Beruflich Dokumente
Kultur Dokumente
WKM
DISTRIBUTED VALVES
TABLE OF CONTENTS
DIMENSIONAL DATA
4 in. (100 mm) Reduced Port and Smaller Features and Benefits Exploded View Trim Chart 14 & 15 16 & 17 18 19
DIMENSIONAL DATA
4 in. (100 mm) Full Port and Larger Pressure/Temperature Charts Weights Flow Characteristics Stem Torques SERIES 310 Material Selection Guide 20 & 21 22 & 23 24 & 25 25 26 & 27 28 through 34 35 36
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
Ductile Iron 1
Buna FKM
1 2
0 1 2 3
2000 psi 4
Size
(mm)
Base Number 24925 25144 24926 25145 Acetal Plastic (43) 3 2 x 1 1/2 & 3 x 2 (50 x 40) & (80 x 50) Filled Teflon (42) 5 2 x 1 1/2 & 3 x 2 (50 x 40) & (80 x 50) Carbon Steel Stainless Steel 1 2
1500/2000# MOP
* Maximum pressure rating of 1500 psi for 4 in. x 3 in. (100 mm x 80 mm) and 3 in. x 3 in. (80 mm x 80 mm).
25111 25112
Examples:
Standard Trim 2 in. (50 mm) J024925-2131100 H2S, NACE trim suffix code = standard -213220X = unidirectional -213240X
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
Production wing valves on low pressure gas wells Production flow lines Production gathering systems for water, oil and gas Gas blow down service Tank batteries for storage or production Frac water tanks
Open or closed position locking handle. Handle provides positive indication of open/ closed position.
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
FIRE TESTED DESIGN The W-K-M DynaSeal 210 ball valves are qualified under API Standard 607 except the 4 in. x 3 in. (100 mm x 80 mm) 750 and 1000 psi valves. The deep pocketed seat, locked in stem and body/tailpiece designs give this valve excellent fire tested characteristics. (The 4 in. x 3 in. (100 mm x 80 mm) 750 and 1000 psi valves do not have deep pocketed seats). SUPERIOR STEM JOURNAL DESIGN PREVENTS STEM SEIZURE The stem is designed with two internal O-ring grooves located on either side of a shallow grease groove. The top O-ring is a weather seal while the bottom one seals the stem bore against the line media. The stem gasket provides a backup seal. The shallow groove between the O-rings provides three benefits: prevents stem seizure reduces torque provides a space for lubricating grease applied at the factory during assembly. TFE BODY SEAL A TFE body seal is positioned between the line bore and tailpiece threads isolating the threads from the line media. DEEP RECESSED SEATS The seat is recessed into a deep machined pocket, which serves to surround and protect the seat on all sides. This design eliminates cold flow into the valve conduit where it can be damaged by the action of the ball or the flow medium. The result is extremely long service life. (Seats are not recessed in the 4 in. x 3 in. (100 mm x 80 mm) 750 and 1000 psi valves).
DEMCO/W-K-M introduced the unidirectional valve option in 1979 to provide relief to valves that might have water trapped in the body cavity and then be exposed to a temporary freeze. Since this option relies on a relief hole in the ball to relieve the excess pressure the valve is stamped with a directional flow arrow to be sure the side of the ball with the hole is installed upstream.
SEAL PIN DEVICE PROVIDED AS STANDARD ON 750 AND 1000 psi, 2 in., 3 in. AND 4 in. (50 mm, 80 mm AND 100 mm) REDUCED PORT VALVES. A secondary seal pin device for applying tamper detection seals is provided on these valves. These valves are a popular choice for production tank batteries where tamper detection seals are often required.
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
SERIES 210 1 in. (25 mm) FULL PORT THROUGH 4 in. x 3 in. (100 mm x 80 mm) REDUCED PORT
Handle (Optional) Bolt Dart and Chain Retainer Ring Locking Plate Stop Pin Body Wave Spring
Stem
Ball
Tailpiece Gasket
Tailpiece
Seat Rings
UNIDIRECTIONAL BALL
WORKING PRESSURE
SIZE in. 1 (mm)
(25) FP
OPTIONAL MATERIALS
COMPLIANCES
(100 x 80) RP
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
SERIES 210 1 in. (25 mm) FULL PORT THROUGH 4 in. x 3 in. (100 mm x 80 mm) REDUCED PORT 750, 1000, 1500 and 2000 psig WORKING PRESSURE
STANDARD MATERIALS
Qty.
1 1 1 1 2
DESCRIPTION
Body Tailpiece Ball Stem Seat Ring
MATERIAL
ASTM A395 Ductile Iron ASTM A395 Ductile Iron Carbon Steel Chrome Plated 316 SS AISI 1213/1215, Steel, Zinc Plated 316 SS (17-4PH SS on 2 in. x 1 1/2 in. (50 mm x 40 mm) Acetal Plastic (43) Filled TFE (42) Carbon Filled TFE (2) 750/1000 psi PTFE Buna-N FKM Filled TFE Steel 1018/26 Spring Steel Spring Steel Spring Steel
1 2 1 1 1 1 1 1 1
Tailpiece Gasket Stem O-Ring Stem Gasket (Thrust Bearing) Locking Plate Locking Plate Retaining Ring Wave Spring Stop Pin Handle
1 in. (25 mm ) FP & 2 in. x 1 1/2 in. (50 x 40): Carbon Steel, Zinc Plated 2 in. (50 mm) FP through 4 in. x 3 in. (100 x 80): ASTM A395 Ductile Iron Nut on 1 in. (25 mm) Retainer Ring on 2 in. x 1 1/2 in. (50 mm x 40 mm) Bolt on 2 in. (50 mm) FP through 4 in. x 3 in. (100mm x 80 mm) Brass or Aluminum
Handle Retainer
Seal Pin/Dart
Note: For H2S service use Trim Code -X13220X. Meets NACE MR0175 (Rev. 2002) (see How To Order page 1).
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
F E E
BORE DIA
BORE DIA
C
PIPE
DIMENSIONAL DATA
SIZE in.
1 FP 2 RP 2 FP 2 1/2 RP 3 RP 3 FP 4 RP
B
1.00 1.50 2.00 2.00 2.00 3.00 3.00 25 38 51 51 51 76 76
G
7.1 7.1 15.0 15.0 15.0 15.0 15.0 180 180 381 381 381 381 381
SIZE mm
25 FP 50 RP 50 FP 65 RP 80 RP 80 FP 100 RP
1x1
4.0 4.5
2x2
14.4 17.6
3x3
42.8 46.0
25 x 25
1.8 2.0
50 x 50
6.5 8.0
80 x 80
19.4 20.9
2 x 1 1/2
9.4 9.9
2 1/2 x 2
15.5 18.0
3x2
16.6 19.8
4x3
35.5 38.7
50 x 40
4.3 4.5
65 x 50
7.0 8.2
80 x 50
7.5 9.0
100 x 80
16.1 17.6
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
Material Carbon Steel Controlled hardness carbon steel for H2S service Same as CS2, but special for -50F (-46C) service 316 stainless steel for wetted parts 316 stainless steel with stainless steel external trim. Good for -50F (-46C).
* Meets NACE *MR0175 (Rev. 2002)
Code CS S1 ML S2*
* NACE 4 in. (100 mm) RP and smaller. 17-4 PH Stem, 316 Stainless Steel Ball.
Actuator Code Seal Number 01 42 43 07 18 23 28 48 60 92H Seal Material PTFE Filled PTFE Homopolymer Acetal Plastic FKM HPT-2 Celcon Filled PTFE Homopolymer Acetal Plastic Stellite 316 SS with Chrome Carbide & Filled PTFE Tailpiece Gasket Material PTFE PTFE PTFE PTFE Filled PTFE PTFE Filled PTFE Filled PTFE Filled PTFE Filled PTFE
310 2-PIECE VALVE TYPES SIZE in. (mm)
1/4 3/8 (8) FP (20) FP (15) RP (15) FP (20) FP (25) RP (25) FP (50) RP (50) FP (80) FP (100) RP
Wrench* Oval Handwheel Worm Gear Bare Stem Less Gear Less Wrench
WR OH WG BS LG LW
* Wrenches are part of the valve assembly in 1 1/2 in. (40 mm) bore size and smaller valves. In 2 in. (50 mm) bore size and larger, they are sold separately.
1/2
600 RJ
B172 B172 B170 B172 B170 B172 B170 B172*** B170*** B172*** B170*** -
1/2 3/4 1 1 2 2 3 4
1 1/2 (40) FP
3 x 2 (80 x 50) RP
** Available in Body Tailpiece Code S8 Only. Note: Threaded end valves have NPT internal pipe thread in full conformance with ASME/ANSI B2.1 and Federal Thread Handbook H-28.
SOCKET WELD
B103 B106 B103 B106 B103 B106
1 1/2 (40) FP
* LP is Long Pattern, SP is Short Pattern. ** Unibody style valve. *** The 4 in. (100 mm) and larger sizes are available in trim CS2-43-S2-WGA (Worm Gear Operated) only.
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
This chart is an abbreviated guide to the chemical resistance and pressure/temperature limitations of the seal materials used in the 310 valve series. Consult your DynaSeal distributor or the W-K-M factory regarding questions about trim selections.
SEAL CODE 01
SERVICE APPLICATION Seat and Tailpiece gaskets are of virgin TFE. Use where lading contamination from glass or other fillers is not desirable, such as in food service. Recommended for low temperature service to -50F (-46C). Also recommended for vacuum service. Seat material is TFE filled with inert materials for use at elevated temperatures and pressures. Same chemical resistance as Virgin TFE except slightly affected by hot concentrated alkaline solutions. Some chlorinated compounds can cause swelling. Also recommended for low temperature service -50F (-46C). Good for vacuum service. For general use at high pressures to temperature of 220F (104C). For general use at high pressures to temperature of 220F (104C). Used on socket weld end valves 3 in. (80 mm) bore size and smaller. High and low pressure block and bleed. General use for low pressure and abrasion resistance. Not suitable for steam. Good for vacuum service. Available in bore sizes to 3 in. (80 mm). HPT-2 is a special TFE formulation for use at temperatures above trim 42 capability. Best suited for constant temperature or constant pressure applications. Proven service in steam, hot oil, heat transfer fluids, hot resins, boiler feed water. Same chemical resistance as TFE. Slightly affected by hot, concentrated alkaline solutions. Some fluorinated compounds cause swelling. For use in high pressure applications. Temperature limited to 225F (107C) (1/4 in. to 3/4 in. (8 mm to 20 mm) bores only). Same as 42 except tailpiece gasket is filled TFE. Used on weld end valves 4 in. (100 mm) and larger. Special Stellite seats for use when hard faced metal seats are required for industrial applications including the pulp and paper industry. Leakage Class V. For temperatures to 600F (316C). For slurries, abrasives, steam, hot water. Leakage Class V.
42
Filled TFE
TFE
43 48 07
18
HPT-2
Filled TFE
23
Celcon
TFE
28 60
92H
Note 1: Trim 07 and 18 should be tested for each application by actual use. Note 2: All seal codes with the exception of 07, 60 and 92H have been fire tested (and qualified) to API 607 4th Edition requirements. * Trim sizes smaller than 1 1/2 in. (40 mm) in trim 07 are 100% elastomeric. Sizes 1 1/2 in. (40 mm) and larger are elastomeric with a metal insert.
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
Stem is positively retained, cannot be removed with valve in service. Floating ball is self adjusting, self cleaning.
Seat is in deep protective pocket which prevents cold flow of seat into line
FLANGED VALVE ASSEMBLY 1 in. (25 mm) FULL PORT THROUGH 4 in. x 3 in. (100 mm x 80 mm) REDUCED PORT.
Open or closed position locking plate allows use of popular padlock designs.
Floating ball is self adjusting, self cleaning. 2 piece bolted body API 607 4th Edition fire tested. Seat is in deep protective pocket which prevents cold flow of seat into line.
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
SERIES 310
W-K-M DynaSeal 310 floating ball valves satisfy a wide range of applications. Available in a variety of standard and optional materials, in sizes from 1/4 in. (8 mm) to 4 in. x 3 in. (100 mm x 80 mm) and working pressures to 5000 psi. Engineered for heavy duty, maintenance free performance, the DynaSeal 310 valve is preferred for use in critical applications. SOUR OIL AND GAS SERVICE DynaSeal ball valves have served for years in gathering lines, manifolds and field processing units in sour oil and gas fields. They can be trimmed to conform with NACE MR0175 (Rev. 2002).
FLOATING BALL DESIGN DELIVERS TIGHT SEAL The ground and polished ball is free to float and mates perfectly with the conical seats for a positive, leakproof seal. Self cleaning and self adjusting, the ball is also pressure activated - the higher the line pressure, the tighter the seal.
310 Unibody 1/2 in., 3/4 in. x 1/2 & 1 in. x 3/4 in. (15 mm, 20 mm x 15 mm and 25 mm x 20 mm) Class 150 & 300 Flanged.
FIRE-TESTED FOR SAFETY All DynaSeal 310 valves are qualified under API standard 607 4th Edition. The pocketed seat and locked in stem design contributes to its excellent fire tested characteristics. Should the soft seats be destroyed by fire, the ball floats down stream, providing a tight metal to metal seal against the lip of the seat pocket. If the tailpiece seals are destroyed, the metal to metal tailpiece to body connection retards external leakage.
CONICAL SEAT
PRESSURE HERE
METAL SHOULDER
TRIM 42 SEAT
TRIM 43 SEAT
INDICATOR HANDLE The design of the handle permits installation on the stem in the correct position only, in alignment with the ball port. When the handle is aligned with the pipe, the valve is open. When the handle is perpendicular to the pipe, the valve is closed. LOCKING DEVICES Locking devices are standard on all 4 in. x 3 in. (100 mm x 80 mm) and smaller manually operated valves and permit locking in either the open or closed positions.
ADJUSTABLE PACKING
10
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
SERIES 310
SOCKET WELD ENDS
STANDARDS AND SPECIFICATIONS
Lock Nut
Sizes: 1/4 in. (8 mm) Full Port 1/2 in. (15 mm) Reduced Port
Handle
3/4 in. (20 mm) Full Port 1 in. (25 mm) Reduced Port 1 1/2 in. (40 mm) Full Port 2 in. (50 mm) Reduced Port.
Cap Screw
Tailpiece
Bonnet Cap
WORKING PRESSURE
3000 psi with Trim 48 From -20F to 220F (-29C to 104C). Socket Weld Ends.
Body: Carbon Steel and Carbon Steel NACE MR0175 (Rev. 2002). Ball/Stem: Carbon Steel or Stainless Steel. Seats: Trim 48(Acetal Plastic Seats).
PRESSURE CLASS
Body Stop Plate Cap Screw
STANDARD MATERIAL
Packing Stem Seal Stem
Body: Carbon Steel, CF8M SS. Ball/Stem: Carbon Steel, 316 SS/17-4PH. Seats: Select from page 8.
Ball
OPTIONAL MATERIALS
Bodies, Stems & Balls can be offered in different alloys - Consult Factory. Seat Materials: High Temp TFE, FKM, Stellite, Chromium Carbide Coated, Acetal Plastic.
WKM
CT-WKM-210/310
10/06 NP-2M
11
DISTRIBUTED VALVES
SERIES 310
Lock Nut
THREADED CONNECTIONS
Handle Cap Screw
Bonnet Cap
Cap Screw
THREADED ENDS
1/4 in. (8 mm) FULL PORT - 1 in. (25 mm) REDUCED PORT
Lock Nut Compression Ring Tailpiece Packing Stem Seal Stem Stop Plate Bonnet Cap Cap Screws Body Tailpiece Gasket Seat Ring Ball Seat Ring Handle
2 3
OPERATING TEMPERATURES
From -50F to 600F (-46C to 316C)
STANDARD MATERIAL
Body: Carbon Steel and Stainless Steel Ball/Stem: Carbon Steel, Stainless Steel and Monel
FLANGED ENDS
Seat/Seal Trims:
Retainer Ring Compression Ring Packing
TFE, Filled TFE, Acetal Plastic, HPT-2, 316 Stainless Steel with Chromium Carbide and FKM
Handle
Tailpiece
INDUSTRY COMPLIANCE:
ASME/ANSI B16.5, B16.34 MSS-SP-6, 25, 55, 72 API 607 4th Edition (Fire Test Specification)
Stop Plate Cap Screws Bonnet Cap Body Stud Nut Body Stud Ball Seat Ring Tailpiece Gasket Body
150
(100 x 80) RP
12
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
SERIES 310
1/4 in. (8 mm) FULL PORT THROUGH 4 in. (100 mm) REDUCED PORT MATERIALS LIST - THREADED AND FLANGED ENDS
CS
ASTM A105/A216 Gr. WCC A193 Gr. B7 A194 Gr. 2H Carbon Steel ASTM A105/A216 Gr. WCC*** Stainless Steel Carbon Steel Alloy Steel Plated
CS2*
ASTM A105/A216 Gr. WCC A193 Gr. B7M A194 Gr. 2HM Carbon Steel ASTM A105/A216 Gr. WCC Stainless Steel Carbon Steel 18-8 SS
CS3*
ASTM A350 LF2 A320 Gr. L7M A194 Gr. 7ML Carbon Steel ASTM A350 LF2 Stainless Steel Carbon Steel 18-8 SS
S8*
316 SS/A351 CF8M A193 Gr. B8 A194 Gr. 8 Stainless Steel 316 SS/A351 CF8M Stainless Steel Stainless Steel 18-8 SS
* CS2/CS3/S8 to be used for H2S service with S2 internal trim only. Meets NACE MR0175 (Rev. 2002). ** When body drain is specified. *** AISI 1018 Seat Retainers are used in 1/2 in., 3/4 in. and 1 x 3/4 in. (15 mm, 20 mm and 25 mm x 20 mm) Class 150 and 300 unibody valves.
01
TFE TFE TFE
23**
Celcon TFE
42
Filled TFE TFE
43
Acetal Plastic TFE
48***
Acetal Plastic Filled TFE
07
FKM TFE Filled TFE
18
Special Filled TFE Filled TFE
60*
Stellite Filled TFE
92H*
316 SS Chromium Carbide Coated Filled TFE
CS
AISI 1213 CS Chrome Plate AISI 1213 Zinc Plate 304 SS
S1
316 SS 316 SS 304 SS
S2*
316SS 17-4 PH 304 SS
ML
B164 Class B Ni-Cu Alloy B 164 Class B Ni-Cu Alloy 304 SS
Note: *S2 Trim (17-4 PH Stem & 316 SS Ball) is required for H2S service per NACE MR0175 (Rev. 2002) to be used with Body/Tailpiece codes CS2/CS3/S8.
ACTUATOR CODE
PART (BODY) Lock Nut* Handle* Handle Grip* Wrench Handle** Wrench Head Bolt & Nut** Stop Plate
* **
CS
Alloy Steel CS Zinc Plated Vinyl Ductile Iron Alloy Steel Stainless Steel
CS2
Alloy Steel CS Zinc Plated Vinyl Ductile Iron Alloy Steel Stainless Steel
CS3
Alloy Steel CS Zinc Plated Vinyl Ductile Iron Alloy Steel Stainless Steel
S1
Alloy Steel CS Zinc Plated Vinyl Ductile Iron Alloy Steel Stainless Steel
S8
Stainless Steel Stainless Steel Vinyl Ductile Iron Alloy Steel Stainless Steel
2 inch (50 mm) Reduced Port and smaller. 2 inch (50 mm) Full Port and larger.
WKM
CT-WKM-210/310
10/06 NP-2M
13
DISTRIBUTED VALVES
SERIES 310
1/4 in. (8 mm) FULL PORT THROUGH 4 in. (100 mm) REDUCED PORT FLANGED, THREADED AND SOCKET WELD
B136/B138 Threaded B100/B110 Class150 Raised Face Flanges B170/B172 Class 600 Ring Joint Flanges B106/B103 Socket Weld
1 in. (25 mm) REDUCED PORT AND SMALLER
B120/B128 Class 300 Raised Face Flanges B102/B112 Class150 Raised Face Flanges
Q S
STEM DIMENSIONS
B114/B182 Class 600 Raised Face Flanges B122/B130 Class 300 Raised Face Flanges
1 in. (25 mm) FULL PORT THROUGH 2 in. (50 mm) REDUCED PORT
J J H G W F E D A X G B
BORE DIA
Q S
STEM DIMENSIONS
J J H G T
W E B D F E
BORE DIA
DIA
A
2 in. (50 mm) FULL PORT THROUGH 4 in. (100 mm) REDUCED PORT
DIA
B A
H
BORE DIA
J H X G
STEM DIMENSIONS
UNIBODY DESIGN
J J G X W T
STEM DIMENSIONS
F
E B D
BORE DIA
E B D
BORE DIA
DIA
A 150 Flg 300 Flg 150 Flg 300 Flg B102 B122 B112 B130
4.62 5.00 117 127 6.00 6.50 152 165 4.25 108 5.50 140 -
D
1.75 1.88 1.94 2.31 2.13 2.44 44 48 49 49 54 54
E
1.8 1.8 1.8 1.8 2.3 2.3 46 46 46 46 58 58
F
3.5 3.5 3.5 3.5 4.0 4.0 89 89 89 89 102 102
G
5.8 5.8 5.8 5.8 6.7 6.7 147 147 147 147 170 170
H*
10-24 .38 DP 10-24 .38 DP 10-24 .31 DP 10-24 .31 DP 10-24 .25 DP 10-24 .25 DP 10-24 9.7 DP 10-24 9.7 DP 10-24 7.9 DP 10-24 7.9 DP 10-24 6.4 DP 10-24 6.4 DP
J
1.0 1.0 1.0 1.0 1.0 1.0 25 25 25 25 25 25
Q*
7/16-20 7/16-20 7/16-20 7/16-20 7/16-20 7/16-20 7/16-20 7/16-20 7/16-20 7/16-20 7/16-20 7/16-20
S
0.246 0.246 0.246 0.246 0.246 0.246 6 6 6 6 6 6
T
0.41 0.41 0.41 0.41 0.48 0.48 10 10 10 10 12 12
W
0.72 0.72 0.72 0.72 0.84 0.84 18 18 18 18 21 21
X
0.38 0.38 0.38 0.38 0.38 0.38 10 10 10 10 10 10
SIZE mm
15 FP 20 RP 25 RP
14
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
SERIES 310 1/4 in. (8 mm) FULL PORT THROUGH 4 in. (100 mm) REDUCED PORT FLANGED, THREADED AND SOCKET WELD DIMENSIONS
B
0.38 0.38 0.38 0.50 0.75 0.75 1.00 1.50 2.00 3.44
C
-
G
4.3 4.3 4.3 5.7 5.7 5.4 7.0 9.5 9.5
H*
#8-32 .26 DP #8-32 .26 DP #8-32 .26 DP
Q*
S
0.18 0.18 0.18 0.26 0.26 0.26 0.36 0.45 0.45
X
0.38 0.38 0.38 0.38 0.38 0.38 0.38 0.38 0.38 0.38 0.38 0.38 0.38
1.4 2.8 1.4 2.8 1.4 2.8 1.8 3.5 1.9 3.5 1.9 3.5
0.25 0.55 0.25 0.55 0.25 0.55 0.34 0.72 0.34 0.72 0.34 0.72 0.63 1.25 0.81 1.50 0.81 1.50 1.37 1.88 1.37 1.88 1.75 2.31 1.75 2.31
#10-24 .26 DP 1.00 7/16-20 #10-24 .26 DP 1.00 7/16-20 #10-24 .26 DP 1.00 7/16-20 1/4-20 .39 DP 1.25 5/16-18 .45 DP 1.50 5/16-18 .45 DP 1.50 1/2-13 .50 DP 2.44 1/2-13 .50 DP 2.44 1/2-13 .50 DP 3.00 1/2-13 .50 DP 3.00 5/8-18 3/4-16 3/4-16 -
2.12 2.44 2.50 3.06 3.00 3.25 3.00 3.25 3.75 4.12 3.75 4.12 4.50 5.00
3.25 5.0 5.4 15.0 4.12 5.0 5.4 15.0 4.12 6.4 7.1 15.0 5.38 6.4 7.1 15.0
8.0 11.12 14.0 14.12 8.0 11.12 14.0 14.12 9.0 12.00 17.0 17.12
SIZE mm
6 FP 10 FP 15 RP 15 FP 20 FP 25 RP 25 FP 40 FP 50 RP 50 FP 80 FP 100 RP 76 83 95 102 108 114 114 133 159 159 254 260 127 165 178 178 203 203 229 165 190 216 216 283 283 305 216 241 292 292 356 356 432 216 241 295 295 359 359 435 10 10 10 13 19 19 25 38 38 51 51 87 87 13 25 51 76 102 18 18 18 20 27 27 34 46 46 60 60 83 83 54 64 76 76 95 95 114 62 78 83 83 105 105 127 62 78 83 83 35 35 35 45 48 48 70 70 70 89 89 89 108 108 108 145 145 137 #8-32 6.6 DP #8-32 6.6 DP #8-32 6.6 DP #10-24 6.6 DP #10-24 6.6 DP #10-24 6.6 DP 1/4-20 9.9 DP 22 22 22 25 25 25 32 5/16-24 5-16-24 5/16-24 7/16-20 7/16-20 7/16-20 5/8-18 3/4-16 3/4-16 28 28 28 28 5 5 5 7 7 7 9 11 11 18 18 19 19 6 6 6 9 9 9 16 21 21 35 35 44 44 14 14 14 18 18 18 31 38 38 48 48 59 59 10 10 10 10 10 10 10 10 10 10 10 10 10
71 107 178
94 127 241 5/16-18 11.4 DP 38 94 127 241 5/16-18 11.4 DP 38 127 137 381 1/2-13 12.7 DP 1/2-13 12.7 DP 1/2-13 12.7 DP 1/2-13 12.7 DP 62 62 76 76
80 x 50 RP 229
105 127 137 381 105 163 180 381 137 164 180 381
A
7.00 7.88 8.25 8.25 9.25 10.25
B
0.38 0.38 0.75 0.75 1.50 1.50
C
1.41 1.41 1.94 1.94 3.56 3.56
D
0.62 0.62 1.00 1.00 1.75 1.75
E
1.41 1.41 1.94 1.94 3.56 3.56
F
2.84 2.84 3.75 3.75 5.00 5.00
G
4.25 4.25 5.75 5.75 9.50 9.50
H
#8-32 .25 DP #8-32 .25 DP #10-24 .25 DP #10-24 .25 DP 5/16-18 .44 DP 5/16-18 .44 DP
J
0.88 0.88 1.00 1.00 1.50 1.50
Q*
5/16-24 5/16-24 7/16-20 7/16-20 3/4-16 3/4-16
S
0.18 0.18 0.26 0.26 0.45 0.45
T
0.25 0.25 0.34 0.34 0.81 0.81
W
0.56 0.56 0.75 1.14 1.34 1.34
X
0.38 0.38 0.38 0.38 0.38 0.38
SIZE mm
8 FP 15 RP 20 FP 25 RP 40 FP 50 RP B103 B106 B103 B106 B103 B106 177.80 200.15 209.55 209.55 234.95 260.35 9.65 9.65 19.05 19.05 38.10 38.10 35.81 35.81 49.28 49.28 90.42 90.42 15.75 15.75 25.40 25.40 44.45 44.45 35.81 35.81 49.28 49.28 90.42 90.42 72.14 72.14 95.25 95.25 127.00 127.00 107.95 107.95 146.05 146.05 241.30 241.30 #8-32 6.4 DP #8-32 6.4 DP #10-24 6.4 DP #10-24 6.4 DP 5/16-18 11.2 DP 5/16-18 11.2 DP 22.35 22.35 25.40 25.40 38.10 38.10 5/16-24 5/16-24 7/16-20 7/16-20 3/4-16 3/4-16 4.57 4.57 6.60 6.60 11.43 11.43 6.35 6.35 8.64 8.64 20.57 20.57 14.22 14.22 19.05 28.96 34.04 34.04 9.65 9.65 9.65 9.65 9.65 9.65
WKM
CT-WKM-210/310
10/06 NP-2M
15
DISTRIBUTED VALVES
Deep seat pockets protects seats from the flow to extend service life. Body Drain Fitting.
(Not shown)
ASME/ANSI CLASS 600 4 in. (100 mm) FULL PORT THROUGH 8 in. x 6 in. (200 mm x 150 mm) REDUCED PORT NACE MR0175 (Rev. 2002). GEAR OPERATORS REQUIRED FOR ALL SIZES.
16
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
SERIES 310
W-K-M DynaSeal 310 floating ball valves satisfy a wide range of applications. Available in a variety of standard and optional materials, they may be specified in sizes from 4 in. (100 mm) to 14 in. (350 mm) and ASME/ANSI Class 150 and 300. ASME/ANSI Class 600 is available in sizes 4 in. (100 mm) through 8 in. x 6 in. (200 mm x 150 mm). Engineered for heavy duty, maintenance free performance, the DynaSeal 310 is commonly selected for a variety of applications in virtually any industry. CHEMICAL & PETROCHEMICAL PLANTS The list of chemical and petrochemical applications for DynaSeal ball valves is limitless. They are serving in many plastic plants handling such slurries as 40% vinyl chloride, in high pressure catalyst lines and in processes handling dry lading such as polyethylene and polystyrene powders. There are hundreds of applications in such plants where DynaSeals are providing efficient service. REFINING DynaSeal is the workhorse of the refining industry. The many metal seats, seals and available trims offer the versatility needed to handle the wide variety of products used in the refining process. HIGH TEMPERATURE SERVICE Special high temperature trims are available for DynaSeal 310 ball valves which provide for service to 600F (316C). This trim is excellent for steam service, hot oil, heat transfer fluids, boiler feed-water and similar applications. LOW TEMPERATURE SERVICE Standard trims accomodate temperatures to -20F (-29C). For temperatures to -50F (-46C); please consult factory. MAINTENANCE FREE PERFORMANCE Under most conditions, the DynaSeal 310 floating ball valve will provide years of trouble free service with no maintenance required. In some severe applications, such as handling extremely abrasive slurries at high temperature, it may be necessary to replace the seats occasionally. Seat and seal kits are available and replacement can be done easily with ordinary tools. SOUR OIL AND GAS SERVICE DynaSeal ball valves have served for years in gathering lines, manifolds and field processing units in sour oil and gas fields. They can be trimmed to conform with NACE MR0175 (Rev. 2002).
TEFLON BODY SEAL A Teflon body seal is used between the valve body and tailpiece. DEEP RECESSED SEATS The seat is recessed into a deep machined pocket, which serves to surround and protect the seat on all sides. This design eliminates cold flow into the valve conduit where it can be damaged by the action of the ball or the flow medium.The result is extremely long service life. ADJUSTABLE, REPLACEABLE PACKING The inline valve stem packing through ASME/ANSI Class 300 consists of PTFE impregnated graphite with an impervious metal barrier. The packing is field adjustable and never requires lubrication. The packing and the stainless steel cap can be replaced without removing the valve from line. FUGITIVE EMISSIONS DynaSeal 310 ball valves through ASME/ANSI Class 300 can be supplied and certified to meet the requirements of fugitive emissions as regulated by The 1990 Amendment to The Clean Air Act. POSITIVELY RETAINED STEM The stem is positively retained and cannot be removed with the valve in service. INDICATOR HANDLE The design of the handle ASME/ANSI Class 300 permits installation on the stem in the correct position only, in alignment with the ball port. When the handle is aligned with the pipe, the valve is open. When the handle is perpendicular to the pipe, the valve is closed. FLOATING BALL DESIGN DELIVERS TIGHT SEAL The ground and polished ball is free to float and mates perfectly with the conical seats for a positive, leakproof seal. Self cleaning and self adjusting, the ball is also pressure activated. The higher the line pressure, the tighter the seal. GEAR MOUNTING BRACKETS FOR:
4 in. FP - 8 in. RP (100 mm FP - 200 mm RP) Class 150/300 8 in. FP & 10 in. RP (200 mm FP & 250 mm RP) Class 150 8 in. FP & 10 in. RP (200 mm FP & 250 mm RP) Class 300 10 in. FP - 14 in. RP (250 mm FP - 350 mm RP) Class 150/300
WKM
CT-WKM-210/310
10/06 NP-2M
17
DISTRIBUTED VALVES
SERIES 310
ASME/ANSI CLASS 150, 300 AND 300 BUTT WELD
Key Stop Plate Cap Screw Bonnet Cap Compression Ring Stem Packing Body Stem Retainer Pin Pipe Plug Stem Stem Gasket Ball Body Stud Ground Spring Drain Fitting Seat Rings Body Stud Nut
STANDARD MATERIALS
Tailpiece
Body: Carbon Steel and Stainless Steel Ball/Stem: Carbon Steel, Stainless Steel & Monel
INDUSTRY COMPLIANCE
ASME/ANSI B16.5, B16.34 MSS-SP-25, 55, 72 API 607 4th Edition (Fire Test Specifications)
Handwheel Stud Washer Nut Stem O-Ring Stem Gasket Key Stem Ball Body Stud Body Stud Nut Ground Spring Drain Fitting Seat Rings
SIZE
(mm)
(100) FP
150
Body
14 x 12 (350 x 300) RP
18
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
CS
A216 Gr. WCC A193 Gr. B7 A194 Gr. 2H Carbon Steel ASTM A105/A216 Gr. WCC A193 Gr. B7 A194 Gr. 2H Alloy Steel A216 Gr. WCC Plated
CS2*
A216 Gr. WCC A193 Gr. B7 A194 Gr. 2H Stainless Steel ASTM A105/A216 Gr. WCC A193 Gr. B7 A194 Gr. 2H Alloy Steel A216 Gr. WCC Plated
S1
A351 Gr. CF8M A193 Gr. B7 Plated A194 Gr. 2H Plated Stainless Steel A351 Gr. CF8M A193 Gr. B7 Plated A194 Gr. 2H Plated Alloy Steel Plated A216 Gr. WCC Plated
S8*
A351 Gr. CF8M A193 Gr. B8 A193 Gr. B8 Stainless Steel A351 CF8M A193 Gr. B8 A194 Gr. B8 Stainless Steel A351 Gr. CF8M
* CS2 and S8 to be used for H2S service. Only use with S1 internal trim. Meets NACE MR0175 (Rev. 2002). Standard trim for ASME/ANSI Class 600. ** 8 in. (200 mm) through 14 in. x 12 in. (350 mm x 300 mm) ASME/ANSI Class 150 and 300. Only available in A216 Gr. WCC material. *** Use only for 4 in. (100 mm) through 8 in. x 6 in. (200 mm x 150 mm) ASME/ANSI Class 150 and 300.
01
TFE TFE TFE
42
Filled TFE TFE Filled TFE
43*
FKM O-Ring Nylon Washer FKM O-Ring**
18
Special Filled TFE Filled TFE Filled TFE
28
Filled TFE Filled TFE Filled TFE
60
Solid Stellite Graphite Filled TFE Filled TFE
92H
316 SS Chromium Carbide Coat Filled TFE Filled TFE Filled TFE
* Specify Code 43 as standard trim for ASME/ANSI Class 600. Seal set consists of: Acetal Plastic Seats, High Fluorine FKM O-Ring for Tailpiece & stem. ** Class 600 Valves have FKM O-Ring stem seal.
CS
AISTM A105 Hard Chrome Plate 304 SS Carbon Steel ENP 304 SS Carbon Steel Carbon Steel
S1
316 SS 304 SS 316 SS 304 SS 316 SS 316 SS
S2*
316 SS 304 SS 17-4 SS 304 SS 316 SS 316 SS
ML
B164 Class B Ni-Cu Alloy 304 SS B164 Class B Ni-Cu Alloy 304 SS 316 SS 316 SS
ACTUATOR CODES*
PART (Body) For All Body - Tailpiece Trim Codes
Ductile Iron Carbon Steel Carbon Steel Alloy Steel Carbon Steel Carbon Steel As Selected Carbon Steel
ACTUATOR CODES**
PART (Body)
Mounting Bracket Bolting Set Screw Stem Adapter Actuator Handwheel
Mounting Bracket Adapter Plate Stem Adapter Bolting Key Set Screw Actuator Handwheel
*
** 4 in. through 8 in. (100 mm through 200 mm) ASME/ANSI Class 600.
*** 4 in. through 8 in. x 6 in. (100 mm through 200 mm x 150 mm) ASME/ANSI Class 150 and 300.
10 in. through 14 in. x 12 in. (250 mm through 350 mm x 300 mm) ASME/ANSI Class 150 and 300.
WKM
CT-WKM-210/310
10/06 NP-2M
19
DISTRIBUTED VALVES
SERIES 310
X
4 in (100 mm) FULL PORT THROUGH 14 in. (350 mm) REDUCED PORT ASME/ANSI CLASS 150, 300, 600 AND BUTT WELD 300
Z Y G
DIA THREAD SIZE
AA THREAD DEPTH
= KEY SIZE
E B D
BORE DIA
P H
DIA
M A
VALVE WITH WRENCH (LEVER) 4 in. (100 mm) THROUGH 14 in. x 12 in. (350 mm x 300 mm) Class 150/300
A
VALVE WITH GEAR 4 in. (100 mm) THROUGH 8 in. x 6 in. (200 mm x 150 mm) CLASS 600
K
DIA
P G
U W
THROUGH HOLE DIA
U W
S S
E B D A
VALVE WITH WRENCH (LEVER) 4 in. x 14 in. x 12 in. (100 mm x 350 mm x 300 mm) Class 150/300
BORE DIA
H B
BORE DIA
D A
VALVE WITH GEAR 4 in. x 14 in. x 12 in. (100 mm x 350 mm x 300 mm Class 150/300
V
MOUNTING BRACKET 4 in. FP - 8 in. RP (100 mm FP - 200 mm RP) Class 150/300 8 in. FP & 10 in. RP (200 mm FP & 250 mm RP) Class 150
MOUNTING BRACKET 8 in. FP & 10 in. RP (200 mm FP & 250 mm) RP Class 300 10 in. FP - 14 in. RP (250 mm FP - 350 mm RP) Class 150/300
B
4.00 6.00 102 152
C
4.00 6.00 102 152
D
6.52 8.17 166 208
H
6.81 9.28 173 236
K
20.00 24.00 508 610
L
2.50 4.84 64 123
M
9.72 14.26 247 362
P
9.79 13.43 249 341
R
8.18 11.25 208 286
SIZE mm
100 150
A
22.00 26.00 559 660
B
4.00 6.00 102 152
C
6.00 8.00 152 203
D
6.52 8.17 166 208
H
6.81 9.28 173 236
K
20.00 24.00 508 610
L
2.50 4.84 64 123
M
9.72 14.26 247 362
P
9.79 13.43 249 341
R
8.18 11.25 208 286
SIZE mm
150 x 100 200 x 150
20
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
SERIES 310 4 in. (100 mm) FULL PORT THROUGH 14 in. (350 mm) REDUCED PORT
R 9.15 9.15
S -
T -
AA
0.56 2.44 4.921 1.88 4.63 3/8-16NC 0.63 0.56 2.44 4.921 1.88 4.63 3/8-16NC 0.63 0.56 2.44 4.921 1.88 4.63 3/8-16NC 0.63 0.56 2.44 4.921 1.88 4.63 3/8-16NC 0.63 0.68 4.00 5.512 3.50 8.25 0.75 3.00 3.50 8.25 3.50 8.25 3.50 8.25 3.50 8.25 3.50 8.25 3.50 8.25 1-8NC 1-8NC 1-8NC 1-8NC 1-8NC 1-8NC 1-8NC 1.13 1.13 1.13 1.13 1.13 1.13 1.13
N/A -
6.0 8.20 11.38 12.63 48.0 9.44 1.500 14.0 6.0 8.20 11.38 12.63 48.0 9.44 1.500 14.0 8.0 9.95 16.38 8.0 9.97 16.38 13.50 2.375 16.0 12.50 2.375 20.0 15.12 2.938 20.0 15.12 2.938 20.0 15.12 2.938 16.0 16.38 2.938 20.0 16.38 2.938 24.0
2.80 10.95 0.375 12.72 11.03 4.11 13.24 0.375 13.28 11.33 4.11 11.11 0.625 17.34 15.39 5.12 15.25 0.625 17.07 14.67
10.0 10.0 11.63 18.50 10.0 10.0 11.65 18.50 12.0 12.0 13.97 20.13
5.12 15.25 0.750 19.70 17.30 7.75 5.75 0.75 3.00 8.31 17.61 0.750 21.24 17.30 7.75 5.75 0.75 3.00 8.31 15.32 0.750 21.24 17.30 7.75 5.75 0.75 3.00 8.31 17.61 0.750 22.49 18.55 7.75 5.75 0.75 3.00 8.31 17.61 0.750 22.49 18.55 7.75 5.75 0.75 3.00
10
12
mm
300 SIZE LONG SHORT LONG SHORT BW in. B110 B113 B128 B134 B150 100 150 200 229 394 457 533 250 300 610 N/A N/A N/A 267 N/A 305 403 502 568 648 N/A 305 403 419 559 635 A* Class 150 RF 300 RF B 102 102 152 152 203 203 254 254 254 305 305 C 102 102 152 152 203 203 254 254 254 305 305 D 164 164 208 208 253 253 295 295 296 355 355 E 219 219 289 289 416 416 470 467 470 511 511 F 251 251 G H J K L 71 71 71 M 200 206 278 N 6.35 6.35 9.53 9.53 15.88 15.88 19.05 22.75 19.05 19.05 19.05 P 275 275 323 337 440 434 500 535 539 571 571 R 232 232 280 280 391 373 439 439 439 471 471 S 197 197 197 197 197 T 146 146 146 146 146 U 14 14 14 14 17 19 19 19 19 19 19 V W X Y Z AA
31.75 203 31.75 254 38.10 356 38.10 356 60.33 406 60.33 508 74.63 508 77.45 504 74.63 406 74.63 508 74.63 610
118 3/8-16NC 16 118 3/8-16NC 16 118 3/8-16NC 16 118 3/8-16NC 16 210 210 210 210 210 210 210 1-8NC 1-8NC 1-8NC 1-8NC 1-8NC 1-8NC 1-8NC 29 29 29 29 29 29 29
321 1219 240 321 1219 240 343 318 384 382 384 416 416
104 336 104 282 130 387 130 387 212 444 211 389 211 447 211 447
A* Class 300 RF
LONG SHORT
AA
SHORT
B122 N/A 4.00 4.00 6.00 6.00 6.00 8.00 8.00 6.45 6.45 8.63 8.63 9.88 36.00 7.56 1.250 8.00 2.80 7.88 0.250 10.84 9.15 9.88 36.00 7.56 1.250 10.00 2.80 8.12 0.250 10.84 9.15 0.56 2.44 4.921 1.88 4.63 3/8-16NC 0.63 0.56 2.44 4.921 1.88 4.63 3/8-16NC 0.63 0.56 2.44 4.921 1.88 4.63 3/8-16NC 0.63 0.56 2.44 4.921 1.88 4.63 3/8-16NC 0.63 0.68 4.00 5.512 3.50 8.25 0.75 3.00 3.50 8.25 3.50 8.25 3.50 8.25 3.50 8.25 3.50 8.25 1-8NC 1-8NC 1-8NC 1-8NC 1-8NC 1-8NC 1.13 1.13 1.13 1.13 1.13 1.13
8.20 11.38 12.63 48.00 9.44 1.500 14.00 2.80 10.95 0.375 12.72 11.03 8.20 11.38 12.63 48.00 9.44 1.500 16.00 4.11 11.11 0.375 13.28 11.33 13.50 2.375 20.00 4.11 13.64 0.625 17.34 15.39 12.50 2.375 20.00 5.12 15.25 0.625 17.07 14.67
8.00 10.00 10.10 16.38 8.00 10.00 10.10 16.38 10.00 12.00 11.78 18.50 10.00 12.00 11.78 18.50 12.00 14.00 13.97 20.13 12.00 14.00 13.97 20.13
N/A
N/A
15.12 2.938 24.00 5.12 15.25 0.750 19.70 17.30 7.75 5.75 0.75 3.00 15.12 2.938 20.00 8.31 17.61 0.750 21.24 17.30 7.75 5.75 0.75 3.00 16.38 2.938 20.00 8.31 17.61 0.750 22.49 18.55 7.75 5.75 0.75 3.00 16.38 2.938 24.00 8.31 17.61 0.750 22.49 18.55 7.75 5.75 0.75 3.00
14 x 12 27.00
N/A
N/A
mm
SIZE mm 150 RF
LONG
A* Class 300 RF
LONG SHORT
AA
SHORT
B122 N/A 419 N/A 102 152 102 152 152 203 152 203 203 254 203 254 254 305 254 305 305 356 305 356 164 164 208 208 257 257 299 299 355 355 219 219 289 289 416 416 470 470 511 511 251 251 914 914 192 192 240 240 343 318 384 384 416 416 31.75 31.75 38.10 38.10 60.33 60.33 74.63 74.63 74.63 74.63 203 254 356 406 508 508 610 508 508 610 71 71 71 104 104 130 130 211 211 211 200 206 278 282 6.35 6.35 9.53 9.53 275 275 323 337 232 232 280 288 391 373 14 14 14 14 62 124.99 62 124.99 62 124.99 62 124.99 48 48 48 48 89 89 89 89 89 89 118 118 118 118 210 210 210 210 210 210 3/8-16NC 16 3/8-16NC 16 3/8-16NC 16 3/8-16NC 16 1-8NC 1-8NC 1-8NC 1-8NC 1-8NC 1-8NC 29 29 29 29 29 29
150 x 100 200 x 150 250 x 200 300 x 250 350 x 300
346 15.88 440 387 15.88 434 387 19.05 500 447 19.05 539 447 19.05 571 447 19.05 571
17 102 140.00 19 19 19 19 19 76 76 76 76 76 -
N/A
N/A
439 197 146 439 197 146 471 197 146 471 197 146
N/A
N/A
* Centerline-to-face dimension is half of dimension A, except: 4 in. (100 mm) ASME/ANSI Class 150 Full Port - stem is offset 1/2 in. (12.7 mm) towards body end and 6 in. (150 mm) ASME/ANSI Class 150 Full Port Long Pattern - stem is offset 2 1/2 in. (63.5 mm) towards body end.
WKM
CT-WKM-210/310
10/06 NP-2M
21
DISTRIBUTED VALVES
SEAL CODE 01
Temp F 200 250 300 350 400 Temp C 93 121 149 177 204 Valve Port Size in. (mm) 1/4 - 3/4 1 - 1 1/2 2 3-4 6 - 12 (80 - 20) (25 - 40) (50) (80 - 100) (150 - 300) 1500 1500 1400 1100 600 100 1000 1000 900 650 375 100 750 750 700 500 300 100 600 600 550 425 250 100 285 285 150 50 -
SEAL CODE 42
Temp F 200 250 300 350 400 450 500 Temp C 93 121 149 177 204 232 260 Valve Port Size in. (mm) 1/4 - 1 1/2 2 3 (8 - 40) (50) (80) 1500 1400 1250 1090 930 770 610 450 1500 1325 1150 975 800 640 475 300 740 740 740 740 590 450 325 200
SEAL CODE 18
Temp F 200 250 300 350 400 450 500 550 Temp C 93 121 149 177 204 232 260 288 316 329 Valve Port Size in. (mm) 1/4 - 1 1/2 2 3 4 - 12 (8 - 40) (50) (80) (100 - 300) * * 1775 1650 1575 1500 1300 1075 850 350 100 * * 1250 1175 1075 1000 875 725 600 100 0 * * * 740 700 650 600 550 500 75 0 * * * 600 500 400 300 200 100 0 0
600 625
* On Application.
SEAL CODE 23
Temp F Temp C 93 107 Valve Port Size in. (mm) 1/4 - 3/8 1/2 - 3/4 (8 - 10) (15 - 20) 5000 3250 2500 3750 2000 1500
22
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
THREADED VALVES
Body trim code S8 and CS3 are suitable for service to -50F (-46C). All other trims are limited to operating temperatures no lower than -20F (-29C) These pressure/temperature ratings are in conformance with ASME/ANSI B16.5, B16.34.
WKM
CT-WKM-210/310
10/06 NP-2M
23
DISTRIBUTED VALVES
END CONNECTION
Threaded Threaded Threaded 150 (20 PN) Flanged (Unibody) 300 (50 PN) Flanged (Unibody) Threaded 150 (20 PN) Flanged (Unibody) 300 (50 PN) Flanged (Unibody) Threaded 150 (20 PN) Flanged 300 (50 PN) Flanged 300 (50 PN) Flanged (Unibody) 600 (100 PN) Flanged Theaded 150 (20 PN) Flanged 300 (50 PN) Flanged 600 (100 PN) Flanged Threaded 150 (20 PN) Flanged 300 (50 PN) Flanged 600 (100 PN) Flanged Threaded 150 (20 PN) Flanged 300 (50 PN) Flanged 600 (100 PN) Flanged Threaded 150 (20 PN) Flanged 300 (50 PN) Flanged 600 (100 PN) Flanged
1 1/2
(40)
(50)
(80)
(100)
END CONNECTION
150 (L) Flanged 300 (L) Flanged Butt Weld 600 Flanged 150 (L) Flanged 150 (S) Flanged 300 (L) Flanged Butt Weld 150 (L) Flanged 150 (S) Flanged 300 (L) Flanged Butt Weld 600 Flanged 150 (L) Flanged 150 (S) Flanged 300 (S) Flanged Butt Weld 150 (L) Flanged 150 (S) Flanged 300 (L) Flanged 300 (L) Flanged Butt Weld 600 Flanged 150 (L) Flanged 150 (L) Flanged 300 (L) Flanged 300 (L) Flanged Butt Weld 150 (L) Flanged 150 (L) Flanged 300 (L) Flanged 300 (L) Flanged Butt Weld 150 (L) Flanged 300 (L) Flanged Butt Weld (L) Long Pattern.
(150)
(150) WGA
(200)
10
(250) WGA WGA WGA (300) WGA WGA WGA (350) WGA
12
14
24
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
MOP
3000 5000 3000 3750 3000 3750 3000 3000 3000 3000 3000 3000
MALE x FEMALE THREADED ENDS FULL PORT WEIGHTS REDUCED PORT WEIGHTS lb. kg lb. kg
6 6 2 6 19 2.72 2.72 3 3 7 7 1.36 1.36 3.18 3.18 1.36 2.72 9.53
150
16 10 35 88 223 102 464 117 1228 359 2118 390 5403 1215 11261 2671 17037 4881 26163 10580
600
68 184 99 362 133 928 406 -
* Flow of water in U.S. Gallons per minute per 1 psi pressure drop across a fully open valve. (S) Short Pattern. (L) Long Pattern.
WKM
CT-WKM-210/310
10/06 NP-2M
25
DISTRIBUTED VALVES
Multiply Trim 42 Torque x 2 for Seat Seal Codes 60, 60A, 92H.
500
48 60 95 245 410 960 1635
740
48 64 105 260 450 1075 1885
2250
70 140 260 455 1050 2000 -
2500
85 165 295 520 1200 2200 -
3000
100 215 370 700 1550 2600 -
1042 1240
26
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
500
60 70 108
740
60 70 125
1000
60 82 140
3000
100 220 560
3500
115 276 695
3750
125 310 800
4000
130 -
4500
150 -
5000
165 -
DIFFERENTIAL PRESSURE (psi) VALVE BORE SIZE in. (mm) 0-285 500 740
4 6 8 10 12 (100) (150) (200) (250) (300) 2400 5400 10000 16000 32000 3300 8200 15000 23000 39000 4200 11200 20300 30500 46500
** Multiply Trim 42 Torque x 2 for Seat Seal Codes 60, 60A, 92H.
Note: The torque values listed for 285 psi and greater are based on valves controlling the flow of clean lubricating liquid at ambient temperature. For valves at pressure less that 285 psi use the value for 285 psi. Interpolation may be used for any pressure above 285 psi but less than maximum pressure listed. Running torque values will average two-thirds of these values. For running torque values less than breakaway torque values at 285 psi use breakaway torque values. Reseating torque is equal to breakaway torque. For operating temperatures between -20F to -50F (-29C to -46C) multiply these values by 1.20. These torque values do not contain service or safety factors. Actuator selection should be made based on experience and appropriate service and safety factors.
WKM
CT-WKM-210/310
10/06 NP-2M
27
DISTRIBUTED VALVES
Rating interpretation:
A - excellent; B - good (slightly attacked); C - fair (moderately attacked, robably unsuitable); D - not recommended.
SPL 07 D D B D D D D D A C B A C D A A A B D D D B B A B D B C A A A D C B A A A A A A A A A A A A
STD 43 B B D D D D D B D C B C B C D B C C B C D D D D D B C D B C C C A B C C D A A B B A A A A A A A
STD INT CS C A C D D C D A A A B B B B B C C A A D A A B C B D C C D D D D C C A C D D D A A B C C B C C C
STD INT S1 A A A A B A B A A A A A A A A A A A A A A A A B B C B B B A B B B B B A D B B A A B C B B B A A
SPL INT S2 C A C D D C D A A A B B B B B C C A A A A A B C B D C C D D D D C C A C D D D A A B C C B C C
SPL INT ML A A A A A A A A A A A A A A A A A A A A B B B B B B D D C D C C C B B A B A D A A B B B A B A A
ACETALDEHYDE ACETATE SOLVENTS ACETIC ACID (30%) ACETIC ACID (AERATED) ACETIC ACID (AIR FREE) ACETIC ACID (CRUDE) ACETIC ANHYDRIDE ACETONE ACETYLENE (DRY ONLY) ACRYLONITRILE ALCOHOL-AMYL ALCOHOL-BUTYL ALCOHOL-ETHYL ALCOHOL-METHYL (METHANOL) ALUMINUM CHLORIDE (DRY) ALUMINUM SULFATE (ALUMS) ALUM'S AMINES AMINES BASED-CORROSION INHIBITOR AMINES RICH AMMONIA (AQUEOUS) AMMONIA ANHYDROUS AMMONIA SOLUTIONS AMMONIUM BICARBONATE AMMONIUM CARBONATE AMMONIUM CHLORIDE AMMONIUM HYDROXIDE (28%) AMMONIUM HYDROXIDE CONCENTRATED AMMONIUM MONOPHOSPHATE AMMONIUM NITRATE AMMONIUM PHOSPHATE (DIBASIC) AMMONIUM PHOSPHATE (TRIBASIC) AMMONIUM SULFATE AMYL ACETATE ANILINE ANILINE DYES ANTIMONY TRICHLORIDE APPLE JUICE ARSENIC ACID ASPHALT EMULSION ASPHALT LIQUID BARIUM CARBONATE BARIUM CHLORIDE BARIUM HYDROXIDE BARIUM SULFATE BARIUM SULFIDE BEER (ALCOHOL INDUSTRY) BEER (BEVERAGE INDUSTRY)
28
WKM
CT-WKM-210/310
10/06 NP-2M
(-) - Not tested. VTFEP - Virgin TFE Packing. Note: All ladings at ambient temperatures except as noted.
DISTRIBUTED VALVES
(-) - Not tested. VTFEP - Virgin TFE Packing. Note: All ladings at ambient temperatures except as noted.
WKM
CT-WKM-210/310
10/06 NP-2M
29
DISTRIBUTED VALVES
DRILLING MUD DRIP COCKS, GAS DRY CLEANING FLUIDS EPSOM SALT ETHANE ETHANOLAMINE ETHERS ETHYL ACETATE ETHYL ACRYLATE ETHYL CHLORIDE (DRY) ETHYL CHLORIDE (WET) ETHYLENE (LIQUID OR GAS) ETHYLENE GLYCOL ETHYLENE OXIDE FATTY ACIDS FERRIC CHLORIDE FERRIC NITRATE FERRIC SULFATE FERROUS CHLORIDE FERROUS SULFATE FERROUS SULFATE (SAT) FERTILIZER SOLUTIONS FISH OILS FLUORINE (DRY) FLUOROSILICIC ACID FOOD FLUIDS - PASTES FORMALDEHYDE (COLD) FORMALDEHYDE (HOT) FORMIC ACID (COLD) FORMIC ACID (HOT) FREON 12 (DRY) FRUIT JUICES FUEL JET JP-4 FUEL JET JP-5 100F FUEL JET JP-6 100F FUEL OIL FUEL RP-1 FURFURAL GALLIC ACID GAS (MANUFACTURED) GAS ODORIZERS (VTFEP) GAS, NATURAL GASOLINE, AVIATION GASOLINE, SOUR GASOLINE, LEADED, LOW OCTANE GASOLINE, UNLEADED, LOW OCTANE GELATIN GLUCOSE GLUE GLYCERINE - GLYCEROL GLYCOLS GREASE HEPTANE HEXANE HEXANOL, TERTIARY HYDRAULIC OIL PHOSPHATE ESTER HYDRAULIC OIL PETROLEUM BASE HYDROBROMIC ACID HYDROCHLORIC ACID 37% AIR FREE HYDROCYANIC ACID HYDROFLUORIC ACID HYDROFLUOSILICIC ACID
30
WKM
CT-WKM-210/310
10/06 NP-2M
(-) - Not tested. VTFEP - Virgin TFE Packing. Note: All ladings at ambient temperatures except as noted.
DISTRIBUTED VALVES
HYDROGEN GAS (COLD) HYDROGEN PEROXIDE 30% (DILUTE) HYDROGEN PEROXIDE 90% HYDROGEN SULFIDE (DRY) HYDROGEN SULFIDE (WET) HYPO (SODIUM THIOSULFATE) HYPOCHLORITES, SODIUM ILLUMINATING GAS INK IODINE (WET) ISO-OCTANE ISODOFORM (DRY) SOPROPYL ALCOHOL ISOPROPYL ETHER KEROSENE KETCHUP KETONES LACQUERS (SOLVENTS) LACTIC ACID (CONC. COLD) LACTIC ACID (CONC. HOT) LACTIC ACID (DILUTE COLD) LACTIC ACID (DILUTE HOT) LARD OIL LEAD ACETATE LINOLEIC ACID LINSEED OIL LIQUEFIED PET GAS (LPG) LITHIUM BROMIDE LUBRICATING OIL MAGNESIUM BISULFATE (10%) MAGNESIUM CHLORIDE MAGNESIUM HYDROXIDE MAGNESIUM HYDROXIDE (HOT) MAGNESIUM SULFATE MALEIC ACID MALEIC ANHYDRIDE MALIC ACID MAYONNAISE MERCAPATANS MERCURIC CHLORIDE MERCURIC CYANIDE (10%) MERCURY METHANE METHYL ACETATE METHYL ACETONE METHYL CELLOSOLVE METHYL CHLORIDE (DRY) METHYL ETHYL KETONE METHYL FORMATE METHYLAMINE METHYLENE CHLORIDE (DRY) MILK MINE WATERS (ACID) MINERAL SPRITS MINERAL OIL MIXED ACIDS (COLD) MOLASSES - CRUDE MOLASSES, EDIBLE MTBE 100% MAX MTBE 40% MAX MURIATIC ACID MUSTARD
(-) - Not tested. VTFEP - Virgin TFE Packing. Note: All ladings at ambient temperatures except as noted.
WKM
CT-WKM-210/310
10/06 NP-2M
31
DISTRIBUTED VALVES
NAPHTHA NAPHTHALENE NICKEL AMMONIUM SULFATE (20%) NICKEL CHLORIDE NICKEL NITRATE (30%) NICKEL SULFATE NICOTINIC ACID NITRIC ACID (10%) (VTFEP) NITRIC ACID (100%) (VTFEP) NITRIC ACID (30%) (VTFEP) NITRIC ACID (80%) (VTFEP) NITRIC ACID ANHYDROUS/AQUEOUS (VTFEP) NITROBENZENE NITROGEN NITROUS ACID (10%) NITROUS GASES NITROUS OXIDE OIL, COTTONSEED OIL, PETROLEUM (REFINED) OIL, PETROLEUM (SOUR) H2S & CO2 OIL, WATER MIXTURES OIL, ANIMAL OIL, FISH OIL, FUEL OIL, LUBE OIL, MINERAL OLEIC ACID OLEUM OLIVE OIL OXALIC ACID OXYGEN OZONE (DRY) OZONE (WET) PAINTS AND THINNERS PALM OIL PALMITIC ACID PARAFFIN PARAFORMALDEHYDE PENTANE PERCHLOROETHYLENE PETROLATUM PHENOL (CARBOLIC ACID) PHENOL RESIN PHOSGENE (DRY) (VTFEP) PHOSGENE (WET) (VTFEP) PHOSPHORIC ACID (10%) COLD PHOSPHORIC ACID (10%) HOT PHOSPHORIC ACID (50%) COLD PHOSPHORIC ACID (50%) HOT PHOSPHORIC ACID (85%) COLD PHOSPHORIC ACID (85%) HOT PHTHALIC ACID PHTHALIC ANHYDRIDE PICRIC ACID PINE OIL PINEAPPLE JUICE POLY ESTER RESIN (VTFEP) POLYETHYLENE FLUFF POLYETHYLENE LIQUID POLYURETHANE POTASSIUM BISULFITE (10%) POTASSIUM BROMIDE
32
WKM
CT-WKM-210/310
10/06 NP-2M
(-) - Not tested. VTFEP - Virgin TFE Packing. Note: All ladings at ambient temperatures except as noted.
DISTRIBUTED VALVES
POTASSIUM CARBONATE POTASSIUM CHLORATE POTASSIUM CHLORIDE POTASSIUM CYANIDE POTASSIUM DICHROMATE POTASSIUM DIPHOSPHATE POTASSIUM FERRICYANIDE POTASSIUM FERROCYANIDE POTASSIUM HYDROXIDE 70% (COLD) POTASSIUM HYDROXIDE 70% (HOT) POTASSIUM HYDROXIDE-DILUTE (COLD) POTASSIUM HYDROXIDE-DILUTE (HOT) POTASSIUM IODIDE POTASSIUM NITRATE POTASSIUM PERMAGANATE POTASSIUM SULFATE POTASSIUM SULFIDE (10%) POTASSIUM SULFITE (10%) PRODUCER GAS PROPANE PROPLENE PROPYL ALCOHOL PROPYLENE GYLCOL PYROGALLIC ACID QUENCH OIL (WATER SOLUBLE) RESINS-ROSINS ROAD TAR ROOF PITCH RUBBER LATEX EMULSIONS RUBBER SOLVENT SALAD OIL SALICYLIC ACID SALT SEA WATER SHELLAC (BLEACHED) SHELLAC (ORANGE) SILICONE OILS SILVER NITRATE SOAP SOLUTIONS (STEARATES) SODIUM ACETATE SODIUM ALUMINATE SODIUM BICARBONATE SODIUM BISULFATE (10%) SODIUM BISULFITE (10%) SODIUM BORATE SODIUM BROMIDE (10%) SODIUM CARBONATE SODIUM CHLORATE SODIUM CHLORIDE SODIUM CHROMATE SODIUM CYANIDE (10%) SODIUM FLUORIDE SODIUM HYDROXIDE 20% (COLD) SODIUM HYDROXIDE 20% (HOT) SODIUM HYDROXIDE 50% (COLD) SODIUM HYDROXIDE 50% (HOT) SODIUM HYDROXIDE 70% (COLD) SODIUM HYDROXIDE 70% (HOT) SODIUM HYPOCHLORIDE SODIUM METAPHOSPHATE SODIUM METASILICATE (HOT) SODIUM METASILICATE (COLD)
(-) - Not tested. VTFEP - Virgin TFE Packing. Note: All ladings at ambient temperatures except as noted.
WKM
CT-WKM-210/310
10/06 NP-2M
33
DISTRIBUTED VALVES
SODIUM NITRATE SODIUM PERBORATE SODIUM PEROXIDE SODIUM PHOSPHATE (DIBASIC) SODIUM PHOSPHATE (TRIBASIC) SODIUM SILICATE SODIUM SILICATE (HOT) SODIUM SULFATE NA2S04 SODIUM SULFIDE (HOT) SODIUM SULFIDE NA2S02 SODIUM THIOSULFATE SOUR GAS AND OIL SOYBEAN OIL STANNIC CHLORIDE STANNOUS CHLORIDE STARCH STEAM (212F) STEARIC ACID STODDARD SOLVENT STYRENE SUGAR LIQUIDS SULFATE, BLACK LIQUORS SULFATE, GREEN LIQUORS SULFATE, WHITE LIQUORS SULFURIC ACID (0-7%) (VTFEP) SULFURIC ACID (100%) H2S04 (VTFEP) SULFURIC ACID (20%) (VTFEP) SULFURIC ACID (50%) (VTFEP) SULFUROUS ACID SULPHUR SULPHUR DIOXIDE (DRY) SULPHUR TRIOXIDE (DRY) SYNTHESIS GAS TALL OIL TANNIC ACID TAR - TAR OIL TARTARIC ACID TETRAETHYL LEAD TITANIUM TETRACHLORIDE T1-CL4 TITANIUM TRICHLORIDE T1-CL3 TOLUENE - TOLUOL TOMATO JUICE TRANSFORMER OIL TRIBUTYL PHOSPHATE TRICHLOROETHYLENE TUNG OIL TURPENTINE UREA VARNISH VEGETABLE OIL, EDIBLE VEGETABLE OIL, NON-EDIBLE VINEGAR WATER, DISTILLED (AREATED) WATER, FRESH WATER, SEA WAX, EMULSIONS WAXES WHISKEY AND WINE XYLENE (DRY) ZINC CHLORIDE ZINC HYDROSULFITE ZINC SULFATE
34
WKM
CT-WKM-210/310
10/06 NP-2M
(-) - Not tested. VTFEP - Virgin TFE Packing. Note: All ladings at ambient temperatures except as noted.
DISTRIBUTED VALVES
TRADEMARK INFORMATION
References in this catalog to registered trademarks or product designations, which are owned by Cameron are as follows: CAMERON CONTROL SEAL DEMCO DUAL SEAL DYNACENTRIC DYNASEAL ENTECH FOSTER GENERAL VALVE GROVE LEDEEN NAVCO NUTRON ORBIT POW-R-SEAL RING-O SAF-T-SEAL TBV TECHNO TEXSTEAM THORNHILL CRAVER TK TOM WHEATLEY TRUSEAL UNIBOLT VALVSERV WHEATLEY WKM References in this catalog to registered trademarks or product designations, which are not owned by Cameron are as follows: Trademark Owner Common Name Comparable Cameron Abbreviated Name (in Trim Charts) FXM
Asahi Glass Company Hoechst Celanese Corporation E.I. DuPont De Nemours & Company Victrex PLC Corp United Kingdom Stoody Deloro Stellite, Inc.
TFE Propylene
Polyetheretherketone
E.I. DuPont De Nemours & Company Poly Tetra Fluoro Ethylene DuPont Dow Elastomers L.L.C. Armco Advanced Materials Corp. Fluoroelastomer 17-4PH Stainless Steel Electroless Nickel Plating
WKM
CT-WKM-210/310
10/06 NP-2M
35
36
WKM
CT-WKM-210/310
10/06 NP-2M
DISTRIBUTED VALVES
DISTRIBUTED VALVES
VALVES & MEASUREMENT 3250 Briarpark Drive, Suite 300 Houston, Texas 77042 USA Toll Free 800 323 9160
For the most current contact and location information go to: www.c-a-m.com