Beruflich Dokumente
Kultur Dokumente
1)
Chapter 5 With 100% Accurate Answers
1. In what two ways does SDM differ from the IOS CLI? (Choose two.)
**SDM is used for in-band management only. The IOS CLI can be used for in-
band and out-of-band management.
SDM is accessed through a Telnet application. The IOS CLI is accessed through
a web browser.
SDM is available for all router platforms. The IOS CLI is available for a limited
number of Cisco devices.
**SDM utilizes GUI buttons and text boxes. The IOS CLI requires the use of
text-based commands.
SDM is used for advanced configuration tasks. The IOS CLI is preferred for
initial basic device configuration.
5. How does the SYST LED on the catalyst 2960 switch indicate a POST
failure?
6. Refer to the exhibit. A company always uses the last valid IP address in a
subnetwork as the IP address of the router LAN interface. A network
administrator is using a laptop to configure switch X with a default
gateway. Assuming that the switch IP address is 192.168.5.147/24, what
command will the administrator use to assign a default gateway to the
switch?
8. Passwords can be used to restrict access to all or parts of the Cisco IOS.
Cisco-Training.net
Select the modes and interfaces that can be protected with passwords.
(Choose three.)
**VTY interface
**console interface
Ethernet interface
secret EXEC mode
**privileged EXEC mode
router configuration mode
**Tab
Ctrl-P
Ctrl-N
Up Arrow
Right Arrow
Down Arrow
10. What is the correct command sequence to configure a router host name
to 'LAB_A'?
**Router> enable
Router# configure terminal
Router(config)# hostname LAB_A
Router> enable
Router# hostname LAB_A
Router> enable
Router# configure router
Router(config)# hostname LAB_A
Router> enable
Router(config)# host name LAB_A
11. Refer to the exhibit. From the router console, an administrator is unable
to ping a Catalyst switch that is located in another building. What can the
administrator do from her location to check the IP configuration of the
attached switch?
12. Which two options must be selected in SDM Express to enable a router
serial interface to obtain an IP address automatically? (Choose two.)
13. What three settings can be made in the SDM Express basic
configuration screen? (Choose three.)
**host name
DHCP options
**domain name
interface IP addresses
**enable secret password
DNS server IP addresses
15. What option within Cisco SDM Express must be configured to allow
hosts that receive IP address settings from the router to resolve names on
the network or Internet?
**host name
domain name
DHCP address pool
**DNS server IP address
Cisco-Training.net
16. Which three encapsulation types can be set on a serial interface by an
administrator who is using SDM Express? (Choose three.)
ATM
CHAP
**Frame Relay
**HDLC
PAP
**PPP
17. Which command will display routing table information about all known
networks and subnetworks?
console
AUX
**Telnet
modem
**platform
routing protocol
**connected interface of neighbor device
**device ID
IP addresses of all interfaces
enable mode password
Cisco-Training.net
transmission of data
reception of data
**clocking for the synchronous link
noise cancellation in transmitted data
22. Refer to the exhibit. Which series of commands will enable users who
are attached to Router1 to access the remote server?
The host is configured in a different subnet from the subnet of the switch.
**There is a duplex mismatch between the workstation and switch port.
The switch port is running at a different speed from the speed of the workstation
NIC.
Cisco-Training.net
The host has been configured with a default gateway that is different from that
of the switch.
24. Which of the following statements are true regarding the user EXEC
mode? (Choose two.)
Router(config-if)# enable
Router(config-if)# no down
Router(config-if)# s0 active
Router(config-if)# interface up
**Router(config-if)# no shutdown
Cisco-Training.net