Beruflich Dokumente
Kultur Dokumente
February
2008
World-Class Manufacturing
Greenhecks skilled production workers use cost-effective machines and unique dies designed and built by our own engineers to add innovative features and greater strength to our centrifugal exhaust fans. Our advanced manufacturing processes and quality control procedures always ensure the highest product quality. And just to be sure you get the peace-of-mind you expect when you specify Greenheck, our assembly inspectors test run and monitor every fan before it leaves the factory. Results of these tests are kept in permanent records for future reference.
6 7
Fan Shaft - Is 1-inch minimum in diameter and is precisely sized, ground, and polished so the first critical speed is at least 25% over the maximum operating speed, which results in longer fan life. Bearings - Lubricatable cast pillow block and are air handling quality extended life L10 > 100,000 hours (L50 average life > 500,000 hours) True Vibration Isolation - Lowers sound levels and reduces vibration, which increases the fans life since true vibration has no steel to steel contact. Clean Out Port - Allows the outside of the wheel to be cleaned through a four-inch diameter removable plug in the windband. Non-Stick Coated Steel Wheel - Heavy weight steel wheel with a dry lubricate coating eliminates imbalance in heavy grease applications. The steel wheel is a backwardinclined, non-overloading centrifugal type. Drain Trough - All grease and water is collected at one-point for easy disposal. Curb Cap with Mounting Holes - Prepunched mounting holes in the steel curb cap to ensure correct attachment to the roof. Hinged Curb Cap with Cables - Allows entire fan to tilt away for access to wheel and ductwork for inspection and cleaning. Shipped for field assembly. Leakproof Construction - One-piece fully welded windband to curb cap. Assures no grease will leak onto roof through the fans seams.
11 12
13 14
15 16
17 18
19
oversized 150% of driven horsepower. Machined cast steel pulleys are adjustable for final system balancing. Belts are static free and oil resistant. Motor Cover - Is easily removed for access to the steel motor compartment and drive assembly. Powder Coated - Unit is constructed of a minimum of 16 gauge galvaneal steel. Entire unit is powder coated with a chemical resistant Permatector finish. Motor - Carefully matched to the fan load and is mounted out of air stream. Windband - Unique spun from galvaneal steel achieves superior strength & consistent material thickness. Nema-3R Disconnect Switch Mounted & Wired Motor and switch are prewired to specified voltage. Motor Cooling Tube - Maximum motor life is achieved through positive motor cooling with fresh outside air being continuously drawn through the large breather tube directly over the motor. Name Plate - Exact model and serial identification on a permanent stamped aluminum plate. Heat Baffle - Extends motor life by reducing the amount of heat that penetrates through the bottom of the motor support pan. Lifting Lugs - Located under motor compartment for ease of lifting unit during installation.
1 10 2
11
12 4 3 8 18 19 13 16 14 15
17
9 6 7
Coatings: Wide variety of coatings and colors are available for decorative to acidic applications. Permatector is our standard coating. Typically used for applications that require corrosion resistance in indoor and outdoor environments. Hi-Pro Polyester is resistant to salt water, chemical fumes and moisture in more corrosive atmospheres. Typically used for applications that require superior chemical resistance, excellent abrasion and outdoor UV protection. This coating exceeds protective qualities of Air Dried Heresite and Air Dry Phenolic. Baked Enamel Decorative Coatings are heat cured enamels applied either as wet paints or electrostatic powders. Customers can choose from 16 standard decorative colors or color match any color.
PERMATECTOR
HI-PRO POLYESTER
HI-PRO POLYESTER
BAKED ENAMEL
Windband Extension: Tube that raises fans discharge an additional 36in. for special code requirements. Curb Seal: Rubber seal between fan and curb to assure proper sealing when attached to a curb. Roof Curbs: Wide variety of roof curbs are available for mounting the fan to the roof, including: vented, flanged, pitched.
Grease Trap with Absorbent Material: Same as above with an absorbent material to collect grease residue and repel water for easy periodic disposal.
Tie Down Points: Four brackets located on the windband for securing the fan in heavy wind applications.
Velocity Accelerator: Increases fan outlet/ discharge velocity. Up to 3,000 feet per minute.
NEMA 3R Disconnect factory wired from motor to disconnect through the breather tube (Optional)
Welded Duct by others min. of 18 in. above roof deck per NFPA
Mounting Bolt Hole Circle Reco Wall Vented Curb Extension External Wiring Liquid Tight Flexible Conduit by Others
8"min.
Roof Deck
Installation must include a means for inspecting, cleaning and servicing the exhaust fan. (e.g. Hinged Curb Cap) No dampers are to be installed in the system.
Greenhecks Performance Enhancing Lip (PEL) helps direct air to the filter and improves capture and performance Full length, fully welded integral grease trough An integral 3-inch airspace that meets NFPA 96 clearance requirements against limited combustibles Constructed of 304 / 430 18 ga. stainless steel. Standing seam construction for added strength Redesigned flat light panels allows for lights to be installed vertically and simplified field installation Fully welded joints - no caulk
3
6 5
2 3
4 7 2 1
Grease Grabber dual filtration system works with the Grease-X-Tractor filter to remove 80% of the grease from the kitchen exhaust. Available in stainless steel. The Grease-XTractor high efficiency filter has twice the grease extraction capability of a baffle filter. Available in aluminum or stainless steel.
The high velocity cartridge filters offers dry cartridge performance at a lower cost. Available in aluminum or stainless steel. Baffle type filters are the traditional choice for inexpensive grease removal. Available in aluminum, stainless steel, or non-stick coated. 7
Total Fasteners 20 20
H-GPF or SD curb
1/4 in. (6 mm) fastener minimum 5/16 in. (8 mm) recommended See table for fastener quantities
Fasteners on each side of the fan are to be installed with one fastener 4 in. (102 mm) from each edge and one fastener centered. The remaining fasteners are to be equally spaced.
Corner Detail
1 in. (32 mm)
H-GPF Curb Height 8 to 18 in. (203 to 457 mm) (Optional 24 in. (610 mm) SD Curb) Minimum Concrete Strength of 2000 PSI Minimum 1-3/4 in. (44 mm) edge distance
Roof Opening
2-1/2 in. (64 mm) Embedment Recommended minimum 1-5/8 in. (41 mm)
Typical Anchoring
Metal Building/Steel Deck Anchoring
Outside of Roof Curb 1 in. (25 mm) less than Fan Curb Cap
Corner Detail
1 in. (32 mm)
H-GPF Curb Height 8 to 18 in. (203 to 457 mm) (Optional 24 in. (610 mm) SD Curb) 1 in. (25 mm) Insulation
Roof Opening
Use #12-14 self-drilling screws or equal. Fasteners one on each corner as detailed. Each side at center of unit. Maximum fastener spacing of 8 in. (203 mm), add additional fasteners to satisfy.
Minimum 12 ga Steel
Corner Detail
1 in. (32 mm)
H-GPF Curb Height 8 to 18 in. (203 to 457 mm) (Optional 24 in. (610 mm) SD Curb)
Use #12 Wood Screws or equal into minimum No. 1/No. 2 Southern Pine wood support. Fasteners one on each corner as detailed. Each side at center of unit. Maximum fastener spacing of 6 in. (152 mm), add additional fasteners to satisfy.
Roof Opening
USGF - 140 HP - 5
Configuration
Ultimate Steel Grease Fan
Motor HP
4 = 14 10 = 1 3 = 13 15 = 112 5 = 12 20 = 2 7 = 34 30 = 3 50 = 5 75 = 712
Fan Size
140 through 200
Pressure Level
HP - High Pressure Wheel XP - Extended High Pressure Wheel
H-
26 (660) Roof Opening = 18 x 18 (470 x 470) Windband Thickness = 0.051 (1.3) Motor Cover Thickness = 0.040 (1.0) Curb Cap Thickness = 0.064 (1.6) ^Approximate Unit Weight = 125 lb. (57 kg)
134 (44)
Do
no
All dimensions in inches (millimeters). *May be greater depending on motor. ^Weight shown is largest cataloged Open Drip Proof motor. Model Number USGF-140-4 Motor hp 1/4 590 Fan rpm CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM / Static Pressure in inches wg 0.375 0.5 0.75 1
715
840
965
0 1069 0.04 5.0 1295 0.06 6.0 1521 0.10 7.1 1748 0.15 8.6 2001 0.23 10.9 2192 0.30 12.2 2337 0.36 13.2 2518 0.45 14.9 2708 0.56 17.2 2889 0.69 20 3125 0.87 26
0.125 851 0.04 4.5 1130 0.07 6.0 1387 0.11 7.3 1635 0.16 8.7 1906 0.24 10.8 2106 0.31 12.2 2258 0.38 13.3 2445 0.47 14.7 2640 0.58 16.5 2826 0.70 19.0 3066 0.88 23
0.25
ele ct
ts
to t
he le
ft o f th is s yste mc urve
1.25
1.5
1.75
885 0.07 5.1 1217 0.11 6.8 1499 0.17 8.5 1793 0.25 10.6 2006 0.32 11.7 2166 0.39 12.7 2362 0.48 14.2 2565 0.6 16.3 2757 0.72 18.5 3005 0.90 22
MAXIMUM BHP AT A GIVEN RPM = (RPM/1726)3 MAXIMUM RPM = 1725 TIP SPEED (ft/min.) = RPM x 3.829 MAXIMUM MOTOR FRAME SIZE = 145T AVERAGE DISCHARGE VELOCITY (FPM) = CFM/1.72
969 0.11 6.2 1333 0.17 8.1 1667 0.26 10.3 1896 0.33 11.6 2065 0.40 12.6 2271 0.50 13.2 2483 0.61 15.6 2683 0.74 19.5 2936 0.92 24
1103 0.17 7.7 1515 0.26 10.0 1773 0.34 11.2 1957 0.41 12.3 2174 0.51 12.9 2396 0.62 13.9 2602 0.75 16.1 2865 0.94 24
998 0.23 9.6 1443 0.34 10.9 1691 0.42 12.0 1949 0.52 12.1 2202 0.64 12.5 2430 0.77 13.3 2711 0.97 15.1
1221 0.37 11.3 1643 0.51 11.0 1967 0.65 12.2 2225 0.79 12.3 2539 0.99 13.4
Performance certified is for installation type A: Free inlet, Free outlet. Power rating (BHP) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values shown are for installation type A: Free inlet hemispherical sone levels. The AMCA Certified Ratings Seal applies to sone ratings only.
10
H-
26 (660) Roof Opening = 18 x 18 (470 x 470) Windband Thickness = 0.051 (1.3) Motor Cover Thickness = 0.040 (1.0) Curb Cap Thickness = 0.064 (1.6) ^Approximate Unit Weight = 125 lb. (57 kg)
134 (44)
Do
All dimensions in inches (millimeters). *May be greater depending on motor. ^Weight shown is largest cataloged Open Drip Proof motor. Model Number USGF-140HP-4 Motor hp 1/4 895 Fan rpm CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM / Static Pressure in inches wg 1.25 1.5 1.75 2
1037
1179
1321
2035
2110
0.5 331 0.06 6.1 566 0.10 6.7 733 0.13 8.9 878 0.18 12.1 1016 0.24 14.2 1146 0.31 15.2 1256 0.38 16.1 1363 0.46 17.0 1463 0.54 18.1 1528 0.60 18.9 1592 0.67 19.8
0.75
no
ts ele ct
to th
e le
ft o
f thi
W.G.
2.25
2.5
2.75
MAXIMUM BHP AT A GIVEN RPM = (RPM/2285)3 MAXIMUM RPM = 2110 TIP SPEED (ft/min.) = RPM x 3.829 MAXIMUM MOTOR FRAME SIZE = 145T AVERAGE DISCHARGE VELOCITY (FPM) = CFM/1.72
563 0.14 9.2 756 0.19 11.6 920 0.26 13.5 1063 0.33 14.4 1178 0.40 15.4 1292 0.48 16.6 1399 0.57 17.7 1468 0.63 18.5 1536 0.70 19.3
591 0.19 13.6 798 0.26 13.2 965 0.34 14.2 1098 0.42 15.0 1219 0.50 16.2 1330 0.59 17.4 1402 0.66 18.2 1473 0.72 19.1
642 0.26 15.5 846 0.34 14.0 999 0.43 14.9 1137 0.52 16.0 1260 0.61 17.2 1335 0.68 18.0 1409 0.75 19.0
704 0.34 15.2 879 0.43 14.7 1042 0.52 15.9 1176 0.62 17.1 1261 0.69 18.0 1341 0.77 18.9
747 0.42 15.7 924 0.52 15.6 1086 0.63 17.0 1175 0.70 17.8 1262 0.78 18.8
800 0.51 16.1 970 0.62 16.8 1077 0.70 17.7 1178 0.78 18.6
804 0.73 20
Performance certified is for installation type A: Free inlet, Free outlet. Power rating (BHP) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values shown are for installation type A: Free inlet hemispherical sone levels. The AMCA Certified Ratings Seal applies to sone ratings only.
11
H-
26 (660) Roof Opening = 18 x 18 (470 x 470) Windband Thickness = 0.051 (1.3) Motor Cover Thickness = 0.040 (1.0) Curb Cap Thickness = 0.064 (1.6) ^Approximate Unit Weight = 131 lb. (59 kg)
134 (44)
Do
t no
All dimensions in inches (millimeters). *May be greater depending on motor. ^Weight shown is largest cataloged Open Drip Proof motor. Model Number USGF-160-4 Motor hp 1/4 730 Fan rpm CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM / Static Pressure in inches wg 0.375 0.5 0.625 0.75 1 1.25 1.5 1389 MAXIMUM BHP AT A GIVEN RPM = (RPM/1365)3 0.15 MAXIMUM RPM = 1390 7.8 TIP SPEED (ft/min.) = RPM x 4.352 1596 MAXIMUM MOTOR FRAME SIZE = 145T 0.18 AVERAGE DISCHARGE VELOCITY (FPM) = CFM/1.72 8.4 1790 1512 0.22 0.21 9.1 9.0 1974 1744 1365 0.26 0.26 0.24 9.9 9.7 9.7 2300 2109 1893 1584 0.35 0.35 0.34 0.33 11.2 10.8 10.6 10.5 2552 2382 2199 1992 0.44 0.44 0.43 0.43 12.4 12.1 11.8 11.6 2796 2641 2475 2297 1770 0.53 0.54 0.53 0.52 0.49 13.8 13.5 13.1 12.9 12.2 3053 2911 2764 2606 2246 0.65 0.65 0.66 0.65 0.64 15.4 15.0 14.7 14.5 14.0 3301 3172 3036 2894 2583 2163 0.78 0.79 0.79 0.79 0.78 0.75 17.2 16.8 16.5 16.3 15.8 15.2 3502 3383 3253 3124 2843 2510 0.90 0.91 0.91 0.92 0.90 0.89 18.7 18.3 18.0 17.8 17.4 16.9 3698 3584 3464 3340 3078 2785 2394 1.03 1.04 1.04 1.05 1.04 1.03 1.00 20 19.9 19.6 19.4 19.0 18.6 18.0
778
826
1390
0 2098 0.13 8.1 2236 0.16 8.9 2374 0.20 9.9 2515 0.23 11.0 2774 0.31 12.4 2984 0.39 13.7 3191 0.47 15.0 3415 0.58 16.7 3636 0.70 18.5 3817 0.81 20 3996 0.93 22
0.125 1905 0.15 8.0 2058 0.18 8.7 2209 0.22 9.6 2362 0.26 10.6 2637 0.34 12.0 2857 0.42 13.3 3072 0.51 14.6 3304 0.62 16.3 3532 0.74 18.1 3718 0.85 19.6 3901 0.97 21
0.25 1669 0.15 7.8 1843 0.19 8.5 2010 0.22 9.3 2177 0.26 10.1 2477 0.35 11.5 2712 0.43 12.8 2941 0.53 14.2 3186 0.64 15.8 3426 0.77 17.7 3619 0.89 19.2 3806 1.01 21
Performance certified is for installation type A: Free inlet, Free outlet. Power rating (BHP) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values shown are for installation type A: Free inlet hemispherical sone levels. The AMCA Certified Ratings Seal applies to sone ratings only.
12
le
se
ct
to th el ef t
of
th i s sy ste
mc
urv e
H-
W.G.
26 (660) Roof Opening = 18 x 18 (470 x 470) Windband Thickness = 0.051 (1.3) Motor Cover Thickness = 0.040 (1.0) Curb Cap Thickness = 0.064 (1.6) ^Approximate Unit Weight = 131 lb. (59 kg)
134 (44)
t no Do
All dimensions in inches (millimeters). *May be greater depending on motor. ^Weight shown is largest cataloged Open Drip Proof motor. Model Number USGF-160HP-4 Motor hp 1/4 825 Fan rpm CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM / Static Pressure in inches wg 0.875 1 1.25 1.5
910
995
1690
0.5 889 0.12 7.0 1129 0.16 8.3 1331 0.21 9.6 1487 0.25 11.0 1697 0.32 12.8 1882 0.40 13.1 2053 0.48 14.4 2253 0.59 16.3 2433 0.70 18.1 2573 0.80 19.6 2722 0.92 21
0.625
0.75
le ct
se
to t
he
lef t
of thi s sy ste mc
ur v e
1.75
2.25
956 0.16 7.8 1208 0.21 9.3 1377 0.26 10.6 1608 0.33 12.7 1799 0.41 12.8 1975 0.49 13.8 2180 0.60 15.8 2368 0.72 17.7 2516 0.82 19.2 2671 0.94 21
MAXIMUM BHP AT A GIVEN RPM = (RPM/1660)3 MAXIMUM RPM = 1690 TIP SPEED (ft/min.) = RPM x 4.352 MAXIMUM MOTOR FRAME SIZE = 145T AVERAGE DISCHARGE VELOCITY (FPM) = CFM/1.72
1042 0.21 8.8 1252 0.26 10.2 1504 0.34 12.2 1715 0.42 12.5 1897 0.50 13.3 2108 0.61 15.2 2301 0.73 17.2 2452 0.83 18.8 2611 0.95 21
1093 0.26 9.8 1395 0.34 11.7 1617 0.43 12.0 1816 0.51 12.8 2036 0.63 14.7 2233 0.74 16.8 2387 0.85 18.4 2550 0.97 20
1252 0.34 11.3 1519 0.43 11.5 1724 0.52 12.3 1961 0.64 14.3 2165 0.76 16.4 2322 0.86 18.1 2488 0.98 20
1218 0.42 10.6 1513 0.52 11.3 1790 0.65 13.5 2015 0.78 15.7 2190 0.89 17.5 2365 1.01 19.5
1577 0.65 12.3 1855 0.79 14.9 2037 0.90 16.9 2228 1.03 19.1
Performance certified is for installation type A: Free inlet, Free outlet. Power rating (BHP) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values shown are for installation type A: Free inlet hemispherical sone levels. The AMCA Certified Ratings Seal applies to sone ratings only.
13
H-
26 (660) Roof Opening = 18 x 18 (470 x 470) Windband Thickness = 0.051 (1.3) Motor Cover Thickness = 0.040 (1.0) Curb Cap Thickness = 0.064 (1.6) ^Approximate Unit Weight = 131 lb. (59 kg)
134 (44)
All dimensions in inches (millimeters). *May be greater depending on motor. ^Weight shown is largest cataloged Open Drip Proof motor. Model Number USGF-160XP-5 Motor hp 1/2 1550 Fan rpm CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM / Static Pressure in nches wg 1.75 2 2.25 2.5
1648
1942
2432
2525
1 968 0.34 10.0 1157 0.42 11.1 1322 0.52 12.1 1515 0.65 13.7 1599 0.71 14.3 1684 0.77 15.0 1861 0.93 16.6 1946 1.01 17.5 2076 1.17 19.0 2226 1.36 21 2339 1.52 22
1.25
1.5
Do
n ot
sele ct to the
left of
this sy stem cu r
W.G.
ve
2.75
3.25
854 0.39 10.2 1116 0.49 11.4 1359 0.63 13.1 1456 0.70 13.9 1552 0.78 14.7 1743 0.95 16.4 1834 1.03 17.3 1974 1.18 18.7 2134 1.36 20 2250 1.52 22
MAXIMUM BHP AT A GIVEN RPM = (RPM/2170)3 MAXIMUM RPM = 2525 TIP SPEED (ft/min.) = RPM x 3.534 MAXIMUM MOTOR FRAME SIZE = 145T AVERAGE DISCHARGE VELOCITY (FPM) = CFM/1.72
726 0.43 10.9 1139 0.60 12.3 1271 0.68 13.2 1392 0.76 14.1 1611 0.94 15.9 1713 1.04 17.0 1865 1.2 18.5 2031 1.38 20 2155 1.54 22
744 0.52 12.2 984 0.63 12.6 1161 0.72 13.4 1451 0.91 15.4 1578 1.01 16.4 1741 1.18 18.1 1926 1.40 20 2056 1.56 22
777 0.63 13.6 1226 0.87 14.8 1395 0.99 15.9 1597 1.16 17.5 1804 1.38 19.6 1946 1.56 21
869 0.78 15.1 1127 0.92 15.5 1415 1.12 17.1 1660 1.35 19.1 1828 1.53 21
634 0.73 16.7 1134 1.04 16.8 1483 1.31 18.7 1676 1.50 20
810 1.16 22
Performance certified is for installation type A: Free inlet, Free outlet. Power rating (BHP) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values shown are for installation type A: Free inlet hemispherical sone levels. The AMCA Certified Ratings Seal applies to sone ratings only.
14
H-
30 (762) Roof Opening = 20 x 20 (521 x 521) Windband Thickness = 0.051 (1.3) Motor Cover Thickness = 0.040 (1.0) Curb Cap Thickness = 0.064 (1.6) ^Approximate Unit Weight = 190 lb. (86 kg)
134 (44)
s ot on
All dimensions in inches (millimeters). *May be greater depending on motor. ^Weight shown is largest cataloged Open Drip Proof motor. Model Number USGF-180-4 Motor hp 1/4 630 Fan rpm CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM / Static Pressure in inches wg 0.5 0.75 1 1.25
745 USGF-180-3 1/3 820 USGF-180-5 1/2 940 USGF-180-7 3/4 1010
1495
0 2380 0.13 7.1 2815 0.22 9.2 3098 0.30 11.2 3551 0.45 13.8 3816 0.56 15.4 4061 0.67 16.5 4477 0.90 18.5 4817 1.12 21 5138 1.36 23 5402 1.58 25 5648 1.80 28
0.125 2154 0.15 6.4 2617 0.24 8.6 2916 0.32 10.4 3389 0.47 13.5 3664 0.58 15.2 3919 0.70 16.2 4348 0.93 17.9 4697 1.15 20 5026 1.39 23 5296 1.62 25 5546 1.84 27
0.25 1861 0.16 5.5 2448 0.26 8.1 2759 0.34 10.0 3243 0.49 13.1 3526 0.61 14.9 3786 0.73 15.8 4224 0.96 17.1 4578 1.19 19.5 4913 1.43 22 5189 1.66 25 5443 1.89 27
lec t
to the
lef
to f th is s yst em cur ve
1.5
1.75
1763 0.25 7.1 2257 0.34 9.0 2879 0.52 12.4 3242 0.65 14.7 3554 0.78 151.5 4005 1.01 16.5 4369 1.24 18.7 4710 1.49 21 4993 1.72 24 5254 1.96 26
MAXIMUM BHP AT A GIVEN RPM = (RPM/1167)3 MAXIMUM RPM = 1495 TIP SPEED (ft/min.) = RPM x 4.843 MAXIMUM MOTOR FRAME SIZE = 184T AVERAGE DISCHARGE VELOCITY (FPM) = CFM/2.92
2363 0.50 11.2 2799 0.64 13.7 3141 0.78 14.7 3703 1.04 16.0 4163 1.30 18.2 4532 1.56 21 4819 1.79 23 5082 2.02 25
2105 0.58 11.8 2652 0.75 13.3 3336 1.04 15.2 3799 1.30 17.5 4232 1.58 20 4593 1.83 22 4921 2.10 25
2841 0.99 14.4 3437 1.28 16.7 3912 1.58 19.2 4270 1.83 22 4598 2.10 24
2930 1.22 15.9 3537 1.54 18.3 3968 1.83 21 4313 2.10 23
Performance certified is for installation type A: Free inlet, Free outlet. Power rating (BHP) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values shown are for installation type A: Free inlet hemispherical sone levels. The AMCA Certified Ratings Seal applies to sone ratings only.
15
H-
W.G.
30 (762) Roof Opening = 20 x 20 (521 x 521) Windband Thickness = 0.051 (1.3) Motor Cover Thickness = 0.040 (1.0) Curb Cap Thickness = 0.064 (1.6) ^Approximate Unit Weight = 190 lb. (86 kg)
1 4 (44)
3
e ts no o D
All dimensions in inches (millimeters). *May be greater depending on motor. ^Weight shown is largest cataloged Open Drip Proof motor. CFM / Static Pressure in inches wg 1.25 1.5 1.75 2
Motor hp 1/4
Fan rpm 795 CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones
845 USGF-180HP-3 1/3 925 USGF-180HP-5 1/2 1065 USGF-180HP-7 3/4 1215 USGF-180HP-10 1 1275
1685
0.5 1570 0.22 8.3 1799 0.26 9.5 2104 0.34 10.8 2581 0.50 13.8 3063 0.72 15.0 3253 0.82 16.7 3441 0.93 18.7 3735 1.13 22 4035 1.36 24 4273 1.58 25 4495 1.79 27
0.75
le c
tt ot
he lef to
f th is s yst em cur ve
2.25
2.5
2.75
MAXIMUM BHP AT A GIVEN RPM = (RPM/1315)3 MAXIMUM RPM = 1685 TIP SPEED (ft/min.) = RPM x 4.843 MAXIMUM MOTOR FRAME SIZE = 184T AVERAGE DISCHARGE VELOCITY (FPM) = CFM/2.92
1688 0.35 9.8 2323 0.52 12.5 2868 0.76 14.5 3066 0.87 15.8 3261 0.98 17.4 3566 1.19 21 3884 1.43 23 4136 1.64 24 4369 1.86 26
1933 0.53 12.4 2626 0.78 14.0 2853 0.89 15.4 3075 1.02 17.0 3401 1.23 19.7 3728 1.48 22 3986 1.70 23 4226 1.93 25
2286 0.79 13.4 2566 0.91 14.9 2839 1.04 16.6 3206 1.26 19.3 3574 1.53 21 3840 1.76 23 4085 1.99 26
1854 0.75 12.9 2209 0.89 14.3 2523 1.04 16.1 2964 1.27 18.9 3376 1.55 20 3674 1.79 22 3945 2.04 24
2156 1.01 15.6 2669 1.28 18.4 3135 1.56 19.8 3485 1.81 21 3768 2.07 23
2320 1.24 17.9 2859 1.57 19.3 3233 1.82 21 3575 2.08 22
2766 2.04 20
Performance certified is for installation type A: Free inlet, Free outlet. Power rating (BHP) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values shown are for installation type A: Free inlet hemispherical sone levels. The AMCA Certified Ratings Seal applies to sone ratings only.
16
H-
W.G.
30 (762) Roof Opening = 20 x 20 (521 x 521) Windband Thickness = 0.051 (1.3) Motor Cover Thickness = 0.040 (1.0) Curb Cap Thickness = 0.064 (1.6) ^Approximate Unit Weight = 213 lb. (97 kg)
134 (44)
n Do
All dimensions in inches (millimeters). *May be greater depending on motor. ^Weight shown is largest cataloged Open Drip Proof motor. Model Number USGF-200-4 Motor hp 1/4 500 Fan rpm CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM / Static Pressure in inches wg 0.375 0.5 0.75 1
605 USGF-200-3 1/3 665 USGF-200-5 1/2 760 USGF-200-7 3/4 820
1210
0 2812 0.14 6.2 3403 0.25 8.1 3740 0.33 9.4 4275 0.49 12.1 4612 0.61 14.1 4922 0.75 16.3 5400 0.98 18.7 5793 1.22 21 6187 1.48 23 6496 1.72 24 6806 1.97 25
0.125 2386 0.15 5.4 3054 0.26 7.4 3422 0.34 8.8 3994 0.51 11.7 4350 0.63 14.1 4676 0.77 16.3 5176 1.01 18.4 5585 1.24 21 5992 1.51 23 6311 1.74 24 6628 2.00 24
0.25 1822 0.15 4.6 2675 0.26 6.7 3096 0.35 8.1 3718 0.52 10.9 4098 0.65 13.0 4439 0.78 15.2 4958 1.03 17.7 5380 1.26 20 5798 1.53 23 6125 1.77 23 6451 2.03 23
ot
se lec t
to the
left
of t h
is sy stem
curv e
1.25
1.5
1.75
2144 0.25 6.1 2699 0.35 7.5 3413 0.52 10.1 3828 0.65 12.2 4192 0.79 14.7 4742 1.04 17.0 5179 1.28 19.2 5610 1.55 22 5946 1.79 23 6279 2.05 23
MAXIMUM BHP AT A GIVEN RPM = (RPM/946)3 MAXIMUM RPM = 1210 TIP SPEED (ft/min.) = RPM x 5.595 MAXIMUM MOTOR FRAME SIZE = 184T AVERAGE DISCHARGE VELOCITY (FPM) = CFM/2.92
2073 0.33 7.0 3048 0.51 9.4 3523 0.65 11.4 3922 0.79 13.5 4508 1.04 16.4 4968 1.29 18.7 5421 1.57 21 5767 1.81 22 6108 2.07 22
2606 0.61 10.7 3240 0.78 12.4 3985 1.04 15.0 4503 1.29 17.5 5006 1.57 20 5383 1.81 21 5748 2.09 21
3169 1.00 14.4 3917 1.27 16.4 4529 1.57 19.3 4948 1.81 20 5350 2.09 21
2972 1.18 16.8 3861 1.53 18.6 4410 1.80 19.2 4892 2.08 19.8
3365 1.88 21
Performance certified is for installation type A: Free inlet, Free outlet. Power rating (BHP) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values shown are for installation type A: Free inlet hemispherical sone levels. The AMCA Certified Ratings Seal applies to sone ratings only.
17
H-
30 (762) Roof Opening = 20 x 20 (521 x 521) Windband Thickness = 0.051 (1.3) Motor Cover Thickness = 0.040 (1.0) Curb Cap Thickness = 0.064 (1.6) ^Approximate Unit Weight = 213 lb. (97 kg)
134 (44)
t no Do
All dimensions in inches (millimeters). *May be greater depending on motor. ^Weight shown is largest cataloged Open Drip Proof motor. Model Number USGF-200HP-5 Motor hp 1/2 740 Fan rpm CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM BHP Sones CFM / Static Pressure in inches wg 1.25 1.5 1.75 2
1600
0.5 2024 0.31 8.1 2779 0.51 10.5 3094 0.62 12.2 3397 0.75 14.5 3851 0.98 16.9 4207 1.20 19.0 4558 1.44 22 4837 1.67 23 5110 1.91 24 5382 2.18 26 5943 2.81 29
0.75
ec
l se
tt ot he
lef t
of th
is s yst em c
W.G.
urv e
2.25
2.5
2.75
2317 0.52 9.5 2711 0.64 11.5 3067 0.78 13.7 3561 1.02 16.2 3944 1.24 18.1 4312 1.49 21 4606 1.71 23 4898 1.96 24 5186 2.23 25 5775 2.88 28
MAXIMUM BHP AT A GIVEN RPM = (RPM/1093)3 MAXIMUM RPM = 1600 TIP SPEED (ft/min.) = RPM x 5.595 MAXIMUM MOTOR FRAME SIZE = 184T AVERAGE DISCHARGE VELOCITY (FPM) = CFM/2.92
2092 0.62 10.6 2637 0.79 13.2 3242 1.04 15.7 3661 1.27 17.5 4055 1.53 20 4369 1.76 22 4674 2.01 24 4972 2.28 25 5581 2.93 29
2806 1.04 15.5 3321 1.29 17.3 3789 1.56 19.7 4116 1.79 21 4436 2.05 23 4752 2.33 25 5385 2.99 30
2850 1.26 17.5 3433 1.56 19.3 3826 1.82 21 4195 2.09 21 4521 2.37 23 5182 3.03 29
2944 1.53 19.8 3482 1.82 21 3880 2.09 22 4269 2.40 23 4971 3.08 26
4189 3.13 28
3760 3.06 31
Performance certified is for installation type A: Free inlet, Free outlet. Power rating (BHP) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values shown are for installation type A: Free inlet hemispherical sone levels. The AMCA Certified Ratings Seal applies to sone ratings only.
18
Specifications
Spun steel exhaust fans shall be centrifugal belt driven type. Fan wheel shall be centrifugal backward inclined type. The wheel shall be constructed of steel and coated with a non-stick coating similar to Teflon as manufactured by Du Pont. Wheel shall include a wheel cone carefully matched to the inlet cone for precise running tolerances. Wheels shall be statically and dynamically balanced. The fan housing shall be constructed of 16 gauge galvaneal steel with a rigid internal support structure and shall be leakproof. The fan housing shall be constructed with a one piece windband with an integral rolled bead for added strength and shall be joined to the curb cap with a continuously welded seam. Fans windband shall have a clean out port, a 4-inch diameter hole on the outside of the fans windband with a grease repellent compression rubber fit, allowing access to entire wheel for cleaning. Motors shall be heavy duty ball bearing type, carefully matched to the fan load, and furnished at the specified voltage, phase and enclosure. Drive frame assembly shall be constructed of heavy gauge galvanized steel. Motors and drives shall be mounted on heavy duty true vibration isolators, out of the airstream. Fresh air for motor cooling shall be drawn into the motor compartment through a ten square inch tube free of discharge contaminants. Motors and drives shall be readily accessible for maintenance. Precision ground and polished 1-inch minimum diameter fan shafts shall be mounted in cast pillow block lubricatable ball bearings. Bearings shall be selected for a minimum L10 life in excess of 100,000 hours (L50 average life of 500,000 hours) at maximum cataloged operating speed. Dual drives shall be sized for a minimum of 150% of driven horsepower. Pulleys shall be of the cast type, keyed and securely attached to the wheel and motor shafts. Motor pulleys shall be adjustable for final system balancing. All fans shall have a dual belt and pulley system. A NEMA3R disconnect switch shall be factory installed and wired from the fan motor to a junction box installed outside the motor compartment. All fans shall bear the AMCA Certified Ratings Seal for sound and air performance. Each fan shall bear a permanently affixed manufacturers engraved metal nameplate containing the model number and individual serial number for future identification. Fans shall be Listed by Underwriters Laboratory for UL/cUL 762 Listed for all electrical components and grease removal. Hinge kit shall be constructed of heavy gauge hinges and shall include hold open cables for field installation. Grease trap shall include the drain connection. The unit shall collect grease and water from the fan and extract the grease from the water for ease of grease disposal. Fans shall be model USGF as manufactured by Greenheck Fan Corporation in Schofield, Wisconsin.
19 19
Model SWB centrifugal backward inclined belt driven utility fans are designed for supply, exhaust and return air applications requiring higher discharge velocities and high static pressures. The SWB Series 100 is for general clean air applicators. The SWB Series 200 fans are constructed with heavy gauge steel. Designed for light industrial duty and grease applications with capacities ranges up to 2,7000 cfm (45,900 m3/hr) and up to 5 in. wg (1250 Pa) of static pressure. SWB fans can be mounted indoors or outdoors.
Model TCB inline belt driven fans are the ideal choice for installations with straight-through air flow in ducted systems. The wheels used are designed to provide higher efficiencies and lower sound levels. The fan itself can be mounted horizontally or vertically. Performance capacities ranges up to 24,000 cfm (40,800 m3/hr) and up to 4 in. wg (1,000 Pa) of static pressure.
Our Warranty
Greenheck warrants this equipment to be free from defects in material and workmanship for a period of one year from the purchase date. Any units or parts which prove defective during the warranty period will be replaced at our option when returned to our factory, transportation prepaid. Motors are warranted by the motor manufacturer for a period of one year. Should motors furnished by Greenheck prove defective during this period, they should be returned to the nearest authorized motor service station. Greenheck will not be responsible for any removal or installation costs. As a result of our commitment to continuous improvement, Greenheck reserves the right to change specifications without notice.
Prepared to Support Green Building Efforts
Catalog USGF Rev. 5 February 2008 Copyright 2008 Greenheck Fan Corp.