Beruflich Dokumente
Kultur Dokumente
and OMEW
Orbital motors
Technical
Information
F300030.TIF
A WIDE RANGE OF
HYDRAULIC MOTORS
Sauer-Danfoss is a world leader within production of low speed hydraulic motors with
high torque. We can offer more than 1600 different hydraulic motors, categorised in
types, variants and sizes (incl. different shaft versions).
The motors vary in size (rated displacement) from 8 cm3 [0.50 in3] to 800 cm3 [48.9 in3]
per revolution.
Speeds range up to approx. 2500 min-1 (rpm) for the smallest type and up to approx
600 min-1 (rpm) for the largest type.
Maximum operating torques vary from 13 Nm [115 lbfin] to 2700 Nm [24.000 lbfin]
(peak) and maximum outputs are from 2.0 kW [2.7 hp] to 70 kW [95 hp].
Characteristic features:
Smooth running over the entire speed range
Constant operating torque over a wide speed range
High starting torque
High return pressure without the use of drain line (High pressure shaft seal)
High efficiency
Long life under extreme operating conditions
Robust and compact design
High radial and axial bearing capacity
For applications in both open and closed loop hydraulic systems
Suitable for a wide variety of hydraulics fluids
2001 Sauer-Danfoss
Sauer-Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Sauer -Danfoss reserves the right
to alter its products without prior notice. This also applies to products already ordered provided that such alterations can be made without subsequent
changes being necessary in specifications already agreed. All trademarks in this material are properties of the respective companies. Sauer-Danfoss
and the Sauer-Danfoss logotype are trademarks of the Sauer-Danfoss Group. All rights reserved.
Frontpage: P300039.TIF. P300046.TIF, P300023.TIF, P300040.TIF, P300047.TIF, Drawing 151-1837
DKMH.PK.110.B5.02 520L0262
Planetary gears
Sauer-Danfoss complements the motor range with a complete programme of planetary
gears adapted to suit. The combination of motors and gears makes it possible to obtain
smooth running at fractional speeds and with torques up to 650.000 Nm [5.800.000 lbfin].
The SauerDanfoss LSHT motors are used in the following application areas:
SURVEY OF LITERATURE
WITH TECHNICAL DATA
ON SAUER-DANFOSS
HYDRAULIC MOTORS
Construction equipment
Agricultural equipment
Material handling & Lifting equipment
Forestry equipment
Lawn and turf equipment
Special purpose
Machine tools and stationary equipment
Marine equipment
Detailed data on all Sauer-Danfoss motors can be found in our motor catalogue, which is
divided into 5 individual subcatalogues:
General information on Sauer-Danfoss hydraulic motors: function, use, selection of
hydraulic motor, hydraulic systems, etc.
Technical data on small motors: OML and OMM
Technical data on medium sized motors: OMP, OMR, OMH and OMEW
Technical data on medium sized motors: DH and DS
Technical data on large motors: OMS, OMT and OMV
Technical data on large motors: TMT
A general survey brochure on Sauer-Danfoss hydraulic motors gives a quick motor
reference based on power, torque, speed and capabilities.
DKMH.PK.110.B5.02 520L0262
Page
OMP, OMR, OMH and OMEW.......................................................................................................................................6
Speed, torque and output ..........................................................................................................................................6
OMP ........................................................................................................................................................................................8
Version....................................................................................................................................................................................8
Code number.......................................................................................................................................................................9
Technical data...........................................................................................................................................................10-26
Technical data (e.g. speed, torque, pressure etc.) ......................................................................................10-12
Max. permissisble shaft seal pressure.................................................................................................................. 13
Pressure drop in motor, oil flow in drain line, direction of shaft rotation ............................................... 14
Permissible shaft loads .......................................................................................................................................15-17
Function diagrams ...............................................................................................................................................18-23
Shaft version...........................................................................................................................................................24-25
Port thread versions................................................................................................................................................... 26
Dimensions ...................................................................................................................................................................... 27
Dimensions .............................................................................................................................................................27-35
OMR ..................................................................................................................................................................................... 36
Version................................................................................................................................................................................. 36
Code number.................................................................................................................................................................... 37
Technical data...........................................................................................................................................................38-54
Technical data (e.g. speed, torque, pressure etc.) .....................................................................................38-40
Max. permissisble shaft seal pressure.................................................................................................................. 41
Pressure drop in motor, oil flow in drain line, direction of shaft rotation ............................................... 42
Permissible shaft loads .......................................................................................................................................43-44
Function diagrams ...............................................................................................................................................45-49
Shaft version...........................................................................................................................................................50-53
Port thread versions................................................................................................................................................... 54
Dimensions ...................................................................................................................................................................... 55
Dimensions .............................................................................................................................................................55-65
OMH..................................................................................................................................................................................... 66
Version................................................................................................................................................................................. 66
Code number.................................................................................................................................................................... 67
Technical data...........................................................................................................................................................68-80
Technical data (e.g. speed, torque, pressure etc.) .....................................................................................68-70
Max. permissisble shaft seal pressure.................................................................................................................. 71
Pressure drop in motor, oil flow in drain line, direction of shaft rotation ............................................... 72
Permissible shaft loads ............................................................................................................................................. 73
Function diagrams ...............................................................................................................................................74-76
Shaft version...........................................................................................................................................................77-79
Port thread versions................................................................................................................................................... 80
Dimensions ...................................................................................................................................................................... 81
Dimensions .............................................................................................................................................................81-82
DKMH.PK.110.B5.02 520L0262
Page
OMEW ................................................................................................................................................................................. 84
Version................................................................................................................................................................................. 84
Code number.................................................................................................................................................................... 85
Technical data...........................................................................................................................................................86-94
Technical data (e.g. speed, torque, pressure etc.) ........................................................................................... 86
Max. permissisble shaft seal pressure.................................................................................................................. 87
Pressure drop in motor, direction of shaft rotation ........................................................................................ 88
Permissible shaft loads ............................................................................................................................................. 89
Function diagrams ...............................................................................................................................................90-92
Shaft version................................................................................................................................................................. 93
Port thread versions................................................................................................................................................... 94
Dimensions ...................................................................................................................................................................... 95
Dimensions .............................................................................................................................................................95-96
DKMH.PK.110.B5.02 520L0262
Max. speed
min -1
(rpm)
1800
1600
1400
1200
1000
800
600
400
315
250
200
160
125
100
3)
3)
500
400
3)
250
3)
3)
315
200
250
250
375 2)
200
315 2)
200
250 2)
2)
200 2)
125
160 2)
80
100
1)
1)
50
400
315
1)
1)
250
160
200
125
80
100
50
32
Max. Torque
Nm
10000
2)
lbf.in
40
25
200
1100
9000
1000
8000
900
7000
800
6000
700
600
5000
500
4000
400
3000
300
2000
200
1000
250
315
250
315
160
160
200
125
125
200
100
100
3)
500
2)
2)
3)
400
315
315
375
250
200
2)
125
160
80
100
50
1)
400
315
1)
1)
250
1)
200
160
125
100
80
50
40
32
25
100
Max. output
25
hp
kW
15
20
15
10
10
Peak values
OMR
Intermittend values
OMH
3)
500
3)
400
315
2)
375
315
2)
2)
2)
250
200
2)
125
OMP
160
80
100
50
1)
400
315
1)
1)
250
200
160
125
100
50
80
40
32
25
1)
OMEW
Continuous values
151-1418.10
1) 1 /4 in shaft
2) 11/4 in or 11/4 in tapered shaft
3) 11/4 in splined shaft
1
DKMH.PK.110.B5.02 520L0262
The bar diagrams above are useful for a quick selection of relevant motor size for the
application. The final motor size can be determined by using the function diagram for
each motor size.
The function diagrams are based on actual tests on a representative number of motors
from our production. The diagrams apply to a return pressure between 5 and 10 bar
[75 and 150 psi] when using mineral based hydraulic oil with a viscosity of 35 mm2/s
[165 SUS] and a temperature of 50C [120F]. For further explanation concerning how to
read and use the function diagrams, please consult the paragraph "Selection of motor
size" in the technical information "General" DHMH.PK.100.G2.02 520L0232.
DKMH.PK.110.B5.02 520L0262
OMP
Technical Information
Versions
Cyl. 1 in
Splined 1 in
4 hole oval
flange
(A4 flange)
Square
flange
(C-flange)
Wheel
Cyl. 32 mm
Cyl. 25 mm
Cyl. 25 mm
Tap. 28.5 mm
OMP
OMP
OMP
OMP
OMP
Yes
Yes
OMP
X
X
X
X
X
Yes
Yes
Yes
Yes
Yes
X
X
X
X
X
X
X
G 1/2
G 1/2
/8 - 14 UNF
1
/2 - 14 NPTF
G 1/2
G 1/2
X
X
X
X
X
X
X
X
X
X
X
X
X
DKMH.PK.110.B5.02 520L0262
X
X
No
No
Yes
No
No
X
X
Specials
No
Yes
Yes
No
Yes
X
X
G 1/2
7
/8 - 14 UNF
G 1/2
G 1/2
US version
European version
No
No
Yes
Yes
X
X
X
Specials:
A : Corrosion resistant parts
B : With needle bearings
No
Yes
Yes
Yes
X
X
X
X
Cyl. 1 in
Check valve
2 hole oval
flange
G 1/2
G 1/2
G 1/2
G 1/2
G 1/2
Drain connection
Cyl. 25 mm
(A2-flange)
Port size
Shaft
Mounting flange
VERSIONS
OMP
OMP
OMP C
OMP
Yes
OMP
Yes
OMP
Yes
OMP
Yes
OMPW
Yes
B
OMPW N
Function diagram see page :
OMP
Technical Information
Code Numbers
CODE NUMBERS
32
40
50
80
100
125
160
200
250
315
400
Dimensions Page
151151151151151151151-
0340
0640
7080
0341
0641
7081
0342
0642
7082
0310
0610
1208
5191
0300
0600
7041
0311
0611
1209
5192
0301
0601
7042
0312
0612
1210
5193
0302
0602
7043
0313
0613
1217
5194
0303
0603
70441)
0314
0614
1211
5195
0304
0604
0315
0615
1212
5196
0305
0605
0316
0616
1213
5197
0306
0606
0317
0617
1214
5198
0307
0607
0318
0618
1215
5199
0308
0608
10
10
10
10
10
10
27
28
29
30
27
28
151151-
0330
0630
0331
0631
0332
0632
0333
0633
7045
0334
0634
7046
0335
0635
7047
0336
0636
7048
0337
0637
7049
0338
0638
10
11
11
31
27
28
151-
5001
5002
5003
5004
5005
5006
5007
5008
5009
12
32
151151151151151-
18
18
19
5211
7061
7021
7101
5301
19
5212
7062
7022
7102
5302
20
5213
7063
7023
7103
5303
20
5214
5174
7024
7104
5304
21
5215
7065
7025
7105
5305
21
5216
7066
7026
7106
5306
22
5217
7067
7027
7107
5307
22
5218
7068
7028
7108
5308
23
5219
7069
7029
7109
5309
23
10
10
10
10
11
33
34
34
35
35
CODE NUMBERS
25
DISPLACEMENT [cm3]
Ordering
Add the four digit prefix 151- to the four digit numbers from the chart for complete
code number.
Example:
151-0305 for an OMP 200 with A2 flange, cyl. 1 in shaft, port size G 1/2 and high pressure
shaft seal.
Note: Orders will not be accepted without the four digit prefix.
DKMH.PK.110.B5.02 520L0262
OMP
Technical Information
Technical data
TECHNICAL DATA FOR OMP/OMPW WITH 25 MM AND 1 IN CYLINDRICAL SHAFT
Type
Motor size
Geometric displacement
Max. speed
OMP OMP OMP OMP OMP OMP OMP OMP OMP OMP
25
32
40
50
80
100 125 160 200 250
OMP OMP
315 400
25.0
[1.53]
1600
1800
33
[290]
47
[420]
67
[590]
4.5
[6.0]
32.0
[1.96]
1560
1720
43
[380]
61
[540]
86
[760]
5.8
[7.8]
40.0
48.6
77.8
97.3
[2.45] [2.97] [4.76] [5.95]
1500 1230
770
615
1750 1540
960
770
52
93
150
190
[460] [820] [1330] [1680]
74
120
190
230
[660] [1060] [1680] [2040]
107
140
220
270
[950] [1240] [1950] [2390]
7.0
10.0
10.0
11.0
[9.4] [13.4] [13.4] [14.8]
125.0
[7.65]
480
600
240
[2120]
290
[2570]
370
[3280]
10.0
[13.4]
155.7
[9.53]
385
480
300
[2660]
370
[3280]
430
[3810]
10.0
[13.4]
194.6
[11.91]
310
385
300
[2660]
380
[3360]
540
[4780]
8.0
[10.7]
242.3
[14.83]
250
310
300
[2660]
410
[3630]
550
[4870]
6.0
[8.1]
306.1
[18.73]
195
245
300
[2660]
390
[3450]
600
[5310]
5.0
[6.7]
389.2
[23.82]
155
190
300
[2660]
420
[3720]
600
[5310]
4.0
[5.4]
6.1
[8.2]
100
cont.
[1450]
bar
140
int.1)
[psi]
[2030]
225
peak2)
[3260]
40
cont.
l/min
[10.6]
[USgal/min]
45
int.1)
[11.9]
bar
10
[psi]
[145]
at max. press. drop cont. 30
Nm [lbfin]
[270]
at max. press. drop int. 1) 40
Nm [lbfin]
[350]
min-1
20
[rpm]
7.8
[10.5]
100
[1450]
140
[2030]
225
[3260]
50
[13.2]
55
[14.5]
10
[145]
40
[350]
55
[490]
10.6
[14.2]
100
[1450]
140
[2030]
225
[3260]
60
[15.9]
70
[18.5]
10
[145]
45
[400]
63
[560]
12.0
[16.1]
140
[2030]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
10
[145]
80
[710]
100
[890]
12.0
[16.1]
140
[2030]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
10
[145]
135
[1200]
170
[1510]
13.0
[17.4]
140
[2030]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
10
[145]
170
[1510]
210
[1860]
12.0
[16.1]
140
[2030]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
9
[130]
210
[1860]
270
[2390]
12.0
[16.1]
140
[2030]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
7
[100]
280
[2480]
350
[3100]
11.0
[14.8]
115
[1670]
150
[2180]
225
[3260]
60
[15.9]
75
[19.8]
5
[75]
270
[2390]
360
[3190]
9.0
[12.1]
90
[1310]
125
[1810]
180
[2610]
60
[15.9]
75
[19.8]
5
[75]
280
[2480]
390
[3450]
7.0
[9.4]
75
[1090]
100
[1450]
160
[2320]
60
[15.9]
75
[19.8]
5
[75]
280
[2480]
370
[3280]
6.0
[8.1]
60
[870]
80
[1160]
130
[1890]
60
[15.9]
75
[19.8]
5
[75]
280
[2480]
400
[3540]
15
10
10
10
cm3
[in3]
min-1
[rpm]
cont.
int1)
cont.
Max. torque
Nm
[lbfin]
int.1)
peak2)
Max. output
Min. speed3)
kW
[hp]
cont.
int.1)
1)
Intermittent operation: the permissible values may occur for max. 10% of every minute.
Peak load: the permissible values may occur for max. 1% of every minute.
3)
Operation at lower speeds may be slightly less smooth.
2)
10
DKMH.PK.110.B5.02 520L0262
OMP
Technical Information
Technical data
TECHNICAL DATA FOR OMP/OMPW WITH 1 IN SPLINED AND 28,5 MM TAPERED SHAFT
Type
Motor size
Geometric displacement
Max. speed
OMP
50
OMP
80
OMP
100
OMP
125
OMP
160
OMP
200
OMP
250
OMP
315
OMP
400
48.6
[2.97]
1230
1540
93
[820]
120
[1060]
140
[1240]
10.0
[13.4]
77.8
[4.76]
770
960
150
[1330]
190
[1680]
220
[1950]
10.0
[13.4]
97.3
[5.95]
615
770
190
[1680]
230
[2040]
270
[2390]
11.0
[14.8]
125.0
[7.65]
480
600
240
[2120]
290
[2570]
370
[3280]
10.0
[13.4]
155.7
[9.53]
385
480
300
[2660]
370
[3280]
430
[3810]
10.0
[13.4]
194.6
[11.91]
310
385
360
[3190]
450
[3980]
540
[4780]
10.0
[13.4]
242.3
[14.83]
250
310
360
[3190]
460
[4070]
550
[4870]
8.0
[10.7]
306.1
[18.73]
195
245
360
[3190]
470
[4160]
540
[4780]
6.0
[8.0]
389.2
[23.82]
155
190
360
[3190]
460
[4070]
560
[4960]
5.0
[6.7]
12.0
[16.1]
140
cont.
[2030]
bar
175
int.1)
[psi]
[2540]
225
peak2)
[3260]
60
cont.
l/min
[15.9]
[USgal/min]
75
int.1)
[19.8]
bar
10
[psi]
[145]
at max. press. drop cont.
80
Nm [lbfin]
[710]
at max. press. drop int.1)
100
Nm [lbfin]
[890]
min-1
10
[rpm]
12.0
[16.1]
140
[2030]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
10
[145]
135
[1200]
170
[1510]
13.0
[17.4]
140
[2030]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
10
[145]
170
[1510]
210
[1860]
12.0
[16.1]
140
[2030]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
9
[130]
210
[1860]
270
[2390]
12.0
[16.1]
140
[2030]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
7
[100]
280
[2480]
350
[3100]
12.0
[16.1]
140
[2030]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
5
[75]
340
[3010]
420
[3720]
10.5
[14.1]
105
[1520]
140
[2030]
180
[2610]
60
[15.9]
75
[19.8]
5
[75]
330
[2920]
440
[3890]
7.5
[10.1]
90
[1310]
120
[1740]
160
[2320]
60
[15.9]
75
[19.8]
5
[75]
340
[3010]
450
[3980]
6.0
[8.0]
70
[1020]
90
[1310]
130
[1890]
60
[15.9]
75
[19.8]
5
[75]
345
[3050]
425
[3760]
10
cm3
[in3]
min-1
[rpm]
cont.
int1)
cont.
Max. torque
Nm
[lbfin]
int.1)
peak2)
Max. output
Min. speed3)
1)
2)
3)
kW
[hp]
cont.
int.1)
Intermittent operation: the permissible values may occur for max. 10% of every minute.
Peak load: the permissible values may occur for max. 1% of every minute.
Operation at lower speeds may be slightly less smooth.
DKMH.PK.110.B5.02 520L0262
11
OMP
Technical Information
Technical data
TECHNICAL DATA FOR OMP/OMPW WITH 32 MM CYLINDRICAL SHAFT
Type
Motor size
Geometric displacement
Max. speed
OMP
50
OMP
80
OMP
100
OMP
125
OMP
160
OMP
200
OMP
250
OMP
315
OMP
400
48.6
[2.97]
1230
1540
93
[820]
120
[1060]
140
[1240]
10.0
[13.4]
77.8
[4.76]
770
960
150
[1330]
190
[1680]
220
[1950]
10.0
[13.4]
97.3
[5.95]
615
770
190
[1680]
230
[2040]
270
[2390]
11.0
[14.8]
125.0
[7.65]
480
600
240
[2120]
290
[2570]
370
[3280]
10.0
[13.4]
155.7
[9.53]
385
480
300
[2660]
370
[3280]
430
[3810]
10.0
[13.4]
194.6
[11.91]
310
385
360
[3190]
450
[3980]
540
[4780]
10.0
[13.4]
242.3
[14.83]
250
310
460
[4070]
570
[5050]
670
[5930]
9.5
[12.7]
306.1
[18.73]
195
245
470
[4160]
620
[5490]
820
[7260]
7.5
[10.1]
389.2
[23.82]
155
190
490
[4340]
630
[5580]
840
[7440]
6.5
[8.7]
12.0
[16.1]
140
cont.
[2030]
bar
175
int.1)
[psi]
[2540]
225
peak2)
[3260]
60
cont.
l/min
[15.9]
[USgal/min]
75
int.1)
[19.8]
bar
10
[psi]
[145]
at max. press. drop cont.
80
Nm [lbfin]
[710]
at max. press. drop int.1)
100
Nm [lbfin]
[890]
min-1
10
[rpm]
12.0
[16.1]
140
[2030]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
10
[145]
135
[1200]
170
[1510]
13.0
[17.4]
140
[2030]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
10
[145]
170
[1510]
210
[1860]
12.0
[16.1]
140
[2030]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
9
[130]
210
[1860]
270
[2390]
12.0
[16.1]
140
[2030]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
7
[100]
280
[2480]
350
[3100]
12.0
[16.1]
140
[2030]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
5
[75]
340
[3010]
420
[3720]
12.0
[16.1]
140
[2030]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
5
[75]
420
[3720]
530
[4690]
9.0
[12.1]
120
[1741]
160
[2320]
225
[3260]
60
[15.9]
75
[19.8]
5
[75]
460
[4070]
600
[5310]
7.5
[10.1]
95
[1380]
125
[1810]
180
[2610]
60
[15.9]
75
[19.8]
5
[75]
460
[4070]
600
[5310]
10
cm3
[in3]
min-1
[rpm]
cont.
int1)
cont.
Max. torque
Nm
[lbfin]
int.1)
peak2)
Max. output
Min. speed3)
kW
[hp]
cont.
int.1)
Type
OMP 25 - 400
bar
[psi]
bar
[psi]
bar
[psi]
1)
175
[2540]
200
[2900]
225
[3260]
175
[2540]
200
[2900]
225
[3260]
cont.
int.1]
peak2]
Intermittent operation: the permissible values may occur for max. 10% of every minute.
Peak load: the permissible values may occur for max. 1% of every minute.
3)
Operation at lower speeds may be slightly less smooth.
2)
12
DKMH.PK.110.B5.02 520L0262
OMP
Technical Information
Technical data max. permissible shaft seal pressure
OMP WITH HIGH
PRESSURE SHAFT SEAL
(HPS)
Max. return pressure without drain line or max. pressure in the drain line
1)
Intermittent operation: the permissible values may occur for max. 10% of every minute.
DKMH.PK.110.B5.02 520L0262
13
OMP
Technical Information
Technical data
PRESSURE DROP IN
MOTOR
The curve applies to an unloaded motor shaft and an oil viscosity of 35 mm2/s [165 SUS]
A: OMP 50 - 400
B: OMP 25 - 40 / OMPW
Pressure
drop
bar
[psi]
100
[1450]
140
[2030]
DIRECTION OF SHAFT
ROTATION
14
DKMH.PK.110.B5.02 520L0262
Viscosity
mm2/s
[SUS]
Oil flow in
drain line
l/min
[US gal/min]
20
[100]
35
[165]
20
[100]
35
[165]
2.5
[0.66]
1.8
[0.78]
3.5
[0.93]
2.8
[0.74]
OMP
Technical Information
Technical data
PERMISSIBLE SHAFT
LOADS FOR OMP
Shaft version
Permissible
shaft load (PR) l in mm
Permissible
shaft load (PR) l in inch
Square flange**
2-hole oval flange
(US version)
25 mm cylindrical shaft
1 in cylindrical shaft
1 in splined shaft
32 mm cylindrical shaft
25 mm cylindrical shaft
800 250000 N*
n
95 + l
800 187500 N*
n
95 + l
800 250000 N*
n
101 + l
DKMH.PK.110.B5.02 520L0262
15
OMP
Technical Information
Technical data
PERMISSIBLE SHAFT
LOAD FOR OMPW WITH
SLIDE BEARINGS
A:
B:
C:
D:
The output shaft on OMPW can be offered in slide bearings similar to the other OMPmotors. The permissible higher radial load is therefore due to the recessed mounting
flange moving the point of load closer to the motor bearings.
The permissible radial load on the shaft is shown for different speeds as a function of the
distance from the mounting flange to the point of load application.
The curves are not based on calculations of B10 bearing life. They represent absolute
limits that must not be exceeded.
Curve A indicates the max. radial shaft load. Any shaft load exceeding the values quoted
in curve A will involve risk of breakage.
16
DKMH.PK.110.B5.02 520L0262
OMP
Technical Information
Technical data
PERMISSIBLE SHAFT
LOAD FOR OMPW N WITH
NEEDLE BEARING
A:
B:
C:
D:
The output shaft on OMPW N can be offered in needle bearings. These bearings and
the recessed mounting flange allow a higher permissible radial load in comparison to
OMP motors.
The permissible radial load on the shaft is shown for different speeds as a function of the
distance from the mounting flange to the point of load application.
Curve A indicates the max. radial shaft load. Any shaft load exceeding the values quoted
in curve A will involve risk of breakage.
The other curves apply to a B10 bearing life of 2000 hours at the number of revolutions
indicated by the curve letter. Mineral based hydraulic oil with a sufficient content of
anti-wear additives must be used.
Bearing life calculations can be made using the explanation and formula provided
in the chapter "Bearing dimensioning" in the technical information "General"
DHMH.PK.100.G2.02 520L0232.
DKMH.PK.110.B5.02 520L0262
17
OMP
Technical Information
Function diagrams
FUNCTION DIAGRAMS
Explanation of function diagram use, basis and conditions can be found on page 7.
A: Continuous range
B: Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent pressure drop for the actual shaft version can
be found on page 10-12.
Note: Intermittent pressure drop and oil flow must not occur simultaneously.
18
DKMH.PK.110.B5.02 520L0262
OMP
Technical Information
Function diagrams
FUNCTION DIAGRAMS
Explanation of function diagram use, basis and conditions can be found on page 7.
A: Continuous range
B: Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent pressure drop for the actual shaft version can
be found on page 10-12.
Note: Intermittent pressure drop and oil flow must not occur simultaneously.
DKMH.PK.110.B5.02 520L0262
19
OMP
Technical Information
Function diagrams
FUNCTION DIAGRAMS
Explanation of function diagram use, basis and conditions can be found on page 7.
A: Continuous range
B: Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent pressure drop for the actual shaft version can
be found on page 10-12.
Note: Intermittent pressure drop and oil flow must not occur simultaneously.
20
DKMH.PK.110.B5.02 520L0262
OMP
Technical Information
Function diagrams
FUNCTION DIAGRAMS
Explanation of function diagram use, basis and conditions can be found on page 7.
A: Continuous range
B: Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent pressure drop for the actual shaft version can
be found on page 10-12.
Note: Intermittent pressure drop and oil flow must not occur simultaneously.
DKMH.PK.110.B5.02 520L0262
21
OMP
Technical Information
Function diagrams
FUNCTION DIAGRAMS
Explanation of function diagram use, basis and conditions can be found on page 7.
A: Continuous range
B: Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent pressure drop for the actual shaft version can
be found on page 10-12.
Note: Intermittent pressure drop and oil flow must not occur simultaneously.
22
DKMH.PK.110.B5.02 520L0262
OMP
Technical Information
Function diagrams
FUNCTION DIAGRAMS
Explanation of function diagram use, basis and conditions can be found on page 7.
A: Continuous range
B: Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent pressure drop for the actual shaft version can
be found on page 10-12.
Note: Intermittent pressure drop and oil flow must not occur simultaneously.
DKMH.PK.110.B5.02 520L0262
23
OMP
Technical Information
Shaft version
SHAFT VERSION
A: Cylindrical shaft
25 mm
D: Parallel key
A8 7 32
DIN 6885
B: Cylindrical shaft
1 in
E: Parallel key
1
/4 1/4 11/4 in
B.S. 46
US version
C: Cylindrical shaft
1 in
F: Parallel key
1
/4 1/4 11/4 in
B.S. 46
151-1842.11
24
DKMH.PK.110.B5.02 520L0262
OMP
Technical Information
Shaft version
SHAFT VERSION
D: Cylindrical shaft
32 mm
I: Parallel key
A10 8 45
DIN 6885
E: Splined shaft
B.S. 2059 (SAE 6 B)
Straight-sided,
bottom fitting, dep.
Fit 2
Nom. size 1 in
* Deviates from
BS 2059 (SAE 6B)
F: Tapered shaft
(ISO/R775)
H: DIN 937
NV 30
Tightening torque:
100 10 Nm
G: Taper 1:10
J: Parallel key
B5 5 14
DIN 6885
DKMH.PK.110.B5.02 520L0262
25
OMP
Technical Information
Technical data
PORT THREAD VERSIONS
A: G main ports
G: ISO 228/1 - G1/2
151-1844.10
D: G drain port
E: ISO 228/1 - G1/4
26
DKMH.PK.110.B5.02 520L0262
OMP
Technical Information
Dimensions European version
DIMENSIONS
Type
OMP 25
OMP 32
OMP 40
OMP 50
OMP 80
OMP 100
OMP 125
OMP 160
OMP 200
OMP 250
OMP 315
OMP 400
mm mm
L
[in] 1 [in]
129.0
[5.08]
130.0
[5.12]
131.0
[5.16]
131.0
[5.16]
135.0
[5.31]
137.5
[5.41]
141.0
[5.55]
145.5
[5.73]
150.5
[5.93]
157.0
[6.18]
165.5
[6.52]
176.6
[6.95]
4.1
[0.16]
5.2
[0.20]
6.5
[0.26]
6.5
[0.26]
10.4
[0.41]
13.0
[0.51]
16.7
[0.66]
20.8
[0.82]
26.0
[1.02]
32.5
[1.28]
40.9
[1.61]
52.0
[2.05]
DKMH.PK.110.B5.02 520L0262
27
OMP
Technical Information
Dimensions European version
DIMENSIONS
Type
OMP 25
OMP 32
OMP 40
OMP 50
OMP 80
OMP 100
OMP 125
OMP 160
OMP 200
OMP 250
OMP 315
OMP 400
mm mm
L
[in] 1 [in]
129.0
[5.08]
130.0
[5.12]
131.0
[5.16]
131.0
[5.16]
135.0
[5.31]
137.5
[5.41]
141.0
[5.55]
145.5
[5.73]
150.5
[5.93]
157.0
[6.18]
165.5
[6.52]
176.6
[6.95]
4.1
[0.16]
5.2
[0.20]
6.5
[0.26]
6.5
[0.26]
10.4
[0.41]
13.0
[0.51]
16.7
[0.66]
20.8
[0.82]
26.0
[1.02]
32.5
[1.28]
40.9
[1.61]
52.0
[2.05]
C: Drain connection
G 14; 12 mm [0.47 in] deep
D: G 12; 15 mm [0.59 in] deep
E: M8; 13 mm [0.51 in] deep
(4 pcs.)
28
DKMH.PK.110.B5.02 520L0262
OMP
Technical Information
Dimensions European version
DIMENSIONS
Type
OMP 50
OMP 80
OMP 100
OMP 125
OMP 160
OMP 200
OMP 250
OMP 315
OMP 400
OMP C
Side port version with 2 hole oval mounting flange (A2-flange).
mm mm
L
[in] 1 [in]
131.0
[5.16]
135.0
[5.31]
137.5
[5.41]
141.0
[5.55]
145.5
[5.73]
150.5
[5.93]
157.0
[6.18]
165.5
[6.52]
176.6
[6.95]
6.5
[0.26]
10.4
[0.41]
13.0
[0.51]
16.7
[0.66]
20.8
[0.82]
26.0
[1.02]
32.5
[1.28]
40.9
[1.61]
52.0
[2.05]
C: Drain connection
G 14; 12 mm [0.47 in] deep
D: G 12; 15 mm [0.59 in] deep
E: M8; 13 mm [0.51 in] deep
(4 pcs.)
DKMH.PK.110.B5.02 520L0262
29
OMP
Technical Information
Dimensions European version
DIMENSIONS
Type
OMP 50
OMP 80
OMP 100
OMP 125
OMP 160
OMP 200
OMP 250
OMP 315
OMP 400
mm mm
L
[in] 1 [in]
145.1
[5.71]
149.0
[5.87]
151.7
[5.97]
155.2
[6.11]
159.4
[6.28]
164.6
[6.48]
171.1
[6.74]
179.5
[7.07]
190.6
[7.50]
6.5
[0.26]
10.4
[0.41]
13.0
[0.51]
16.3
[0.66]
20.8
[0.82]
26.0
[1.02]
32.5
[1.28]
40.9
[1.61]
52.0
[2.05]
C: Drain connection
G 14; 12 mm [0.47 in] deep
D: G 12; 15 mm [0.59 in] deep
30
DKMH.PK.110.B5.02 520L0262
OMP
Technical Information
Dimensions US version
DIMENSIONS
Type
OMP 25
OMP 32
OMP 40
OMP 50
OMP 80
OMP 100
OMP 125
OMP 160
OMP 200
OMP 250
OMP 315
OMP 400
mm mm
L
[in] 1 [in]
135.0
[5.31]
136.0
[5.35]
137.0
[5.39]
137.0
[5.39]
141.0
[5.55]
143.5
[5.65]
147.0
[5.79]
151.5
[5.96]
156.5
[6.16]
163.0
[6.42]
171.5
[6.75]
182.6
[7.19]
4.1
[0.16]
5.2
[0.20]
6.5
[0.26]
6.5
[0.26]
10.4
[0.41]
13.0
[0.51]
16.7
[0.66]
20.8
[0.82]
26.0
[1.02]
32.5
[1.28]
40.9
[1.61]
52.0
[2.05]
C: Drain connection
7
16 - 20 UNF;
12 mm [0.47 in] deep
D: 78 - 14 UNF;
16.7 mm [0.66 in] deep
or 12 - 14 NPTF
E: M8; 13 mm [0.51 in] deep
(4-off )
DKMH.PK.110.B5.02 520L0262
31
OMP
Technical Information
Dimensions European version
DIMENSIONS
Type
OMP 50
OMP 80
OMP 100
OMP 125
OMP 160
OMP 200
OMP 250
OMP 315
OMP 400
mm mm
L
[in] 1 [in]
131.0
[5.16]
135.0
[5.31]
137.5
[5.41]
141.0
[5.55]
145.5
[5.73]
150.5
[5.93]
157.0
[6.18]
165.5
[6.52]
176.6
[6.95]
6.5
[0.26]
10.4
[0.41]
13.0
[0.51]
16.7
[0.66]
20.8
[0.82]
26.0
[1.02]
32.5
[1.28]
40.9
[1.61]
52.0
[2.05]
C: Drain connection
G 14; 12 mm [0.47 in] deep
D: G 12; 15 mm [0.59 in] deep
E: M8; 13 mm [0.51 in] deep
(4 pcs.)
32
DKMH.PK.110.B5.02 520L0262
OMP
Technical Information
Dimensions European version
DIMENSIONS
Type
OMP 50
OMP 80
OMP 100
OMP 125
OMP 160
OMP 200
OMP 250
OMP 315
OMP 400
mm mm
L
[in] 1 [in]
151.1
[5.94]
155.0
[6.10]
157.6
[6.20]
161.1
[6.34]
165.4
[6.51]
170.6
[6.72]
177.1
[6.97]
185.5
[7.30]
196.6
[7.74]
6.5
[0.26]
10.4
[0.41]
13.0
[0.51]
16.7
[0.66]
20.8
[0.82]
26.0
[1.02]
32.5
[1.28]
40.9
[1.61]
52.0
[2.05]
C: Drain connection
G 14; 12 mm [0.47 in] deep
D: G 12; 15 mm [0.59 in] deep
E: M10; 15 mm [0.59 in] deep
(4 pcs.)
DKMH.PK.110.B5.02 520L0262
33
OMP
Technical Information
Dimensions US version
DIMENSIONS
Type
OMP 50
OMP 80
OMP 100
OMP 125
OMP 160
OMP 200
OMP 250
OMP 315
OMP 400
mm mm
L
[in] 1 [in]
131.0
[5.16]
135.0
[5.31]
137.5
[5.41]
141.0
[5.55]
145.5
[5.73]
150.5
[5.93]
157.0
[6.18]
165.5
[6.52]
176.6
[6.95]
6.5
[0.26]
10.4
[0.41]
13.0
[0.51]
16.7
[0.66]
20.8
[0.82]
26.0
[1.02]
32.5
[1.28]
40.9
[1.61]
52.0
[2.05]
C: Drain connection
7
16 - 20 UNF;
11.94 mm [0.47 in] deep
D: 78 - 14 UNF;
16.76 mm [0.66 in] deep
or 12 - 14 NPTF
E: 38 - 16 UNC;
14.97 mm [0.59 in] deep
(4-off )
F: M8; 12.95 mm [0.51 in] deep
(4-off )
34
DKMH.PK.110.B5.02 520L0262
OMP
Technical Information
Dimensions European version
DIMENSIONS
OMPW
OMPW N
mm
[in]
Type
L2
OMPW with
25 mm shaft
OMPW N
with tapered shaft
115.0
[4.53]
116.0
[4.57]
Type
OMP 50
OMP 80
OMP 100
OMP 125
OMP 160
OMP 200
OMP 250
OMP 315
OMP 400
mm mm
L
[in] 1 [in]
70.8
[2.78]
74.7
[2.97]
77.3
[3.04]
80.6
[3.17]
85.1
[3.35]
90.3
[3.56]
96.8
[3.81]
105.2
[4.14]
116.3
[4.58]
6.5
[0.26]
10.4
[0.41]
13.0
[0.51]
16.7
[0.66]
20.8
[0.82]
26.0
[1.02]
32.5
[1.28]
40.9
[1.61]
52.0
[2.05]
C: Drain connection
G 14; 12 mm [0.47 in] deep
D: G 12; 15 mm [0.59 in] deep
E: M10; 20 mm [0.79 in] deep
(4 pcs.)
DKMH.PK.110.B5.02 520L0262
35
OMR
Technical Information
Versions
Splined 1 in
4 hole oval
flange
Cyl. 32 mm
Tap. 28.5 mm
Cyl. 25 mm
Cyl. 32 mm
(A4-flange)
Cyl. 1 1/4 in
Square flange Cyl. 25 mm
(C-flange)
Cyl. 1 in
Tap. 35 mm
Wheel
Tap. 1 1/4 in
G 1/2
7
/8 - 14 UNF
G 1/2
G 1/2
7
/8 - 14 UNF
G 1/2
G 1/2
G 1/2
G 1/2
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
DKMH.PK.110.B5.02 520L0262
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
No
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Specials
X
X
X
X
X
Specials:
A : Corrosion resistant parts
B : With needle bearings
36
/8 - 14 UNF
G 1/2
7
/8 - 14 UNF
G 1/2
7
/8 - 14 UNF
US version
European version
X
X
X
X
Check valve
Cyl 1 in
G 1/2
G 1/2
G 1/2
G 1/2
G 1/2
Drain connection
Cyl. 25 mm
2 hole oval
flange
(A2-flange)
Port size
Shaft
Mounting flange
VERSIONS
OMR
OMR
OMR C
OMR
OMR
OMR
OMR
OMR
OMR
OMR
OMR
OMR
OMR
Yes
Yes
OMR
Yes
Yes
OMR
Yes
Yes
OMR
Yes
Yes
OMR
Yes
Yes
B
OMRW N
Yes
Yes
B
OMRW N
Function diagram see page :
OMR
Technical Information
Code Numbers
CODE NUMBERS
50
80
100
125
160
200
250
315
375
0410
0710
1231
6190
0400
0700
7240
0420
0720
7250
0248
0265
6010
6000
6110
6210
7260
6300
6430
0411
0711
1232
6191
0401
0701
7241
0421
0721
7251
0242
0266
6011
6001
6111
6211
7261
6301
6431
0412
0712
1233
6192
0402
0702
7242
0422
0722
7252
0243
0267
6012
6002
6112
6212
7262
6302
6432
0413
0713
1238
6193
0403
0703
7243
0423
0723
7253
0208
6295
6013
6003
6113
6213
7263
6303
6433
0414
0714
1234
6194
0404
0704
7244
0424
0724
7254
0244
0268
6014
6004
6114
6214
7264
6304
6434
0415
0715
1235
6195
0405
0705
7245
0425
0725
7255
0245
0269
6015
6005
6115
6215
7265
6305
6435
0416
0716
1236
6196
0406
0706
7246
0426
0726
7256
0247
0271
6016
6006
6116
6216
7266
6306
6436
0417
0717
1237
6197
0407
0707
7247
0427
0727
7257
0246
0270
6017
6007
6117
6217
7267
6307
6437
0418
0718
1243
6198
0408
0708
7248
0428
0728
7258
6294
6296
6018
6008
6118
6218
7269
6308
6438
45
45
46
46
47
47
48
48
49
Dimensions Page
151151151151151151151151151151151151151151151151151151151-
CODE NUMBERS
DISPLACEMENT [cm3]
38
38
38
38
38
38
38
39
39
39
40
39
38
40
40
38
38
40
40
55
56
57
58
55
56
59
55
56
59
57
57
60
60
61
62
63
64
65
Ordering
Add the four digit prefix 151- to the four digit numbers from the chart for complete
code number.
Example:
151-6004 for an OMR 160 with A4 flange, cyl. 32 mm shaft, port size G 1/2 and side port
version.
Note: Orders will not be accepted without the four digit prefix.
DKMH.PK.110.B5.02 520L0262
37
OMR
Technical Information
Technical data
TECHNICAL DATA FOR OMR WITH 25 MM AND 1 IN CYLINDRICAL SHAFT
Type
Motor size
Geometric displacement
Max. speed
OMR
50
OMR
80
OMR
100
OMR
125
OMR
160
OMR
200
OMR
250
OMR
315
OMR
375
51.6
[3.16]
775
970
100
[890]
130
[1150]
170
[1510]
7.0
[9.4]
80.3
[4.91]
750
940
195
[1730]
220
[1957]
270
[2390]
12.5
[16.8]
99.8
[6.11]
600
750
240
[2120]
280
[2480]
320
[2830]
13.0
[17.4]
125.7
[7.69]
475
600
300
[2660]
340
[3010]
370
[3280]
12.5
[16.8]
159.6
[9.77]
375
470
300
[2660]
390
[3450]
460
[4070]
10.0
[13.4]
199.8
[12.23]
300
375
300
[2660]
390
[3450]
560
[4960]
8.0
[10.7]
249.3
[15.26]
240
300
300
[2660]
380
[3360]
600
[5310]
6.0
[8.1]
315.7
[19.32]
190
240
300
[2660]
420
[3720]
610
[5400]
5.0
[6.7]
372.6
[22.80]
160
200
300
[2660]
430
[3810]
600
[5310]
4.0
[5.4]
8.5
[11.4]
140
cont.
[2030]
bar
175
int.1)
[psi]
[2540]
225
peak2)
[3260]
40
cont.
l/min
[10.6]
[US gal/min]
50
int.1)
[13.2]
bar
10
[psi]
[145]
at max. press. drop cont.
80
Nm [lbfin]
[710]
at max. press. drop int.1)
100
Nm [lbfin]
[890]
min-1
10
[rpm]
15.0
[20.1]
175
[2540]
200
[2900]
225
[3260]
60
[15.9]
75
[19.8]
10
[145]
150
[1330]
170
[1500]
15.0
[20.1]
175
[2540]
200
[2900]
225
[3260]
60
[15.9]
75
[19.8]
10
[145]
200
[1770]
230
[2040]
14.5
[19.4]
175
[2540]
200
[2900]
225
[3260]
60
[15.9]
75
[19.8]
9
[130]
250
[2210]
280
[2480]
12.5
[16.8]
130
[1890]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
7
[100]
240
[2120]
320
[2830]
10.0
[13.4]
110
[1600]
140
[2030]
225
[3260]
60
[15.9]
75
[19.8]
5
[75]
260
[2300]
330
[2920]
8.0
[10.7]
80
[1160]
110
[1600]
200
[2900]
60
[15.9]
75
[19.8]
5
[75]
240
[2120]
310
[2740]
6.5
[8.7]
70
[1020]
100
[1450]
150
[2180]
60
[15.9]
75
[19.8]
5
[75]
260
[2300]
350
[3100]
6.0
[8.1]
55
[800]
85
[1230]
130
[1890]
60
[15.9]
75
[19.8]
5
[75]
240
[2120]
380
[3360]
10
10
cm3
[in3]
min-1
[rpm]
cont.
int.1)
cont.
Max. torque
Nm
[lbfin]
int.1)
peak2)
Max. output
Min. speed3)
kW
[hp]
cont.
int.1)
1)
Intermittent operation: the permissible values may occur for max. 10% of every minute.
Peak load: the permissible values may occur for max. 1% of every minute.
3)
Operation at lower speeds may be slightly less smooth.
2)
38
DKMH.PK.110.B5.02 520L0262
OMR
Technical Information
Technical data
TECHNICAL DATA FOR OMR WITH 1 IN SPLINED AND 28.5 MM TAPERED SHAFT
Type
Motor size
Geometric displacement
Max. speed
Max. torque
Max. output
Min. speed3)
1)
2)
3)
OMR
50
OMR
80
OMR
100
OMR
125
OMR
160
OMR
200
OMR
250
OMR
315
OMR
375
51.6
[3.16]
cont.
775
int.1)
970
100
cont.
[890]
Nm
130
int.1)
[lbfin]
[1150]
170
peak2)
[1500]
7.0
cont.
kW
[9.4]
[hp]
8.5
int.1)
[11.4]
140
cont.
[2030]
bar
175
int.1)
[psi]
[2540]
225
peak2)
[3260]
40
cont.
l/min
[10.6]
[US gal/min]
50
int.1)
[13.2]
bar
10
[psi]
[145]
at max. press. drop cont.
80
Nm [lbfin]
[710]
at max. press. drop int.1)
100
Nm [lbfin]
[890]
80.3
[4.91]
750
940
195
[1730]
220
[1950]
270
[2390]
12.5
[16.8]
15.0
[20.1]
175
[2540]
200
[2900]
225
[3260]
60
[15.9]
75
[19.8]
10
[145]
150
[1330]
170
[1500]
99.8
[6.11]
600
750
240
[2120]
280
[2480]
320
[2830]
13.0
[17.4]
15.0
[20.1]
175
[2540]
200
[2900]
225
[3260]
60
[15.9]
75
[19.8]
10
[145]
200
[1770]
230
[2040]
125.7
[7.69]
475
600
300
[2660]
340
[3010]
370
[3280]
12.5
[16.8]
14.5
[19.4]
175
[2540]
200
[2900]
225
[3260]
60
[15.9]
75
[19.8]
9
[131]
250
[2210]
280
[2480]
159.6
[9.77]
375
470
360
[3190]
430
[3810]
460
[4070]
12.5
[16.8]
14.0
[18.8]
165
[2390]
200
[2900]
225
[3260]
60
[15.9]
75
[19.8]
7
[102]
300
[2660]
350
[3100]
199.8
[12.23]
300
375
360
[3190]
440
[3890]
560
[4960]
10.0
[13.4]
13.0
[17.4]
130
[1890]
175
[2540]
225
[3260]
60
[15.9]
75
[19.8]
5
[73]
300
[2660]
400
[3540]
249.3
[15.26]
240
300
360
[3190]
470
[4160]
600
[5310]
7.0
[9.4]
9.5
[12.7]
100
[1450]
140
[2030]
200
[2900]
60
[15.9]
75
[19.8]
7
[102]
290
[2570]
400
[3540]
315.7
[19.32]
190
240
360
[3190]
470
[4160]
610
[5400]
5.0
[6.7]
8.0
[10.7]
85
[1230]
115
[1670]
150
[2180]
60
[15.9]
75
[19.8]
5
[73]
315
[2790]
400
[3540]
372.6
[22.80]
160
200
360
[3190]
460
[4070]
600
[5310]
5.0
[6.7]
7.0
[9.4]
70
[1020]
90
[1310]
130
[1890]
60
[15.9]
75
[19.8]
5
[73]
300
[2660]
380
[3360]
10
10
cm3
[in3]
min-1
[rpm]
min-1
[rpm]
10
Intermittent operation: the permissible values may occur for max. 10% of every minute.
Peak load: the permissible values may occur for max. 1% of every minute.
Operation at lower speeds may be slightly less smooth.
DKMH.PK.110.B5.02 520L0262
39
OMR
Technical Information
Technical data
TECHNICAL DATA FOR OMR/OMRW WITH 32 MM , 1 1/4 IN CYLINDRICAL SHAFT AND 35 MM, 1 1/4 IN TAPERED SHAFT
Type
Motor size
Geometric displacement
Max. Speed
cm3
[in3]
min-1
[rpm]
cont.
int.1)
cont.
Max. Torque
Nm
[lbfin]
int.1)
peak2)
Max. output
cont.
kW
[hp]
int.1)
cont.
bar
[psi]
int.1)
peak2)
Min. speed3)
l/min
[USgal/min]
cont.
int.1)
bar
[psi]
at max. press.drop cont.
Nm [lbfin]
at max. press.drop int.1)
Nm [lbfin]
min-1
[rpm]
OMR
50
OMR
80
OMR
100
OMR
125
OMR
160
OMR
200
OMR
250
OMR
315
OMR
375
51.6
[3.16]
775
970
100
[890]
130
[1150]
170
[1510]
7.0
[9.4]
80.3
[4.91]
750
940
195
[1730]
220
[1950]
270
[2390]
12.5
[16.8]
99.8
[6.11]
600
750
240
[2120]
280
[2480]
320
[2830]
13.0
[17.4]
125.7
[7.69]
475
600
300
[2660]
340
[3010]
370
[3280]
12.5
[16.8]
159.6
[9.77]
375
470
380
[3360]
430
[3810]
460
[4070]
12.5
[16.8]
199.8
[12.23]
300
375
450
[3980]
500
[4430]
560
[4960]
11.0
[14.8]
249.3
[15.26]
240
300
540
[4780]
610
[5400]
710
[6280]
10.0
[13.4]
315.7
[19.32]
190
240
550
[4870]
690
[6110]
840
[7440]
9.0
[12.1]
372.6
[22.80]
160
200
580
[5130]
690
[6110]
830
[7350]
7.5
[10.1]
8.5
[11.4]
140
[2030]
175
[2540]
225
[3260]
40
[10.6]
50
[13.2]
10
[145]
80
[710]
100
[890]
15.0
[20.1]
175
[2540]
200
[2900]
225
[3260]
60
[15.9]
75
[19.8]
10
[145]
150
[1330]
170
[1500]
15.0
[20.1]
175
[2540]
200
[2900]
225
[3260]
60
[15.9]
75
[19.8]
10
[145]
200
[1770]
230
[2040]
14.5
[19.4]
175
[2540
200
[2900]
225
[3260]
60
[15.9]
75
[19.8]
9
[130]
250
[2210]
280
[2480]
14.0
[18.8]
175
[2540]
200
[2900]
225
[3260]
60
[15.9]
75
[19.8]
7
[100]
320
[2830]
370
[3280]
13.0
[17.4]
175
[2540]
200
[2900]
225
[3260]
60
[15.9]
75
[19.8]
5
[75]
410
[3630]
460
[4070]
12.0
[16.1]
175
[2540]
200
[2900]
225
[3260]
60
[15.9]
75
[19.8]
5
[75]
500
[4430]
550
[4870]
10.0
[13.4]
135
[1960]
175
[2540]
210
[3050]
60
[15.9]
75
[19.8]
5
[75]
500
[4430]
660
[5840]
9.0
[12.1]
115
[1670]
150
[2180]
175
[2540]
60
[15.9]
75
[19.8]
5
[75]
470
[4170]
570
[5050]
10
10
10
Type
OMR 50 - 375
bar
[psi]
bar
[psi]
bar
[psi]
1)
175
[2540]
200
[2900]
225
[3260]
175
[2540]
200
[2900]
225
[3260]
cont.
int.1)
peak2)
Intermittent operation: the permissible values may occur for max. 10% of every minute.
Peak load: the permissible values may occur for max. 1% of every minute.
3)
Operation at lower speeds may be slightly less smooth.
2)
40
DKMH.PK.110.B5.02 520L0262
OMR
Technical Information
Technical data max. permissible shaft seal pressure
OMR WITH HIGH
PRESSURE SHAFT SEAL
(HPS)
Max. return pressure without drain line or max. pressure in the drain line
1)
Intermittent operation: the permissible values may occur for max. 10% of every minute.
DKMH.PK.110.B5.02 520L0262
41
OMR
Technical Information
Technical data
PRESSURE DROP IN
MOTOR
The curve applies to an unloaded motor shaft and an oil viscosity of 35 mm2/s [165 SUS]
Pressure
drop
bar
[psi]
100
[1450]
140
[2030]
DIRECTION OF SHAFT
ROTATION
42
DKMH.PK.110.B5.02 520L0262
Viscosity
mm2/s
[SUS]
Oil flow in
drain line
l/min
[US gal/min]
20
[100]
35
[165]
20
[100]
35
[165]
2.5
[0.66]
1.8
[0.78]
3.5
[0.93]
2.8
[0.74]
OMR
Technical Information
Technical data
PERMISSIBLE SHAFT
LOAD FOR OMR
Shaft version
Permissible
shaft load (PR) l in mm
Permissible
shaft load (PR) l in inch
Square flange**
2-hole oval flange
(US version)
25 mm cylindrical shaft
1 in cylindrical shaft
1 in splined shaft
28.5 mm tapered shaft
32 mm cylindrical shaft
11/4 in cylindrical shaft
25 mm cylindrical shaft
1 in cylindrical shaft
800 250000 N*
n
95 + l
800 187500 N*
n
95 + l
800 250000 N*
n
101 + l
DKMH.PK.110.B5.02 520L0262
43
OMR
Technical Information
Technical data
PERMISSIBLE SHAFT
LOAD FOR OMRW N
WITH NEEDLE BEARINGS
C
A:
B:
C:
D:
The output shaft on OMRW N runs in needle bearings. These bearings and the recessed
mounting flange allow a higher permissible radial load in comparison to OMR motors
with slide bearings.
The permissible radial load on the shaft is shown for different speeds as a function of the
distance from the mounting flange to the point of load application.
Curve A shows max. radial shaft load. Any shaft load exceeding the values quoted in the
curve will involve a risk of breakage.
The other curves apply to a B10 bearing life of 2000 hours at the number of revolutions
indicated by the curve letter. Mineral based hydraulic oil with a sufficient content of
anti-wear additives must be used.
Bearing life calculations can be made using the explanation and formula provided
in the chapter Bearing dimensioning in the technical information "General"
DHMH.PK.100.G2.02 520L0232.
44
DKMH.PK.110.B5.02 520L0262
OMR
Technical Information
Function diagrams
FUNCTION DIAGRAMS
Explanation of function diagram use, basis and conditions can be found on page 7.
A: Continuous range
B: Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent pressure drop for the actual shaft version can
be found on page 38-40.
Note: Intermittent pressure drop and oil flow must not occur simultaneously.
DKMH.PK.110.B5.02 520L0262
45
OMR
Technical Information
Function diagrams
FUNCTION DIAGRAMS
Explanation of function diagram use, basis and conditions can be found on page 7.
A: Continuous range
B: Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent pressure drop for the actual shaft version can
be found on page 38-40.
Note: Intermittent pressure drop and oil flow must not occur simultaneously.
46
DKMH.PK.110.B5.02 520L0262
OMR
Technical Information
Function diagrams
FUNCTION DIAGRAMS
Explanation of function diagram use, basis and conditions can be found on page 7.
A: Continuous range
B: Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent pressure drop for the actual shaft version can
be found on page 38-40.
Note: Intermittent pressure drop and oil flow must not occur simultaneously.
DKMH.PK.110.B5.02 520L0262
47
OMR
Technical Information
Function diagrams
FUNCTION DIAGRAMS
Explanation of function diagram use, basis and conditions can be found on page 7.
A: Continuous range
B: Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent pressure drop for the actual shaft version can
be found on page 38-40.
Note: Intermittent pressure drop and oil flow must not occur simultaneously.
48
DKMH.PK.110.B5.02 520L0262
OMR
Technical Information
Function diagrams
FUNCTION DIAGRAMS
Explanation of function diagram use, basis and conditions can be found on page 7.
A: Continuous range
B: Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent pressure drop for the actual shaft version can
be found on page 38-40.
Note: Intermittent pressure drop and oil flow must not occur simultaneously.
DKMH.PK.110.B5.02 520L0262
49
OMR
Technical Information
Shaft version
SHAFT VERSION
A: Cylindrical shaft
25 mm
D: Parallel key
A8 7 32
DIN 6885
B: Cylindrical shaft
1 in
E: Parallel key
1
4 14 1 14 in
B.S. 46
US version
C: Cylindrical shaft
1 in
F: Parallel key
1
4 14 1 14 in
B.S. 46
50
DKMH.PK.110.B5.02 520L0262
OMR
Technical Information
Shaft version
SHAFT VERSION
D: Cylindrical shaft
32 mm
G: Parallel key
A10 8 45
DIN 6885
US version
E: Cylindrical shaft
1 14 in
H: Parallel key
5
16 516 1 14 in
B.S. 46
DKMH.PK.110.B5.02 520L0262
51
OMR
Technical Information
Shaft version
SHAFT VERSION
US version
G: Splined shaft
SAE 6 B (B.S. 2059)
Straight-sided,
bottom fitting, deep.
Fit 2
Nom. size 1 in
* Deviates from
SAE 6 B (B.S. 2059)
I: Tapered shaft 35 mm
(ISO/R775)
N: DIN 937
NV 41
Tightening torque:
200 10 Nm [1770 85 lbfin]
M: Taper 1:10
P: Parallel key
B6 6 20
DIN 6885
52
DKMH.PK.110.B5.02 520L0262
OMR
Technical Information
Shaft version
SHAFT VERSION
DKMH.PK.110.B5.02 520L0262
53
OMR
Technical Information
Technical data
PORT THREAD VERSIONS
A: G main ports
G: ISO 228/1 - G1/2
151-1844.10
D: G drain port
E: ISO 228/1 - G1/4
54
DKMH.PK.110.B5.02 520L0262
OMR
Technical Information
Dimensions European version
DIMENSIONS
Type
OMR 50
OMR 80
OMR 100
OMR 125
OMR 160
OMR 200
OMR 250
OMR 315
OMR 375
Side port version with 2-hole oval mounting flange (A2 flange).
With high pressure shaft seal.
mm mm
L
[in] 1 [in]
135.5
[5.33]
140.5
[5.53]
144.0
[5.67]
148.5
[5.85]
154.5
[6.08]
161.5
[6.36]
170.5
[6.71]
181.5
[7.15]
191.7
[7.55]
9.0
[0.35]
14.0
[0.55]
17.4
[0.69]
21.8
[0.86]
27.8
[1.09]
34.8
[1.37]
43.5
[1.71]
54.8
[2.16]
65.0
[2.56]
DKMH.PK.110.B5.02 520L0262
55
OMR
Technical Information
Dimensions European version
DIMENSIONS
Type
OMR 50
OMR 80
OMR 100
OMR 125
OMR 160
OMR 200
OMR 250
OMR 315
OMR 375
Side port version with 2-hole oval mounting flange (A2 flange).
With check valves and drain connection.
With high pressure shaft seal.
mm mm
L
[in] 1 [in]
135.5
[5.33]
140.5
[5.53]
144.0
[5.67]
148.5
[5.85]
154.5
[6.08]
161.5
[6.36]
170.5
[6.71]
181.5
[7.15]
191.7
[7.55]
9.0
[0.35]
14.0
[0.55]
17.4
[0.69]
21.8
[0.86]
27.8
[1.09]
34.8
[1.37]
43.5
[1.71]
54.8
[2.16]
65.0
[2.56]
C: Drain connection
G 14; 12 mm [0.47 in] deep
D: G 12; 15 mm [0.59 in] deep
E: M8; 13 mm [0.51 in] deep
(4 pcs.)
56
DKMH.PK.110.B5.02 520L0262
OMR
Technical Information
Dimensions European version
DIMENSIONS
Side port version with 2-hole oval mounting flange (A2 flange).
Type
OMR 50
OMR 80
OMR 100
OMR 125
OMR 160
OMR 200
OMR 250
OMR 315
OMR 375
mm
[in]
68.3
[2.69]
55.3
[2.16]
56.3
[2.19]
mm mm
L
[in] 1 [in]
135.5
[5.33]
140.5
[5.53]
144.0
[5.67]
148.5
[5.85]
154.5
[6.08]
161.5
[6.36]
170.5
[6.71]
181.5
[7.15]
191.7
[7.55]
9.0
[0.35]
14.0
[0.55]
17.4
[0.69]
21.8
[0.86]
27.8
[1.09]
34.8
[1.37]
43.5
[1.71]
54.8
[2.16]
65.0
[2.56]
C: Drain connection
G 14; 12 mm [0.47 in] deep
D: G 12; 15 mm [0.59 in] deep
E: M8; 13 mm [0.51 in] deep
(4 pcs.)
DKMH.PK.110.B5.02 520L0262
57
OMR
Technical Information
Dimensions European version
DIMENSIONS
Type
OMR 50
OMR 80
OMR 100
OMR 125
OMR 160
OMR 200
OMR 250
OMR 315
OMR 400
mm mm
L
[in] 1 [in]
150.6
[5.92]
155.6
[6.13]
159.0
[6.26]
163.4
[6.43]
169.4
[6.67]
176.4
[6.94]
185.1
[7.29]
196.4
[7.73]
206.6
[8.13]
9.0
[0.35]
14.0
[0.55]
17.4
[0.69]
21.8
[0.86]
27.8
[1.09]
34.8
[1.37]
43.5
[1.71]
54.8
[2.16]
65.0
[2.56]
C: Drain connection
G 14; 12 mm [0.47 in] deep
D: G 12; 15 mm [0.59 in] deep
58
DKMH.PK.110.B5.02 520L0262
OMR
Technical Information
Dimensions US version
DIMENSIONS
mm mm
L
[in] 1 [in]
Type
OMR 50
141.5
[5.57]
146.5
[5.77]
150.0
[5.91]
154.4
[6.08]
160.5
[6.32]
167.5
[6.59]
176.5
[6.95]
187.5
[7.38]
197.5
[7.78]
OMR 80
OMR 100
OMR 125
OMR 160
OMR 200
OMR 250
OMR 315
OMR 400
9.0
[0.35]
14.0
[0.55]
17.4
[0.69]
21.8
[0.86]
27.8
[1.09]
34.8
[1.37]
43.5
[1.71]
54.8
[2.16]
64.8
[2.55]
C: Drain connection
7
16 - 20 UNF;
12 mm [0.47 in] deep
D: 78 - 14 UNF;
16.76 mm [0.66 in] deep
E: M8; 13 mm [0.51 in] deep
(4-off )
DKMH.PK.110.B5.02 520L0262
59
OMR
Technical Information
Dimensions European version
DIMENSIONS
Side port version with 4-hole oval mounting flange (A4 flange).
Type
OMR 50
OMR 80
OMR 100
OMR 125
OMR 160
OMR 200
OMR 250
OMR 315
OMR 375
mm
[in]
68.3
[2.69]
55.3
[2.18]
mm mm
L
[in] 1 [in]
135.5
[5.33]
140.5
[5.53]
144.0
[5.67]
148.5
[5.85]
154.5
[6.08]
161.5
[6.36]
170.5
[6.71]
181.5
[7.15]
191.7
[7.55]
9.0
[0.35]
14.0
[0.55]
17.4
[0.69]
21.8
[0.86]
27.8
[1.09]
34.8
[1.37]
43.5
[1.71]
54.8
[2.16]
65.0
[2.56]
C: Drain connection
G 14; 12 mm [0.47 in] deep
D: G 12; 15 mm [0.59 in] deep
E: M8; 13 mm [0.51 in] deep
(4 pcs.)
60
DKMH.PK.110.B5.02 520L0262
OMR
Technical Information
Dimensions US version
DIMENSIONS
Type
OMR 50
OMR 80
OMR 100
OMR 125
OMR 160
OMR 200
OMR 250
OMR 315
OMR 400
mm mm
L
[in] 1 [in]
135.5
[5.33]
140.5
[5.53]
144.0
[5.67]
148.4
[5.84]
154.5
[6.08]
161.5
[6.36]
170.5
[6.71]
181.5
[7.15]
191.5
[7.55]
9.0
[0.35]
14.0
[0.55]
17.4
[0.69]
21.8
[0.86]
27.8
[1.09]
34.8
[1.37]
43.5
[1.71]
54.8
[2.16]
64.8
[2.55]
C: Drain connection
7
16 - 20 UNF;
12 mm [0.47 in] deep
D: 78 - 14 UNF;
16.76 mm [0.66 in] deep
E: M8; 13 mm [0.51 in] deep
(4-off )
DKMH.PK.110.B5.02 520L0262
61
OMR
Technical Information
Dimensions European version
DIMENSIONS
Type
OMR 50
OMR 80
OMR 100
OMR 125
OMR 160
OMR 200
OMR 250
OMR 315
OMR 375
mm mm
L
[in] 1 [in]
156.6
[6.17]
161.6
[6.36]
165.0
[6.50]
169.4
[6.67]
175.4
[6.91]
182.4
[7.18]
191.1
[7.52]
202.4
[7.98]
212.5
[8.37]
9.0
[0.35]
14.0
[0.55]
17.4
[0.69]
21.8
[0.86]
27.8
[1.09]
34.8
[1.37]
43.5
[1.71]
54.8
[2.16]
65.0
[2.56]
C: Drain connection
G 14; 12 mm [0.47 in] deep
D: G 12; 15 mm [0.59 in] deep
E: M10; 15 mm [0.59 in] deep
(4 pcs.)
62
DKMH.PK.110.B5.02 520L0262
OMR
Technical Information
Dimensions US version
DIMENSIONS
Type
OMR 50
OMR 80
OMR 100
OMR 125
OMR 160
OMR 200
OMR 250
OMR 315
OMR 375
mm mm
L
[in] 1 [in]
141.5
[5.57]
146.5
[5.77]
150.0
[5.91]
154.4
[6.08]
160.5
[6.32]
167.5
[6.59]
176.5
[6.95]
187.5
[7.38]
197.7
[7.78]
9.0
[0.35]
14.0
[0.55]
17.4
[0.69]
21.8
[0.86]
27.8
[1.09]
34.8
[1.37]
43.5
[1.71]
54.8
[2.16]
64.8
[2.55]
C: Drain connection
7
16 - 20 UNF;
12 mm [0.47 in] deep
7
D: 8 - 14 UNF;
17 mm [0.66 in] deep
E: M8; 13 mm [0.51 in] deep
(4-off )
F: 3/8 - 16 UNC;
15 mm [0.59 in] deep
(4-off )
DKMH.PK.110.B5.02 520L0262
63
OMR
Technical Information
Dimensions European version
DIMENSIONS
Type
OMRW 50N
OMRW 80N
OMRW 100N
OMRW 125N
OMRW 160N
OMRW 200N
OMRW 250N
OMRW 315N
OMRW 375N
mm mm
L
[in] 1 [in]
106.0
[4.17]
111.0
[4.37]
114.4
[4.50]
118.8
[4.68]
124.8
[4.91]
131.8
[5.19]
140.5
[5.53]
152.0
[5.98]
162.0
[6.38]
9.0
[0.35]
14.0
[0.55]
17.4
[0.69]
21.8
[0.86]
27.8
[1.09]
34.8
[1.37]
43.5
[1.71]
54.8
[2.16]
65.0
[2.56]
C: Drain connection
G 14; 12 mm [0.47 in] deep
D: G 12; 15 mm [0.59 in] deep
64
DKMH.PK.110.B5.02 520L0262
OMR
Technical Information
Dimensions US version
DIMENSIONS
Type
OMRW 50N
OMRW 80N
OMRW 100N
OMRW 125N
OMRW 160N
OMRW 200N
OMRW 250N
OMRW 315N
OMRW 375N
mm mm
L
[in] 1 [in]
106.0
[4.17]
111.0
[4.37]
114.4
[4.50]
118.8
[4.68]
124.8
[4.91]
131.8
[5.19]
140.5
[5.53]
152.0
[5.98]
162.0
[6.38]
9.0
[0.35]
14.0
[0.55]
17.4
[0.69]
21.8
[0.86]
27.8
[1.09]
34.8
[1.37]
43.5
[1.71]
54.8
[2.16]
65.0
[2.56]
C: Drain connection
7
16 - 20 UNF
12 mm [0.47 in] deep
D: 78 - 14 UNF
17 mm [0.66 in] deep
DKMH.PK.110.B5.02 520L0262
65
OMH
Technical Information
Versions
Cyl. 32 mm
Cyl. 35 mm
4 hole oval Cyl. 1 1/4 in
flange
Splined 1 in SAE 6B
(A4-flange) Splined 1 1/4 in
Splined 1 1/4 in
Tapered 35 mm
G 1/2
G 1/2
7
/8 - 14 UNF
7
/8 - 14 UNF
G 1/2
7
/8 - 14 UNF
G 1/2
X
X
X
X
X
X
X
X
X
X
X
X
X
X
66
DKMH.PK.110.B5.02 520L0262
X
X
X
X
X
X
X
Specials
Check valve
Drain connection
US version
European version
Port size
Shaft
Mounting flange
VERSIONS
Yes
Yes
OMH
Yes
Yes
OMH
Yes
Yes
OMH
Yes
Yes
OMH
Yes
Yes
OMH
Yes
Yes
OMH
Yes
Yes
OMH
Function diagram see page :
OMH
Technical Information
Code Numbers
CODE NUMBERS
250
315
400
500
1002
1012
1042
1080
1022
1052
-
1003
1013
1043
1082
1023
1053
-
1004
1014
1044
1083
1024
1054
1034
1005
1015
1045
1084
1025
1055
1035
1006
1016
1046
1081
1026
1056
1036
74
74
75
75
76
Dimensions Page
200
151H
151H
151H
151H
151H
151H
151H
CODE NUMBERS
DISPLACEMENT [cm3]
69
70
69
68
70
70
70
81
81
82
82
81
82
81
Ordering
Add the four digit prefix 151H to the four digit numbers from the chart for complete
code number.
Example:
151H1044 for an OMH 315 with A4 flange, cyl. 1 1/4 in shaft, port size 7/8 - 14 UNF.
Note: Orders will not be accepted without the four digit prefix.
DKMH.PK.110.B5.02 520L0262
67
OMH
Technical Information
Technical data
TECHNICAL DATA FOR OMH WITH 1 IN SAE 6 B SPLINED SHAFT
Type
Motor size
Geometric displacement
Max. speed
cm3
[in3]
min-1
[rpm]
cont.
int.1)
cont.
Max. torque
Nm
[lbfin]
int.1)
peak2)
Max. output
cont.
kW
[hp]
int.1)
cont.
bar
[psi]
int.1)
peak2)
Min. speed3)
l/min
[US gal/min]
cont.
int.1)
bar
[psi]
at max. press. drop cont.
Nm [lbfin]
at max. press. drop int.1)
Nm [lbfin]
min-1
[rpm]
OMH
200
OMH
250
OMH
315
OMH
400
OMH
500
201.3
[12.32]
370
445
340
[3000]
510
[4500]
610
[5400]
11.2
[15.0]
252.0
[15.42]
295
350
340
[3000]
510
[4500]
610
[5400]
7.5
[10.0]
314.9
[19.27]
235
285
340
[3000]
540
[4800]
610
[5400]
5.2
[7.0]
396.8
[24.28]
185
225
340
[3000]
540
[4800]
610
[5400]
4.8
[6.5]
470.6
[28.80]
155
190
340
[3000]
520
[4600]
610
[5400]
3.7
[5.0]
17.2
[23.0]
115
[1650]
170
[2500]
215
[3120]
75
[19.8]
90
[23.8]
7
[100]
255
[2250]
390
[3450]
11.9
[16.0]
90
[1300]
145
[2100]
175
[2540]
75
[19.8]
90
[23.8]
7
[100]
270
[2400]
435
[3850]
9.7
[13.0]
75
[1100]
120
[1750]
145
[2100]
75
[19.8]
90
[23.8]
7
[100]
280
[2500]
450
[4000]
8.2
[11.0]
60
[900]
95
[1400]
110
[1600]
75
[19.8]
90
[23.8]
7
[100]
290
[2550]
450
[4000]
6.0
[8.0]
50
[725]
75
[1100]
90
[1300]
75
[19.8]
90
[23.8]
7
[100]
300
[2650]
450
[4000]
10
10
1)
Intermittent operation: the permissible values may occur for max. 10% of every minute.
Peak load: the permissible values may occur for max. 1% of every minute.
3)
Operation at lower speeds may be slightly less smooth.
2)
68
DKMH.PK.110.B5.02 520L0262
OMH
Technical Information
Technical data
TECHNICAL DATA FOR OMH WITH 32 MM AND 1 1/4 IN CYLINDRICAL SHAFT
Type
Motor size
Geometric displacement
Max. speed
cm3
[in3]
min-1
[rpm]
cont.
int.1)
cont.
Max. torque
Nm
[lbfin]
int.1)
peak2)
Max. output
cont.
kW
[hp]
int.1)
cont.
bar
[psi]
int.1)
peak2)
Min. speed3)
l/min
[US gal/min]
cont.
int.1)
bar
[psi]
at max. press. drop cont.
Nm [lbfin]
at max. press. drop int.1)
Nm [lbfin]
min-1
[rpm]
OMH
200
OMH
250
OMH
315
OMH
400
OMH
500
201.3
[12.32]
370
445
510
[4510]
580
[5130]
640
[5660]
16.0
[21.5]
252.0
[15.42]
295
350
610
[5400]
700
[6200]
790
[6990]
16.0
[21.5]
314.9
[19.27]
235
285
590
[5220]
670
[5930]
840
[7440]
12.5
[16.8]
396.8
[24.28]
185
225
590
[5220]
700
[6200]
840
[7440]
10.0
[13.4]
470.6
[28.80]
155
190
580
[5130]
680
[6020]
840
[7440]
8.5
[11.4]
18.5
[24.8]
175
[2540]
200
[2900]
225
[3260]
75
[19.8]
90
[23.8]
5
[75]
390
[3450]
450
[3980]
18.5
[24.8]
175
[2540]
200
[2900]
225
[3260]
75
[19.8]
90
[23.8]
5
[75]
520
[4600]
590
[5220]
14.0
[18.8]
135
[1960]
155
[2250]
190
[2760]
75
[19.8]
90
[23.8]
5
[75]
510
[4510]
590
[5220]
12.0
[16.1]
105
[1520]
125
[1810]
155
[2250]
75
[19.8]
90
[23.8]
5
[75]
490
[4340]
600
[5310]
10.0
[13.4]
85
[1230]
100
[1450]
130
[1890]
75
[19.8]
90
[23.8]
5
[75]
490
[4340]
600
[5310]
10
10
1)
Intermittent operation: the permissible values may occur for max. 10% of every minute.
Peak load: the permissible values may occur for max. 1% of every minute.
3)
Operation at lower speeds may be slightly less smooth.
2)
DKMH.PK.110.B5.02 520L0262
69
OMH
Technical Information
Technical data
TECHNICAL DATA FOR OMH WITH 35 MM CYLINDRICAL, 1 1/4 IN SPLINED AND 35 MM TAPERED SHAFT
Type
Motor size
Geometric displacement
Max. speed
cm3
[in3]
min-1
[rpm]
cont.
int.1)
cont.
Max. torque
Nm
[lbfin]
int.1)
peak2)
Max. output
cont.
kW
[hp]
int.1)
cont.
bar
[psi]
int.1)
peak2)
Min. speed3)
l/min
[US gal/min]
cont.
int.1)
bar
[psi]
at max. press. drop cont.
Nm [lbfin]
at max. press. drop int.1)
Nm [lbfin]
min-1
[rpm]
OMH
200
OMH
250
OMH
315
OMH
400
OMH
500
201.3
[12.32]
370
445
510
[4510]
580
[5130]
252.0
[15.42]
295
350
610
[5400]
700
[6200]
314.9
[19.27]
235
285
740
[6550]
820
[7260]
396.8
[24.28]
185
225
840
[7440]
980
[8670]
470.6
[28.80]
155
190
820
[7260]
1040
[9210]
640
[5660]
16.0
[21.5]
18.5
[24.8]
175
[2540]
200
[2900]
225
[3260]
75
[19.8]
90
[23.8]
5
[75]
390
[3450]
450
[3980]
790
[6990]
16.0
[21.5]
18.5
[24.8]
175
[2540]
200
[2900]
225
[3260]
75
[19.8]
90
[23.8]
5
[75]
520
[4600]
590
[5220]
980
[8670]
14.0
[18.8]
15.5
[20.8]
175
[2540]
200
[2900]
225
[3260]
75
[19.8]
90
[23.8]
5
[75]
660
[5840
730
[6460]
1090
[9650]
12.5
[16.8]
15.0
[20.1]
155
[2250]
190
[2760]
210
[3050]
75
[19.8]
90
[23.8]
5
[75]
720
[6370]
880
[7790]
1170
[10360]
11.0
[14.8]
14.0
[18.8]
125
[1810]
160
[2320]
180
2610]
75
[19.8]
90
[23.8]
5
[75]
720
[6370]
880
[7790]
10
10
Type
bar
[psi]
bar
[psi]
bar
[psi]
1)
200
[2900]
225
[3260]
250
[3630]
175
[2540]
200
[2900]
225
[3260]
cont.
int.1)
peak2)
Intermittent operation: the permissible values may occur for max. 10% of every minute.
Peak load: the permissible values may occur for max. 1% of every minute.
3)
Operation at lower speeds may be slightly less smooth.
2)
70
DKMH.PK.110.B5.02 520L0262
OMH
Technical Information
Technical data
MAX. PERMISSIBLE
SHAFT SEAL PRESSURE
Max. return pressure without drain line or max. pressure in the drain line
1)
Intermittent operation: the permissible values may occur for max. 10% of every minute.
DKMH.PK.110.B5.02 520L0262
71
OMH
Technical Information
Technical data
PRESSURE DROP IN
MOTOR
The curve applies to an unloaded motor shaft and an oil viscosity of 35 mm2/s [165 SUS]
Pressure
drop
bar
[psi]
100
[1450]
140
[2030]
DIRECTION OF SHAFT
ROTATION
72
DKMH.PK.110.B5.02 520L0262
Viscosity
mm2/s
[SUS]
Oil flow in
drain line
l/min
[US gal/min]
20
[100]
35
[165]
20
[100]
35
[165]
2.5
[0.66]
1.8
[0.78]
3.5
[0.93]
2.8
[0.74]
OMH
Technical Information
Technical data
PERMISSIBLE SHAFT
LOADS FOR OMH
The permissible shaft load (Prad) is calculated from the speed (n) and the distance (l)
between the point of load application and the mounting flange.
Prad =
1100
250000
N*; l in mm
n
103.5 + l
Prad =
1100
2215
4.07 + l
lbf*; l in inch
DKMH.PK.110.B5.02 520L0262
73
OMH
Technical Information
Function diagrams
FUNCTION DIAGRAMS
Explanation of function diagram use, basis and conditions can be found on page 7.
A: Continuous range
B: Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent pressure drop for the actual shaft version can
be found on page 68-70.
Note: Intermittent pressure drop and oil flow must not occur simultaneously.
74
DKMH.PK.110.B5.02 520L0262
OMH
Technical Information
Function diagrams
FUNCTION DIAGRAMS
Explanation of function diagram use, basis and conditions can be found on page 7.
A: Continuous range
B: Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent pressure drop for the actual shaft version can
be found on page 68-70.
Note: Intermittent pressure drop and oil flow must not occur simultaneously.
DKMH.PK.110.B5.02 520L0262
75
OMH
Technical Information
Function diagrams
FUNCTION DIAGRAMS
Explanation of function diagram use, basis and conditions can be found on page 7.
A: Continuous range
B: Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent pressure drop for the actual shaft version can
be found on page 68-70.
Note: Intermittent pressure drop and oil flow must not occur simultaneously.
76
DKMH.PK.110.B5.02 520L0262
OMH
Technical Information
Shaft version
SHAFT VERSION
A: Cylindrical shaft
32 mm
D: Parallel key
A10 8 45
DIN 6885
B: Cylindrical shaft
35 mm
E: Parallel key
A10 8 45
DIN 6885
US version
C: Cylindrical shaft
1 1/4 in
F: Parallel key
5
/16 5/16 11/4 in
SAE J 744
DKMH.PK.110.B5.02 520L0262
77
OMH
Technical Information
Shaft version
SHAFT VERSION
D: Splined shaft
SAE 6 B (B.S. 2059)
Straight-sided,
bottom fitting, deep.
Fit 2
Nom. size 1 in
*Deviates from
SAE 6 B (B.S. 2059)
78
DKMH.PK.110.B5.02 520L0262
OMH
Technical Information
Shaft version
SHAFT VERSION
US version
F. Involute splined shaft
ANS B92.1 - 1970 standard
Flat root side fit
Pitch 12/24
Teeth 14
Major dia. 1.25 in
Pressure angle 30
G: Tapered shaft 35 mm
(ISO/R775)
I: DIN 937
NV 410
Tightening torque:
200 10 Nm [1770 85 lbfin]
H: Taper 1:10
L: Parallel key
B6 6 20
DIN 6885
DKMH.PK.110.B5.02 520L0262
79
OMH
Technical Information
Technical data
PORT THREAD VERSIONS
A: G main ports
E: ISO 228/1 - G1/2
C: G drain port
G: ISO 228/1 - G1/4
80
DKMH.PK.110.B5.02 520L0262
OMH
Technical Information
Dimensions European version
DIMENSIONS
Type
OMH 200
OMH 250
OMH 315
OMH 400
OMH 500
mm mm
L
[in] 1 [in]
170.1
[6.70]
177.1
[6.97]
185.8
[7.31]
197.1
[7.76]
207.3
[8.16]
27.8
[1.09]
34.8
[1.37]
43.5
[1.71]
54.8
[2.16]
65.0
[2.56]
C: Drain connection
G 14; 12 mm [0.47 in] deep
D: G 12; 15 mm [0.59 in] deep
DKMH.PK.110.B5.02 520L0262
81
OMH
Technical Information
Dimensions US version
DIMENSIONS
Side port version with 4 hole oval mounting flange (A4 flange).
mm
[in]
L2
Splined shaft
1 in
Other shaft
versions
50.5
[1.99]
58.0
[2.28]
Type
OMH 200
OMH 250
OMH 315
OMH 400
OMH 500
mm mm
L
[in] 1 [in]
170.1
[6.70]
177.1
[6.97]
185.8
[7.31]
197.1
[7.76]
207.3
[8.16]
27.8
[1.09]
34.8
[1.37]
43.5
[1.71]
54.8
[2.16]
65.0
[2.56]
C: Drain connection
7
16 - 20 UNF;
12 mm [0.47 in] deep
7
D: 8 - 14 UNF;
15 mm [0.59 in] deep
82
DKMH.PK.110.B5.02 520L0262
OMH
Technical Information
Notes
NOTES
DKMH.PK.110.B5.02 520L0262
83
OMEW
Technical Information
Versions
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Specials
Check valve
Drain connection
Clockwise shaft
rotation (CW version)1)
G 1/2
G 1/2
7
/8 - 14 UNF
7
/8 - 14 UNF
US version
Tapered 35 mm
Tapered 35 mm
Tapered 1 1/4 in
Tapered 1 1/4 in
European version
Port size
Wheel
Shaft
Mounting flange
VERSIONS
No
No
OMEW
No
No
OMEW
No
No
OMEW
No
No
OMEW
Function diagram see page :
1) Direction of rotation
In the application mainly involves operation in one direction, we therefore recommend a corresponding motor with either CW- or CCW-rotation.
High pressure seals
Since all OMEW motors are fited with a high-pressure shaft seal, there is no need for a drain line.
84
DKMH.PK.110.B5.02 520L0262
OMEW
Technical Information
Code Numbers
CODE NUMBERS
CODE NUMBERS
100
125
160
200
250
315
Dimensions Page
DISPLACEMENT [cm3]
151H
151H
151H
151H
2002
2011
3002
3011
2003
2012
3003
3012
2004
2013
3004
3013
2005
2014
3005
3014
2006
2015
3006
3015
2007
2016
3007
3016
86
86
86
86
95
95
96
96
90
90
91
91
92
92
Ordering
Add the four digit prefix 151H to the four digit numbers from the chart for complete
code number.
Example:
151H2015 for an OMEW 250 with 35 mm tapered shaft, port size G 1/2 and counter
clockwise rotation (CCW).
Note: Orders will not be accepted without the four digit prefix.
DKMH.PK.110.B5.02 520L0262
85
OMEW
Technical Information
Technical data
TECHNICAL DATA FOR OMEW WITH 35 MM AND 1 1/4 IN TAPERED SHAFT
Type
Motor size
Geometric displacement
Max. speed
cm3
[in3]
min-1
[rpm]
cont.
int.1)
cont.
Max. torque
Nm
[lbfin]
int.1)
peak2)
Max. output
cont.
kW
[hp]
int.1)
cont.
bar
[psi]
int.1)
peak2)
Min. speed3)
l/min
[US gal/min]
cont.
int.1)
bar
[psi]
at max. press. drop cont.
Nm [lbfin]
at max. press. drop int.1)
Nm [lbfin]
min-1
[rpm]
OMEW
100
OMEW
125
OMEW
160
OMEW
200
OMEW
250
OMEW
315
99.8
[6.11]
600
750
250
[2210]
270
[2390]
290
[2570]
12.0
[16.1]
124.1
[7.60]
475
695
320
[2830]
340
[3010]
360
[3190]
12.0
[16.1]
155.4
[9.51]
375
470
410
[3630]
430
[3810]
460
[4070]
12.0
[16.1]
198.2
[12.13]
300
375
470
[4160]
510
[4510]
570
[5040]
11.0
[14.8]
248.1
[15.18]
240
300
510
[4510]
570
[5040]
640
[5660]
10.0
[13.4]
310.1
[18.98]
190
240
520
[4600]
640
[5660]
740
[6550]
8.0
[10.7]
15.0
[20.1]
200
[2900]
210
[3050]
225
[3260]
60
[15.9]
75
[19.8]
10
[145]
230
[2040]
240
[2120]
15.0
[20.1]
200
[2900]
210
[3050]
225
[3260]
60
[15.9]
75
[19.8]
7
[100]
290
[2570]
300
[2660]
15.0
[20.1]
200
[2900]
210
[3050]
225
[3260]
60
[15.9]
75
[19.8]
7
[100]
360
[3190]
380
[3360]
14.0
[18.8]
185
[2680]
200
[2900]
225
[3260]
60
[15.9]
75
[19.8]
7
[100]
420
[3720]
460
[4070]
12.0
[16.1]
160
[2320]
180
[2610]
200
[2900]
60
[15.9]
75
[19.8]
7
[100]
460
[4070]
520
[4600]
10.0
[13.4]
130
[1890]
160
[2320]
185
[2680]
60
[15.9]
75
[19.8]
7
[100]
470
[4160]
570
[5040]
10
Type
bar
[psi]
bar
[psi]
bar
[psi]
1)
200
[2900]
210
[3050]
225
[3260]
200
[2900]
210
[3050]
225
[3260]
cont.
int.1)
peak2)
Intermittent operation: the permissible values may occur for max. 10% of every minute.
Peak load: the permissible values may occur for max. 1% of every minute.
3)
Operation at lower speeds may be slightly less smooth.
2)
86
DKMH.PK.110.B5.02 520L0262
OMEW
Technical Information
Technical data
MAX. PERMISSIBLE
SHAFT SEAL PRESSURE
DKMH.PK.110.B5.02 520L0262
87
OMEW
Technical Information
Technical data
PRESSURE DROP IN
MOTOR
The curve applies to an unloaded motor shaft and an oil viscosity of 35 mm2/s [165 SUS]
DIRECTION OF SHAFT
ROTATION
88
DKMH.PK.110.B5.02 520L0262
OMEW
Technical Information
Technical data
PERMISSIBLE SHAFT
LOADS FOR OMEW
As the OMEW output shaft is embedded in needle bearings and the mounting flange is
recessed it is possible to fit a wheel hub direct onto the shaft so that the radial load acts
midway between the needle bearings.
Based upon the requested max. speed and the point of action of the radial load the
permissible shaft load can be read from the curved shown below.
Curve A shows the max. radial load. If the radial load exceeds these values there is a
potential risk of breaksown.
The other curves apply to a B10 bearing life of 2000 hours at the indicated speed when
applying a hydraulic mineral oil with an adequate content of anti-wear additives.
The longevity can also be calculated by means of the Bearing dimensions instructions in
the technical information General DKMH.PK.100.G2.02 520L0232.
A:
B:
C:
D:
E:
F:
G:
DKMH.PK.110.B5.02 520L0262
89
OMEW
Technical Information
Function diagrams
FUNCTION DIAGRAMS
Explanation of function diagram use, basis and conditions can be found on page 7.
A: Continuous range
B: Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent pressure drop for the actual shaft version can
be found on page 86.
Note: Intermittent pressure drop and oil flow must not occur simultaneously.
90
DKMH.PK.110.B5.02 520L0262
OMEW
Technical Information
Function diagrams
FUNCTION DIAGRAMS
Explanation of function diagram use, basis and conditions can be found on page 7.
A: Continuous range
B: Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent pressure drop for the actual shaft version can
be found on page 86.
Note: Intermittent pressure drop and oil flow must not occur simultaneously.
DKMH.PK.110.B5.02 520L0262
91
OMEW
Technical Information
Function diagrams
FUNCTION DIAGRAMS
Explanation of function diagram use, basis and conditions can be found on page 7.
A: Continuous range
B: Intermittent range (max. 10% operation every minute)
Max. permissible continuous/intermittent pressure drop for the actual shaft version can
be found on page 86.
Note: Intermittent pressure drop and oil flow must not occur simultaneously.
92
DKMH.PK.110.B5.02 520L0262
OMEW
Technical Information
Shaft version
SHAFT VERSION
A: Tapered shaft 35 mm
(ISO/R775)
N: DIN 937
NV 41
Tightening torque:
200 10 Nm [1770 85 lbfin]
C: Taper 1:10
F: Parallel key
B6 6 20
DIN 6885
DKMH.PK.110.B5.02 520L0262
93
OMEW
Technical Information
Technical data
PORT THREAD VERSIONS
151-1857.10
A: G main ports
G: ISO 228/1 - G1/2
94
DKMH.PK.110.B5.02 520L0262
OMEW
Technical Information
Dimensions European version
DIMENSIONS
Type
OMEW 100
OMEW 125
OMEW 160
OMEW 200
OMEW 250
OMEW 315
mm mm
L
[in] 1 [in]
107.9
[4.25]
111.3
[4.38]
115.7
[4.56]
121.7
[4.79]
128.7
[5.07]
137.4
[5.41]
14.0
[0.55]
17.4
[0.69]
21.8
[0.86]
27.8
[1.09]
34.8
[1.37]
43.5
[1.71]
DKMH.PK.110.B5.02 520L0262
95
OMEW
Technical Information
Dimensions US version
DIMENSIONS
Type
OMEW 100
OMEW 125
OMEW 160
OMEW 200
OMEW 250
OMEW 315
mm mm
L
[in] 1 [in]
107.9
[4.25]
111.3
[4.38]
115.7
[4.56]
121.7
[4.79]
128.7
[5.07]
137.4
[5.41]
14.0
[0.55]
17.4
[0.69]
21.8
[0.86]
27.8
[1.09]
34.8
[1.37]
43.5
[1.71]
D: 78 - 14 UNF;
16.7 mm [0.66 in] deep
G: Tapered shaft 1 1/4 in
(ISO/R775)
J: Nut 1 - 20 UNEF
Across flats 1 7/16
Tightening torque:
200 10 Nm [1770 85 lbfin]
K: Taper 1:8
M: Parallel key
5
/16 5/16 1 1/4
SAEJ 501
96
DKMH.PK.110.B5.02 520L0262
Code no
Weight
kg
[lb]
Code no
Weight
kg
[lb]
Code no
Weight
kg
[lb]
151-0208
151-0242
151-0243
151-0244
151-0245
151-0246
151-0247
151-0248
151-0265
151-0266
151-0267
151-0268
151-0269
151-0270
151-0271
151-0300
151-0301
151-0302
151-0303
151-0304
151-0305
151-0306
151-0307
151-0308
151-0310
151-0311
151-0312
151-0313
151-0314
151-0315
151-0316
151-0317
151-0318
151-0330
151-0331
151-0332
151-0333
151-0334
151-0335
151-0336
151-0337
151-0338
151-0340
151-0341
151-0342
151-0400
151-0401
151-0402
151-0403
7.2
6.9
7.0
7.5
8.0
9.0
8.5
6.7
6.7
6.9
7.0
7.5
8.0
9.0
8.5
5.6
5.7
5.9
6.0
6.2
6.4
6.6
6.9
7.4
5.6
5.7
5.9
6.0
6.2
6.4
6.6
6.9
7.4
5.6
5.7
5.9
6.0
6.2
6.4
6.6
6.9
7.4
5.5
5.5
5.6
6.7
6.9
7.0
7.2
151-0404
151-0405
151-0406
151-0407
151-0408
151-0410
151-0411
151-0412
151-0413
151-0414
151-0415
151-0416
151-0417
151-0418
151-0420
151-0421
151-0422
151-0423
151-0424
151-0425
151-0426
151-0427
151-0428
151-0600
151-0601
151-0602
151-0603
151-0604
151-0605
151-0606
151-0607
151-0608
151-0610
151-0611
151-0612
151-0613
151-0614
151-0615
151-0616
151-0617
151-0618
151-0630
151-0631
151-0632
151-0633
151-0634
151-0635
151-0636
151-0637
7.5
8.0
8.5
9.0
9.5
6.7
6.9
7.0
7.2
7.5
8.0
8.5
9.0
9.5
6.7
6.9
7.0
7.2
7.5
8.0
8.5
9.0
9.5
5.6
5.7
5.9
6.0
6.2
6.4
6.6
6.9
7.4
5.6
5.7
5.9
6.0
6.2
6.4
6.6
6.9
7.4
5.6
5.7
5.9
6.0
6.2
6.4
6.6
6.9
151-0638
151-0640
151-0641
151-0642
151-0700
151-0701
151-0702
151-0703
151-0704
151-0705
151-0706
151-0707
151-0708
151-0710
151-0711
151-0712
151-0713
151-0714
151-0715
151-0716
151-0717
151-0718
151-0720
151-0721
151-0722
151-0723
151-0724
151-0725
151-0726
151-0727
151-0728
151-1208
151-1209
151-1210
151-1211
151-1212
151-1213
151-1214
151-1215
151-1217
151-1231
151-1232
151-1233
151-1234
151-1235
151-1236
151-1237
151-1238
151-1243
7.4
5.5
5.5
5.6
6.7
6.9
7.0
7.2
7.5
8.0
8.5
9.0
9.5
6.7
6.9
7.0
7.2
7.5
8.0
8.5
9.0
9.5
6.7
6.9
7.0
7.2
7.5
8.0
8.5
9.0
9.5
5.6
5.7
5.9
6.2
6.4
6.6
6.9
7.4
6.0
6.7
6.9
7.0
7.5
8.0
8.5
9.0
7.2
9.5
DKMH.PK.110.B5.02 520L0262
15.9
15.2
15.4
16.5
17.6
19.8
18.7
14.8
14.8
15.2
15.4
16.5
17.6
19.8
18.7
12.3
12.6
13.0
13.2
13.7
14.1
14.6
15.2
16.3
12.3
12.6
13.0
13.2
13.7
14.1
14.6
15.2
16.3
12.3
12.6
13.0
13.2
13.7
14.1
14.6
15.2
16.3
12.1
12.1
12.3
14.8
15.2
15.4
15.9
16.5
17.6
18.7
19.8
20.9
14.8
15.2
15.4
15.9
16.5
17.6
18.7
19.8
20.9
14.8
15.2
15.4
15.9
16.5
17.6
18.7
19.8
20.9
12.3
12.6
13.0
13.2
13.7
14.1
14.6
15.2
16.3
12.3
12.6
13.0
13.2
13.7
14.1
14.6
15.2
16.3
12.3
12.6
13.0
13.2
13.7
14.1
14.6
15.2
16.3
12.1
12.1
12.3
14.8
15.2
15.4
15.9
16.5
17.6
18.7
19.8
20.9
14.8
15.2
15.4
15.9
16.5
17.6
18.7
19.8
20.9
14.8
15.2
15.4
15.9
16.5
17.6
18.7
19.8
20.9
12.3
12.6
13.0
13.7
14.1
14.6
15.2
16.3
13.2
14.8
15.2
15.4
16.5
17.6
18.7
19.8
15.9
20.9
97
98
Code no
Weight
kg
[lb]
Code no
151-5001
151-5002
151-5003
151-5004
151-5005
151-5006
151-5007
151-5008
151-5009
151-5174
151-5191
151-5192
151-5193
151-5194
151-5195
151-5196
151-5197
151-5198
151-5199
151-5211
151-5212
151-5213
151-5214
151-5215
151-5216
151-5217
151-5218
151-5219
151-5301
151-5302
151-5303
151-5304
151-5305
151-5306
151-5307
151-5308
151-5309
151-6000
151-6001
151-6002
151-6003
151-6004
151-6005
151-6006
151-6007
151-6008
151-6010
151-6011
151-6012
5.6
5.7
5.9
6.0
6.2
6.4
6.6
6.9
7.4
5.4
6.1
6.2
6.4
6.5
6.7
6.9
7.1
7.4
7.9
5.5
5.6
5.8
5.9
6.1
6.3
6.5
6.8
7.3
5.5
5.6
5.8
5.9
6.1
6.3
6.5
6.8
7.3
6.7
6.9
7.0
7.2
7.5
8.0
8.5
9.0
9.5
6.7
6.9
7.0
151-6013
151-6014
151-6015
151-6016
151-6017
151-6018
151-6110
151-6111
151-6112
151-6113
151-6114
151-6115
151-6116
151-6117
151-6118
151-6190
151-6191
151-6192
151-6193
151-6194
151-6195
151-6196
151-6197
151-6198
151-6210
151-6211
151-6212
151-6213
151-6214
151-6215
151-6216
151-6217
151-6218
151-6294
151-6295
151-6296
151-6300
151-6301
151-6302
151-6303
151-6304
151-6305
151-6306
151-6307
151-6308
151-6430
151-6431
151-6432
151-6433
DKMH.PK.110.B5.02 520L0262
12.3
12.6
13.0
13.2
13.7
14.1
14.6
15.2
16.3
11.9
13.4
13.7
14.1
14.3
14.8
15.2
15.7
16.3
17.4
12.1
12.3
12.8
13.0
13.4
13.9
14.3
15.0
16.1
12.1
12.3
12.8
13.0
13.4
13.9
14.3
15.0
16.1
14.8
15.2
15.4
15.9
16.5
17.6
18.7
19.8
20.9
14.8
15.2
15.4
Weight
kg
[lb]
7.2
7.5
8.0
8.5
9.0
9.5
6.7
6.9
7.0
7.2
7.5
8.0
8.5
9.0
9.5
7.3
7.5
7.6
7.8
8.1
8.6
9.1
9.6
10.1
6.7
6.9
7.0
7.2
7.5
8.0
8.5
9.0
9.5
9.5
7.2
9.5
9.0
9.4
9.5
9.7
10.0
10.5
11.0
11.5
12.0
9.0
9.4
9.5
9.7
15.9
16.5
17.6
18.7
19.8
20.9
14.8
15.2
15.4
15.9
16.5
17.6
18.7
19.8
20.9
16.1
16.5
16.8
17.2
17.9
19.0
20.1
21.2
22.3
14.8
15.2
15.4
15.9
16.5
17.6
18.7
19.8
20.9
20.9
15.9
20.9
19.8
20.7
20.9
21.4
22.1
23.1
24.3
25.4
26.5
19.8
20.7
20.9
21.4
Code no
151-6434
151-6435
151-6436
151-6437
151-6438
151-7021
151-7022
151-7023
151-7024
151-7025
151-7026
151-7027
151-7028
151-7029
151-7041
151-7042
151-7043
151-7044
151-7045
151-7046
151-7047
151-7048
151-7049
151-7061
151-7062
151-7063
151-7065
151-7066
151-7067
151-7068
151-7069
151-7080
151-7081
151-7082
151-7101
151-7102
151-7103
151-7104
151-7105
151-7106
151-7107
151-7108
151-7109
151-7240
151-7241
151-7242
151-7243
151-7244
151-7245
Weight
kg
[lb]
10.0
10.5
11.0
11.5
12.0
5.0
5.1
5.3
5.4
5.6
5.8
6.0
6.3
6.8
5.6
5.7
5.9
5.4
6.2
6.4
6.6
6.9
7.4
5.0
5.1
5.3
5.6
5.8
6.0
6.3
6.8
5.4
5.4
5.6
5.5
5.6
5.8
5.9
6.1
6.3
6.5
6.8
7.3
6.7
6.9
7.0
7.2
7.5
8.0
22.1
23.1
24.3
25.4
26.5
11.0
11.2
11.7
11.9
12.3
12.8
13.2
13.9
15.0
12.3
12.6
13.0
11.9
13.7
14.1
14.6
15.2
16.3
11.0
11.2
11.7
12.3
12.8
13.2
13.9
15.0
12.0
12.0
12.3
12.1
12.3
12.8
13.0
13.4
13.9
14.3
15.0
16.1
14.8
15.2
15.4
15.9
16.5
17.6
Code no
151-7246
151-7247
151-7248
151-7250
151-7251
151-7252
151-7253
151-7254
151-7255
151-7256
151-7257
151-7258
151-7260
151-7261
151-7262
151-7263
151-7264
151-7265
151-7266
151-7267
151-7269
151H1002
151H1003
151H1004
151H1005
151H1006
151H1012
151H1013
151H1014
151H1015
151H1016
151H1022
151H1023
151H1024
151H1025
151H1026
151H1034
151H1035
151H1036
151H1042
151H1043
151H1044
151H1045
151H1046
151H1052
151H1053
151H1054
151H1055
151H1056
Weight
kg
[lb]
8.5
9.0
9.5
6.7
6.9
7.0
7.2
7.5
8.0
8.5
9.0
9.5
6.1
6.3
6.4
6.6
6.9
7.4
7.9
8.4
8.9
10.5
11.0
11.5
12.3
13.0
10.5
11.0
11.5
12.3
13.0
10.5
11.0
11.5
12.3
13.0
11.5
12.3
13.0
10.5
11.0
11.5
12.3
13.0
10.5
11.0
11.5
12.3
13.0
DKMH.PK.110.B5.02 520L0262
18.7
19.8
20.9
14.8
15.2
15.4
15.9
16.5
17.6
18.7
19.8
20.9
13.4
13.9
14.1
14.6
15.2
16.3
17.4
18.5
19.6
23.1
24.3
25.4
27.1
28.7
23.1
24.3
25.4
27.1
28.7
23.1
24.3
25.4
27.1
28.7
25.4
27.1
28.7
23.1
24.3
25.4
27.1
28.7
23.1
24.3
25.4
27.1
28.7
Code no
151H1080
151H1081
151H1082
151H1083
151H1084
151H2002
151H2003
151H2004
151H2005
151H2006
151H2007
151H2011
151H2012
151H2013
151H2014
151H2015
151H2016
151H3002
151H3003
151H3004
151H3005
151H3006
151H3007
151H3011
151H3012
151H3013
151H3014
151H3015
151H3016
Weight
kg
[lb]
10.5
13.0
11.0
11.5
12.3
9.3
9.5
9.8
10.3
10.8
11.3
9.3
9.5
9.8
10.3
10.8
11.3
9.3
9.5
9.8
10.3
10.8
11.3
9.3
9.5
9.8
10.3
10.8
11.3
23.1
28.7
24.3
25.4
27.1
20.5
20.9
21.6
22.7
23.8
24.9
20.5
20.9
21.6
22.7
23.8
24.9
20.5
20.9
21.6
22.7
23.8
24.9
20.5
20.9
21.6
22.7
23.8
24.9
99
OUR PRODUCTS
Hydrostatic transmissions
Hydraulic power steering
Electro-hydraulic power steering
Electric power steering
Closed and open circuit axial piston
pumps and motors
Gear pumps and motors
Bent axis motors
Radial piston motors
Orbital motors
Transit mixer drives
Planetary compact gears
Proportional valves
Directional spool valves
Cartridge valves
Hydraulic integrated circuits
Hydrostatic transaxles
Integrated systems
Fan drive systems
Electrohydraulic controls
Digital electronics and software
Battery powered inverter
Sensors
www.sauer-danfoss.com