Beruflich Dokumente
Kultur Dokumente
Proporcionar al participante conocimientos de operacin del equipo de teleproteccin de lneas GARD 8000.
Objetivo especifico:
El participante identificar los conceptos y principios importantes, que le permitir un mejor entendimiento de operacin.
Ing. Jess Gpe. Ruiz Gmez Ing. Rodrigo Gutierrez
3/09/2012
Hoy: RFL es una empresa de comunicaciones dedicada al diseo y fabricacin de equipos de comunicacin y relevadores de proteccin para uso en ambientes agresivos, en la industria elctrica y del transporte.
65%
Domstico Internacional
5%
20%
Asia
25%
15%
Los Productos
PARTE 1
FUNDAMENTOS TELEPROTECCION ESQUEMAS DTT / POTT / PUTT / DAG / DAC / ETC COORDINACIN CON PROTECCIONES DESEMPENO DE TPS (DEPENDABILITY VS SECURITY) NORMATIVA DE EQ TELEPROTECCION IEC & IEEE HARDWARE LOGICAS DE OPERACION
S.E. B
S.E. A
INT. LINEA
INT. LINEA
INPUTS
OUTPUTS
INPUTS
IEC standards:
IEC 60834-1 Teleprotection equipment of power systems - Performance and testing Part 1: Narrow-band systems (First edition, 1988) Part 1: Command systems (Second edition, 1999) IEC 60834-2 Performance and testing of teleprotection equipment of power systems Part 2: Analogue comparison systems (First Edition 1993)
CIGRE publications:
"Teleprotection Guide", Study Committees 34 + 35, Joint Working Group on Teleprotection, 1969; Revised Version "Protection Systems Using Telecommunication", 1985 Revised Version "Protection Using Telecommunications", 2000 (in preparation)
Rele de proteccion
Teleproteccion
Enlace fisico
Telecomunicacion
Teleproteccion
Rele de proteccion
Tipo de Informacion:
Seales Continuas
Magnitude and/or phase of power frequency currents Magnitud y/o corrientes
Comandos (on/off)
Trip / do not trip
Proteccion de Distancia
Caracteristicas tipicas de la proteccion por Zona/Tiempo
(Typical stepped distance/time characteristics)
Operating Time
ZONE 3
ZONE 2
TA3 TB2 C
A RA
ZONE 1
TA2
B RB
TB1
TA1
RC
Distance
A, B, C Subestaciones RA,RB, RC Relevadores de proteccion TA1, TA2, TA3 Tiempos de operacion, Rele A TB1, TB2, TB3 Tiempos de operacion, Rele B
PROTECCIN DE FALLA DE
INTERRUPTOR
Es una proteccin de respaldo local que abre los interruptores adyacentes apara eliminar una falla cuando la proteccin primaria mando disparo del interruptor y este no abre, por cualquiera de los siguientes motivos: a) Perdida de voltaje de control b) Falla de los equipos asociados de control c) Falla del mecanismo del interruptor
ESQUEMA PUTT
Disparo Permisivo Transferido de Bajo Alcance. Su finalidad es enviar seal de operacin al otro extremo, al garantizar que la falla esta dentro de la Lnea protegida, S y Solo S ,la Zona 1 de un extremo esta operada y la Zona 1 o 2 del otro extremo esta activada . Tambin se le conoce como Aceleracin de Zona 2 (TX1).
Proteccion de Distancia
Disparo permisivo de bajo alcance (PUTT)
(Permissive Underreach Transferred Tripping)
B F LBC C
GARD
B, C Substations LBC Protected line section RBC,RCB Protection relay BC1, CB1 Zone 1 reach, 85% of line section
F L
ESQUEMA PUTT
Ventajas: Facilita disparos rpidos en ambos extremos, ya que acelera el
POTT:
Disparo Permisivo Transferido de Sobre Alcance. Su finalidad es enviar seal de operacin al otro extremo, al garantizar que la falla esta dentro de la Lnea protegida, S y Solo S ,las Zonas 2 de ambos extremo estn operadas.
Proteccin de Distancia
Disparo permisivo de sobrealcance (POTT)
(Permissive Overreach Transferred Tripping)
B F LBC C
RBC
GARD
GARD
B, C Subestaciones LBC Seccion Protegida de la linea RBC,RCB Reles de Proteccion BC1, CB1 Zona 1 alcance, 130% de la seccion de linea
F L
POTT:
Esquema POTT Ventajas: Facilita disparos rpidos en ambos extremos, ya que se activan las
zonas 2. El esquema es seguro, ya que solo opera para fallas dentro de la lnea.
Desventajas: Requiere llavear el canal cuando un interruptor esta abierto
Requiere que se activen las zonas 2 de ambos relevadores y depende de varios equipos. En lneas paralelas puede sacar disparos incorrectos, por el efecto de cambio de direccin de las corrientes (inversion de corrientes). No funciona cuando el canal esta fuera
POTT
Z2 Top = Z1 Z1
C A
21 Z1 TX1 RX1 Z2 21
C A
RX1 TX1
Proteccion de Distancia
Direct Transfer Tripping
B F LBC C
RBC
NSD
NSD
B, C Subestaciones LBC Seccion de linea Protegida RBC,RCB Reles de proteccion BC1, CB1 Zone 1 Alcance, 85% de la seccion de linea
F L
POTT
Z2
C
21 21
C A
TX1 RX1
RX1 TX1
DTD
Z1 ab
C A
21
C A
Fab
Z1 ab 21
DTD :
Disparo Transferido Directo. Su finalidad es enviar seal de Disparo Directo al otro extremo cuando uno de los Dos esquemas opera para fallas entre fase, es decir, el envi de la seal de cualquiera de los extremos garantiza la apertura de los interruptores en el otro extremo de la Lnea protegida. ( TX2 ) Este esquema es activado por la operacin de los relevadores de Distancia cuando operan de manera tripolar (Z2, Z3, fallas bifsicas y traficas), operacin del 67N, 87B, 50FI.
Proteccin de Transformador
Ejemplo de Disparo Directo
TPS B P L C TPS
P L Hilo piloto HV Transmission Line or -Cable
Disturbance, Impairments
Missing Command
Unwanted Command
Dependability (DISPONIBILIDAD)
Security (SEGURIDAD)
Operacion de Seccionadores (Isolater / breaker operation) Armonicos (50/60 Hz harmonics, pilot cables) Efecto Corona (Corona noise, PLC channels) Desbalances (Fading, microwave channels) Oscilacion (Jitter, digital networks) Sincronia (Temporary loss of synchronism, digital networks) Interrupcion (Signal interruptions) etc.
Disponibilidad
(Dependability= Probability of missing command)
El tiempo de deteccion en el rele (Relay-time fault detection) TREL La transmision del comando (Command transmission time) TAC La apertura del interruptor (Switching delay of line breaker) TBR
TBR
40 ms
Objetivo (Target) : TTotal = Menor a 100 ms, En el peor caso = 4.5 a 5 ciclos max. (50 Hz)
PROTECCIONES
GARD 8000
+127 vcc
2
Tx
L1 10uH
Tx1
+127 vcc
-127 vcc
Fuente
Tx
Regist.
UTR
Cuando el equipo de Teleproteccin requiera Voltaje Externo, ste voltaje deber ser de 127 Vcc, tomados del banco de bateras de la Subestacin
Connecting to a PC
Ethernet Port
PASOS A SEGUIR PARA ENTRAR AL EQUIPO DE TELEPROTECCION GARD 8000 1.- CONFIGURAR LA PC CON UNA IP DENTRO DE LA SUBRED DEL GARD EN ESTE CASO PARTICULAR LA IP DE LA PC ES 192.168.1.100 MASK 255.255.255.0 2.- ENTRAR AL SOFTWARE GARD 8000, VA A PEDIR USARIO: Admin PASSWORD: Admin 3.- DENTRO DE ESTE SOFWARE TE VA A SOLICITAR OTRA IP PARA RECONOCER AL GARD PARA ESTE CASO : IP: 192.168.1.1 PARA LA S.E. DEMEX MASK 255.255.255.0 IP: 192.168.1.4 PARA LA S.E. IXTEPEC MASK 255.255.255.0 4.- USER NAME: PASSWORD:
Dynamic content
Actual system population is shown
Cyber Security
Note: All GARD 8000 Front Ethernet ports are preconfigured to an IP address of 192.168.1.1 at the factory. Nota: todos los GARD 8000 vienen configurados los puertos frontales para una direccion IP 192.168.1.1 de fabrica
CLICK
8. Click on OK, and then click on the next OK button. 9. You have now successfully changed the IP address of your PC. 10. You will have to restart your computer for settings to take affect.
System Administrator
Administrator Login
NOTE: There is no backdoor for the Admin password. The default password is Admin but when changed, the actual password has to be used. Please contact the factory for password recovery procedure!!!!!
System Administrator
Access Administrations Page
System Administrator
Access Administrations Page:
Level 1, Read-only Level 2, Read-only, Test Functions Level 3, Test, Set, Configurations Level 4, Administrator Operations only. The default user Admin is always a Level 4. Each user is individually password protected. Strong passwords with up to 16 characters may be used. Access levels can be configured separately for each port. For instance, the rear port can be set to allow read-only while the front port can allow setting changes.
Authentication A list of approved IP addresses can be configured for remote access. Unused Ports All unused ports in GARD 8000 are closed. Firewalls and encryption GARD 8000 does not provide any firewall or encryption. Security should be considered on the network level.
Major Alarm Minor Alert Indicators Tool Bar w/Dropdown Pages Click Here Chassis Module Front and Rear
Chassis Configuration
All functional configuration, Status, Testing etc. is accessed via the top toolbar and the dropdown menus. Clicking on the Specific module will allow you to view or configure the module.
Click on Controller
This file is a .ZIP file and Contains all file applicable for operation the Chassis
First two files are the System Logic Flies And MUST be loaded in a specific order .TXT is loaded first .EDN is loaded second
CLICK
Chassis Configuration
Choose Controller
NOTE: Clicking on Settings and Selecting Chassis Configuration Settings will bring up this screen Use BACK Button on the Browser to return to last page.
GARD 8000
INPUT MODULE SETTINGS
GARD 8000
OUTPUT MODULE SETTINGS
GARD 8000
DIGITAL TPS CHANNEL SETTINGS
Click on TPS Digital Channel requires a Communication Channel This will be the G.703 located on the PS I/O
Digital TPS
Click on Edit
Click here to Clear Existing SOE Records Click here to Change Record Information
SOE Configuration
Allows User To enter Names for SOE Triggers Labels, Logic Bits, LED Colors and Types
Allows User To give names To each bit other than Default names
CLICK
Input Mapping
Allows User To Map any Logic Input To any Physical Input
Output Mapping
Allows User To Map Logic Output To any Physical Output
Option Settings
Allows User To set the Input to Function For One or Two input devices
Timer Settings
Allows User To change the Times for Specific Applications Timer are Pre-defined in Logic
Command Extend Means the Decay Time Time Delay Means The Attack Time
Communications Status
GARD 8000
Communications Status
GARD 8000
Communications Status
Click Here
Chassis Testing
GARD 8000
System Testing
Allows testing of the INPUTS, OUTPUTS, INTERFACE MODULES (Local, Remote Loopbacks), and SYSTEM MODULES
Input test
Warning
Remember Output will Follow the Input Execute Test Forces Input To the Defined state
Output test
If configured Should have And Minor Alarm When Input or Outputs Are Active
Input Test
For off-line configuration and settings Save file, save as txt, print, compare,