Beruflich Dokumente
Kultur Dokumente
TLE 4279
Features Output voltage tolerance 2% 150 mA current capability Very low current consumption Early warning Reset output low down to VQ = 1 V Overtemperature protection Reverse polarity proof Adjustable reset threshold Very low-drop voltage Wide temperature range Green Product (RoHS compliant) AEC Qualified
Functional Description This device is an automotive suited voltage regulator with P-DSO-14-3, -8, -9, -11, 14 a fixed 5-V output, e.g. in a PG-DSO-8-16 package. The maximum operating voltage is 45 V. The output is able to drive 150 mA load. It is short circuit protected and the thermal shutdown switches the output off if the junction temperature is in excess of 150 C. A reset signal is generated for an output voltage of VQ < 4.65 V. The reset threshold voltage can be decreased by external connection of a voltage divider. The reset delay time can be set by an external capacitor. If the application requires pull-up resistors at the logic outputs (Reset, Sense Out) the TLE 4269 with integrated resistors can be used. It is also possible to supervise the input voltage by using an integrated comparator to give a low voltage warning.
TLE 4279
PG-DSO-8-16
S RADJ D 1 2 3 4 8 7 6 5
AEP01668
Q SO RO GND
Pin Configuration (top view) Pin Definitions and Functions (TLE 4279 G) Symbol Function Input; block to GND directly at the IC with a ceramic capacitor Sense input; if not needed connect to Q Reset threshold adjust; if not needed connect to ground Reset delay; to select the delay time, connect to GND via external capacitor Ground Reset output; open-collector output. Keep open, if not needed Sense output; open-collector output. Keep open, if not needed 5-V output; connect to GND with a 10 F capacitor, ESR < 10
RADJ D GND RO SO Q
Data Sheet
TLE 4279
PG-DSO-14-30
RADJ D GND GND GND GND RO 1 2 3 4 5 6 7 14 13 12 11 10 9 8
AEP02248
Pin Configuration (top view) Pin Definitions and Functions (TLE 4279 GM) Symbol Function RADJ D GND RO SO Q I SI Reset threshold adjust; if not needed connect to GND Reset delay; connect to GND via external delay capacitor for setting delay time Ground Reset output; open-collector output. Keep open, if not needed Sense output; open-collector output. Keep open, if not needed 5-V output; connect to GND via 10 F capacitor, ESR < 10 Ground Input; block to GND directly at the IC by a ceramic capacitor Sense input; if not needed connect to Q
Data Sheet
TLE 4279
Circuit Description The control amplifier compares a reference voltage, made highly accurate by resistance balancing, with a voltage proportional to the output voltage and drives the base of the series PNP transistor via a buffer. Saturation control as a function of the load current prevents any over-saturation of the power element. The reset output RO is in high-state if the voltage on the delay capacitor CD is greater or equal VUD. The delay capacitor CD is charged with the current ID for output voltages greater than the reset threshold VRT. If the output voltage gets lower than VRT (reset condition) a fast discharge of the delay capacitor CD sets in and as soon as VD gets lower than VLD the reset output RO is set to low-level. The time gap for the delay capacitor discharge is the reset reaction time tRR. The reset threshold VRT can be decreased via an external voltage divider connected to the pin RADJ. In this case the reset condition is reached if VQ < VRT and VRADJ < VRAQDJ,TH. Dimensioning the voltage divider (see Figure 4) according to:
(1)
the reset threshold can be decreased down to 3.5 V. If the reset-adjust-option is not needed the RADJ-pin should be connected to GND causing the reset threshold to go to its default value (typ. 4.65 V). A built in comparator compares the signal of the pin SI, normally fed by a voltage divider from the input voltage, with the reference and gives an early warning on the pin SO. It is also possible to superwise another voltage e.g. of a second regulator, or to build a watchdog circuit with few external components. Application Description The input capacitor CI is necessary for compensating line influences. Using a resistor of approx. 1 in series with CI, the oscillating circuit consisting of input inductivity and input capacitance can be damped. The output capacitor CQ is necessary for the stability of the regulating circuit. Stability is guaranteed at values 10 F and an ESR 10 within the operating temperature range. Both reset output and sense output are open collector outputs and have to be connected to 5 V output via external pull-up resistors 10 k. For small tolerances of the reset delay the spread of the capacitance of the delay capacitor and its temperature coefficient should be noted.
Data Sheet
TLE 4279
Trimming
RO
AEB01955
Figure 3
Block Diagram
Data Sheet
TLE 4279
Table 3
Tj = -40 to 150 C
Parameter Input Input voltage Input current Sense Input Input voltage Input current Reset Threshold Voltage Current Reset Delay Voltage Current Ground Current Reset Output Voltage Current Sense Output Voltage Current 5-V Output Output voltage Output current Temperature Junction temperature Storage temperature Symbol Limit Values Min. Max. 45 45 1 7 10 7 7 7 7 150 150 V V mA V mA V mA V V V mA C C internal limited internal limited internal limited internal limited Unit Notes
-40
-40
1
-40 -10
-0.3
50
-0.3
-0.3
-0.5
-10
-50
Data Sheet
TLE 4279
Table 3
Tj = -40 to 150 C
Parameter Operating Range Input voltage Junction temperature Thermal Data Junction-ambient Junction-pin
1) measured to Pin 4
Symbol
Unit
Notes
VI Tj Rthja Rthjp
-40
Data Sheet
TLE 4279
Table 4
Characteristics
VQ IQ Iq Iq Iq Vdr VQ VQ
V V V V V V A ms s
ID td tt
Data Sheet
TLE 4279
Table 4
Characteristics (contd)
1.24 1.16
ISI
-1
0.1
1) Drop voltage = VI - VQ (measured when the output voltage has dropped 100 mV from the nominal value obtained at 13.5 V input.)
Data Sheet
TLE 4279
1000 F
C 470 nF
Q
RADJ1 RADJ
CQ 22 F
TLE 4279
S
SI D GND RO RADJ SO
V VS
CD 100 nF
VQ
D
VD
GND
VRO VSO VRADJ RADJ2
AES01956
Figure 4
Measuring Circuit
VI
VQ V RT
t < t RR
VD V UD V LD V RO VRO, SAT td t RR
dV I D = dt C D
t Power-on-Reset Thermal Shutdown Voltage Dip at Input Undervoltage Secondary Spike Overload at Output
AED01542
Figure 5
Data Sheet
TLE 4279
VSI, Low
Low t
AED03049
Figure 6
Data Sheet
11
TLE 4279
V = 13.5 V V C = 1.0 V
40
80
120 C 160 Tj
40
80
120 C 160 Tj
1.5 1.4
Tj = 125 C 200 Tj = 25 C 100
300
30
60
90
120
mA
180
0.9 -40
40
80
120 C 160 Tj
Data Sheet
12
TLE 4279
q mA
25
20 RL = 33
15
RL = 50
10
RL = 50 RL = 100 RL = 200 0 10 20 30 40 V 50 V
8 V
V 10
5.0
4.9
4.8
1.1
4.7
1.0 -40
40
80
120 C 160 Tj
4.6 -40
40
80
120 C 160 Tj
Data Sheet
13
TLE 4279
Q mA
300 250
q mA
10 V = 13.5 V Tj = 25 C 8
Tj = 25 C
6
Tj = 125 C
4
10
20
30
40 V 50 V
20
40
60
80
mA
120
10
20
30
40 mA 50
Data Sheet
14
TLE 4279
Package Outlines
0.35 x 45
1.75 MAX. 0.175 0.07 (1.45)
4 -0.21)
0.19 +0.0 6
0.1
B
6 0.2
0.64 0.25
0.2 M A B 8x
Index Marking 1
5 -0.21)
1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Lead width can be 0.61 max. in dambar area
GPS01229
Figure 7
Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).
You can find all of our packages, sorts of packing and others in our Infineon Internet Page Products: http://www.infineon.com/products. SMD = Surface Mounted Device Data Sheet 15 Dimensions in mm Rev. 2.4, 2007-03-20
8 MAX.
TLE 4279
0.35 x 45
1.75 MAX.
C
4 -0.2
1.27
2) 0.41+0.10 -0.06
B
0.1
0.2 M A B 14x
8 60.2
0.64 0.25
14
0.2 M C
1 7 1) 8.75 -0.2
Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Lead width can be 0.61 max. in dambar area
GPS01230
Figure 8
Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).
You can find all of our packages, sorts of packing and others in our Infineon Internet Page Products: http://www.infineon.com/products. SMD = Surface Mounted Device Data Sheet 16 Dimensions in mm Rev. 2.4, 2007-03-20
8MAX.
1)
0.19 +0.06
TLE 4279
Revision History
Date
Changes
2007-03-20 Initial version of RoHS-compliant derivate of TLE 4279 Page 1: AEC certified statement added Page 1 and Page 15f: RoHS compliance statement and Green product feature added Page 1 and Page 15f: Packages changed to RoHS compliant version Legal Disclaimer updated
Data Sheet
17