Beruflich Dokumente
Kultur Dokumente
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 Customer Address Plant Location Service of Unit: Size Surf/unit (eff.) Fluid allocation Fluid name Fluid quantity, Total Vapor (In/Out) Liquid Noncondensable Temperature (In/Out) Dew / Bubble point Density (Vap / Liq) Viscosity Molecular wt, Vap Molecular wt, NC Specific heat Thermal conductivity Latent heat Pressure Velocity Pressure drop, allow./calc. Fouling resist. (min) Heat exchanged Transfer rate, Service PV Engineering Waterloo, ON Hot oil heater 17 / 96 213.7 ft2 Job No.: Reference No.: Proposal No.: Date: August 24, 2010 Rev. 2 Item No: E-101 Type BEM Hor Connected in 1 1 parallel Shells/unit 1 213.7 ft2 Surf/shell (eff.) PERFORMANCE OF ONE UNIT Shell Side Tube Side lb/h lb/h lb/h lb/h 10443 10443 0 0 10443 0 116667 116667 0 116667
in
series
BTU/(lb*F) 1.4586 / / 1.1674 / 0.5199 / 0.5641 BTU/(ft*h*F) 0.039 / / 0.301 / 0.079 / 0.071 BTU/lb psi 1250 1249.96 30 26.86 ft/s 2.93 6.5 psi 13.95 0.05 10 3.14 ft2*h*F/BTU 0.0005 0.001 0.0012 Ao based MTD corrected 6273921 BTU/h 140.31 F 209.93 Dirty 209.91 Clean 326.28 BTU/(h*ft2*F) CONSTRUCTION OF ONE SHELL Sketch Shell Side Tube Side Design/Vac/Test pressure FV 150 psi 1400 / / / / Design temperature 650 650 F Number passes per shell 4 1 Corrosion allowance 0.0625 0.0625 in 6 900 ANSI 1 Connections 4 In in 1 / / 300 ANSI Size/rating Out 3 900 ANSI 1 4 1 / / 300 ANSI Nominal Intermediate 900 ANSI / / 300 ANSI Tube No. 104 TksAvg 0.083 Length 96 in Pitch 1.25 in OD 1 in Tube type Plain Material Carbon Steel Tube pattern 30 Shell Carbon Steel ID 17.25 OD 19 in Shell cover Channel or bonnet Carbon Steel Channel cover Tubesheet-stationary Carbon Steel Tubesheet-floating Floating head cover Impingement protection Rods Baffle-crossing Carbon Steel Type Single segmental Cut(%d) 24.7 V Spacing: c/c 15.5 in Baffle-long Seal type Inlet 15.9375 in Supports-tube U-bend Type Bypass seal Tube-tubesheet joint Exp. 2 grv Expansion joint Carbon Steel Type Flange and flued (TEMA) RhoV2-Inlet nozzle 98 Bundle entrance 14 Bundle exit 38 lb/(ft*s2) Gaskets - Shell side Spiral-Wound Metal Fib Tube Side Spiral-Wound Metal Fib Floating head Code requirements ASME Code Sec VIII Div 1 TEMA class B - chemical service Weight/Shell 3709.1 Filled with water 4554.4 Bundle 1198.5 lb Remarks
T2 S3 T1 S2 S1
Page
HC Heat Transfer Solutions Inc. www.hcheattransfer.com 1-877-542-1214
of 5
Rev. 1 ft2
2 series
6 Size 7 Surf/Unit(eff) 8 9 10 11 12 13
Page
of 5
Connected in Surf/Shell(eff)
NOTES 1234Two (2) rows of impingement rods on a 30 deg layout are to be used for impingement protection Baffles to have a 1" V notch at the bottom The shell inlet nozzle is to be located on the side Dummy tubes (6) are to be installed in the horizontal pass partition lane.
Page
of 5
Connected in Surf/Shell(eff)
Tubesheet Layout
Shell inside diameter F ront head inside diameter Outertube limit T ube number T ube O.D. T ube pitch T ube pattern T ube passes T ie rod number T ie rod diameter Sealing strips (pairs) Baffle type Impingement protection T ube length Shell Side Inlet Nozzle Inside Diameter Shell Side Outlet Nozzle Inside Diameter Shell Side Outlet Nozzle Inside Diameter
Cu stome r: H&C H eat Tra nsfe r So l utions Ad dres s: Sarni a , O N Se rvice o f U n it: Ite m No.:E-10 1
in in in
in in
1. 1.25 30 4 -1
in
in in in in
Tube Layout
Design Codes ASME Code Sec VIII Div 1 T E MA B - chemical service
1.0 0
24
28
Drawing Number
Custom erSpecifications
1.2 5 24 28
Revision
Date 24/08/2010
Dwg.
App.
Page
of 5
Setting Plan
V iews on arrow A 3.25 T2
A
11.125 7.125 T2 6.5 S3
3.25
T1
S1 S3
T1
S2 16
S2 19.1875 57.625
S1
2.0
2.0
Ref S1 S2 S3 T1 T2
Nozzle Data Standard 900 ANSI W eld 900 ANSI W eld 900 ANSI W eld 300 ANSI W eld 300 ANSI W eld
Design Data Design Pressure Design T emperature F ull Vacuum Corrosion Allowance T est P ressure Number of Passes Radiography PWHT Internal V olum e
C u sto me r : H&C H ea t Tr a n sfe r So lutio n s Ad dr e s s : Sar n ia , O N Se r vic e o f Un it: Ite m N o .:E- 10 1 D a te: Au g 20 1 0 R ev N o .: 1 J ob N o .:
Design Codes ASME Section VII I Div. 1 T EMA B Customer Specificat ions
ft
12. 5125
4.4291
Empty 3709 lb
Bundle 1198 lb
Revision
Dwg.
Chk.
App.
Page
of