Beruflich Dokumente
Kultur Dokumente
Thinking in Sclar
U.S. Des. Patent No. D496,248S. Other patents pending.
Stainless steel hardware can seize up,
a process called galling. To sig ni cant ly
reduce its like li hood, (1) apply lubricant
to bolts, preferably an anti-seize lu bri cant, avail-
able at auto parts stores, (2) shade hardware
prior to installation, and (3) avoid spinning on
nuts at high speed. See Installation Supplement
910, Galling and Its Prevention, at www.Unirac.
com.
Parts List (Parts are illustrated in exploded views, pp. 24.)
Wrench
Part Qty size
Channel 1
Bracket, left 1
Bracket, right 1
SolarMount standard rail, drilled 2
U-bolt,
3
8 2
Hex head bolt,
3
8 8
9
16
Flange nut,
3
8 4
9
16
Self tapping screw, no.10 zinc 2
Module clip 4*
Module bolt, 4*
7
16
Flat washer, 4*
Flange nut, 4*
7
16
The installer is solely re spon si ble for:
complying with all applicable building codes, in-
cluding any that supercede these instructions;
pole installation appropriate to local wind and soil
conditions;
using only Unirac parts and installer-supplied parts
as specied by Unirac (substitution of parts will
void the warranty);
installing all electrical aspects of the PV array.
Thank you for purchasing a Unirac. Please read these
guidelines completely before proceeding.
This rack is intended for a 2.5-inch (65 mm) Schedule 40
steel pole, outside diameter 2.875 inches (73.0 mm). For
larger diameter poles, Unirac can ll special orders for
larger U-bolts.
* Per module to be mounted. Series 5000 racks include module hardware to
mount 1 or 2 modules, depending on the model number.
Page
3
Installation Manual 501.5 Series 5000
Assembly
Assembly order is not criticalex cept for installation of the self-tap ping
screws, which oc curs last. You may work either from the pole out ward, or you
may com plete the rack/PV module as sem bly before mount ing it to the pole.
Loosely assemble all com po nents.
Be certain that the channel is cen tered on the pole and that brack ets sit with the
piv ot hole above the arc hole.
Pre-drilled hole
SolarMount
rail
Self tapping
screw
Bracket
Pre-drilled hole
Channel
Pivot hole
Arc hole
0803
12.000
2.500
.531
21.000
17.000
7.0
23.750
1.02
SL|, |nc. Maximum
Power Point Tracking
Charge Controller
Solar Lighting |nternational, |nc. Lancaster, SC 29720
Phone +l 803-233-346l Pax +l 803-233-2096 www.solarlightingitl.com
7073 Henr Harris Poad
Lancaster, SC 29720
Phone +l 803-233-346l
Pax +l 803-233-2096
www.solarlightingitl.com
Solar Lighting |nternational, |nc. 7073 Henr Harris Poad Lancaster, SC 29720 Phone +l 803-233-346l Pax +l 803-233-2096
www.solarlightingitl.com
Solar Lighting |nternational, |nc. 7073 Henr Harris Poad Lancaster, SC 29720 Phone +l 803-233-346l Pax +l 803-233-2096
www.solarlightingitl.com
Solar Lighting |nternational, |nc. 7073 Henr Harris Poad Lancaster, SC 29720 Phone +l 803-233-346l Pax +l 803-233-2096
www.solarlightingitl.com
R-8/ 2001
M
-
2
5
0
R
O
A
D
W
A
Y
L
I
G
H
T
I
N
G
GE Lighting Systems, Inc.
www.gelightingsystems.com
Registered Trademark of General Electric Company
Trademark of General Electric Company
Data subject to change without notice
ORDERING NUMBER LOGIC
PRODUCT
IDENT
XXXX
LIGHT
SOURCE
X
VOLTAGE
X
BALLAST
TYPE
X
IES DISTRIBUTION
TYPE
XXX
LENS TYPE (PRISMATIC)
REFRACTOR
X
OPTIONS
XXX
M2RC =
M-250R2 with
Cutoff Optics
S = HPS
C = Merc
Standard:
Lamp not
included.
60Hz
0 = 120/208/
240/277
Multivolt
1 = 120
2 = 208
3 = 240
4 = 277
5 = 480
7 = 120X240
8 = 240V
Ballast 120V PE
Receptacle not
reconnectable
D = 347
F = 120X347
T = 220
W= 230
50Hz
6 = 220
R = 230
Y = 240
NOTE: Dual
voltage connected
for lower voltage
See Ballast Selection Table
A = Autoreg
C = Merc-Reg
G = Mag-Reg with
Grounded Socket Shell
H = HPF Reactor or Lag
M= Mag-Reg
N = NPF Reactor or Lag
P = CWI with Grounded
Socket Shell
See Photometric
Selection Table
S = Short
M = Medium
C = Cutoff
2 = Type II
3 = Type III
See Photometric
Selection Table
A = Acrylic Clear
Globe
G = Glass
L = Polycarbonate
Clear Globe
NOTE:
150 watt Maximum
with Acrylic or
Polycarbonate
Refractors.
C = Charcoal filter
F = Fusing (Not
available with
multivolt or dual
voltage)
J = Line Surge
Protector,
Expulsion Type
WATTAGE
XX
05 =50
07 =70
10 =100
15 =150
(55V)
17 =175
20 =200
21 =100/150
(55V)
25 =250
NOTE: Dual
wattage
connected
for lower
wattage
2
PE FUNCTION
X
1 = None
2 = PE Receptacle
NOTE:
Receptacle connected
same voltage as unit
except as noted. Order
PE Control separately.
M-250R2 LUMINAIRE
WITH CUTOFF OPTICS
APPLICATIONS
For residential streets, access roads, parking lots and other outdoor areas
Universal two-bolt slipfitter
Die-cast aluminum housing with
electrocoat gray paint finish
Adjustable mogul base socket
(street side) E39 standard
ALGLAS
finish on reflector
No-tool PE receptacle
Plug-in ignitor
True 90 cutoffno light
above 90 (meets RP8-2000 for
full cutoff)
External stainless steel bail
latch
CSA Certified unit available,
contact factory
Standard construction is IP55
Plastic Pest guard standard (not
required for 2 in. pipe)
SPECIFICATION FEATURES
All light sources are clear unless otherwise indicated.
PHOTOMETRIC SELECTION TABLE
Light Lens
Wattage Source Type MC2* MC3* SC2*
50,70,100,150 (55 V) HPS A or L N/A 9168 (1A) N/A
50,70,100,150 (55 V) HPS G 7293(2CL) 7292(1CL) N/A
200, 250 HPS G 7306 (2DH) 7305 (1DH) N/A
100, 175, 250 Merc G N/A N/A 7300(1B)
NOTE: N/A=Not Available
*Meets RP8-2000 for full cutoff
IES Distribution Type
Photometric Curve Number 35-17 ----(Soc Pos)
M2RC 15 S 1 N 2 G MC3
F
2001/ R-9
M
-
2
5
0
R
O
A
D
W
A
Y
L
I
G
H
T
I
N
G
GE Lighting Systems, Inc.
www.gelightingsystems.com
Registered Trademark of General Electric Company
Trademark of General Electric Company
Data subject to change without notice
REFERENCES
See Page R-38 for start of Accessories.
See Page R-42 for Explanation of Options and Other Terms Used.
See Pole and Bracket Section Page P-2 for pole selection.
DATA
Approximate Net Weight 20-30 lbs 9-14 kgs
Effective Projected Area
Flat Glass Unit 0.6 sq. ft. max 0.06 sq. M max
Clear Acrylic or
Polycarbonate Globe Unit 1.0 sq. ft. max 0.09 sq. M max
Suggested Mounting Height 20-40 ft. 6-12 M
M-250R2 LUMINAIRE
WITH CUTOFF OPTICS
FIXTURE DIMENSIONS
Light Multi- 347, 240/120
Wattage Source volt 120 208 240 277 480 120X240 120X347 PE R 220 230 220 230 240
50 HPS H,N H,N H,N H,N H,N H,N H,N H,N H,N N/A N/A N/A N/A N/A
70,100,150 (55V) HPS A,H,N A,G,H,M,N,P A,G,H,M,N A,G,H,M,N,P A,G,H,M,N G,M G,H,M,N,P G*,H,M*,N G,H,M,N H,M,N N/A H,M,N H N/A
100/150 (55V) HPS N/A H,N N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
200, 250 HPS A,P A,H,N,P A,H,N,P A,H,N,P A,P A,P A,P A**,P A,H,N H H A,H,N H H
100, 175 Merc C C,N C C,H,N C C C N/A C,H,N N/A N/A N/A N/A N/A
250 Merc C A,C,N C C,H,N C C C N/A C,H,N N/A N/A H N/A H
NOTE: N/A = Not Available
NOTE: *Not available in 120X347 volt
NOTE: **Not available in 200 watt
Ballast Type/Voltage
60Hz 50Hz
BALLAST SELECTION TABLE
M2AC SUGGESTED CATALOG ORDERING NUMBERS
Catalog Number Wattage Light Source Voltage Ballast Refractor Photometric
(60 Hz) Type Type Distribution
M2RC07S1N2GMC3 070 HPS 120 NPF Reactor Glass MC3
M2RC10S1N2GMC3 100 HPS 120 NPF Reactor Glass MC3
M2RC15S0A2GMC3 150 HPS 120 NPF Reactor Glass MC3
All GE suggested catalog ordering numbers come with PE receptacle. PE control must be ordered
separately. Order and install SCCL-PECTL if no PE is desired.
Multivolt ballasts can be for either 120, 208, 240, or 277 volt incoming power supply.