Beruflich Dokumente
Kultur Dokumente
0
Geometric angle of attack
eff
Eective angle of attack
a Motion amplitude mm
C(k) Theodorsen function
C
D
D
1/2SU
Drag coecient
C
L
L
1/2SU
Lift coecient
c Wing chord mm
D Drag N
E Youngs modulus Mpa
Reduced frequency
h/c Non-dimensional ground clearance
h Wing position
h
a
c
Non-dimensional motion amplitude
L Lift N
q Freestream dynamic pressure Pa
M
U
c
Mach number
P
x
Propulsive power W
viii
LIST OF FIGURES
Phase shift
Re
U
Reynolds Number
Flow density
S Planform area m
2
Standard deviation
t Time s
Tu
u
2
U
Turbulence intensity
U
W Weight kg
W Average power W
y Half length of the strut mm
ix
LIST OF FIGURES
x
1
Introduction
Without any doubt, the best researcher in the world is Nature itself. There is
not a more decisive incentive for improvement and advancement than the quest
for survival, which requires animals, and most of the living creatures, to be-
come faster, stronger, tougher as time goes by, and while Nature itself, with
the evolutionary process, provides their predators with increasingly powerful and
dangerous weapons to ultimately kill them. This mechanism is not unlike any
sport, where the smallest detail can make the dierence between winning and
losing, rather than living or dying.
It is therefore sensible to look with curious and inquisitive eye at what Nature
shows us, and try to extract all the lessons we can. In science and engineering
especially, Nature can represent an incredible and invaluable source of inspiration
and provide the basis for technological breakthroughs. Fluid mechanics makes no
exception, as the rst to gain an insight from biological creatures was arguably
Leonardo da Vinci himself, who tried, somehow successfully, to reproduce the
wing of a bird and to understand the mechanisms that allow such beautiful crea-
tures to y and glide. Nowadays, many features of living creatures are being
studied in an attempt to improve both our knowledge and our resource man-
agement; for what concerns uids, it is valuable to mention the studies on the
compliant surfaces of dolphins (1) (2) (3), rough surfaces (riblets) on sharks (4)
(5) (6), wavy leading edges on whales (7) (8) (9) (10), and the overall dynamics
of ight, from the sheer speed of the peregrine falcon to the gracious nimbleness
of the swallow.
1
1. INTRODUCTION
Regarding biological ight, many attempts have been made to comprehend and
reproduce it in laboratory, both from a dynamical and structural point of view.
For the former, it is possible to state that the wing motion for a bird is a combi-
nation of heaving, pitching and fore-aft motion, commonly referred as apping.
Applications of these ndings range from nano-UAVs (Unmanned Aerial Vehi-
cles), to small MAVs (Micro Aerial Vehicles) and larger-sized UAVs; recently, the
inuence of these types of motion has been studied in relation with even larger
structures, including racing cars, with the nal aim of improving eciency and
performance.
1.1 Background and Motivations
The inuence of aerodynamics in the design of racing cars has steadily increased
in the last decades, and, nowadays, is doubtlessly the most inuential factor for
performance. The front wing is one of the most important devices on the entire
car, and is responsible for the production of downforce, as well as being the only
element to encounter freestream conditions. The wing is generally static, and
is rigidly connected to the rest of the car through two pillars mounted at the
centre of the wing. Apparently, the safety factors employed in the dimensioning
of these pillars are not high, as it has been proven by a number of failures in
these components (see for example Alonso at Sepang 2013). As a matter of
fact, the high levels of downforce produced by the wing, as well as the internal
compliance of carbon bre, induce modications in the shape at high speeds:
the wing endplates tend to get closer to the ground, introducing a curvature in
the wing. Another eect that can be triggered is the vibration of the wing, as a
further consequence of the ow-structure interaction coupled with the anisotropic
stiness of carbon bre. It is therefore interesting to investigate the inuence
that these vibrations-oscillations can induce, from two standpoints mainly: one
is the gain in pure performance, the other is on the maximum forces that can be
generated, in order to prevent dramatic failures.
The topic of heaving and pitching wings has been widely investigated from the
point of view of applicability to Micro Aerial Vehicles (MAVs), small and light
devices that operate in Reynolds numbers in the order of magnitude of 10
2
10
3
:
2
1.2 Project Objectives
unsteady eects are exploited to produce thrust, without any other streamwise-
aligned power device to generate motion. The related increase in lift, with respect
to static conditions, is also a research subject. Many of the inspirations for the
design of these small devices come from biological yers, such as dragonies,
similar insects and small birds.
Very few studies have been realised merging these two topics, or with particular
focus on motorsport applications; moreover, CFD has always been the preferred
method to carry out these investigations. The combined inuence of unsteady
aerodynamics and ground eect on a generic race car front wing has not been
widely explored yet from an experimental point of view, especially in the range of
Reynolds number of 10
5
. This deciency has been the main driving force behind
the project.
1.2 Project Objectives
The principal target of this project is to improve the existing knowledge on the
behaviour of an inverted wing in close proximity to the ground while undergo-
ing oscillatory motion, with the employment of wind tunnel testing. The results
are to be referred to F1 cars and, more broadly, to motorsport applications.
This requires a careful assessment of the suitability and feasibility of wind tunnel
testing for such a case, with specic reference to Reynolds number and motion
frequency, and the technological bounds that are posed by state-of-the-art facil-
ities. The main goals can only be achieved if some intermediate objectives are
met, as listed below:
1. As the nature of this project is completely experimental, the required layout
has to be specied and, if necessary, designed and built. Since the wind
tunnel to be used was known from the start, the rst goal was to prepare an
experimental setup capable of providing the required data: this involves all
the aspects connected with experimental testing, such as physical models,
control software and data acquisition.
2. The second objective is strictly connected with the rst and indeed intrinsic
to the primary intent as well: understanding the current state of knowledge
3
1. INTRODUCTION
in the eld of unsteady aerodynamics, in particular for the cases of ground
eect and heaving motion. This entails the careful review of existing liter-
ature of the subject, in order to correctly steer the ensuing research.
3. Once the rst two objectives are completed, the actual testing can begin.
The acquisition of a coherent, consistent and accurate set of data is con-
sidered as an inevitable step and objective, and one not to be overlooked.
It is to be noted how an initial appraisal of wind tunnel capabilities is
of the foremost importance. This will entail the comparison of a simple
case to existing theories, to the positive outcome of which all the following
investigation is subordinated.
4. All the data acquired need to be analysed, taking into account what was
dened in the second step as of primary importance. Again, only a well-
documented and precise data processing can lead to meaningful results. The
objective here is therefore to prepare a programme capable of handling all
the data in a consistent and unique way, and to return signicant quantities
and results, as required by the specic objectives outlined in the previous
steps.
5. The nal and foremost objective is to draw conclusions based on the infor-
mations from the previous step, compare them with what was extracted in
step two and provide the reader with brief conclusions and suggestions to
steer further work.
1.3 Dissertation Layout
Where possible, this dissertation tries to follow a logical order in the rst place,
and a chronological one where not possible, in order to make it as understandable
as possible. This document is consequently structured as follows:
The second chapter is a survey of the relevant literature. A quick overview
of the inuence of aerodynamics on racing cars serves as the introduction to
the two main features that pertain to this study: inverted wings in ground
eect and wings undergoing one or two-degree-of freedom motion, mainly
4
1.3 Dissertation Layout
heaving. A review of the few articles dealing with these two congurations
in conjunction follows.
The third chapter involves an explanation of all the main facilities, models
and data processing techniques employed during the entire course of the
project. Relevant assumptions for the validity of the study and the testing
programme respectively open and close the chapter.
The fourth chapter is a comprehensive account of all the results obtained,
both for the preliminary investigation and the main one, including addi-
tional testing.
The fth chapter winds up the dissertation by presenting the conclusions
and suggestions for further work. It can be observed how the objectives
described in the previous section and the chapters contents are very similar,
which allows every part to be logically meaningful as a stand-alone section.
5
1. INTRODUCTION
6
2
Literature Review
This chapter presents an overview of the available literature that can be helpful
in building the fundamentals of the project. Given the inclination of this study
towards motorsport applications, a brief overview of the history and current role
of aerodynamics in racing cars is oered. The remainder of the chapter is more
pertinent to the actual physics of this study, and is divided into three sections:
the rst presents an introduction to the ground eect for inverted wings, and
eort was made in order to cover every and each of the signicant points of this
topic. The second section is an account of the recent progress made in the eld
of unsteady aerodynamics, when plunging and pitching wings are considered. In
contrast with the previous part, it was deemed as unreasonably time-consuming
and verbose to display all the research carried out with regards to the aforemen-
tioned problems, as a comprehensive review would encompass the entire eld of
unsteady aerodynamics. In attempt to be both exhaustive and concise, the fun-
damentals of the discipline are presented, which date back to the 1920s and 1930s.
Afterwards, the main research of the last 15-20 years is put forward, in order to
illustrate the most recent ndings; obviously this means that, time-wise, a gap is
present, but care was made to bridge it with small introductory paragraphs. The
third and nal section details the little existing research already carried out on
the combination of these two broader topics.
7
2. LITERATURE REVIEW
2.1 Aerodynamics of Racing Cars
The eld of aerodynamics can be considered relatively young, especially when
compared to the subjects of solid and uid mechanics in general. Aerodynamics
as a separate subject became relevant as aircraft technology advanced, and the
main ndings have been successfully applied to race cars in the last 50 years.
More recently, the particular conditions in which a race car nds itself, i.e. being
in contact with a surface that constrains the ow under the car, has justied
the existence of research specically focused on this topic. It is worth mention-
ing that, as a consequence of the increased attention and awareness towards the
environment, in the last years a number of studies have been carried out on pas-
senger cars as well, mainly aimed at reducing the drag at moderate speed, to cut
large-scale fuel consumption.
Taking a step back in time, at the very beginning of automotive history, aero-
dynamic eects were not considered to be an issue of any sort for cars, given,
basically, the very low speeds that were involved. As technology progressed, these
vehicles were able to attain higher speeds, with the rst car to actually break the
100 km/h barrier being the Jamais Contente, driven by Camille Jenatzy (11). In
these early days, the only aerodynamic-driven focus was to reduce the drag as
much as possible, which meant that cars were shaped as bullets or even styled as
raindrops, an example of this being the well-known A.L.F.A. 40-60 HP Castagna
Siluro Aerodinamica commissioned by Count Ricotti in 1914 (12). Perhaps the
rst man to understand the potential of aerodynamic loads perpendicular to the
ground produced by a car, Ettore Bugatti designed the 1923 Type 32 Tank de
Tours to be tted with an aerofoil-shaped bodywork, which produced lift. The
intuition was bright, the application was not. Many incidents, and even notable
fatalities, were triggered by aerodynamic eects, in particular when land speed
record were attempted and the speeds quickly rose up to 400 km/h and beyond,
the most famous case being the death of Auto Union driver Bernd Rosemeyer.
The main instance continued to be drag reduction, and even the studies by two
pioneers of automotive aerodynamics, Dr. Wunibald Kamm and Baron Reinhard
von Koenig-Fachsenfeld (13), were focused on this matter exclusively.
Despite an early, soon-to-be-forgotten attempt made by Opel, it was not until
8
2.1 Aerodynamics of Racing Cars
the 1960s that eective aerodynamic device were tted to a racing car, the rst
example being the number of features that appeared in a short time on the Cha-
parral 2 (14). Specically, the 2C is more often than not believed to have started
the legacy that still endures today, with the introduction of air dams at the front
and an adjustable, inverted wing at the rear end. This car, and its successors,
enjoyed such a number of victories that the idea of inverted wings was picked up
by Formula 1 teams in 1968, and by the end of this year all the cars on the grid
were equipped with these devices. In order to improve balance, a further wing
was added to the front end, close to the ground (15). The rst wings were im-
ported directly from aeronautical industry: this procedure proved to be initially
eective, but engineers soon realised that working condition on aeroplanes and
racing cars were very much diverse (16).
The second big aerodynamic revolution in F1 was represented by the increasing
comprehension of ground eect, with the rst car designed around this concept
being the Lotus 78, which was then perfected and raced as the iconic Lotus 79.
The introduction of skirts, that sealed the underbody creating perfect channels
under the car, made possible to reach massive amount of downforce and conse-
quently cornering speeds (17).
The inuence of aerodynamic devices on modern F1 cars performance is higher
than any other component, be it the engine, suspensions or electronics. The
downforce generated in high-speed bends can reach up to 3 or 4 times the weight
of the car, and the aerodynamic eciency is well above three, depending on track
characteristics; wings and diuser play a major role in the downforce genera-
tion process. It is interesting to point out that also the location of the centre of
pressure can highly aect the performance of the car, making the aerodynamic
balance another signicant parameter to monitor during the design process (18).
A number of researches have been carried out on particular components of racing
cars, in an attempt to utilise an academic approach to an industrial problem,
consequently focusing not only on the pure performance, but also on the funda-
mental physics and features governing the ow: besides several articles published
on front wings, studies have been published on diusers (19) (20) (21) (22) and
on wheels (23) (24), also with reference to their inuence on the front wing (25)
9
2. LITERATURE REVIEW
(26). It is anyway clear how the research into new concepts, and the continu-
ous, systematic betterment of the known ones, is pushed to the limit, and even
innitesimal improvements can make the dierence on track. It is consequently
clear how this dissertation places itself into this continuous strive for advance.
Figure 2.1: Chaparral 2C
2.2 Inverted Wings in Ground Eect
The purposes of a front wing are mainly three: increase the total downforce of
the car, bring the centre of pressure forward, and shape the ow in a benecial
way for the downstream components, such as diusers, sidepods and rear wing.
The front wing of a racing car produces a considerable portion of the total down-
force generated by the car, and in general can be assumed to be around 30% and
40% of this value (27) (28). The wing is placed very close to the ground, with
distances that are normally lower than 100 mm (29), and therefore smaller than
the chord of the wing itself. This means that the eect of the ground cannot
be neglected, and that the inuence of this wall on wing performance is of the
highest importance.
First mention of the modied pressure distribution of an inverted wing in prox-
imity of a wall is to be found in Zahm and Bear (30), who noticed how both lift
and drag substantially increased with respect to free-stream conditions. It was
not until the 1980s that systematic investigations of inverted wings in ground
eect began. A quantitative description of the modied pressure eld for a wing
10
2.2 Inverted Wings in Ground Eect
Figure 2.2: Modied pressure distribution for double-element wing in ground ef-
fect, from (18)
and ap conguration can be found in Dominy (31), who also stresses the impor-
tance of tip eects and consequently the necessity of endplates. The inuence of
the aspect ratio of the wing has been studied by Katz (32) (33), who showed a
remarkable inuence of nite-span eects, while the eects of wing geometrical
parameters, such as thickness and camber, has been explored by Coulliete and
Plotkin (34).
The rst comprehensive set of tests on a wing in ground eect was carried out
by Ranzenbach and Barlow: a number of experimental and computational simu-
lations was carried out, both on single-element wings (35) (36) (37) and double-
element wings (38). The inuence of ride height on wing performance was ex-
plored, at a constant angle of attack. The point of maximum downforce was
found to be at a non-dimensional ride height of 0.08, for a single element. The
reason for the subsequent downforce reduction was believed to be the merging
of aerofoil and ground boundary layers. It is to be noted how the wind tunnel
used in these tests employed a xed ground, meaning a thicker boundary layer is
formed. This could have aected the transferability of results to race conditions.
The rst introduction of a moving ground is linked to Knowles et al. (39), but the
results obtained are of little interest for real-case scenarios, as three-dimensional
eects are not discussed. It is worth mentioning that the incompressibility limit
11
2. LITERATURE REVIEW
Figure 2.3: Spanwise velocity vectors for wing in ground eect, from (41)
for ground eect is M = 0.15, as detailed by Doig et al. (40); shockwaves appear
from M = 0.4 onwards. These former results on the eect of compressibility
can help to explain the discrepancies that sometimes are observed between ex-
perimental and computational studies: at very low ground heights and Mach
numbers in the order of 0.1, an underprediction of force coecients is a char-
acteristics of incompressible solvers, that are often used in order to make the
computational cases quicker to solve. The most complete set of studies in this
eld was published as a result of the research completed by Zhang and Zerihan.
This study included a single-element wing (41) (42) and a double-element wing
(43) and (44). Subsequent overviews of the characteristics of the wake for these
two cases were performed by Mahon and Zhang (45) (46). The inuence of inow
conditions was investigated by Soso and Wilson (47) (48). Remarkable results
were obtained; only the ones regarding the particular geometry used in this study
will be reported.
For a single element wing, three clear regions, depending on ground clearance,
were pointed out: force enhancement, enhancement slowdown, force reduction
(41). The rst is related to the downforce growth experienced by the wing when
moving closer to the ground; at a certain distance, depending on other parame-
ters such as angle of attack and Reynolds number, the rate of downforce increase
is reduced. The enhancement slowdown region ranges from 0.15c to 0.3c, with
the latter value valid for a near-stall angle of attack. The maximum downforce
is obtained at ride heights between 0.1 and 0.15, with the gains in downforce
being more relevant at lower angles of attack. After this peak, the values for
downforce drop systematically: the reason for this is postulated to be the in-
12
2.2 Inverted Wings in Ground Eect
creasingly large adverse pressure gradient encountered by the ow on the suction
side, with regions of separated ow appearing at the trailing edge. Drag is found
to grow continuously when reducing ride height, and the rate of increase is ac-
tually larger in the force reduction region: it is therefore clear that this region
should be avoided, as the wing performance drops dramatically. From the point
of view of ow features and aerodynamic coecient, the presence of the ground
can be modelled to work analogously to an increased angle of attack for a wing
in freestream (49).
Two main features are believed to aect the force generation process: the Venturi-
like channel formed between the suction side and the ground, and the edge vortex
that is being formed beneath the two spanwise extremities of the wing. The rst
is responsible for the further acceleration experienced by the uid shortly down-
stream of the leading edge, as the region between the lowest point of the wing and
the trailing edge eectively forms a diuser, thus increasing the suction peak by
means of pressure pumping. Another signicant feature is represented, as said,
by the lower edge vortices, which eectiveness can be enhanced by the presence
of endplates. As a matter of fact, the pressure dierential across the two sides of
the endplate attracts uid from the external side, uid that rolls up and forms a
vortex beneath the wing itself, further reducing the pressure. The separation on
the suction surface is also delayed as a consequence of the increased mixing gener-
ated by this vortex. Induced drag is also raised by this ow feature. Overall, this
type of oweld is remarkably dierent from the almost two-dimensional one that
can be observed at centre span. As the ground height is further reduced, the vor-
tex moves inboard and grows in size (42). Vortex meandering is observed in the
enhancement slowdown region, and the vortex ultimately breaks down right after
the maximum downforce peak, triggering instantaneous and large-scale separa-
tion. The interaction existing between the lower and upper edge vortices created
by the endplate has been studied by Galoul and Barber (50): they showed how
the lower vortex has a strength remarkably higher than the upper one, which is
in turn bent downwards. At a certain point the two vortices merge.
Reynolds number eect on lift and drag was investigated by Jasinski and Selig
(51), who performed a comprehensive analysis including various type of wings
from Champ cars and F1 cars. They showed how an increase in this parameter
13
2. LITERATURE REVIEW
corresponds to a slight reduction in drag and a marginal increase in lift. De-
spite mentioning that, at low angles, the net positive changes in induced drag
are actually lower than the reductions in prole drag, they also proceed to state
that, when a ap is installed, front wing drag generation is dominated by in-
duced eects; no denitive conclusion seems to be reached. A reduction in peak
downforce has been found as the Reynolds number decreases (41), as well as an
increase in drag at all ride heights.
A further analysis on the Tyrrell 026 wing in ground eect was put forward by
Vogt and Barber (52), in particular on the pressure distribution on the wing: the
stagnation point was measured to move towards the ground as the wing is low-
ered. Consistently with previous research, an increase in suction on the pressure
side was shown; the pressure on the upper side is almost unchanged as the wing
approaches the ground, especially with respect to the suction side.
2.2.1 Gurney Flap
The Gurney ap is a small device generally tted to the trailing edge of the last
element of a wing, in order to increase maximum lift. It consist of a strip that is
mounted perpendicular to pressure side, with a size between 1% and 5% of the
wing chord. Documents showing a device of this type appeared across the 30s
and 40s (53) (54). It was Dan Gurney, an American driver, who rst introduced
this strip on racing cars in the 1960s, and it was then widely adopted by teams all
over the world, taking the name of the inventor. Despite its broad employment,
the reasons for improved performance are not yet a clear phenomenon.
One of the very rst investigations on the Gurney ap was carried out by Liebeck
(55), who performed wind tunnel testing, observed a decrease in drag and, at the
same time, an increase in lift. Reversed ow was also detected over the back sur-
face of the Gurney ap, as well as behind it. Two little counter-rotating vortices
are supposed to be the source of this latter ow reversal. The actual improve-
ments in performance are indicated to be a function of aerofoil thickness and
trailing edge shape, as already suggested by Duddy (54). Further research (56)
(57) showed that the Gurney ap has the same eect as increasing the camber of
the aerofoil, changing the angle of attack of zero lift, but not modifying the slope
14
2.2 Inverted Wings in Ground Eect
of the lift curve. Furthermore, the Kutta condition is not valid when the ap
is tted (58); its eectiveness is higher when its height is equal to the boundary
layer thickness at the trailing edge, on the pressure surface (59). The increase
in lift has been explained with the fact that the wake is turned downwards by
the presence of the ap. Additionally, a decrease in pressure on the suction side,
coupled with an increase on the pressure side, was detected.
A more recent research showed that the drag is slightly increased by the presence
of the Gurney ap, associated with a growth in maximum lift coecient. An
investigation into three-dimensional wings showed that an inboard placement is
more eective that an outboard one.
The rst study to include a time-history visualization of the ow structures of
a Gurney ap was carried out by Jerey et al. (60), opposed to the previous
ones, that focused solely on time-averaged data. Vortex shedding is observed to
take place, as a consequence of the interaction between the free-shear layers; the
separation point on the pressure side is xed, whereas it moves upstream on the
suction side as the angle of attack increases: this is believed to aect the size and
motion of the shed vortices, but indeed not their presence in the wake. More-
over, the nite distance existing between the two surfaces at the trailing edge is
designated as the cause for the increase in circulation, and ensuing increase in
lift. The increase in lift is also believed to be a direct consequence of the vortex
shedding, which enhance the suction peak on the lower surface. The maximum
improvement in lift coecient was measured to be +90% at null angle of attack,
and around +30% at stall angle, for a 4% Gurney ap. Drag increased as well,
but did not overshadow the gain obtained in lift, meaning that increased e-
ciency was measured. These improvements are not directly proportional to the
height of the Gurney ap, as a 0.5% GF shows already remarkable enhancement
with respect to the baseline; the rate of increase of lift reduces as the height is
raised. It is postulated that beyond a height of 0.05 times the chord, the benets
of further increasing Gurney ap dimensions would be negligible. The benecial
eect measured on single-element wings is generally replicated by double-element
wings (61), even thus the maximum increase in downforce is somewhat lower in
this latter case.
An examination on the eects of the aerofoil on the eectiveness of Gurney aps
15
2. LITERATURE REVIEW
Figure 2.4: Time-averaged momentum in the wake of a plunging aerofoil in
freestream, from (63)
has been carried out by Cole et al. (62): proles that feature a very early sepa-
ration on the suction surface show a lower rate of lift growth, or even a reduction
in lift coecient. This is in accordance to what observed before on the eect of
vortex shedding on the suction peak of the wing.
2.3 Unsteady Aerodynamics of Wings
The literature on heaving-pitching wings is vast and spans within a disparate
range of Reynolds numbers, shapes, applications and so on. Where possible, only
16
2.3 Unsteady Aerodynamics of Wings
the aspects relevant to this study have been investigated. Analytical expressions
for potential ow involving heaving and pitching motion for an aerofoil have been
developed by Theodorsen (64) and Garrick (65) respectively, and constitute the
basis for all subsequent studies.
The rst aspect related to a moving wing is the reduction in drag that can ul-
timately result in drag reversal and thrust production, a phenomenon that was
rst observed by Knoller (66) and Betz (67) independently. Karman and Burgess
(68) proceeded to postulate the dependence of this force on the the structure of
the wake, and in particular on the presence of alternate vortices behind the wing.
The existence of a vortex sheet downstream of a heaving wing has been therefore
studied and then decisively proven in a number of articles (69) (70) (71). The
presence of vortices in the wake is not only related to heaving motion but can
take place also for a stationary aerofoil because of a number of causes, all leading
to shear instabilities at the trailing edge (72). In the case of a Karman Vortex
Street (KVS), vortices that are shed in the wake are aligned in such a away to pro-
duce a momentum decit, thus generating drag. Heaving and pitching motions
have the potential to modify the relative distribution of these vortices, leading to
dierent wake structures. This changes can lead to a RKVS (Reverse Karman
Vortex Street), where the time-averaged momentum shows a jet-like momentum
gain, which denes thrust production. In particular, the vortex with positive
circulation is moved to the upper part of the wake, and the one with negative
circulation is moved to the lower part (73). Young and Lai (74) also noticed how
the VKS can actually be substituted by a wake containing multiple vortices per
cycle, thus denying the fact that the non-dimensional amplitude kh can be used
as the only parametre to assess the type of wake structure.
The dependence of the wake structure on the Strouhal number St was proposed
by Lai and Platzer (75); experimental tests performed using this similarity pa-
rameter for comparison yielded good accordance to the computational eorts of
Triantafyllou and Grosenbaugh (76). Both computational and experimental ap-
proaches have been tried to understand the complicate process of drag reversal.
It is to be noted how the VKS is an intrinsically unsteady process, with all the
vorticity concentrated in dierent points in the wake, thus making modelling a
very complicated matter (77).
17
2. LITERATURE REVIEW
Interestingly, the range of St capable of producing constant and well-behaved
thrust is exactly the one in which sh and biological yers operate, as detailed
by Drucker (78) and Wolgang et al.(79).
The actual parameters governing the drag-thrust transition have been widely
discussed, and still represent a partially open question. Godoy-Diana et al. (80)
studied the wake of a apping aerofoil by means of PIV, at Re in the order of 10
3
.
It was found that the type of the wake closely depends on two parameters, these
being the Strouhal number St and the amplitude A
D
of the motion itself. For
neutral and reverse wake to take place both the values should be above a certain
threshold, measured to be 0.1 for St
A
and 0.5 for A
D
. The regions containing
the same wake are delimited by curves similar to parabolae. This result justies
the introduction of a new parameter, the amplitude-based Strouhal number St
A
,
capable of containing both informations at the same time: the sole value of St
A
is enough to mark the lower boundary for thrust production. Another feature
indicated by PIV is the deection of the wake as the frequency and amplitude of
motion are further increased. The existence of a neutral type of wake, with per-
fectly aligned vortices and negligible drag has been conrmed by He et al. (81).
The deection of the wake at St > 0.5 has been observed by von Ellenrieder et al.
(63), who postulated that the onset of asymmetric wake depends on both reduced
frequency and non-dimensional heave velocity. Results were in accordance with
what already proposed by Lewin and Haj-Hariri (82). Wake deection seems to
dependent on the initial motion (whether upwards or downwards) and inuenced
by the ow features in the very rst moments of the heaving motion. They also
conrmed the results obtained previously by Liang et al. (83), who discovered a
positive correlation between deection angle and Re at xed St.
It is worthwhile to mention that the vast majority of these studies is computa-
tional, and has been carried out on two-dimensional models. Three dimensional
eects include the suppression of vortex shedding for very low aspect ratio wings.
Another eect triggered by a vertical motion of a wing is the dynamic stall,
which includes the dramatic increase in post-stall lift as the wing pitches and
plunges. This eected is believed to be triggered by the existence of a Leading
Edge Vortex (LEV), consisting of a small spanwise vortex close to leading edge
18
2.3 Unsteady Aerodynamics of Wings
on the suction side of the wing. A comprehensive discussion on this subject has
been presented by Shyy et al. (84). The dynamic stall mechanism has been
thoroughly explained by McCroskey and Fisher (85) (see gure 2.5): as the stall
angle is exceeded, ow reversal rst appears on the surface of the wing (b); as
the angle further increases, large eddies start to appear in the separated zone (c),
inducing an additional separation and ow reversal over the majority of the wing
surface (e). At this point the LEV appears, which role is to further reduce the
suction peak and consequently improve lift (f-g). The only mechanism capable
of breaking this cycle is the occurrence of moment stall (h), which induces a lift
stall as well. Deep stall ensues (j). When the angle of attack is reduced below
the stall angle, the full stall ends and the boundary layer reattaches (k), in order
for the entire process to happen again in the following cycle (l).
The presence of a LEV is highly critical to the total lift enhancement, and in
addition is a highly unstable mechanism, which is worth analysing in depth. The
size and position of LEVs changes with the time, as the wing undergoes its mo-
tion; lift enhancement is believed to be higher during downstroke and the nal
part of the upstroke, as detailed by Liu et al. (86). Actual gures were proposed
by Warrick et al. (87), who claimed that 75% of the total lift of the cycle is pro-
duced in the downstroke, whereas only the remaining 25% is due to the upward
motion. This is probably a consequence of the time frame in which the vortex
formation happens, namely at the beginning of the downstroke, as detailed by
Usherwood and Ellington (88). It is to be stressed how dierent models, based
on dierent types of yers, can yield very dierent results for what concerns axial
ow in the vortex, which inuences its stability, and other parameters such as
spanwise ow, as explained by Birch and Dickinson (89). It is anyway clear how
a requirement for actual lift increase is the attachment of the LEV for an amount
of time that is higher of at least half stroke. As an upper limit, vortex breakdown
seems to occur after 3 of 4 chords of travel. The mutual interaction between the
LEVs phenomenon and the propulsion eciency of a heaving wing is detailed in
Ashraf et al. (90): the LEV can be shed in the wake of the wing and thus modify
its thrust characteristics. It is observed how, at a xed kh, the thrust grows
with increasing reduced frequency. The dependence of drag and lift on reduced
frequency, on a NACA0012 aerofoil, was investigated by Medjroubi et al. (91): it
19
2. LITERATURE REVIEW
Figure 2.5: Dynamic stall mechanism for pitching aerofoil, from (85)
was found that both coecients bear a positive correlation with k. Interestingly,
altering the Reynolds number only does not result in any appreciable change in
these two coecients, whereas an incidence increment has high inuence on the
ow eld. The inuence of leading edge shape is investigated by Kang et al. (92):
it was shown that a sharp LE can lead to the formation of a stronger LEV, and
in general has an eect on the entire ow structure around and downstream of
the aerofoil. Furthermore, the dierences in ow characteristics between a at
plate and a cambered aerofoil is studied: the sensitiveness to Reynolds number
is higher for the aerofoil; remarkably, the at plate shows a higher maximum lift
coecient; phase shift is similar.
Another mechanism capable of signicantly increase lift is the rapid pitch-up, i.e.
the rapid rotation experienced by the wing at the two extrema of the motion.
The rst peak force, the one experienced during the upstroke-downstroke transi-
tion, introduces a component of rotational circulation that adds up to the already
existing value (93), thus increasing lift. The second peak force, happening at the
end of the downstroke, is part of a more complex phenomenon called wake cap-
20
2.3 Unsteady Aerodynamics of Wings
ture. All the eects due to the interaction between the wing and the wake fall
under the wake capture nomenclature: in particular, the features that inuence
ow characteristics on the suction surface are hereby discussed. The increase
in lift during this inversion is considered to be a consequence of the increased
velocity on the suction side (94); some doubts still exist on the real nature of
this force peak, as detailed in Sunada and Ellington (95), who postulate that this
improvement is only a consequence of the added mass eect.
The relative magnitude and inuence of various ow phenomena, at dierent St,
has been studied by Andro et Jacquin (96): when the Strouhal number is lower
than 0.1, the only signicant lift enhancement mechanism is represented by the
presence of the leading edge vortex, which accounts for a quasi steady circulatory
force. As St in increased, both added mass and wake capture start to play a
relevant role too. As St is beyond 0.5, the acceleration grows accordingly, thus
increasing the importance of the added mass eect, which becomes the only sig-
nicant source of lift enhancement. Moreover, the wake capture seems to work
best at St = 0.4, and as this value is surpassed, the vortices being shed decrease
in size, thus reducing the mean lift.
Another important factor in the process of leading edge vortices shedding is the
thickness of the wing, which strongly aects both the formation and the shedding
timing. As explained by Yu et al. (97), aerofoil below a certain thickness do not
shed the LEV in the wake; instead, the LEVs remain close to the leading edge
for the entire cycle. This introduces an aperiodic component in the aerodynamic
loads, and in particular in the thrust production.
2.3.1 Theodorsens Theory
In 1935, Theodore Theodorsen performed a comprehensive theoretical analysis
of the unsteady aerodynamics of an aerofoil and aerofoil-aileron (sic), using non-
stationary potential ow theory and applying the Kutta condition at the trailing
edge. A theory based on innitely small oscillations was developed, which should
not be aected by the aerofoil characteristics such as thickness and camber. Three
forces were considered, as explained by Theodorsen himself: the inertia forces,
the restraining forces and the air forces. A rigorous mathematical tractation of
21
2. LITERATURE REVIEW
Theodorsen theory will not be put forward here, as the referenced paper already
contains it, and it is widely available. Only the relevant steps will be presented.
For the non-circulatory part, six potential velocities are introduced to completely
model the ow around the aerofoil: these velocities are computed from a number
of sources placed around the geometry. Once the velocity potentials are known,
it is possible to compute pressures and therefore, by integration, obtain the forces
and moments acting on the aerofoil. The circulatory ow is solved through the
introduction as a vortex element moving with respect to the aerofoil; Kutta con-
dition is used to determine the total circulation. Vertical forces and moments are
then derived.
The Theodorsen function C is introduced as the ratio of the integrals introduced
in the circulatory component computation. Furthermore C is dened as being a
function of the reduced frequency only, hence
C = C(k)
The Theodorsen function is further divided into two terms such as
C(k) = F(k) + iG(k)
The function can also be expressed as the ratio of Hankel functions, which in
turn are complex combinations of Bessels functions. The role of the Theodorsen
function is to return the lift variation, with respect to static conditions, as a
function of the reduced frequency only. Moreover, it is possible to derive the
phase shift with respect to the oscillation. The total lift, for a heaving and
pitching wing, can be written as
C
L
=
_
h + a
_
+ 2
_
+
h +
_
1
2
a
__
C(k) (2.1)
as detailed by Brunton and Rowley (98). The rst term accounts for the added-
mass eect, whereas the second is an expression of the quasi-steady lift compo-
nent. The term a represents the position of the pitch axis. For the case of pure
heaving, the total lift can be written as
L =
1
4
c
2
y +U
2
cC(k) y
22
2.3 Unsteady Aerodynamics of Wings
It is also possible to express this quantity as a function of a complex variable
(99), such that
L = 2U
2
k
2
2
Gk +iFk
_
ae
i2ft
= 2U
2
k
2
2
Gk + iFk
_
y
and the phase shift between the position and the lift waves represented as
= atan
_
F(k)
k
2
+G(k)
_
For the sake of consistence with previous research, the phase shift will not be
referred as an angle, but as a pure number
h, such that
h = cos()
Another study was carried out by Garrick (65) in order to assess the energy
required by the system to produce and maintain thrust. The conditions, and
assumptions, under which this work holds are the same as Theodorsens, and the
methods employed are very similar. The proposed formula is
W =
E +
P
x
v (2.2)
The quantity
W represents the average power required to maintain oscillations;
E
is the increase in energy, per unit time, in the wake. The third term is the propul-
sive power. After a number of mathematical manipulations, the ratio between
the propulsion energy and the total energy given to the system from outside the
system is shown to be
P
x
v
W
=
F
2
+G
2
F
(2.3)
2.3.2 Aeroelasticity
One important feature to be taken into consideration, when dealing with unsteady
aerodynamics, is the concept of utter, dened as amplitude of oscillation in-
crease caused by negative damping (100). A one degree of freedom motion, such
as heaving, should not be subjected to this phenomenon, unless separation takes
place (101) (102). As separation is not predicted to be a factor to this study,
23
2. LITERATURE REVIEW
given the expected ride heights and angles of attack, utter can be considered
not to be an issue. Conversely, static aeroelasticity has to be taken into account.
An aeroelastic analysis of the structure employed in this study will developed
from the examples presented by Hodges and Pierce (103).
The model can be considered to be a cantilever beam hinged to the top of the
wind tunnel, with the beam perpendicular to the ow. For a static condition, the
focus is on the deection angle induced by the compliance of the structure, which
adds up to geometric angle of attack, and can induce failure of the structure,
if the moment induced by pitching becomes uncontrolled. The total deection
angle is
=
F
+
M
with
F
=
F
0
(2y)
2
2EI
;
M
=
M
0
(2y)
EI
with F
0
and M
0
being the horizontal force and the moment due to the strut
internal stiness, if 2y is the total length of the strut. A further vertical force
introduced by the strut can be called R
0
. Horizontal balance gives only
D F
0
= 0 (2.4)
where D is the drag. Vertical balance yields
L +R
0
+W = 0
with L being the lift, pointing upwards, and W being the weight. It is to be
noted how this equation does not contain any term including the deection angle.
Momentum balance gives:
M
0
2Wysin M
ac
= 0 (2.5)
with being the angle between the strut vertical and the line passing through
the hinge and the centre of mass. M
ac
is the moment due to aerodynamic forces.
Drag and moment appear in the previous equations. It is decided, given the low
overall incidence and the presence of ground eect, to assume the rst as linear,
24
2.3 Unsteady Aerodynamics of Wings
and in case apply a a safety factor, if necessary, later in the process. Drag is
expressed as
D = qSC
D
eff
where q is the freestream dynamic pressure. Since the calculations are carried
out at the aerodynamic centre, the momentum contribution from the aerofoil is
independent from angle of attack, leading to
M
ac
= qScC
M
ac
Substituting the denition of deection angle and solving 2.4, it is possible to
obtain
F
= qSC
D
( +
M
)
_
4y
2
2EI 4y
2
qSC
D
_
The moment balance gives the solution for the second deection angle
M
= (2Wysin qScC
M
ac
)
2y
EI
Summing the two terms results in the elastic part of the increase in incidence ,
as
= qSC
D
_
EI
2y
+ 2Wysin qScC
M
ac
_ _
8y
3
EI 2EI 4y
2
qSC
D
)
_
+
2y
EI
(2Wysin qScC
M
ac
)
It is now sucient to study the denominator of this equation to nd when the
eective angle of attack is expected to blow up, i.e. when
(EI)
2
_
2EI 4y
2
qSC
D
_
Since the dependent variable here is velocity, which is comprised into the dynamic
pressure term, it is possible to dene the divergence pressure q
d
as the minimum
pressure that leads to the uncontrolled increase in eective angle of attack, as
q
d
=
2EI
4y
2
qSC
D
(2.6)
For this structural conguration, there is not a course of action capable of making
the negative pressure negative, as it is sometimes the case. As expected, in order
to increase this pressure, and the divergence velocity accordingly, the overall
stiness has to be increased, or the vertical distance decreased.
25
2. LITERATURE REVIEW
2.4 Combined Eect of Oscillations and Ground
Presence
The studies presented in the previous subsection cannot be fully applied to the
conditions of this study, since they lack in two fundamental features: ground
presence and Reynolds number. This last quantity is generally limited to 10
4
in
the best case, as a result of experimental constraints and researchers interest.
As proven by Isaac (104), the extrapolation of high Re results from low Re ows
would be completely inaccurate, as a consequence of the particular ow features
involved.
Indeed, the topic of an inverted wing in ground eect undergoing an oscillatory
motion has enjoyed little popularity: just a few articles exist. Some interest has
been displayed in the phenomenon of hysteresis, under which name fall all the
eects connected with the dierences observed at a certain ground clearance de-
pending on the direction of approach, i.e. whether moving upwards or downwards.
It is to be remarked how this behaviour is dierent from an harmonic, oscillatory
motion, from both the standpoints of ow physics and aerodynamic loads. An
early study was carried out by Moryossef and Levi (105), using a one-equation
turbulence model coupled with a Euler/Navier-Stokes ow solver. It was found
that the average downforce was very close to the static value at the same ground
clearance, whereas the amplitudes of oscillation for both lift and drag increase as
the reduced frequency grows. Only the rst mode is found to be important for
lift, whereas, for drag, higher modes (generally second and third) are of the same
order of magnitude of the rst, and can not be neglected.
Two comprehensive articles have been published by Molina and Zhang (99) and
Molina et al. (106), investigating both the magnitude of lift and drag coe-
cients, and their behaviour in time with respect to the oscillatory motion. From
the point of view of lift, the proximity to the ground seems to yield more increase
in downforce at higher frequencies than at lower ones; furthermore, it is estab-
lished that if k < 1.09 the frequency variations do not have any tangible eect.
Thrust in freestream is said to be generated at k = 2.31, a value that rapidly
increases as the wing is brought close to the ground: at h/c = 0.33, the boundary
between drag and thrust is beyond k = 4. Peak forces are shown to increase as
26
2.4 Combined Eect of Oscillations and Ground Presence
reduced frequency increases and ground eect decreases. Peak to peak amplitude
increases as well, and for some conditions (provided k > 2) positive lift can be
produced in some parts of the cycle. Instantaneous switch from lift to drag can
take place at reduced frequencies as low as 0.34, with this value strongly depend-
ing upon the ride height.
Another parameter to be taken into account is the phase shift between motion
and downforce waves. This is inuenced both by the initial position of the aero-
foil (its mean ground height) and the reduced frequency. Three main eects can
be isolated: ground presence, increased angle of attack and added mass; the last
two are already present in Theodorsens theory and account for the circulatory
and non-circulatory elements respectively.
At very low reduced frequencies, the ow can be considered quasi-stationary, and
the downforce generated at each position depends only on this quantity, as no
dynamic eects play a role; the boundary between quasi-stationary and unsteady
regions is set at k = 0.11. In this range of frequencies the ground presence is
therefore the only element that aects performance. As the reduced frequency is
increased, the velocity at the central point of the motion starts to be signicant,
introducing an eective angle of attack, dened as
eff
=
0
+ atan
_
dh
dt
U
_
(2.7)
The role of this increased angle of attack is to increase the lift of the wing, thus
moving the point of maximum downforce towards the centre of the motion, with
a null phase shift. The magnitude of maximum phase shift depends on both
reduced frequency and ride height: as the wing is moved closer to the ground, its
presence is more inuential, therefore bringing the two waves closer and increasing
the reduced frequency at which this is reached. The limiting case is when the
motion occurs for the most part in the force reduction region, and the eect of
increased incidence induces a dierent shape in the
h vs. k plot, as detailed in
gure 2.6. Since the presence of the
0
term in the previous equation, it is clear
that the geometrical characteristics of the wing, and its initial angle of attack,
can inuence the eectiveness of the increased angle of attack phenomenon. As a
matter of fact, an
0
close to stall angle could trigger a separation-reattachment
27
2. LITERATURE REVIEW
Figure 2.6: Phase shift as a function of reduced frequencies at dierent ride
heights, from (99)
cycle dierent from free-stream, as the ground would both worsen the eect of
separation and reduce the eectiveness of the diuser. As the reduced frequency
is further increased, an inviscid eect starts to move the phase shift back to 0,
and therefore the point of maximum downforce back to the lowest position of the
oscillatory motion, this time regardless of the initial ground height. The added
mass eect is related with the amount of uid that has to be displaced by the wing
during its movement; the force generated by this phenomenon is proportional to
the acceleration of the wing, with the following law:
F
mass
=
d
2
h
dt
2
(2.8)
Depending on the frequency, at the beginning of the upstroke a positive lift can
be experienced by the wing; in racing conditions, this would mean that the car
is highly unstable and almost impossible to drive. It is to be noted how this
phenomenon has the same eect on all the ride heights, meaning that all the
curves in Molina merge at a reduced frequency higher than 1.01.
28
3
Research Description
This chapter presents a description of the methods used in this research, including
the overall methodology, the relevant assumptions, an account of the model and
software used, as well as the initial programme for the wind tunnel testing. This
chapter is conceived as a series of information that can help understanding the
following one, and as a reference in case similar experiments are to be repeated.
3.1 General Approach
It has already been mentioned how, to the best knowledge of the author, this is
one the rst experimental studies of a heaving wing in ground eect at a Reynolds
number in the order of 10
5
. A careful planication is therefore highly necessary,
as well as a clear denition of the objectives.
As customary with experimental testing, the rst variable to consider was the
availability, and in second order the specications, of a wind tunnel. The RJ
Mitchell wind tunnel at the University of Southampton features is commonly
used for motorsport, aeronautical and sport-related research, making this the
preferred choice. The dimensions and principal characteristics of this facility are
described later in this same chapter. Once this is settled, the actual model to
be employed has to be decided. Contemporary F1 front wings are extremely
rened, and feature an incredible numbers of aps, appendages and other micro-
aerodynamic devices. Beside the obvious manufacturing complication of building
such a model, two main problems exist: the rst is to actually get a blueprint for
29
3. RESEARCH DESCRIPTION
such a component, and the second is to eventually discern the main factors that
inuence performance. As a consequence, a simple single-element wing model
was used, for which static experimental validation (for the stationary case) and
computational validation for dynamic cases, is available in literature. The rela-
tive simplicity of this model makes possible to eliminate non-fundamental ow
features and force behaviours, and to concentrate only on the desired variables.
The validation data available constitute the baseline cases as well, to which the
following results are to be compared, when possible. The selection of the model
allows to design all the relevant components that need to transmit the alternate
motion to the motor to the wing, transforming it into a linear, vertical, displace-
ment. The role of this structure is also to ensure the required rigidity and stiness
at design conditions.
The last part of this preliminary analysis is to determine what are the quanti-
ties to be analysed. As ow visualization techniques are not available, the focus
is shifted on the investigation of drag and lift principally, and their dynamic
behaviour. The independent variables to be changed are four: ground height,
wind speed, motion amplitude and motion frequency; these, in turn, dene other
non-dimensional parameters such as reduced frequency, Reynolds number and
Strouhal number. The actual test programme is presented in the next subsec-
tion.
3.2 Test Programme
The test programme was prepared bearing in mind that one of the principal ob-
jectives was to reach a reduced frequency as high as possible, which can be done
by varying two quantities: wind speed and motion frequency. In particular, an
increase in frequency and a decrease in speed will obtain the same net change.
Both the quantities are indeed limited by practical constraints: the motor needs
a nite amount of time to invert its motion, and the wind tunnel speed is only
constant throughout the entire cross-section at a determinate value. This latter
was placed at 5 m/s, which was is considered to be the lower operational limit of
the wind tunnel, where the maximum frequency that was possible to obtain from
the motor (with an amplitude of 10 mm) was of 5 Hz. These two restrictions,
30
3.2 Test Programme
along with the chord of the wing, limited the maximum attainable reduced fre-
quency to 0.73.
Another objective was to examine the inuence of dierent parameters on lift and
drag: namely, the ride height, the Reynolds number (governed by the wind speed
only) and the motion frequency. It was therefore decided that a comprehensive
set of test was needed. The wind tunnel velocities spanned between 5 and 40 m/s,
with steps of 5 m/s, the ride heights went from the lowest allowed by geometric
constraints (0.45) to one almost in free-stream (1.35), with three intermediate
values to bridge the gap (0.60, 0.75 and 0.90). Once this grid had been created,
all the dierent speed/clearance congurations were explored at various motion
frequencies, from 1 to 5 Hz, with 1 Hz steps, thus creating a three-dimensional
matrix.
Additional tests were performed with a 2.2% Gurney ap tted to the trailing
edge of the wing and a rough strip on the suction side, as already listed in the
relevant section. Only two motion frequencies (3 and 5 Hz) beside the static con-
guration, were investigated. Moreover, at a xed frequency of 3 Hz, the eect of
dierent amplitudes, and therefore dierent Strouhal numbers, was studied. The
angle of attack of the wing was kept constant at 0.5
. The ride
height was initially measured using a ruler, perpendicular to the ground,
with a resolution of 1 mm. Only the minimum ride height was measured,
and then all the other ground clearances were obtained by displacing the
wing, using the electric motor, by a known quantity. The resolution of the
motor is much better than the ruler, and will not me discussed, since the
inaccuracies due to it would be negligible. Since all the quantities were
measured through the overhead balance, the accuracy of this component
has to be taken into account as well. It is anyway postulated that this
represents only a small part of the total errors.
3.4 Experimental Setup
3.4.1 Wing Assembly
The tests wee performed on an untwisted, untapered single element rectangular
wing. The wing prole is derived from the main element of the front wing used in
the 1998 Tyrrel 026 Formula 1 car. This aerofoil was developed starting from a
NASA GA(W)-1 prole, type LS(1)-0413, in order to reduce the magnitude of the
wake, by changing the position of the suction point, which was moved upstream
(41). A nite trailing edge has been introduced as well. The wing used was the
test is an 80% model, with a chord of 233 mm and a span of 1100 mm, with a
corresponding aspect ratio close to 5. The model is hollow and made of carbon
bre. This wing was used for testing in ground eect a number of times already,
and validation data is widely available. Specically, since its rst appearance
this prole has quickly become the reference for the niche of inverted wings for
motorsport applications, and the vast majority of research on this topic has been
carried out on it.
A 2.2% Gurney ap was added after the rst round of wind tunnel runs; it
consisted of an L-shaped aluminium strip that was glued, on one side, to the
wing. An adhesive stripe covered with grit was subsequently added to induce
transition on the suction side, this being centred at 10% of the chord, and with
a width of 4% of the chord approximately. Two aluminium-made, 2-mm thick
34
3.4 Experimental Setup
Figure 3.1: CAD rendering of entire wing assembly
35
3. RESEARCH DESCRIPTION
endplates were tted at each end of the wing, with a length of 250 mm and a
height of 100 mm; the lower edge of the endplate was placed at 1 mm from the
lowest point of the suction side.
The existing parts were reverse-engineered and translated into a CAD le, from
which the mountings were developed: the connection between the horizontal
struts and the wing was designed to be performed using two aluminium plates,
bolted to the wing using two existing cavities on the pressure surface, at a distance
of 32% of the span from the centre point. These were connected through two
streamlined struts to a carbon bre sting, which aim was to transmit the motion
from the motor to the wing. The cavities on the wing were covered with tape
during testing, to prevent any unwanted interaction with the incoming ow.
3.4.2 Wind Tunnel
Figure 3.2: Wing in the wind tunnel
All the tests were performed in the RJ Mitchell Wind Tunnel at the University
of Southampton, which has been already employed for industrial, motorsport
(Formula 1 and Indycar) and academic research. This wind tunnel features a
return circuit design and a closed test section, with cross-sectional dimensions of
36
3.4 Experimental Setup
3.6 x 2.5 m (11 x 8). The test section is approximately 10.5 m long. On the
four corners of the testing section side llets, with an angle of 45
, are present.
The speed range of the wind tunnel is between 5 and 40 m/s, and the maximum
turbulence intensity, dened as
Tu =
u
2
U
eff
=
0
+ atan
_
dh
dt
U
_
(4.1)
For an harmonic sinusoidal oscillation, velocity can be expressed as
dh
dt
= x(t) = afcos(ft) (4.2)
From 4.1 and 4.2
eff
=
0
+ atan
_
afcos(ft)
U
_
which entails that the eective angle of attack is maximum for cos(t) = 1
(central point of oscillations) and equal to the geometrical one for cos(t) =
0 (extrema of oscillation). It is possible to plug in the denition of reduced
frequency k =
fc
U
to obtain
eff
=
0
+ atan
_
akcos(ft)
c
_
(4.3)
thus introducing a direct dependence on reduced frequency, at least for a sinu-
soidal motion; it is possible to reproduce this derivation every time the motion
54
4.2 Clean Wing
Figure 4.12: Phase shift vs. reduced frequency, h/c=0.45
can be dened as a continuous function. It is also to notice how the introduction
of a new variable, namely
h =
a
c
could non-dimensionalise the motion amplitude with respect to the chord, in order
to obtain a further similarity parameter. The behaviour in 4.13 can be explained
from 4.3, as the phase shift is dependent on reduced frequency, at least in the
range of k were the increased angle of attack is expected to play a signicant role.
Moreover, an increment in the maximum amplitude shows an analogous response;
both are non-linear eects since the presence of the trigonometric function.
The eective angle of attack at a given position can be derived by knowing the
quantity
k
hkU
sin(ft)
It is clear that the added mass eect cannot be derived from non-dimensional
parameters only, but that some other quantities need to be known as well.
4.3 Gurney Flap
As additional tests, it was decided to t the wing with a Gurney ap placed on
the trailing edge. The dimension of the ap was approximately 2.2% of the chord,
56
4.3 Gurney Flap
Figure 4.14: Lift and drag coecients vs. wind speed, GF and TFX
well in the range of what is commonly used on racing cars. Afterwards, a strip
with ne grit was placed at 0.1c (consistently with (41)) on the suction side of
the wing, in order to trip the boundary layer and force the formation of boundary
layer through roughness and consequent by-pass transition.
As with the clean wing, the rst runs were aimed at assessing the consistency with
existing data. As it can be observed in gure 4.14, the lift coecient is increased
by a considerable factor with respect to the clean wing, while the transition-xing
condition has a negative eect on both lift and drag. Still, the lift values for this
last case overshoot what was observed for the clean wing with free transition.
Drag increases as well. It is noteworthy to point out how the drag is almost
constant when the transition is xed, which entails that the skin friction is critical
for this case. Drag for the transition-free case grows with Reynolds number,
similarly to the clean wing.
For this particular setup, a new, non-dimensional parameter was introduced,
called oscillation factor, dened as
OF =
F
F
1
which is the ratio between the standard deviation and the mean of the desired
quantity (in this case, lift or drag). From a practical point of view, it is useful
to know how much the lift and drag values vary, especially when compared to
57
4. RESULTS AND DISCUSSION
Figure 4.15: Non-dimensional oscillation factor, lift and drag, GF and TFX
the mean quantity. It can be seen how an increment in reduced frequency highly
increases the oscillation amplitude, as it is expected, since the ow is experiencing
more unsteadiness, a quantity for which the reduced frequency is an accurate
indicator. In particular, oscillations in lift are higher when the transition is xed,
whereas the opposite situation is observed for drag. This latter behaviour can
be explained by the fact that a higher component of the drag is skin friction
(since transition is forced), which remains almost constant throughout the entire
oscillating regime, reducing the non-dimensional factor. The higher variability in
lift can be explained by a thicker boundary layer, more prone to separation at
higher eective angles of attack, which induces a more pronounced separation-
reattachment mechanism.
As a further investigation, lift and drag obtained at dynamic conditions were
compared with the static value. The lift displays an interesting behaviour: the
dynamic cases show a remarkable improvement, at least at reduced frequencies
higher than a threshold, that appears to be around 0.4. A peak in this quantity is
observed around 0.5 for the highest Reynolds number, whereas a steady growth
is seen at Re = 79000, but with a decreasing rate as the reduced frequency is
increased. Drag shows the opposite behaviour: for k > 0.4, the drag starts to
constantly decrease for all Reynolds number, reducing to around 80% of the initial
value. It is interesting to notice how this type of behaviour is something that is
58
4.3 Gurney Flap
Figure 4.16: Non-dimensional lift and drag vs. reduced frequency, GF and TFX
encountered at higher reduced frequencies for a clean wing, which would suggest
that the addition of a Gurney ap can be considered, in some sense, similar to
an increase in reduced frequency. It is to be remembered that the wake of a
wing equipped with a Gurney ap features a discrete vortex shedding in static
conditions already. The reduction in drag can be explained with the dierent
alignment of shed vortices when an oscillatory motion is applied, a situation that
does not take place with the clean wing at reduced frequencies below 1. The
role of the Gurney ap in this drag reduction is therefore indirect, as it is simply
needed to trigger the vortex shedding in the wake. It is indeed more complicated
to explain the increase in lift; it can be postulated that the pressure dierence
at the trailing edge is increased by the oscillatory motion, thus inducing a higher
base suction.
Figure 4.17 shows the phase shift for all the three main cases considered, at a
constant ride height h/c = 0.45 . It is observed that the peak is both anticipated
and increased, as the increased angle of attack plays a more prominent role at
a lower reduced frequency: the presence of Gurney ap induces a higher lift as
the eective incidence grows. The slope is also steeper, for the same reason.
The presence of transition xing can introduce separation at the trailing edge,
introducing new ow features in this zone, especially if the presence of the Gurney
ap is considered. As a consequence, at low reduced frequencies the behaviour
59
4. RESULTS AND DISCUSSION
is very similar, since the increase in angle of attack is low, as shown in 4.17.
Afterwards, the dierence is more noticeable. The two curves the remain at an
almost constant distance. Furthermore, the three curves seem to tend back to
h = 1 with dierent slopes, lower for the Gurney ap-equipped wings, higher
for the clean wing. This is again a consequence of the more powerful inuence of
the eective angle of attack, triggered by the presence of the Gurney ap at the
trailing edge.
Figure 4.17: Phase shift vs. reduced frequency for dierent cases
60
5
Conclusions and Further Work
The present study falls in the line of a research sector aimed at shedding light on
the possible improvements attainable by introducing unsteady ow features, by
means of externally-actuated motion on a lifting surface, such as a wing. Speci-
cally, the focus of the project was to assess the suitability of wind tunnel testing to
the case of a planar, rectangular wing in heaving motion, at Reynolds numbers in
the order of 10
5
. Subsequently, to investigate the inuence of ground presence on
the aerodynamic loads produced by the wing itself, at dierent Reynolds number,
frequencies and wind speeds, with particular reference to the available literature.
A model capable of carrying the predicted loads has been designed and built, as
shown in Chapter 3. The preliminary tests, aimed at appraising the suitability of
the available facilities, have been undertaken as a necessary step towards the com-
pletion of the project. In particular, lift measurements for a wing in freestream
conditions were compared with what is predicted by the Theodorsen theory, in
order to validate the procedure that has been followed in the following tests.
Good agreement was found between the two sets of data, at least for the range of
reduced frequency that were permitted by the intrinsic limits posed by the avail-
able facilities, wind tunnel and electric motor in primis. It is worth mentioning
that one of the main constraints of wind tunnel testing for similar cases is the
upper boundary of reduced frequency, which is limited by the maximum motion
frequency that can be transmitted to the wing, and the minimum wind tunnel
speed at which a steady ow is obtained. These two technological bounds are
61
5. CONCLUSIONS AND FURTHER WORK
remarkably dicult to overcome, especially if the importance of Reynolds num-
ber is considered: an hypothetically smaller, and therefore lighter, model would
allow for higher frequencies to be reached; however, this would mean lowering the
Reynolds number. As a matter of fact, the trade-o between these two quantities
is something to be carefully considered when preparing a test programme, or even
dening project objectives.
An important step of the project was to assess the suitability of the selected wind
tunnel for this type of research, by comparing the theoretical values predicted by
Theodorsens theory with the experimental results. Once this was done, it was
possible to move the wing closer to the ground, in order to investigate ground
inuence. The relative inuence of three quantities on lift and drag coecients
was studied: Reynolds number, ride height and reduced frequency. It was found
that all variables can play a signicant role, and their combined inuence was
assessed as well. The magnitude of force uctuations is found to be qualitatively
similar to what was observed with CFD; the phase shift showed good agreement
as well. The dependence of the eective angle of attack on the Strouhal number
was demonstrated. Additional tests were performed on the same wing, adding a
Gurney ap at rst, and then placing a rough strip on the suction side to trip
the boundary layer. The maximum phase shift (expressed as
h) was observed to
increase, while the reduced frequency at which it occurs decreased. A benecial
eect of increasing the reduced frequency was discovered on both lift and drag, as
a consequence of the vortex shedding introduced by Gurney ap presence even at
k < 1. The maximum oscillation in lift and drag was observed to be dependent
on reduced frequency too, as predicted.
Overall, the project proved the possibility of performing tests on non-stationary
wings at Re in the order of 10
5
, and M in the order of 0.1. The calibration proce-
dure, to obtain the inertial forces, was validated against theoretical results. The
eectiveness of oscillatory motion to reduce drag is negligible, at least for k < 1,
as from existing literature. Conversely, it was rst shown that the presence of a
Gurney ap, which induces signicant vortex shedding even at very low frequen-
cies, can help to reduce drag and improve downforce, as the vortices respective
positions are modied by the wing motion, with respect to the static condi-
tions. The distribution of vorticity could lead to thrust characteristics at a much
62
lower value of reduced frequency than a clean wing. The contribution towards
downforce generation of the increased angle of attack eect grows in magnitude.
Similar trends, quantitatively less marked, are observed when the boundary layer
is tripped on the suction surface. In particular, a lower sensitivity to the eective
angle of attack and Reynolds number can be detected. Finally, from the results
of this investigation, improvements in aerodynamic eciency and performance
in racing conditions are deemed as denitely possible; the study performed on
Gurney ap presence are particularly encouraging from this standpoint.
This research showed very promising result, especially for what concerns the
employment of experimental-based procedures for unsteady analysis, at a scale
signicantly bigger than what is commonly employed. One of the limits, as men-
tioned, is the relatively low reduced frequency that can be achieved. To increase
this, the simplest method would be to have a higher motion frequency, which
could be attained with either a dierent motor or a lighter model. Covering up
to k = 3 would mean increasing the motion frequency to 15 Hz, at xed chord
and wind speed. Another extension would be to build a model that could inves-
tigate lower ride heights, and eventually go as low as the force reduction zone.
Furthermore, a more comprehensive analysis of the inuence of motion ampli-
tude would help to shed more light on the phenomenon. Eventually, the eect of
non-sinusoidal and even random oscillations is to be taken into consideration.
This project, for the most part, considered the eect of oscillatory motion and
ground presence from the standpoint of two quantities, lift and drag. Employing
visualisation techniques to explore the ow features in the wake of the wing is
of primary importance, given the importance of vortex shedding for this partic-
ular case. Pressure measurements on the two wing surfaces would arguably be
helpful as well. From the point of view of actual results, further studies on the
contemporaneous eect of Gurney ap and oscillatory motion is surely required,
as it was observed to be very promising and carrying a lot of potential, as it could
result in a much improved aerodynamic eciency with a very little mechanical
input from the outside. Further research would, ideally, include double-element
wings, or even more complex layouts, in order to approach actual F1 wings.
63
5. CONCLUSIONS AND FURTHER WORK
64
References
[1] Fish F.E. and Hui C.A. Dolphin swimming - a Rev.
Mammal Rev., 21(4):181195, Dec 1991. 1
[2] Carpenter P.W. Davies C. and Lucey A.D. Hydrody-
namics and compliant walls: Does the dolphin
have a secret? Current Sc., 79(6), Sep 200. 1
[3] Pavlov V.V. Dolphin skin as a natural anisotropic
compliant wall. Bionspiration and Biomimetics,
1(2):3140, Jun 2006. 1
[4] Bechert D.W. and Bartenwerfer M. The viscous ow
on surfaces with longitudinal ribs. J. of Fluid
Mech., 206(1):105, Sep 1989. 1
[5] Bechert D.W., Bruse M., and Hage W. Exp. with
three-dimensional riblets as an idealized model
of shark skin. Exp. in Fluids, 28(5):403412, May
2000. 1
[6] Dean B. and Bhushan B. Shark-skin surfaces for
uid-drag reduction in turbulent ow: a Review.
Philos. Trans. of the Royal Soc. A: Math., Phys.l and
Eng. Sc., 368(1929):47754806, Sep 2010. 1
[7] Johari H., Henoch C.W., Custodio D., and Levshin A. Ef-
fects of Leading-Edge Protuberances on Airfoil
Performance. AIAA J., 45(11):26342642, Nov 2007.
1
[8] van Nierop E., Alben S., and Brenne M. How Bumps
on Whale Flippers Delay Stall: An Aerodynamic
Model. Phys. Rev. Letters, 100(5), Feb 2008. 1
[9] Fish F.E., Weber P.W., Murray M.M., and Howle L.E.
The Tubercles on Humpback Whales Flippers:
Application of Bio-Inspired Tech. Integrative and
Comparative Biology, 51(1):203213, Jun 2011. 1
[10] Favier J., Pinelli A., and Piomelli U. Control of the
separated ow around an airfoil using a wavy
leading edge inspired by humpback whale ip-
pers. Comptes Rendus Mcanique, 340(1-2):107114,
Jan 2012. 1
[11] Hucho W.H. Aerodynamics of Road Vehicles. Butter-
worth, London, 1978. 8
[12] Hucho W.H. Aerodynamics of Road Vehicles. SAE Inter-
national, Warren, 4th edition, 1998. 8
[13] Kamm W., Schmid C., Riekert P., and Huber L. Ein-
uss der Reichsautobahn auf die Gestaltung der
Kraftfahrzeuge. Automobiltech, 37, 1934. 8
[14] Nye D. Falconer R. Chaparral. Motorbooks Int., Osce-
ole, 1992. 9
[15] Cui E. and Zhang X. Ground Eect Aerodynamics.
Encyclopedia of Aerospace Eng., 2010. 9
[16] Katz J. Aerodynamics of Race Cars. Annu. Rev.
Fluid Mech., 38:2763, 2996. 9
[17] Wright P. The inuence of Aerodynamics on the
design of Formula One racing cars. Int. J. Veh.
Impact Aerodyn. Veh. Des., 3, 1983. 9
[18] Dominy R.G. Aerodynamics of Grand Prix Cars.
Proc Instn Mech Engrs, Part D: J. of Autom. Eng., 206,
1992. 9, 11
[19] Senior A.E. and Zhang X. The force and pressure of
a diuser-equipped blu body in ground eect.
J. of Fluid Eng., 123(1), Mar 2001. 9, 51
[20] Zhang X., Senior A., and Rurhmann A. Turbulence
measurement of vortex ow generated by a blu
body in ground eect. In 5th International Sympo-
sium on Eng. Turbulence Modelling and Measurements
Location, 2002. 9
[21] Ruhrmann A. and Zhang X. Inuence of Diuser An-
gle on a Blu Body in Ground Eect. J. of Fluids
Eng., 125(2):332338, 2003. 9, 51
[22] Zhang X., Senior A., and Rurhmann A. Vortices be-
hind a blu body with an upswept aft section in
ground eect. Int. J. of Heat and Fluid Flow, 25(1):1
9, 2004. 9
[23] Saddington A.J., Knowles R D., and Knowles K. Laser
Doppler anemometry measurements in the near-
wake of an isolated Formula One wheel. Exp. in
Fluids, 42(5):671681, Apr 2007. 9
[24] Axerio-Cilies J. and Iaccarino G. An Aerodynamic
Investigation of an Isolated Rotating Formula 1
Wheel Assembly. J. of Fluids Eng., 134(12), Dec
2012. 9
[25] Heyder-Bruckner J. Aerodynamic Interaction of an In-
verted Wing with a Rotating Wheel. PhD thesis, Univer-
sity of Southampton, 2011. 9
[26] van den Berg M.A. Aerodynamic Interaction of an In-
verted Wing with a Rotating Wheel. PhD thesis, Univer-
sity of Southampton, 2007. 10
[27] Zhang X. Ground Eect Aerodynamics of Race
Cars. Appl Mech Rev., 59:3348, Jan 2006. 10
[28] Jeffrey D. and Alperin M. Aspects of the Aerody-
namics of Year 2000 Formula 1 Racing Cars. In
3rd MIRAl International Vehicle Conference, Oct 2000.
10
[29] Agathangelou B. and Gascoyne M. Aerodynamic con-
siderations of a Formula 1 racing car. Technical
Report 980399, SAE, Warrendale, 1998. 10
65
REFERENCES
[30] Zahm A.F. and Bear R.M. Ground-plane inuence
on airplane wings. J. Franklin Inst, 191(5):687693,
1921. 10
[31] Dominy J.A. and Dominy R.G. Aerodynamic inu-
ences on the performance of the Grand Prix rac-
ing car. Proc Instn Mech Engrs, Part D: J. of Autom.
Eng., 198:17, 1984. 11
[32] Katz J. Calculation of the aerodynamic forces on
automotive lifting surfaces. ASME J. Fluids Eng.,
107(4):438443, 1985. 11
[33] Katz J. Aerodynamics of high-lift, low aspect-
ratio unswept wings. AIAA J., 27(8):11231124,
1989. 11
[34] Coulliette C. and Plotkin A. Aerofoil ground eect
revisited. Aeronaut. J., pages 6574, 1996. 11
[35] Ranzenbach R. and Barlow J. B. Two-Dimensional
Airfoil in Ground Eect, An Experimental and
Computational Study. SAE Paper, 1(94-2509):241
249. 11
[36] Ranzenbach R. and Barlow J. B. Cambered Airfoil
in Ground Eect: Wind tunnel and road condi-
tions. SAE Paper, 1(95-1909):269276, Jun 1995. 11
[37] Ranzenbach R. and Barlow J. B. Cambered Airfoil
in Ground Eect - An Experimental and Com-
putational Study. SAE Paper, 1(96-0909):269276.
11
[38] Diaz R. H. Ranzenbach R., Barlow J. B. Multi-Element
Airfoil in Ground Eect An Experimental and
Computational Study. AIAA Paper, (97-2238), Jun
1997. 11
[39] Knowles K., Donahue D. T., , and Finnis M. V. A Study
of Wings in Ground. In Loughborough University
Conference on Vehicle Aerodynamics, 1994. 11
[40] Neely A.J. Doig G, Barber T.J. The Inuence of Com-
pressibility on the Aerodynamics of an Inverted
Wing in Ground Eect. J. Fluids Eng., 133(06110),
Jun 2011. 12
[41] Zerihan J. and Zhang X. Aerodynamics of a Single-
Element Wing- in-Ground Eect. J. of Aircraft,
37(6):10581064, 2000. 12, 14, 34, 49, 57
[42] Zhang X. and Zerihan J. O-Surface Aerodynamic
Measurements of a Wing in Ground Eect. J. of
Aircraft, 40(4):716725, Jul-Aug 2003. 12, 13
[43] Zhang X. and Zerihan J. Aerodynamics of a Double-
Element Wing in Ground Eect. AIAA J.,
41(6):10071016, Jun 2003. 12
[44] Zhang X. and Zerihan J. Edge Vortices of a Dou-
ble Element Wing in Ground Eect. J. of Aircraft,
41(5):11271137, Sep 2004. 12
[45] Mahon S. and Zhang X. Computational Analysis of
Pressure and Wake Characteristics of an Aero-
foil in Ground Eect. J. Fluids Eng., 127:289297,
mar 2005. 12
[46] Mahon S. and Zhang X. Computational Analysis of a
Inverted Double-Element Airfoil in Ground Ef-
fect. J. Fluids Eng., 128. 12
[47] Soso M.D. and Wilson P.A. Aerodynamics of a wing
in ground eect in generic racing car wake ows.
Proc Instn Mech Engrs, Part D: J. of Autom. Eng., 220.
12
[48] Soso M.D. and Wilson P.A. The inuence of an up-
stream diuser on a downstream wing in ground
eect. Proc Instn Mech Engrs, Part D: J. of Autom.
Eng., 127. 12
[49] Zerihan J. An investigation into the aerodynamics of
wings in ground eect. PhD thesis, University of
Southampton, 2001. 13
[50] Galoul V. and Barber T.J. A study of and inverted
wing with endplates in ground eect. In 16th Aus-
tralasian Fluid Mech. Conference, Oct 2007. 13
[51] Jasinski W.J. and Selig M.S. Experimental Study of
Open-Wheel Race-Car Front Wings. SAE Paper,
Nov. 13
[52] Vogt J.W. and Barber T.J. Ground eect phenom-
ena about lift and downforce generating cam-
bered aerofoils. Int.l J. of Numerical Methods for Heat
& Fluid Flow, 22(2), 2012. 14
[53] Gruschwitz E. and Schrenk O. Uber eine Ein-
fache Moglichkeit zur Auftiebserhohung von
Tragugeln. Zeitschrift fur Flugtechnik und Motor-
luftschiahrt, 20, Oct 1932. 14
[54] Duddy R.R. High Lift Devices and Their Uses. J.
of the Royal Aeronautical Soc., 53(465):859900, 1949.
14
[55] Liebeck R.H. Design of Subsonic Airfoils for High
Lift. J. of Aircraft, 15(9):547561, Sep 1978. 14
[56] Myose R., Papadakis M., and Heron I. Gurney Flap
Exp. on Airfoils, Wings, and Reection Plane
Model. J. of Aircraft, 35(2):206211, Mar 1998. 14
[57] Storms B.L. and Jang C.S. Lift enhancement of an
airfoil using a Gurney ap and vortex genera-
tors. J. of Aircraft, 31(3):542547, May 1994. 14
[58] Jang C.S., Ross J.C., and Cummings R.M. Computa-
tional evaluation of an airfoil with a Gurney ap.
AIAA Paper, (92-2708), Jan 1992. 15
[59] Giguere P., Lemay J., , and G. Dumas. Gurney ap ef-
fects and scaling for low-speed airfoils. In 13th
Applied Aerodynamics Conference, Jun 1995. 15
[60] Jeffrey D., Zhang X., and Hurst D.W. Aerodynamics
of Gurney Flaps on a Single-Element High-Lift
Wing. J. of Aircraft, 37(2):295301, Mar 2000. 15
[61] Jeffrey D., Zhang X., and Hurst D.W. Some As-
pects of the Aerodynamics of Gurney Flaps on a
Double-Element Wing. J. of Fluids Eng., 123(1):99,
2001. 15
66
REFERENCES
[62] Cole J.A., Vieira B.A.O., Coder J.G., Premi A., and
Maughmer M.D. Experimental Investigation into
the Eect of Gurney Flaps on Various Airfoils.
J. of Aircraft, 50(4):12871294, Jul 2013. 16
[63] Ellenrieder K. D. and Pothos S. PIV measurements
of the asymmetric wake of a two dimensional
heaving hydrofoil. Exp. in Fluids, 44(5):733745,
May 2008. 16, 18
[64] Theodorsen T. General theory of aerodynamic in-
stability and the mechanism of utter. (NACA
Tech Report 496), 1935. 17
[65] Garrick I.E. Propulsion of a apping and oscil-
lating airfoil. (NACA Tech Report 567), 1937. 17,
23
[66] Knoller R. Die gesetze des luftwiderstandes. Flug-
und Motortechnik, 3:19, 1909. 17
[67] Betz A. Ein beitrag zur erklarung des segeluges.
Z. Flugtech. Motorluftschiahrt, 3:269272, 1912. 17
[68] von Karman and Burgess J.M. General aerodynamic the-
ory: perfect uids. Springer, 1935. 17
[69] Ohashi H. and Ishikawa N. Visualisation study of ow
near the trailing edge of an oscillating airfoil. Bul-
lettin of the Jap. Soc. of Mech. Eng., 15:840845, 1972.
17
[70] Oshima T. and Oshima K. Vortical ow behind an
oscillating airfoil. In Proceedings of the 15th Interna-
tional Congress, Int. U. of Theor. and App. Mech., pages
357368, 1980. 17
[71] Freymuth P. Propulsive vortical signature of
plunging and pitching airfoils. AIAA J., 26:8881
883, 1988. 17
[72] Triantafyllou G.S., Triantafyllou M.S., and M.A.
Grosenbaugh. Optimal thrust development in os-
cillating foils with application to sh propulsion.
J. of Fluids and Structures, 7:205224, 1993. 17
[73] Koochesfahani M. Vortical Patterns in the wake of
an oscillating airfoil. AIAA J., 27, 1989. 17
[74] Young J. and Lai J.C.S. Oscillation Frequency and
Amplitude Eects on the Wake of a Plunging
Airfoil. AIAA J., 42(10):20422052, Oct 2004. 17
[75] Lai J.C.S. and Platzer M.F. Jet Characteristics of a
Plunging Airfoil. AIAA J., 37(12):15291537, 1999.
17
[76] Triantafyllou M.S. and Grosenbaugh M.A. Prediction
of vortex-induced vibrations in sheared ows. In
6th International Conference on Flow-Induced Vibration,
pages 7382, 1995. 17
[77] Streitlien J. and Triantafyllou G.S. On thrust esti-
mates for apping foils. J. of Fluids and Structures,
12:4755, 1998. 17
[78] Drucker G.E. and Lauder G.V. Locomotor function
of the dorsal n in teleost shes: experimental
analysis of wake forces in sunsh. J. Exp. Biol.,
204(17):29432958, 2001. 18
[79] Wolgang M.J., Amnderson J.M., Grosenbaugh M.A., Yue
D.K.P., and Triantafyllou M.S. Near-body ow dy-
namics in swimming sh. J. Exp. Biol., 202:2303
2327, 1999. 18
[80] Godoy-Diana R., Aider J.-L., and Wesfreid J.E. Transi-
tions in the wake of a apping foil. Physical Rev.
E, 77(1), Jan 2008. 18
[81] He G.-Y., Wang Q., Zhang X., and Zhang S.-G. Nu-
merical analysis on transitions and symmetry-
breaking in the wake of a apping foil. Acta Me-
chanica Sinica, 28(6):15511556, Dec 2012. 18
[82] Lewin G.C. and Haj-Hariri H. Modelling thrust gen-
eration of a two-dimensional heaving airfoil in
a viscous ow. J. of Fluid Mech., 492:339362, Oct
2003. 18
[83] Liang H., Zhou L., Zong Z., and Sun L. An analyti-
cal investigation of two-dimensional and three-
dimensional biplanes operating in the vicinity of
a free surface. J. of Mar. Sc. and Tech., 18(1):1231,
Mar 2013. 18
[84] Shyy et al. Aerodynamics of Low Reynolds Number Fly-
ers. Cambridge Aerospace Series, 2008. 19
[85] McCroskey W.J. and Fisher R.K. Detailed aerody-
namic measurements on a model rotor in the
blade stall regime. J. Amer. Helic. Soc., 17:2030,
1972. 19, 20
[86] Liu H. Simulation-based biological uid dynamics
in animal locomotion. App. Mech. Rev., 58:269282,
2005. 19
[87] Warrick D.R., Tobalske B.W., and D.R. Powers. Aero-
dynamics of the hovering hummingbird. Nature,
435:10941097, 2005. 19
[88] Usherwood J.R. and Ellington C.P. The aerodynam-
ics of revolving wings I. Model hawkmoth wings.
J. Exp. Biol., 205:15471564, 2002. 19
[89] Birch J.M. and Dickinson M.H. Spanwise ow and the
attachment of the leading-edge vortex on insect
wings. Nature, 412:729733, 2001. 19
[90] Ashraf M. A., Young J., and Lai J.C.S. Oscillation Fre-
quency and Amplitude Eects on Plunging Air-
foil Propulsion and Flow Periodicity. AIAA J.,
50(11):23082324, Nov 2012. 19
[91] Medjroubi W., Stoevesandt B., Carmo B., and Peinke
J. High-order numerical simulations of the ow
around a heaving airfoil. Computers and Fluids,
51(1):6884, Dec 2011. 19
[92] Kang C., Aono H., Sik Baik Y., Bernal L.P., and Shyy W.
Fluid Dynamics of Pitching and Plunging Flat
Plate at Intermediate Reynolds Numbers. AIAA
J., 51(2):315329, Feb 2013. 20
67
REFERENCES
[93] Kramer M. Die Zunahme des Maximalauftriebes
von Tragugeln bei plotzlicher Anstellwinkelver-
grosserung (Boeneect). Zeitschrift fur Flugtechnik
und Motorluftschiahrt, 27(7):185189, 1932. 20
[94] Dickinson M.H., Lehmann F.-O., and Sane S.P. Wing ro-
tation and the aerodynamic basis of insect ight.
Sc., 284:19541960, 1999. 21
[95] Sunada S. and Ellington C.P. Approximate added-
mass method for estimationg induced power for
apping ghtt. AIAA J., 38:13131321, 2000. 21
[96] Andro J.-Y. and Jacquin L. Frequency eects on the
aerodynamic mechanisms of a heaving airfoil in
a forward ight conguration. Aerospace Sc. and
Tech., 13(1):7180, Jan 2009. 21
[97] Yu M., Wang Z.J., and Hu H. Airfoil Thickness Eects
on the Thrust Generation of Plunging Airfoils. J.
of Aircraft, 49(5):14341439, Sep 2012. 21
[98] Brunton S.L. and Rowley C.W. Empirical state-space
representations for Theodorsens lift model. J. of
Fluids and Structures, submitted, 2012. 22
[99] Molina J. and Zhang X. Aerodynamics of a Heaving
Airfoil in Ground Eect. AIAA J., 49(6):11681179,
Jun 2011. 23, 26, 28
[100] Gulcat U. Fundamentals of Unsteady Aerodynamics.
Springer, 2010. 23
[101] Dowell E.H. et al. Stall utter. In: Solid Mech. and Its
Applications. Kluwer Academic Publisher, 2004. 23
[102] Dimitriadis G. and Li J. Bifurcation behavior of air-
foil undergoing stall utter oscillations in low-
speed wind tunnel. AIAA J., 47:25772596, 2009.
23
[103] Hodges D.H. and Pierce G.A. Introduction to strc-
tural dynamics and aeroelasticity. 2001. 24
[104] Isaac K.M., Colozza A., and Rolwes J. Force Measure-
ments on a Flapping and Pitching Wing at Low
Reynolds Numbers. In 44th AIAA Aerospace Sc.s
Meeting and Exhibit, 2006. 26
[105] Moryossef Y. and Levy Y. Eect of Oscillations on
Airfoils in Close Proximity to the Ground. AIAA
J., 42(9):17551764, Sep 2004. 26, 44, 52
[106] Molina J., Zhang X, and Angland D. On the un-
steady motion and stability of a heaving airfoil in
ground eect. Acta Mechanica Sinica, 27(2):164178,
Apr 2011. 26
[107] Burgin K., Adey P.C., and Beatham J.P. Wind tun-
nel tests on road vehicles models using a moving
belt simulation of ground eect. J. of Wind Eng.
and Industr. Aerod., 22:227236, 1986. 37
[108] Halfman R.L. Experimental Aerodynamic deriva-
tives of a sinusoidally oscillating airfoil in two-
dimensional owl. (NACA Tech Report 1108), 1952.
47
68
69
70