Beruflich Dokumente
Kultur Dokumente
A few things to keep in mind while completing this activity: 1. 2. 3. Do not use the browser Back button or close or reload any exam windows during the exam. Do not close Packet Tracer when you are done. It will close automatically. Click the Submit Assessment button to submit your work.
Introduction
In this practice Packet Tracer Skills Exam, you will:
finish the configuration of a partially configured network establish connectivity to the UK and the Internet through the use of static and dynamic routing
Addressing Table
Device Interface
S0/0/0 S0/0/1 US-HQ S0/1/0 S0/1/1 Lo0 Fa0/0 Fa0/1 US-R1 S0/0/0 Lo0 Fa0/0 Fa0/1 US-R2 S0/0/0 Lo0 Fa0/0 ServerLAN Fa0/1 Lo0 US-Admin US-PC2 US-PC3 www.xyzcorp.com NIC NIC NIC NIC 192.168.20.242 172.16.0.2 192.168.20.97 192.168.20.114 172.16.0.3 192.168.20.66 192.168.20.94 192.168.20.62 192.168.20.98 255.255.255.252 255.255.255.255 255.255.255.240 255.255.255.248 255.255.255.255 255.255.255.224 255.255.255.224 255.255.255.192 255.255.255.240 n/a n/a n/a n/a n/a 192.168.20.65 192.168.20.65 192.168.20.1 192.168.20.97 192.168.20.246 172.16.0.1 192.168.20.65 192.168.20.113 255.255.255.252 255.255.255.255 255.255.255.224 255.255.255.248 n/a n/a n/a n/a
Address
192.168.20.245 192.168.20.241 64 .100.50.2 128.107.25.1 172.16.0.4 192.168.20.1 192.168.20.118
Subnet Mask
255.255.255.252 255.255.255.252
Default Gateway
255.255.255.192 255.255.255.248
n/a
Note: The password for user EXEC mode is cisco. The password for privileged EXEC
mode is class.
Configure and activate all interfaces for US-R2 that are listed in the addressing table.
US-R2 (config)# int Fa0/0 US-R2 (config-if)# ip add 192.168.20.65 255.255.255.224 US-R2 (config-if)# no shut US-R2 (config-if)# exit US-R2 (config)# int Fa0/1 US-R2 (config-if)# ip add 192.168.20.113 255.255.255.248 US-R2 (config-if)# no shut US-R2 (config-if)# exit US-R2 (config)# int S0/0/0 US-R2 (config-if)# ip add 192.168.20.242 255.255.255.252 US-R2 (config-if)# no shut US-R2 (config-if)# exit US-R2 (config)# int Lo0 US-R2 (config-if)# ip add 172.16.0.2 255.255.255.255 US-R2 (config-if)# no shut US-R2 (config-if)# exit
Configure the Fa0/1 interface on US-R1 with the last IP address in the subnet.
US-R1 (config)# int Fa0/1 US-R1 (config-if)# ip add 192.168.20.118 255.255.255.248 US-R1 (config-if)# no shut US-R1 (config-if)# exit
c. Verify connectivity.
Explore the network to determine the IP addressing of the serial interfaces that USHQ shares with US-R1 and US-R2. Remotely access US-HQ. US-R1# telnet 192.168.20.245
Using the next hop address 128.107.25.2, configure one summary static route on US-HQ to include only the subnets used and reserved for the UK. The UK subnets are listed in the following table:
UK Subnets
10.10.0.0/24 10.10.1.0/24 10.10.2.0/25 10.10.2.128/25 10.10.3.0/25 10.10.3.128/26 10.10.3.192/27 10.10.3.224/28 10.10.3.240/30 10.10.3.244/30 10.10.3.248/30 10.10.3.252/30
Configure a default route on US-HQ to send to the Internet all other traffic for destinations that are not found in the US-HQ routing table. Use the outbound interface argument.
Niestety drukowanie dokumentw z serwisu Scribd nie dziaa zbyt dobrze w Twojej przegldarce. Zachcamy do pobrania On US-HQ, do not advertise the subnet to the Internet or the subnet to go w formacie PDF i skorzystania z czytnika plikw PDF, aby go wydrukowa. UK.
HQ(config)# router ospf 3 Pobieranie i drukowanie HQ(config-router)# network 192.168.20.244 0.0.0.3 area 0 HQ(config-router)# network 192.168.20.240 0.0.0.3 area 0
US-R1 (config-router)# network 192.168.20.0 0.0.0.63 area 0 US-R1 (config-router)# network 192.168.20.112 0.0.0.7 area 0 US-R1 (config-router)# network 192.168.20.244 0.0.0.3 area 0
US-R2 (config)# router ospf 3 US-R2 (config-router)# network 192.168.20.64 0.0.0.31 area 0 US-R2 (config-router)# network 192.168.20.112 0.0.0.7 area 0 US-R2 (config-router)# network 192.168.20.240 0.0.0.3 area 0
Disable OSPF updates out interfaces where there are no OSPF neighbors available.
HQ(config-router)# passive-interface s0/1/0 HQ(config-router)# passive-interface s0/1/1 US-R1 (config-router)# passive-interface fa0/0 US-R2 (config-router)# passive-interface fa0/0
Configure US-HQ to send the default route to US-R1 and US-R2 in OSPF updates.
Change the hello interval to 30 seconds on US-R1 and US-R2 for the LAN that these two routers share with ServerLAN.
(f0/0) (f0/1)
Verify that the routing tables on US-R1, US-R2, and US-HQ contain all the expected routes. It may be necessary to shutdown and then reactivate interfaces to force OSPF to converge.
To test the static route to UK, successfully ping between US-HQ and UK-PC1. To test the OSPF neighbor establishment with ServerLAN, successfully ping between US-Admin and www.xyzcorp.com. To test end-to-end connectivity between the US and UK, successfully ping between US-PC2 and UK-PC3. To test the default route, successfully ping the Cisco Server from US-Admin.
Version 1.0 Created in Packet Tracer 5.3.2.0027 and Marvel 1.0.1 All contents are Copyright 1992 - 2011 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.