Sie sind auf Seite 1von 4

64-bit THERMAL HEAD DRIVER

S-4612A

The S-4612A is a CMOS thermal print head driver containing a 64-bit shift register and a latch. It can be used for general purpose because H or L can be selected for the latch and the driver enable. It is ideal for the video printer and the low-voltage-operation thermal print head because of large driver output current and small ON-state resistance.

Features
Low current consumption : 0.4 mA typ.

Driver output current : 70 mA max. 64-bit shift register and latch are built in Driver enable Driver-off function when supply voltage falls Selectable H/L for latch and driver enable

(fCLK=5 MHz, SI : fixed) High speed operation : 7 MHz (chip) 5 MHz (cascade connection)
Driver output voltage : 36 V max.

 Block Diagram
DO1 DO2 DO3 DO63 DO64 VSS1

VDD

AEN BEN VDD

VSS0 LATCH CONT

LA

LA

LA

LA

LA
VSS0

VSS0 SI CLK

D-FF

D-FF

D-FF

D-FF

D-FF

SO

Figure 1

Seiko Instruments Inc.

64-bit THERMAL HEAD DRIVER S-4612A

 Operation
The 64-bit shift register reads the data input to SI on the rising edge of the CLOCK input. The latch circuit operates depending on the levels of CONT and LATCH ; it reads the data of the shift register when the levels of them are the same, and it holds the data of the shift register when they differ. The latch data are output to the respective drivers when AEN is low and BEN is high. The driver output transistor turns on when the latch data are high and turns off when low. Turning AEN high or BEN low makes all driver output transistors go off. All driver output transistors go off when power supply voltage becomes lower than VDET regardless of all input signals.

Terminal Functions (Refer to the dimensions for the pad arrangement)


Table 1
No. Name Functions Driver output terminals (Nch open-drain) GND for driver (0 V) Positive power supply for logic (+5 V) GND for logic (0 V) Clock input terminal for 64-bit shift register Serial data input terminal for 64-bit shift register Serial data output terminal for 64-bit shift register Data latch signal input terminal When CONT=L or open LATCH=L: reads the data of the shift register LATCH=H: holds the preceding data When CONT=H LATCH=L: holds the preceding data LATCH=H: reads the data of the shift register Data latch signal control terminal : selects H or L for LATCH (pull-down resistor is built in) Driver enable terminal : outputs the latch data to the driver when low (pull-up resistor is built in) Driver enable terminal : outputs the latch data to the driver when high (pull-down resistor is built in) Dummy terminals

1 to 64 DO1 to DO64 ( DOn) 65, 68, 71, 74, VSS1 77, 80, 83, 86 67 VDD 75, 81 VSS0 82 CLK 85 SI 66 SO

84

LATCH

76 73 70 69, 72, 78, 79

CONT AEN BEN NC

 Absolute Maximum Ratings


Table 2
Parameter Supply voltage Driver output voltage Driver output current Input voltage Output voltage Max. junction temperature Operating temperature Storage temperature Symbol VSS0,1 - VDD VDOH IDOL VIN VOUT TjMAX Topr Tstg Ratings -0.4 to +7.0 36 70 VSS0-0.5 to VDD+0.5 VSS0-0.5 to VDD+0.5 125 -10 to +80 -40 to +125 Unit V V mA V V C C C

Seiko Instruments Inc.

64-bit THERMAL HEAD DRIVER S-4612A

 DC Electrical Characteristics
Table 3 (Unless otherwise specified : VDD=5.0 V10%, Ta=-10C to 80C)
Parameter Supply voltage High level input voltage Low level input voltage High level input current Sybl VDD VIH VIL IIH IIL Low level input current High level output voltage Low level output voltage High level output current Low level output current High level driver output voltage Low level driver output voltage Driver leakage current Current consumption Lower VDD detection voltage VOH VOL IOH I OL VDOH VDOL IDOL=50 mA, VDD=5.0 V ILEAK IDD VDET VDOH=26 V Per 1-bit of driver output fCLK =2 MHz,SI : fixed Ta= f =5 MHz,SI : fixed 25C CLK fCLK =5 MHz, SI=1/2fCLK VDD=5.0 V BEN, CONT VIH=5.0 V Ta=25C VDD=5.0 V AEN VIL=0 V Ta=25C SO terminal, no load SO terminal, no load SO terminal, VOH=VDD-0.4 V SO terminal, VOL=0.4 V Conditions Min. 4.5 0.7VDD VSS -35 -0.5 4.45 0.5 Typ. 5.0 24 0.5 0.2 0.4 1.6 2.0 Max. 5.5 VDD 0.3VDD 35 0.5 0.05 -0.5 26 1.1 1.0 0.6 1.2 5.0 4.0 Unit V V V A

A A A
V V mA mA V V

A
mA mA mA V

 AC Electrical Characteristics
Table 4
Parameter CLK pulse width Data setup time Data hold time Latch pulse width Latch setup time CLK-SO propagation delay time EN-DOn propagation delay time DOn rise time DOn fall time Clock frequency 1/fCLK CLK SI LATCH LATCH SO AEN BEN DOn tdDO tfDO tdDO trDO
90% 10%

(VDD= 5.0 V10%, Ta=-10C to 80C) Min. 70 50 10 100 100 Typ. 1.7 2.0 Max. 120 6.5 4.5 5.0 5.0 Unit ns ns ns ns ns ns s s s MHz

Symbol tWCLK tSUD tHD tWLA tSULA tdSO tdDO trDO tfDO fCLK

Conditions VIH=VDD, VIL=VSS0 VIH=VDD, VIL=VSS0

CL=3 pF RL=1 k, VDOH=24 V RL=1 k, VDOH=24 V RL=1 k, VDOH=24 V When cascade connection

tWCLK tSUD

tHD tdSO

tSULA

tWLA

Figure 2

Seiko Instruments Inc.

64-bit THERMAL HEAD DRIVER S-4612A

 Dimensions
110 m 1 2 (0,0) 86 83 80 77 74 71 68 65 63 64 1.94 mm *

Pad size : 80 m80 m (passivation opening) Pad pitch : Driver output pad : 110 m Control pad : 200 m min. Chip thickness : 35030 m *Before dicing

85

84 82 81 79 78 3.0 mm

76 75 73 72 70 69 67 66 3.0 mm 7.25 mm *

Figure 3

Pad Coordinates (The origin of the coordinates axes is the center of the chip)
Table 5
Pad No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Name DO1 DO2 DO3 DO4 DO5 DO6 DO7 DO8 DO9 DO10 DO11 DO12 DO13 DO14 DO15 DO16 DO17 DO18 DO19 DO20 DO21 DO22 DO23 DO24 DO25 DO26 DO27 DO28 DO29 X -3465 -3355 -3245 -3135 -3025 -2915 -2805 -2695 -2585 -2475 -2365 -2255 -2145 -2035 -1925 -1815 -1705 -1595 -1485 -1375 -1265 -1155 -1045 -935 -825 -715 -605 -495 -385 Y 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 Pad No. 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 Name DO30 DO31 DO32 DO33 DO34 DO35 DO36 DO37 DO38 DO39 DO40 DO41 DO42 DO43 DO44 DO45 DO46 DO47 DO48 DO49 DO50 DO51 DO52 DO53 DO54 DO55 DO56 DO57 DO58 X -275 -165 -55 55 165 275 385 495 605 715 825 935 1045 1155 1265 1375 1485 1595 1705 1815 1925 2035 2145 2255 2365 2475 2585 2695 2805 Y 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 865 Pad No. 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 Name DO59 DO60 DO61 DO62 DO63 DO64 VSS1 SO VDD VSS1 NC BEN VSS1 NC AEN VSS1 VSS0 CONT VSS1 NC NC VSS1 VSS0 CLK VSS1 LATCH SI VSS1 X 2915 3025 3135 3245 3355 3465 3070 2870 2455 2190 1985 1785 1310 985 785 430 230 30 -450 -870 -1130 -1330 -1535 -1965 -2210 -2420 -2890 -3090 Unit: m Y 865 865 865 865 865 865 -455 -865 -865 -455 -865 -865 -455 -865 -865 -455 -865 -865 -455 -865 -865 -455 -865 -865 -455 -865 -865 -455

Seiko Instruments Inc.

Das könnte Ihnen auch gefallen