Beruflich Dokumente
Kultur Dokumente
The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document. Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT. This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws. The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright Nokia Siemens Networks 2010/9/9. All rights reserved
The same text in German: Wichtiger Hinweis zur Produktsicherheit In elektrischen Anlagen stehen zwangslufig bestimmte Teile der Gerte unter Spannung. Einige Teile knnen auch eine hohe Betriebstemperatur aufweisen. Eine Nichtbeachtung dieser Situation und der Warnungshinweise kann zu Krperverletzungen und Sachschden fhren. Deshalb wird vorausgesetzt, dass nur geschultes und qualifiziertes Personal die Anlagen installiert und wartet. Das System entspricht den Anforderungen der EN 60950 / IEC 60950. Angeschlossene Gerte mssen die zutreffenden Sicherheitsbestimmungen erfllen.
Id:0900d80580635bef
Table of Contents
This document has 164 pages. Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1 2 2.1 2.2 2.3 2.4 2.5 3 4 5 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 5.12 5.13 5.14 5.15 5.16 5.17 5.18 5.19 5.20 5.21 5.22 5.23 5.24 5.25 5.26 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Use of clear codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Traffic observation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Traffic measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maintenance supervision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Detailed charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Field reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 13 13 13 13 13
Presentation of clear codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Effective and ineffective cause codes . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Clear codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 000H - NORMAL END OF CALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 001H - SUSPENDED CALL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 003H - CALL DURATION BELOW SUPERVISION TIME . . . . . . . . . . . 23 004H - B BUSY OR CONGESTION RECEIVED FROM OUTGOING CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 005H - CALLED SUBSCRIBER BUSY . . . . . . . . . . . . . . . . . . . . . . . . . 24 006H - TIME-OUT FOR B-SUBSCRIBER ANSWER . . . . . . . . . . . . . . 24 007H - CALL WAITING TIME-OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 008H - CALLED SUBSCRIBER NOT CONNECTED . . . . . . . . . . . . . . 26 009H - CALL ALREADY WAITING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 00AH - INTERVENTION ALREADY ON . . . . . . . . . . . . . . . . . . . . . . . . 27 00BH - REROUTING DUE TO B-SUBSCRIBER FACILITY . . . . . . . . . 27 00CH - OUTGOING DIRECTION RESTRICTED DUE TO CRISIS MODE 28 00EH - MALICIOUS CALL TRACING . . . . . . . . . . . . . . . . . . . . . . . . . . 28 00FH - INTERMEDIATE CHARGING . . . . . . . . . . . . . . . . . . . . . . . . . . 29 010H - ABSENT SUBSCRIBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 011H - OPERATOR PRIORITY ACCESS . . . . . . . . . . . . . . . . . . . . . . . 30 012H - NO PAGING RESPONSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 013H - CALL TRANSFER RECALL DUE TO C-SUBSCRIBER ANSWER TIME-OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 015H - NORMAL UNSPECIFIED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 016H - SUBSCRIBER'S CHARGING CAPACITY EXCEEDED IN THE EXCHANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 018H - INTERMEDIATE CHARGING IN THE END OF THE PHASE CHARGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 020H - ANNOUNCEMENT SUCCESS IN INTERCEPTION . . . . . . . . . 33 025H - CALL DROP BACK RELEASE . . . . . . . . . . . . . . . . . . . . . . . . . 34 031H - NOT ENOUGH CREDIT TO CALL . . . . . . . . . . . . . . . . . . . . . . 35 100H - CIRCUIT RE-SEIZED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 101H - CIRCUIT RELEASED BEFORE 'END OF THE CALL' NOTICE 36
Id:0900d80580635bef
5.27 5.28 5.29 5.30 5.31 5.32 5.33 5.34 5.35 5.36 5.37 5.38 5.39 5.40 5.41 5.42 5.43 5.44 5.45 5.46 5.47 5.48 5.49 5.50 5.51 5.52 5.53 5.54 5.55 5.56 5.57 5.58 5.59 5.60 5.61 5.62 5.63 5.64 5.65 5.66 5.67
102H - CALL RECORD RELEASED DURING CALIBRATION . . . . . . . 36 103H - CHARGING IN WRONG PHASE OF CALL . . . . . . . . . . . . . . . . 37 201H - CALL RELEASED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 202H - CLEAR REQUEST RECEIVED FROM OUTGOING CIRCUIT. . 38 203H - B-CHANNEL UNACCEPTABLE . . . . . . . . . . . . . . . . . . . . . . . . . 39 204H - ESTABLISHED B-CHANNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 206H - CALL REJECTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 207H - SUBSCRIBER CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . . 40 20BH - CLEAR IN DETAILED CHARGING . . . . . . . . . . . . . . . . . . . . . . 41 20EH - CALLING SUBSCRIBER LINE VACANT OR OUT OF SERVICE . 41 20FH - CHANGE OF OUTGOING CIRCUIT . . . . . . . . . . . . . . . . . . . . . 42 210H - NULL NUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 211H - NETWORK, REJECTED DIVERTED CALLS . . . . . . . . . . . . . . . 43 213H - NETWORK, USER NOT IN CUG . . . . . . . . . . . . . . . . . . . . . . . . 44 215H - CALL DROP BACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 216H - MISDIALLED TRUNK PREFIX . . . . . . . . . . . . . . . . . . . . . . . . . . 45 217H - TEMPORARY OUT OF ORDER . . . . . . . . . . . . . . . . . . . . . . . . . 45 218H - OUT OF CATCHMENT AREA . . . . . . . . . . . . . . . . . . . . . . . . . . 46 219H - TRANSLATION OUT-OF-SERVICE . . . . . . . . . . . . . . . . . . . . . . 47 220H - ANONYMOUS CALLS REJECTION . . . . . . . . . . . . . . . . . . . . . . 47 252H - UNTERMINATED CALL TO A PORTED NUMBER . . . . . . . . . . 48 300H - CALLING SUBSCRIBER BARRED DUE TO RESTRICTION IN THE OUTGOING DIRECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 301H - CALLING SUBSCRIBER'S OUTGOING CALL RESTRICTED BY OPERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 304H - CALLED SUBSCRIBER LINE OUT OF SERVICE . . . . . . . . . . . 50 305H - CALLED SUBSCRIBER LINE FAULTY . . . . . . . . . . . . . . . . . . . 50 306H - ACCESS TO B-SUBSCRIBER LINE RESTRICTED . . . . . . . . . 51 307H - B-NUMBER UNUSED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 308H - B-NUMBER CHANGED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 309H - TIME-OUT WHEN WAITING FOR OPERATOR'S INTERVENTION 53 30AH - CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK DURING SET-UP PHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 30BH - CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK WHEN WAITING FOR ANSWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 30CH - REANSWER TIME OUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 30DH - B- OR C-NUMBER IS NOT REGISTERED . . . . . . . . . . . . . . . . 55 30EH - CALLED SUBSCRIBER LINE BLOCKED . . . . . . . . . . . . . . . . . 56 30FH - CHANGE IN NUMBERING PLAN. . . . . . . . . . . . . . . . . . . . . . . . 56 310H - CLOSED USER GROUP RESCTRICTION . . . . . . . . . . . . . . . . 57 311H - BEARER SERVICE NOT PROVIDED . . . . . . . . . . . . . . . . . . . . 57 312H - TELESERVICE NOT PROVIDED . . . . . . . . . . . . . . . . . . . . . . . . 58 315H - CALLED SUBSCRIBER HAS CALL DIVERSION BARRING . . . 58 317H - TIME-OUT IN INTELLIGENT NETWORK BASED SUBSCRIBER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 31AH - INCOMING CALLS BARRED WITHIN THE CUG . . . . . . . . . . . 60
Id:0900d80580635bef
5.68 5.69 5.70 5.71 5.72 5.73 5.74 5.75 5.76 5.77 5.78 5.79 5.80 5.81 5.82 5.83 5.84 5.85 5.86 5.87 5.88 5.89 5.90 5.91 5.92 5.93 5.94 5.95 5.96 5.97 5.98 5.99 5.100 5.101 5.102 5.103 5.104 5.105 5.106 5.107 5.108 5.109 5.110 5.111 5.112
31CH - SUBSCRIBER NOT A MEMBER OF THE CUG . . . . . . . . . . . . 60 31DH - OUTGOING CALLS BARRED WITHIN THE CUG . . . . . . . . . . 61 321H - NO CUG SELECTED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 322H - UNKNOWN CUG INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 400H - ATTENUATOR CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . 63 401H - INTERWORKING UNIT CONGESTION . . . . . . . . . . . . . . . . . . 63 402H - REGISTER TOTAL TIME EXCEEDED . . . . . . . . . . . . . . . . . . . 64 403H - MFCU DEVICE CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . 65 404H - PBRU DEVICE CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . 65 405H - ERRONEOUS SERVICE REQUEST FROM CO-PROCESS . . 66 406H - CONNECTION FAILED IN GSW/SWI . . . . . . . . . . . . . . . . . . . . 66 407H - ERRONEOUS ANSWER FROM PARTNER PROGRAM BLOCK. 67 408H - LENGTH OF CALLED SUBSCRIBER NUMBER EXCEEDED . 68 409H - CONNECTION FAILED IN SSW/SWI . . . . . . . . . . . . . . . . . . . . 69 40AH - CIRCUIT CONGESTION DUE TO TRAFFIC TYPE . . . . . . . . . 69 40BH - HOP COUNTER EXHAUST . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 506H - LINES OF LINE HUNTING GROUPS BARRED . . . . . . . . . . . . 71 508H - CHARGING ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 509H - FILE ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 50BH - MODULE ROUTE OR SSW CONGESTION . . . . . . . . . . . . . . . 72 50CH - MFC-ASS-CHANNEL CLOSING MISSED . . . . . . . . . . . . . . . . 73 50DH - FACILITY CONTROL FAILED. . . . . . . . . . . . . . . . . . . . . . . . . . 73 50FH - UNSUITABLE MODULE CIRCUIT . . . . . . . . . . . . . . . . . . . . . . 74 600H - FILE RECORD CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . 75 601H - MODULE OR V5 CONGESTION. . . . . . . . . . . . . . . . . . . . . . . . 75 602H - REGISTER CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 603H - NO RESPONSE FROM PARTNER PROGRAM BLOCK . . . . . 76 604H - INTERNAL CALL LINK CONGESTION . . . . . . . . . . . . . . . . . . . 77 606H - CONFERENCE DEVICE CONGESTION . . . . . . . . . . . . . . . . . 78 607H - POLARITY REVERSAL FAILURE . . . . . . . . . . . . . . . . . . . . . . . 78 608H - CHARGING NOT STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 609H - CALL CLEARED BY MML . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 60BH - OVERLOAD CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 60DH - STAGE CIRCUIT CONGESTION . . . . . . . . . . . . . . . . . . . . . . . 81 60EH - UNIT RESTARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 60FH - SUBSCRIBER MODULE OR V5 INTERFACE FAILURE, CALL CLEARED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 700H - LONG AON REQUEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 701H - REGISTER ANALYSIS FAILED. . . . . . . . . . . . . . . . . . . . . . . . . 83 702H - QUEUEING TIME EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . 84 704H - PARITY ERROR FROM PBRU/MFCU DEVICE . . . . . . . . . . . . 84 705H - MODULE OR V5 INTERFACE NOT AVAILABLE . . . . . . . . . . . 85 706H - CALL INTERRUPTED DURING REGISTER ANALYSIS . . . . . 86 707H - SUBSCRIBER MODULE RESTARTED. . . . . . . . . . . . . . . . . . . 86 70AH - FORCED CLEAR OF A CALL . . . . . . . . . . . . . . . . . . . . . . . . . . 87 70BH - MODEM ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Id:0900d80580635bef
5.113 5.114 5.115 5.116 5.117 5.118 5.119 5.120 5.121 5.122 5.123 5.124 5.125 5.126 5.127 5.128 5.129 5.130 5.131 5.132 5.133 5.134 5.135 5.136 5.137 5.138 5.139 5.140 5.141 5.142 5.143 5.144 5.145 5.146 5.147 5.148 5.149 5.150 5.151 5.152 5.153 5.154 5.155
70CH - OVERLOAD CONTROL SYSTEM ERROR . . . . . . . . . . . . . . . . 88 70DH - ANNOUNCEMENT SERVICE FAILURE . . . . . . . . . . . . . . . . . . 88 70EH - CONFIGURATION ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 710H - NO ANALYSIS FOR CARRIER ACCESS CODE . . . . . . . . . . . . 89 711H - TARIFF NOT ACCEPTED BY TRANSIT EXCHANGE . . . . . . . . 90 712H - TARIFF NOT ACCEPTED BY ORIGINATING OR INTERWORKING EXCHANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 713H - NO ISUP ROUTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 714H - ATTRIBUTE DIRECTED ROUTING MISMATCH . . . . . . . . . . . . 91 715H - REQUESTED FACILITY WAS NOT AVAILABLE ON THE OUTGOING ROUTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 716H - REQUESTED BEARER CAPABILITY COULD NOT BE FULFILLED ON THE ROUTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 718H - DIGIT ANALYSIS IN CENTRAL MEMORY RESULTED IN CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 719H - NO RESOURCE AVAILABLE FOR CALL . . . . . . . . . . . . . . . . . 94 71AH - IDENTIFIED CHANNEL NOT EXIST . . . . . . . . . . . . . . . . . . . . . 95 71BH - REQUESTED CHANNEL NOT AVAILABLE . . . . . . . . . . . . . . . 95 71CH - PACKET CONTROL UNIT CONGESTION . . . . . . . . . . . . . . . . 96 71DH - POINT-TO-POINT PROTOCOL ERROR . . . . . . . . . . . . . . . . . . 96 801H - LENGTH OF ORIGINAL CALLED SUBSCRIBER NUMBER EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 802H - LENGTH OF CALLING SUBSCRIBER NUMBER EXCEEDED . 97 803H - INVALID CALLING SUBSCRIBER CATEGORY . . . . . . . . . . . . 98 804H - OUTGOING CIRCUIT CONGESTION . . . . . . . . . . . . . . . . . . . . 99 806H - IDENTITY OF CALLING SUBSCRIBER IS NOT AVAILABLE . . 99 809H - ERRONEOUS MFC SIGNAL FROM OUTGOING CIRCUIT . . 100 80AH - ERRONEOUS MFC SIGNAL FROM INCOMING CIRCUIT . . . 101 80BH - NO B-NUMBERS TO SEND TO OUTGOING CIRCUIT. . . . . . 101 80CH - UNKNOWN DECADIC SIGNAL FROM INCOMING CIRCUIT. 102 80DH - OUTGOING CIRCUIT OUT OF ORDER . . . . . . . . . . . . . . . . . 102 80EH - INCOMING CIRCUIT OUT OF ORDER . . . . . . . . . . . . . . . . . . 103 80FH - CIRCUIT CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 810H - FACILITY NOT SUPPORTED . . . . . . . . . . . . . . . . . . . . . . . . . 104 811H - NETWORK FAILURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 813H - SWITCHING EQUIPMENT CONGESTION . . . . . . . . . . . . . . . 105 814H - CIRCUIT GROUP CONGESTION . . . . . . . . . . . . . . . . . . . . . . 105 815H - ACCESS BARRED TO THE CALLED SUBSCRIBER . . . . . . . 106 816H - CALL FAILED, SEND SPECIAL INFORMATION TONE . . . . . 106 817H - NETWORK, UNALLOCATED NUMBER. . . . . . . . . . . . . . . . . . 107 818H - NETWORK, LINE OUT OF SERVICE . . . . . . . . . . . . . . . . . . . 107 819H - NETWORK, SUBSCRIBER NUMBER CHANGED . . . . . . . . . . 108 81AH - CONGESTION IN TERMINAL EXCHANGE. . . . . . . . . . . . . . . 109 81DH - CONGESTION IN INTERNATIONAL CALL . . . . . . . . . . . . . . . 109 81EH - CONTROLLED NOT READY . . . . . . . . . . . . . . . . . . . . . . . . . . 110 81FH - NETWORK, OVERLOAD CONGESTION . . . . . . . . . . . . . . . . 110 820H - NETWORK MESSAGE CONTENT ERROR. . . . . . . . . . . . . . . 111 821H - INVALID TRANSIT NETWORK SELECTION . . . . . . . . . . . . . . 111
Id:0900d80580635bef
5.156 5.157 5.158 5.159 5.160 5.161 5.162 5.163 5.164 5.165 5.166 5.167 5.168 5.169 5.170 5.171 5.172 5.173 5.174 5.175 5.176 5.177 5.178 5.179 5.180 5.181 5.182 5.183 5.184 5.185 5.186 5.187 5.188 5.189 5.190 5.191 5.192 5.193
822H - RECOVERY ON TIMER EXPIRY . . . . . . . . . . . . . . . . . . . . . . 112 824H - PCM FAULTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 828H - CONGESTION FROM NATIONAL NETWORK . . . . . . . . . . . . 113 829H - DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 830H - NUMBER PORTABILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 832H - ROUTING ERROR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 833H - DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT FAILURE 116 851H - TRAFFIC TO CONGESTED DESTINATION POINT CODE RESTRICTED BY SIGNALLING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 900H - NO MF FORWARD SIGNAL . . . . . . . . . . . . . . . . . . . . . . . . . . 117 901H - TOO LONG MF FORWARD SIGNAL . . . . . . . . . . . . . . . . . . . 117 905H - TOO LONG MF BACKWARD SIGNAL . . . . . . . . . . . . . . . . . . 118 90CH - PREMATURE ACKNOWLEDGEMENT TO SEIZURE IN OUTGOING CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 90EH - PREMATURE ANSWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 90FH - ANSWER AFTER B BUSY . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 A01H - CLEARED FORWARD (SEIZING ACKNOWLEDGED SIGNAL MISSING) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 A02H - INVALID MESSAGE FROM TRUNK CIRCUIT . . . . . . . . . . . . 121 A03H - INTERWORKING FAILED. . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 A04H - TRUNK CIRCUIT PROTOCOL ERROR . . . . . . . . . . . . . . . . . 122 A05H - CIRCUIT RELEASED BY CO-EXCHANGE . . . . . . . . . . . . . . 122 A07H - CALL FAILURE FROM OUTGOING CIRCUIT . . . . . . . . . . . . 123 A08H - INTER-EXCHANGE SIGNALLING OUT OF ORDER . . . . . . . 123 A09H - ADDRESS COMPLETE MESSAGE TIME-OUT . . . . . . . . . . . 124 A0AH - ADDRESS COMPLETE MESSAGE SENDING TIME EXCEEDED 125 A0CH - NO DIGITAL TRUNK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 A0DH - NO ROUTE TO SPECIFIED TRANSIT OR TO DESTINATION . . 126 A0EH - NO CIRCUIT AVAILABLE IN TRANSIT NETWORK. . . . . . . . 126 A0FH - RESELECTION IN TRANSIT NETWORK APPLYING LOAD SHARING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 B02H - TRANSIT/TERMINAL SIGNAL WAIT TIME SUPERVISION EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 B0FH - LENGTH OF CHANGED CALLED SUBSCRIBER NUMBER EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 B11H - MODEM COMMUNICATION ERROR. . . . . . . . . . . . . . . . . . . 129 B17H - ADDRESS INCOMPLETE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 B18H - SERVICE UNAVAILABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 B19H - SERVICE INCOMPATIBLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 B20H - NETWORK ADDRESS EXTENSION (NAE) ERROR . . . . . . . 131 B21H - DTE IS UNCONTROLLED . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 B23H - DUAL SEIZURE FROM BIDIRECTIONAL CIRCUIT. . . . . . . . 132 B2AH - BLOCKING RECEIVED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 B2BH - PARAMETER DOES NOT EXIST OR IS NOT IMPLEMENTED . 133
Id:0900d80580635bef
5.194 5.195 5.196 5.197 5.198 5.199 5.200 5.201 5.202 5.203 5.204 5.205 5.206 5.207 5.208 5.209 5.210 5.211 5.212 5.213 5.214 5.215 5.216 5.217 5.218 5.219 5.220 5.221 5.222 5.223 5.224 5.225 5.226 5.227 5.228 5.229 5.230
B2CH - INTELLIGENT NETWORK APPLICATION PROTOCOL ERROR. 133 B2DH - INTELLIGENT NETWORK APPLICATION RESPONSE TIMEOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 B2EH - MAXIMUM NUMBER OF TRIGGERING EVENTS IN A CALL HAS BEEN REACHED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 B2FH - TCAP ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 B30H - ASN1 CODING OR DECODING ERROR . . . . . . . . . . . . . . . . 136 B31H - SELECTIVE CALL CONGESTION HAS PREVENTED CALL ATTEMPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 B32H - CALL RELEASE ORDERED BY INTELLIGENT NETWORK APPLICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 B33H - CONTINUITY CHECK FAILURE . . . . . . . . . . . . . . . . . . . . . . . 137 B34H - A-NUMBER IS NOT THE REGISTERED NUMBER OF AN INDIRECT SUBSCRIBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 B35H - TOO MANY FRAUDULENT ATTEMPTS TO USE CALLING CARD 138 B36H - CALLING CARD NUMBER SELECTED BY USER NOT FOUND . 139 B37H - IN-SERVICE INTERRUPTED FOR SUSPECTED FRAUD . . . 140 B38H - IN FALLBACK CODE ONE. . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 B39H - IN FALLBACK CODE TWO . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 B3AH - IN FALLBACK CODE THREE . . . . . . . . . . . . . . . . . . . . . . . . . 141 B3BH - IN FALLBACK CODE FIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 B3CH - IN FALLBACK CODE FOUR . . . . . . . . . . . . . . . . . . . . . . . . . . 143 B3DH - IN DIALOG - ROUTING FAILURE IN SS7 NETWORK . . . . . . 143 C00H - DIAL WAIT TIME EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . 144 C01H - PROHIBITED DIALLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 C02H - INSUFFICIENT DIALLING FROM SUBSCRIBER SIGNALLING . . 145 C04H - CALLING SUBSCRIBER HAS DIALLED WRONG KEYWORD. . . 146 C05H - CALLING SUBSCRIBER HAS NO RIGHT TO FACILITY . . . . 146 C06H - CALLING SUBSCRIBER HAS NO RIGHT TO STORE NUMBER . 147 C08H - PREMATURE DIALLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 C09H - SERVICE OR FACILITY ACTIVATION RESTRICTED . . . . . . 148 C0AH - SERVICE OR FACILITY USAGE RESTRICTED. . . . . . . . . . . 149 C0BH - INCONSISTENCY BETWEEN A- AND B-SUBSCRIBERS . . . 149 C0DH - BEARER CAPABILITY NOT PRESENTLY AVAILABLE . . . . . 150 D00H - SUBSCRIBER SIGNALLING MESSAGE CONTENT ERROR 150 D01H - SUBSCRIBER SIGNALLING MESSAGE FORMAT ERROR. . 151 D03H - SERVICE OR FUNCTION NOT IMPLEMENTED . . . . . . . . . . 151 D04H - SUBSCRIBER SIGNALLING PROTOCOL ERROR . . . . . . . . 152 D06H - AOCC CHARGING ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 D07H - NO RESPONSE TO CALL ESTABLISHMENT: ALERTING OR CONNECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 D08H - GSM ERH 4.08 PROTOCOL TIMER EXPIRES. . . . . . . . . . . . 154 D0BH - DUAL LOG-IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Id:0900d80580635bef
D0FH - ISDN-SUBSCRIBER FACILITY DIALLING REJECTED . . . . . 155 D10H - MANDATORY INFORMATION ELEMENT MISSING . . . . . . . 155 D11H - INVALID INFORMATION ELEMENT CONTENT . . . . . . . . . . 156 Clear code index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Id:0900d80580635bef
Summary of changes
Summary of changes
Changes between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues. Changes made between issues 11 and 10 Chapters Effective and ineffective clear codes, Clear codes and Clear code index Added codes 0821H and 0C0DH. Changes made between issues 10 and 9 Chapters Effective and ineffective clear codes, Clear codes and Clear code index Added clear codes: 0012H, 0030H, 0031H, 0252H, 040BH, 070BH, 071CH, 071DH, 0832H, 0833H, 0A0EH, 0A0FH and 0B11H Chapter Clear codes Modified clear codes: 0719H, the default effect of the clear code has been changed. Changes made between issues 9 and 8 Chapters Effective and ineffective clear codes, Clear codes and Clear code index Added clear codes: 0025H, 0216H, 0217H, 0218H, 0219H, 0220H, 050EH, 0710H, 081EH and 0830H
10
Id:0900d80580635beb
Introduction
1 Introduction
The DX 200 Clear Code List contains descriptions of all clear codes sent from the call control program blocks to the statistical process. This manual also describes the use of the clear codes in the DX 200 system. Clear codes have been given hexadecimal numbers from 0000H to 0FFFH. Clear codes have been divided into four main classes: 0000H - 03FFH: normal clearing 0400H - 07FFH: internal congestion 0800H - 0BFFH: external congestion 0C00H - 0FFFH: subscriber errors
The main class 'normal clearing' consists of clear codes which have not been caused by error in the network element or by subscriber error, but which nevertheless lead to clearing of a call or to an interruption in call set-up. The class has been further divided into four subclasses 0000H - 00FFH: normal clearing / normal clearing: normal clearing situations, for example, subscriber busy 0100H - 01FFH: normal clearing / internal congestion: clear codes set by charging and statistics and not leading to a release 0200H - 02FFH: normal clearing / external congestion: normal clearing situations, caused by a congestion outside the network element, for example, by a congestion on the radio path 0300H - 03FFH: normal clearing / subscriber error: normal congestion caused by the subscriber's facility or equipment.
. The second main class, 'internal congestion' (0400H - 07FFH) consists of cases in which a call or call set-up is interrupted because of an error in the originating exchange. Primarily, the class contains clear codes associated with communication between the various units and program blocks of the exchange and those associated with handling of files. The third main class, 'external congestion' (0800H -0BFFH) includes all the cases in which a call or call set-up is interrupted because of an error outside the originating exchange. This group consists mainly of clear codes related to inter-exchange signalling. The fourth main class, 'subscriber errors' (0C00H - 0FFFH) includes the cases in which a call or call set-up is interrupted by a calling subscriber's error or by a failure in the subscriber's equipment or by faulty subscriber signalling. The clear codes are transferred from the call control to the statistical system in the following messages: charging facility charging (facility control) call set-up interrupted call interrupted
The clear codes affect both the tasks and outputs of the following system blocks and program blocks: Call Control (CLCSYB)
Id:0900d80580635beb
11
Introduction
Signalling Services (SGLSYB Statistical Program Block (STPROC) Charging Program Block (CGPROC) Charging Control Program Block (CGLSTA) Text Forming Program Block (TEXTPR) Traffic Measurement Program Block (TRAMNT) Traffic Measurement MML (TRMSNT) Traffic Observation MML (TROBSN)
12
Id:0900d80580635beb
2.1
Traffic observation
Traffic observation uses individual clear codes. In two observation categories, that is, in destination observation and in the observation of failed calls, the observation can be limited to a certain clear code, for example, 0804H, or to a certain clear code range, for example, 0400H - 07FFH. This means that traffic observation reports are given only on calls that fall into the defined category. In other observation categories, clear codes have no function.
2.2
Traffic measurement
Traffic measurement uses the main classes of clear codes.
2.3
Maintenance supervision
Supervision of the error ratio of circuit groups and control units is part of the maintenance supervision. Here, it is important to distinguish between 'normal clearing' and 'clearing due to error', irrespective of the cause of error.
2.4
Detailed charging
Individual clear codes received in the charging messages and facility charging messages are significant for detailed charging.
2.5
Field reporting
Individual clear codes and the classification of clear codes in the Service Level File of the statistics system are used in field reporting. The Service Level File can be defined to include eight code groups, which may comprise any clear codes (0000H - 0FFFH). The number of occurrences of the clear codes belonging to these groups are updated, group by group, to the Service Level File. The occurrences of each clear code are also registered in the Service Level File.
Id:0900d80580635beb
13
Possibility to change the default effect This field states whether it is possible to change the default effect. Alarms A list of possible alarms which are set when the clear code occurs in the exchange.
14
Id:0900d80580635beb
Id:0900d80580635beb
15
0204H 0206H 0207H 020BH 020EH 020FH 0210H 0211H 0213H 0215H 0216H 0217H 0218H 0219H 0220H 0252H 0300H 0301H 0304H 0305H 0306H 0307H 0308H 0309H 030AH 030BH 030CH 030DH 030EH 030FH 0310H 0311H 0312H 0315H 0317H 031AH
ESTABLISHED B-CHANNEL CALL REJECTED SUBSCRIBER CONGESTION CLEAR IN DETAILED CHARGING CALLING SUBSCRIBER LINE VACANT OR OUT OF SERVICE CHANGE OF OUTGOING CIRCUIT NULL NUP NETWORK, REJECTED DIVERTED CALLS NETWORK, USER NOT IN CUG CALL DROP BACK MISDIALLED TRUNK PREFIX TEMPORARY OUT OF ORDER OUT OF CATCHMENT AREA TRANSLATION OUT-OF-SERVICE ANONYMOUS CALLS REJECTION UNTERMINATED CALL TO A PORTED NUMBER CALLING SUBSCRIBER BARRED DUE TO RESTRICTION IN THE OUTGOING DIRECTION CALLING SUBSCRIBER'S OUTGOING CALL RESTRICTED BY OPERATOR CALLED SUBSCRIBER LINE OUT OF SERVICE CALLED SUBSCRIBER LINE FAULTY ACCESS TO B-SUBSCRIBER LINE RESTRICTED B-NUMBER UNUSED B-NUMBER CHANGED TIME-OUT WHEN WAITING FOR OPERATOR'S INTERVENTION CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK DURING SET-UP PHASE CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK WHEN WAITING FOR ANSWER REANSWER TIME OUT B- OR C-NUMBER IS NOT REGISTERED CALLED SUBSCRIBER LINE BLOCKED CHANGE IN NUMBERING PLAN CLOSED USER GROUP RESCTRICTION BEARER SERVICE NOT PROVIDED TELESERVICE NOT PROVIDED CALLED SUBSCRIBER HAS CALL DIVERSION BARRING TIME-OUT IN INTELLIGENT NETWORK BASED INCOMING CALLS BARRED WITHIN THE CUG
16
Id:0900d80580635beb
031CH 031DH 0321H 0322H 0400H 0401H 0402H 0403H 0404H 0405H 0406H 0407H 0408H 0409H 040AH 040BH 0506H 0508H 0509H 050BH 050CH 050DH 050EH 050FH 0600H 0601H 0602H 0603H 0604H 0606H 0607H 0608H 0609H 060BH 060DH 060EH 060FH 0700H
SUBSCRIBER NOT A MEMBER OF THE CUG OUTGOING CALLS BARRED WITHIN THE CUG NO CUG SELECTED UNKNOWN CUG INDEX ATTENUATOR CONGESTION INTERWORKING UNIT CONGESTION REGISTER TOTAL TIME EXCEEDED MFCU DEVICE CONGESTION PBRU DEVICE CONGESTION ERRONEOUS SERVICE REQUEST FROM C0-PROCESS CONNECTION FAILED IN GSW/SWI ERRONEOUS ANSWER FROM PARTNER PROGRAM BLOCK LENGTH OF CALLED SUBSCRIBER NUMBER EXCEEDED CONNECTION FAILED IN SSW/SWI CIRCUIT CONGESTION DUE TO TRAFFIC TYPE HOP COUNTER EXHAUST LINES OF LINE HUNTING GROUPS BARRED CHARGING ERROR FILE ERROR MODULE ROUTE OR SSW CONGESTION MFC-ASS-CHANNEL CLOSING MISSED FACILITY CONTROL FAILED UPDATE LOG BLOCKING UNSUITABLE MODULE CIRCUIT FILE RECORD CONGESTION MODULE OR V5 CONGESTION REGISTER CONGESTION NO RESPONSE FROM PARTNER PROGRAM BLOCK INTERNAL CALL LINK CONGESTION CONFERENCE DEVICE CONGESTION POLARITY REVERSAL FAILURE CHARGING NOT STARTED CALL CLEARED BY MML OVERLOAD CONGESTION STAGE CIRCUIT CONGESTION UNIT RESTARTED SUBSCRIBER MODULE OR V5 INTERFACE FAILURE, CALL CLEARED LONG AON REQUEST
Id:0900d80580635beb
17
0701H 0702H 0704H 0705H 0706H 0707H 070AH 070BH 070CH 070DH 070EH 0710H 0711H 0712H 0713H 0714H 0715H 0716H 0718H 0719H 071AH 071BH 071CH 071DH 0801H 0802H 0803H 0804H 0806H 0807H 0808H 0809H 080AH 080BH 080CH 080DH
REGISTER ANALYSIS FAILED QUEUEING TIME EXCEEDED PARITY ERROR FROM PBRU/MFCU DEVICE MODULE OR V5 INTERFACE NOT AVAILABLE CALL INTERRUPTED DURING REGISTER ANALYSIS SUBSCRIBER MODULE RESTARTED FORCED CLEAR OF A CALL MODEM ERROR OVERLOAD CONTROL SYSTEM ERROR ANNOUNCEMENT SERVICE FAILURE CONFIGURATION ERROR NO ANALYSIS FOR CARRIER ACCESS CODE TARIFF NOT ACCEPTED BY TRANSIT EXCHANGE TARIFF NOT ACCEPTED BY ORIGINATING OR INTERWORKING EXCHANGE NO ISUP ROUTE ATTRIBUTE DIRECTED ROUTING MISMATCH REQUESTED FACILITY WAS NOT AVAILABLE ON THE OUTGOING ROUTE REQUESTED BEARER CAPABILITY COULD NOT BE FULFILLED ON THE ROUTE DIGIT ANALYSIS IN CENTRAL MEMORY RESULTED IN CONGESTION NO RESOURCE AVAILABLE FOR CALL IDENTIFIED CHANNEL NOT EXIST REQUESTED CHANNEL NOT AVAILABLE PACKET CONTROL UNIT CONGESTION POINT-TO-POINT PROTOCOL ERROR LENGTH OF ORIGINAL CALLED SUBSCRIBER EXCEEDED LENGTH OF CALLING SUBSCRIBER NUMBER EXCEEDED INVALID CALLING SUBSCRIBER CATEGORY OUTGOING CIRCUIT CONGESTION IDENTITY OF CALLING SUBSCRIBER IS NOT AVAILABLE WAITING TIME FOR MFC PAUSE SIGNAL EXCEEDED WAITING TIME FOR MFC BACKWARD SIGNAL EXCEEDED ERRONEOUS MFC SIGNAL FROM OUTGOING CIRCUIT ERRONEOUS MFC SIGNAL FROM INCOMING CIRCUIT NO B-NUMBERS TO SEND TO OUTGOING CIRCUIT UNKNOWN DECADIC SIGNAL FROM INCOMING OUTGOING CIRCUIT OUT OF ORDER
18
Id:0900d80580635beb
080EH 080FH 0810H 0811H 0813H 0814H 0815H 0816H 0817H 0818H 0819H 081AH 081DH 081EH 081FH 0820H 0821H 0822H 0824H 0828H 0829H 0830H 0832H 0833H 0851H 0900H 0901H 0905H 090CH 090DH 090EH 090FH 0A01H 0A02H 0A03H 0A04H 0A05H
INCOMING CIRCUIT OUT OF ORDER CIRCUIT CONGESTION FACILITY NOT SUPPORTED NETWORK FAILURE SWITCHING EQUIPMENT CONGESTION CIRCUIT GROUP CONGESTION ACCESS BARRED TO THE CALLED SUBSCRIBER CALL FAILED, SEND SPECIAL INFORMATION TONE NETWORK, UNALLOCATED NUMBER NETWORK, LINE OUT OF SERVICE NETWORK, SUBSCRIBER NUMBER CHANGED CONGESTION IN TERMINAL EXCHANGE CONGESTION IN INTERNATIONAL CALL CONTROLLED NOT READY NETWORK, OVERLOAD CONGESTION NETWORK MESSAGE CONTENT ERROR INVALID TRANSIT NETWORK SELECTION RECOVERY ON TIMER EXPIRY PCM FAULTY CONGESTION FROM NATIONAL NETWORK DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT CONGESTION NUMBER PORTABILITY ROUTING ERROR DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT FAILURE TRAFFIC TO CONGESTED DESTINATION POINT NO MF FORWARD SIGNAL TOO LONG MF FORWARD SIGNAL TOO LONG MF BACKWARD SIGNAL PREMATURE ACKNOWLEDGEMENT TO SEIZURE IN OUTGOING CIRCUIT WAITING TIME FOR ACKNOWLEDGEMENT TO SEIZURE IN OUTGOING CIRCUIT EXCEEDED PREMATURE ANSWER ANSWER AFTER B BUSY CLEARED FORWARD (SEIZING ACKNOWLEDGED SIGNAL MISSING) INVALID MESSAGE FROM TRUNK CIRCUIT INTERWORKING FAILED TRUNK CIRCUIT PROTOCOL ERROR CIRCUIT RELEASED BY CO-EXCHANGE
Id:0900d80580635beb
19
0A07H 0A08H 0A09H 0A0AH 0A0CH 0A0DH 0A0EH 0A0FH 0B02H 0B0FH 0B11H 0B17H 0B18H 0B19H 0B20H 0B21H 0B23H 0B2AH 0B2BH 0B2DH 0B2CH 0B2EH 0B2FH 0B30H 0B31H 0B32H 0B33H 0B34H 0B35H 0B36H 0B37H 0B38H 0B39H 0B3AH
CALL FAILURE FROM OUTGOING CIRCUIT INTER-EXCHANGE SIGNALLING OUT OF ORDER ADDRESS COMPLETE MESSAGE TIME-OUT ADDRESS COMPLETE MESSAGE SENDING TIME EXCEEDED NO DIGITAL TRUNK NO ROUTE TO SPECIFIED TRANSIT OR TO DESTINATION NO CIRCUIT AVAILABLE IN TRANSIT NETWORK RESELECTION IN TRANSIT NETWORK APPLYING LOAD SHARING TRANSIT/TERMINAL SIGNAL WAIT TIMERSUPERVISION EXCEEDED LENGTH OF CHANGED CALLED SUBSCRIBER NUMBER EXCEEDED MODEM COMMUNICATION ERROR ADDRESS INCOMPLETE SERVICE UNAVAILABLE SERVICE INCOMPATIBLE NETWORK ADDRESS EXTENSION (NAE) ERROR DTE IS UNCONTROLLED DUAL SEIZURE FROM BIDIRECTIONAL CIRCUIT BLOCKING RECEIVED PARAMETER DOES NOT EXIST OR IS NOT IMPLEMENTED INTELLIGENT NETWORK APPLICATION RESPONSE INTELLIGENT NETWORK APPLICATION PROTOCOL ERROR TIME-OUT MAXIMUM NUMBER OF TRIGGERING EVENTS IN A CALL HAS BEEN REACHED TCAP ERROR ASN1 CODING OR DECODING ERROR SELECTIVE CALL CONGESTION HAS PREVENTED CALL ATTEMPT CALL RELEASE ORDERED BY INTELLIGENT NETWORK APPLICATION CONTINUITY CHECK FAILURE A-NUMBER IS NOT THE REGISTERED NUMBER OF AN INDIRECT SUBSCRIBER TOO MANY FRAUDULENT ATTEMPTS TO USE CALLING CARD CALLING CARD NUMBER SELECTED BY USER NOT FOUND IN-SERVICE INTERRUPTED FOR SUSPECTED FRAUD IN FALLBACK CODE ONE IN FALLBACK CODE TWO IN FALLBACK CODE THREE
20
Id:0900d80580635beb
0B3BH 0B3CH 0B3DH 0C00H 0C01H 0C02H 0C04H 0C05H 0C06H 0C08H 0C09H 0C0AH 0C0BH 0C0DH 0D00H 0D01H 0D03H 0D04H 0D06H 0D07H 0D08H 0D0BH 0D0FH 0D10H 0D11H
IN FALLBACK CODE FIVE IN FALLBACK CODE FOUR IN DIALOG - ROUTING FAILURE IN SS7 NETWORK DIAL WAIT TIME EXCEEDED PROHIBITED DIALLING INSUFFICIENT DIALLING FROM SUBSCRIBER SIGNALLING CALLING SUBSCRIBER HAS DIALLED WRONG KEYWORD CALLING SUBSCRIBER HAS NO RIGHT TO FACILITY CALLING SUBSCRIBER HAS NO RIGHT TO STORE NUMBER PREMATURE DIALLING SERVICE OR FACILITY ACTIVATION RESTRICTED SERVICE OR FACILITY USAGE RESTR USED INCONSISTENCY BETWEEN A- AND B-SUBSCRIBERS BEARER CAPABILITY NOT PRESENTLY AVAILABLE SUBSCRIBER SIGNALLING MESSAGE CONTENT SUBSCRIBER SIGNALLING MESSAGE FORMAT ERROR SERVICE OR FUNCTION NOT IMPLEMENTED SUBSCRIBER SIGNALLING PROTOCOL ERROR AOCC CHARGING ERROR NO RESPONSE TO CALL ESTABLISHMENT ALERTING OR CONNECT GSM ERH 4.08 PROTOCOL TIMER EXPIRES DUAL LOG-IN ISDN-SUBSCRIBER FACILITY DIALLING REJECTED MANDATORY INFORMATION ELEMENT MISSING INVALID INFORMATION ELEMENT CONTENT
Id:0900d80580635beb
21
Clear codes
5 Clear codes
5.1 000H - NORMAL END OF CALL
Text in MML printouts NORMAL END OF CALL Description An outgoing or incoming call has ended faultlessly. Detected by Default effect on the exchange Depending on the method of clearing, the call is cleared when either subscriber, or both of them have made onhook. Possibility to change the default effect Not possible. Alarms No alarms.
5.2
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible.
22
Id:0900d80580635beb
Clear codes
Alarms No alarms.
5.3
5.4
Id:0900d80580635beb
23
Clear codes
Alarms No alarms.
5.5
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a busy tone to the subscriber. Some subscriber services, e.g. Operator Intervention, may cause that the call set-up is continued. Possibility to change the default effect Using facility routing (command group RE, parameter CBB), the call can be directed for reanalysis in tree 33H both in terminal and transit exchanges. Besides this, facility routing can be used to connect an audible tone to the incoming circuit in terminal and transit exchanges. Alarms No alarms.
5.6
24
Id:0900d80580635beb
Clear codes
Forwarding on No Reply (CFNR) if the amount of call forwarding steps has been exceeded. Detected by
Program block CASSIG ICXPRB Explanation ICxPRB or CASSIG sets the clear code when the supervision time of the called subscriber's answer has been exceeded. ICXPRB or CASSIG sets the clear code when the supervision time of the called subscriber's answer has been exceeded.
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a busy tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.7
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
Id:0900d80580635beb
25
Clear codes
5.8
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.9
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a busy tone to the subscriber. Possibility to change the default effect Not possible.
26
Id:0900d80580635beb
Clear codes
Alarms No alarms.
5.10
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.11
Id:0900d80580635beb
27
Clear codes
Default effect on the exchange The call is cleared in transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.12
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange sends a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.13
28
Id:0900d80580635beb
Clear codes
Default effect on the exchange After call tracing, the call is continued as normal. Possibility to change the default effect Not possible. Alarms No alarms.
5.14
ICXPRB
TIGPRB
Id:0900d80580635beb
29
Clear codes
Default effect on the exchange The clear code is only used in successful intermediate reporting. No tone is connected to the subscriber, and the call is continued as normal. Possibility to change the default effect Not possible. Alarms No alarms.
5.15
Default effect on the exchange If, on the basis of incoming signalling information, the call can be rerouted from the incoming exchange, the call control clears the call backwards. The originating exchange carries out a digit re-analysis in standard analysis tree 26H (command group RE, parameter CAS). Possibility to change the default effect With facility routing it is possible to connect an audible tone to the subscriber. Alarms No alarms.
5.16
30
Id:0900d80580635beb
Clear codes
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.17
5.18
Id:0900d80580635beb
31
Clear codes
Text in MML printouts CALL TRANSFER RECALL Description The calling subscriber (A-subscriber), who has call transfer with recall facility, has transferred the call to a third party (C-subscriber), but the recall timer (C-subscriber answering time) has expired. The transferred call is cleared and the original call between the Asubscriber (the controlling subscriber) and the B-subscriber is re-established. Detected by Default effect on the exchange Possibility to change the default effect Not possible. Alarms No alarms.
5.19
5.20
32
Id:0900d80580635beb
Clear codes
Text in MML printouts CHA CAPA OF SUBS EXCEEDED Description The charging capacity of a subscriber has been exceeded in the exchange. Detected by Default effect on the exchange Possibility to change the default effect Not possible. Alarms No alarms.
5.21
5.22
Id:0900d80580635beb
33
Clear codes
Description In case of a successful interception announcement, the ICC sets the clear code ANN SUCCESS IN INTERCEPT (0020H) and sends it to statistics and charging. The initial disconnect clear code is always shown in call reports and in the unsuccessful call CDR if it is made. Detected by
Program block ICXPRB Explanation Either the IC1PRB, IC3PRB or IC6PRB sets this clear code when the interception announcement is given successfully.
Default effect on the exchange The call is cleared. If detailed charging (DC) is set in the interception tree, two clear codes are shown in the Call Detailed Charging report (CDR), the Subscriber Observation report (SO), and the trafficability performance reports. Otherwise only the initial clear code is shown. Possibility to change the default effect Not possible. Alarms No alarms.
5.23
ICXPRB
34
Id:0900d80580635beb
Clear codes
Default effect on the exchange This clear code is sent forward to the network. Possibility to change the default effect Not possible. Alarms No alarms.
5.24
Default effect on the exchange The originating exchange connects a tone or an announcement defined in EOS-analyse to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.25
Id:0900d80580635beb
35
Clear codes
Detected by
Program block STPROC Explanation STPROC sets the clear code when a reserved call record is subject to a new reservation.
Default effect on the exchange No effect on the call set-up. Possibility to change the default effect No effect on the call set-up. Alarms No alarms.
5.26
Default effect on the exchange No effect on the call set-up. Possibility to change the default effect No effect on the call set-up. Alarms No alarms.
5.27
36
Id:0900d80580635beb
Clear codes
Text in MML printouts CALL RECORD REL DURING CA Description When calibrating the traffic measurement files, the statistical program block has detected a circuit which is not included in the marker files even though the statistics files indicate that the circuit is seized. The statistics system releases the circuit. Detected by Default effect on the exchange No effect on the call set-up. Possibility to change the default effect No effect on the call set-up. Alarms No alarms.
5.28
5.29
Id:0900d80580635beb
37
Clear codes
Description The outgoing signalling has received an unknown line signal or an unknown message in reply to the seizure. Detected by
Program block CASSIG Explanation CASSIG sets the clear code when an unknown message is received in reply to the seizure.
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.30
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange sends a special information tone to the subscriber.
38
Id:0900d80580635beb
Clear codes
5.31
5.32
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Id:0900d80580635beb
39
Clear codes
5.33
Default effect on the exchange The call is cleared in transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.34
40
Id:0900d80580635beb
Clear codes
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.35
5.36
Id:0900d80580635beb
41
Clear codes
Detected by
Program block IC6PRB Explanation IC6PRB or INREGI (ARF) sets the clear code when there is no number created for the A-subscriber in the exchange.
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.37
5.38
42
Id:0900d80580635beb
Clear codes
Description The reason for release is either unknown or has previously been received (used in NUP signalling) or CCBS recall has not succeeded ( The called A subscriber does not answer ). Detected by
Program block CPLPRB SI4PRB Explanation CPLPRB sets the clear code when the called A subscriber does not answer during CCBS recall. SI4PRB sets the clear code when the reason for release has been received previously. CPLPRB sets the clear code when the called A subscriber does not answer during CCBS recall.
Default effect on the exchange The call is cleared in transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.39
Default effect on the exchange Possibility to change the default effect Not possible. Alarms No alarms.
Id:0900d80580635beb
43
Clear codes
5.40
Default effect on the exchange Possibility to change the default effect Not possible. Alarms No alarms.
5.41
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in the interception tree 32H.
44
Id:0900d80580635beb
Clear codes
Possibility to change the default effect Using facility routing (command group RE, parameter CCF) terminal and transit exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 32H. Using facility routing, the originating exchange can connect an audible tone to the calling subscriber. If the feature Call Drop Back is in use in the exchange, the call can be re-analysed in the desired tree set by the EOS Analysis Management -MML (command group RX). The redirecting number received in the release message from the network is used as the routing number. Alarms No alarms.
5.42
SI5PRB
Default effect on the exchange The call is cleared in terminal and transit exhanges. The originating exchange connects a congestion tone to a subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.43
Id:0900d80580635beb
45
Clear codes
Description Shows that the required subscriber line is not in service as a result of administrative action or at the request of the subscriber. Detected by
Program block SI4PRB Explanation
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects busy tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.44
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
46
Id:0900d80580635beb
Clear codes
5.45
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.46
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects busy tone to the subscriber. Possibility to change the default effect Not possible.
Id:0900d80580635beb
47
Clear codes
Alarms No alarms.
5.47
Default effect on the exchange SI7PRB (SSI) clears the call with ISUP REL cause code 112. Originating exchange connects special tone. Terminating exchange clears backwards with cause 112 Possibility to change the default effect Originating exchange can use facility routing or interception in tree 2AH. Alarms No alarms.
5.48
48
Id:0900d80580635beb
Clear codes
Detected by
Program block IC6PRB Explanation IC6PRB or INREGI sets the clear code when the call set-up is barred by subscriber-specific restriction of outgoing calls.
Default effect on the exchange The originating exchange connects a congestion tone to the subscriber. The clear code can only be set in the originating exchange. Possibility to change the default effect Using facility routing (command group RE, parameter CAB), the call can be directed for reanalysis in tree 35H both in terminal and transit exchanges, however, not in an exchange that has the A-validation feature. In A-validation cases a tone is connected to the calling subscriber. Alarms No alarms.
5.49
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
Id:0900d80580635beb
49
Clear codes
5.50
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree Possibility to change the default effect Using facility routing, an audible tone can be connected to the subscriber. Interception tree 35H (command group RE, parameter CAB). Interception tree 30H (command group RE, parameter CBO). Alarms No alarms.
5.51
50
Id:0900d80580635beb
Clear codes
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 2FH. Possibility to change the default effect Using facility routing (command group RE, parameter CFB), transit and terminal exchanges can carry out a digit re-analysis in tree 2FH, or connect an audible tone to the subscriber. Using facility routing, the originating exchange can connect an audible tone to the subscriber. Alarms No alarms.
5.52
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 35H. Possibility to change the default effect Using facility routing (command group RE, parameter CAB), the originating exchange and connect an audible tone to the subscriber, and terminal and transit exchanges can carry out a digit re-analysis in tree 35H, or connect an audible tone to the subscriber. Alarms No alarms.
5.53
Id:0900d80580635beb
51
Clear codes
Text in MML printouts B-NUMBER UNUSED Description The central memory's answer to the digit analysis is B-NUMBER UNUSED. Detected by
Program block ICXPRB Explanation ICxPRB or INREGI sets the clear code when information is received from the digit analysis that the analysed number is unused.
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 2AH. Possibility to change the default effect Using facility routing (command group RE, parameter CUN), terminal and transit exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 2AH. Using facility routing, the originating exchange can connect an audible tone to the subscriber. Alarms No alarms.
5.54
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 29H.
52
Id:0900d80580635beb
Clear codes
Possibility to change the default effect Using facility routing (command group RE, parameter CSN), terminal and transit exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 29H. Using facility routing, the originating exchange can connect an audible tone to the calling subscriber. Alarms No alarms.
5.55
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.56
Id:0900d80580635beb
53
Clear codes
Detected by
Program block SIXPRB Explanation SIxPRB or CASSIG sets the clear code when the calling subscriber makes onhook before the end-of-selection information is received.
Default effect on the exchange The call is cleared. An audible tone will not be connected because of subscriber onhook. Possibility to change the default effect Not possible. Alarms No alarms.
5.57
30BH - CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK WHEN WAITING FOR ANSWER
Text in MML printouts A ONHOOK DUR_WAIT ANSWER Description Onhook by the calling subscriber (A-subscriber) has taken place before the called subscriber (B-subscriber) has answered, or a signal or message equivalent to clearing has been received from the incoming circuit. Detected by
Program block SIXPRB Explanation CASSIG, SIxPRB or ICxPRB sets the clear code when, after the end-ofselection information has been received, the calling subscriber makes onhook before the called subscriber has answered.
Default effect on the exchange The call is cleared. An audible tone will not be connected because of subscriber onhook. Possibility to change the default effect Not possible. Alarms No alarms.
5.58
54
Id:0900d80580635beb
Clear codes
Text in MML printouts REANSWER TIME OUT Description The calling/called subscriber has not answered within the time supervision. Detected by
Program block ICXPRB Explanation CASSIG or ICxPRB sets the clear code if the subscriber has not reanswered within the time limit.
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a busy tone to the subscriber who has not made onhook. Possibility to change the default effect Not possible. Alarms No alarms.
5.59
Default effect on the exchange The call is cleared in terminal and transit exchanges. The terminating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible.
Id:0900d80580635beb
55
Clear codes
Alarms No alarms.
5.60
Default effect on the exchange The call is cleared in terminal and transit exchanges. In the originating exchange, a digit reanalysis is performed in the announcement tree. The originating exchange connects a congestion tone to the subscriber or performs reanalysis in the interception tree 35H. Possibility to change the default effect By using facility routing, the call can be directed for a reanalysis in an interception tree in both terminal and transit exchanges. In the originating exchange, an audible tone can be connected to the subscriber using facility routing, interception tree 2FH (command group RE, parameter CFB). Interception tree 35H (command group RE, parameter CAB). Alarms No alarms.
5.61
56
Id:0900d80580635beb
Clear codes
Detected by
Program block ICXPRB Explanation IC1PRB, IC3PRB, IC6PRB, INREGI
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange performs a reanalysis of the dialling using the tree 2BH (command group RE, parameter CNP). Possibility to change the default effect Using facility routing, the terminal and transit exchanges can perform a reanalysis of the dialling in the tree 2BH or connect an audible information tone to the subscriber. The originating exchange can connect an audible information tone to the subscriber using facility routing. Alarms No alarms.
5.62
5.63
Id:0900d80580635beb
57
Clear codes
Description The subscriber has not subscribed to the bearer service defined for the call, or the GSM BCIE is faulty. Detected by
Program block SI5PRB Explanation SI5PRB.
Default effect on the exchange The originating exchange carries out a digit re-analysis in tree 32H (command group RE, parameter CCF). The call is cleared in terminal and transit exchanges. Possibility to change the default effect Using facility routing, the originating exchange can connect an audible tone to the subscriber. Using facility routing (command group RE, parameter CST), terminal and transit exchanges can carry out a digit re-analysis in tree 34H. Alarms No alarms.
5.64
5.65
58
Id:0900d80580635beb
Clear codes
Text in MML printouts B HAS CALL DIVERS BARRING Description 1. Call diversion barring is set in the subscriber data of the called subscriber. 2. The number of diversions per call exceeds the set limit. Detected by
Program block OC6PRB Explanation OC6PRB or OUREGI sets the clear code when the call is diverted, but the subscriber data indicates that call diversion to the subscriber is not allowed. IC3PRB sets the clear code when call diversion involves a manual answering service.
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 35H. The originating exchange connects a congestion tone to the subscriber or performs reanalysis in the interception tree 35H. Possibility to change the default effect Using facility routing (command group RE, parameter CBB), the originating exchange can connect an audible tone to the subscriber. The terminal and transit exchanges can carry out a digit re-analysis in tree 35H, or connect an audible tone to the subscriber. Alarms No alarms.
5.66
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Id:0900d80580635beb
59
Clear codes
5.67
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.68
60
Id:0900d80580635beb
Clear codes
Detected by
Program block ICXPRB Explanation In a mobile terminating call, the IC1PRB, the IC2PRB or the IC3PRB sets this clear code if the HLR or the VLR returns information that the subscriber is not a member of the CUG. In a PBX terminating call, the OC1PRB sets this clear code if the called PBX is not a member of the CUG. The called party CUG check fails because the called party does not belong to the same CUG with the calling party, and the calling party does not use outgoing access or the called party does not have incoming access.
Default effect on the exchange Possibility to change the default effect Not possible. Alarms No alarms.
5.69
Default effect on the exchange Possibility to change the default effect Not possible. Alarms No alarms.
Id:0900d80580635beb
61
Clear codes
5.70
Default effect on the exchange Possibility to change the default effect Not possible. Alarms No alarms.
5.71
62
Id:0900d80580635beb
Clear codes
Detected by
Program block ICXPRB Explanation The IC2PRB sets this clear code if the VLR returns information that the closed user group index is unknown. The call is rejected because a calling subscriber makes the call with a CUG index which is unknown for the subscriber.
Default effect on the exchange Possibility to change the default effect Not possible. Alarms No alarms.
5.72
5.73
Id:0900d80580635beb
63
Clear codes
Detected by
Program block ASEPRB SREPRB Explanation
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.74
INREGI
Default effect on the exchange The call is cleared in transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
64
Id:0900d80580635beb
Clear codes
5.75
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.76
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible.
Id:0900d80580635beb
65
Clear codes
Alarms No alarms.
5.77
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.78
66
Id:0900d80580635beb
Clear codes
Detected by
Program block INREGI Explanation INREGI or OUREGI sets the clear code when SWICOP sends the 4130 or 4129 message in response, or when SCRPRB gives no response at all.
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.79
Id:0900d80580635beb
67
Clear codes
Explanation
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.80
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
68
Id:0900d80580635beb
Clear codes
5.81
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.82
Id:0900d80580635beb
69
Clear codes
Detected by
Program block RMAPRB Explanation RMAPRB sets the clear code when SWICOP returns the error code indicating that traffic type congestion has occurred in message congestion_on_route_s (4132). This occurs when selective circuit reservation or automatic congestion control rejection percentages cause the outgoing circuit reservation to fail. In both features the rejection percentages and continuation instructions for different traffic types (direct routed calls and alternatively directed calls) are defined. In selective circuit reservation the rejection percentages are applied after the user-defined threshold values have been reached. In automatic congestion control the rejection percentages are applied when the congestion level information has been received from the signalling point of the exchange to which the call is being routed.
Default effect on the exchange Possibility to change the default effect Not possible. Alarms No alarms.
5.83
Default effect on the exchange The call is released. Possibility to change the default effect Not possible.
70
Id:0900d80580635beb
Clear codes
Alarms 1206
5.84
5.85
Id:0900d80580635beb
71
Clear codes
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.86
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.87
72
Id:0900d80580635beb
Clear codes
Detected by
Program block OUREGI Explanation OUREGI (ARF) sets the clear code when the seizure of an outgoing circuit fails.
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 35H. Possibility to change the default effect Using facility routing (command group RE, parameter CAB), the originating exchange and connect an audible tone to the subscriber, and terminal and transit exchanges can carry out a digit re-analysis in tree 35H, or connect an audible tone to the subscriber. Alarms No alarms.
5.88
5.89
Id:0900d80580635beb
73
Clear codes
Description The activation or deactivation of a service has failed because there has been a failure in updating the service data in the central memory. Detected by
Program block OUREGI Explanation OUREGI sets the clear code when the activation of a facility fails in the ARF signalling because CMSUBS cannot update the facility data in the subscriber database.
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.90
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
74
Id:0900d80580635beb
Clear codes
5.91
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.92
Id:0900d80580635beb
75
Clear codes
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.93
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.94
76
Id:0900d80580635beb
Clear codes
Detected by
Program block ASEPRB Explanation The following program blocks set the clear code when a service request receives no response within the time limit; ASEPRB, CASSIG, CFOPRB, CPLPRB, GCAPRB, IC1PRB, IC3PRB, IC6PRB, IDOPRB, IDXSCP, INREGI, LHSPRB, OC1PRB, OC3PRB, OC6PRB, OUREGI, RMAPRB, SI1PRB, SI5PRB, SI6PRB, SI7PRB and TPSPRB.
CASSIG CFOPRB CPLPRB GCAPRB IC1PRB IC3PRB IC6PRB IDOPRB IDXSCP INREGI LHSPRB OC1PRB OC3PRB OC6PRB OUREGI RMAPRB SI1PRB SI5PRB SI6PRB SI7PRB TPSPRB
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.95
Id:0900d80580635beb
77
Clear codes
Text in MML printouts INT. CALL LINK CONGESTION Description No free internal call links are available. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.96
5.97
78
Id:0900d80580635beb
Clear codes
Description The polarity reversal relay is broken. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.98
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.99
Id:0900d80580635beb
79
Clear codes
Text in MML printouts CALL CLEARED BY MML Description The call has been cleared because of an operation and maintenance command. Detected by
Program block CASSIG SIXPRB Explanation CASSIG or SIxPRB sets the clear code when message forced_clear is received.
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.100
Default effect on the exchange The call is cleared in terminal, transit and originating exchanges. Possibility to change the default effect Not possible. Alarms No alarms.
80
Id:0900d80580635beb
Clear codes
5.101
5.102
5.103
Id:0900d80580635beb
81
Clear codes
Text in MML printouts MOD OR V5 FAIL CALL CLEAR Description A plug-in unit has broken down, or it has been removed from subscriber module SUBE, or the fault diagnosis has executed a forced test. Clear request has been received from the access node. SI2PRB sets this clear code if bearer channel is faulty due to access node internal failure. Detected by
Program block SI2PRB SI6PRB Explanation
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.104
82
Id:0900d80580635beb
Clear codes
5.105
INREGI
LHSPRB
OC6PRB
OUREGI
TPSPRB
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
Id:0900d80580635beb
83
Clear codes
5.106
INREGI
OUREGI
SI6PRB
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.107
84
Id:0900d80580635beb
Clear codes
Detected by
Program block INREGI OUREGI SI6PRB Explanation SI6PRB, INREGI or OUREGI sets the clear code when ACSERV sends the parity_err_from_pbru_mfcu or aux_mfc_parity_err message. SI6PRB, INREGI or OUREGI sets the clear code when ACSERV sends the parity_err_from_pbru_mfcu or aux_mfc_parity_err message.
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.108
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
Id:0900d80580635beb
85
Clear codes
5.109
5.110
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
86
Id:0900d80580635beb
Clear codes
5.111
5.112
Default effect on the exchange The exhange clears the call. A special tone is connected. Possibility to change the default effect Not possible.
Id:0900d80580635beb
87
Clear codes
Alarms No alarms.
5.113
5.114
88
Id:0900d80580635beb
Clear codes
5.115
5.116
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a busy tone to the subscriber. Possibility to change the default effect Using facility routing (command group RE, parameter CDP), the call can be directed for reanalysis in tree 2CH both in terminal and transit exchanges. Using facility routing, the originating exchange can connect an audible tone to the subscriber. Alarms 2225
Id:0900d80580635beb
89
Clear codes
5.117
Default effect on the exchange Call is disconnected. Possibility to change the default effect Not possible. Alarms 2300
5.118
90
Id:0900d80580635beb
Clear codes
Explanation IC1PRB, IC3PRB or IC6PRB set this code when tariff sent in CHGmessage is not accepted in originating or interworking exchange.
Default effect on the exchange Call is disconnected. Possibility to change the default effect Not possible. Alarms 2300
5.119
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Call continueing may be changed by EOS analysis management -MML. Alarms No alarms.
5.120
Id:0900d80580635beb
91
Clear codes
Detected by
Program block CMANAL Explanation The CMANAL returns this clear code when requested by the ICxPRB, if the digit analysis ended in congestion.
Default effect on the exchange The call is cleared. Possibility to change the default effect The parameters of the destination and subdestination can be redefined with the commands of the command groups RD, RK and RM. Alarms No alarms.
5.121
Default effect on the exchange Routing cannot be continued with the present requirements, but the call must be cleared. Possibility to change the default effect The call control process, ICxPRB, can set the required supplementary services as 'preferred', which means that the supplementary services are not obligatory, but this has to be done in the original call attempt. The commands of the command group RR can also be used to modify the supplementary services defined for the route. Alarms No alarms.
92
Id:0900d80580635beb
Clear codes
5.122
Default effect on the exchange Routing cannot be continued with the present requirements, but the call must be cleared. Possibility to change the default effect The call control process, ICxPRB, can set a secondary bearer capability requirement, which is used if the primary bearer capability could not be provided, but this has to be done in the original call attempt. The operator can also modify the bearer capability with the commands of the command group RR. Alarms No alarms.
5.123
Id:0900d80580635beb
93
Clear codes
code is not, however, used when the cause of the congestion can be expressed with the clear codes BEARER CAP NOT RECEIVED (0716H), FACIL NOT AVAIL ON ROUTE (0715H), PROHIBITED DIALLING (0C01H) or ATTRIBUTE GENERAL MISMATCH (0714H), or in analysis error situations, when the clear code is FILE ERROR (0509H). Detected by
Program block CMANAL Explanation The CMANAL returns this clear code when requested by the ICxPRB, if the digit analysis ended in congestion.
Default effect on the exchange Routing cannot be continued as the situation is irreversible, but the call must be cleared. Possibility to change the default effect The parameters of the destination and subdestination can be redefined with the commands of the command groups RD, RK and RM. Alarms No alarms.
5.124
94
Id:0900d80580635beb
Clear codes
Default effect on the exchange IC6PRB, IC1PRB and IC3PRB starts alternative routing. Possibility to change the default effect Not possible. Alarms 2668
5.125
Default effect on the exchange The call from an access is not accepted. Possibility to change the default effect Not possible. Alarms No alarms.
5.126
Id:0900d80580635beb
95
Clear codes
Detected by
Program block SI1PRB Explanation Detected by SI1PRB when the requested channel is not available (busy, not in use).
Default effect on the exchange A call from an access is not accepted. Possibility to change the default effect Not possible. Alarms No alarms.
5.127
Default effect on the exchange The exhange starts hunting for a new free circuit from the route. Possibility to change the default effect Not possible. Alarms No alarms.
5.128
96
Id:0900d80580635beb
Clear codes
Description Point-to-Point (PPP) Protocol has not been started or a failure in PPP-protocol has occured. Detected by
Program block MGAPRB Explanation MGAPRB sets the clear code according to the error information obtained from the Point-to-Point Protocol program block.
Default effect on the exchange The exhange clears the call. A special tone is connected. Possibility to change the default effect Not possible. Alarms No alarms.
5.129
5.130
Id:0900d80580635beb
97
Clear codes
Text in MML printouts A-NUMBER LENGTH EXCEEDED Description The calling subscriber's (A subscriber's) number is too long. The original calling subscriber's number received from the trunk circuit has been too long. Detected by
Program block INREGI Explanation INREGI sets the clear code when a too long A-subscriber number is received from R2 signalling.
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.131
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 32H.
98
Id:0900d80580635beb
Clear codes
Possibility to change the default effect Using facility routing (command group RE, parameter CCF), transit and terminal exchanges can carry out a digit re-analysis in tree 32H or connect an audible tone. Using facility routing, the originating exchange can connect an audible tone to the subscriber. Alarms No alarms.
5.132
INREGI SI2PRB
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree. Possibility to change the default effect By using facility routing, terminal and transit exchanges can carry out a digit re-analysis in interception tree or connect an audible tone. Interception tree 2DH (command group RE, parameter CFC). Alarms No alarms.
5.133
Id:0900d80580635beb
99
Clear codes
Description The identity of the calling subscriber (A-subscriber) has not been received from the incoming circuit. The termination of the call set-up phase requires the identity of the Asubscriber. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.134
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
100
Id:0900d80580635beb
Clear codes
5.135
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.136
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Id:0900d80580635beb
101
Clear codes
5.137
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.138
102
Id:0900d80580635beb
Clear codes
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree. Possibility to change the default effect Not possible. Interception tree 2EH. Alarms No alarms.
5.139
5.140
Id:0900d80580635beb
103
Clear codes
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in an interception tree. Possibility to change the default effect Using facility routing, terminal and transit exchanges can carry out a digit re-analysis in an interception tree or connect an audible tone. Using facility routing, the originating exchange can connect an audible tone to the subscriber. Interception tree 2DH (command group RE, parameter CFC). Interception tree 32H (command group RE, parameter CCF). Alarms No alarms.
5.141
5.142
104
Id:0900d80580635beb
Clear codes
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 2DH (command group RE, parameter CFC). Possibility to change the default effect Using facility routing, terminal and transit exchanges can carry out a digit re-analysis in tree 2DH or connect an audible tone. Using facility routing, the originating exchange can connect an audible tone to the subscriber. Alarms No alarms.
5.143
5.144
Id:0900d80580635beb
105
Clear codes
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree. Possibility to change the default effect Using facility routing terminal and transit exchanges can carry out a digit re-analysis in interception tree or connect an audible tone. Using facility routing, the originating exchange can connect an audible tone to the subscriber. Interception tree 2EH (command group RE, parameter CRO). Interception tree 2DH (command group RE, parameter CFC). Alarms No alarms.
5.145
5.146
106
Id:0900d80580635beb
Clear codes
Description Information "send special information tone" has been received from the network. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 34H. Possibility to change the default effect Using facility routing (command group RE, parameter CST), the call can be directed for reanalysis in tree 34H both in terminal and transit exchanges. Using facility routing, the originating exchange can connect an audible tone to the subscriber. Alarms No alarms.
5.147
5.148
Id:0900d80580635beb
107
Clear codes
Description Information "line out of service or unallocated" has been received from the network. SI2PRB sets this clear code: in V5 interface congestion if state or user port is not available or bearer channel reservation fails. Detected by
Program block SI2PRB SI6PRB Explanation SI2PRB, SI6PRB
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree. Possibility to change the default effect Using facility routing the terminal and transit exchanges can carry out a digit re-analysis in interception tree or connect an audible tone. Using facility routing, the originating exchange can connect an audible tone to the subscriber. Interception tree 2FH (command group RE, parameter CFB). Alarms No alarms.
5.149
108
Id:0900d80580635beb
Clear codes
5.150
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.151
Id:0900d80580635beb
109
Clear codes
5.152
5.153
SI7PRB
Default effect on the exchange The call is rerouted to an alternative route. If it is not possible, the call is cleared with this clear code. The function to the network depends on the signalling used. Possibility to change the default effect Not possible.
110
Id:0900d80580635beb
Clear codes
Alarms No alarms.
5.154
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.155
Id:0900d80580635beb
111
Clear codes
5.156
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a busy tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.157
112
Id:0900d80580635beb
Clear codes
Explanation
Default effect on the exchange The call from an access is not accepted. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms 2202, 2204, 2900, 2902, 2909, 2910, 2912, 2915
5.158
Default effect on the exchange The call is cleared in the terminal and transit exchanges. The originating exchange connects an announcement or an audible tone to the subscriber. Possibility to change the default effect Using facility routing, the terminal and transit exchanges can carry out a digit re-analysis in the interception tree 32H (command group RE, parameter CCF). Alarms No alarms.
Id:0900d80580635beb
113
Clear codes
5.159
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree. Possibility to change the default effect By using facility routing, the terminal and transit exchanges can carry out a digit reanalysis in an interception tree or connect an audible tone. Interception tree 2DH (command group RE, parameter CFC). Alarms No alarms.
5.160
114
Id:0900d80580635beb
Clear codes
Detected by
Program block INXPRB SI1PRB SI7PRB Explanation SI7PRB SI1PRB INXPRB
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree 32H. Possibility to change the default effect Using facility routing terminal and transit exchanges can carry out a digit re-analysis in the interception tree 32H ( command group RE, parameter CCF ) or connect an audible tone to the subscriber. Using facility routing the originating exchange can connect an audible tone to the subscriber. Using EOS -analysis handling ( MML command group RX ) the analysis tree can be changed. Alarms No alarms.
5.161
Default effect on the exchange The call is released. Possibility to change the default effect Not possible. Alarms 1206
Id:0900d80580635beb
115
Clear codes
5.162
Default effect on the exchange The call is cleared. An announcement or a tone is connected to the subscriber. Possibility to change the default effect Using facility routing, terminal and transit exchanges can carry out a digit re-analysis or connect an audible tone. Using facility routing, the originating exchange can connect an audible tone to the subscriber. Interception tree 2DH (command group RE, parameter CFC). Alarms 2997
5.163
116
Id:0900d80580635beb
Clear codes
Detected by
Program block SI7PRB Explanation
Default effect on the exchange This causes clearing of call, and no repeat attempts are allowed. Possibility to change the default effect Not possible. Alarms No alarms.
5.164
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.165
Id:0900d80580635beb
117
Clear codes
Description In multifrequency signalling, an MF signal with a duration of >= 1 - 2 s has been received from the incoming circuit. Detected by
Program block INREGI Explanation INREGI sets the clear code when ACSERV sends message aux_long_char_s (6540).
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.166
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
118
Id:0900d80580635beb
Clear codes
5.167
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.168
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Id:0900d80580635beb
119
Clear codes
5.169
5.170
120
Id:0900d80580635beb
Clear codes
Alarms No alarms.
5.171
5.172
Id:0900d80580635beb
121
Clear codes
Alarms No alarms.
5.173
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 34H. Possibility to change the default effect Using facility routing (command group RE, parameter CST), the terminal or transit exchanges can connect an audible tone to the incoming circuit or carry out a digit reanalysis in tree 34H. Using facility routing, the originating exchange can connect an audible tone to the subscriber. Alarms No alarms.
5.174
122
Id:0900d80580635beb
Clear codes
Detected by
Program block SI5PRB SI7PRB Explanation SI5PRB or SI7PRB sets the clear code when it receives the message RSC (reset-circuit message).
Default effect on the exchange The outgoing circuit is hunted again. The signalling record indicates how many times the circuit is hunted in a call. Possibility to change the default effect Not possible. Alarms No alarms.
5.175
5.176
Id:0900d80580635beb
123
Clear codes
Text in MML printouts DESTINATI POINT CONGESTI Description After it has received a seizure, the program block which supervises the outgoing interexchange signalling has found a temporary disturbance in the signalling of the hunted trunk circuit. Detected by
Program block SI5PRB Explanation SI5PRB sets the clear code when no acknowledgement is received from the signalling within the time supervision limit.
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. The originating exchange connects a special information tone to the subscriber or performs reanalysis in the interception tree 34H. Possibility to change the default effect Using facility routing (command group RE, parameter CST), the call can be directed for reanalysis in tree 34H both in terminal and transit exchanges. Alarms No alarms.
5.177
124
Id:0900d80580635beb
Clear codes
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.178
5.179
Id:0900d80580635beb
125
Clear codes
Detected by
Program block INREGI Explanation INREGI sets the clear code when the digit analysis ends in congestion, and the call has requested a digital connection.
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber ( call from PABX ) or performs reanalysis in the interception tree 36H ( call from subscriber ). Possibility to change the default effect Using facility routing (command group RE, parameter CDN), the call can be directed for reanalysis in tree 36H both in terminal and transit exchanges. Alarms No alarms.
5.180
5.181
126
Id:0900d80580635beb
Clear codes
Text in MML printouts NO CIRCUIT IN TRANS NW Description No circuits available in the transit network. Detected by
Program block SI7PRB Explanation Detected by SI7PRB if the release message received from network is the national Belgian ISUP cause code #13.
Default effect on the exchange Possibility to change the default effect Not possible. Alarms No alarms.
5.182
Default effect on the exchange Possibility to change the default effect Not possible. Alarms No alarms.
Id:0900d80580635beb
127
Clear codes
5.183
Default effect on the exchange The call is cleared in the terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.184
128
Id:0900d80580635beb
Clear codes
Alarms No alarms.
5.185
Default effect on the exchange The exhange clears the call. Special tone is connected. Possibility to change the default effect Not possible. Alarms No alarms.
5.186
Id:0900d80580635beb
129
Clear codes
Possibility to change the default effect Using facility routing, the transit and terminal exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 2CH. Using facility routing, the originating exchange can connect an audible tone to the subscriber. Alarms No alarms.
5.187
5.188
130
Id:0900d80580635beb
Clear codes
5.189
5.190
Id:0900d80580635beb
131
Clear codes
Alarms No alarms.
5.191
5.192
Default effect on the exchange The outgoing circuit is hunted again. The number of hunting attempts is indicated in the outgoing signalling record.
132
Id:0900d80580635beb
Clear codes
5.193
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.194
Id:0900d80580635beb
133
Clear codes
Detected by
Program block ICXPRB Explanation ICxPRB (inif_t) sets the clear code when an error is detected in the IN protocol.
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.195
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
134
Id:0900d80580635beb
Clear codes
5.196
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.197
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Id:0900d80580635beb
135
Clear codes
5.198
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.199
136
Id:0900d80580635beb
Clear codes
5.200
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.201
Id:0900d80580635beb
137
Clear codes
Explanation
Default effect on the exchange The outgoing circuit is hunted again. The amount of hunting attempts is indicated in the outgoing signalling record. Possibility to change the default effect Not possible. Alarms No alarms.
5.202
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.203
138
Id:0900d80580635beb
Clear codes
Description There have been too many fraudulent attempts to use a calling card. Therefore its use is temporarily prevented. Detected by
Program block IDXSCP Explanation
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.204
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
Id:0900d80580635beb
139
Clear codes
5.205
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.206
Default effect on the exchange The Incoming Call Control detects an IN trigger detection point.
140
Id:0900d80580635beb
Clear codes
Possibility to change the default effect The PRFILE parameter IN_FALLBACK_SSET_INDEX controls the action. Any value different from 0 starts a new IN session. Otherwise the call is cleared. Alarms No alarms.
5.207
Default effect on the exchange The Incoming Call Control detects an IN trigger detection point. Possibility to change the default effect The PRFILE parameter IN_FALLBACK_SSET_INDEX controls the action. Any value different from 0 starts a new IN session. Otherwise the call is cleared. Alarms No alarms.
5.208
Id:0900d80580635beb
141
Clear codes
Default effect on the exchange Incoming Call Control is detecting an IN trigger detection Point. Possibility to change the default effect The PRFILE parameter IN_FALLBACK_SSET_INDEX is controlling the action. A value different from 0 gives start to a new IN session. Otherwise the call is cleared. Alarms No alarms.
5.209
Default effect on the exchange Incoming Call Control is detecting an IN trigger detection Point. Possibility to change the default effect The PRFILE parameter IN_FALLBACK_SSET_INDEX is controlling the action. A value different from 0 gives start to a new IN session. Otherwise the call is cleared. Alarms No alarms.
142
Id:0900d80580635beb
Clear codes
5.210
Default effect on the exchange Incoming Call Control is detecting an IN trigger detection Point. Possibility to change the default effect The PRFILE parameter IN_FALLBACK_SSET_INDEX is controlling the action. A value different from 0 gives start to a new IN session. Otherwise the call is cleared. Alarms No alarms.
5.211
Id:0900d80580635beb
143
Clear codes
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree 34H or connects an audible tone. Possibility to change the default effect By using facility routing, terminal and transit exchanges can carry out a digit re-analysis in interception tree or connect an audible tone. Interception tree 34H (command group RE, parameter CST). Alarms 2617
5.212
INREGI
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber or performs reanalysis in the interception tree 2CH. Possibility to change the default effect Not possible. Alarms No alarms.
5.213
144
Id:0900d80580635beb
Clear codes
Detected by
Program block ICXPRB INREGI Explanation ICxPRB or INREGI sets the clear code when digit analysis has resulted in congestion. ICxPRB or INREGI sets the clear code when digit analysis has resulted in congestion.
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree. Possibility to change the default effect Using facility routing transit and terminal exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in interception tree 2CH (command group RE, parameter CDP). Using facility routing, the originating exchange can connect an audible tone to the subscriber. Alarms No alarms.
5.214
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 2CH (command group RE, parameter CDP). Possibility to change the default effect Using facility routing, the transit and terminal exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 2CH. Using facility routing, the originating exchange can connect an audible tone to the subscriber.
Id:0900d80580635beb
145
Clear codes
Alarms No alarms.
5.215
5.216
146
Id:0900d80580635beb
Clear codes
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.217
OUREGI
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.218
Id:0900d80580635beb
147
Clear codes
Text in MML printouts PREMATURE DIALLING Description The subscriber has dialled during a register wait state, i.e. before hearing the dial tone, or there are disturbances on the subscriber line. The call set-up is interrupted. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.219
148
Id:0900d80580635beb
Clear codes
5.220
5.221
Id:0900d80580635beb
149
Clear codes
Possibility to change the default effect Using facility routing the call can be directed for reanalysis in interception tree both in terminal and transit exchanges. In the originating exchange an audible tone can be connected to the subscriber using facility routing. Interception tree 35H (command group RE, parameter CAB). Interception tree 32H (command group RE, parameter CCF). Alarms No alarms.
5.222
Default effect on the exchange Possibility to change the default effect Not possible. Alarms No alarms.
5.223
150
Id:0900d80580635beb
Clear codes
scriber terminal. This clear code is used also when encountering an illogical or erroneous subscriber signalling message. Detected by
Program block SI6PRB Explanation SI6PRB sets the clear code when unknown values are received in network messages.
Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.224
5.225
Id:0900d80580635beb
151
Clear codes
Text in MML printouts SERV OR FUNC NOT IMPLEM Description A service or a function requested by the subscriber has not been implemented in the exchange. Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 36H (command group RE, parameter CDN). Possibility to change the default effect Not possible. Alarms No alarms.
5.226
5.227
152
Id:0900d80580635beb
Clear codes
Text in MML printouts AOCC CHARGING ERROR Description The call has been cleared because the mobile station which has been equipped with AOC-C (Advice of Charge, Charging) supplementary service does not acknowledge the Charge Advice Information (CAI). Detected by Default effect on the exchange The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. Possibility to change the default effect Not possible. Alarms No alarms.
5.228
SI6PRB
Default effect on the exchange The call is cleared in transit and terminal exchanges. The originating exchange connects a busy tone to the subscriber.
Id:0900d80580635beb
153
Clear codes
Possibility to change the default effect Using facility routing (command group RE, parameter CCF), the call can be directed for reanalysis in tree 32H both in terminal and transit exchanges. Interception tree 33H (command group RE, parameter CBB). Alarms No alarms.
5.229
5.230
154
Id:0900d80580635beb
Clear codes
Alarms No alarms.
5.231
Default effect on the exchange Call is disconnected with tone or announcement. Possibility to change the default effect Not possible. Alarms No alarms.
5.232
Id:0900d80580635beb
155
Clear codes
Default effect on the exchange The message (SETUP) is not accepted and the call is cleared. Possibility to change the default effect Not possible. Alarms No alarms.
5.233
Default effect on the exchange A call from an access is not accepted. Possibility to change the default effect Not possible. Alarms No alarms.
156
Id:0900d80580635beb
Id:0900d80580635beb
157
NUMBER 020FH 0210H 0211H 0213H 0215H 0216H 0217H 0218H 0219H 0220H 0252H 0300H 0301H 0304H 0305H 0306H 0307H 0308H 0309H 030AH 030BH 030CH 030DH 030EH 030FH 0310H 0311H 0312H 0315H 0317H 031AH 031CH 031DH 0321H 0322H 0400H 0401H
NAME CHANGE OF OUTGOING CIRCUIT NULL NUP NETWORK, REJECTED DIVERTED CALLS NETWORK, USER NOT IN CUG CALL DROP BACK MISDIALLED TRUNK PREFIX TEMPORARY OUT OF ORDER OUT OF CATCHMENT AREA TRANSLATION OUT-OF-SERVICE ANONYMOUS CALLS REJECTION UNTERMINATED CALL TO A PORTED NUMBER CALLING SUBSCRIBER BARRED DUE TO RESTRICTION IN THE OUTGOING DIRECTION CALLING SUBSCRIBER'S OUTGOING CALL RESTRICTED BY OPERATOR CALLED SUBSCRIBER LINE OUT OF SERVICE CALLED SUBSCRIBER LINE FAULTY ACCESS TO B-SUBSCRIBER LINE RESTRICTED B-NUMBER UNUSED B-NUMBER CHANGED TIME-OUT WHEN WAITING FOR OPERATOR'S INTERVENTION CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK DURING SET-UP PHASE CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK WHEN WAITING FOR ANSWER REANSWER TIME OUT B- OR C-NUMBER IS NOT REGISTERED CALLED SUBSCRIBER LINE BLOCKED CHANGE IN NUMBERING PLAN CLOSED USER GROUP RESCTRICTION BEARER SERVICE NOT PROVIDED TELESERVICE NOT PROVIDED CALLED SUBSCRIBER HAS CALL DIVERSION BARRING TIME-OUT IN INTELLIGENT NETWORK BASED SUBSCRIBER SERVICE INCOMING CALLS BARRED WITHIN THE CUG SUBSCRIBER NOT A MEMBER OF THE CUG OUTGOING CALLS BARRED WITHIN THE CUG NO CUG SELECTED UNKNOWN CUG INDEX ATTENUATOR CONGESTION INTERWORKING UNIT CONGESTION
158
Id:0900d80580635beb
NUMBER 0402H 0403H 0404H 0405H 0406H 0407H 0408H 0409H 040AH 040BH 0506H 0508H 0509H 050BH 050CH 050DH 050FH 0600H 0601H 0602H 0603H 0604H 0606H 0607H 0608H 0609H 060BH 060DH 060EH 060FH 0700H 0701H 0702H 0704H 0705H 0706H 0707H 070AH
NAME REGISTER TOTAL TIME EXCEEDED MFCU DEVICE CONGESTION PBRU DEVICE CONGESTION ERRONEOUS SERVICE REQUEST FROM CO-PROCESS CONNECTION FAILED IN GSW/SWI ERRONEOUS ANSWER FROM PARTNER PROGRAM BLOCK LENGTH OF CALLED SUBSCRIBER NUMBER EXCEEDED CONNECTION FAILED IN SSW/SWI CIRCUIT CONGESTION DUE TO TRAFFIC TYPE HOP COUNTER EXHAUST LINES OF LINE HUNTING GROUPS BARRED CHARGING ERROR FILE ERROR MODULE ROUTE OR SSW CONGESTION MFC-ASS-CHANNEL CLOSING MISSED FACILITY CONTROL FAILED UNSUITABLE MODULE CIRCUIT FILE RECORD CONGESTION MODULE OR V5 CONGESTION REGISTER CONGESTION NO RESPONSE FROM PARTNER PROGRAM BLOCK INTERNAL CALL LINK CONGESTION CONFERENCE DEVICE CONGESTION POLARITY REVERSAL FAILURE CHARGING NOT STARTED CALL CLEARED BY MML OVERLOAD CONGESTION STAGE CIRCUIT CONGESTION UNIT RESTARTED SUBSCRIBER MODULE OR V5 INTERFACE FAILURE, CALL CLEARED LONG AON REQUEST REGISTER ANALYSIS FAILED QUEUEING TIME EXCEEDED PARITY ERROR FROM PBRU/MFCU DEVICE MODULE OR V5 INTERFACE NOT AVAILABLE CALL INTERRUPTED DURING REGISTER ANALYSIS SUBSCRIBER MODULE RESTARTED FORCED CLEAR OF A CALL
Id:0900d80580635beb
159
NUMBER 070BH 070CH 070DH 070EH 0710H 0711H 0712H 0713H 0714H 0715H 0716H 0718H 0719H 071AH 071BH 071CH 071DH 0801H 0802H 0803H 0804H 0806H 0809H 080AH 080BH 080CH 080DH 080EH 080FH 0810H 0811H 0813H 0814H 0815H 0816H 0817H 0818H 0819H
NAME MODEM ERROR OVERLOAD CONTROL SYSTEM ERROR ANNOUNCEMENT SERVICE FAILURE CONFIGURATION ERROR NO ANALYSIS FOR CARRIER ACCESS CODE TARIFF NOT ACCEPTED BY TRANSIT EXCHANGE TARIFF NOT ACCEPTED BY ORIGINATING OR INTERWORKING EXCHANGE NO ISUP ROUTE ATTRIBUTE DIRECTED ROUTING MISMATCH REQUESTED FACILITY WAS NOT AVAILABLE ON THE OUTGOING ROUTE REQUESTED BEARER CAPABILITY COULD NOT BE FULFILLED ON THE ROUTE DIGIT ANALYSIS IN CENTRAL MEMORY RESULTED IN CONGESTION NO RESOURCE AVAILABLE FOR CALL IDENTIFIED CHANNEL NOT EXIST REQUESTED CHANNEL NOT AVAILABLE PACKET CONTROL UNIT CONGESTION POINT-TO-POINT PROTOCOL ERROR LENGTH OF ORIGINAL CALLED SUBSCRIBER NUMBER EXCEEDED LENGTH OF CALLING SUBSCRIBER NUMBER EXCEEDED INVALID CALLING SUBSCRIBER CATEGORY OUTGOING CIRCUIT CONGESTION IDENTITY OF CALLING SUBSCRIBER IS NOT AVAILABLE ERRONEOUS MFC SIGNAL FROM OUTGOING CIRCUIT ERRONEOUS MFC SIGNAL FROM INCOMING CIRCUIT NO B-NUMBERS TO SEND TO OUTGOING CIRCUIT UNKNOWN DECADIC SIGNAL FROM INCOMING CIRCUIT OUTGOING CIRCUIT OUT OF ORDER INCOMING CIRCUIT OUT OF ORDER CIRCUIT CONGESTION FACILITY NOT SUPPORTED NETWORK FAILURE SWITCHING EQUIPMENT CONGESTION CIRCUIT GROUP CONGESTION ACCESS BARRED TO THE CALLED SUBSCRIBER CALL FAILED, SEND SPECIAL INFORMATION TONE NETWORK, UNALLOCATED NUMBER NETWORK, LINE OUT OF SERVICE NETWORK, SUBSCRIBER NUMBER CHANGED
160
Id:0900d80580635beb
NUMBER 081AH 081DH 081EH 081FH 0820H 0821H 0822H 0824H 0828H 0829H 0830H 0832H 0833H 0851H 0900H 0901H 0905H 090CH 090EH 090FH 0A01H 0A02H 0A03H 0A04H 0A05H 0A07H 0A08H 0A09H 0A0AH 0A0CH 0A0DH 0A0EH 0A0FH 0B02H 0B0FH 0B11H 0B17H
NAME CONGESTION IN TERMINAL EXCHANGE CONGESTION IN INTERNATIONAL CALL CONTROLLED NOT READY NETWORK, OVERLOAD CONGESTION NETWORK MESSAGE CONTENT ERROR INVALID TRANSIT NETWORK SELECTION RECOVERY ON TIMER EXPIRY PCM FAULTY CONGESTION FROM NATIONAL NETWORK DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT CONGESTION NUMBER PORTABILITY ROUTING ERROR DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT FAILURE TRAFFIC TO CONGESTED DESTINATION POINT CODE RESTRICTED BY SIGNALLING NO MF FORWARD SIGNAL TOO LONG MF FORWARD SIGNAL TOO LONG MF BACKWARD SIGNAL PREMATURE ACKNOWLEDGEMENT TO SEIZURE IN OUTGOING CIRCUIT PREMATURE ANSWER ANSWER AFTER B BUSY CLEARED FORWARD (SEIZING ACKNOWLEDGED SIGNAL MISSING) INVALID MESSAGE FROM TRUNK CIRCUIT INTERWORKING FAILED TRUNK CIRCUIT PROTOCOL ERROR CIRCUIT RELEASED BY CO-EXCHANGE CALL FAILURE FROM OUTGOING CIRCUIT INTER-EXCHANGE SIGNALLING OUT OF ORDER ADDRESS COMPLETE MESSAGE TIME-OUT ADDRESS COMPLETE MESSAGE SENDING TIME EXCEEDED NO DIGITAL TRUNK NO ROUTE TO SPECIFIED TRANSIT OR TO DESTINATION NO CIRCUIT AVAILABLE IN TRANSIT NETWORK RESELECTION IN TRANSIT NETWORK APPLYING LOAD SHARING TRANSIT/TERMINAL SIGNAL WAIT TIME SUPERVISION EXCEEDED LENGTH OF CHANGED CALLED SUBSCRIBER NUMBER EXCEEDED MODEM COMMUNICATION ERROR ADDRESS INCOMPLETE
Id:0900d80580635beb
161
NUMBER 0B18H 0B19H 0B20H 0B21H 0B23H 0B2AH 0B2BH 0B2CH 0B2DH 0B2EH 0B2FH 0B30H 0B31H 0B32H 0B33H 0B34H 0B35H 0B36H 0B37H 0B38H 0B39H 0B3AH 0B3BH 0B3CH 0B3DH 0C00H 0C01H 0C02H 0C04H 0C05H 0C06H 0C08H 0C09H 0C0AH 0C0BH 0C0DH 0D00H 0D01H
NAME SERVICE UNAVAILABLE SERVICE INCOMPATIBLE NETWORK ADDRESS EXTENSION (NAE) ERROR DTE IS UNCONTROLLED DUAL SEIZURE FROM BIDIRECTIONAL CIRCUIT BLOCKING RECEIVED PARAMETER DOES NOT EXIST OR IS NOT IMPLEMENTED INTELLIGENT NETWORK APPLICATION PROTOCOL ERROR INTELLIGENT NETWORK APPLICATION RESPONSE TIME-OUT MAXIMUM NUMBER OF TRIGGERING EVENTS IN A CALL HAS BEEN REACHED TCAP ERROR ASN1 CODING OR DECODING ERROR SELECTIVE CALL CONGESTION HAS PREVENTED CALL ATTEMPT CALL RELEASE ORDERED BY INTELLIGENT NETWORK APPLICATION CONTINUITY CHECK FAILURE A-NUMBER IS NOT THE REGISTERED NUMBER OF AN INDIRECT SUBSCRIBER TOO MANY FRAUDULENT ATTEMPTS TO USE CALLING CARD CALLING CARD NUMBER SELECTED BY USER NOT FOUND IN-SERVICE INTERRUPTED FOR SUSPECTED FRAUD IN FALLBACK CODE ONE IN FALLBACK CODE TWO IN FALLBACK CODE THREE IN FALLBACK CODE FIVE IN FALLBACK CODE FOUR IN DIALOG - ROUTING FAILURE IN SS7 NETWORK DIAL WAIT TIME EXCEEDED PROHIBITED DIALLING INSUFFICIENT DIALLING FROM SUBSCRIBER SIGNALLING CALLING SUBSCRIBER HAS DIALLED WRONG KEYWORD CALLING SUBSCRIBER HAS NO RIGHT TO FACILITY CALLING SUBSCRIBER HAS NO RIGHT TO STORE NUMBER PREMATURE DIALLING SERVICE OR FACILITY ACTIVATION RESTRICTED SERVICE OR FACILITY USAGE RESTRICTED INCONSISTENCY BETWEEN A- AND B-SUBSCRIBERS BEARER CAPABILITY NOT PRESENTLY AVAILABLE SUBSCRIBER SIGNALLING MESSAGE CONTENT ERROR SUBSCRIBER SIGNALLING MESSAGE FORMAT ERROR
162
Id:0900d80580635beb
NUMBER 0D03H 0D04H 0D06H 0D07H 0D08H 0D0BH 0D0FH 0D10H 0D11H
NAME SERVICE OR FUNCTION NOT IMPLEMENTED SUBSCRIBER SIGNALLING PROTOCOL ERROR AOCC CHARGING ERROR NO RESPONSE TO CALL ESTABLISHMENT: ALERTING OR CONNECT GSM ERH 4.08 PROTOCOL TIMER EXPIRES DUAL LOG-IN ISDN-SUBSCRIBER FACILITY DIALLING REJECTED MANDATORY INFORMATION ELEMENT MISSING INVALID INFORMATION ELEMENT CONTENT
Id:0900d80580635beb
163
Glossary
Glossary
AOC-C ASN.1 BCIE CAC CAI CCSU CFU CFB CFNR CUG DTE EIR HLR ISUP ITUP IN ICxPRB MFC MFCU MFST MWD NUP PBRU PCM PNP SCP SSP TCAP TUP VLR Advice of Charge (charging) Abstract Syntax Notation One Bearer Capability Information Element Carrier Access Code Charge Advice Information Common Channel Signalling Unit Call Forwarding Unconditional Call Forwarding Busy Call Forwarding On No Reply Closed User Group Data Terminal Equipment Equipment Identity Register DX HLR ISDN User Part International Telephone User Part Intelligent Network IC1PRB, IC2PRB, IC3PRB and IC9PRB Multifrequency Code Multifrequency Code Unit Multi Frequency Signalling Terminal plug-in unit Messages Waiting Data National User Part Push Button Receiver Unit Pulse Code Modulation Private Numbering Plan Service Control Point Service Switching Point Transaction Capabilities Application Part Telephone User Part Visitor Location Register
164
Id:0900d80580635beb