Beruflich Dokumente
Kultur Dokumente
Rear derailleur
1. Direct mount dropout dimensions
Note1: Horizontal Line D goes thru BB center and FH center. Note2: The drawings are for Rigid frame, but in case of rear suspension type, Line D should be determined by riding height such as 1G sag. Line D needs to go thru BB center and FH center, also. Note3: SM-AX75,60 are not recommended for downhill usage.
Frame Requirement
M981 /
NE
M786 /
W NE
M781 /
NE
M675 /
NE
M670 >
32.2
10
Line D
31
R25
9.4MIN 25
R1
65 3
+0
C1 8 0.2
+0
C1
R7.5
(MAX
R8)
12
MAX LINE
R1
M10x1.0-6H
23.
1-R
1.5
311
45
+4 0
All information on this page as of Feb. 6th 2012. version 1.0 Last updated: Feb 6, 2012
15
31
R25
19 0
.5
+0.1
C0
9.4MIN 25
65 3
+0
AX
R7.5
R1
(MAX
R8)
12
MAX LINE
Ar
ea
(9
12
311
+0.2 +0.05
MAX R2.5
R1
M10x1.0-6H
5 23.
D
1-R
.5
4.5 1
+0
+0
R1
2.5
C1
C1
16
version 1.0 Last updated: Feb 6, 2012
C0
.5
Frame Requirement
32.21
Line D
32.21 A
3.5 0.1
+0
t1*
9 5MIN M4
MA XR 15
45
+4 0
Frame Requirement
29.141
Line D
40.271
.5
8.1MIN
87.6 3
+0
2.4
C1 8
+0 0.2
C1
R7.5
(MAX
R8)
R1
1-R
MAX LINE
12
M10x1.0-6H 8 0.2
+0
40.27 1
R12
R25
10
or
12
29.141
60
+4 0
All information on this page as of Feb. 6th 2012. version 1.0 Last updated: Feb 6, 2012
17
40.271
11.5 1
8.1MIN
C
87 .6
+0 3
B
60 0
+4
MAX LINE
40.271
2.4
.5 R7
(M
8 XR
12
AX
R1
1-R
R1
MAX LINE
Ar
ea
(9
12
12
19 0
+0
.5
+0.1
C0
R25
+0.2 +0.05
4.5 1
+0
+0
46.6
1.5
R1
2.5
C1
C1
18
version 1.0 Last updated: Feb 6, 2012
C0
.5
Frame Requirement
29.141
Line D
+0
t1*
9 5MIN M4
MA
XR
15
Frame Requirement
t2
12 +0.2 +0.05
* t1+t2=16 0.5
3.5 -0.1
+0
t1
*
9
C0 .5
C0.5
.5 C0
R2.5 M4 5 MIN
+0.2 +0.05
12
1 MAX
3.5 +0 -0.1
7~8
(RD Hanger) HUB L/H SIDE SURFACE HUB R/H SIDE SURFACE
<INSIDE>
2-2. Other information about E-thru rear freehub (FH-M988/ WH-M988-R12/FH-M788/WH-M788-R12/FH-M678/WH-MT68-R12/ WH-MT66-R12-29) 12 mm thru axle
Total dropout thickness should be less than 16 0.5mm . Charts SM-AX75 adjust nut keeper section is design example . SM-AX75 specification is lever axle with adjust nut set . SM-AX75 total axle length is 171mm specification only . About clearance between the smallest sprocket (top gear) and dropout is explained at page 6. Dropout configuration and SHIMANO SHADOW RD dropout dimension are explained at page 20 and 21 Disc brake mount dimensions are explained at page 10. There are variety of frame design as well as tire width, so when deciding frame dimensions, please be put attention of rear wheel install and removal operation . Upper drawing shows an example of dropout and nut keeper. Please design and consider for dropout and nut keeper as a whole by your frame design. Please design nut keeper section which doesnt give side force to adjust nut . If adjust nut is given unnecessary side force, SM-AX75 screwing and rescrewing operation will be heavy .
19
+0.1 -0
.5 C0
All information on this page as of Feb. 6th 2012. version 1.0 Last updated: Feb 6, 2012
19