Beruflich Dokumente
Kultur Dokumente
0 0 0 1 1 0 0 1
N N N Y Y N N Y
N N N Y Y N N Y
1 0 1 2 2
N N Y Y Y
N N Y Y Y
1 0 0 1 2 0 2 4 2 4 1 2
N N N N Y Y Y Y Y N N Y
N N N N Y Y Y N N N N Y
2 0 0 1 2 0 2 4 2 4 2
N N N N Y Y Y N Y N N
N N N N Y Y Y N N N N
2 1 2 2 2 1 1 2 2 2
N N Y Y Y N N Y Y Y
N N Y N N N N Y N N
3 0 0 2 4 0 3 4 3 4 3 0
N N N N Y Y Y N Y N N N
N N N N Y Y Y N N N N N
3 2 0 4 4 2 4 4 4 4 3 4
N N N N Y Y Y N Y N N N
N N N N Y Y Y N N N N N
ARC Resistant Switchgear Type 1 or 2 (for clearing times of <.05 with a perspective fault current not to exceed the Arc resistant rating of the equipment) CB operation with enclosure doors closed Insertion or removal (racking) of CBs from cubicles, doors open or closed Insertion or removal of CBs from cubicles with door open Work on control circuits with energized electrical conductors and circuit parts 120 V or below, exposed Insertion or removal (racking) of ground and test device with door closed Insertion or removal (racking) of voltage transformers on or off the bus door closed Other Equipment 1kV Through 38 kV Metal-enclosed interupter switch gear, fused or unfused Switch operation of arc-resistant-type construction, tested in accordance with IEEE C37.20.7, doors closed only Switch operation, doors closed Work on energized electrical conductors and circuit parts, including voltage testing Removal of bolted covers (to expose bare, energized electrical conductors and circuit parts) Opening hinged covers (to expose bare, energized electrical conductors and circuit parts) Outdoor disconnect switch operation (hook stick operated) Outdoor disconnect switch operation (gang-operated, from grade) Insulated cable examination, in man hole or other confined spaces Insulated cable examination, in open area General Notes (applicable to the entire table): (a) Rubber insulating gloves rated for the maximum line-to-line voltage upon which work will be done. (b) Insulated and insulating hand tools are tools rated and tested for the maximum line-to-line voltage upon which work will be done, and are manufactured and tested in accordance with ASTM zg 1505. Standard Specification for Insulated Hand Tools. (c) Y = yes (required), N = no (not required) (d) For systems rated less than 1000 volts, the fault currents and upstream protective device clearing times are based on an 18 in. working distance. (e) For systems rated 1 kV and greater, the Hazard/Risk Categories are based on a 36 in. working distance. (f) For equipment protected by upstream current limiting fuses with arcing fault current in their current limiting range (1/2 cycle fault clearing time or less), the hazard/risk category required may be reduced by one number. Specific Notes (as referenced in the table): 1. Maximum of 25 kA short circuit current available ; maximum of 0.03 sec (2 cycle) fault clearing time. 2. Maximum of 65 kA short circuit current available ; maximum of 0.33 sec (2 cycle) fault clearing time. 3. Maximum of 42 kA short circuit current available ; maximum of 0.33 sec (20 cycle) fault clearing time. 4. Maximum of 25 kA short circuit current available ; maximum of up to 0.5 sec (30 cycle) fault clearing time. 0 2 4 4 3 3 2 4 2 N N Y N N Y Y Y Y N N Y N N Y N N N 0 0 4 2 0 0 N N N Y N N N N N Y N N
The assumed short maximum circuit current capacities and maximum fault clearing times for various tasks are listed int eh notes to table (130.7(C)(9). For Tasks not listed, or For Power systems with greater than the assumed maximum short circuit current capacity or With longer than the assumed maximum fault clearing times - AN ARC FLASH ANALYSIS SHALL BE REQUIRED IN ACCORDANCE WITH 130.3
CATEGORY
0
CATEGORY
1
Ending at 4 CAL/cm
What Personal Protection Equipment (PPE) You Shall Wear: (X) Cotton Undergarments (X) ARC Rated Long Sleeved Shirt (or FR Coveralls) (X) ARC Rated Long Pants (or FR Coveralls) (X) Hard Hat with ARC Rated Face Shield (X) Hearing Protection (Inserts) (X) Safety Glasses or Goggles (X) Leather Gloves (as needed) or Insulating Gloves w/Protectors. (X) Leather Shoes (as needed)
CATEGORY
2
Ending at 8 CAL/cm
What Personal Protection Equipment (PPE) You Shall Wear: (X) Cotton Undergarments (X) Short Sleeved T Shirt (Natural Fiber) (X) ARC Rated (12cal) Arc Flash Hood or Hard Hat with Arc Rated Face Shield w/Sock Balaclava with Coveralls or Jacket & Bibs or 50 Coat with Leggings (X) Safety Glasses or Goggles (X) Hearing Protection (X) Arc Rated Leather Gloves or Insulating Gloves w/Protectors (X) Leather Shoes
CATEGORY
3
Ending at 25 CAL/cm2
What Personal Protection Equipment (PPE) You Shall Wear: (X) Cotton Undergarments (X) Short Sleeved T Shirt (Natural Fiber) (X) ARC Rated (25cal) Arc Flash Hood with Coveralls or Jacket & Bibs or 50 Coat with Leggings. (X) Hard Hat (X) Hearing Protection (X) Safety Glasses or Goggles (X) Arc Rated Leather Gloves or Insulating Gloves w/Protectors (X) Leather Shoes
CATEGORY
Ending at 40 CAL/cm
What Personal Protection Equipment (PPE) You Shall Wear: (X) Cotton Undergarments (X) Short Sleeved T Shirt (Natural Fiber) (X) Arc Rated (40cal) Arc Flash Hood with Coveralls or Jacket & Bibs or 50 Coat with Leggings (X) Hard Hat (X) Hearing Protection (X) Safety Glasses or Goggles (X) Arc Rated Leather Gloves or Insulating Gloves w/Protectors (X) Leather Shoes
Always wear voltage rated rubber glove liners when working above 50 volts in all categories!
Class 00
2,500
500
750
Class 0
5,000
1,000
1,500
Class 1
10,000
7,500
11,250
Class 2
20,000
17,000
25,500
Class 3
30,000
26,500
39,750
Class 4
40,000
36,000
54,000
29CFR part 1910 - Occupational Safety and Health Standards ASTM D 120-08 - Rubber Insulating Gloves ASTM F496-08 - In-Services Care of Insulating Gloves and Sleeves ASTM F696-06 - Leather Protectors for Rubber Insulating Gloves and Mittens ASTM F1236-96 - Visual Inspection of Electrical Protective Rubber Products
NFPA Standards
National Electric Safety Code - Utilities NFPA 70E - Electrical Safety in the Workplace - General Workplaces