Beruflich Dokumente
Kultur Dokumente
The F240, F241 and F244 are octal buffers and line drivers designed to be employed as memory address drivers, clock drivers, and bus-oriented transmitters/receivers which provide improved PC board density. 3-State Outputs Drive Bus Lines or Buffer Memory Address Registers Outputs Sink 64 mA 15 mA Source Current Input Clamp Diodes Limit High-Speed Termination Effects ESD > 4000 Volts
CONNECTION DIAGRAMS
J SUFFIX CERAMIC CASE 732-03
1
MC54/74F240
VCC OEb Ya0 20 19 18 Ib0 17 Ya1 16 Ib1 15 Ya2 14 Ib2 13 Ya3 12 Ib3 11
20
3 Yb0
4 Ia1
5 Yb1
6 Ia2
7 Yb2
8 Ia3
10
OEa Ia0
Yb3 GND
20 1
MC54/74F241
VCC OEb Ya0 20 19 18 Ib0 17 Ya1 16 Ib1 15 Ya2 14 Ib2 13 Ya3 12 Ib3 11
ORDERING INFORMATION
MC54FXXXJ Ceramic MC74FXXXN Plastic MC74FXXXDW SOIC
1 OEa
2 Ia0
3 Yb0
4 Ia1
5 Yb1
6 Ia2
7 Yb2
8 Ia3
9 Yb3
10 GND
MC54/74F244
VCC OEb Ya0 20 19 18 Ib0 17 Ya1 16 Ib1 15 Ya2 14 Ib2 13 Ya3 12 Ib3 11
1 OEa
2 Ia0
3 Yb0
4 Ia1
5 Yb1
6 Ia2
7 Yb2
8 Ia3
10
Yb3 GND
H = HIGH Voltage Level; L = LOW Voltage Level; X = Dont Care; Z = High Impedance
NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable device type. 2. Not more than one output should be shorted at a time, nor for more than 1 second.
AC CHARACTERISTICS MC54/74F240
54/74F TA = +25C VCC = +5.0 V CL = 50 pF Symbol tPLH tPHL tPZH tPZL tPHZ tPLZ Output Disable Time Output Enable Time Parameter Propagation Delay, Data to Output Min 2.5 1.5 2.0 4.0 2.0 1.5 Typ 5.1 3.5 3.5 6.9 4.0 6.0 Max 7.0 4.7 5.2 9.0 5.3 8.0 54F TA = -55C to +125C VCC = 5.0 V 10% CL = 50 pF Min 2.5 1.5 2.0 4.0 2.0 2.0 Max 9.0 6.0 6.5 13.5 6.5 12.5 74F TA = 0C to +70C VCC = 5.0 V 10% CL = 50 pF Min 2.5 1.5 2.0 4.0 2.0 1.5 Max 8.0 5.7 5.7 10 6.3 9.5 ns ns Unit ns
AC CHARACTERISTICS MC54/74F241
54/74F TA = +25C VCC = +5.0 V CL = 50 pF Symbol tPLH tPHL tPZH tPZL tPHZ tPLZ Output Disable Time Output Enable Time Parameter Propagation Delay, Data to Output Min 2.5 2.5 2.0 2.0 2.0 2.0 Typ 4.0 4.0 4.3 5.4 4.5 4.5 Max 5.2 5.2 5.7 7.0 6.0 6.5 54F TA = -55C to +125C VCC = 5.0 V 10% CL = 50 pF Min 2.0 2.0 2.0 2.0 2.0 2.0 Max 6.5 7.0 7.0 8.5 7.0 12.5 74F TA = 0C to +70C VCC = 5.0 V 10% CL = 50 pF Min 2.5 2.5 2.0 2.0 2.0 2.0 Max 6.2 6.5 6.7 8.0 7.0 7.5 ns ns Unit ns
AC CHARACTERISTICS MC54/74F244
54/74F TA = +25C VCC = +5.0 V CL = 50 pF Symbol tPLH tPHL tPZH tPZL tPHZ tPLZ Output Disable Time Output Enable Time Parameter Propagation Delay, Data to Output Min 2.5 2.5 2.0 2.0 2.0 2.0 Typ 4.0 4.0 4.3 5.4 4.5 4.5 Max 5.2 5.2 5.7 7.0 6.0 6.0 54F TA = -55C to +125C VCC = 5.0 V 10% CL = 50 pF Min 2.5 2.5 2.0 2.0 2.0 2.0 Max 6.5 7.0 7.0 8.5 7.0 10.0 74F TA = 0C to +70C VCC = 5.0 V 10% CL = 50 pF Min 2.5 2.5 2.0 2.0 2.0 2.0 Max 6.2 6.5 6.7 8.0 7.0 7.0 ns ns Unit ns
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. 3. CONTROLLING DIMENSION: MILLIMETER. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE.
-B1 10
0.25 (0.010)
5.
10 PL
R X 45 C K
M
-T-
SEATING PLANE
M D 20 PL
0.25 (0.010) T B
S
DIM A B C D F G J K M P R
0.050 BSC 0.010 0.004 0 0.395 0.010 0.012 0.009 7 0.415 0.029
10.05 0.25
20 1
11
2.
10
3.
B A F C L
N H D
SEATING PLANE
J M
DIM A B C D F G H J K L M N
7.62 BSC 0
15
0.300 BSC 0
15
0.25
1.02
0.010
0.040
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. 3. CONTROLLING DIMENSION: INCH. DIMENSION L" TO CENTER OF LEAD WHEN FORMED PARALLEL.
B C L
4.
5.
-TSEATING PLANE
K E G F D 20 PL
0.25 (0.010)
M
M J 20 PL
0.25 (0.010) T A
M M
DIM A B C D E F G J K L M N
7.62 BSC 0
15
0.300 BSC 0
15
0.51
1.01
0.020
0.040
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters can and do vary in different applications. All operating parameters, including Typicals must be validated for each customer application by customers technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
Literature Distribution Centers: USA: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. EUROPE: Motorola Ltd.; European Literature Centre; 88 Tanners Drive, Blakelands, Milton Keynes, MK14 5BP, England. JAPAN: Nippon Motorola Ltd.; 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. ASIA PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Center, No. 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong.