Beruflich Dokumente
Kultur Dokumente
MADE IN USA
T.O.C.
MAGAZINES STOCKS SLING SYSTEm GRIPS HANDGUARDS SIGHTS AND ACCESSORIES SHOTGUN LIFESTYLE/GEAR mAGPUL DYNAmICS 4 28 46 52 64 70 76 82 96
Many of the products in this catalog are subject to the Arms Export Control Act (22 U.S.C. 7728) and the International Trafc in Arms Regulations (22 C.F.R. Parts 120-130). A prior authorization or license from the U.S. State Department Directorate of Defense Trade Controls is required for the export, re-export or re-transfer of those products to any foreign person whether in the United States or abroad, either in their original form or after being incorporated into other end items.
2013 Magpul Industries Corporation. All Rights Reserved. Prices subject to change without notice. MAGPUL holds a Trademark on all of its product names and logos. The following are trademarks of Magpul Industries Corporation, registered in the U.S. and other countries: AFG, American Manufacturing Logo, ASAP, B.A.D. LEVER, CTR, MAGPUL, Stylized Magpul Logo, Magpul Inner Logo, Maglink, MBUS, MIAD, MOE, MVG, PMAG, PRS, RSA, RVG, SGA, SPEEDPLATE, Tenth Anniversary Logo, UBR, UNFAIR ADVANTAGE. MELONITE is a registered trademark of Durferrit GmbH. REMINGTON is a registered trademark of RA Brands, LLC. FN and SCAR are trademarks of FN Herstal S.A. HK is a trademark of Heckler & Koch GmbH. MASH HOOK is a trademark of ITW Waterbury Buckle. GLOCK is a registered trademark of Glock GmbH. SUREFIRE and SCOUT LIGHT are trademarks of Surere, LLC.
MAGAZINES
MAGPUL
MADE IN USA
THE MAGAZINE. WE ASK A LOt FROm tHIS LIttLE BOX, wItHOUt wHICH OUR FIREARmS BECOmE FAR LESS USEFUL. THIS SImPLE FEEDING DEVICE CAN EASILY BE tAKEN FOR GRANtEDUNtIL It DOESNt wORK.
Our entire line of magazines is designed, manuf ac tured, and tested to exceed anything youre likely to ask of them, using demanding scientific testing procedures that go beyond what others consider requirements, and including over ve years on the battleeld as the most-elded polymer magazine for the M4/M16 family of weapons platforms. A magazine needs to do several things really well. It needs to feed as awlessly as possible, in all compatible platforms under both normal and adverse conditions. It also needs to resist damage due to rough handling, abuse, impacts, and other hazards of extreme use. Balancing those requirements is difcult. Dominating them is Magpul.
The MagLevel round indicator system allows for visual verication of the magazine's loaded round count via a bright orange indicator coil. By incorporating a window on both sides of the magazine, it is easily used by both right and left handed shooters. By using the indicator coil and window, the user gets an indication of remaining rounds until the magazine is empty rather than losing all indicators when the round stack enters the magazine well, as in other visible round count systems.
M AGA ZINES
M AGA ZINES
MAGPUL
DeFaCTO
SAY HELLO TO THE NEW
LIKE ItS PREDECESSORS, tHE PMAG 30 GEN M3 IS A LIGHtwEIGHt 5.56 X 45 NATO / .223 REmINGtON 30-ROUND POLYmER mAGAZINE FOR tHE AR15/M4 PLAtFORm, BUt wItH A NUmBER OF NEw FEAtURES AND ADVANCED CHARACtERIStICS tHAt OPtImIZE ItS DURABILItY, COmPAtIBILItY, AND OVERALL PERFORmANCE FOR tHE mOSt DEmANDING END-USERS. BY COmBINING tHE KNOwLEDGE GAINED FROm YEARS OF HIGH VOLUmE PMAG PRODUCtION, EXtENSIVE RESEARCH AND DEVELOPmENt OF mAtERIALS AND mANUFACtURING PROCESSES, AND INCORPORAtING FEEDBACK FROm A BROAD RANGE OF END-USERS, tHE PMAG 30 GEN M3 PUSHES tHE ENVELOPE OF mAGAZINE PERFORmANCE ONE StEP FURtHER.
The PMAG 30 GEN M3 is a polymer magazine for AR15/M4 compatible firearms with an expanded feature set and compatibility compared to our earlier PMAGs. Advances in material technology and manufacturing processes help to make this the most reliable and durable PMAG to date. Here at Magpul, when we make a product, we have a hard time leaving it alone. We continue to test, to collect feedback from end-users, and to find ways to improve. The original PMAG benefited from these efforts with the MREV improvements in 2009. Since then, weve continued the quest for constant evolution. With millions of magazines in worldwide military service and a self-critical eye in our engineering department, the M3 project started in 2011. Over a full year later, we are finally ready to show our hand. lip impact, spine strength, side impact, cold and hot weather impacts, and crush testing haveallimprovedsignificantlyoverprevious generationsto the point that we think youll find the results impressive, to say the least. Youll also see a new, innovative window material with superior chemical resistance and durability properties. The external geometry of the GEN M3 is slightly different than the previous generation of PMAG. In order to have compatibility with the widest variety of firearms platforms, the frontstoponthemagazinehasbeenrelocated for full compatibility with the HK 416/IAR/ M27 and the SA-80. A new, enhanced overinsertionstophasbeenaddedtotherearspine of the magazine. This new stop is compatible with nearly all magazine well geometries and provides support for rough handling of the loaded firearm as well as allowing extremely aggressive magazine changes with no danger of malfunctions or damage caused by over-insertion. Our increases in material technology and manufacturing have also permitted gains in strength while allowing narrower external dimensions, for greater drop-free compatibility with magazine wells onthetightersideofthetolerancerange. Internal geometry received an update as well. Proven constant curve geometry is combined with a new, low-friction, four-way anti-tilt follower designed to improve on our already excellent adverse conditions functioning, especially in dust or grit environments, thanks to generous clearances. The new follower color is gray, to distinguish it from previous follower generations. There are numerous other improvements and added features. First, the magazine catch area is reinforced both for extra strength and for improved function with a wider range of magazine catch tolerances. In keeping with the quest for compatibility, the bolt catch notch has been expanded to be compatible with the FN SCAR while still showing significant strength and durability gains in this critical area. On the outside, youll notice improved texture on both the front and back spines, as well as slightly modified side ribs to enhance handling characteristics when wet, dirty, or when under stress. The new floor plate design shows significant strength increases over previous designs while being slimmer for easier side-by-side carry and also having features to increase drainage for maritime operations. In the nice to have category, there is a paint pen dot matrix on the bottom sides of each magazine to allow consistent magazine marking that resists wear due to rough handling. This feature makes magazine marking easier and all but eliminates having to re-mark magazines after friction and solvents have worn your original markings. All of this talk of improvements, strength, and durability really means nothing if the magazine doesnt feed, and that is what we are most excited about. Its easy to design and build a plastic brick that fits in a magazine welland much harder to build a true asset to a weapons system that functions flawlessly across a wide spectrum of temperature and condition extremes with various ammunition types, across numerous platforms, extreme cyclic rates, and other variables. The GEN M3 has exceeded even our own high expectations in reliability, compatibility, and endurance testing. Tests like 6,000 rounds through a single magazine, dirt/ sand/grit testing, drop, crush, and impact testing, temperature extreme testing, extensive field testingall per applicable military standards, and all demonstrating the performance we demand from the next generation to wear the PMAG name.
MADE IN USA
Polymer technology is constantly advancing, and we are continually pushing the boundaries of what is possible with new materials, manufacturing methods, and quality control. What weve arrived at with theGENM3isamagazinethatissignificantly stronger in all areas. Performance in feed
M AGA ZINES
M AGA ZINES
MAGPUL
MADE IN USA
The next-generation PMAG 30 GEN M3 is a 30-round 5.56x45 NATO (.223 Remington) polymer magazine for AR15/ M4 compatible weapons. Modied internal and external geometry also permits operation with a wide range of non Coltspec platforms such as the HK 416 and MR556A1, M27 IAR, British SA-80, FN SCAR MK 16/16S, and others. A redesigned bolt catch notch in the rear of the magazine provides increased bolt catch clearance, while an over-travel stop on the spine helps ensure the magazine will not over-insert on compatible weapons. Similar to the MOE PMAG, the GEN M3 features a long-life stainless steel spring, four-way anti-tilt follower and constant-curve internal geometry
for reliable feeding, and simple tool-less disassembly to ease cleaning. In addition, an included pop-off Impact/Dust Cover can optionally be used to minimize debris intrusion and protect against potential damage during storage and transit. Low prole ribs and new aggressive front and rear texture gives positive control of the GEN M3 in all environments, and a paint pen dot matrix has been added to the bottom panel of the body to allow easy marking by the end user for identication. The new, easy to disassemble ared oorplate aids extraction and handling of the magazine while providing improved drop protection, but is slightly slimmer than before for better compatibility with tight double and triple magazine pouches.
The PMAG 30 GEN M3 Window is a light weight 5.56 x 45 NATO (.223 Remington) 30 -round polymer magazine for the AR15/M4 compatible weapons, designed to allow approximate verication of loaded round count.
THEORY BASED PRODUCT
Maintaining the same improved feature set and performance characteristics as the standard version, the PMAG 30 GEN M3 Maglevel Window features dualside transparent windows and bright orange indicator coil to allow rapid visual identication of approximate number of rounds remaining in the magazine.
M AGA ZINES
M AGA ZINES
MAGPUL
MADE IN USA
The PMAG 20 GEN M3 brings the M3 improvements to the 20 round magazine form factor. All of the GEN M3 improvements are here, including the constant curve geometry and fully anti-tilt, low-friction follower, which is a change from our GEN M2, straight PMAG 20. This gives you the shorter length and easier manipulation while prone of a 20 round magazine, with all the reliability and durability of the GEN M3. Unlike with the 30 rounders, the 20 round GEN M3 will replace the GEN M2 offering in our product line.
The PMAG 10 GEN M3 brings GEN M3 technology to the smallest possible magazine size. Perfect for hunting applications with or without the addition of a limiter, depending on local hunting laws, and also for states where overall capacity is limited. The 10 round GEN M3 includes all of the benets of the GEN M3 line. Perfect for use with a bipod or when shooting off of a pack.
M AGA ZINES
10
11
M AGA ZINES
MAGPUL
MADE IN USA
MOE
INTRODUCING THE
During the development of the GEN M3 PMAG, we had some discussions about the future of the GEN M2. The GEN M2 is the magazine that has been proven under re, and trusted by American and Allied warghters, Law Enforcement, and recreational shooters for years. To discontinue a product that works as well as the GEN M2 didnt make sense to us. So, the GEN M2 PMAG will remain in the line as the MOE PMAG, and will join the rest of the Magpul Original Equipment line. Economies of scale and no longer including the dust cover allow us to offer the MOE PMAG line at very attractive prices bringing you even greater value from the combat-proven PMAG.
The GEN M2 PMAG is a lightweight 5.56x45 NATO (.223 Remington) AR15/M4 compatible magazine. It features advanced impact resistant polymer construction, and an easy to disassemble design with a ared oorplate for positive magazine extraction from pouches.
The PMAG 30 Window (5.56 NATO/.223 Remington) is a durable, lightweight, high reliability 30-round polymer magazine optimized for the AR15/M4. Otherwise identical to the standard PMAG, the PMAG 30 window features THEORY transparent MagLevel windows on both BASED sides of the body and has a painted PRODUCT THEORY indicator on the spring for quick BASED PRODUCT determination of approximate rounds remaining in the magazine.
M AGA ZINES
12
13
M AGA ZINES
MAGPUL
MADE IN USA
The PMAG 25 LR/SR GEN M3 (7.62 NATO/.308 Win) is a lightweight, high reliability 25 round polymer magazine for SR-25/M110/Mk11 ries and ries that utilize magazine specications compatible with these platforms. The PMAG 25 LR/SR brings GEN M3 improvements to the LR line along with more of a good thing in the form of 25 rounds of capacity. Keep track of those rounds with MagLevel functionality, for the rst time, now available in a 7.62 PMAG.
The PMAG 20 LR/SR GEN M3 brings the M3 improvements to the 20 round 7.62 NATO / .308 Winchester SR-25 magazine form factor. All of the GEN M3 improvements are here in the 20 round capacity form factor of our previous design. The PMAG 20 LR/SR GEN M3 will replace the MAG243 in our line.
THEORY BASED PRODUCT
The PMAG 10 LR/SR GEN M3 brings GEN M3 technology to the smallest possible magazine size. Perfect for hunting applications, depending on local hunting laws, and also for states where overall capacity is limited. The 10 round GEN M3 includes all of the benets of the GEN M3 line. Perfect for use with a bipod or when shooting off of a pack.
THEORY BASED PRODUCT
M AGA ZINES
14
15
M AGA ZINES
MAGPUL
MADE IN USA
PMAG 30G
MAG234 MSRP $27.95 5.56 NATO / .223 REmINGTON
MAG234-BLK
A 30-round 6.8 Remington SPC polymer magazine for PMAG 6.8 SPC Magwell Spec weapons, including the LWRC International SIX8 platform. Impact and crush resistant construction incorporates new GEN M3 polymer technology and manufacturing processes for enhanced strength, durability, and reliability to exceed rigorous military performance specications. Self-lubricating anti-tilt follower for increased reliability. Over-insertion stop on the spine helps ensure that the magazine will not overinsert on compatible weapons.
M AGA ZINES
USGI-spec stainless steel spring for corrosion resistance and eld compatibility.
THEORY Aggressive non slip texture at the front BASED and rearPRODUCT for superior grip.
The EMAG (Export MAGazine) is a lightweight 30-round 5.56x45 NATO polymer magazine that features a number of aesthetic and functional changes from the original PMAG. While the EMAG remains 100% compatible with the AR15/ M16 platform, its unique geometry is optimized for foreign-made weapons such as the HK 416, and British SA-80. To enhance compatibility with double and triple magazine pouches as well as aftermarket mag couplers, the EMAG features a slim, rib-less, anti-snag prole. Front-to-back and side-to-side dimensions have been adjusted to ensure compatibility with as many STANAG 4179 weapons as possible, including most non Colt-spec AR15 ries.
The PMAG 30G (5.56 NATO/.223 Remington) is a durable, lightweight, high reliability 30-round polymer magazine for the HK G36. The PMAG 30G features a four-way anti-tilt follower, constant-curve internal geometry, slim-line body for enhanced pouch compatibility, and THEORY MagLevel round indicator windows to BASED easily identify loaded round count. The PRODUCT PMAG 30G utilizes the same oor plate, lock plate, and Milspec black oxide coated stainless steel spring as the original PMAG 30 to ensure durability and performance in all environments.
16
17
M AGA ZINES
MAGPUL
MADE IN USA
PMAG 30 G
mag234 $27.95 HK G36 5.56/.223 30 BLK M2
M AGA ZINES
18
19
M AGA ZINES
MAGAZINE
MAGPUL
MADE IN USA
original magpuL
MAG001 MAG002 MAG003 MSRP $9.95 / 3-paCK MSRP $9.95 / 3-paCK MSRP $9.95 / 3-paCK 5.56 NATO MAGAZINES 7.62 NATO mAGAZINES 9MM PARA mAGAZINES NSN# 9mm: 1005-01-554-2864 (MAG003-BLK) NSN# 5.56mm: 1005-01-554-2864 (MAG001-BLK)
MAG001-BLK MAG001-FDE MAG001-FOL MAG001-odg MAG002-BLK MAG002-FDE MAG002-FOL MAG002-odg MAG003-BLK MAG003-FDE MAG003-FOL MAG003-odg
WHERE WE STARTED
The original product, the Magpul that started it all is still part of our offerings, at the same price it was initially offered. The idea of our founder Richard Fitzpatrick, a Reconnaissance Marine, looking for a better way to handle magazines coming out of issue pouches than the paracord loop common at the time, the Magpul has endured in our line. Value for money and intelligent design, two of the tenets that brought the Magpul into being, still guide our product efforts. Now, our magazine accessories category contains handling and enhancement solutions that improve function with a number of options depending on user needs.
The Magpul rubberized loop attaches to the bottom of the magazine to increase controllability and speed during high-stress tactical magazine changes. The original Magpul is based on the tried and true para-cord loops and duct tape tabs currently in use with special warfare units worldwide. Fits most aluminum, steel, and polymer magazines including the Magpul PMAG.
maglinK
MAG595 MSRP $17.95
MAG595-BLK
The MagLink 30 is a coupler for PMAG 30 AR/M4 GEN M2 MOE and PMAG 30 AR/M4 GEN M3 magazines which allows the user to attach two magazines together for more efcient speed reloads, and to keep an additional 30 rounds of ammunition accessible on the weapon at all times. The MagLink 30 features a two-piece bolt on design, and durable, lightweight reinforced polymer construction. Note: the MagLink 30 is not compatible with the rst generation PMAG 30, PMAG 20, EMAG, PMAG 30G, or PMAG 20LR.
M AGA ZINES
20
21
M AGA ZINES
MAGPUL
MADE IN USA
RANGER PLATE
MAG561 MAG212 MAG020 MSRP $14.95 / 3-paCK PMAG 30 GEN m3, PMAG 20 GEN m3, AND PMAG 10 GEN m3 (INCLUDING ALL WINDOWED VARIANTS) MSRP $14.95 / 3-paCK PMAG 30 GEN m2 MOE AND PMAG 20 GEN m2 (INCLUDING ALL WINDOWED VARIANTS) MSRP $19.95 / 3-paCK ALUmINUm USGI 30 ROUND mAGAZINES
MAG561-BLK MAG212-BLK MAG212-FDE MAG212-FOL MAG212-odg MAG020-BLK MAG020-FDE MAG020-FOL MAG020-odg
USGI L-PLATE
MAG024 MSRP $19.95 3-paCK ALUmINUm USGI 30 ROUND
MAG024-BLK MAG024-FDE MAG024-FOL MAG024-odg
MAG110-YEL
The PMAG Ranger Plate brings the speed and controllability of the original Magpul to the Magpul PMAG system. The reinforced polymer base has an overmolded rubber loop that provides positive control and impact protection. The PMAG Ranger replaces standard PMAG oor plates and features a para-cord hole for custom loop congurations. The overmolded Ranger Plate for USGI replaces the standard oor plate on USGI 30-round 5.56 NATO aluminum magazines.
The low prole overmolded L-Plate replaces the standard oor plate on USGI 30-round 5.56 NATO aluminum magazines, aiding in magazine control and acting as an impact bumper to shield the magazine against damage when dropped.
The Magpul Generation III Enhanced Self-Leveling Follower is a drop in replacement for the issued green or black USGI 30-round magazine followers. The 4-way anti-tilt design increases weapon reliability by eliminating many common magazinerelated malfunctions. Followers are made from self-lubricating nonhygroscopic resin.
M AGA ZINES
22
23
M AGA ZINES
MAGPUL
MADE IN USA
dummY rounds
MAG215 NSN: MSRP $4.95 5-paCK 1310-01-591-5927(MAG215)
MAG215-BLK
speedplate
MAG230 MSRP $14.95 3-paCK
MAG230-BLK
NSN: 1005-01-591-6113
The PMAG Round Limiters install in 10, 20, or 30 round GEN M3 magazines, reducing the magazine capacity by 5 or 10 rounds. Designed for sporting and hunting applications, installation of the Limiter is simple, tool-less, and requires no permanent modication of the magazine body.
Five dimensionally correct, solid, dummy rounds made from our proprietary hard polymer. Used for test feeding of magazines or other training, these can be cycled and ejected using the rifle action.
The Speedplate is designed for all Glock 9mm and .40 caliber magazines. When attached to the base of the magazine the Speedplate can improve speed reloads and assist in fully seating the magazine.
M AGA ZINES
24
25
M AGA ZINES
MAGPUL
MADE IN USA
26
27
MAGPUL
STOCKS
MADE IN USA
EVERY MAGPUL StOCK IS DESIGNED wItH tHE SAmE AttENtION tO DEtAIL, USABILItY, DURABILItY, AND QUALItY. EVERY StOCK FEAtURES A NON-SLIP BUttPAD OPtImIZED FOR StAYING PUt IN YOUR SHOULDER POCKEt AND USE wItH ARmOR wItHOUt BEING SO SOFt AS tO SNAG. WE KNOw tHAt DIFFERENt USERS HAVE DIFFERENt NEEDS, tHOUGH, AND NO ONE-FItS-ALL DESIGN wILL BE OPtImAL FOR EVERYONE, SO wE GIVE YOU OPtIONS.
CARBINE StOCKS
The MOE carbine stock provides the perfect lightweight stock when basic functionality is all that is desired or required. The CTR adds our exclusive friction lock, which adds rigidity to the stock/buffer tube lockup, and also a built-in QD sling attachment point. The CTR is perfect when a lightweight, solid carbine stock is required on a fasthandling rie. The STR takes the CTR form factor and adds battery storage tubes, which in addition to storage, provides a wide, solid cheek weld. The STR features a narrowed rear section where the width tapers inward to nearly as slim as the CTR, so as to not interfere with armor or chest rigs. The STR is perfect for everything from SBRs to Recce ries, and even on SPRs, due to the enhanced cheek weld. The ACS-L has an enhanced cheek weld that is narrower than the STR, but wider than the CTR. It is also longer than the MOE, CTR, and STR, which is a bonus for users with longer arms or those who like a bladed shooting stance, as solid cheek weld can be had farther forward than on the shorter stocks. The ACS-L also introduces the buttstock storage compartment, which is perfect
for storing lubricant, a boresnake, batteries, or other items. The ACS combines the extra length and buttstock storage compartment of the ACS-L with the battery storage tubes of the STR, to bring you a fullfeatured stock with extra-length, lots of storage, and excellent cheek weld. The ACS is popular on general purpose ries, recce builds, and SPR/DMR applications. When xed stock rigidity, solid cheekweld, fast adjustment, and near indestructibility are desired, the UBR is the stock to have. The UBR includes its own entry-length carbine receiver extension and provides unparalleled strength with the adjustability of a carbine stock and the solid cheek weld of a xed stock. The UBR includes a storage compartment with reversible door that can be removed to save weight. The UBR is exceptional on SPR/ DMR applications due to its solid cheek weld, and the extra weight of the UBR balances out heavier barrel proles or forend accessories like lights and lasers. Whatever your carbine application, there is a stock with our name on itthat has your name on it, with Magpul quality and intelligent design built in.
When a carbine type adjustment range is not needed, desired, or permitted, Magpuls xed MOE stock line provides the answer. Our Fixed Carbine Stock is an innovative option that provides the rigidity of a xed stock on your carbine buffer tube, perfect for replacing an adjustable carbine stock without gunsmithing or for locations that dont allow collapsible stocks. The MOE Rie Stock provides enhanced cheek weld and extra storage space, plus QD socket and monopod rail attachment points to work with your rie-length receiver extension for a rugged design optimized for rie platforms. The PRS brings full precision stock features to your AR platform with fully adjustable cheek riser and length of pull, an integrated monopod rail, and extended buttpad options. Available in two versions, one optimized for .223/5.56 and one for .308/7.62. Additionally, you can bring PRS functionality to your HK-91/G3 or FN/FAL with the PRS2, incorporating these same features to these classic battle rie platforms.
STOCK S
28
29
STOCK S
MAGPUL
MADE IN USA
The MOE Carbine Stock is a costeffective replacement for the standard M4 stock body, offering enhanced strength and ergonomics. The Magpul Original Equipment (MOE) stock offers Magpul engineering and material quality in an economical package. Utilizing a strong A-frame design, reinforced polymer construction, streamlined exterior, rubber butt-pad, and shielded operation lever, the MOE is a drop-in replacement for the standard M4 stock body.
The CTR Carbine Stock is a fully-featured drop-in replacement for the standard M4 stock body, offering enhanced strength, stability, and ergonomics. Designed for stability, the Compact/Type Restricted (CTR) stock utilizes a strong A-frame design, reinforced polymer construction, shielded operation lever, and a friction locking system to mitigate excessive stock movement. The CTR comes standard with dual-side QD sling mount and rubber butt-pad.
STOCK S
30
31
STOCK S
MAGPUL
MADE IN USA
The Magpul STR (Storage/Type Restricted) is a drop-in replacement buttstock for AR15/M4 carbines. A storage-capable version of the CTR, the STR has improved cheek weld and two water resistant battery tubes on a compact, reinforced polymer A-frame design. A shielded operation lever and supplemental friction locking system prevent accidental operation and minimize excessive stock movement for enhanced weapon stability and accuracy. The STR incorporates two integral sling loops, a reversible push-button QD sling mount, and a replaceable 0.30 rubber butt-pad which provides positive shoulder purchase to prevent slippage even with body armor or modular gear.
The Magpul ACS-L (Adaptable Carbine Stock - Light) is a drop-in replacement butt-stock for AR15/M4 carbines. A streamlined version of the ACS, the ACS-L utilizes the same center storage compartment and cheek weld but removes the battery tubes for a slimmer, lighter weight package.
STOCK S
32
33
STOCK S
MAGPUL
MADE IN USA
The ACS Carbine Stock is a drop-in replacement for the standard M4 stock body, offering enhanced strength, stability, battery/equipment storage, and improved cheek weld. The Adaptive Carbine/Storage (ACS) stock features a comfortable sloping cheek weld, robust reinforced polymer construction, dual-side battery storage tubes, an integral storage compartment, and friction locking mechanism to mitigate excess stock movement. 0.30 thick rubber buttpad included.
The UBR is an adjustable stock for the AR15/M4, designed to offer the same strength and stability as a xed stock with a consistent and comfortable cheek weld in any position. The Utility/Battle Rie (UBR) stock, features a xed cheek piece to provide a consistent cheek weld in any of its 8 positions. Designed to accommodate large-bore AR calibers and withstand severe impacts, the UBR comes standard with front and rear QD sling attachment points and 0.30 thick rubber butt-pad. Entry-length buffer tube included, compatible with standard carbine buffers and action springs.
STOCK S
34
35
STOCK S
MAGPUL
MADE IN USA
The MOE Fixed Carbine Stock provides a xed, non-collapsing stock option for carbine-length buffer tubes. The MOE Fixed Carbine Stock has a slim prole, improved cheek weld, and multiple sling attachment options, and is compatible with the ASAP Plate and PRS Extended Rubber Butt Pad. Installation is nonarmorer and does not require the castle nut or lock plate to be removed. Integrated footmans loop sling points and optional dual-side QD mounting points Compatible with ASAP Plate & PRS Extended Rubber Buttpads
The MOE Rie Stock is a simple, lightweight, cost-effective stock for the AR15/M16 and AR10/SR25 platforms, with an enhanced cheek weld, rubberized butt-pad, and internal storage compartment.
THEORY BASED PRODUCT THEORY BASED PRODUCT
The MOE Rie Stock is a drop-in replacement for A1 and A2 rie stocks utilizing the standard rie-length receiver extension (buffer tube) without the A2 spacer. Designed as a basic rie upgrade, the stock features an improved cheek weld prole, integral 1.25 sling loop, optional dual-side front and rear QD mounting points, replaceable antislip rubberized butt-pad, and internal storage compartment accessible through the rear storage door.
STOCK S
36
37
STOCK S
MAGPUL
MADE IN USA
The PRS is a eld precision stock for AR15/M16 and AR10/SR25 platforms, featuring tool-less length of pull and cheek piece height adjustment. Adjustable for length of pull and cheek piece height via aluminum detent knobs, the PRS (Precision Rie/Sniper) stock is intended for semi automatic sniper or varmint type ries. It installs on a standard rie-length receiver extension (buffer tube) without the A2 spacer, and includes a rubberized butt-pad.
The PRS2 is a eld precision stock for the FN FAL or HK G3/91, featuring tool-less length of pull and cheek piece height adjustment. Adjustable for length of pull and cheek piece height via aluminum detent knobs, the PRS2 (Precision Rie/ Sniper) stock is intended for semi automatic sniper or varmint type ries. The FAL variant installs on metric pattern ries. The G3/91 utilizes the factory standard buffer unit.
STOCK S
38
39
STOCK S
MAGPUL
MADE IN USA
PRS STOCK
mag307 mag308 $255.00 $255.00 RIfLe BUffeR tUBe RIfLe BUffeR tUBe 26.9 oZ. 13.30" - 14.30" 26.9 oZ. 13.80" - 14.80"
prs2 STOCK
MAG341 $255.00 FN FAL 30.2 oZ. 14.30" - 15.5" BLK FAL (METRIC) HKg3/91 MAG340 $255.00 HK g3/91 30.2 oZ. 15.00" - 16.20"
12.375" 12.375" BLK - FDE - FOL - ODG - GRY aR15 - m4 - aR10 - SR25 - m110
BLK - FDE - FOL - ODG - GRY - PNK aR15 - m4 - aR10 - SR25 - m110
BLK - FDE - FOL - ODG - GRY aR15 - m16 aR10 - SR25 - m110
STOCK S
40
41
STOCK S
MAGPUL
MADE IN USA
replaCement Butt-pads
MAG315 MAG316 MSRP $19.95 MSRP $19.95 0.30" MOE, CTR, STR, ACS, ACS-L, AND UBR 0.55" MOE, CTR, STR, ACS, ACS-L, AND UBR
MAG315-BLK MAG316-BLK
enHanCed Butt-pad
MAG317 MSRP $19.95
MAG317-BLK
CHeeK risers
MAG325 MAG326 MAG327 MSRP $19.95 MSRP $19.95 MSRP $19.95 0.25" MOE AND CTR STOCKS 0.50" MOE AND CTR STOCKS 0.75" MOE AND CTR STOCKS NSN#: 1005-01-591-6018 (mAG325-BLK) 1005-01-591-6035 (mAG326-BLK) 1005-01-591-6041 (mAG327-BLK) NOTE: maY interfere WitH CHarging Handle if installed on AR15/M4 rifles
MAG325-BLK MAG325-FDE MAG325-FOL MAG325-odg MAG326-BLK MAG326-FDE MAG326-FOL MAG326-odg MAG327-BLK MAG327-FDE MAG327-FOL MAG327-odg
NSN#: 1005-01-591-5966
Rubber Butt-Pads come standard with our carbine stocks and utilize a rm rubber that is designed for enhanced shoulder purchase and improved impact/drop mitigation. Commercial Butt-pad (0.55) may be used with all milspec MOE, CTR, STR, ACS-L, ACS and UBR stocks for 0.25 increased length-of-pull. All mounting hardware included.
The 0.70 thick Enhanced Rubber ButtPad can be installed on all UBR, ACS, ACS-L, STR and Milspec MOE/CTR stocks. The Enhanced Rubber Butt-pad can also be installed on Commercial MOE/CTR stocks, but may prohibit use of fully collapsed position. All mounting hardware included.
Clip on cheek risers for the MOE and CTR stocks. Raises cheek weld .25, .50, or .75 inch in height. These risers are for use on NON AR15/M4 applications as the riser will interfere with charging handle function. Originally designed for M14 carbine stock conversions.
NSN#: 1005-01-591-5976
NSN#: 1005-01-591-5982
NSN#: 5340-01-591-5639
TYPE 1 SGA SHOTGUN AND mOE RIFLE TYPE 2 DUAL SIDE UBR, STR, SGA, MOE RIFLE AND MOE FIXED CARBINE TYPE 3 ACS AND ACS-L
The PRS Extended Rubber Butt-Pad replaces the standard 0.30 thick rubber butt-pad, adding approximately 0.50 to the original length of pull. Compatible with PRS AR15/M16 and AR10/SR25. Uses existing mounting hardware.
The PRS2 Extended Rubber Butt-Pad replaces the standard rubber buttpad, adding approximately 0.50 to the original length of pull. Compatible with PRS2 for HK G3/91 and FAL. Uses existing mounting hardware.
The UBR Strike Plate is a heavy-duty replacement for the UBRs lower sling loop bracket. Incorporating an aggressive toothed pattern on the bottom, the Strike Plate can be used for various breaching operations as well as Close Quarters Battle butt-stroking maneuvers.
Sling mount kits for attaching pushbutton QD sling swivels to specic Magpul stocks. Heavy-duty black phosphate nished steel construction easily installs with stocks original hardware. Swivels not included.
STOCK S
42
43
STOCK S
MAGPUL
MADE IN USA
IN KANSAS ANYMORE
PHOTO: DIRECTOR OF PRODUCT mANAGEmENT, mARKETING, AND mAGPUL DYNAmICS (NOT IN KANSAS)
44
STOCK S
45
STOCK S
MAGPUL
sLing
MADE IN USA
SLING SYSTEM
46
47
SLING SYSTEM
MAGPUL
MADE IN USA
ms3 SLING
MAG503 MSRP $49.95
MAG503-COY MAG503-BLK
The MS4 Sling is a Dual-QD version of the standard MS3 Sling. With PushButton QD Sling Swivels in place of the standard Paraclips, the MS4 provides a two-to-one-point convertible sling option compatible with front and rear QD attachment points.
Optimized for use with the ASAP and RSA or MSA, the MS3 can switch quickly between 1-point and 2-point conguration. Made from custom nylon webbing chosen for its comfort and strength, the MS3 is easily adjustable for shooter size and preference. It also features a light weight, heavy duty, polymer and steel Paraclip to allow easy manipulation in emergency situations.
Filling the same mission requirement as the standard MS3, the MS3 QD can quickly switch between 1-point and 2-point conguration. The MS3 QD maintains material construction and specications identical to that of the standard MS3, but features a heavy duty push-button QD sling swivel for the 1-point (rear) weapon attachment rather than the Magpul Paraclip found on the standard MS3. This modication allows compatibility with QD sling cups commonly found on lower receivers, receiver end plates, and buttstocks.
SLING SYSTEM
48
49
SLING SYSTEM
MAGPUL
MADE IN USA
ASAP
MAG500
MAG500
MSRP $29.95
Replacing the standard carbine receiver end plate, the ASAP is a truly ambidextrous rear sling attachment point that provides over 180 degrees range of motion, allowing efcient transition from primary to secondary shoulders. All mounting hardware included. Made from Melonite nished steel, the ASAP replaces the standard carbine receiver end plate and is compatible THEORY with both Milspec and commercial BASED PRODUCT receiver extensions (buffer tubes).
The MSA (MOE Sling Attachment) attaches directly to the MOE Hand Guard, providing a forward sling attachment point for the Magpul MS3 and other clip-in sling systems. Like the RSA the MSA is precision cast steel, and is Melonite nished for wear and corrosion resistance.
THEORY BASED PRODUCT
RSA provides a forward sling attachment point for the Magpul MS3 and other clip-in sling systems. Made from Melonite nished, precision cast steel, the RSA attaches to 1913 Picatinny Rails. All mounting hardware included.
The RSA-QD provides a forward attachment point for the Magpul MS4 Sling and other push-button QD slings. It is Melonite nished steel, mounts on 1913 Picatinny rail, and places the attachment point at an angle optimized THEORY for comfortable two-point sling use BASED while maintaining easy push-button PRODUCT access.
SLING SYSTEM
50
51
SLING SYSTEM