Sie sind auf Seite 1von 1

PRODUCT DATA SHEET CERAM-KOTE 54 SF With biocide crystals against SRB Immersion Service up to 150oC

PRODUCT DESCRIPTION: CERAM-KOTE 54 SF (Saudi ARAMCO Approved under: APCS-2i, APCS-28 and APCS-117) a two pack ceramic composite Novolac Lining providing chemical resistance, corrosion and abrasion protection to a wide variety of metal, fibreglass, reinforced plastic and concrete substrates in extremely aggressive environments . TECHNICAL INFORMATION: Colour: Volume Solids: VOC: Flexibility: Surface: Chemical resistance Abrasion resistance: Adhesion: Specific Gravity (Mix):

Light Grey, Dark Grey 100% (ASTM D2697) 0 mg Excellent Mat Excellent see Resistance List Good Excellent 1.55 (ASTM D1475)

Application range: Typical Film thickness per coat Theoretical consumption kg/m2 Theoretical Consumption L/m2 Dry Wet 1000m 1000m 1.55 1.00 Number of Coats: One or two coats - depending on environment. Minimum coating thickness 400m. Maximum thickness per layer: 700m. Contact CERAM-KOTE INTERNATIONAL technical services for specific system and application advice. APPLICATION DATA: Application methods: Airless spray pump (without filter), Ratio 1:68 or greater. Tip size: 0.019-0.029. Hose length max. 50m Spray hose diameter max. ; Material must be taken up directly (without intake hose); avoid waiting time under pressure (reduction of pot life!). Spray gun 6-7bar, trowel or rake application. 10 Parts A (base) to be raked up mechanically (Jiffler Mixer large) and to be mixed thoroughly with 1 Part B (hardener) 6 Parts A (base) : 1 Part B (hardener) Component A premix 4 minutes; then Components A+B mix 2 minutes; Mixer cycles >100rpm 30-40 minutes (reduced at higher temperatures) Min. 20oC Thinners should not be added. CERAM-KOTE thinners should be used to clean and flush equipment Check to ensure that filters are clean

Mixing (by weight): Mixing (by volume): Mixing time: Potlife (23o C): Material Spray Temp: Thinner: Filters:

SURFACE PREPARATION: First coating and repair - Gritblasting to minimum Sa 2.5 (ISO 8501-1). Surface is to have a good profile with an average roughness of >50m. CONDITION DURING APPLICATION: Substrate temperature should be above 10oC and at least 3oC above dew point. Relative humidity should be below 85%. Temperature and relative humidity must be measured in the vicinity of the substrate. DRYING TIME: Substrate Fully cured Chemically Temperature resistant o 23 C 48 hrs* 7d Recoating time (Wet/Wet) . Minimum Maximum 10 hrs 24 hrs

STORAGE AND PACKING: Preferred storage conditions are to keep the containers in a dry and cool area below 35oC provided with adequate ventilation. The containers should be sealed tightly. Packing: Shelf life:
HEALTH AND SAFETY: Observe the precationary notices on the container label, and read the Material Safety Data Sheet before use. The product is intended for use by properly qualified professional applicators in industrial conditions. The product is flammable and should be kept away from sparks, open flames, and other sources of ignition. Smoking is prohibited in the application area. Wear suitable respiratory equipment and apply in well ventilated areas. Avoid contact with skin and eyes. Disclaimer: The information in this data sheet is given to the best of our knowledge based on laboratory testing and practical experience. However, as the product is often used under conditions beyond our control, we can not guarantee anything but the quality of the product itself. We reserve the right to change the given data without notice.
Stand 05/07, letzte nderung am 02.05.2007

16.5kg-kits including hardener See labels for shelf life details.

Das könnte Ihnen auch gefallen