 2002 2 2003 3 2004 4 2005 5 2006 6 2007 7
2. Month
Month Mark Jan 1 Feb 2 Mar 3 Apr 4 May 5 Jun 6 Jul 7 Aug 8 Sep 9 Oct A Nov B Dec C
3. Panel Code
Panel Code Mark P1 Factory 1 P2 Factory 2 P3 Factory 3 P4 Factory 4 P5 Factory 5 Hydis Panel H
4. Factory Code
Factory Code Mark LPL Gumi K LPL Nanjing C
5. Serial No
Serial No. Mark 1 ~ 99,999 00001 ~ 99999 100,000 ~ A0001 ~ A9999, - - - - , Z9999
b) Location of Lot Mark Serial NO. is printed on the label. The label is attached to the backside of the LCD module. This is subject to change without prior notice.
Product Specification
9. Precautions
Please pay attention to the followings when you use this TFT LCD module.
Product Specification
9-5. Storage
When storing modules as spares for a long time, the following precautions are necessary. (1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature between 5C and 35C at normal humidity. (2) The polarizer surface should not come in contact with any other object. It is recommended that they be stored in the container in which they were shipped.
Ver. 1.1
28 / 29
Product Specification
Ver. 1.1
29 / 29