Beruflich Dokumente
Kultur Dokumente
page 1
Material thickness Cross-sectional area Weight of girder Material Elastic limit (yield strength) Permissible tensile stress1 Permissible tensile stress2 Modulus of elasticity Shear modulus
t [in] (s [mm]) A [in2] (A [mm2]) [lb-ft] ([kg/m]) f y,k [ksi] (f y,k [N/mm2])
MI-90 0.1378 (~10 ga) (3.5) 1.55 (1002.6) 6.34 (9.43) 34 (235.0) 22.10 (152.6) 20.40 (141) 30458 (210000) 11748 (81000) 75 2.77 (115.34) 1.56 (25.63) 1.33 (3.39) 2.77 (115.34) 1.56 (25.63) 1.33 (3.39) 3.73 (155.56) 2.76 45.25
MI-120 0.1575 (~8 ga) (4.0) 2.13 (1375.7) 8.47 (12.60) 34 (235.0) 22.10 (152.6) 20.4 (141) 30458 (210000) 11748 (81000) 75 6.38 (265.78) 2.70 (44.30) 1.73 (4.40) 4.17 (173.58) 2.35 (38.57) 1.40 (3.55) 7.13 (297.02) 4.37 71.63
Surface Hot-dip galvanized (acc. to ASTM A 123) Cross-section values y-axis Moment of inertia Section modulus Radius of gyration Cross-section values z-axis Moment of inertia Section modulus Radius of gyration Torsion data Torsional moment of inertia Torsional section modulus Torsional section modulus
1)
l y [in4] (l y [cm4]) Wy [in3] (Wy [cm3]) i y [in] (i y [cm]) l z [in4] (l z [cm4]) S z [in3] (Wz [cm3]) r z [in] (iz [cm]) l t [in4] ( l t [cm4]) Wt = 2 * A Bredt * t [in3] Wt = 2 * A Bredt * t [cm3]
The permissible stress is calculated from F y,k / G/Q with = 1,4. D results from higher yield strength due to cold forming in accordance with DAST-RILI016, issued 1992: D = fyk / M with M = 1.1 (Eurocode 3) The permissible stress is calculated from F y,k / G/Q with = 1.67 (Allowable Stress Design, ASD)
2)
page 2
MI girder
Advantages Torsionally rigid girder. Pipes may be mounted on all four sides simultaneously. Scale marks facilitate installation /cutting to length. Crimped-in depression for 100% compatibility with MQ channel system.
S235 JRG2 (DIN 10025), ASTM A283 (C) Hot-dip galvanized 3 mils (75 m) DIN EN ISO 1461, ASTM A123
115/16" (50)
Length ft (m)
Ordering designation
Item no.
Packaged in lengths of
1 15/16" (50)
page 3
S235 JRG2 (DIN 10025), ASTM A570 (36) Hot-dip galvanized 2.2 mils (55 m) DIN EN ISO 1461, ASTM A153
2 15/16" (75)
3 15/16" (100)
5
MI- 90 MI-120
MIC-90-U MIC-120-U
304803 304804
4 4
MI-90
/16" (8)
7 9/16" (192)
2x
page 4
S235 JRG2 (DIN 10025), ASTM A570 (36) Hot-dip galvanized 2.2 mils (55 m) DIN EN ISO 1461, ASTM A153
Note Designed for cantilever applications. May be supported at only one end.
5 1/2" (140)
5/ 16" (8)
MI-90
8.708 (3.95)
MIC-90-L
304805
2x
4x
12 3/8" (315)
2 15/16" (75)
2x
2x
page 5
S235 JRG2 (DIN 10025), ASTM A570 (36) Hot-dip galvanized 2.2 mils (55 m) DIN EN ISO 1461, ASTM A153
/16" (8)
4 3/4" (120)
MI-90/MI-120
4.497 (2.04)
MIC-T
304807
2x
2 15/16" (75)
8 11/16" (220)
2x 2x
Note: To use on both sides
2x
page 6
S235 JRG2 (DIN 10025), ASTM A570 (36) Hot-dip galvanized 2.2 mils (55 m) DIN EN ISO 1461, ASTM A153
MI-90 MI-120
MIC-90-E MIC-120-E
304809 304810
2 2
9 13/16" (250)
MI-90
8x
8x
9 13/16" (250)
4x
4x
MI-120
8x
page 7
S235 JRG2 (DIN 10025), ASTM A570 (36) Hot-dip galvanized 2.2 mils (55 m) DIN EN ISO 1461, ASTM A153
2 1516 6 12 (75165) 2 1516 6 12 (75165) 6 12 9 14 (165235) 9 14 11 1316 (235300) 2 1516 6 12 (75165) 6 12 9 14 (165235) 9 14 11 1316 (235300)
9.634 (4.37) 15.741 (7.14) 18.938 (8.59) 22.575 (10.24) 16.623 (7.54) 19.820 (8.99) 23.479 (10.65)
2 2 2 2 2 2 2
5 1/2" (140)
1/
x 1/2" (13)
D C B
1/ 2" (12)
D C B
1/ 2" (12)
5 1/2" (140)
5 1/2" (140)
11 3/16" (300)
5 7/8" (150)
5 7/8" (150)
9
B
MI-90
MI-120
6 1/8" (155) 6 1/8" (155) 8 11/16" (220)
MI-90
9
8 11/16" (220)
/16" (14)
3 1
/16" (14)
3 15/16" (100)
Note: + Designed for cantilever applications. May be supported at only one end.
2x
2x
page 8
S235 JRG2 (DIN 10025), ASTM A570 (36) Hot-dip galvanized 2.2 mils (55 m) DIN EN ISO 1461, ASTM A153
2 2 2
5 1/2" (140)
3 15/16" (100)
1/
2" (12)
/16" (15)
5 1/2" (140)
9/ " (15) 16
7 7/8" (200)
MI-90
Note: + Designed for cantilever applications. May be supported at only one end.
2x
2x
page 9
S235 JRG2 (DIN 10025), ASTM A570 (36) Hot-dip galvanized 2.2 mils (55 m) DIN EN ISO 1461, ASTM A153
5/
16" (8)
MI-90
5.049 (2.29)
304826
1x
1x
Ordering designation
Item no.
Package contents
4 1/8" (105)
0.772 (350)
MQP-45-F
304164
1
9
45
/16" (14) 1 5/8" (41) 1 5/8" (42)
page 10
3 15/16" (100)
MIC-C90-U
steel connection concrete connection Technical data Material: Galvanizing: S235 JRG2 (DIN 10025), ASTM A570 (36) Hot-dip galvanized 2.2 mils (55 m) DIN EN ISO 1461, ASTM A153
MI-90/MI-120
Set besteht Items in setaus:
5.578 (2.53)
MIC-U-MA
/16" (8)
4 3/4" (120)
304806
2x 2x
1/
7 3/4" (197,5)
2" (12,5)
3 1/8" (80)
Note: Use always on both sides of girder. Distance between girder hole and girder end 30 mm
1/ " (12) 2
D C B
C in (mm)
7
D in (mm)
Ordering designation
Item no.
Package contents
MI-90/MI-120 2 16 6 2 (75165) 7 8 (200) 11 (280) 13.867(6.29) MIC-SA-MA 304815 MI-90/MI-120 6 129 1 4 (165235) 111316 (300) 13 34 (350) 17.064(7.74) MIC-SB-MA 304816 MI-90/MI-120 914111316 (235300) 13 34 (350) 161516 (430) 20.723(9.40) MIC-SC-MA 304817
Set besteht Items in setaus:
4 2 2
6 1/8" (155) 3 15/16" (100)
9
1/
/16" (14)
5/
16" (8)
4.497 (2.04)
MIC-CU-MA
304828
4
3 1/8" (80)
1/ " (12,5) 2
1
3 15/16" (100)
/4" (6)
page 11
8 11/16" (220)
3 1/8" (80)
S235 JRG2 (DIN 10025), ASTM A570 (36) Hot-dip galvanized 2.2 mils (55 m) DIN EN ISO 1461, ASTM A153
D C B
5 7/8" (150)
1/ 2" (12)
C in (mm)
7
D in (mm)
Ordering designation
Item no.
Package contents
MI-90/MI-120 2 16 6 2 (75165) 7 8 (200) 11 (280) MI-90/MI-120 6 12 9 14 (165235) 11 1316 (300) 13 34 (350) MI-90/MI-120 9 14 11 1316 (235300) 13 34 (350) 16 1516 (430) MI-90/MI-120 For connection to concrete
2 2 2 2
6 1/8" (155)
9
/16" (14)
/16" (15)
page 12
9 1/16" (230)
6 1/8" (156)
8 11/16" (220)
S235 JRG2 (DIN 10025), ASTM A570 (36) None (primer coating-basic connector)
Pos. 1
Flexy pack connector for welding as desired, without connecting parts Parts list
Ordering designation Item no. Info Position
Pos. 2
Pos.1 Pos.2
5 1/2" (140)
5 1/2" (140)
MI- 90 MI-120
MIC-SC90 MIC-SC120
304824 304808
2 2
2 13/16" (72)
2 13/16" (72)
4" (101)
2 13/16" (72)
page 13
Technical data for the clamping system Material: S235 JRG2 (DIN 10025), ASTM A570 (36) Galvanizing: Hot-dip galvanized 2.2 mils (55 m) DIN EN ISO 1461, ASTM A153 Connecting screws: M12 (connection to MI-girder)
2.778 (1.26) 5.688 (2.58) 3.042 (1.38) 2.734 (1.24) 2.998 (1.36)
10* 2 10* 6* 6*
1 15/16" (49) 15
3/ " (400) 4
7"
7, (17
5)
1 /2
3) " (1
9/ " (15) 16
3 9/16" (90)
1 15/16" (49)
1 15/16" (49)
2x
2x
1 " (26) x 9/16" (13,5)
3 9/16" (90)
2x
2x
2x
3 9/16" (90) 3 9/16" (90)
3 3/4" (96)
1x
2x
2x
2x
2x
page 14
4* 4* 10* 10*
4 " (102) 1
3/ " (45) 4
1 5 1/8" (130)
1/ " (12) 2 3/ " (45) 4
1/ " (13) 2
1/
2" (13)
4 " (102)
3/ " (4) 16
4 " (102)
1/ 4" (6)
/2" (12)
5 1/8" (130)
1 3/16" (30)
5/ " (16) 8
5 1/8" (130)
1 3/16" (30)
11/ 16" (18)
3 9/16" (90)
2 15/16" (75)
3/ 16" (5)
1 9/16" (40)
MI-90/MI-120
0.220 (0.1)
MIC-PG
304842
10
5/ 16" (8)
page 15
Technical data for the clamping system Material: S235 JRG2 (DIN EN 10 025), ASTM A570 (36) Galvanizing: Hot-dip galvanized 1.8 mils (45 m)
4 " (102)
1/ " (M12) 2
4 " (102)
1/ " (M12) 2
MI-90 MI-120
*Number of pairs in package
MIA-B090-M12 MIA-B0120-M12
304840 304841
8* 8*
4 15/16" (126)
6 1/8" (156)
MI-90/MI-120
0.044 (0.02)
100
M12-F-SL WS 34
382897
Advantages Self-locking function through stainless steel insert Useable up to 5 times Wrench size 3 4" (19 mm)
/2 (13)
15
/16 (24)
/2 (M12)
3
/4 (19)
page 16
Advantages Easy installation of standard weld-on tabs, e.g. for spring hangers.
S235 JRG2 (DIN EN 10 025), ASTM A570 (36) U-bolt galvanized 1.8 mils (45 m), plate with primer finish
Ordering designation
Item no.
Package contents
MI-90 MI-120
MIC-SPH-90 MIC-SPH-120
304843 283592
2
3/ " (60) 8
4 4
5 1/8" (130) 2
1/ " (M12) 2 3/ 8" (60)
5 1 /8 " (130)
1/ " (M12) 2
1/ " 2
(12)
1/ " (12) 2
3 9/16" (90)
4 3/4" (120)
page 17
EN-GJMW-400-5 (DIN EN 1562), malleable cast iron 8.8 grade 8 grade DIN 1661, self locking 1.8 mils (45 m)
Ordering designation
Item no.
Packege contents
MI-90 MI-120 MI-90 MI-120 MI-90, MI-120 MI-90, MI-120 MI-90, MI-120 MI-90, MI-120 MI-90, MI-120 MI-90, MI-120
0.353 (0.16) 0.419 (0.19) 0.220 (0.10) 0.287 (0.13) 0.617 (0.28) 0.044 (0.02) 0.132 (0.06) 0.220 (0.10) 0.243 (0.11) 0.011 (0.005)
1 7/16" (36,6)
1 7/16" (36,6)
MIA-EH90 MIA-EH120 MIA-OH90 MIA-OH120 MIA-EH-P M12-F-SL WS 34 MIA-TP Hex.head screw M12i120-F/8.8 Hex.head screw M12i130-F/8.8 A 13-F washer
304887 304888 304889 304890 304891 382897 305707 283595 283596 304771
10 10 10 10 10 100 20 40 40 100
/2" (M12)
1/
2" (M12)
3 3/4" (95)
5" (127)
1/
2" (M12) 1/
2. 2-3x 1.
2 13/16" (72)
2" (M12)
/2 (13)
15
/16 (24)
/2 (M12)
3
/4 (19)
1 15/16" (50)
1/ 2" (12,2)
x 1/2" (12,2)
1/ 4" (7)
1. 2.
1 7/16" (36,6)
1 7/16" (36,6)
page 18
Advantages Ends of girder closed securely. With built-in opening to permit drainage of liquids.
Weight lb (kg)
Ordering designation
Item no.
Package contents
3/4" (18,5)
MI-90 MI-120
MIA-EC-90 MIC-EC-120
304892 304893
25 25
3 3/4" (96) 3 3/4" (96)
3/4"
(18.5)
page 19
Note The screw must be positioned against the flange of the steel beam and the wider side of the beam clamp on the base plate of the MI connector Beam clamps must always be used in pairs
MI-90/MI-120
0.772 (0.35)
16
MI-SGC M12
233859 Advantages For steel beams with flange thicknesses from 1 8" to 1 716" (3 to 36 mm) and angle of up to 15 Corrosion protection of steel beam is not damaged by beam clamp Beam clamp is equipped with self-locking nut
1/ 2" (M12)
Items in set :
1x
1 3/16" (30)
1/ " (M12) 2
page 20
MI / MQ connector
Advantages Direct connection to components of the Hilti MQ system. Keyed hold for optimum transmission of forces and moments.
S235 JRG2 (DIN 10025), ASTM A570 (36) Hot-dip galvanized 2.2 mils (55 m) DIN EN ISO 1461, ASTM A153
3/ 16"
MIC-MI/MQ-X MIC-MI/MQ-M8
304881 304882
16 5
9 13/16" (250)
4x
2x
2x
1 5/8" (41)
2.
M8x16
1/
2" (12) 3
/16" (5)
1.
Description
Size
Ordering designation
Item no.
Magnetic wrench
SW 13
MQZ-SVS
Package contents
369693
7 7/8" (200)
page 21
Hilti MI-DGC Beam clamp for direct connection of MI girder to steel beam
Technical data Material: Galvanizing: U-bolt: Malleable cast iron Hot-dip galvanized 2.2 mils (55 m) DIN EN ISO 1461, ASTM A153 M12, 8.8 grade
Note The U-bolt must be positioned against the flange of the steel beam Beam clamps must always be used in pairs
MI-90 MI-120
4 4
233860 233861 Advantages For steel beams with flange thicknesses from 1 8" to 1 7 16" (3 to 36 mm) and angle of up to 15 Corrosion protection of steel beam is not damaged by beam clamp Beam clamp is equipped with self-locking nuts
Items in set :
2x
2x
5 3/16" (131)
1x
Items in set :
1x
2x
2x
1x
1x
page 22
Advantages Easy to install single-handed installation! Opposite side of MI girder still usable for other applications Connector can be used on top or bottom of MI girder With MI-90 13 16" (30 mm) height adjustability (MI-120 9 16" (15 mm) MQ channel fits between MIC-TRC and MI girder
2 2 2
Items in set :
1x 1x 1x 1x
Items in set :
215/16 (75)
1x 1x
1x 1x 1x
Items in set :
1x 1x
1x
1x 1x 1x
1x 1x
page 23
Pos. 3
Pos. 5
Pos. 4
Parts list
Quantity Ordering designation Item no. Info Position
2 2 2 4 6
Cantilever connectors
Self-locking nuts
1 1 4 8
To suit beam size Size as (1) M12-F threaded rod Self-locking nuts
Pos. 2
page 24
2 8 4 12 4
MI-90 MIC-UB90-M12 Hex.head screw M12 i 120F/ 8.8 M12-F hex. collar nut AM 12-F
Pos. 4
Beam height greater than 12 58 (320 mm). Further connections using MIC-90-L cantilever connector.
Parts list
Quantity Ordering designation Item no. Info Position
Pos. 1
Pos. 4 Pos. 5
1 4 4 4 4
MIB-SA MIA-EH-P A13-F M12 i130F/8.8 hex screw M12 hex. collar nut
Self-locking nut
Pos. 3
page 25
Hilti System MQ
Channel installation hot-dip galvanised
Rust ?
No, not with the Hilti rapid installation system.
Extreme convenience during assembly and a high level of safety characterize Hilti's proven MQ channel installation system. This flexible modular system permits optimized protection against corrosion combined with the benefits of rapid channel assembly.
Features of Hilti installation system: Simple selection of the ideal channel for an application. High strength and stability of a structure. Installation safety and simple working principle of the system. Easy and accurately positioned fitting of channels with the single-part, pre-connectable, rapid-installation pushbutton. Quick and easy connection of various channels thanks to total system modularity.
As a pioneer of fastening technology, Hilti is committed to continually improving the products through in-house research and development. An actual example is the MQ system in various materials hot-dip galvanised, HDG plus and stainless steel.
When selecting a suitable system, allowance must be made for the conditions it will be used in. As a guide, the following general recommendations can be given for selecting the right use of materials and types of protection against corrosion:
Outside
Inside
Anchors made of stainless steel are recommended for fastening hot-dip galvanized-, HDG plus- and stainless-steel components. Please contact our advisory engineers for further details.
page 26
Technical data
Definition of axes
F F
e2 e1
"open"
e1
y-axis
1 5/8"
1 5/8"
1 5/8"
e2
z-axis
Channel wall thickness t [ga] Cross-sectional area A [in2] Channel weight [Ib/ft] Delivered length [ft] Galvanising Cont. hot-dip galvanised (HDG plus), 2.8 mil Cross-section values Y-axis Axis of gravity "open" 1) e1 [in] Axis of gravity e2 [in] Moment of inertia Iy [in4] Section modulus Sy2 [in3] Radius of gyration Ry [cm] Z-axis Moment of inertia Iz [in4] Section modulus Sz [in3] Radius of gyration Rz [in]
1)
The smaller value (Wy1, Wy2) is decisive for the calculated bending dimension (Wy1 = Iy/e1 or Wy2 = Iy/e2).
Definition of axes
2
F F
e2 e1
"open"
e1
y-axis
e2
z-axis
41.3
41.3
41.3
Channel wall thickness t [mm] Cross-sectional area A [mm2] Channel weight [kg/m] Delivered length [m] Galvanising Cont. hot-dip galvanised (HDG plus), 70 m Cross-section values Y-axis Axis of gravity "open" 1) e1 [mm] Axis of gravity e2 [mm] Moment of inertia Iy [cm4] Section modulus Sy2 [cm3] Radius of gyration Ry [cm] Z-axis Moment of inertia Iz [cm4] Section modulus Sz [cm3] Radius of gyration Rz [cm]
1)
The smaller value (Wy1, Wy2) is decisive for the calculated bending dimension (Wy1 = Iy/e1 or Wy2 = Iy/e2).
page 28
Technical data
Definition of axes
F F
e2 e1
"open"
e1
y-axis
e2
z-axis
12ga
1 5/8"
Channel wall thickness t [ga] Cross-sectional area A [in 2] Channel weight [lb/ft] Delivered lenght [ft] Galvanising Hot-dip galvanised, coating thickness [mil] Cross-section values Y-axis Axis of gravity "open" 1) e1 [in] Axis of gravity e2 [in] Moment of inertia Iy [in 4] Section modulus Sy2 [in3] Radius of gyration Ry [in] Z-axis Moment of inertia Iz [in 4] Section modulus S z [in 3] Radius of gyration Rz [in]
1)
13/16"
The smaller value (Wy1, Wy2) is decisive for the calculated bending dimension (Wy1 = Iy/e1 or Wy2 = Iy/e2).
Definition of axes
3
F F
2.5
"open"
z-axis
20.6
e1
e2
41.3
41.3
y-axis
2.5
e2
e1
41.3
41.3
82.6
41.3
Channel wall thickness t [mm] Cross-sectional area A [mm2] Channel weight [kg/m] Delivered lenght [m] Galvanising Hot-dip galvanised, coating thickness [m] Cross-section values Y-axis Axis of gravity "open" 1) e1 [mm] Axis of gravity e2 [mm] Moment of inertia Iy [cm4] Section modulus Wy2 [cm3] Radius of gyration iy [cm] Z-axis Moment of inertia Iz [cm4] Section modulus Wz [cm3] Radius of gyration iz [cm]
1)
The smaller value (Wy1, Wy2) is decisive for the calculated bending dimension (Wy1 = Iy/e1 or Wy2 = Iy/e2).
124
2.5
page 29
Installation channels
Features: Serrated C-section. Installation assisted by dimension marking. Great flexibility due to slots. Aesthetic appearance. Swage-joined double channel. Technical data: Material: MQ 124XD-F: S250 GD (DIN EN 10326), ASTM A653 Grade 33 MS41D-F: S275JR (DIN EN 10025), SAE 1016 HS1316-12/HDG, HS158-12/HDG: S235JR (DIN EN 10025), ASTM A283 (C) MQ HDG plus channels: S250 GD (DIN EN 10326), ASTM A653, Grade 33 Galvanising: MQ 124XD-F: hot-dip galvanised, 2.6 mil (65 m), DIN EN ISO 1461, ASTM A123 MS41D-F: hot-dip galvanised, 2.2 mil (55 m), DIN EN ISO 1461 HS 1316-12/HDG, HS158-12/HDG: hot-dip galvanised, 2.6 mil (65 m), ASTM A 123 MQ HDG plus channels: continuous hot-dip galvanised, 2.8 mil (70 m), DIN EN 10326 z1000, ASTM A653 G300
Single channels
Hot dipped galvanised
Channel height in (mm) Length ft (m) Metal thickness gauge (mm) Weight Ib/ft (kg/m) Ordering designation Item no.
4" (100)
14ga (2mm)
2 1/2" x 9/16" (63 x 13.5)
1 5/8" (41.3)
7
4" (100)
12ga (2.5)
12ga (2.5)
1 5/8" (41.3)
5
/16" (20.6)
5 7
/16" (7.5)
/16" (7.5)
/8" (22.3) 1
5/ 8" (41.3)
/8" (22.3)
5/ " (7.5) 16
/16" (7.5)
1 /8" (41.3)
15/8 (41) 20 (6) 3 14 (82) 20 (6) 4 7/8 (124) 20 (6) 3 14 (82) 10 (3)
3" (75)
11ga (3mm)
3" (75)
1 5/8" (41.2)
5 7
3 1/4" (82.6)
3 1/4" (82.6)
1 9/16" x 9/16" (40 x 13.5)
5
4 7/8" (124)
7
/8" (22.3)
/16" (7.5)
7
/16" (7.5)
/8" (22.3)
5/
/16" (7.5)
1 5/8" (41.3)
8" (41.3)
page 30
Brackets
Features: Serrated C-section. Installation assisted by dimension marking. Great flexibility due to slots. Double-channel brackets welded all around.
S 235 JR (DIN EN 10025), ASTM A283 (C) hot-dip galvanised, min. 2.2 mil (56 m)
Brackets (HDG)
Strut length in (mm) Metal thickness gauge (mm) Weight each lb (g) Packaging contents (pcs) Ordering designation Item no.
11 7/16" (450)
13
/4" (6)
17-1116" (450) 11-1316" (300) 23- 58" (600) 39- 38" (1000) 39- 38" (1000)
1.96 (890) 2.09 (950) 3.46 (1570) 5.29 (2400) 11.20 (5080)
10 10 10 10 6
3 1/8" (80)
4 15/16" (125)
1 15/16" (50)
13
/4" (6)
3 1/8" (80)
4 15/16" (125)
39 3/8" (1000)
13
/8" (10)
4 3/4" (120)
6 1/2" (165)
2 3/8" (60)
2 15/16" (74)
L
7
/16" (11)
Ordering desigation
Item no.
45
10
MQK-SK-F
304129
H
1 5/16" (33)
/16" (13.5)
page 31
Channel nut
Features: Simple, compact, time saving. Single part which can be prefitted. Easy to use. Universal: one and the same nut for all channels.
Pushbutton (HDG)
Bolt: M10 material 8.8 as per DIN ISO 898 Width across flats: 1116" (17 mm) Nut: C4C as per DIN EN 10 263 Plate: S 235 JR (DIN EN 10025), ASTM A283 (C)
Connection thread Weight each lb (g) Packaging contents (pcs) Outside packaging contents (pcs) Ordering desigation Item no.
M10
0.185 (84) 25
Rec. tensile load, Zrec Ibf (kN) Channel II Channel I/III
200
Rec. shear load, Qrec lbf (kN) Channel I Channel II
MQN-F
304130
Tightening torque, M D lbf ft (Nm)
Item
Channel III
1100 (5.0) 1800 (8.0) 400 (1.8)1) 1000 (4.5)2) 670 (3.0)3) HS1316-12/HDG, HS 158-12/HDG, MS-41-D-F
MQ-21-HDG plus, MQ-41-HDG plus, MQ-21D-HDG plus, MQ-41D-HDG plus
30 (40)
MQ-124XD-F
Shear loading applies to single fastening. Qrec 670 lbf (3.0 kN) for two fastenings Shear loading applies to single fastening. Qrec 1800 lbf (8.0 kN) for two fastenings Shear loading applies to single fastening. Qrec 1100 lbf (5.0 kN) for two fastenings
0.09 (40) 0.08 (38) 0.08 (38) 0.08 (38) 0.08 (38)
Rec. tensile load, Zrec Ibf (kN)
25 25 25 25 25
Item
Channel II
Channel I/III
Channel III
MQM-M 8-F MQM-M10-F MQM-M12-F MQM-F 38"-F MQM-F 12"-F Channel I: Channel II: Channel III:
page 32
1100 (5.0) 1100 (5.0) 400 (1.8) 800 (3.5) 1100 (5.0) 1800 (8.0) 400 (1.8) 1000 (4.5) 1100 (5.0) 1800 (8.0) 400 (1.8) 1000 (4.5) 1100 (5.0) 1800 (8.0) 400 (1.8) 1000 (4.5) 1100 (5.0) 1800 (8.0) 400 (1.8) 1000 (4.5) HS1316-12/HDG, HS 158-12/HDG, MS-41-D-F MQ-124XD-F
450 (2.0) 670 (3.0) 670 (3.0) 670 (3.0) 670 (3.0)
1 5
EN-GJMW-450-7 as per DIN EN 1562 S 235 JR (DIN EN 10025), ASTM A283 (C) PB
Weight each Ib (g) Packaging contents (pcs) Outside packaging contents (pcs) Ordering designation Item no.
0.165 (75) 0.161 (72) 0.157 (72) 0.181 (82) 0.192 (87) 0.183 (83) 0.185 (84)
25 25 25 25 25 25 25
MQA-M 8-F MQA-M10-F MQA-M12-F MQA-M16-F MQA-F 3 8"-F MQA-F 1 2"-F MQA-F 5 8"-F
Item
MQA M8-F MQA M10-F MQA M12-F MQA M16-F MQA-F 38"-F MQA-F 12"-F MQA-F 58"-F Channel I: Channel II: Channel III:
670 (3.0) 670 (3.0) 1100 (5.0) 1100 (5.0) 1100 (5.0) 1800 (8.0) 1100 (5.0) 1800 (8.0) 1100 (5.0) 1100 (8.0) 1100 (5.0) 1800 (8.0) 1100 (5.0) 1800 (8.0) HS1316-12/HDG, HS 158-12/HDG, MS-41-D-F MQ-124XD-F
page 33
/4" (19.4)
/4" (19)
1 3/8" (35)
/8" (10)
S 235 JR (DIN EN 10025), ASTM A283 (C) 3 16" (4 mm) hot-dip galvanised, min. 2.2 mil (56 m), DIN EN ISO 1461, ASTM A153
90 angle (HDG)
Weight each lg (g) Packaging contents (pcs) Ordering designation Item no.
20 10 20
4 /8" (105)
2 3/8" (61)
2 3/8" (61)
2 3/8" (61)
4 3/8" (111)
7 7/8" (198)
2.601 (1180)
10
MQW-S/2-F
304181
9/
16" (13.5)
6 1/2" (167)
6 1/2" (167)
10 10
MQV-2/2D-F MQV-3/2D-F
304150 304152
4 7/16" (112)
4 7/16" (112)
10 10
MQV-12-F MQV-P4-F
304155 304156
8 1/16" (205)
page 34
/4" (19.4)
/4" (19)
1 3/8" (35)
/8" (10)
Technical data: Material: S 235 JR (DIN EN 10025), ASTM A283 (C) Galvanising: hot-dip galvanised, min. 2.2 mil (56 m) Separate design verification of the fastening on the base material must be provided.
10 20
MQV-2/2D-14-F MQP-1/1-F
Bolt (A) Pushbutton
304151 304161
4 7/16" (112)
Frec
Item
Channel (B)
MQV-2/2D-14-F
Double Double
MQN-F MQN-F
40 (30) 40 (30)
4 1/8" (105)
0.722 (350)
10
MQP-45-F
304164
9
45
/16" (14) 1 5/8" (41) 1 5/8" (42)
A
13
4 1/8" (105)
12 8 6
Bolt (A)
Frec
3 1/8" (80)
Item
Channel II
4 3/16" (106)
1100 (5.0) 1800 (8.0) Double 1700 (7.5) 2500 (11.0) Quadruple 1700 (7.5) 2500 (11.0) Quadruple HS 1316-12/HDG, HS 158-12/HDG MQ-41D-HDG plus MQ-124XD-F
Frec
3 15/16" (100)
A
5 1/8" (130)
13
Frec
3 15/16" (100)
9 13/16" (250)
page 35
Beam clamp
Features: For connecting installation channels to steel beams without drilling or welding. The clamp set fits all standard T-beams (max. clamping thickness 7 8" (23 mm).
M8
3 3/8" (92) 2 3/8" (60) 3 3/4" (95)
3
/16" (5)
MQ21, MQ41, MQ21D, HS13/16, HS15/8 MQ41D, MS41D MQ41D, MS41D, MQ124X D
10 10 10
M10
1
3 /8" (92)
/4" (6)
Beam clamp
3 9/16" (90)
MQT-21-41-F 7 (10) MQT-41-82-F 15 (20) MQT-82-124-F 22 (30) Always use beam clamps in pairs. Channel loading values must be allowed for.
5 1/2" (140)
3 3/8" (92)
/16" (8)
3 3/8" (85)
7 1/16" (178)
1 5/16" (33.5)
13
/16" (20)
Ordering designation
Item no.
max . cla mp ick ing th
ness
7/
8"
(23)
MQ-21, MQ-41
8 (10)
80.573 (260)
48
MQT-C23-F 304195
M12
/8" (10) 1 9/16" (40)
Beam clamp
MQT-C23-F 30 (40) Always use beam clamps in pairs. Channel loading values must be allowed for.
560 (2.5)
page 36
Clamp
Features: Universal: few parts for all applications. Easy to use. The MQN-F pushbutton can be prefitted.
/4" (19.4)
/4" (19)
1 3/8" (35)
/8" (10)
S 235 JR (DIN EN 10025), ASTM A283 (C) 3 16" (4 mm) hot-dip galvanised, min. 2.2 mils (56 m), DIN EN ISO 1461, ASTM A153
Clamps (HDG)
Suitable for channel height Weight each lb (g) Packaging contents (pcs) Ordering designation Item no.
10 10
MQB-41-F MQB-G41-F
304183 304189
page 37
Accessories
Features: Matching items in programme.
hot-dip galvanised, min. 2.2 mils (56 m), DIN EN ISO 1461, ASTM A153
1 13/16" (45.5)
3/ " (5) 16
2 1/16" (52.5)
3/ 7/ 1/ 9/
8"
(9.5)
0.203 (92) 0.194 (88) 0.185 (84) 0.194 (88) 0.185 (84) 0.176 (80)
20 20 20 20 20 20
Channel endcap
Made of polypropylene (PP), suitable for all installation channels.
Suitable for channel height Weight each lb (g) Packaging contents (pcs.) Ordering designation Item no.
50 50
MQZ-E21 MQZ-E41
370598 369685
1 5/8" (41.3)
page 38
System MQ channel installation stainless Schienenmontage System MQ Edelstahl steel Channel installation
Hilti System MQ
stainless steel
No more rusting !
Hilti. Outperform. Outlast.
page 39
Rust ?
No, not with the Hilti rapid installation system.
Extreme convenience during assembly and a high level of safety characterize Hilti's proven MQ channel installation system. This flexible modular system permits optimized protection against corrosion combined with the benefits of rapid channel assembly.
Features of Hilti installation system: Simple selection of the ideal channel for an application. High strength and stability of a structure. Installation safety and simple working principle of the system. Easy and accurately positioned fitting of channels with the single-part, pre-connectable, rapid-installation pushbutton. Quick and easy connection of various channels thanks to total system modularity.
As a pioneer of fastening technology, Hilti is committed to continually improving the products through in-house research and development. An actual example is the MQ system in various materials hot-dip galvanised, HDG plus and stainless steel.
When selecting a suitable system, allowance must be made for the conditions it will be used in. As a guide, the following general recommendations can be given for selecting the right use of materials and types of protection against corrosion:
Outside
Inside
Anchors made of stainless steel are recommended for fastening hot-dip galvanized-, HDG plus- and stainless-steel components. Please contact our advisory engineers for further details.
page 40
Technical data
Definition of axes
F F
e2 e1
"open"
e1
y-axis
13/16"
e2
z-axis
1 5/8"
1 5/8"
13/16"
1 5/8"
Channel wall thickness Cross-sectional area Channel weight Delivered length Material Stainless steel 316Ti / 316L Cross-section values Y-axis Axis of gravity "open" 1) Axis of gravity Moment of inertia Section modulus Radius of gyration Z-axis Moment of inertia Section modulus Radius of gyration
1)
The smaller value (Wy1, Wy2) is decisive for the calculated bending dimension (Wy1 = Iy/e1 or Wy2 = Iy/e2).
Definition of axes
2.5
F F
y-axis
e1
"open"
e2
z-axis
20.6
41.3
41.3
20.6
e2
41.3
Channel wall thickness Cross-sectional area Channel weight Delivered length Material Stainless steel 1.4571/1.4404 Cross-section values Y-axis Axis of gravity "open" 1) Axis of gravity Moment of inertia Section modulus Radius of gyration Z-axis Moment of inertia Section modulus Radius of gyration
1)
41.3
e1
The smaller value (Wy1, Wy2) is decisive for the calculated bending dimension (Wy1 = Iy/e1 or Wy2 = Iy/e2).
page 41
Installation channels
Features: Serrated C-section. Installation assisted by dimension marking. Great flexibility due to slots. Aesthetic appearance. Double channels laser welded along both sides.
Single channels
Channel height lb (mm) Length ft (m) Metal thickness (mm)
Stainless steel
13
4" (100)
14ga (2mm)
2 1/2" x 9/16" (63 x 13.5)
5
Ordering designation
Item no.
/16" (20.6)
7
1316 (21) 1316 (21) 158 (41) 158 (41) 1316 (21) 158 (41)
0.988 (1.47) 0.988 (1.47) 1.425 (2.12) 1.425 (2.12) 1.287 (1.88) 1.881 (2.69)
/16" (7.5)
14ga (2mm)
1 5/8" (41.3)
7
4" (100)
/8" (22.3)
/16" (7.5)
1 5/8" (41.3)
12ga (2.5)
16" (7.5)
1 /8" (41.3)
12ga (2.5)
5/
8" (41.3) 7/
8" (22.3)
5/ " (7.5) 16
1 /8" (41.3)
Double channels
Channel height lb (mm) Length ft (m) Metal thickness (mm)
Stainless steel
Ordering designation
Item no.
3 1/4" (82.6)
/16" (7.5)
3 1/4" (82.6)
/8" (22.3)
/16" (7.5)
1 5/8" (41.3)
page 42
Brackets
Features: Serrated C-section. Installation assisted by dimension marking. Great flexibility due to slots. Double-channel brackets welded all around.
Brackets
Channel length lb (mm) Metal thickness gauge lb (mm) Weight each lb (g) Packaging conctents (pcs) Ordering designation Item no.
13
/4" (6)
14 (2) 14 (2)
8 4
MQK-41/600-R MQK-41D/750-R
304007 304009
1 15/16" (50)
3 1/8" (80)
4 15/16" (125)
13
/8" (10)
4 3/4" (120)
6 1/2" (165)
2 3/8" (60)
Angle brace
Stainless steel
L
2 15/16" (74)
For fabricating wall brackets with individual stand-off lengths. Material: Material thickness:
A in (mm)
/16" (11)
MQK-SL-R 304010
/16" (13.5)
page 43
Channel nut
Features: Simple, compact, time saving. Single part which can be prefitted. Easy to use. Universal: one and the same nut for all channels.
Stainless steel
Pushbutton
Bolt: Width across flats: Nut: Plate:
Connection thread
Stainless steel
M10 material A4-70 as per DIN EN ISO 3506-1 (1116") 17 mm 1.4581 as per DIN EN 10 283 1.4401 (A4) as per DIN 17 440
Weight each lb (g) Packaging contents (pcs) Outside packaging contents (pcs) Ordering designation Item no.
M10
Item
0.170 (77) 25
Rec. tensile load, Zrec Ibf (kN) Channel I Channel II
200
Rec. shear load, Qrec lbf (kN)
MQN-R
Tightening torque M D lbf ft (Nm)
304012
1100 (5.0) 1800 (8.0) 1100 (5.0) 1) 30 (40) MQ-21, MQ-41, MQ-21D, MQ-41D (stainless steel) MS21, MS41, MS41D
Shear loading applies to single fastening. Qrec lbf (kN) 1980(9.0) for two fastenings
Wing nut
Nut, M6M12: Plastic:
Connection thread
Stainless steel
3 1 1
0.06 (29) 0.06 (27) 0.05 (25) 0.05 (23) 0.05 (25) 0.05 (23)
Rec. tensile load, Zrec Ibf (kN) Channel I
25 25 25 25 25 25
Channel II
MQM-M 6-R MQM-M 8-R MQM-M10-R MQM-M12-R MQM-F 38"-R MQM-F 12"-R Channel I: Channel II:
page 44
670 (3.0) 670 (3.0) 340 (1.5) 1100 (5.0) 1100 (5.0) 800 (3.5) 1100 (5.0) 1800 (8.0) 1100 (5.0) 1100 (5.0) 1800 (8.0) 1100 (5.0) 1100 (5.0) 1800 (8.0) 1100 (5.0) 1100 (5.0) 1800 (8.0) 1100 (5.0) MQ-21, MQ-41, MQ-21D, MQ-41D (stainless steel) MS21, MS41, MS41D (stainless steel)
Stainless steel
Stainless steel
Ordering designation
Item no.
M12
0.157 (71)
Rec. tensile load, Zrec Ibf (kN) Channel I
25
200
MQA-M12-R
Tightening torque M D lbf ft (Nm)
304023
Item
Channel II
1100 (5.0) 1800 (8.0) 23 (31) MQ-21, MQ-41, MQ-21D, MQ-41D (stainless steel) MS21, MS41, MS41D (stainless steel)
page 45
/4" (19.4)
/4" (19)
1 3/8" (35)
/8" (10)
90 angle
Angle, 2 hole, 90 Angle, 8 hole, 90 Angle, 3 hole, 90
Stainless steel
Ordering
10 10 10
4 1/8" (105)
2 3/8" (61)
2 3/8" (61)
2 3/8" (61)
4 3/8" (111)
45 angle
Stainless steel
106 45
Ordering designation
Item no.
56
Angle, 3 hole, 45
0.342 (155)
10
MQW-3/45-R
304053
Compression: Frec. Tension: Frec.
A
(double bolted A )
Angle bracket
Angle bracket, two braces
Stainless steel
Ordering designation
Item no.
7 7/8" (198)
2.601 (1180)
10
MQW-S/2-R
304059
7 7/8" (198) 3 15/16" (100)
9/
16" (13.5)
page 46
Stainless steel
6 1/2" (167)
Ordering designation
Item no.
0.970 (440)
10
MQV-2/2D-R
304032
4 7/16" (112)
Stainless steel
Ordering designation
Item no.
1.224 (555)
10
MQV-12-R
304037
/4" (19.4)
/4" (19)
1 3/8" (35)
/8" (10)
Technical data: Material: Stainless steel, 1.4571 or 1.4404, 316Ti or 316L Separate design verification of the fastening on the base material must be provided.
Stainless steel
Ordering designation
Item no.
Channel
B
MS-41, MQ-21D
F rec lbf (kN)
0.970 (440)
Channel (B)
10
Bolt (A)
MQV-2/2D-14-R
Pushbutton
304033
Tightening torque M D lbf ft (Nm)
4 7/16" (112)
Frec
Item
MQV-2/2D-14-R
1750 (7.8)
MQ-41-R
Double
MQN-R
30 (40)
Channel base
Suitable for channel height
Stainless steel
A
Packaging contents (pcs) Ordering designation Item no.
13
4 1/8" (105)
12 8
MQP-21-72-R MQP-82-R
304047 304048
Frec
3 1/8" (80)
Item
Bolt (A)
Pushbutton
A
13
MQP-21-72-R MQP-82-R
Double Quadruple
MQN-R MQN-R
30 (40) 30 (40)
5
4 3/16" (106)
Frec
7 7/8" (200)
page 47
Beam clamp
Features: For connecting installation channels to steel beams without drilling or welding. The clamp set fits all standard T-beams (max. clamping thickness 78" (23 mm).
Stainless steel
Stainless steel
Ordering designation
Item no.
2 15/16" (75)
10 10
MQT-21-41-R MQT-52-82-R
Max. rec. load lbf (kN)
304067 304068
Beam clamp
MQT-21-41-R 7 (10) MQT-52-82-R 15 (20) Always use beam clamps in pairs. Channel loading values must be allowed for.
2 15/16" (75)
Stainless steel
1 5/16" (33.5)
13
/16" (20)
Ordering designation
Item no.
8 (10)
0.573 (260)
48
MQT-C23-R
304069
max
. cla
mp
ick ing th
ness
7/
8"
(23)
M12
/8" (10) 1 9/16" (40)
Beam clamp
MQT-C23-R 30 (40) Always use beam clamps in pairs. Channel loading values must be allowed for.
560 (2.5)
page 48
Clamp
Features: Universal: few parts for all applications. Easy to use. The MQN-R pushbutton can be prefitted.
/4" (19.4)
/4" (19)
1 3/8" (35)
/8" (10)
Clamps
Suitable for channel height
Stainless steel
Weight each lb (g) Packaging contents (pcs) Ordering designation Item no.
10 10
MQB-41-R MQB-82-R
304061 304063
6 5/16" (161)
4 3/16" (106)
page 49
Accessories
Features: Machting items in programme.
Boss plate
Thread
Stainless steel
1 13/16" (45.5)
2 1/16" (52.5)
Ordering designation
Item no.
3/ " (5) 16
3/ 7/ 1/ 9/
8"
(9.5)
0.203 (92) 0.194 (88) 0.185 (84) 0.194 (88) 0.185 (84)
20 20 20 20 20
Installation washer
Hole diameter (mm) Weight each lb (g)
Stainless steel
Ordering designation
Item no.
/16" (10.5)
7/16 (10.5)
0.066 (30)
40
MQZ-U-R
304084
Channel endcap
Made of polypropylene (PP), suitable for all installation channels.
Suitable for channel height Weight each lb (g) Packaging contents (pcs.) Ordering designation Item no.
50 50
MQZ-E21 MQZ-E41
370598 369685
1 5/8" (41.3)
page 50
page 51
Hilti = registered trademark of Hilti Corp., Schaan | W 3427 0607 5-en | 1 Printed in Liechtenstein | 2007 | Right of technical and programme changes reserved S. E. & O.