Beruflich Dokumente
Kultur Dokumente
IT
Industrial
Contents
Page
Application characteristics
Technically, the permanent magnet motor could be
used in any application up to about 850 r/min. However, not all applications may be economic.
Permanent magnet motor solution can typically
replace:
A traditional AC motor and gearbox with frequency
converter.
A traditional low speed AC motor, typically 10 to 16pole or slower with frequency converter.
A DC motor with DC drive and gearbox.
The permanent magnet motor is ideal in the following cases:
Where the application is speed controlled, for instance with a frequency converter.
Where the nominal load speed, for example the
gearbox output speed, is 100 to 850 r/min or ideally 300 to 600 r/min.
Where the nominal load torque is between 1000
and 50 000 Nm *).
Where the required short-time overloadability is
limited to 120 - 150 %.
The greatest savings are achieved if the current
speed reduction system is expensive or otherwise
problematic.
P [kW] x 9550
load r/min
Example:
Motor 160 kW, max. motor speed 1500 r/min. Gearbox
with i = 5
Gearbox output speed (= load speed) = 1500 / 5 = 300
r/min
T=
160 x 9550
= 5093 Nm
300
See 'Motor characteristics section 4. Motor selection
example'.
Motor characteristics
The rotor magnetization is achieved by the permanent
magnets installed inside the rotor. This means the
amount of magnetizing current drawn from the supply
network is minimal. For this reason, the power factor
of these motors is considerably higher compared to
squirrel cage motors with the same nominal speeds. In
practice, this means smaller frequency converters and
supply units.
1. Loadability
Motors with separate cooling (IC 416) or liquid cooling can deliver full torque continuously at any speed
between zero and nominal speed (nn). The continuous
output torque of self-cooled (IC 411) motors must be
derated according to the applicable speed range. Note
that the nominal torque of a self-cooled (IC 411) motor
is not equal to the nominal torque of the same motor
with separate cooling (IC 416). Derating factors can be
found in Figure 1. Above nominal speed all motors can
deliver constant power (CP) up to 1.2 times nn.
This catalogue includes all available M3BJ and M3LJ
type motors. A greater speed and output range is available in the AMZ series of motors. The types listed
in this catalogue represent the torque range for each
frame size.
2. Speed Range
Generally the speed range of these motors is from zero
to 1.2 times the nominal speed. The voltage, which is
induced by the permanent magnets to the stator windings, is proportional to the rotational speed. At speeds
higher than 1.2 times nn, the voltage may be too high for
the insulation of the motor and the supply system, as
well as for the frequency converter. In some cases the
Figure 1. Permanent magnet synchronous motor loadability
with ACS 600 and ACS 800 Frequency Converter.
120%
Torque / TN
100%
80%
60%
40%
20%
0%
0.00
0.20
0.40
0.60
0.80
1.00
1.20
1.40
5. Insulation protection
Example
Network voltage: 500 V
Load: Constant torque 8000 Nm, 100-400 r/min, 335 kW
at 400 r/min
Cooling: IC 416 cooling
In the 500 V section there are 375 r/min and 433 r/min
motor base speeds.
In the case of the 375 r/min motor base speed, the
motor's base speed is below the base speed of the load
and the motor selection is based on power as the motor
is working on the constant power range. The M3BJ
400LC / 3GBJ406530-ADG183706 motor can deliver
366 kW between 375 r/min and 450 r/min and 9309 Nm
between 0-375 r/min. It meets the application requirements.
In the case of 433 r/min base speed, the motors base
speed is above the loads base speed and the motor
selection is based on torque as the motor is working on
its constant torque range throughout the loads speed
range. The M3BJ 400LC / 3GBJ406530-ADG183708
can deliver 8906 Nm between 0 - 433 r/min. Also this
motor meets the application requirements.
However the 375 r/min motor needs less current as it
has reached the eld weakening point and full inverter
output voltage. This minimizes the inverter size and
optimizes the drive system economically.
The 280 to 400 size motors are equipped with reinforced insulation as standard, thus dU/dt-lter is needed
only above 600 V.
The 500 to 560 size motor are made with form wound
windings with Micadur Compact Industry Insulation
system (class F). It has a sufcient insulation level for
a IGBT converter even without output chokes or dU/dt
lters. For more information, please see the brochure
'Micadur Compact Industry, Insulation System for Rotating Electrical Machines' (code 3BFP 001 980 R0101
REV B 06/2003).
6. Bearing currents
Bearing voltages and currents must be avoided in all
motors. When using ABB IGBT frequency converters
properly dimensioned lters at the converter output
must be used according to the instructions in gure
2. (For other alternatives and converter types, please
contact ABB)
When ordering, clearly state the alternative to be used.
All motors listed in this catalogue have insulated bearings or bearing systems at the non-drive end as standard.
For more information about bearing currents and voltages, please consult ABB document 3GZF500930-8 or
contact ABB.
UN 500 V
Standard motor
Standard motor
UN 600 V
Standard motor
+ Common mode lters
Standard motor
Standard motor
+ Common mode lters
UN 690 V
Standard motor
+dU/dt lter (reactor)
Standard motor
+ dU/dt lter (reactor)
+ Common mode lters
dU/dt lter
These lters are series reactors, which decrease the rate of change of the phase and main voltages and thus reduce voltages and reduce voltage
stress in the windings. dU/dt lters also decrease common mode currents and the risk of bearing currents. They are designed to limit the dU/dt
rate of the main voltage at motor terminals to approx. 1 kV/s.
Common mode lters
Common mode lters consist of toroidal cores installed around motor cables or onto the busbars inside frequency converter. These lters
reduce common mode currents in VSD applications and thus decrease the risk of bearing currents. Common mode lters do not signicantly
affect thephase or main voltages on motor terminals. For more information and product codes, please contact ABB.
Mechanical design
Stator frame
Air cooled motors are constructed with cast iron frame,
feet and bearing housing.
Drain holes
All motors are fitted with drain holes and closable plugs.
The plugs are open on delivery. When mounting the
motor, ensure that the drain holes face downwards.
closed
open
open
10
The terminal box is equipped with cable glands or cable boxes as standard.
Terminal
box
opening
Motor
size
Variant
code
Terminal
box
Flange
or adapter
Cable
diameter
mm
Max.
conn.
cable
area
280SMB
315SMC
315MLA
315LKB
315LKC
355SMB
355MLB
355LKB
400LC
705
705
705
705
705
705
705
705
705
210
370
370
370
370
370
370
370
370
260/150
470/270
470/270
470/270
470/270
640/370
640/370
640/370
640/370
C
D
D
D
D
D
D
D
D
3GZF294730-748
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-753
2x 3GZF294730-612
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2xM50x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2x 26-35
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x150
2x240
2x240
2x240
2x240
2x240
2x240
2x240
2x240
280SMB
315SMC
315MLA
315LKB
315LKC
355SMB
355MLB
355LKB
400LC
706
706
706
706
706
706
706
706
706
210
370
370
370
370
370
370
370
370
260/150
470/270
470/270
470/270
470/270
640/370
640/370
640/370
640/370
C
D
D
D
D
D
D
D
D
3GZF294730-749
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-753
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x150
2x240
2x240
2x240
2x240
2x240
2x240
2x240
2x240
280SMB
315SMC
315MLA
315LKB
315LKC
355SMB
355MLB
355LKB
400LC
707
707
707
707
707
707
707
707
707
210
370
370
370
370
370
370
370
750
260/150
470/270
470/270
470/270
470/270
640/370
640/370
640/370
950/550
C
D
D
D
D
D
D
D
E
3GZF294730-749
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-944
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
3GZF294730-301
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x 48-60
2x150
2x240
2x240
2x240
2x240
2x240
2x240
2x240
4x240
280SMB
315SMC
315MLA
315LKB
315LKC
355SMB
355MLB
355LKB
400LC
708
708
708
708
708
708
708
708
708
210
370
370
370
370
370
750
750
750
260/150
470/270
470/270
470/270
470/270
640/370
950/550
950/550
950/550
C
D
D
D
D
D
E
E
E
3GZF294730-749
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-753
3GZF294730-944
3GZF294730-944
3GZF294730-945
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
2x 3GZF294730-613
3GZF294730-301
3GZF294730-301
2x 3GZF294730-301
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2xM63x1.5
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x 32-49
2x 48-60
2x 48-60
2x(2x 48-60)
2x150
2x240
2x240
2x240
2x240
2x240
4x240
4x240
4x240
Cable box
or cable gland
Gland
thread
11
Flange
3GZF294730-749 (M3BP 280)
3GZF294730-753 (M3BP 315)
Cable box
3GZF294730-301
Cable box
3GZF294730-501
12
Inlet
62
193
62
193
M8
100
300
80
292
M10
115
370
100
360
M12
Horizontal machine
Cable bushings
FL33 opening
Roxtec
Number
the cable
of cables
70 - 98
50 - 70
3-6
32 - 50
7-8
22 - 32
3-6
32 - 50
9- 12
22 - 32
3-phase
1-phase
Undrilled plate
13
Bearings
The horizontally mounted motors are provided with
single-row deep groove ball bearings as listed in the
table.
Motor
Mounting
size
Standard design
Bearings
D-end
Horizontal
6316/C3
6316M/C3 VL0241
3151)
Horizontal
6319/C3
6316M/C3 VL0241
1)
355
Horizontal
6322/C3
6316M/C3 VL0241
4001)
Horizontal
6324/C3
6319M/C3 VL0241
500
Horizontal
6330/C3
6330/C3
500
Vertical
6330/C3
7330 BM
560
Horizontal
6338/C3
6338/C3
560
Vertical
6338/C3
7338 BM
280
N-end
1)
1)
Bearing seals
The size and type of suitable seals are in accordance
with the table below:
Motor size
280
Standard design
D-end
N-end
315
355
400
500 - 560
Labyrinth seal
Labyrinth seal
Labyrinth seal
Alternative design
D-end
N-end
Labyrinth seal
Labyrinth seal
V-ring
Radial seal
14
N-end
Axially free
Bearing life
The nominal life L10h of a bearing is defined according
to ISO as the number of operating hours achieved or
exceeded by 90% of identical bearings in a large test
series under certain specified conditions. 50% of the tested bearings achieve at least five times the L10h life. The
values in the table are calculated without any external
forces on motor bearings.
Motor size
Mounting
L10h [hours]
280 to 400
Horizontal
80000
280 to 400
Vertical
On request
500
Horizontal
58000
500
Vertical
63000
560
Horizontal
42000
560
Vertical
50000
Lubrication
Permanent magnet motors have grease valve lubrication for lubrication in service. The lubrication intervals
and grease quantity are stated in the maintenance
instructions, which are delivered with the motor. If a
motor is equipped with a lubrication instruction plate,
the instructions on the plate should followed.
Pulley diameter
When the desired bearing life has been determined, the minimum permissible pulley diameter can be calculated using FR, as follows:
D=
1.9 107 K P
n FR
where:
D = diameter of pulley, mm
P = power requirement, kW
n = motor speed, r/min
K = belt tension factor, dependent on belt type
and type of duty. A common value for
V-belts is 2.5.
FR = permissible radial force
15
Length of
Ball bearings
Length of
shaft
shaft
Motor
size
extension
E (mm)
40,000 hours
FXmax(N)
Motor
size
280 SM_
140
5000
315 SM_
170
5000
315 ML_
170
5000
315 LK_
170
5000
355 SM_
210
5000
355 ML_
210
5000
355 LK_
210
5000
400 L_
210
5000
16
30,000 hours
extension
E (mm)
300 r/min
FXmax(N)
600 r/min
FXmax(N)
850 r/min
FXmax(N)
500
250
12000
6000
4000
560
300
13600
5600
3000
Rating plates
Motor sizes 280 to 400
17
Ordering information
When placing an order, please state the following
minimum data in the order, as in the example.
Motor type
M3BJ 280 SMB
Pole number
12
Mounting arrangement (IM code) IM B3 (IM 1001)
Product code if stated
3GBJ316 220-ADG 705
More variant codes if needed
Motor size
A
D, E,
F,
5-6 7
8 9 10 11 12 13 14
15
A Motor type
B Motor size
C Product code
D Mounting arrangement code
E Voltage and frequency code
F Generation code
G Variant codes
Position 13
Voltage and frequency code
Network voltage 400 V to 690 V
Position 14
Generation code
C = Liquid cooled motor
G = Air cooled motor
Positions 5 and 6
IEC-frame
28 =
280
31 =
315
35 =
355
40 =
400
Position 15
Variant codes
705 =
220 r/min at 400 VD/690 VY
706 =
300 r/min at 400 VD/690 VY
707 =
430 r/min at 400 VD/690 VY
708 =
600 r/min at 400 VD/690 VY
Base speed and output depends on the network voltage.
See technical data for values at different network voltages.
Position 7
Speed (Pole pairs)
6 = 12 poles
Position 8 to 10
Serial number
Position 11
- (dash)
Position 12
Mounting arrangement
A = Foot-mounted, top-mounted terminal box
B = Flange-mounted motors available on request
3 4 5
Position 6
IC/IP combination
J = water jacket IC 71W/IP(55, 56), welded steel frame
R = total enclosed fan cool IC 41(1,6,7)/ IP(55, 56), cast iron
frame
Position 7
Bearing type
A = antifriction bearings
Position 8
Type of excitation
M = permanent magnet rotor
Product code1)
Current
IN
A
Efficiency
Full load2)
%
Torque
TN
Nm
Power
factor
cos
Torque
TN4)
Moment
of inertia
J=1/4GD2
kgm2
Tmax
Maximum
speed,
nmax
r/min
Weight
approx.
kg
17
23
36
45
58
63
86
100
126
174
237
306
386
479
576
667
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0500LR10 _AM
AMZ 0560LQ10 _AM
AMZ 0560LS10 _AM
AMZ 0560LU10 _AM
3G_J286220-_D_183705
3G_J316230-_D_183705
3G_J316410-_D_183705
3G_J316820-_D_183705
3G_J316830-_D_183705
3G_J356220-_D_183705
3G_J356420-_D_183705
3G_J356820-_D_183705
3G_J406530-_D_183705
34
44
68
84
107
114
155
179
221
310
414
533
679
832
1003
1149
81.1
85.4
86.7
87.5
89.2
88.7
89.2
90.0
91.0
93.3
93.9
94.4
94.7
95.1
95.4
95.4
1257
1720
2695
3416
4327
4727
6458
7539
9469
13084
17822
23010
29026
36019
43313
50156
0.94
0.95
0.95
0.97
0.95
0.97
0.97
0.97
0.98
0.93
0.95
0.94
0.93
0.94
0.93
0.94
1.0
1.1
1.1
1.1
1.1
1.2
1.2
1.2
1.1
1.2
1.2
1.2
1.2
1.3
1.4
1.3
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
135
224
265
306
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
7580
10490
11480
12470
3G_J286220-_D_183706
3G_J316230-_D_183706
3G_J316410-_D_183706
3G_J316820-_D_183706
3G_J316830-_D_183706
3G_J356220-_D_183706
3G_J356420-_D_183706
3G_J356820-_D_183706
3G_J406530-_D_183706
46
68
95
116
160
152
203
230
299
418
576
754
926
1134
1300
1516
85.6
87.3
88.9
90.8
90.8
91.2
92.0
92.9
93.2
94.7
95.3
95.6
95.9
96.2
96.3
96.4
1280
1980
2835
3496
4774
4760
6360
7154
9545
13138
18272
23847
29202
36213
42230
49296
0.93
0.94
0.95
0.94
0.93
0.97
0.97
0.95
0.97
0.93
0.94
0.93
0.92
0.93
0.95
0.95
1.0
1.0
1.0
1.1
1.1
1.2
1.2
1.3
1.1
1.2
1.2
1.2
1.3
1.4
1.3
1.3
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
135
224
265
306
208
208
208
208
208
208
208
208
208
208
208
208
208
208
208
208
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
7580
10490
11480
12470
3G_J286220-_D_183705
3G_J316230-_D_183705
3G_J316410-_D_183705
3G_J316820-_D_183705
3G_J316830-_D_183705
3G_J356220-_D_183705
3G_J356420-_D_183705
3G_J356820-_D_183705
3G_J406530-_D_183705
58
75
115
143
181
192
263
304
375
534
747
933
1147
1518
1826
88.0
90.5
91.4
91.8
92.7
92.6
92.9
93.3
94.1
95.6
96.1
96.3
96.6
96.8
96.9
1303
1743
2734
3472
4350
4769
6501
7591
9547
13240
18579
23484
28997
38895
46578
0.92
0.93
0.93
0.95
0.93
0.96
0.96
0.96
0.97
0.93
0.93
0.93
0.94
0.95
0.94
1.0
1.1
1.1
1.1
1.1
1.2
1.2
1.2
1.1
1.2
1.3
1.2
1.3
1.3
1.3
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
183
245
286
264
264
264
264
264
264
264
264
264
264
264
264
264
264
264
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
9500
10990
11980
nn = 173 r/min
23
36
51
63
87
86
115
130
173
238
331
432
529
656
765
893
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0500LR10 _AM
AMZ 0560LQ10 _AM
AMZ 0560LS10 _AM
AMZ 0560LU10 _AM
nn = 220 r/min
30
40
63
80
100
110
150
175
220
305
428
541
668
896
1073
1)
2)
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0560LL10 _AM
AMZ 0560LR10 _AM
AMZ 0560LT10 _AM
See ordering information - section for details on motor type and product
code, variant code 183 used only with air cooled, IC 416 motors
Separate cooling fan power not considered in efficiency value
3)
4)
Output values and more base speeds for IEC 500 and 560 sizes on request
Tmax/TN value represents maximum short time overloadability with inverter
supply. This does not represent the pull-out torque value according to IEC.
19
400 V
nn = 127 r/min
Product code1)
Current
IN
A
Efficiency
Full load2)
%
Torque
TN
Nm
Power
factor
cos
Torque
TN4)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Tmax
Weight
approx.
kg
nn = 248 r/min
400 V
32
46
72
87
116
116
161
193
245
332
481
619
754
1036
1320
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0560LL10 _AM
AMZ 0560LR10 _AM
AMZ 0560LU10 _AM
3G_J286220-_D_183707
3G_J316230-_D_183707
3G_J316410-_D_183707
3G_J316820-_D_183707
3G_J316830-_D_183707
3G_J356220-_D_183707
3G_J356420-_D_183707
3G_J356820-_D_183707
3G_J406530-_D_183707
59
83
131
154
205
197
284
331
436
571
834
1071
1297
1811
2267
89.5
91.1
92.2
93.1
93.2
93.1
94.1
94.4
95.1
96.0
96.4
96.6
96.9
97.1
97.2
1216
1772
2776
3331
4442
4441
6208
7433
9429
12785
18522
23836
29035
39894
50831
0.93
0.95
0.93
0.94
0.94
0.98
0.94
0.97
0.92
0.94
0.93
0.93
0.93
0.93
0.93
1.0
1.1
1.1
1.2
1.1
1.2
1.3
1.3
1.3
1.2
1.2
1.3
1.4
1.4
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
183
245
306
298
298
298
298
298
298
298
298
298
298
298
298
298
298
298
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
9500
10990
12470
3G_J286220-_D_183706
3G_J316230-_D_183706
3G_J316410-_D_183706
3G_J316820-_D_183706
3G_J316830-_D_183706
3G_J356220-_D_183706
3G_J356420-_D_183706
3G_J356820-_D_183706
3G_J406530-_D_183706
77
116
162
197
271
258
344
393
508
739
1227
1517
2270
90.5
91.7
92.8
93.8
93.8
94.0
94.5
94.9
95.3
96.5
97.0
97.2
97.4
1303
2006
2864
3500
4786
4769
6355
7155
9543
13275
22952
28491
42720
0.91
0.92
0.94
0.93
0.92
0.96
0.96
0.94
0.97
0.92
0.94
0.94
0.94
1.0
1.0
1.0
1.1
1.1
1.2
1.2
1.3
1.1
1.3
1.3
1.3
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
113
183
265
360
360
360
360
360
360
360
360
360
360
360
360
360
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6800
9500
11480
3G_J286220-_D_183708
3G_J316230-_D_183708
3G_J316410-_D_183708
3G_J316820-_D_183708
3G_J316830-_D_183708
3G_J356220-_D_183708
3G_J356420-_D_183708
3G_J356820-_D_183708
3G_J406530-_D_183708
87
114
161
206
283
276
370
406
543
831
1490
1841
2256
2474
91.8
93.2
93.9
94.7
94.3
94.7
95.2
95.3
96.0
96.8
97.3
97.4
97.6
97.9
1274
1750
2547
3180
4411
4437
5966
6767
8908
13249
23847
29147
36130
41485
0.91
0.93
0.95
0.92
0.94
0.95
0.96
0.99
0.97
0.93
0.92
0.92
0.93
0.96
1.0
1.1
1.1
1.3
1.0
1.2
1.3
1.3
1.2
1.3
1.3
1.3
1.4
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
113
135
224
306
415
415
415
415
415
415
415
415
415
415
415
415
415
415
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6800
7580
10490
12470
nn = 300 r/min
41
63
90
110
150
150
200
225
300
417
721
895
1342
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LN10 _AM
AMZ 0560LL10 _AM
AMZ 0560LS10 _AM
nn = 346 r/min
46
64
92
115
160
161
216
246
323
480
864
1056
1309
1503
1)
2)
20
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LN10 _AM
AMZ 0500LR10 _AM
AMZ 0560LQ10 _AM
AMZ 0560LU10 _AM
See ordering information - section for details on motor type and product
code, variant code 183 used only with air cooled, IC 416 motors
Separate cooling fan power not considered in efficiency value
3)
4)
Output values and more base speeds for IEC 500 and 560 sizes on request
Tmax/TN value represents maximum short time overloadability with inverter
supply. This does not represent the pull-out torque value according to IEC.
Product code1)
Current
IN
A
Efficiency
Full load2)
%
Torque
TN
Nm
Power
factor
cos
Torque
TN4)
Moment
of inertia
J=1/4GD2
kgm2
Tmax
Maximum
speed,
nmax
r/min
Weight
approx.
kg
55
80
125
150
200
200
280
335
423
596
834
1071
1298
1502
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0560LL10 _AM
AMZ 0560LR10 _AM
3G_J286220-_D_183707
3G_J316230-_D_183707
3G_J316410-_D_183707
3G_J316820-_D_183707
3G_J316830-_D_183707
3G_J356220-_D_183707
3G_J356420-_D_183707
3G_J356820-_D_183707
3G_J406530-_D_183707
101
141
223
263
351
335
487
567
748
1053
1472
1846
2250
2495
92.7
93.8
94.5
95.0
95.1
95.1
95.6
95.8
96.4
97.2
97.4
97.5
97.7
98.0
1222
1776
2775
3329
4440
4440
6207
7434
9384
13237
18523
23786
28828
33358
0.92
0.94
0.93
0.94
0.94
0.98
0.94
0.96
0.92
0.92
0.92
0.92
0.93
0.95
1.0
1.1
1.1
1.2
1.1
1.2
1.3
1.3
1.3
1.3
1.3
1.3
1.4
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
183
245
516
516
516
516
516
516
516
516
516
516
516
516
516
516
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
9500
10990
3G_J286220-_D_183708
3G_J316230-_D_183708
3G_J316410-_D_183708
3G_J316820-_D_183708
3G_J316830-_D_183708
3G_J356220-_D_183708
3G_J356420-_D_183708
3G_J356820-_D_183708
3G_J406530-_D_183708
148
195
276
355
427
424
638
696
934
94.1
95.1
95.5
95.8
95.9
96.0
96.2
96.2
96.9
1274
1750
2546
3179
3977
3974
5963
6763
8904
0.90
0.93
0.95
0.92
0.95
0.96
0.95
0.99
0.97
1.0
1.1
1.1
1.3
1.2
1.4
1.3
1.3
1.2
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
720
720
720
720
720
720
720
720
720
660
890
1125
1430
1605
1780
2210
2690
3280
nn = 600 r/min
80
110
160
200
250
250
375
425
560
3)
3)
1)
2)
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500L_10 _AM
AMZ 0560L_10 _AM
See ordering information - section for details on motor type and product
code, variant code 183 used only with air cooled, IC 416 motors
Separate cooling fan power not considered in efficiency value
3)
4)
Output values and more base speeds for IEC 500 and 560 sizes on request
Tmax/TN value represents maximum short time overloadability with inverter
supply. This does not represent the pull-out torque value according to IEC.
21
400 V
nn = 430 r/min
Product code1)
Current
IN
A
Efficiency
Full load2)
%
Torque
TN
Nm
Power
factor
cos
Torque
TN4)
Moment
of inertia
J=1/4GD2
kgm2
Tmax
Maximum
speed,
nmax
r/min
Weight
approx.
kg
nn = 146 r/min
460 V
20
27
42
53
67
73
99
116
146
201
274
353
446
553
662
770
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0500LR10 _AM
AMZ 0560LQ10 _AM
AMZ 0560LS10 _AM
AMZ 0560LU10 _AM
3G_J286220-_D_183705
3G_J316230-_D_183705
3G_J316410-_D_183705
3G_J316820-_D_183705
3G_J316830-_D_183705
3G_J356220-_D_183705
3G_J356420-_D_183705
3G_J356820-_D_183705
3G_J406530-_D_183705
34
44
68
84
106
113
155
179
221
310
414
532
680
832
1000
1149
83.0
86.9
88.1
88.9
90.2
89.9
90.3
91.0
92.0
94.0
94.6
95.0
95.3
95.6
95.9
95.9
1277
1735
2718
3448
4352
4761
6500
7586
9528
13148
17923
23090
29173
36172
43302
50366
0.94
0.94
0.95
0.96
0.94
0.97
0.97
0.97
0.98
0.93
0.94
0.94
0.93
0.94
0.93
0.94
1.0
1.1
1.1
1.1
1.1
1.2
1.2
1.2
1.1
1.2
1.2
1.2
1.2
1.3
1.4
1.3
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
135
224
265
306
175
175
175
175
175
175
175
175
175
175
175
175
175
175
175
175
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
7580
10490
11480
12470
3G_J286220-_D_183706
3G_J316230-_D_183706
3G_J316410-_D_183706
3G_J316820-_D_183706
3G_J316830-_D_183706
3G_J356220-_D_183706
3G_J356420-_D_183706
3G_J356820-_D_183706
3G_J406530-_D_183706
45
68
95
115
159
151
201
229
297
418
576
751
922
1130
1302
1517
87.1
88.7
90.2
91.7
91.7
92.1
92.7
93.6
93.9
95.2
95.8
96.1
96.3
96.6
96.6
96.7
1292
1996
2854
3502
4788
4775
6363
7151
9548
13197
18332
23851
29178
36184
42423
49478
0.93
0.93
0.94
0.94
0.93
0.97
0.97
0.95
0.97
0.93
0.93
0.93
0.92
0.93
0.95
0.95
1.0
1.0
1.0
1.1
1.1
1.2
1.2
1.3
1.1
1.2
1.2
1.2
1.3
1.4
1.3
1.3
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
135
224
265
306
239
239
239
239
239
239
239
239
239
239
239
239
239
239
239
239
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
7580
10490
11480
12470
3G_J286220-_D_183705
3G_J316230-_D_183705
3G_J316410-_D_183705
3G_J316820-_D_183705
3G_J316830-_D_183705
3G_J356220-_D_183705
3G_J356420-_D_183705
3G_J356820-_D_183705
3G_J406530-_D_183705
57
74
115
141
179
191
261
300
371
532
746
1064
1295
1514
1826
89.1
91.3
92.1
92.6
93.4
93.2
93.5
93.9
94.7
96.1
96.5
96.8
97.0
97.1
97.2
1303
1742
2733
3466
4325
4750
6484
7530
9495
13249
18609
26612
32651
38917
46693
0.92
0.92
0.93
0.95
0.93
0.96
0.96
0.96
0.97
0.93
0.92
0.92
0.93
0.95
0.94
1.0
1.1
1.1
1.1
1.1
1.2
1.2
1.2
1.1
1.3
1.3
1.3
1.4
1.3
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
124
203
245
286
304
304
304
304
304
304
304
304
304
304
304
304
304
304
304
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
7190
10000
10990
11980
nn = 199 r/min
27
42
60
73
100
100
133
149
199
275
382
497
608
754
884
1031
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0500LR10 _AM
AMZ 0560LQ10 _AM
AMZ 0560LS10 _AM
AMZ 0560LU10 _AM
nn = 253 r/min
35
46
72
92
115
126
172
200
252
351
493
705
865
1031
1237
1)
2)
22
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LQ10 _AM
AMZ 0560LN10 _AM
AMZ 0560LR10 _AM
AMZ 0560LT10 _AM
See ordering information - section for details on motor type and product
code, variant code 183 used only with air cooled, IC416 motors
Separate cooling fan power not considered in efficiency value
3)
4)
Output values and more base speeds for IEC 500 and 560 sizes on request
Tmax/TN value represents maximum short time overloadability with inverter
supply. This does not represent the pull-out torque value according to IEC.
Product code1)
Current
IN
A
Efficiency
Full load2)
%
Torque
TN
Nm
Power
factor
cos
Torque
TN4)
Moment
of inertia
J=1/4GD2
kgm2
Tmax
Maximum
speed,
nmax
r/min
Weight
approx.
kg
37
53
83
100
133
133
186
222
282
383
553
712
869
1193
1520
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0560LL10 _AM
AMZ 0560LR10 _AM
AMZ 0560LU10 _AM
3G_J286220-_D_183707
3G_J316230-_D_183707
3G_J316410-_D_183707
3G_J316820-_D_183707
3G_J316830-_D_183707
3G_J356220-_D_183707
3G_J356420-_D_183707
3G_J356820-_D_183707
3G_J406530-_D_183707
59
83
130
153
204
196
283
329
435
570
830
1067
1295
1809
2263
90.6
91.9
92.9
93.8
93.8
93.7
94.6
94.8
95.5
96.3
96.7
96.9
97.1
97.3
97.5
1222
1777
2775
3331
4441
4441
6207
7430
9427
12789
18466
23775
29017
39836
50755
0.93
0.95
0.93
0.94
0.94
0.98
0.94
0.97
0.92
0.94
0.93
0.93
0.93
0.93
0.93
1.0
1.1
1.1
1.2
1.1
1.2
1.3
1.3
1.3
1.2
1.3
1.3
1.4
1.4
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
183
245
306
343
343
343
343
343
343
343
343
343
343
343
343
343
343
343
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
9500
10990
12470
3G_J286220-_D_183706
3G_J316230-_D_183706
3G_J316410-_D_183706
3G_J316820-_D_183706
3G_J316830-_D_183706
3G_J356220-_D_183706
3G_J356420-_D_183706
3G_J356820-_D_183706
3G_J406530-_D_183706
77
115
160
194
267
255
339
382
501
819
1223
1513
2264
91.5
92.5
93.5
94.3
94.3
94.5
94.9
95.3
95.7
97.0
97.3
97.4
97.6
1303
2002
2850
3457
4735
4729
6295
6976
9454
15308
22948
28484
42712
0.91
0.92
0.94
0.93
0.92
0.96
0.96
0.94
0.97
0.94
0.94
0.94
0.94
1.0
1.0
1.0
1.1
1.1
1.2
1.2
1.3
1.1
1.3
1.3
1.4
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
79
113
183
265
414
414
414
414
414
414
414
414
414
414
414
414
414
660
890
1125
1430
1605
1780
2210
2690
3280
5630
6800
9500
11480
3G_J286220-_D_183708
3G_J316230-_D_183708
3G_J316410-_D_183708
3G_J316820-_D_183708
3G_J316830-_D_183708
3G_J356220-_D_183708
3G_J356420-_D_183708
3G_J356820-_D_183708
3G_J406530-_D_183708
86
113
160
205
276
278
370
404
541
829
1484
1839
2253
2472
92.5
93.8
94.3
95.1
94.8
95.2
95.6
95.6
96.3
97.0
97.5
97.6
97.7
98.0
1274
1750
2546
3179
4314
4386
5965
6766
8906
13245
23803
29105
36088
41511
0.90
0.93
0.95
0.92
0.94
0.95
0.96
0.99
0.97
0.92
0.92
0.92
0.93
0.96
1.0
1.1
1.1
1.3
1.1
1.3
1.3
1.3
1.2
1.3
1.3
1.3
1.4
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
113
135
224
306
478
478
478
478
478
478
478
478
478
478
478
478
478
478
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6800
7580
10490
12470
460 V
nn = 286 r/min
nn = 345 r/min
47
72
103
125
171
171
227
252
342
553
829
1029
1543
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LG10 _AM
AMZ 0500LN10 _AM
AMZ 0560LL10 _AM
AMZ 0560LS10 _AM
nn = 398 r/min
53
73
106
133
180
183
249
282
372
552
992
1213
1504
1730
1)
2)
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LN10 _AM
AMZ 0500LR10 _AM
AMZ 0560LQ10 _AM
AMZ 0560LU10 _AM
See ordering information - section for details on motor type and product
code, variant code 183 used only with air cooled, IC416 motors
Separate cooling fan power not considered in efficiency value
3)
4)
Output values and more base speeds for IEC 500 and 560 sizes on request
Tmax/TN value represents maximum short time overloadability with inverter
supply. This does not represent the pull-out torque value according to IEC.
23
Product code1)
Current
IN
A
Efficiency
Full load2)
%
Torque
TN
Nm
Power
factor
cos
Torque
TN4)
Moment
of inertia
J=1/4GD2
kgm2
Tmax
Maximum
speed,
nmax
r/min
Weight
approx.
kg
nn = 495 r/min
460 V
63
91
142
169
225
225
312
372
466
683
955
1227
1488
1730
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0560LL10 _AM
AMZ 0560LR10 _AM
3G_J286220-_D_183707
3G_J316230-_D_183707
3G_J316410-_D_183707
3G_J316820-_D_183707
3G_J316830-_D_183707
3G_J356220-_D_183707
3G_J356420-_D_183707
3G_J356820-_D_183707
3G_J406530-_D_183707
100
139
219
257
341
325
472
545
716
1048
1464
1834
2240
2495
93.4
94.3
95.0
95.4
95.4
95.4
95.9
96.0
96.6
97.4
97.6
97.7
97.8
98.0
1211
1753
2732
3259
4338
4338
6029
7174
8997
13177
18425
23672
28708
33377
0.92
0.94
0.93
0.94
0.94
0.98
0.94
0.96
0.92
0.92
0.92
0.92
0.93
0.95
1.0
1.1
1.1
1.2
1.1
1.2
1.3
1.3
1.3
1.3
1.3
1.3
1.4
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
183
245
594
594
594
594
594
594
594
594
594
594
594
594
594
594
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
9500
10990
3G_J286220-_D_183708
3G_J316230-_D_183708
3G_J316410-_D_183708
3G_J316820-_D_183708
3G_J316830-_D_183708
3G_J356220-_D_183708
3G_J356420-_D_183708
3G_J356820-_D_183708
3G_J406530-_D_183708
145
188
267
340
409
402
610
664
900
94.6
95.3
95.7
96.0
96.1
96.1
96.4
96.4
97.0
1248
1699
2478
3052
3826
3769
5724
6479
8615
0.90
0.93
0.95
0.92
0.96
0.96
0.95
0.99
0.97
1.1
1.2
1.1
1.3
1.2
1.5
1.4
1.3
1.3
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
828
828
828
828
828
828
828
828
828
660
890
1125
1430
1605
1780
2210
2690
3280
nn = 690 r/min
90
123
179
221
277
272
414
468
623
3)
3)
1)
2)
24
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500L_10 _AM
AMZ 0560L_10 _AM
See ordering information - section for details on motor type and product
code, variant code 183 used only with air cooled, IC416 motors
Separate cooling fan power not considered in efficiency value
3)
4)
Output values and more base speeds for IEC 500 and 560 sizes on request
Tmax/TN value represents maximum short time overloadability with inverter
supply. This does not represent the pull-out torque value according to IEC.
Product code1)
Current
IN
A
Efficiency
Full load2)
%
Torque
TN
Nm
Power
factor
cos
Torque
TN4)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Tmax
Weight
approx.
kg
nn = 159 r/min
21
29
45
58
72
79
108
126
159
219
299
385
486
602
721
839
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0500LR10 _AM
AMZ 0560LQ10 _AM
AMZ 0560LS10 _AM
AMZ 0560LU10 _AM
3G_J286220-_D_183705
3G_J316230-_D_183705
3G_J316410-_D_183705
3G_J316820-_D_183705
3G_J316830-_D_183705
3G_J356220-_D_183705
3G_J356420-_D_183705
3G_J356820-_D_183705
3G_J406530-_D_183705
34
44
68
84
106
113
154
178
220
310
415
533
680
831
1000
1149
84.3
87.9
88.8
89.6
90.8
90.5
90.9
91.6
92.5
94.4
94.9
95.3
95.6
95.9
96.1
96.1
1287
1742
2730
3463
4352
4775
6510
7596
9550
13154
17959
23124
29191
36158
43305
50393
0.93
0.94
0.94
0.96
0.94
0.97
0.96
0.97
0.97
0.93
0.94
0.94
0.93
0.94
0.93
0.94
1.0
1.1
1.1
1.1
1.1
1.2
1.2
1.2
1.1
1.2
1.2
1.2
1.2
1.3
1.4
1.3
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
135
224
265
306
191
191
191
191
191
191
191
191
191
191
191
191
191
191
191
191
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
7580
10490
11480
12470
3G_J286220-_D_183706
3G_J316230-_D_183706
3G_J316410-_D_183706
3G_J316820-_D_183706
3G_J316830-_D_183706
3G_J356220-_D_183706
3G_J356420-_D_183706
3G_J356820-_D_183706
3G_J406530-_D_183706
45
68
95
115
158
151
201
228
296
417
576
750
927
1135
1299
1514
87.8
89.4
90.8
92.2
92.1
92.6
93.2
93.9
94.3
95.5
96.0
96.3
96.5
96.7
96.8
96.9
1299
2004
2864
3501
4787
4774
6361
7150
9547
13159
18308
23809
29266
36308
42293
49334
0.92
0.93
0.94
0.94
0.93
0.97
0.96
0.95
0.97
0.93
0.93
0.93
0.92
0.93
0.95
0.95
1.0
1.0
1.0
1.1
1.1
1.2
1.2
1.3
1.1
1.2
1.2
1.2
1.3
1.4
1.3
1.3
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
135
224
265
306
260
260
260
260
260
260
260
260
260
260
260
260
260
260
260
260
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
7580
10490
11480
12470
3G_J286220-_D_183705
3G_J316230-_D_183705
3G_J316410-_D_183705
3G_J316820-_D_183705
3G_J316830-_D_183705
3G_J356220-_D_183705
3G_J356420-_D_183705
3G_J356820-_D_183705
3G_J406530-_D_183705
57
74
113
140
177
188
257
295
366
531
826
1060
1510
1824
89.7
91.9
92.7
93.1
93.8
93.5
93.9
94.2
95.0
96.3
96.8
96.9
97.3
97.3
1303
1729
2715
3442
4280
4707
6422
7449
9404
13231
20871
26566
38860
46673
0.91
0.92
0.93
0.95
0.93
0.96
0.96
0.96
0.97
0.93
0.93
0.92
0.94
0.94
1.0
1.1
1.1
1.1
1.2
1.2
1.2
1.2
1.1
1.3
1.3
1.3
1.3
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
101
124
245
286
330
330
330
330
330
330
330
330
330
330
330
330
330
330
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6410
7190
10990
11980
29
45
65
79
109
108
144
162
217
299
416
541
665
825
961
1121
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0500LR10 _AM
AMZ 0560LQ10 _AM
AMZ 0560LS10 _AM
AMZ 0560LU10 _AM
500 V
nn = 217 r/min
nn = 275 r/min
38
50
78
99
123
136
185
215
271
381
601
765
1119
1344
1)
2)
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LL10 _AM
AMZ 0500LQ10 _AM
AMZ 0560LR10 _AM
AMZ 0560LT10 _AM
See ordering information - section for details on motor type and product
code, variant code 183 used only with air cooled, IC416 motors
Separate cooling fan power not considered in efficiency value
3)
4)
Output values and more base speeds for IEC 500 and 560 sizes on request
Tmax/TN value represents maximum short time overloadability with inverter
supply. This does not represent the pull-out torque value according to IEC.
25
Product code1)
Current
IN
A
Efficiency
Full load2)
%
Torque
TN
Nm
Power
factor
cos
Torque
TN4)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Tmax
Weight
approx.
kg
nn = 310 r/min
40
58
90
108
144
144
202
241
306
416
602
774
941
1293
1647
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0560LL10 _AM
AMZ 0560LR10 _AM
AMZ 0560LU10 _AM
3G_J286220-_D_183707
3G_J316230-_D_183707
3G_J316410-_D_183707
3G_J316820-_D_183707
3G_J316830-_D_183707
3G_J356220-_D_183707
3G_J356420-_D_183707
3G_J356820-_D_183707
3G_J406530-_D_183707
59
83
130
153
204
195
282
329
435
570
832
1068
1293
1809
2263
91.1
92.3
93.3
94.1
94.1
94.1
94.9
95.1
95.7
96.5
96.9
97.1
97.3
97.5
97.6
1222
1777
2775
3330
4440
4440
6206
7429
9427
12815
18545
23844
28989
39833
50738
0.92
0.95
0.93
0.94
0.94
0.98
0.94
0.96
0.92
0.94
0.93
0.93
0.93
0.93
0.93
1.0
1.1
1.1
1.2
1.1
1.2
1.3
1.3
1.3
1.2
1.3
1.3
1.4
1.4
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
183
245
306
372
372
372
372
372
372
372
372
372
372
372
372
372
372
372
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
9500
10990
12470
3G_J286220-_D_183706
3G_J316230-_D_183706
3G_J316410-_D_183706
3G_J316820-_D_183706
3G_J316830-_D_183706
3G_J356220-_D_183706
3G_J356420-_D_183706
3G_J356820-_D_183706
3G_J406530-_D_183706
77
114
158
190
263
250
333
373
491
737
1221
1508
2256
91.9
92.9
93.7
94.6
94.5
94.7
95.1
95.4
95.9
97.0
97.4
97.5
97.7
1303
1987
2825
3409
4676
4664
6197
6826
9309
13243
22920
28421
42606
0.91
0.92
0.94
0.93
0.92
0.96
0.96
0.94
0.97
0.92
0.94
0.94
0.94
1.0
1.0
1.0
1.2
1.1
1.2
1.2
1.4
1.2
1.3
1.3
1.4
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
113
183
265
450
450
450
450
450
450
450
450
450
450
450
450
450
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6800
9500
11480
3G_J286220-_D_183708
3G_J316230-_D_183708
3G_J316410-_D_183708
3G_J316820-_D_183708
3G_J316830-_D_183708
3G_J356220-_D_183708
3G_J356420-_D_183708
3G_J356820-_D_183708
3G_J406530-_D_183708
86
113
160
205
273
275
369
404
541
827
1481
1833
2245
2471
92.9
94.2
94.7
95.3
95.1
95.4
95.7
95.8
96.4
97.2
97.6
97.6
97.8
98.0
1274
1750
2546
3179
4322
4415
5964
6765
8906
13211
23754
29025
35972
41486
0.90
0.93
0.95
0.92
0.94
0.95
0.96
0.99
0.97
0.92
0.92
0.92
0.93
0.96
1.0
1.1
1.1
1.3
1.1
1.3
1.3
1.3
1.2
1.3
1.3
1.3
1.4
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
113
135
224
306
520
520
520
520
520
520
520
520
520
520
520
520
520
520
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6800
7580
10490
12470
nn = 375 r/min
500 V
51
78
111
134
184
183
243
268
366
520
900
1116
1673
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LN10 _AM
AMZ 0560LL10 _AM
AMZ 0560LS10 _AM
nn = 433 r/min
58
79
116
144
196
200
270
307
404
599
1077
1316
1631
1881
1)
2)
26
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LN10 _AM
AMZ 0500LR10 _AM
AMZ 0560LQ10 _AM
AMZ 0560LU10 _AM
See ordering information - section for details on motor type and product
code, variant code 183 used only with air cooled, IC 416 motors
Separate cooling fan power not considered in efficiency value
3)
4)
Output values and more base speeds for IEC 500 and 560 sizes on request
Tmax/TN value represents maximum short time overloadability with inverter
supply. This does not represent the pull-out torque value according to IEC.
Product code1)
Current
IN
A
Efficiency
Full load2)
%
Torque
TN
Nm
Power
factor
cos
Torque
TN4)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Weight
approx.
kg
660
Tmax
nn = 538 r/min
67
97
151
179
239
239
330
392
491
741
1035
1330
1612
1881
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0560LL10 _AM
AMZ 0560LR10 _AM
3G_J286220-_D_183707
3G_J316230-_D_183707
3G_J316410-_D_183707
3G_J316820-_D_183707
3G_J316830-_D_183707
3G_J356220-_D_183707
3G_J356420-_D_183707
3G_J356820-_D_183707
3G_J406530-_D_183707
98
136
214
250
333
318
458
528
693
1046
1459
1828
2233
2496
93.7
94.6
95.2
95.5
95.6
95.6
96.0
96.1
96.7
97.4
97.6
97.8
97.9
98.1
1196
1727
2684
3185
4245
4247
5858
6961
8727
13153
18372
23609
28614
33389
0.92
0.94
0.93
0.94
0.94
0.98
0.94
0.96
0.92
0.92
0.92
0.92
0.93
0.95
1.1
1.1
1.1
1.2
1.2
1.3
1.4
1.4
1.4
1.3
1.3
1.3
1.4
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
183
245
646
646
646
646
646
646
646
646
646
646
646
646
646
646
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
9500
10990
3G_J286220-_D_183708
3G_J316230-_D_183708
3G_J316410-_D_183708
3G_J316820-_D_183708
3G_J316830-_D_183708
3G_J356220-_D_183708
3G_J356420-_D_183708
3G_J356820-_D_183708
3G_J406530-_D_183708
141
183
259
326
393
383
585
636
863
94.7
95.5
95.8
96.0
96.1
96.2
96.4
96.4
97.1
1223
1655
2411
2931
3689
3595
5494
6211
8288
0.90
0.93
0.95
0.92
0.96
0.96
0.96
0.99
0.97
1.1
1.2
1.2
1.4
1.3
1.6
1.4
1.4
1.3
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
863
863
863
863
863
863
863
863
863
660
890
1125
1430
1605
1780
2210
2690
3280
3)
3)
1)
2)
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500L_10 _AM
AMZ 0560L_10 _AM
See ordering information - section for details on motor type and product
code, variant code 183 used only with air cooled, IC 416 motors
Separate cooling fan power not considered in efficiency value
3)
4)
500 V
nn = 750 r/min
96
130
189
230
290
282
432
488
651
Output values and more base speeds for IEC 500 and 560 sizes on request
Tmax/TN value represents maximum short time overloadability with inverter
supply. This does not represent the pull-out torque value according to IEC.
27
Product code1)
Current
IN
A
Efficiency
Full load2)
%
Torque
TN
Nm
Power
factor
cos
Torque
TN4)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Tmax
Weight
approx.
kg
nn = 183 r/min
25
33
52
66
83
91
124
145
183
253
344
443
560
694
833
964
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0500LR10 _AM
AMZ 0560LQ10 _AM
AMZ 0560LS10 _AM
AMZ 0560LU10 _AM
3G_J286220-_D_183705
3G_J316230-_D_183705
3G_J316410-_D_183705
3G_J316820-_D_183705
3G_J316830-_D_183705
3G_J356220-_D_183705
3G_J356420-_D_183705
3G_J356820-_D_183705
3G_J406530-_D_183705
34
44
67
83
105
112
153
177
218
310
414
531
680
831
1005
1146
85.9
89.0
90.0
90.7
91.7
91.5
91.9
92.5
93.3
95.0
95.5
95.8
96.0
96.3
96.5
96.5
1302
1744
2735
3473
4351
4771
6505
7592
9548
13203
17952
23118
29224
36217
43471
50307
0.93
0.93
0.94
0.96
0.94
0.97
0.96
0.97
0.97
0.93
0.94
0.94
0.93
0.94
0.93
0.94
1.0
1.1
1.1
1.1
1.1
1.2
1.2
1.2
1.1
1.2
1.2
1.2
1.3
1.3
1.4
1.3
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
135
224
265
306
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
7580
10490
11480
12470
3G_J286220-_D_183706
3G_J316230-_D_183706
3G_J316410-_D_183706
3G_J316820-_D_183706
3G_J316830-_D_183706
3G_J356220-_D_183706
3G_J356420-_D_183706
3G_J356820-_D_183706
3G_J406530-_D_183706
45
68
94
114
157
150
200
227
295
418
575
749
923
1132
1297
1512
89.2
90.5
91.8
93.0
92.9
93.3
93.8
94.4
94.8
96.0
96.4
96.6
96.8
97.0
97.1
97.2
1303
2006
2864
3500
4786
4771
6359
7147
9545
13232
18333
23856
29225
36244
42342
49399
0.92
0.93
0.94
0.93
0.93
0.97
0.96
0.94
0.97
0.93
0.93
0.93
0.92
0.93
0.95
0.95
1.0
1.0
1.0
1.1
1.1
1.2
1.2
1.3
1.1
1.2
1.2
1.3
1.3
1.4
1.3
1.3
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
135
224
265
306
299
299
299
299
299
299
299
299
299
299
299
299
299
299
299
299
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
7580
10490
11480
12470
3G_J286220-_D_183705
3G_J316230-_D_183705
3G_J316410-_D_183705
3G_J316820-_D_183705
3G_J316830-_D_183705
3G_J356220-_D_183705
3G_J356420-_D_183705
3G_J356820-_D_183705
3G_J406530-_D_183705
57
72
111
137
172
184
251
287
357
531
742
929
1292
1508
1819
90.9
92.6
93.3
93.7
94.3
94.1
94.4
94.7
95.4
96.6
96.9
97.1
97.4
97.5
97.5
1303
1702
2674
3388
4187
4615
6293
7281
9215
13267
18586
23512
32579
38865
46632
0.91
0.92
0.93
0.95
0.93
0.96
0.96
0.96
0.97
0.92
0.92
0.93
0.93
0.94
0.94
1.0
1.2
1.1
1.1
1.2
1.2
1.2
1.2
1.1
1.3
1.3
1.3
1.4
1.4
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
203
245
286
379
379
379
379
379
379
379
379
379
379
379
379
379
379
379
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
10000
10990
11980
nn = 249 r/min
575 V
34
52
75
91
125
124
166
186
249
345
478
622
762
945
1104
1288
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0500LR10 _AM
AMZ 0560LQ10 _AM
AMZ 0560LS10 _AM
AMZ 0560LU10 _AM
nn = 316 r/min
43
56
89
112
139
153
208
241
305
439
615
778
1078
1286
1543
1)
2)
28
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0560LN10 _AM
AMZ 0560LR10 _AM
AMZ 0560LT10 _AM
See ordering information - section for details on motor type and product
code, variant code 183 used only with air cooled, IC 416 motors
Separate cooling fan power not considered in efficiency value
3)
4)
Output values and more base speeds for IEC 500 and 560 sizes on request
Tmax/TN value represents maximum short time overloadability with inverter
supply. This does not represent the pull-out torque value according to IEC.
Product code1)
Current
IN
A
Efficiency
Full load2)
%
Torque
TN
Nm
Power
factor
cos
Torque
TN4)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Tmax
Weight
approx.
kg
nn = 357 r/min
46
66
104
124
166
166
232
278
352
478
690
887
1080
1486
1889
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0560LL10 _AM
AMZ 0560LR10 _AM
AMZ 0560LU10 _AM
3G_J286220-_D_183707
3G_J316230-_D_183707
3G_J316410-_D_183707
3G_J316820-_D_183707
3G_J316830-_D_183707
3G_J356220-_D_183707
3G_J356420-_D_183707
3G_J356820-_D_183707
3G_J406530-_D_183707
59
82
129
153
203
194
282
328
434
568
827
1062
1289
1805
2253
92.0
93.1
93.8
94.5
94.6
94.5
95.2
95.4
96.0
96.8
97.1
97.3
97.5
97.6
97.7
1222
1776
2775
3330
4440
4439
6205
7427
9426
12787
18458
23728
28891
39752
50532
0.92
0.94
0.93
0.94
0.94
0.98
0.94
0.96
0.92
0.94
0.93
0.93
0.93
0.93
0.93
1.0
1.1
1.1
1.2
1.1
1.2
1.3
1.3
1.3
1.2
1.3
1.3
1.4
1.4
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
183
245
306
428
428
428
428
428
428
428
428
428
428
428
428
428
428
428
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
9500
10990
12470
3G_J286220-_D_183706
3G_J316230-_D_183706
3G_J316410-_D_183706
3G_J316820-_D_183706
3G_J316830-_D_183706
3G_J356220-_D_183706
3G_J356420-_D_183706
3G_J356820-_D_183706
3G_J406530-_D_183706
75
112
154
184
255
242
321
356
474
737
1216
1503
2247
92.6
93.5
94.3
94.9
95.0
95.1
95.5
95.7
96.2
97.2
97.6
97.7
97.9
1279
1956
2771
3310
4555
4529
5998
6524
9019
13228
22867
28362
42476
0.91
0.92
0.94
0.93
0.92
0.97
0.96
0.94
0.97
0.92
0.94
0.94
0.94
1.0
1.0
1.1
1.2
1.1
1.3
1.3
1.4
1.2
1.3
1.3
1.4
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
113
183
265
517
517
517
517
517
517
517
517
517
517
517
517
517
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6800
9500
11480
3G_J286220-_D_183708
3G_J316230-_D_183708
3G_J316410-_D_183708
3G_J316820-_D_183708
3G_J316830-_D_183708
3G_J356220-_D_183708
3G_J356420-_D_183708
3G_J356820-_D_183708
3G_J406530-_D_183708
86
113
160
205
247
245
369
403
540
824
1473
1823
2236
2472
93.5
94.5
95.1
95.6
95.6
95.8
96.0
96.0
96.7
97.3
97.7
97.8
97.9
98.1
1274
1750
2546
3179
3976
3972
5963
6764
8905
13174
23645
28880
35822
41479
0.90
0.93
0.95
0.92
0.95
0.96
0.95
0.99
0.97
0.92
0.92
0.92
0.93
0.96
1.0
1.1
1.1
1.3
1.2
1.4
1.3
1.3
1.2
1.3
1.3
1.3
1.4
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
113
135
224
306
598
598
598
598
598
598
598
598
598
598
598
598
598
598
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6800
7580
10490
12470
nn = 431 r/min
58
88
125
150
206
205
271
295
407
597
1032
1280
1917
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LN10 _AM
AMZ 0560LL10 _AM
AMZ 0560LS10 _AM
1)
2)
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LN10 _AM
AMZ 0500LR10 _AM
AMZ 0560LQ10 _AM
AMZ 0560LU10 _AM
See ordering information - section for details on motor type and product
code, variant code 183 used only with air cooled, IC 416 motors
Separate cooling fan power not considered in efficiency value
3)
4)
575 V
nn = 498 r/min
66
91
133
166
207
207
311
353
464
687
1233
1506
1868
2163
Output values and more base speeds for IEC 500 and 560 sizes on request
Tmax/TN value represents maximum short time overloadability with inverter
supply. This does not represent the pull-out torque value according to IEC.
29
Product code1)
Current
IN
A
Efficiency
Full load2)
%
Torque
TN
Nm
Power
factor
cos
Torque
TN4)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Tmax
Weight
approx.
kg
nn = 618 r/min
75
108
167
196
263
263
357
423
531
847
1181
1518
1840
2162
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0560LL10 _AM
AMZ 0560LR10 _AM
3G_J286220-_D_183707
3G_J316230-_D_183707
3G_J316410-_D_183707
3G_J316820-_D_183707
3G_J316830-_D_183707
3G_J356220-_D_183707
3G_J356420-_D_183707
3G_J356820-_D_183707
3G_J406530-_D_183707
95
131
205
237
316
302
431
494
651
1040
1449
1813
2218
2497
94.2
95.0
95.4
95.7
95.8
95.8
96.2
96.3
96.8
97.6
97.7
97.8
98.0
98.1
1164
1674
2586
3033
4056
4062
5517
6536
8196
13089
18250
23458
28434
33410
0.92
0.94
0.93
0.94
0.94
0.99
0.94
0.97
0.91
0.92
0.92
0.92
0.93
0.95
1.1
1.2
1.2
1.3
1.2
1.3
1.5
1.5
1.5
1.3
1.3
1.3
1.4
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
183
245
742
742
742
742
742
742
742
742
742
742
742
742
742
742
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
9500
10990
3G_J286220-_D_183708
3G_J316230-_D_183708
3G_J316410-_D_183708
3G_J316820-_D_183708
3G_J316830-_D_183708
3G_J356220-_D_183708
3G_J356420-_D_183708
3G_J356820-_D_183708
3G_J406530-_D_183708
134
172
242
299
362
346
534
579
792
95.0
95.7
95.9
96.0
96.2
96.1
96.4
96.4
97.1
1171
1566
2273
2687
3411
3247
5033
5675
7645
0.90
0.93
0.96
0.92
0.96
0.96
0.96
1.00
0.98
1.1
1.3
1.2
1.5
1.4
1.8
1.5
1.5
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
863
863
863
863
863
863
863
863
863
660
890
1125
1430
1605
1780
2210
2690
3280
nn = 863 r/min
106
142
205
243
308
293
455
513
691
3)
3)
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500L_10 _AM
AMZ 0560L_10 _AM
575 V
1)
2)
30
See ordering information - section for details on motor type and product
code, variant code 183 used only with air cooled, IC 416 motors
Separate cooling fan power not considered in efficiency value
3)
4)
Output values and more base speeds for IEC 500 and 560 sizes on request
Tmax/TN value represents maximum short time overloadability with inverter
supply. This does not represent the pull-out torque value according to IEC.
Product code1)
Current
IN
A
Efficiency
Full load2)
%
Torque
TN
Nm
Power
factor
cos
Torque
Tmax
TN4)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Weight
approx.
kg
nn = 220 r/min
30
40
63
80
100
109
149
174
219
305
413
532
673
834
1003
1157
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0500LR10 _AM
AMZ 0560LQ10 _AM
AMZ 0560LS10 _AM
AMZ 0560LU10 _AM
3G_J286220-_D_183705
3G_J316230-_D_183705
3G_J316410-_D_183705
3G_J316820-_D_183705
3G_J316830-_D_183705
3G_J356220-_D_183705
3G_J356420-_D_183705
3G_J356820-_D_183705
3G_J406530-_D_183705
33
43
67
82
105
111
152
175
217
310
412
529
678
830
1007
1142
87.9
90.5
91.3
91.9
92.7
92.5
92.9
93.4
94.1
95.7
96.1
96.3
96.5
96.8
96.9
97
1303
1743
2734
3472
4350
4769
6501
7591
9546
13240
17928
23094
29214
36203
43539
50224
0.92
0.93
0.94
0.95
0.93
0.96
0.96
0.96
0.97
0.93
0.94
0.94
0.93
0.94
0.93
0.94
1.0
1.1
1.1
1.1
1.1
1.2
1.2
1.2
1.1
1.3
1.2
1.2
1.3
1.4
1.4
1.3
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
135
224
265
306
220
220
220
220
220
220
220
220
220
264
264
264
264
264
264
264
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
7580
10490
11480
12470
3G_J286220-_D_183706
3G_J316230-_D_183706
3G_J316410-_D_183706
3G_J316820-_D_183706
3G_J316830-_D_183706
3G_J356220-_D_183706
3G_J356420-_D_183706
3G_J356820-_D_183706
3G_J406530-_D_183706
45
67
93
114
157
149
199
227
293
416
573
746
923
1131
1289
1503
90.7
91.8
92.8
93.7
93.7
94.0
94.4
94.9
95.3
96.5
96.8
97.0
97.2
97.4
97.4
97.5
1303
2006
2864
3500
4786
4769
6355
7153
9543
13179
18272
23748
29223
36226
42084
49087
0.91
0.92
0.94
0.93
0.92
0.96
0.96
0.94
0.97
0.93
0.93
0.93
0.92
0.93
0.95
0.95
1.0
1.0
1.0
1.1
1.1
1.2
1.2
1.3
1.1
1.2
1.3
1.3
1.3
1.4
1.4
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
135
224
265
306
300
300
300
300
300
300
300
300
300
360
360
360
360
360
360
360
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
7580
10490
11480
12470
3G_J286220-_D_183705
3G_J316230-_D_183705
3G_J316410-_D_183705
3G_J316820-_D_183705
3G_J316830-_D_183705
3G_J356220-_D_183705
3G_J356420-_D_183705
3G_J356820-_D_183705
3G_J406530-_D_183705
55
70
107
132
165
176
240
274
342
530
742
924
1135
1499
1809
91.9
93.3
93.9
94.3
94.8
94.7
94.9
95.2
95.8
97.0
97.2
97.4
97.6
97.7
97.8
1283
1653
2599
3289
4023
4451
6065
6985
8887
13244
18572
23398
28876
38652
46368
0.91
0.91
0.93
0.95
0.93
0.96
0.96
0.96
0.98
0.92
0.92
0.93
0.93
0.94
0.94
1.0
1.2
1.1
1.1
1.2
1.3
1.3
1.3
1.2
1.3
1.3
1.3
1.4
1.4
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
183
245
286
380
380
380
380
380
380
380
380
380
456
456
456
456
456
456
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
9500
10990
11980
nn = 300 r/min
41
63
90
110
150
149
199
224
299
414
574
746
918
1138
1322
1542
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0500LR10 _AM
AMZ 0560LQ10 _AM
AMZ 0560LS10 _AM
AMZ 0560LU10 _AM
51
66
103
131
160
177
241
278
353
527
739
931
1149
1538
1845
1)
2)
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0560LL10 _AM
AMZ 0560LR10 _AM
AMZ 0560LT10 _AM
See ordering information - section for details on motor type and product
code, variant code 183 used only with air cooled, IC 416 motors
Separate cooling fan power not considered in efficiency value
3)
4)
690 V
nn = 380 r/min
Output values and more base speeds for IEC 500 and 560 sizes on request
Tmax/TN value represents maximum short time overloadability with inverter
supply. This does not represent the pull-out torque value according to IEC.
31
Product code1)
Current
IN
A
Efficiency
Full load2)
%
Torque
TN
Nm
Power
factor
cos
Torque
Tmax
TN4)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Weight
approx.
kg
nn = 430 r/min
55
80
124
149
199
199
278
333
421
572
826
1061
1298
1781
2267
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LJ10 _AM
AMZ 0500LN10 _AM
AMZ 0560LL10 _AM
AMZ 0560LR10 _AM
AMZ 0560LU10 _AM
3G_J286220-_D_183707
3G_J316230-_D_183707
3G_J316410-_D_183707
3G_J316820-_D_183707
3G_J316830-_D_183707
3G_J356220-_D_183707
3G_J356420-_D_183707
3G_J356820-_D_183707
3G_J406530-_D_183707
58
82
129
152
203
193
281
328
432
564
823
1055
1286
1796
2244
92.9
93.9
94.5
95.0
95.1
95.0
95.6
95.8
96.3
97.2
97.4
97.5
97.7
97.8
97.9
1222
1776
2774
3329
4440
4440
6205
7433
9394
12704
18345
23564
28828
39555
50348
0.92
0.94
0.93
0.94
0.94
0.98
0.94
0.96
0.92
0.94
0.93
0.93
0.93
0.93
0.93
1.0
1.1
1.1
1.2
1.1
1.2
1.3
1.3
1.3
1.3
1.3
1.3
1.4
1.4
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
183
245
306
430
430
430
430
430
430
430
430
430
516
516
516
516
516
516
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
9500
10990
12470
3G_J286220-_D_183706
3G_J316230-_D_183706
3G_J316410-_D_183706
3G_J316820-_D_183706
3G_J316830-_D_183706
3G_J356220-_D_183706
3G_J356420-_D_183706
3G_J356820-_D_183706
3G_J406530-_D_183706
72
107
147
174
241
228
301
328
445
733
1458
1491
2228
93.5
94.2
94.8
95.3
95.4
95.5
95.8
95.9
96.5
97.4
97.8
97.9
98.0
1245
1899
2674
3139
4344
4296
5656
6011
8532
13164
26235
28152
42127
0.91
0.92
0.94
0.93
0.93
0.97
0.96
0.94
0.97
0.92
0.92
0.94
0.94
1.0
1.1
1.1
1.3
1.2
1.3
1.3
1.5
1.3
1.3
1.3
1.4
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
124
183
265
518
518
518
518
518
518
518
518
518
622
622
622
622
660
890
1125
1430
1605
1780
2210
2690
3280
5240
7190
9500
11480
3G_J286220-_D_183708
3G_J316230-_D_183708
3G_J316410-_D_183708
3G_J316820-_D_183708
3G_J316830-_D_183708
3G_J356220-_D_183708
3G_J356420-_D_183708
3G_J356820-_D_183708
3G_J406530-_D_183708
86
113
159
205
247
245
368
402
539
816
1457
1808
2219
2467
94.1
95.0
95.4
95.8
95.9
96.0
96.2
96.2
96.9
97.5
97.8
97.9
98.1
98.2
1274
1750
2546
3179
3976
3973
5963
6763
8904
13036
23366
28650
35574
41288
0.90
0.93
0.95
0.92
0.95
0.96
0.95
0.99
0.97
0.93
0.93
0.92
0.93
0.96
1.0
1.1
1.1
1.3
1.2
1.4
1.3
1.3
1.2
1.3
1.3
1.3
1.4
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
113
135
224
306
600
600
600
600
600
600
600
600
600
720
720
720
720
720
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6800
7580
10490
12470
nn = 518 r/min
68
103
145
170
235
233
307
326
462
714
1423
1527
2285
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LQ10 _AM
AMZ 0560LL10 _AM
AMZ 0560LS10 _AM
nn = 600 r/min
690 V
80
110
159
199
249
249
373
423
557
819
1468
1800
2235
2594
1)
2)
32
M3_J 280SMB
M3_J 315SMC
M3_J 315MLA
M3_J 315LKB
M3_J 315LKC
M3_J 355SMB
M3_J 355MLB
M3_J 355LKB
M3_J 400LC
AMZ 0500LE10 _AM
AMZ 0500LN10 _AM
AMZ 0500LR10 _AM
AMZ 0560LQ10 _AM
AMZ 0560LU10 _AM
See ordering information - section for details on motor type and product
code, variant code 183 used only with air cooled, IC 416 motors
Separate cooling fan power not considered in efficiency value
3)
4)
Output values and more base speeds for IEC 500 and 560 sizes on request
Tmax/TN value represents maximum short time overloadability with inverter
supply. This does not represent the pull-out torque value according to IEC.
Product code1)
Current
IN
A
3G_J286220-_D_183707
3G_J316230-_D_183707
3G_J316410-_D_183707
3G_J316820-_D_183707
3G_J316830-_D_183707
3G_J356220-_D_183707
3G_J356420-_D_183707
3G_J356820-_D_183707
3G_J406530-_D_183707
90
123
191
216
289
277
387
439
584
1030
1432
1790
2192
2495
Torque
94.6
95.3
95.7
95.9
96.0
96.0
96.2
96.3
96.8
97.7
97.8
97.9
98.1
98.1
1106
1580
2417
2772
3730
3748
4940
5818
7321
12961
18057
23180
28122
33361
TN
Nm
Power
factor
cos
0.92
0.95
0.93
0.94
0.95
0.99
0.93
0.97
0.91
0.92
0.92
0.92
0.93
0.95
Torque
Tmax
TN4)
1.1
1.2
1.3
1.4
1.3
1.4
1.6
1.7
1.7
1.3
1.3
1.3
1.4
1.6
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
68
90
113
183
245
742
742
742
742
742
742
742
742
742
890
890
890
890
890
Weight
approx.
kg
660
890
1125
1430
1605
1780
2210
2690
3280
5240
6020
6800
9500
10990
690 V
nn = 742 r/min
86
M3_J 280SMB
123
M3_J 315SMC
188
M3_J 315MLA
215
M3_J 315LKB
290
M3_J 315LKC
291
M3_J 355SMB
384
M3_J 355MLB
452
M3_J 355LKB
569
M3_J 400LC
1007
AMZ 0500LE10 _AM
1403
AMZ 0500LJ10 _AM
1801
AMZ 0500LN10 _AM
2185
AMZ 0560LL10 _AM
2592
AMZ 0560LR10 _AM
Efficiency
Full load2)
%
1)
2)
See ordering information - section for details on motor type and product
code, variant code 183 used only with air cooled, IC416 motors
Separate cooling fan power not considered in efficiency value
3)
4)
Output values and more base speeds for IEC 500 and 560 sizes on request
Tmax/TN value represents maximum short time overloadability with inverter
supply. This does not represent the pull-out torque value according to IEC.
33
Product code1)
Current
IN
A
Efficiency
Full load
%
Torque
TN
Nm
Power
factor
cos
Torque
TN3)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Tmax
Weight
approx.
kg
nn = 127 r/min
400 V
11
16
24
30
41
40
54
67
81
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
2)
2)
3GBJ286220-_DG705
3GBJ316230-_DG705
3GBJ316410-_DG705
3GBJ316820-_DG705
3GBJ316830-_DG705
3GBJ356220-_DG705
3GBJ356420-_DG705
3GBJ356820-_DG705
3GBJ406530-_DG705
21
31
45
53
75
72
96
116
137
86.5
88.1
90.0
90.9
91.2
91.4
91.8
92.5
93.5
819
1228
1833
2242
3052
3038
4047
5067
6103
0.93
0.92
0.94
0.97
0.93
0.96
0.95
0.98
0.99
1.4
1.5
1.5
1.5
1.5
1.8
1.8
1.7
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
152
152
152
152
152
152
152
152
152
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG706
3GBJ316230-_DG706
3GBJ316410-_DG706
3GBJ316820-_DG706
3GBJ316830-_DG706
3GBJ356220-_DG706
3GBJ356420-_DG706
3GBJ356820-_DG706
3GBJ406530-_DG706
31
45
61
79
99
93
140
173
200
89.1
90.7
91.9
92.7
92.8
93.1
93.5
93.9
94.6
899
1343
1880
2385
2980
2967
4447
5481
6557
0.93
0.93
0.95
0.93
0.91
0.97
0.96
0.95
0.98
1.3
1.4
1.5
1.6
1.6
1.8
1.6
1.7
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
208
208
208
208
208
208
208
208
208
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG705
3GBJ316230-_DG705
3GBJ316410-_DG705
3GBJ316820-_DG705
3GBJ316830-_DG705
3GBJ356220-_DG705
3GBJ356420-_DG705
3GBJ356820-_DG705
3GBJ406530-_DG705
39
57
83
97
137
132
177
212
251
90.1
91.2
92.6
93.2
93.5
93.4
93.9
94.3
95.1
869
1307
1953
2387
3254
3253
4335
5422
6507
0.90
0.90
0.92
0.95
0.91
0.95
0.94
0.98
0.98
1.3
1.4
1.4
1.4
1.4
1.6
1.7
1.6
1.5
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
264
264
264
264
264
264
264
264
264
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG707
3GBJ316230-_DG707
3GBJ316410-_DG707
3GBJ316820-_DG707
3GBJ316830-_DG707
3GBJ356220-_DG707
3GBJ356420-_DG707
3GBJ356820-_DG707
3GBJ406530-_DG707
45
60
97
119
152
135
211
256
330
91.4
92.7
93.3
94.0
94.2
94.3
94.7
94.9
95.6
940
1312
2079
2599
3327
3111
4535
5787
6941
0.93
0.95
0.93
0.94
0.95
0.99
0.92
0.97
0.89
1.3
1.4
1.4
1.4
1.4
1.6
1.7
1.6
1.7
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
298
298
298
298
298
298
298
298
298
650
880
1115
1415
1590
1765
2190
2670
3260
nn = 173 r/min
16
24
34
43
54
54
81
99
119
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
nn = 220 r/min
20
30
45
55
75
75
100
125
150
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
nn = 248 r/min
25
34
54
68
87
81
118
150
181
2)
2)
1)
2)
34
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
See ordering information - section for details on motor type and product
code.
Performance values for IEC frame sizes 500 and 560 on request
3)
Product code1)
Current
IN
A
Efficiency
Full load
%
Torque
TN
Nm
Power
factor
cos
Torque
TN3)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Weight
approx.
kg
Tmax
30
45
63
80
100
100
150
185
220
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
3GBJ286220-_DG706
3GBJ316230-_DG706
3GBJ316410-_DG706
3GBJ316820-_DG706
3GBJ316830-_DG706
3GBJ356220-_DG706
3GBJ356420-_DG706
3GBJ356820-_DG706
3GBJ406530-_DG706
57
83
112
145
183
172
258
321
368
91.7
93.0
93.9
94.3
94.5
94.6
94.9
95.2
95.9
955
1432
2004
2546
3183
3180
4767
5886
6996
0.90
0.91
0.94
0.91
0.90
0.96
0.95
0.95
0.97
1.3
1.3
1.4
1.5
1.5
1.7
1.5
1.6
1.5
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
360
360
360
360
360
360
360
360
360
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG708
3GBJ316230-_DG708
3GBJ316410-_DG708
3GBJ316820-_DG708
3GBJ316830-_DG708
3GBJ356220-_DG708
3GBJ356420-_DG708
3GBJ356820-_DG708
3GBJ406530-_DG708
68
96
122
157
184
185
307
313
422
92.9
93.9
94.6
94.9
95.2
95.3
95.5
95.6
96.4
1003
1490
1969
2379
2980
2960
4960
5274
6996
0.90
0.94
0.96
0.91
0.96
0.95
0.96
1.00
0.97
1.3
1.3
1.4
1.6
1.5
1.9
1.5
1.6
1.5
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
415
415
415
415
415
415
415
415
415
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG707
3GBJ316230-_DG707
3GBJ316410-_DG707
3GBJ316820-_DG707
3GBJ316830-_DG707
3GBJ356220-_DG707
3GBJ356420-_DG707
3GBJ356820-_DG707
3GBJ406530-_DG707
82
111
178
220
280
249
392
475
607
93.4
94.3
94.9
95.2
95.4
95.4
95.6
95.9
96.4
1000
1399
2219
2774
3552
3331
4879
6215
7387
0.91
0.94
0.92
0.93
0.93
0.99
0.92
0.96
0.89
1.2
1.3
1.3
1.4
1.3
1.5
1.6
1.5
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
516
516
516
516
516
516
516
516
516
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG708
3GBJ316230-_DG708
3GBJ316410-_DG708
3GBJ316820-_DG708
3GBJ316830-_DG708
3GBJ356220-_DG708
3GBJ356420-_DG708
3GBJ356820-_DG708
3GBJ406530-_DG708
125
177
226
290
341
344
571
578
782
94.4
95.1
95.6
95.7
95.9
95.9
96.2
96.3
96.9
1068
1591
2100
2545
3182
3181
5327
5643
7472
0.89
0.93
0.95
0.90
0.95
0.95
0.95
0.99
0.97
1.2
1.2
1.3
1.5
1.4
1.7
1.4
1.5
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
720
720
720
720
720
720
720
720
720
650
880
1115
1415
1590
1765
2190
2670
3260
400 V
nn = 300 r/min
nn = 346 r/min
36
54
71
86
108
107
180
191
254
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
nn = 430 r/min
45
63
100
125
160
150
220
280
333
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
nn = 600 r/min
67
100
132
160
200
200
335
355
470
2)
2)
1)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
See ordering information - section for details on motor type and product
code
Performance values for IEC frame sizes 500 and 560 on request
3)
35
Product code1)
Current
IN
A
Efficiency
Full load
%
Torque
TN
Nm
Power
factor
cos
Torque
Tmax
TN3)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Weight
approx.
kg
nn = 146 r/min
13
19
29
35
47
47
63
79
95
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
2)
2)
460 V
3GBJ286220-_DG705
3GBJ316230-_DG705
3GBJ316410-_DG705
3GBJ316820-_DG705
3GBJ316830-_DG705
3GBJ356220-_DG705
3GBJ356420-_DG705
3GBJ356820-_DG705
3GBJ406530-_DG705
22
32
46
54
76
73
97
117
139
87.6
89.3
90.8
91.6
91.9
92.0
92.5
93.0
94.0
830
1246
1861
2275
3098
3086
4112
5148
6197
0.92
0.91
0.93
0.96
0.93
0.96
0.95
0.98
0.99
1.4
1.5
1.5
1.5
1.5
1.7
1.7
1.7
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
175
175
175
175
175
175
175
175
175
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG706
3GBJ316230-_DG706
3GBJ316410-_DG706
3GBJ316820-_DG706
3GBJ316830-_DG706
3GBJ356220-_DG706
3GBJ356420-_DG706
3GBJ356820-_DG706
3GBJ406530-_DG706
31
46
62
80
101
95
142
176
203
89.6
91.0
92.3
93.2
93.3
93.6
93.9
94.2
95.0
912
1364
1908
2422
3026
3016
4521
5573
6660
0.92
0.93
0.95
0.92
0.91
0.96
0.96
0.95
0.98
1.3
1.4
1.4
1.5
1.6
1.8
1.6
1.7
1.5
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
239
239
239
239
239
239
239
239
239
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG705
3GBJ316230-_DG705
3GBJ316410-_DG705
3GBJ316820-_DG705
3GBJ316830-_DG705
3GBJ356220-_DG705
3GBJ356420-_DG705
3GBJ356820-_DG705
3GBJ406530-_DG705
38
57
81
94
134
128
172
206
245
90.8
92.2
93.2
93.6
93.9
94.0
94.2
94.6
95.4
857
1286
1920
2338
3182
3171
4225
5272
6352
0.89
0.89
0.91
0.95
0.91
0.95
0.94
0.97
0.98
1.3
1.5
1.4
1.5
1.5
1.7
1.7
1.7
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
304
304
304
304
304
304
304
304
304
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG707
3GBJ316230-_DG707
3GBJ316410-_DG707
3GBJ316820-_DG707
3GBJ316830-_DG707
3GBJ356220-_DG707
3GBJ356420-_DG707
3GBJ356820-_DG707
3GBJ406530-_DG707
46
61
98
121
154
137
214
260
335
91.6
93.0
93.8
94.3
94.6
94.6
95.0
95.2
95.8
954
1332
2111
2640
3379
3162
4615
5885
7057
0.93
0.95
0.93
0.94
0.94
0.99
0.92
0.96
0.89
1.3
1.4
1.4
1.4
1.4
1.6
1.7
1.6
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
343
343
343
343
343
343
343
343
343
650
880
1115
1415
1590
1765
2190
2670
3260
nn = 199 r/min
19
28
40
51
63
63
94
116
139
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
nn = 253 r/min
23
34
51
62
84
84
112
140
168
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
nn = 286 r/min
29
40
63
79
101
95
138
176
211
2)
2)
1)
2)
36
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
See ordering information - section for details on motor type and product
code
Performance values for IEC frame sizes 500 and 560 on request
3)
Product code1)
Current
IN
A
Efficiency
Full load
%
Torque
TN
Nm
Power
factor
cos
Torque
Tmax
TN3)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Weight
approx.
kg
34
51
71
89
111
111
168
204
246
3)
3)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
3GBJ286220-_DG706
3GBJ316230-_DG706
3GBJ316410-_DG706
3GBJ316820-_DG706
3GBJ316830-_DG706
3GBJ356220-_DG706
3GBJ356420-_DG706
3GBJ356820-_DG706
3GBJ406530-_DG706
56
81
109
140
177
166
251
308
357
92.4
93.6
94.3
94.6
94.8
94.9
95.2
95.4
96.1
940
1405
1956
2462
3064
3067
4636
5642
6805
0.90
0.91
0.93
0.91
0.90
0.95
0.95
0.94
0.97
1.3
1.4
1.4
1.5
1.5
1.7
1.6
1.7
1.5
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
414
414
414
414
414
414
414
414
414
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG708
3GBJ316230-_DG708
3GBJ316410-_DG708
3GBJ316820-_DG708
3GBJ316830-_DG708
3GBJ356220-_DG708
3GBJ356420-_DG708
3GBJ356820-_DG708
3GBJ406530-_DG708
69
97
124
159
187
188
312
318
429
93.4
94.3
94.9
95.3
95.4
95.4
95.7
95.8
96.5
1018
1514
2000
2418
3028
3011
5046
5361
7109
0.90
0.94
0.96
0.90
0.96
0.95
0.96
1.00
0.97
1.3
1.3
1.4
1.6
1.5
1.8
1.5
1.6
1.5
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
478
478
478
478
478
478
478
478
478
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG707
3GBJ316230-_DG707
3GBJ316410-_DG707
3GBJ316820-_DG707
3GBJ316830-_DG707
3GBJ356220-_DG707
3GBJ356420-_DG707
3GBJ356820-_DG707
3GBJ406530-_DG707
80
107
173
212
268
237
373
450
572
93.7
94.6
95.1
95.4
95.6
95.6
95.8
96.0
96.5
978
1360
2152
2677
3411
3180
4628
5896
6930
0.91
0.94
0.92
0.93
0.93
0.99
0.91
0.96
0.88
1.2
1.4
1.3
1.4
1.4
1.6
1.7
1.6
1.7
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
594
594
594
594
594
594
594
594
594
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG708
3GBJ316230-_DG708
3GBJ316410-_DG708
3GBJ316820-_DG708
3GBJ316830-_DG708
3GBJ356220-_DG708
3GBJ356420-_DG708
3GBJ356820-_DG708
3GBJ406530-_DG708
120
170
215
271
319
317
540
540
740
94.5
95.3
95.8
95.8
95.9
95.9
96.3
96.3
97.0
1030
1533
2009
2369
2980
2917
5048
5286
7094
0.89
0.93
0.96
0.90
0.96
0.94
0.95
1.00
0.97
1.2
1.3
1.4
1.6
1.5
1.9
1.5
1.6
1.5
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
828
828
828
828
828
828
828
828
828
650
880
1115
1415
1590
1765
2190
2670
3260
460 V
nn = 345 r/min
nn = 398 r/min
43
63
83
101
126
126
211
224
297
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
nn = 495 r/min
51
70
111
139
177
165
240
305
359
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
nn = 690 r/min
74
111
145
171
215
211
365
382
513
2)
2)
1)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
See ordering information - section for details on motor type and product
code
Performance values for IEC frame sizes 500 and 560 on request
3)
37
Product code1)
Current
IN
A
Efficiency
Full load
%
Torque
TN
Nm
Power
factor
cos
Torque
TN3)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Tmax
Weight
approx.
kg
nn = 159 r/min
14
21
31
38
52
52
69
87
104
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
3GBJ286220-_DG705
3GBJ316230-_DG705
3GBJ316410-_DG705
3GBJ316820-_DG705
3GBJ316830-_DG705
3GBJ356220-_DG705
3GBJ356420-_DG705
3GBJ356820-_DG705
3GBJ406530-_DG705
22
32
46
54
76
73
98
118
140
88.0
89.7
91.0
92.0
92.2
92.5
92.8
93.3
94.2
838
1258
1879
2298
3130
3120
4158
5204
6261
0.91
0.91
0.93
0.96
0.92
0.96
0.95
0.98
0.98
1.4
1.5
1.5
1.5
1.5
1.7
1.7
1.7
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
191
191
191
191
191
191
191
191
191
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG706
3GBJ316230-_DG706
3GBJ316410-_DG706
3GBJ316820-_DG706
3GBJ316830-_DG706
3GBJ356220-_DG706
3GBJ356420-_DG706
3GBJ356820-_DG706
3GBJ406530-_DG706
32
46
62
80
102
96
143
178
205
90.5
91.5
92.8
93.4
93.6
93.8
94.1
94.5
95.3
920
1377
1928
2447
3058
3050
4572
5636
6730
0.91
0.92
0.94
0.92
0.91
0.96
0.96
0.95
0.98
1.3
1.4
1.4
1.5
1.5
1.8
1.6
1.7
1.5
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
260
260
260
260
260
260
260
260
260
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG705
3GBJ316230-_DG705
3GBJ316410-_DG705
3GBJ316820-_DG705
3GBJ316830-_DG705
3GBJ356220-_DG705
3GBJ356420-_DG705
3GBJ356820-_DG705
3GBJ406530-_DG705
38
56
80
92
131
126
168
200
239
91.4
92.4
93.5
94.0
94.1
94.2
94.4
94.9
95.6
844
1265
1886
2291
3115
3096
4120
5145
6210
0.88
0.89
0.91
0.95
0.91
0.94
0.93
0.97
0.98
1.4
1.5
1.5
1.5
1.5
1.7
1.7
1.7
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
330
330
330
330
330
330
330
330
330
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG707
3GBJ316230-_DG707
3GBJ316410-_DG707
3GBJ316820-_DG707
3GBJ316830-_DG707
3GBJ356220-_DG707
3GBJ356420-_DG707
3GBJ356820-_DG707
3GBJ406530-_DG707
46
62
99
122
156
138
217
263
339
92.1
93.4
94.0
94.5
94.8
94.8
95.2
95.4
95.9
964
1346
2134
2668
3415
3196
4669
5952
7134
0.92
0.95
0.93
0.94
0.94
0.99
0.92
0.96
0.89
1.3
1.4
1.4
1.4
1.4
1.6
1.7
1.6
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
372
372
372
372
372
372
372
372
372
650
880
1115
1415
1590
1765
2190
2670
3260
nn = 217 r/min
21
31
44
56
69
69
104
128
153
500 V
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
nn = 275 r/min
24
36
54
66
90
89
119
148
179
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
nn = 310 r/min
31
44
69
87
111
104
152
193
232
2)
2)
1)
2)
38
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
See ordering information - section for details on motor type and product
code
Performance values for IEC frame sizes 500 and 560 on request
3)
Product code1)
Current
IN
A
Efficiency
Full load
%
Torque
TN
Nm
Power
factor
cos
Torque
TN3)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Tmax
Weight
approx.
kg
nn = 375 r/min
36
54
75
94
117
116
177
214
260
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
3GBJ286220-_DG706
3GBJ316230-_DG706
3GBJ316410-_DG706
3GBJ316820-_DG706
3GBJ316830-_DG706
3GBJ356220-_DG706
3GBJ356420-_DG706
3GBJ356820-_DG706
3GBJ406530-_DG706
55
80
106
136
172
161
243
298
346
92.8
93.8
94.5
94.8
94.9
94.9
95.4
95.5
96.2
924
1379
1913
2392
2969
2965
4504
5454
6614
0.90
0.91
0.93
0.91
0.89
0.95
0.95
0.94
0.97
1.3
1.4
1.4
1.6
1.6
1.8
1.6
1.7
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
450
450
450
450
450
450
450
450
450
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG708
3GBJ316230-_DG708
3GBJ316410-_DG708
3GBJ316820-_DG708
3GBJ316830-_DG708
3GBJ356220-_DG708
3GBJ356420-_DG708
3GBJ356820-_DG708
3GBJ406530-_DG708
69
98
125
161
189
190
316
321
434
93.4
94.6
95.0
95.3
95.5
95.6
95.9
95.9
96.6
1028
1530
2021
2444
3060
3046
5105
5419
7185
0.90
0.93
0.96
0.90
0.96
0.95
0.95
1.00
0.97
1.2
1.3
1.4
1.6
1.5
1.8
1.5
1.6
1.5
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
520
520
520
520
520
520
520
520
520
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG707
3GBJ316230-_DG707
3GBJ316410-_DG707
3GBJ316820-_DG707
3GBJ316830-_DG707
3GBJ356220-_DG707
3GBJ356420-_DG707
3GBJ356820-_DG707
3GBJ406530-_DG707
79
105
168
205
259
228
357
431
548
93.9
94.8
95.3
95.5
95.7
95.7
95.8
96.1
96.5
956
1326
2091
2587
3295
3061
4420
5649
6612
0.91
0.94
0.92
0.93
0.93
0.99
0.91
0.96
0.88
1.3
1.4
1.4
1.5
1.4
1.7
1.8
1.7
1.8
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
645
645
645
645
645
645
645
645
645
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG708
3GBJ316230-_DG708
3GBJ316410-_DG708
3GBJ316820-_DG708
3GBJ316830-_DG708
3GBJ356220-_DG708
3GBJ356420-_DG708
3GBJ356820-_DG708
3GBJ406530-_DG708
116
164
206
255
301
296
513
509
701
94.7
95.5
95.8
95.7
96.0
95.7
96.3
96.3
97.0
997
1485
1929
2221
2813
2709
4797
4980
6728
0.89
0.93
0.96
0.89
0.96
0.94
0.95
1.00
0.97
1.3
1.3
1.4
1.7
1.6
2.0
1.6
1.7
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
863
863
863
863
863
863
863
863
863
650
880
1115
1415
1590
1765
2190
2670
3260
47
69
92
111
139
138
232
246
326
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
500 V
nn = 433 r/min
nn = 538 r/min
54
75
118
146
186
172
249
318
372
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
nn = 750 r/min
78
117
152
175
221
213
377
391
528
2)
2)
1)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
See ordering information - section for details on motor type and product
code
Performance values for IEC frame sizes 500 and 560 on request
3)
39
Product code1)
Current
IN
A
Efficiency
Full load
%
Torque
TN
Nm
Power
factor
cos
Torque
TN3)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Weight
approx.
kg
Tmax
nn = 183 r/min
16
24
37
45
61
61
81
101
122
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
3GBJ286220-_DG705
3GBJ316230-_DG705
3GBJ316410-_DG705
3GBJ316820-_DG705
3GBJ316830-_DG705
3GBJ356220-_DG705
3GBJ356420-_DG705
3GBJ356820-_DG705
3GBJ406530-_DG705
22
32
47
55
77
74
100
120
142
89.6
90.4
91.9
92.5
92.8
93.0
93.3
93.8
94.6
850
1277
1908
2333
3179
3172
4228
5289
6360
0.90
0.90
0.92
0.96
0.92
0.95
0.94
0.98
0.98
1.4
1.5
1.4
1.5
1.5
1.7
1.7
1.6
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
220
220
220
220
220
220
220
220
220
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG706
3GBJ316230-_DG706
3GBJ316410-_DG706
3GBJ316820-_DG706
3GBJ316830-_DG706
3GBJ356220-_DG706
3GBJ356420-_DG706
3GBJ356820-_DG706
3GBJ406530-_DG706
32
47
63
82
103
97
145
181
208
91.0
92.4
93.4
93.8
94.0
94.3
94.5
94.8
95.6
934
1399
1958
2486
3107
3101
4650
5733
6838
0.91
0.92
0.94
0.92
0.91
0.96
0.96
0.95
0.98
1.3
1.4
1.4
1.5
1.5
1.7
1.6
1.6
1.5
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
299
299
299
299
299
299
299
299
299
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG705
3GBJ316230-_DG705
3GBJ316410-_DG705
3GBJ316820-_DG705
3GBJ316830-_DG705
3GBJ356220-_DG705
3GBJ356420-_DG705
3GBJ356820-_DG705
3GBJ406530-_DG705
37
54
77
88
126
120
160
190
227
91.9
92.7
93.8
94.2
94.5
94.4
94.6
95.0
95.8
817
1221
1816
2196
2979
2946
3908
4887
5926
0.88
0.88
0.91
0.95
0.90
0.94
0.93
0.97
0.98
1.4
1.5
1.5
1.6
1.6
1.8
1.8
1.8
1.7
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
379
379
379
379
379
379
379
379
379
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG707
3GBJ316230-_DG707
3GBJ316410-_DG707
3GBJ316820-_DG707
3GBJ316830-_DG707
3GBJ356220-_DG707
3GBJ356420-_DG707
3GBJ356820-_DG707
3GBJ406530-_DG707
47
63
101
124
158
140
221
268
344
92.9
93.8
94.4
94.9
95.1
95.1
95.4
95.6
96.1
978
1367
2168
2711
3470
3249
4752
6055
7254
0.92
0.95
0.93
0.93
0.94
0.99
0.92
0.96
0.89
1.2
1.4
1.3
1.4
1.4
1.6
1.6
1.6
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
428
428
428
428
428
428
428
428
428
650
880
1115
1415
1590
1765
2190
2670
3260
nn = 249 r/min
24
37
51
65
81
81
121
150
178
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
nn = 316 r/min
575 V
27
40
60
73
99
98
129
162
196
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
nn = 357 r/min
37
51
81
101
130
121
178
226
271
2)
2)
1)
2)
40
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
See ordering information - section for details on motor type and product
code
Performance values for IEC frame sizes 500 and 560 on request
3)
Product code1)
Current
IN
A
Efficiency
Full load
%
Torque
TN
Nm
Power
factor
cos
Torque
TN3)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Weight
approx.
kg
Tmax
nn = 431 r/min
40
60
83
102
125
125
191
229
282
3)
3)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
3GBJ286220-_DG706
3GBJ316230-_DG706
3GBJ316410-_DG706
3GBJ316820-_DG706
3GBJ316830-_DG706
3GBJ356220-_DG706
3GBJ356420-_DG706
3GBJ356820-_DG706
3GBJ406530-_DG706
53
77
102
129
162
150
229
278
326
93.1
94.0
94.8
94.9
95.1
95.0
95.5
95.6
96.3
891
1327
1826
2251
2776
2760
4239
5076
6235
0.89
0.90
0.93
0.90
0.89
0.95
0.95
0.94
0.97
1.3
1.4
1.5
1.7
1.7
1.9
1.7
1.8
1.7
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
517
517
517
517
517
517
517
517
517
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG708
3GBJ316230-_DG708
3GBJ316410-_DG708
3GBJ316820-_DG708
3GBJ316830-_DG708
3GBJ356220-_DG708
3GBJ356420-_DG708
3GBJ356820-_DG708
3GBJ406530-_DG708
70
100
127
163
192
194
321
326
441
93.8
94.7
95.4
95.6
95.7
95.7
96.1
96.1
96.7
1044
1554
2053
2484
3109
3099
5194
5510
7302
0.89
0.93
0.96
0.90
0.96
0.95
0.95
1.00
0.97
1.2
1.3
1.3
1.5
1.5
1.8
1.5
1.5
1.5
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
598
598
598
598
598
598
598
598
598
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG707
3GBJ316230-_DG707
3GBJ316410-_DG707
3GBJ316820-_DG707
3GBJ316830-_DG707
3GBJ356220-_DG707
3GBJ356420-_DG707
3GBJ356820-_DG707
3GBJ406830-_DG707
75
99
158
190
240
209
327
394
503
94.3
95.1
95.4
95.6
95.8
95.7
95.8
96.1
96.5
912
1255
1968
2406
3061
2821
4000
5156
5984
0.91
0.94
0.92
0.93
0.93
0.99
0.90
0.96
0.87
1.3
1.5
1.5
1.6
1.5
1.8
1.9
1.8
1.9
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
742
742
742
742
742
742
742
742
742
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG708
3GBJ316230-_DG708
3GBJ316410-_DG708
3GBJ316820-_DG708
3GBJ316830-_DG708
3GBJ356220-_DG708
3GBJ356420-_DG708
3GBJ356820-_DG708
3GBJ406530-_DG708
109
153
188
224
265
253
460
446
624
94.8
95.6
95.8
95.4
95.8
95.3
96.3
96.1
96.9
931
1387
1765
1919
2474
2287
4294
4367
6011
0.89
0.93
0.96
0.88
0.96
0.93
0.95
1.00
0.97
1.4
1.4
1.5
2.0
1.8
2.4
1.8
1.9
1.8
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
863
863
863
863
863
863
863
863
863
650
880
1115
1415
1590
1765
2190
2670
3260
nn = 498 r/min
54
81
107
130
162
162
271
287
381
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
59
81
127
156
198
183
259
334
387
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LKC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
575 V
nn = 618 r/min
nn = 863 r/min
84
125
159
173
224
207
388
395
543
2)
2)
1)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
See ordering information - section for details on motor type and product
code
Performance values for IEC frame sizes 500 and 560 on request
3)
41
Product code1)
Current
IN
A
Efficiency
Full load
100 %
Torque
TN
Nm
Power
factor
cos
Torque
TN3)
Moment
of inertia
J=1/4GD2
kgm3
Maximum
speed,
nmax
r/min
Tmax
Weight
approx.
kg
nn = 220 r/min
20
30
45
55
75
75
99
124
149
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
3GBJ286220-_DG705
3GBJ316230-_DG705
3GBJ316410-_DG705
3GBJ316820-_DG705
3GBJ316830-_DG705
3GBJ356220-_DG705
3GBJ356420-_DG705
3GBJ356820-_DG705
3GBJ406530-_DG705
22
33
48
56
79
76
102
122
145
90.0
91.5
92.6
93.2
93.5
93.5
93.9
94.2
95.1
868
1306
1952
2385
3252
3250
4332
5418
6503
0.90
0.90
0.92
0.95
0.91
0.95
0.94
0.98
0.98
1.3
1.4
1.4
1.5
1.4
1.6
1.7
1.6
1.5
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
220
220
220
220
220
220
220
220
220
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG706
3GBJ316230-_DG706
3GBJ316410-_DG706
3GBJ316820-_DG706
3GBJ316830-_DG706
3GBJ356220-_DG706
3GBJ356420-_DG706
3GBJ356820-_DG706
3GBJ406530-_DG706
33
48
65
84
106
100
149
185
212
92.0
92.9
93.9
94.3
94.4
94.6
94.9
95.1
95.8
954
1431
2003
2544
3181
3177
4763
5881
6991
0.90
0.91
0.94
0.91
0.90
0.96
0.96
0.95
0.97
1.3
1.3
1.4
1.5
1.5
1.7
1.5
1.6
1.5
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
300
300
300
300
300
300
300
300
300
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG705
3GBJ316230-_DG705
3GBJ316410-_DG705
3GBJ316820-_DG705
3GBJ316830-_DG705
3GBJ356220-_DG705
3GBJ356420-_DG705
3GBJ356820-_DG705
3GBJ406530-_DG705
35
51
72
82
117
110
147
173
208
92.2
93.2
94.1
94.5
94.7
94.4
94.8
95.1
95.9
770
1145
1696
2032
2745
2688
3545
4444
5448
0.87
0.87
0.90
0.94
0.89
0.93
0.92
0.97
0.98
1.5
1.6
1.6
1.7
1.7
2.0
2.0
2.0
1.8
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
380
380
380
380
380
380
380
380
380
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG707
3GBJ316230-_DG707
3GBJ316410-_DG707
3GBJ316820-_DG707
3GBJ316830-_DG707
3GBJ356220-_DG707
3GBJ356420-_DG707
3GBJ356820-_DG707
3GBJ406530-_DG707
48
64
103
127
162
144
226
274
351
93.3
94.3
94.9
95.2
95.4
95.4
95.6
95.9
96.3
999
1398
2218
2773
3550
3329
4875
6210
7399
0.91
0.94
0.92
0.93
0.93
0.99
0.92
0.96
0.89
1.2
1.3
1.3
1.4
1.3
1.5
1.6
1.5
1.6
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
430
430
430
430
430
430
430
430
430
650
880
1115
1415
1590
1765
2190
2670
3260
nn = 300 r/min
30
45
63
80
100
99
149
184
219
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
nn = 380 r/min
31
46
67
81
109
107
141
177
217
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
nn = 430 r/min
690 V
45
63
100
124
159
149
219
279
332
2)
2)
1)
2)
42
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
See ordering information - section for details on motor type and product
code
Performance values for IEC frame sizes 500 and 560 on request
3)
Product code1)
Current
IN
A
Efficiency
Full load
%
Torque
TN
Nm
Power
factor
cos
Torque
TN3)
Moment
of inertia
J=1/4GD2
kgm2
Maximum
speed,
nmax
r/min
Tmax
Weight
approx.
kg
nn = 518 r/min
45
67
91
109
132
130
205
240
304
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
3GBJ286220-_DG706
3GBJ316230-_DG706
3GBJ316410-_DG706
3GBJ316820-_DG706
3GBJ316830-_DG706
3GBJ356220-_DG706
3GBJ356420-_DG706
3GBJ356820-_DG706
3GBJ406530-_DG706
49
72
93
116
145
132
206
245
292
93.4
94.4
94.9
94.9
95.0
94.9
95.5
95.5
96.4
833
1235
1675
2007
2442
2406
3786
4429
5605
0.89
0.90
0.93
0.89
0.87
0.94
0.95
0.93
0.98
1.4
1.6
1.6
1.9
1.9
2.2
1.9
2.1
1.8
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
518
518
518
518
518
518
518
518
518
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG708
3GBJ316230-_DG708
3GBJ316410-_DG708
3GBJ316820-_DG708
3GBJ316830-_DG708
3GBJ356220-_DG708
3GBJ356420-_DG708
3GBJ356820-_DG708
3GBJ406530-_DG708
72
102
130
167
197
199
329
334
451
94.4
95.1
95.6
95.7
95.9
95.9
96.2
96.2
96.9
1067
1590
2099
2543
3180
3178
5323
5639
7468
0.89
0.93
0.95
0.90
0.95
0.95
0.95
0.99
0.97
1.2
1.2
1.3
1.5
1.4
1.7
1.4
1.5
1.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
600
600
600
600
600
600
600
600
600
650
880
1115
1415
1590
1765
2190
2670
3260
3GBJ286220-_DG707
3GBJ316230-_DG707
3GBJ316410-_DG707
3GBJ316820-_DG707
3GBJ316830-_DG707
3GBJ356220-_DG707
3GBJ356420-_DG707
3GBJ356820-_DG707
3GBJ406530-_DG707
69
89
141
167
210
179
277
332
431
94.3
95.1
95.5
95.5
95.6
95.4
95.4
95.7
96.2
834
1134
1756
2092
2658
2409
3278
4313
4940
0.91
0.94
0.92
0.93
0.93
0.99
0.87
0.95
0.84
1.5
1.6
1.7
1.8
1.8
2.1
2.4
2.2
2.4
2.2
3.9
5.8
7.8
9.8
17.1
22.4
28.5
41.1
742
742
742
742
742
742
742
742
742
650
880
1115
1415
1590
1765
2190
2670
3260
nn = 600 r/min
67
100
131
159
199
199
333
353
467
2)
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
nn = 742 r/min
65
88
136
163
207
187
255
335
384
2)
690 V
2)
M3BJ 280SMB
M3BJ 315SMC
M3BJ 315MLA
M3BJ 315LKB
M3BJ 315LKC
M3BJ 355SMB
M3BJ 355MLB
M3BJ 355LKB
M3BJ 400LC
AMZ 0500L_10 RAM
AMZ 0560L_10 RAM
1)
2)
See ordering information - section for details on motor type and product
code
Performance values for IEC frame sizes 500 and 560 on request
3)
43
Variant
280
315
355 to 400
Balancing
424
037
039
041
042
Locked drive-end.
043
SPM nipples.
058
Angular contact ball bearing at D-end, shaft force away from bearing
059
060
061
107
108
420
701
209
419
425
785
Reinforced tropicalization.
183
422
791
035
Cooling system
068
Metal fan.
Coupling
Dimension drawing
141
065
066
076
Drain holes
Earthing bolt
067
450
451
Heating elements
1)
44
S
M
= Included as standard
= On modification of a stocked motor,
or on new manufacture,
the number per order may be limited.
P =
R =
NA =
Code1)
Variant
280
315
355 to 400
Insulation system
014
405
406
Mounting arrangements
009
IM 2001 foot/flange mounted, IEC flange, from IM 1001 (B35 from B3).
Noise reduction
055
Painting
111
114
115
179
Protection
072
073
005
401
403
783
135
138
139
150
161
163
070
155
156
164
165
410
427
431
1)
S = Included as standard
M = On modification of a stocked motor,
or on new manufacture,
the number per order may be limited.
P =
R =
NA =
New manufacture
On request.
Not applicable
45
Code1)
Variant
280
315
355 to 400
122
123
125
127
435
436
437
439
441
442
445
446
Terminal box
015
017
019
021
180
137
230
400
402
413
418
466
704
729
731
743
744
Testing
148
760
761
762
763
764
1)
Certain variant codes cannot be used simultaneously.
only.
46
S = Included as standard
M = On modification of a stocked motor,
or on new manufacture,
the number per order may be limited.
P =
R =
NA =
New manufacture
On request.
Not applicable
Code1)
Variant
280
315
355 to 400
422
470
479
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
Separate motor cooling (fan axial, N-end) and 1024 hollow shaft pulse tacho
(Leine & Linde equivalent)
Separate motor cooling (fan axial, N-end) and 2048 hollow shaft pulse tacho
(Leine & Linde equivalent)
Separate motor cooling (fan axial, N-end) and Lake Shore RIM 8500 pulse
tacho mounted.
Separate motor cooling (fan axial, N-end) and Avtron M285 pulse tacho
mounted.
576
Separate motor cooling (fan axial, N-end) and 1024 pulse tacho (L&L 562).
577
Separate motor cooling (fan axial, N-end) and 2048 pulse tacho (L&L 562).
580
Separate motor cooling, IP 44, 400 V, 50 Hz (fan axial, N-end) and 1024
pulse tacho (Leine & Linde 562).
581
Separate motor cooling, IP 44, 400 V, 50 Hz (fan axial, N-end) and 2048
pulse tacho (Leine & Linde 562).
570
062
471
472
473
572
573
748
749
474
478
574
578
486
487
428
429
430
475
476
477
488
489
1)
S
M
= Included as standard
= On modification of a stocked motor,
or on new manufacture,
the number per order may be limited.
P =
R =
NA =
47
Bearing shields
Stator winding
Form wound copper
Insulation class F (155 C)
Winding protection: Pt-100 6 pieces, 3-wire connection
Bearings
Ball bearings
Bearing insulation at N-end
Bearings protection: Pt-100 1 pcs/bearing, 3-wire
connection
500
IM 1001: D-end 6330/C3, N-end 6330/C3
IM 3011: D-end 6330/C3, N-end 7330 BM
560
IM 1001: D-end 6338/C3, N-end 6338/C3
IM 3011: D-end 6338/C3, N-end 7338 BM
Bearing seal
Labyrinth seal in both ends
Rotor
Permanent magnet rotor
Shaft
One open keyway
Shaft material: 42CrMo4 - EN 10083
Balancing
Rotor balanced with half key according to ISO 1940/1
- Balancing grade G2.5
Drain holes
Drain holes at lowest part of the machine- IM 1001
2 pcs in frame
- IM 3011
2 pcs in D-end shield
Cooling
IC411
IC416 (axially mounted blower unit)
Lubrication
Regreasable bearings
Grease nipple M10x1 DIN 71412
Mounting
IM 1001 (horizontal machine)
IM 3011 (vertical machine, shaft downwards)
SPM-nipples
1 pcs/bearing
Ambient temperature
-20 to +40C
Altitude
1000 m above sea level
Connections
Cable entries:
- Undrilled gland plate
- Roxtec EMC cable entry
- Grounding locations on frame and terminal box
(in- and outside)
Material: aluminium
Cable entries: M20 x 1.5 (2 pcs)
Cable glands: included as standard
- Material: nickel plated brass
Fan
Structural steel S235JRG2 EN 10025
Protection
IP55
Application related standards:
EMC
Painting
Paint System 1
- Standard BS 5493
- Colour Munsell 8B 4.5/3.25 / NCS 4822 B05G
- Two-pack epoxy paint, thickness 180 m
Standard documentation
Dimension drawing
Connection diagram (main, auxiliary)
Performance data of motor
Maintenance manual
Routine test report
Standard tests
Fan cover
Structural steel S235JRG2 EN 10025,
thickness 3 mm
48
Routine test
Permanent magnet motors, optional construction for motors 500 and 560
Optional specification
Mounting
IM 1002
- Max. torque limited for N-end shaft
IM 2001
Cooling
IC 416
- top mounted blower unit, only for horizontal machines
IC 417
Ambient temperature
Min limit -50 to -20 C, to be checked case by case
Max limit +40 to +60 C, to be checked case by case
Protection
IP56
Optional constructions
Balancing
BL-SET
- Rotor balanced with full key
Shaft
CM-SET
- Machined coupling half, mounting only
Bearings
IN-SET1
- Inpro-seal in D-end
IN-SET2
- Inpro-seal in N-end
IN-SET3
- Inpro-seal in D- and N-end
GC-SET
- Grease collector in D- and/or N-end
IB-SET
- Both bearings insulated, earth strap in D-end
TL-SET
- Transport locking device
MT-SET1
- Main terminal box in N-end (horizontal machines)
MG-SET1
- Cable glands for supply cables: Hawke
MG-SET2
- Provision for cable glands (no Roxtec): M-threads
AS-SET
- Separate terminal box for space heater and RTDs
AM-SET
- Special material: stainless steel AISI 304
AG-SET1
- Cable glands for control cables: Hawke
Others
PS-SET2
- Paint system 2
PS-SET4
- Paint system 4
DH-SET
- Threaded drain plug in frame
SS-SET
- Bolts, nuts and washers made of stainless steel
Optional accessories
Control and protective equipment
General
RT-SET1
- RTDs with 4-wire connection
RT-SET2
- Duplex RTDs with 4-wire connection
Winding
PY-SET1
- Termistors (PTC), 3 pcs set temperature 150 C
and 3 pcs 170 C.
TT-PT100-SET1
- Transmitters for Pt-100, 3 pcs
Bearings
AFB-TCK-SET1
- Thermocouples, 1 pcs/bearing, type K (NiCr-Ni)
AFB-TCT-SET1
- Thermocouples, 1 pcs/bearing, type T (Cu-CuNi)
AFB-TCJ-SET1
- Thermocouples, 1 pcs/bearing, type J (Fe-CuNi)
AFB-TCE-SET1
- Thermocouples, 1 pcs/bearing, type E (NiCr-CuNi)
TT-PT100-SET2
- Transmitters for Pt-100 3 pcs for windings and 1 pc for each
bearing
TT-TC-SET1
- Transmitters for thermocouple, 1 pc for each bearing
AFB-DAT-SET1-HX
- Dial type thermometer without contacts, 1 pcs/bearing
AFB-DATC-SET1
- Dial type thermometer with contacts, 1 pcs/bearing
Heating elements
Single phase, 50/60 Hz, 400 W (AMZ 0500)
or 500 W (AMZ 0560)
RE-SET1
- Voltage range: 220 to 250 V
RE-SET2- Voltage range: 110 to 120 V
RE-SET3
- Voltage range: 380 to 440 V
49
Pulse encoder
ABB standard type
TAC-SET1
- Pulse rate 1024 ppr
TAC-SET2
- Pulse rate 2048 ppr
Vibration transducers
VIB-SPM-SET2-HX
- Seismic type accelerometers mounted on the end shields,
2 pcs. Measuring direction horizontal.
VIB-SPM-SET3-HX
- 1 pc accelerometer mounted on end shield. Measuring
direction axial.
Special construction
Note! All special constructions must be checked at the factory
case by case.
Special specification
Cooling
IC 71W
- Water cooled, welded frame construction
Special constructions
Shaft
Others
RC-SET
- Rain canopy for vertical machines
Optional documentation
Main terminal box drawing
Auxiliary terminal box drawing
Rotor drawing
Optional tests
50
SE-SET1
- Special shaft extension at D-end, only motor size 500 (not
applicable for foot- and flange mounted machine):
D=160 mm, E=300 mm
SE-SET2
- Smaller shaft extension at D-end.
TE-SET
- Tapered shaft
Others
BR-SET1
- Brakes
BR-SET2
- Backstops
Type test
Sizes 280-315
Motor
size
AA
AB
AC
BA
BB
CA
530
577
368
419
147
506
190
400 349 -
590
654
406
457
180
558
216
315 ML_
508 100
590
654
457
508
212
669
216
315 LK_
508 100
590
654
508
560
710 336
851
216
Motor
size
FA
GA
280 SM_
20
18
67.5
79.5 58
315 SM_
22
20
71
85
315 ML_
25
20
81
95
315 LK_
25
20
81
95
DB
75
65
420 369 -
80
480 429 -
90
90
DC
EA
EG
EH
40
40
75
40
40
75
48
40
75
48
40
GD
GF
HA HC
HD 1)
HD 2)
LC
LD
69
12
11
280
31
564
762
24
1088
1236
336
100
67.5 79.5 14
12
315
40
639
852
28
1204
1352
386
115
67.5 79.5 14
12
315
40
639
852
28
1315
1463
386
115
67.5 79.5 14
12
315
40
639
852
880
28
1521
1669
386
115
1)
2)
0,8
0.8
ISO k6 < 50mm
ISO m6 > 50mm
DA
GC
GB
Tolerances:
A, B
C, CA
D
CA CA D
F
H
N
ISO h9
+0 -0.5
ISO j6
51
Sizes 355-400
Motor
size
355 SM_
355 ML_
355 LK_
400 L_
AA
AB
AC
BA
BB
CA
CA
CA D
500
560
221
722
254
525
465
100 90
560
630
267
827
254
500
570
100 90
630
710 900
447
1077
254
750
670
480
900
410
1156
224
567
467
1000
DA
DB
DC
EA
EG EH
M24 M24
210
170
50
48
M24 M24
210
170
50
48
100 90
M24 M24
210
170
50
48
110 90
M24 M24
210
170
50
48
Motor
size
FA
GA
GB
GC
GD
GF
HA
HC
HD 1)
HD 2)
LC
LD
355 SM_
28
25
90
106
81
95
16
14
355
52
725
944
958
35
1479
1659
467
130
355 ML_
28
25
90
106
81
95
16
14
355
52
725
944
958
35
1584
1764
467
130
355 LK_
28
25
90
106
81
95
16
14
355
52
725
944
958
35
1834
2014
467
130
400 L_
28
25
100
116
81
95
16
14
400
45
814
1045
35
1891
2071
498
150
1)
Tolerances:
A, B
C, CA
D
2)
0,8
0.8
ISO k6 < 50mm
ISO m6 > 50mm
F
H
N
ISO h9
+0 -0.5
ISO j6
52
Motor
size
AA
AB
AC
BA
BB
DB
EG
280 SM_
457
84
530
577
368
419
147
506
190
75
M20
140
40
20
315 SM_
508
100
590
654
406
457
180
558
216
80
M20
170
40
22
315 ML_
508
100
590
654
457
508
212
669
216
90
M24
170
48
25
315 LK_
508
100
590
654
508
560
710
336
851
216
90
M24
170
48
25
Motor
size
GA
GD
HA
HC
HD 1)
HD 2)
LC
LD
280 SM_
67.5
79.5
12
280
31
564
762
24
1194
1472
336
25
315 SM_
71
85
14
315
40
639
852
28
1304
1582
386
25
315 ML_
81
95
14
315
40
639
852
28
1414
1692
386
25
315 LK_
81
95
14
315
40
639
852
880
28
1638
1950
386
25
1)
Tolerances:
A, B
C, CA
D
2)
0,8
0.8
ISO k6 < 50mm
ISO m6 > 50mm
F
H
N
ISO h9
+0 -0.5
ISO j6
Above table gives the main dimensions in mm.
For detailed drawings please see our web site
'www.abb.com/motors&drives' or contact us.
53
Motor
size
AA
AB
AC
BA
BB
DB
EG
355 SM_
610
120
700
746
500
560
221
722
254
100
M24
210
50
28
355 ML_
610
120
700
355 LK_
610
120
700
746
560
630
267
827
254
100
M24
210
50
28
746
630
710
900
447
1077
254
100
M24
210
50
28
400 L_
710
150
840
834
900
1000
410
1156
224
110
M24
210
50
28
GA
GD
HA
HC
HD 1)
HD 2)
LC
LD
355 SM_
90
106
16
355
52
725
944
958
35
1594
1905
467
25
355 ML__
90
106
16
355
52
725
944
958
35
1699
2056
467
25
355 LK_
90
106
16
355
52
725
944
958
35
1953
2310
467
25
100
116
16
400
45
814
1045
35
1996
2353
498
25
Motor
size
400 L_
1)
Tolerances:
A, B
C, CA
D
0,8
0.8
ISO k6 < 50mm
ISO m6 > 50mm
F
H
N
ISO h9
+0 -0.5
ISO j6
2)
54
Motor
size
AA
AB
AC
BA
BB
DB
EG
280 SM_
457
84
530
577
368
419
147
506
190
75
M20
140
40
20
315 SM_
508
100
590
654
406
457
180
558
216
80
M20
170
40
22
315 ML_
508
100
590
654
457
508
212
669
216
90
M24
170
48
25
315 LK_
508
100
590
654
508
560
710
336
851
216
90
M24
170
48
25
H1
HD 1)
HD 2)
Motorsize
GA
GD
HA
HC
280 SM_
67.5
79.5
12
280
31
564
762
1245
24
1043
1333
336
130
25
315 SM_
71
85
14
315
40
639
852
1316
28
1246
1535
386
130
25
315 ML_
81
95
14
315
40
639
852
1316
28
1356
1645
386
130
25
315 LK_
81
95
14
315
40
639
852
880
1316
28
1516
1805
386
130
25
1)
Tolerances:
A, B
C, CA
D
2)
0,8
0.8
ISO k6
ISO m6 > 50mm
F
H
N
ISO h9
+0 -0.5
ISO j6
LD
55
Motor
size
AA
AB
AC
BA
BB
DB
EG
355 SM_
610
120
700
746
355 ML_
610
120
700
746
500
560
221
722
254
100
M24
210
50
28
560
630
267
827
254
100
M24
210
50
28
355 LK_
610
120
700
746
400 L_
710
150
840
834
630
710
900
447
1077
254
100
M24
210
50
28
900
1000
410
1156
224
110
M24
210
50
28
Motorsize
GA
GD
HA
HC
HD 1)
HD 2)
H1
LD
355 SM_
90
106
16
355
52
725
944
958
1500
35
1514
1771
467
130
25
355 ML_
90
106
16
355
52
725
355 LK_
90
106
16
355
52
725
944
958
1500
35
1584
1841
467
130
25
944
958
1500
35
1834
2091
467
130
25
400 L_
100
116
16
400
45
814
1045
1593
35
1891
2148
498
130
25
1)
Tolerances:
A, B
C, CA
D
0,8
0.8
ISO k6
ISO m6 > 50mm
F
H
N
ISO h9
+0 -0.5
ISO j6
2)
56
Sizes 280-315
Motor
size
AA
AB
AC
BA
BB
D1)
DB
EG
280 SM_
457
85
530
544
368
419
135
470
190
75
M20
140
40
315 SM_
508
100
590
615
406
457
130
537
216
80
M20
170
40
315 ML_
508
100
590
615
457
508
130
588
216
90
M24
170
48
315 LK_
508
100
590
615
508
710
130
805
216
90
M24
170
48
Motor
size
GA
GD
HA1)
HD
LD
280 SM_
20
67.5
79.5
12
280
40
745
24
932
332
390
300
315 SM_
22
71
85
14
315
50
840
30
1042
381
440
350
315 ML_
25
81
95
14
315
50
840
30
1093
381
440
400
315 LK_
25
81
95
14
315
50
840
30
1310
381
440
420
1)
Tolerances:
D ISO m6
H ISO 0, -1.0
57
Sizes 355-400
Motor
size
AA
AB
AC
BA
BB
DB
EG
355 SM_
610
120
700
700
500
560
161
667
254
100
M24
210
190
48
355 ML_
610
120
700
700
560
630
161
772
254
100
M24
210
190
48
355 LK_
610
120
700
700
630
900
161
1028
254
100
M24
210
190
45
400 L_
3)
Motor
size
GA
GD
HA1)
HD
355 SM_
28
90
106
16
355
55
955
35
1282
467
530
450
180
355 ML_
28
90
106
16
355
55
955
35
1387
467
530
550
180
355 LK_
28
90
106
16
355
55
955
35
1643
467
530
800
180
400 L_
3)
1)
2)
3)
Tolerances:
D ISO m6
H ISO 0, -1.0
Note: Motor sizes 355 to 400 with a bearing
fan.
On request
LD
Z2)
58
Top-mounted
Terminal boxes 210, 370
A1
B1
H1
210
416
306
177
370
451
347
200
750 top-mounted
686
413
219
For motor dimensions please see dimension drawings on earlier pages or on our
web site 'www.abb.com/motors&drives'.
59
Motor
AMZ
Poles
AA
AB
AC
AE
BA
BB
GD
0500L
10
900
170
1050
1035
1265
1570
375
1250
280
140
250
36
128
20
500
0560L
10
1000
230
1170
1190
1340
1940
620
1600
400
180
300
45
165
25
560
Motor
AMZ
HA
HD
LD
LE
LF
0500L
45
1530
42
2535
1880
540
200
0560L
50
1675
48
3065
2350
630
250
60
Motor
AMZ
Poles
AC
AD
AE
GD
HD
LA
LD
LE
LF
0500L
10
1040
1175
1085
140
250
36
128
20
1750
2535
30
550
1890
200
0560L
10
1190
1260
1170
180
300
45
165
25
1965
3065
60
650
2370
250
Motor
AMZ
0500L
1080
1000
1150
28
0560L
1320
1250
1400
28
61
Motor
AMZ
Poles
AA
AB
AC
AE
BA
BB
GD
0500L
10
900
170
1050
1035
1265
1570
375
1250
280
140
250
36
128
20
500
0560L
10
1000
230
1170
1190
1340
1940
620
1600
400
180
300
45
165
25
560
Motor
AMZ
HA
HD
LD
LE
LG
LF
0500L
45
1530
42
1880
540
2850
310
0560L
50
1675
48
2350
630
3410
300
62
Motor
AMZ
Poles
AC
AD
AE
GD
HD
LA
LD
LE
0500L
10
1040
1175
1085
140
250
36
128
20
1750
30
550
1890
0560L
10
1190
1260
1170
180
300
45
165
25
1965
60
650
2370
Motor
AMZ
LF
LG
0500L
310
2850
1080
1000
1150
28
0560L
300
3410
1320
1250
1400
28
63
Motor
AMZ
Poles
0500L
AA
AB
AC
AE
BA
BB
10
900
170
1050
1050
1325
1570
375
1250
280
140
250
36
128
0560L
10
1000
230
1170
1200
1345
1940
620
1600
400
180
300
45
165
Motor
AMZ
GD
HA
HD
HT
LD
LE
LF
0500L
20
500
45
1530
2280
42
2525
1880
540
200
0560L
25
560
50
1675
2400
48
3055
2350
630
250
64
Motor
AMZ
Poles
AA
AB
AC
AE
BA
BB
0500L
10
900
170
1050
920
1265
1600
390
1250
280
140
250
36
128
0560L
10
1000
230
1170
1040
1300
1940
620
1600
400
180
300
45
165
Motor
AMZ
GD
HD
LD
LE
0500L
20
500
1530
2195
1915
540
746
1056
0560L
25
560
1675
2830
2395
655
836
1446
65
Motor
AMZ
Poles
AC
AD
AE
GD
HD
LA
LD
0500L
10
1020
1175
1080
140
250
36
128
20
1750
2160
30
475
0560L
10
1150
1260
1170
180
300
45
165
25
1965
2800
60
605
Motor
AMZ
LE
0500L
1830
1080
1000
1150
28
746
1056
0560L
2345
1320
1250
1400
28
718
1446
66
280
315
355
400
500
560
Material
Paint
Paint thickness
70 m
180 m
Material
Paint thickness
D-end
6316/C3
6319/C3
6322/C3
6324/C3
6330/C3
6338/C3
N-end
6316/C3
VL024
6316M/C3
VL024
6316M/C3
VL024
6319M/C3
VL024
IM 1001:
6330/C3
IM 3011:
7330 BM
IM1001:
6338/C3
IM 3011:
7338 BM
Bearing seals
Lubrication
SPM-nipples
As standard
Bearing end
shields
Bearings
Axially-locked
bearings
180 m
Rating plate
Material
Terminal box
Frame material
Structural steel,
S235JRG2- EN 10025,
thickness 3 mm
Cover material
Structural steel,
S235JRG2- EN 10025,
thickness 3 mm
Connections
Fan
Material
Structural steel,
S235JRG2- EN 10025
Fan cover
Material
Steel
Structural steel,
S235JRG2- EN 10025,
thickness 3 mm
Stator winding
Rotor winding
Paint
Paint thickness
80 m
180 m
Material
Copper
Insulation
Insulation class F
Winding protection
Material
Balancing method
Key way
Heating elements
On request
50 W
2x50 W
2x65 W
Drain holes
Enclosure
Cooling method
IC 411, IC 416
2x65 W
400 W
500 W
67
Notes
68
Notes
69
Other applications
Motors for hazardous areas
Marine motors
Permanent magnet motors
High speed motors
Wind turbine generators
NEMA motors
Water cooled motors
Motors for roller table drives
Slip ring motors
Wood dryer motors
Fan application motors
Aluminum motors
Cast iron motors
70
71
Austria
ABB AG
Wienerbergstrasse 11 B
AT-1810 Wien
Tel: +43 (0) 1 601 090
Fax: +43 (0) 1 601 09 8305
Belgium
Asea Brown Boveri S.A.-N.V.
Hoge Wei 27
BE-1930 Zaventem
Tel: +32 (0) 2 718 6311
Fax: +32 (0) 2 718 6657
Canada
ABB Inc., BA Electrical Machines
10300 Henri-Bourassa Blvd, West,
Saint-Laurent, Quebec
Canada H4S 1N6
Tel: +1 514 832-6583
Fax: +1 514 332-0609
China*
ABB Shanghai Motors
Company Limited
8 Guang Xing Rd.,Rong Bei
Town, Songjiang County,
Shanghai 201613
Tel: +86 21 5778 0988
Fax: +86 21 5778 1364
Chile
Asea Brown Boveri S.A.
P.O.Box 581-3
Santiago
Tel: +56 (0) 2 5447 100
Fax: +56 (0) 2 5447 405
Denmark
ABB A/S
Automation Technology Electrical
Machines
Petersmindevej 1
DK-5000 Odense C
Tel: +45 65 477 070
Fax: +45 65 477 713
Finland*
ABB Oy
LV Motors
P.O.Box 633
FI-65101 Vaasa
Tel: +358 (0) 10 22 11
Fax: +358 (0) 10 22 47372
http://www.abb.com/motors&drives
http://online.abb.com/motors&drives
France
ABB Automation
Rue du Gnral de Gaulle
Champagne-sur-Seine
FR-77811 Moret-sur-Loing
Cedex
Tel: +33 (0) 1 60 746 500
Fax: +33 (0) 1 60 746 565
Germany
ABB Automation Products GmbH
Edisonstrasse 15
DE-68623 Lampertheim
Tel: +49 (0) 6206 503 503
Fax: +49 (0) 6206 503 600
Hong Kong
ABB (Hong Kong) Ltd.
Tai Po Industrial Estate,
3 Dai Hei Street,
Tai Po, New Territories,
Hong Kong
Tel: +852 2929 3838
Fax: +852 2929 3505
India*
ABB Ltd.
32, Industrial Area, N.I.T
Faridabad 121 001
Tel: +91 (0) 129 502 3001
Fax: +91 (0) 129 502 3006
Korea
ABB Korea Ltd.
7-9fl, Oksan Bldg., 157-33
Sungsung-dong, Kangnam-ku
Seoul
Tel: +82 2 528 2329
Fax: +82 2 528 2338
Malaysia
ABB Malaysia Sdn. Bhd.
Lot 608, Jalan SS 13/1K
47500 Subang Jaya, Selangor
Tel: +60 3 5628 4888
Fax: +60 3 5631 2926
Mexico
ABB Mxico, S.A. de C.V.
Apartado Postal 111
CP 54000 Tlalnepantla
Edo. de Mxico, Mxico
Tel: +52 5 328 1400
Fax: +52 5 390 3720
The Netherlands
ABB B.V.
Dept. LV motors (APP2R)
P.O.Box 301
NL-3000 AH Rotterdam
Tel: +31 (0) 10 4078 879
Fax: +31 (0) 10 4078 345
Indonesia
PT. ABB Sakti Industri
JL. Gajah Tunggal Km.1
Jatiuwung, Tangerang 15136
Banten, Indonesia
Tel: + 62 21 590 9955
Fax: + 62 21 590 0115 - 6
Norway
ABB AS
Automation Technology Products
Division
P.O.Box 6540 Rodeloekka
NO-0501 Oslo 5
Tel: +47 22 872 000
Fax: +47 22 872 541
Ireland
Asea Brown Boveri Ltd
Components Division
Belgard Road
Tallaght, Dublin 24
Tel: +353 (0) 1 405 7300
Fax: +353 (0) 1 405 7327
Singapore
ABB Industry Pte Ltd
2 Ayer Rajah Crescent
Singapore 139935
Tel: +65 6776 5711
Fax: +65 6778 0222
Italy*
ABB SACE SpA
LV Motors
Via Della Meccanica, 22
IT-20040 Caponago - MI
Tel: +39 02 959 6671
Fax: +39 02 959 667216
Japan
ABB K.K.
26-1 Cerulean Tower
Sakuragaoka-cho, Shibuya-ku
Tokyo 150-8512
Tel: +81 (0) 3 578 46251
Fax: +81 (0) 3 578 46260
Spain*
ABB Automation Products S.A.
Division Motores
P.O.Box 81
ES-08200 Sabadell
Tel: +34 93 728 8500
Fax: +34 93 728 8741
Sweden*
ABB Automation Technologies AB
LV Motors
SE-721 70 Vsters
Tel: +46 (0) 21 329 000
Fax: +46 (0) 21 124 103
Switzerland
ABB Schweiz AG
Normelec/CMC Components
Motors&Drives
Badenerstrasse 790
Postfach
CH-8048 Zrich
Tel: +41 (0) 58 586 0000
Fax: +41 (0) 58 586 0603
Taiwan
ABB Ltd.
6F, No. 126, Nanking East Road,
Section 4i
Taipei, 105 Taiwan, R.O.C.
Tel: +886 (0) 2 2577 6090
Fax: +886 (0) 2 2577 9467
Thailand
ABB Limited (Thailand)
161/1 SG Tower,
Soi Mahadlekluang 3,
Rajdamri, Bangkok 10330
Tel: +66 2 665 1000
Fax: +66 2 6042
The United Kingdom
ABB Automation Ltd
9 The Towers, Wilmslow Road
Didsbury
Manchester, M20 2AB
Tel: +44 (0) 161 445 5555
Fax: +44 (0) 161 448 1016
USA
ABB Inc.
Electrical Machines
P.O.Box 372
Milwaukee
WI 53201-0372
Tel: +1 262 785 3200
Fax: +1 262 785 8628
Venezuela
Asea Brown Boveri S.A.
P.O.Box 6649
Carmelitas,
Caracas 1010A
Tel: +58 (0) 2 238 2422
Fax: +58 (0) 2 239 6383
Australia
ABB Industry Pty Ltd
2 Douglas Street
Port Melbourne,
Victoria, 3207
Tel: +61 (0) 3 9644 4100
Fax: +61 (0) 3 9646 9362