Beruflich Dokumente
Kultur Dokumente
33.1
DTGB - 33.1-1-1-10
C
n
o
01/10
Functional features
n
o o
CARLY advantages
Products are compatible with HFCs, HCFCs, CFCs, as well as with their associated oils and additives. Products are designed for use of non-hazardous refrigerants from group 2 of PED 97/23/EC o Product classification in CE categories is performed using the PED 97/23/EC table, corresponding to a volume-based selection. o LCY and LCYE suction line accumulators are designed to ensure optimal separation between the vapour phase and the liquid phase of the refrigerant; only the vapour phase is aspirated by the compressor. o Reduction of the low pressure circuit vibrations.
The pressure drops are low and never go over 0.3C. The heat exchanger allows the increase of the refrigerants refrigerating effect, by high pressure liquid sub-refrigerating, upstream of the pressure relief valve; it therefore prevents the risks of gas presence at the intake of the pressure relief valve. o A hole on the lower part of the inner rod ensures liquid expansion and return to the compressor of the oil that could be trapped inside the suction line accumulator. o A hole on the upper part of the rod is used for safety, in case of excess liquid in the accumulator. o From models LCY 1517 S/MMS and LCYE 1513 S/MMS, presence of a connection on the low part for a return of oil by gravity. o A very large range of suction line accumulators is available, from 0.9 to 70 litres. o GOST certified products.
Non-binding documents
33.2
DTGB - 33.1-1-1-10
01/10
* The capacity of the selected accumulator in kg of refrigerant must be higher than 50% of the installations total refrigerant load. * Mounting should be exclusively performed in vertical position, as close as possible to the compressor and at the same height. * In order to prevent suction line accumulator icing, CARLY recommends to heat insulate them.
* For optimal operation, the refrigerant flow speed in the suction line accumulators rods should be between 8 and 12 m/s; for lower speed values, the oil return to the compressor is unsure. * The LCYE suction line accumulators heat exchanger should be connected in series with the liquid line, between the installations receiver and pressure relief valve.
n SELECTION
"MINIMUM refrigerating capacity" selection curves, according to the refrigerant used (refer to pages 33.4 and 33.5) Carry forward on the curve the installations refrigerating capacity and the evaporation temperature: the operating point should be above the curve of the accumulator selected. If this is not the case, choose a smaller accumulator.
Non-binding documents
33.3
DTGB - 33.1-1-1-10
C
(1)
01/10
The sizing of a product implies for the buyer to take into account the conditions under which the product will be used (temperature pressure - refrigerant - oil - external environment). The values of the selection tables proposed in the CARLY catalogue match accurate test conditions. Installation operating with R404A under the following conditions(1): To = -10C Tk = 30C Qox = 8 kW Capacity of refrigerant at 30C of the circuit = 5 kg Suction piping = 7/8 Which LCY suction line accumulator to choose?
CARLY references
LCY 27 S LCY 47 S
CARLY references
LCY 27 MMS LCY 47 MMS
Capacity of accumulator (kg of refrigerant at 30C) R22 R407C 1,7 2,5 R134a 1,8 2,6 R410A R404A R507 1,8 2,6
7/8 7/8
22 22
Result : Among the 2 pre-selected references, the LCY 47 S accumulator should be selected because its capacity in kg of refrigerant (2.6 kg) is higher than half the installations total refrigerant load (2.5 kg).
33.4
DTGB - 33.1-1-1-10
Refrigerating capacity in kW
Refrigerating capacity in kW
01/10
CONNECTIONS
inch 3 5/8 3 1/8 2 5/8 2 1/8 1 5/8 1 3/8 1 1/8 7/8 3/4 5/8 1/2 mm 88,9 80,0 67,0 54,0 42,0 35,0 28,0 22,0 18,0 16,0 12,0
100,00
LCY 813 - LCY 1013 - LCYE 1013 LCY 611 - LCY 811 - LCY 1011 - LCYE 811 LCY 49 - LCY 69 - LCY 89 - LCYE 69 LCY 27 - LCY 47 - LCYE 47 LCY 16 - LCY 26 - LCYE 26 LCY 15 - LCY 25 - LCYE 25 LCY 04 - LCY 14
10,00
1,00
Evaporation temperature in C
CARLY REFERENCES
LCY 7029 LCY 3625 - LCY 5025 - LCY 7025 - LCYE 3625 LCY 3621 - LCY 5021 - LCYE 3621 LCY 1517 - LCY 1817 - LCY 3617- LCYE 1517 LCY 813 - LCY 1013 - LCYE 1013 LCY 611 - LCY 811 - LCY 1011 - LCYE 811 LCY 49 - LCY 69 - LCY 89 - LCYE 69 LCY 27 - LCY 47 - LCYE 47 LCY 16 - LCY 26 - LCYE 26
CONNECTIONS
inch 3 5/8 3 1/8 2 5/8 2 1/8 1 5/8 1 3/8 1 1/8 7/8 3/4 5/8 1/2 mm 88,9 80,0 67,0 54,0 42,0 35,0 28,0 22,0 18,0 16,0 12,0
10,00
1,00
Evaporation temperature in C
Non-binding documents
33.5
DTGB - 33.1-1-1-10
Refrigerating capacity in kW
Refrigerating capacity in kW
01/10
100,00
LCY 1517 - LCY 1817 - LCY 3617- LCYE 1517 LCY 813 - LCY 1013 - LCYE 1013 LCY 611 - LCY 811 - LCY 1011 - LCYE 811 LCY 49 - LCY 69 - LCY 89 - LCYE 69
10,00
LCY 27 - LCY 47 - LCYE 47 LCY 16 - LCY 26 - LCYE 26 LCY 15 - LCY 25 - LCYE 25 LCY 04 - LCY 14
1,00
Evaporation temperature in C
CARLY REFERENCES
CONNECTIONS
inch mm
LCY 7029 LCY 3625 - LCY 5025 - LCY 7025 - LCYE 3625 LCY 3621 - LCY 5021 - LCYE 3621 LCY 1517 - LCY 1817 - LCY 3617- LCYE 1517
10,00
3 5/8 3 1/8 2 5/8 2 1/8 1 5/8 1 3/8 1 1/8 7/8 3/4 5/8 1/2
88,9 80,0 67,0 54,0 42,0 35,0 28,0 22,0 18,0 16,0 12,0
LCY 813 - LCY 1013 - LCYE 1013 LCY 611 - LCY 811 - LCY 1011 - LCYE 811
LCY 49 - LCY 69 - LCY 89 - LCYE 69 LCY 27 - LCY 47 - LCYE 47 LCY 16 - LCY 26 - LCYE 26
1,00
Evaporation temperature in C
Non-binding documents
33.6
DTGB - 33.1-1-1-10
01/10
table
Connections To solder ODF
inch
CARLY references
CARLY references
Capacity of accumulator (kg of refrigerant at 30C) R22 R407C 0,7 1,1 1,1 1,1 1,7 1,7 1,7 2,5 3,2 4,8 6,5 4,8 6,5 6,5 8,6 8,6 14,0 18,5 33,0 33,0 33,0 47,0 47,0 65,5 65,5 R134a 0,7 1,2 1,2 1,2 1,8 1,8 1,8 2,6 3,2 4,9 6,6 4,9 6,6 6,6 8,7 8,7 14,5 19,0 33,5 33,5 33,5 47,5 47,5 67,0 67,0 R410A R404A R507 0,7 1,2 1,2 1,2 1,8 1,8 1,8 2,6 3,2 4,9 6,6 4,9 6,6 6,6 8,7 8,7 14,5 19,0 33,5 33,5 33,5 47,5 47,5 67,0 67,0
LCY 04 S LCY 14 S LCY 15 S/MMS LCY 16 S LCY 25 S/MMS LCY 26 S LCY 27 S LCY 47 S LCY 49 S LCY 69 S LCY 89 S LCY 611 S/MMS LCY 811 S/MMS LCY 813 S LCY 1011 S/MMS LCY 1013 S LCY 1517 S/MMS LCY 1817 S/MMS LCY 3617 S/MMS LCY 3621 S LCY 3625 S LCY 5021 S LCY 5025 S LCY 7025 S LCY 7029 S
1/2 1/2 5/8 3/4 5/8 3/4 7/8 7/8 1 1/8 1 1/8 1 1/8 1 3/8 1 3/8 1 5/8 1 3/8 1 5/8 2 1/8 2 1/8 2 1/8 2 5/8 3 1/8 2 5/8 3 1/8 3 1/8 3 5/8
LCY 04 MMS LCY 14 MMS LCY 15 S/MMS LCY 16 MMS LCY 25 S/MMS LCY 26 MMS LCY 27 MMS LCY 47 MMS LCY 49 MMS LCY 69 MMS LCY 89 MMS LCY 611 S/MMS LCY 811 S/MMS LCY 813 MMS LCY 1011 S/MMS LCY 1013 MMS LCY 1517 S/MMS LCY 1817 S/MMS LCY 3617 S/MMS LCY 3621 MMS LCY 3625 MMS LCY 5021 MMS LCY 5025 MMS LCY 7025 MMS LCY 7029 MMS
12,0 12,0 16,0 18,0 16,0 18,0 22,0 22,0 28,0 28,0 28,0 35,0 35,0 42,0 35,0 42,0 54,0 54,0 54,0 67,0 80,0 67,0 80,0 80,0 88,9
Non-binding documents
33.7
DTGB - 33.1-1-1-10
01/10
features
Dimensions (mm) Drawing Nb 1 1 1 LCY 16 MMS LCY 26 MMS LCY 27 MMS LCY 47 MMS LCY 49 MMS LCY 69 MMS LCY 89 MMS 1 1 1 1 1 2 2 2 2 2 LCY 813 MMS LCY 1013 MMS 2 2 2 3 3 3 LCY 3621 MMS LCY 3625 MMS LCY 5021 MMS LCY 5025 MMS LCY 7025 MMS LCY 7029 MMS 3 3 3 3 3 3 Possible retention volume (L) 0,09 0,09 0,10 0,12 0,13 0,12 0,14 0,14 0,16 0,21 0,21 0,25 0,25 0,25 0,25 0,25 0,48 0,48 1,60 1,80 2,10 1,80 2,10 2,10 2,30 Net weight (kg) 1,20 1,70 1,80 1,95 3,15 3,20 3,30 4,35 5,60 8,20 9,85 9,10 11,20 11,60 13,65 14,25 20,35 25,20 41,40 45,70 47,35 57,10 59,10 75,00 79,00
CARLY references
LCY 04 S LCY 14 S LCY 15 S/MMS LCY 16 S LCY 25 S/MMS LCY 26 S LCY 27 S LCY 47 S LCY 49 S LCY 69 S LCY 89 S LCY 611 S/MMS LCY 811 S/MMS LCY 813 S LCY 1011 S/MMS LCY 1013 S LCY 1517 S/MMS LCY 1817 S/MMS LCY 3617 S/MMS LCY 3621 S LCY 3625 S LCY 5021 S LCY 5025 S LCY 7025 S LCY 7029 S LCY 04 MMS LCY 14 MMS
1
89,0 89,0 89,0 89,0 101,6 101,6 101,6 101,6 121,0 152,4 152,4 152,4 152,4 152,4 152,4 152,4 219,1 219,1 323,9 323,9 323,9 323,9 323,9 323,9 323,9
L 208,0 299,0 299,0 299,0 363,0 363,0 373,0 487,0 464,5 433,5 533,5 439,0 539,0 539,0 647,0 647,0 631,5 781,5 727,0 727,0 727,0 927,0 927,0 1177,0 1177,0
2
/ / / / / / / / / / / / / / / / 190 190 290 290 290 290 290 290 290
8X
M10x25
M12x25
Non-binding documents
1/2 NPTF
33.8
DTGB - 33.1-1-1-10
C
(1) (2)
01/10
features
Maximal working pressure PS (bar) 42 42 42 42 20 20 28 20 30 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 Working pressure
(1)
CARLY references
Volume
Minimal working temperature TS mini (C) -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40
Working temperature
(1)
CE Category
(2)
V (L) LCY 04 S LCY 14 S LCY 15 S/MMS LCY 16 S LCY 25 S/MMS LCY 26 S LCY 27 S LCY 47 S LCY 49 S LCY 69 S LCY 89 S LCY 611 S/MMS LCY 811 S/MMS LCY 813 S LCY 1011 S/MMS LCY 1013 S LCY 1517 S/MMS LCY 1817 S/MMS LCY 3617 S/MMS LCY 3621 S LCY 3625 S LCY 5021 S LCY 5025 S LCY 7025 S LCY 7029 S LCY 3621 MMS LCY 3625 MMS LCY 5021 MMS LCY 5025 MMS LCY 7025 MMS LCY 7029 MMS LCY 1013 MMS LCY 813 MMS LCY 26 MMS LCY 27 MMS LCY 47 MMS LCY 49 MMS LCY 69 MMS LCY 89 MMS LCY 16 MMS LCY 04 MMS LCY 14 MMS 0,90 1,50 1,50 1,50 2,20 2,20 2,20 3,20 4,20 5,80 7,40 5,80 7,47 7,51 9,27 9,30 15,20 20,20 35,39 35,61 35,89 50,61 50,89 70,89 71,15
PS BT (bar) 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10
TS BT (C) -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 Art 33 I I I Art 33 Art 33 I I I I I I I I I I II II II II II III III III III
The working pressure is limited to the PS BT value when working temperature is lower than or equal to TS BT value. Classification by volume, according to PED 97/23/EC (refer to chapter 0 page 7).
Non-binding documents
33.9
DTGB - 33.1-1-1-10
01/10
table
Connections To solder ODF
inch
CARLY references
CARLY references
Capacity of accumulator (kg of refrigerant at 30C) R22 R407C 1,7 1,7 2,5 4,8 6,5 8,6 14,0 33,0 33,0 R134A 1,8 1,8 2,6 4,9 6,6 8,7 14,5 33,5 33,5 R410A R404A R507 1,8 1,8 2,6 4,9 6,6 8,7 14,5 33,5 33,5
LCYE 25 S LCYE 26 S LCYE 47 S LCYE 69 S LCYE 811 S/MMS LCYE 1013 S LCYE 1517 S LCYE 3621 S LCYE 3625 S n Technical
LCYE 25 MMS LCYE 26 MMS LCYE 47 MMS LCYE 69 MMS LCYE 811 S/MMS LCYE 1013 MMS LCYE 1517 MMS LCYE 3621 MMS LCYE 3625 MMS
16 18 22 28 35 42 54 67 80
10 10 12 16 16 18 22 28 35
features
Dimensions (mm) Drawing Nb Possible retention volume (L) 0,13 0,12 0,14 0,21 0,25 0,25 0,48 1,80 2,10 Net weight (kg)
CARLY references
LCYE 25 S LCYE 26 S LCYE 47 S LCYE 69 S LCYE 811 S/MMS LCYE 1013 S LCYE 1517 S LCYE 3621 S LCYE 3625 S LCYE 25 MMS LCYE 26 MMS LCYE 47 MMS LCYE 69 MMS LCYE 811 S/MMS LCYE 1013 MMS LCYE 1517 MMS LCYE 3621 MMS LCYE 3625 MMS
1
101,6 101,6 101,6 152,4 152,4 152,4 219,1 323,9 323,9
2
/ / / / / / 190 290 290
4 4 4 5 5 5 6 6 6
8X
M10x25
Non-binding documents
1/2 NPTF
33.10
DTGB - 33.1-1-1-10
C
(1)
01/10
features
Maximal working pressure PS (bar) 43 43 43 20 20 20 20 20 20 Working pressure
(1)
CARLY references
Volume
Minimal working temperature TS mini (C) -40 -40 -40 -40 -40 -40 -40 -40 -40
Working temperature
(1)
CE Category
(2)
V (L) LCYE 25 S LCYE 26 S LCYE 47 S LCYE 69 S LCYE 811 S/MMS LCYE 1013 S LCYE 1517 S LCYE 3621 S LCYE 3625 S LCYE 25 MMS LCYE 26 MMS LCYE 47 MMS LCYE 69 MMS LCYE 811 S/MMS LCYE 1013 MMS LCYE 1517 MMS LCYE 3621 MMS LCYE 3625 MMS 2,30 2,30 3,20 5,80 7,50 9,30 15,20 35,61 35,00
PS BT (bar) 10 10 10 10 10 10 10 10 10
TS BT (C) -20 -20 -20 -20 -20 -20 -20 -20 -20 I I I I I I II II II
The working pressure is limited to the PS BT value when working temperature is lower than or equal to TS BT value. (2) Classification by volume, according to PED 97/23/EC (refer to chapter 0 page 7).
n Weights
LCY 04 S & MMS LCY 14 S & MMS LCY 15 S/MMS LCY 16 S & MMS LCY 25 S/MMS LCY 26 S & MMS LCY 27 S & MMS LCY 47 S & MMS LCY 49 S & MMS LCY 69 S & MMS LCY 89 S & MMS LCY 611 S/MMS LCY 811 S/MMS LCY 813 S & MMS LCY 1011 S/MMS LCY 1013 S & MMS LCY 1517 S/MMS
LCY / LCYE
and packaging
Unit weight (kg) Without With packaging packaging 1,28 1,78 1,85 2,03 3,55 3,60 3,70 3,40 6,00 7,55 10,20 9,45 10,60 11,95 14,25 14,85 20,85 1,20 1,70 1,75 1,95 3,15 3,20 3,30 3,15 5,60 7,25 9,85 9,10 10,40 11,60 13,65 14,25 20,35 Packaging unit standard 6 6 6 6 1 1 1 1 1 1 1 1 1 1 1 1 1 OEMS 24 / / 15 8 / 8 4 / / / / / / / / /
CARLY references
CARLY references
LCY 1817 S/MMS LCY 3617 S/MMS LCY 3621 S & MMS LCY 3625 S & MMS LCY 5021 S & MMS LCY 5025 S & MMS LCY 7025 S & MMS LCY 7029 S & MMS LCYE 25 S & MMS LCYE 26 S & MMS LCYE 47 S & MMS LCYE 69 S & MMS LCYE 811 S/MMS LCYE 1013 S & MMS LCYE 1517 S & MMS LCYE 3621 S & MMS LCYE 3625 S & MMS
OEMS
/ / / / / / / / / / / / / / / / /
Non-binding documents