Beruflich Dokumente
Kultur Dokumente
com
LG LCD Inc.
Product Specification
( (
Title
BUYER NAME MODEL NAME
SIGNATURE
DATE
SIGNATURE
DATE
APPROVED BY S. H. Kang REVIEWED BY S. C. YUN B. H. KOO PREPARED BY H. S. SONG S. J. LEE Please return 1 copy for our confirmation with your signature and comments. Product Engineering Dept. LG LCD Inc.
LG LCD Inc.
Product Specification
TABLE of CONTENTS
NO.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. -
ITEM
COVER TABLE of CONTENTS RECORD of REVISION GENERAL DESCRIPTION MAXIMUM RATINGS ELECTRICAL SPECIFICATIONS OPTICAL SPECIFICATIONS INTERFACE CONNECTIONS SIGNAL TIMING SPECIFICATIONS SIGNAL TIMING WAVE FORMS COLOR INPUT DATA REFERENCE POWER SEQUENCE MECHANICAL CHARACTERISTICS HANDLING PRECAUTIONS INTERNATIONAL STANDARDS APPENDIX
Page
1/19 2/19 3/19 4/19 5/19 5/19 6/19 7/19 9/19 10/19 12/19 13/19 14/19 16/19 17/19 18/19
Version 1.4
08 / Jul. / 1999
Page 2/19
LG LCD Inc.
Product Specification
Record of Revision
DATE AND VERSION 22 / Jan. / 1999 & Ver. 1.0 12 / Feb. / 1999 & Ver. 1.1 1. 2. 375 3. 12 / Apr. / 1999 & Ver. 1.2 DESCRIPTION Initial Release To Change Model Name (All Page) To change Power supply current (5 Page) : Typ Max Typ Max 410 570 [mA] 510 LP141X4-C1 LP141XA-A1
To add International Standards (17 Page) : Min. Rx Ry Gx Gy Bx By Wy Wy Typ Max Min. Typ Max
1. To Changed Color Coordinates (6 Page) 0.542 0.572 0.602 0.320 0.350 0.380 0.267 0.297 0.327 0.519 0.549 0.579 0.122 0.152 0.182 0.110 0.140 0.170 0.271 0.301 0.331 0.312 0.342 0.372 0.548 0.578 0.608 0.317 0.347 0.377 0.278 0.308 0.338 0.507 0.537 0.567 0.121 0.151 0.181 0.101 0.131 0.161 0.281 0.311 0.341 0.311 0.341 0.371
28 / May / 1999 & Ver. 1.3 08 / Jul. / 1999 & Ver. 1.4
1.
To change Power Sequence (13 Page) Lamp On Time : 200[mS] min. 50[mS] min.
1. Update Mechanical Drawing(14, 15 Page) 2. Change Power Sequence (13 Page) VDD off time : 20 [mS] max. 40 [mS] max.
Version 1.4
08 / Jul. / 1999
Page 3/19
LG LCD Inc.
Product Specification
1. General Description
The LG LCD Inc. model LP141XA-A1 LCD is a Color Active Matrix Liquid Crystal Display with an integral Cold Cathode Fluorescent Tube(CCFT) back light system. The matrix employs a - Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally white mode. This TFTLCD has a 14.1 inch diagonally measured active display area with XGA resolution(768 vertical by 1024 horizontal pixel array). Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes. The LP141XA-A1 Gray scale or the brightness of the sub-pixel color is determined with a 6-bit gray scale signal for each dot, thus, presenting a pallet of more than 262,144 colors. LCD is intended to support applications where low power consumption, weight and In combination with the vertical thickness are critical factors and graphic displays are important. office automation products such as portable computers.
arrangement of the sub-pixels, the LP141XA-A1 characteristics provide an excellent flat panel display for
Power Supply
VDD GND Rin0 Rin0 + Rin1 Rin1 + Rin2 Rin2 + CLK CLK +
User Connector(CN1)
Row Driver
Control Signal
Column Driver
CN2
Version 1.4
08 / Jul. / 1999
Page 4/19
LG LCD Inc.
Product Specification
2. Maximum Ratings
The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit. Table 1 ABSOLUTE MAXIMUM RATINGS Parameter Power Input Voltage Logic Input Voltage Operating Temperature symbol Min. VDD VL/H TOP Values Max. Units Vdc Vdc Notes at 25 at 25 1 1
TST Storage Temperature Note: 1. The Relative Humidity must not exceed 80% non-condensing at temperatures of 40 or less. At temperatures greater than 40, the wet bulb temperature must not exceed 39. At low temperature the brightness of CCFL drop and the life time of CCFL become to be short. 2. Under no condition should the unit be exposed to corrosive chemicals.
0 -0.3 0 -20
3. Electrical Specifications
The LP141XA-A1 requires two power inputs. One is employed to power the LCD electronics and to derive the voltages to drive the TFT array and liquid crystal. The second input which powers the backlight CCFT, is typically generated by an inverter. The inverter is an external unit to the LCD. Table 2 ELECTRICAL CHARACTERISTICS: Parameter MODULE: Power Supply Input Voltage Power Supply Input Current Ripple/Noise Differential input voltage - High for receiver threshold BACKLIGHT Backlight Input voltage Backlight Current Established starting Voltage Operating Frequency FBL 40 60 VBL IBL 680 3.0 725 5.0 850 6.0 1170 1450 80 VRMS mA VRMS VRMS KHz 252, 5 0 4 Low VDD IDD VIH VIL 3.0 -100 3.3 410 60 3.6 570 100 100 Vdc mA mV mV mV 3 1,2 Symbol Min. Values Typ. Max. Units Notes
Hours 10,000 @ IBL= 6mA CCFL Life Time Notes 1. The current draw and power consumption specified is for 3.3 Vdc at 25. 2.Typical value is measured when displaying black screen. Maximum power situation measured with alternating vertical lines by 2 black_white pattern. For more information see Appendix A-1. 3. LVDS common mode voltage, VCM=1.2V 4. The backlight power consumption shown above does not include loss of external inverter. 5. The voltage of inverter is more than the established starting voltage.
Version 1.4
08 / Jul. / 1999
Page 5/19
LG LCD Inc.
Product Specification
4. Optical Specifications
Optical characteristics are determined after the unit has been ON and stable for approximately 30 minutes in a dark environment at 25. The values specified are at an approximate distance 50cm from the LCD surface at a viewing angle of and equal to 0. Appendix A presents additional information concerning the specified characteristics. Table 3 OPTICAL CHARACTERISTICS Parameter Contrast Ratio White Surface Brightness Brightness Variation Response Time Rise Time Decay Time RED GREEN BLUE WHITE Viewing Angle (CR>10:1) x axis, right ( =0 ) x axis, left( =180 ) y axis, up( =90 ) SBV TrR TrD x y x y x y x y 0.548 0.317 0.278 0.507 0.121 0.101 0.281 0.311 45 45 10 20 30 0.578 0.347 0.308 0.537 0.151 0.131 0.311 0.341 1.80 40 50 0.608 0.377 0.338 0.567 0.181 0.161 0.341 0.371 msec msec degree degree degree 6 6 6 6 6 6 6 6 5 5 5 3 Symbol CR SBWH Values Min. 150 100 Typ. 250 120 Max. Units cd/m
2
Notes 1 2
IBL=6.0mA
Color Coordinates
y axis, down ( =270 ) 30 degree 5 Notes 1. Contrast Ratio (CR) is defined mathematically as: (Surface Brightness with all white pixels) (Surface Brightness with all black pixels) 2. Surface brightness is 5 spot average of measurement across the LCD surface 50cm from the surface with all pixels displaying white. For more information see Appendix A-2. 3. The variation in surface brightness, SBV is determined by measuring BON at each test position 1 through 13, and then dividing the maximum BON by the minimum BON. For more information see Appendix A-3. Maximum (BON1, BON2, ....BON13) Minimum (BON1, BON2, ....BON13) 4. Response time is the time required for the display to transition from white to black (Rise Time, TrR) and from black to white (Decay Time, TrD). For additional information see Appendix A-4. 5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see Appendix A-5. 6. Color Coordinates can be changed according to color filter. (In case of changing color filter, we will tell our customer.)
Version 1.4
08 / Jul. / 1999
Page 6/19
LG LCD Inc.
Product Specification
5. Interface Connections
This LCD employs two interface connections, a 20 pin connector is used for the module electronics and a two pin connector is used for the integral backlight system. The electronics interface connector is a model FI-SEB-20P-HF or equivalent. The pin configuration for the connector is shown in the table below.
Table 4 MODULE CONNECTOR PIN CONFIGURATION (CN1) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol VDD VDD GND GND Rin0 Rin0 + GND Rin1 Rin1 + GND Rin2 Rin2 + GND CLK CLK + GND NC NC GND GND Description Power supply, 3.3V Power supply, 3.3V Ground Ground Receiver signal (-) Receiver signal (+) Ground Receiver signal (-) Receiver signal (+) Ground Receiver signal (-) Receiver signal (+) Ground Clock signal (-) Clock signal (+) Ground Reserved Reserved Ground Ground Pin 1 Pin 20 User Connector Notes
Notes: 1. All GND(ground) pins should be connected together and to GND which should also be connected to the LCDs metal frame. 2. All VDD(power input) pins should be connected together.
Version 1.4
08 / Jul. / 1999
Page 7/19
LG LCD Inc.
Product Specification Interface Connections (contd)
The backlight interface connector is a model BHSR-02VS-1, manufactured by JST. The mating connector part number is SM02B-BHSS-1-TB or equivalent. The pin configuration for the connector is shown in the table below.
Table 5 BACKLIGHT CONNECTOR PIN CONFIGURATION (CN2) Pin Symbol Description Notes 1 HV Lamp power input 1 2 LV Ground 2 Notes: 1. The input power terminal is white 2. The ground terminal is black.
LG LCD Inc.
Product Specification
ITEM
LVDS Timing (Note 1)
SIGNAL
Clock
ITEM
Frequency Period
LVDS Low to High time LVDS High to Low time Set up time, serial bits
Transition time Transition time Receiver Input Strobe Bit 0 Receiver Input Strobe Bit 1 Receiver Input Strobe Bit 2 Receiver Input Strobe Bit 3 Receiver Input Strobe Bit 4 Receiver Input Strobe Bit 5 Receiver Input Strobe Bit 6
DENA
Low width Horizontal Front Porch Horizontal Back Porch Vertical Front Porch Vertical Back Porch
HD
tCLKIN tCLKIN
Hz
WHL
VD
f t
tH tH
tWVL
Note : 1. Measurement is made at panel side flex connector with dummy 100 ohm termination. 2. Polarities of HD and VD are negative. 3. DENA should always be positive polarity. 4. CLKIN should appear during all invalid period. HD should appear during invalid period of the frame cycle.
Version 1.4
08 / Jul. / 1999
Page 9/19
LG LCD Inc.
Product Specification
Vdiff = 0 V
Link 0
P0C2 P0C1 G0 R5
P0C7 P0C6 R4 R3
P0C2
P0C1
P0C7
Link 1
P1C2 P1C1 B1 B0
P1C7 P1C6 G5 G4
P1C2
P1C1
P1C7
Link 2
P2C7 P2C6 HD B5
P2C2
P2C1
P2C7
tdp 0 tdp 1 tdp 2 tdp 3 tdp 4 tdp 5 tdp 6 V IN V IN + Typical of all timing instances
Version 1.4
08 / Jul. / 1999
Page 10/19
LG LCD Inc.
Product Specification
CLK First Data DATA (R,G,B) DENA Invalid Data 1 2 3 Last Data 1023 Invalid Data
Line data
767 768
HD
VD
Version 1.4
08 / Jul. / 1999
Page 11/19
LG LCD Inc.
Product Specification
Green(63) Black 0
Version 1.4
08 / Jul. / 1999
Page 12/19
LG LCD Inc.
Product Specification
9. Power Sequence
1 Sec min
VDD
0V
10%
90%
90% 10%
10mS max
20mS max
40mS max
Signals
0V
10% 10%
50mS min
200mS
Lamp ON
0V
10% 10%
Notes : 1. Please avoid floating state of interface signal at invalid period. 2. When the interface signal is invalid, be sure to pull down the power supply for LCD VDD to 0V.
Version 1.4
08 / Jul. / 1999
Page 13/19
LG LCD Inc.
Product Specification
LG LCD Inc.
Product Specification
* Mounting Screw depth : 2.0[mm] Min. 2.3[mm] Max. * Torque : 1.3 ~ 1.5 [kgf cm]
LG LCD Inc.
Product Specification
Please pay attention to the followings when you use this TFT/LCD module with Back-light unit. 11.1.MOUNTING PREACAUTION 1)You must mount Module using mounting holes arranged on metal frame sides. Be sure to turn off the power when connecting or disconnecting the circuit. 2) Note that the polarizers are easily damaged. Pay attention not to scratch or press this surface with any hard object. 3) When the LCD surface become dirty, please wipe it off with a soft material. (ie. cotton ball) 4) Protect the module from the ESD as it may damage the electronic circuit (C-MOS). Make certain that treatment persons body are grounded through wrist bend. 5) Do not disassemble the module and be careful not to incur a mechanical shock that might occur during installation. It may cause permanent damage. 6) Do not leave the module in high temperatures, Particularly in areas of high humidity for a long time. 7) The module not be expose to the direct sunlight. 8) Avoid contact with water as it may a short circuit within the module. 11.2 OPERATING PRECAUTION 1) The spike noise causes the mis-operation of circuits. Be lower the spike noise as follows : VDD=200mV, V1=200mV( Over and under shoot voltage.) 2) Response time depends on the temperature. (In lower temperature, it becomes longer.) 3) Brightness depends on the temperature. (In lower temperature, it becomes lower.) And in lower temperature, response time (Required time that brightness is stable after turn on)becomes longer. 4) Be careful for condensation at suddern temperature change. Condensation make damage to polarizer or electrical contact part. And after fading condensation, smear or spot will occur. 5) When fixed pattern are displayed at long times, remnant image is likely to occur. 6) Module has high frequency circuit. If you need to shield the electromagnetic noise. Please do in yours. 7) When Back-light unit is operating, it sounds. If you need to shield the noise, please do in yours. 11.3 ELECTROSTATIC DISCHARGE CONTROL Since module is composed with electronic circuit, it is not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through list band etc.. And dont touch I/F pin directly. 11.4 PRECAUTION FOR STRONG LIGHT EXPOSURE. Strong light exposure causes degradation of polarizer and color filter. 11.5 STORAGE When storing module as spares for long time, the following precautions are necessary. 1) Store them in a dark place : do not expose then to sunlight or fluorescent light. Keep the temperature between 5 and 35 at normal humidity. 2) The polarizer surface should not come in contact with any other object. It is recommended that they be stored in the container in which they were shipped.
Version 1.4
08 / Jul. / 1999
Page 16/19
LG LCD Inc.
Product Specification 11.6 HANDLING PRECAUTIONS FOR PROTECTION FILM
1) When the protection film is pealed off, static electricity is generated between the film and the polarizer. This film should be pealed off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition. etc. 2) The protection film is attached the polarizer with a small amount of glue. If some stress is applied to rub the protection film against the polarizer during the time you peal off the film, the glue is apt to remain more on the polarizer. So please carefully peal off the protection film without rubbing it against the polarizer. 3) When the module with protection film attached is stored for long time, sometimes there remains a very small amount of glue still on the polarizer after the protaction film is pealed off. Please refrain from storing the module at the high temperature and high humidity for glue is apt to remain in these condition. 4) The glue may be taken for the modules failure, but you can remove the glue easily. When the glue remains on the polarizer surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with Normal-hexane.
Version 1.4
08 / Jul. / 1999
Page 17/19
LG LCD Inc.
Product Specification
. APPENDIX
A-1 BLACK Pattern & Alternating Vertical Lines by 2 Black_White Pattern
R G B R G B
B B
R R
G G
B B
R R
2 1 4
192 384
576
< Measuring Point > A-3. 13 SPOT LUMINANCE VARIATION MEASUREMENT LOCATIONS
10mm
10mm
256
10mm
512
7
768
8
6
2
192
10
384 576
4
10mm
11
12
13
(LINES)
Version 1.4
08 / Jul. / 1999
Page 18/19
LG LCD Inc.
Product Specification A-4 RESPONSE TIME
The response time is defined as the following figure and shall be measured by switching the input signal for black and white.
TrR
%
100 90
TrD
Optical Response
10 0
white black
white
= 0 z
xl
xr
z'
yd
= 270 (6:00)
Version 1.4
08 / Jul. / 1999
Page 19/19