Beruflich Dokumente
Kultur Dokumente
CONTENTS
1 Introduction .............................................................................. 3
1.1 Equipment ................................................................................. 4 1.2 General Cautions...................................................................... 5 1.3 Adhesives ................................................................................. 5
2 Disassembly ............................................................................. 6
2.1 Overview ................................................................................... 6
2.1.1 2.1.2 2.1.3 2.1.4 2.1.5 2.1.6 2.1.7 2.1.8 2.1.9 2.1.10 2.1.11 2.1.12 Battery Cover Assembly & Battery ........................................ 7 Screw Cover Coated ............................................................. 8 Co-Brand Label ..................................................................... 9 Antenna Cover Assembly .................................................... 10 Speakerbox Assembly ......................................................... 15 PBA incl. Card Reader Assembly ........................................ 16 Card Reader Assembly ....................................................... 18 Sliding Lens Cover .............................................................. 19 Top Rear Inner Panel Assy ................................................. 21 Keyboard ............................................................................. 22 Dome Foil ............................................................................ 23 Keyboard FPC Assembly .................................................... 24
3 Replacements ......................................................................... 26
3.1 Battery Cover Assembly & Battery ....................................... 27 3.2 Screw Cover Coated .............................................................. 27 3.3 Co-Brand Label ....................................................................... 27 3.4 Antenna Cover Assembly ...................................................... 27 3.5 Speakerbox Assembly ........................................................... 27 3.6 Card Reader Assembly .......................................................... 27 3.7 Sliding Lens Cover ................................................................. 27 3.8 Plastic Slider Snap ................................................................. 28 3.9 Top Rear Inner Panel Assy .................................................... 28 3.10 Keyboard ................................................................................. 28 3.11 Dome Foil ................................................................................ 28 3.12 Keyboard FPC Assembly....................................................... 28 3.13 Gasket for Keyboard BtB....................................................... 28 3.14 Foil Adhesive Double Side 0.0 mm Adhesive Keyboard Flex 28 3.15 Frame Assy ............................................................................. 29 3.16 Top Front Outer Panel Assy .................................................. 30
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB 1(66)
3.17 Carrier Top Front Inner Panel Assy ...................................... 31 3.18 Ear Speaker ............................................................................. 32 3.19 5MP Camera & Cushion ......................................................... 33 3.20 Qcif VGA Camera & Camera Gasket .................................... 37 3.21 Shield Can Lid BB 1 & Conductive Gaskets ........................ 38 3.22 Shield Can Lid BB 2 ............................................................... 39 3.23 MComp Sheet Metal ............................................................... 40 3.24 BT Antenna ............................................................................. 41 3.25 Side Keys ................................................................................ 42 3.26 MComp Spring Metal pogo spring ........................................ 43 3.27 Liquid Intrusion Indicators .................................................... 44 3.28 Display & Touch Sensor FPC Assy & Light diffusion film . 45 3.29 Core Unit Label ....................................................................... 48
4 Reassembly ............................................................................ 49
4.1 Overview ................................................................................. 49
4.1.1 4.1.2 4.1.3 4.1.4 4.1.5 4.1.6 4.1.7 4.1.8 4.1.9 4.1.10 4.1.11 4.1.12 Keyboard FPC Assembly .................................................... 50 Dome Foil ............................................................................ 52 Keyboard ............................................................................. 53 Top Rear Inner Panel Assy ................................................. 54 Sliding Lens Cover .............................................................. 55 Card Reader Assembly ....................................................... 56 PBA incl. Card Reader Assembly ........................................ 57 Speakerbox Assembly ......................................................... 59 Antenna Cover Assembly .................................................... 60 Co-Brand Label ................................................................... 62 Screw Cover Coated ........................................................... 63 Battery & Battery Cover Assembly ...................................... 65
2(66)
Introduction
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
3(66)
1.1 Equipment
SPECIAL TOOLS
NTZ 122 459 NTZ 122 288 NTZ 112 1052 NTZ 112 302/2 NTZ 122 521 NTZ1121077 NTZ 112 590 Torque screwdriver (or equivalent) Bits (T6) Bits (PH00) Front opening tool Flex film assembly tool Camera Tool Guitar Pick
STANDARD TOOLS
Dentist hook ESD tweezers
ESD EQUIPMENT
Protect the phone from ESD damages whenever it has been opened by using: ESD-wristband ESD-gloves
LABEL EQUIPMENT
The following special equipment is required when replacing or installing a new label: Hot air flow solder station Zebra printer connected to computer
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
4(66)
1.3 Adhesives
Use a dentist hook and/or the tweezers to remove old adhesives. Clean the surface with isopropyl alcohol before attaching new adhesives.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
5(66)
Disassembly
When you are going to replace a part being listed in Replacements, the instruction of that section usually begins by directing you to this Disassembly section with a specification of the instructions you have to carry out in order to disassemble the phone as far as needed before returning to Replacements for the actual replacement.
DISASSEMBLY
REASSEMBLY Done
2.1 Overview
The disassembly is done in the following sequence: 1. Battery Cover Assembly (a) 11. Dome Foil Battery (b) 12. Keyboard FPC Assembly 2. Screw Cover Coated 3. Co-Brand Label 4. Antenna Cover Assembly 5. Speakerbox Assembly 6. PBA 7. Card Reader Assembly 8. Sliding Lens Cover 9. Top Rear Inner Panel Assy
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
6(66)
Insert and press the Front Opening Tool down to release the Battery Cover Assembly,
Insert and press the Front Opening Tool down to release the Battery,
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
7(66)
Use the Dentist Hook to remove one of the Screw Cover Coated,
and do the same on the opposite side. THE TWO SCREW COVER COATED MUST BE SCRAPPED, CANNOT BE REUSED!
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
8(66)
Use the Dentist Hook to release and remove the Co-Brand Label. THE CO-BRAND LABEL MUST BE SCRAPPED, CANNOT BE REUSED!
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
9(66)
Use torx bit no. 6 to remove these two 1,6 x 6,1 screws. THE TWO 1,6 X 6,1 SCREWS MUST BE SCRAPPED, CANNOT BE REUSED!
and the second one on the opposite side. THE TWO SCREWS MUST BE SCRAPPED, CANNOT BE REUSED!
Insert the Guitar Pick as shown in picture to unlatch the Antenna Cover Assembly at this side,
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
10(66)
Use a Dentist Hook to release the Antenna Cover Assembly at both ends on this side,
11(66)
NOTE!!! The below information regarding the Antenna Cover Assembly is ONLY for units that are produced before 09w10.
Remove the current gasket and mesh using a scalpel or similar tool. Be careful not to damage the sealing surface on the Antenna Cover.
The protrusion in the plastic shows the placement area for the gasket.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
12(66)
Assemble the new gasket (1203-5255:2) and mesh on the Antenna Cover. Be careful not to cover the holes with the gasket.
Press the gasket hard for 3 seconds to make sure the adhesive is activated.
The gasket should be aligned against the screw boss and metal edge (red).
13(66)
Assemble a grounding gasket also on the opposite side of the Antenna Cover by repeat the above assemble steps.
14(66)
Use the Front Opening Tool to release the Speakerbox Assembly on this side,
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
15(66)
2.1.6
Raise the PBA as far as it goes and disconnect the Keyboard FPC Assembly BtB connector using the Front Opening Tool.
Use the Front Opening Tool to disconnect the LCD FPC connector.
Turn the PBA upside/down and unlock the ZIF connector by opening the lock with the Front Opening Tool.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
16(66)
Use the Flex Film Assembly Tool to pull the FPC out of the ZIF connector.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
17(66)
Use the Front Opening Tool to disconnect this BtB connector which is located on the PBA.
Use the Front Opening Tool to separate the Card Reader Assembly from the PBA.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
18(66)
There are four Plastic Slider Snap as indicated by the arrows in the picture.
Use the Dentist Hook and push all four Plastic Slider Snap down to unsnap them.
Use the Dentist Hook to release them and to have them removed. THE FOUR PLASTIC SLIDER SNAP MUST BE SCRAPPED, CANNOT BE REUSED!
Use the Front Opening Tool to unsnap the Sliding Lens Cover on this side,
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
19(66)
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
20(66)
Use the Dentist Hook to unsnap the Top Rear Inner Panel Assy on this side,
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
21(66)
2.1.10 Keyboard
Use the Flex Film Assembly Tool to separate the Keyboard from the Dome Foil,
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
22(66)
Use the Flex film Assembly Tool to separate the Dome Foil from the Keyboard FPC Assembly,
and then have it removed. THE DOME FOIL MUST BE SCRAPPED, CANNOT BE REUSED!
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
23(66)
Use an ESD Tweezer to separate the Gasket for Keyboard BtB from the Keyboard FPC Assembly. THE GASKET FOR KEYBOARD BTB MUST BE SCRAPPED, CANNOT BE REUSED!
Use the ESD Tweezers to remove the Foil Adhesive Double Side 0.0 mm Adhesive Keyboard Flex. THE FOIL ADHESIVE DOUBLE SIDE 0.0 MM ADHESIVE KEYBOARD FLEX MUST BE SCRAPPED, CANNOT BE REUSED!
Use the Front Opening Tool, or the ESD Tweezers, to unlock the ZIF connector.
Use a Front Opening Tool, or the ESD Tweezers, to release the Keyboard FPC Assembly from the Frame Assy.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
24(66)
Pull the Keyboard FPC Assembly, in the direction of the arrow, to disconnect the ZIF connector.
Use the Flex Film Assembly Tool to release the Keyboard FPC Assembly.
Remove the Keyboard FPC Assembly. THE KEYBOARD FPC ASSEMBLY MUST BE SCRAPPED, CANNOT BE REUSED!
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
25(66)
Replacements
Search for the part to be replaced on the Contents page and go to that instruction to be found in this Replacements section. The instruction usually begins by directing you to the Disassembly section with a specification of the instructions you have to carry out in order to disassemble the phone as far as needed before the actual replacement. Go back to this Replacements section and carry out the instruction. The instruction usually ends by directing you to the Reassembly section with a specification of the instructions you have to carry out in order to reassemble the phone.
DISASSEMBLY
REASSEMBLY Done
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
26(66)
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
27(66)
3.10 Keyboard
Follow the 2.1.3 & 2.1.10 Disassembly instructions! Prepare the new Keyboard. Follow the 4.1.3 & 4.1.10 Reassembly instructions!
28(66)
29(66)
INSTALLATION
Position the new Top Front Outer Panel Assy so that it fits perfectly in the cavity of the Frame Assy and then press with your fingers to have it securely attached.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
30(66)
INSTALLATION
Position the new Carrier Top Front Inner Panel Assy so that it fits perfectly in the cavity of the Frame Assy and then press with your fingers to have it securely attached. Follow the 4.1.4 4.1.5 & 4.1.7 - 4.1.12 Reassembly instructions!
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
31(66)
INSTALLATION
Use the tweezers to position the new Ear Speaker in the Frame Assy and then press with the tweezers, without touching the contacts, to have it securely attached. Follow the 4.1.4 4.1.5 & 4.1.7 - 4.1.12 Reassembly instructions!
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
32(66)
Insert the Front Open Tool between the two FPC parts,
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
33(66)
THE 5MP CAMERA IS ATTACHED WITH GLUE! Insert the Front Opening Tool (1) underneath the 5MP Camera to raise it up (2).
Release and raise the FPC part (1) to make room for the removal of the 5MP Camera. Gently pull (2), using the Flex Film Assembly Tool, to have the 5MP Camera released and removed.
5MP Camera!
INSTALLATION
The Top Rear Inner Panel Assy should now like this.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
34(66)
Optional Instruction In case the Cushion for the QCIF VGA Camera needs to be exchanged, that can be done at this stage: Remove the old Cushion. Insert a new Cushion as shown in picture.
5MP Camera continued Insert the new 5MP Cameras BtB connector underneath the FPC (1) and slide it gently until the connector appears as shown in picture (2). Gently press (3) the 5MP Camera to the bottom of the Top Rear Inner Panel Assy.
Bend the metal holder back to its original position to secure the position of the 5MP Camera.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
35(66)
and attach the loose FPC part on top of the BtB connector. Follow the 4.1.4 4.1.5 & 4.1.7 - 4.1.12 Reassembly instructions!!
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
36(66)
REMOVAL
Follow the 2.1.1 2.1.6 & 2.1.8 2.1.9 Disassembly instructions! Turn the Top Rear Inner Panel Assy upside/down.
Insert the Camera Tool into the Camera Socket (1) as far as it goes in order to release the Qcif VGA Camera from the Camera Socket. Remove the Camera Tool (2) and remove the Camera by lifting straight up (3) using your fingers or the tweezers.
INSTALLATION
Place the Camera into the Socket so that the Cameras guiding peg (1) coincides with the cavity (2) of the Socket. Press with your finger, without touching the lens, and make sure that the Camera has reached the bottom of the Socket.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
37(66)
INSTALLATION
Position the new Shield Can Lid BB 1over the Shield Can Fence and press gently with your fingers until it is properly attached on all sides.
Two kinds of new conductive gaskets have to be attached to the Shield Can Lid BB 1as shown in this picture: two Conductive Gaskets at locations 1 one Conductive Gasket, Grey at location 2 Follow the 4.1.6 4.1.12 Reassembly instructions!
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
38(66)
INSTALLATION
Position the new Shield Can Lid BB 2 over the Shield Can Fence and press gently with your fingers until it is properly attached on all sides. Follow the 4.1.7 4.1.12 Reassembly instructions!
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
39(66)
INSTALLATION
Position the MComp Sheet Metal and snap it onto the Shield Can Lid using the four hooks. Follow the 4.1.6 4.1.12 Reassembly instructions!
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
40(66)
3.24 BT Antenna
REMOVAL
Follow the 2.1.1 2.1.6 Disassembly instructions! Use the Dentist Hook to remove the BT Antenna.
INSTALLATION
Position the new BT Antenna carefully and then attach it to the Frame Assy. Follow the 4.1.7 4.1.12 Reassembly instructions!
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
41(66)
INSTALLATION
Use the tweezers to position and attach the new Side Keys to the hooks at both ends. Follow the 4.1.7 4.1.12 Reassembly instructions!
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
42(66)
and here.
Remove the MComp Spring Metal pogo spring by pressing with the tweezers from the inside of the Frame Assy.
INSTALLATION
Insert new MComp Spring Metal pogo spring from the outside of the Frame Assy and push with the tweezers as far as it goes. Follow the 4.1.4 4.1.5 & 4.1.7 4.1.12 Reassembly instructions!
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
43(66)
If there are traces of liquid intrusion on any Liquid Intrusion Indicator, abort further repair actions and handle the phone in accordance with your local directives. Follow the 4.1.7 4.1.12 Reassembly instructions!
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
44(66)
3.28 Display & Touch Sensor FPC Assy & Light diffusion film
REMOVAL
Follow the 2.1.1 2.1.12 Disassembly instructions! Press down the Frame Assy at opposite corners (1) in order to release the Display from the Frame Assy (2).
Use tweezers to remove the Touch Sensor FPC Assy. THE TOUCH SENSOR FPC ASSY CANNOT BE REUSED!
Use tweezers to remove the Light diffusion film. THE LIGHT DIFFUSION FILM CANNOT BE REUSED!
45(66)
Display 2.0 TFT & Touch Sensor FPC Assy & Light diffusion film continued
INSTALLATION
Use blunt pair of tweezers to position the new Light diffusion film.
Use ESD tweezers to position the new Touch Sensor FPC Assy.
Turn the Frame around and use the Guitar Pick to fold down the four metal wings on the new Display
46(66)
Install the LCD pressure tool insert into the pressure tool.
Display 2.0 TFT & Touch Sensor FPC Assy & Light diffusion film continued
Use the Pressure Tool to press with 100 N the Keyboard for at least 5 seconds. Follow the 4.1.1 4.1.12 Reassembly instructions!
47(66)
Check that the proper label format is loaded in the Zebra printer Write a new label by using the program Label make and check that the printing is OK Take the new label and place it onto the frame as in the adjacent picture ONE LABEL ONLY IS ALLOWED! Follow the 4.1.12 Reassembly instructions!
48(66)
Reassembly
After replacing a part being listed in Replacements, the instruction of that section usually ends by directing you to this Reassembly section with a specification of the instructions you have to carry out in order to reassemble the phone.
DISASSEMBLY
REASSEMBLY Done
4.1 Overview
The reassembly is done in the following sequence: 1. Keyboard FPC Assembly 11. Screw Cover Coated 2. Dome Foil 12. Battery (a) 3. Keyboard Battery Cover Assembly (b) 4. Top Rear Inner Panel Assy 5. Sliding Lens Cover 6. Card Reader Assembly 7. PBA 8. Speakerbox Assembly 9. Antenna Cover Assembly
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
49(66)
Place the Keyboard FPC Assembly so that it fits in the cavity (indicated by arrows) of the Frame Assy and press to attach it.
Use the Flex Film Assembly Tool to connect the ZIF connector of the Keyboard FPC Assembly (1). Lock the ZIF connector (2).
Use the ESD tweezers to attach a new Foil Adhesive Double Side 0.0 mm Adhesive Keyboard Flex.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
50(66)
Use the ESD tweezers to attach a new Gasket for Keyboard BtB to the Keyboard FPC Assembly.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
51(66)
Attach a new Dome Foil while using the holes indicated by the arrows as guides to the corresponding holes on the Keyboard FPC Assembly.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
52(66)
4.1.3 Keyboard
Place the Keyboard on top of the Dome Foil so that the lower part of the Keyboard touches the border of the Frame Assy.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
53(66)
Position the Top Rear Inner Panel Assy to the Frame Assy,
and snap the Top Rear Inner Panel Assy to the Frame Assy.
Press like this to secure that both sides are properly snapped.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
54(66)
THE SLIDING LENS COVER MUST BE FULLY OPENED! Get four new Plastic Slider Snap and attach them to the Frame Assy, two on each side.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
55(66)
THE SHIELD CAN LID HAS GUIDING PINS! Position the Card Reader Assembly,
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
56(66)
4.1.7
Turn the PBA upside/down and insert the FPC into the ZIF connector using the Flex Film Assembly Tool as shown in picture.
Raise the PBA and connect the LCD FPC BtB connector by carefully pressing with your finger,
and then connect the Keyboard FPC Assembly BtB connector to the PBA in the same way.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
57(66)
and place it like this. MAKE SURE THE SIDE SWITCHES ARE POSITIONED CORRECTLY!
Press on the Card Reader Assembly until the PBA is properly latched to the Frame Assy.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
58(66)
Press carefully with your finger to connect the BtB connector of the Speakerbox Assembly FPC to the PBA.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
59(66)
and use the Front Opening Tool to press and snap the Antenna Cover Assembly onto the Frame Assy on this side,
Press by using the Front Open Tool to make this part of the Antenna Cover Assembly snap to the Frame Assy, on both sides.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
60(66)
Use the PH00 bit to tighten one new Flat Head Screw on each side of the phone with10 Ncm torque.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
61(66)
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
62(66)
Use the Flex Film Assembly Tool to attach one new Coated Screw Cover on each side of the phone.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
63(66)
64(66)
Insert the Battery (1) and press down (2) to secure its position.
Place the Battery Cover Assembly like this (1) and press down (2) to secure its position.
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
65(66)
Revision History
Date 2008-06-05 2008-07-04 2008-11-11 2008-11-12 2009-01-09 2009-01-23 2009-03-05 2009-03-23 Changes / Comments First release Updated With C902c Chapter 3.15 and 3.29 added Document updated Chapter 3.27 Liquid Intrusion Indicator updated Updated chapter 3.28 Display & Touch Sensor FPC Assy & Light diffusion film Updated Chapter 3.20 Qcif VGA Camera & Camera Gasket Updated Chapter 2.1.4 Antenna Cover Assembly
Rev. 1 2 3 4 5 6 7 8
1212-7760 State: Preliminary 8.1 Company Internal Sony Ericsson Mobile Communications AB
66(66)