Beruflich Dokumente
Kultur Dokumente
com
UR24A Multi-channel UART Wireless Module
OVERVIEW
The UR24A is a low-cost module. Integrated with High-performance RF IC and High-speed MCU, users can
easily use it to transfer data, without programming and complex settings.
Applications
2400-2483.5MHz ISM/SRD band systems
Consumer electronics
Access control, Attendance, Logistics
Smart Furniture
Robert
Wireless sensor
Features
DC Supply2.95 to 3.6V
Serial baud rate2400 to 115200
Max Power+1dBm
256 byte buffer for receiver or transmitter
Compatible with 5V TTL and CMOS
Support the 2-FSK, GFSK and MSK modulation
High receiving sensitivity
Standard 2.54mm Pitch Pin
Pin
Pin Symbol Function
1 GND Ground
2 VCC Voltage supply2.95-3.6V
3 IO1 0LOW-- configure mode.
1HIGH-- running mode
4 RX Serial receive Pin
5 TX Serial send Pin
6 IO2 Sleep controlLow -- sleep
General connection module
Module Size
Length: 23.4mm
Wide: 16.4mm
Thickness:3.8mm
UR24A
PC
TX
TX RX
RX
VCC
TTL or 232
GND
www.amp-tronics.com
CONFIGURATION
Tool Configuration
Command Configuration
You can send command via serial interface to configure this module
Steps to configure uR24A
1. First set IO1 low and reset uR24A.
www.amp-tronics.com
2. Then send commands at 9600 baud rates.
3. Disconnect IO1.
Parameter:
Parameters Command Function Default
Baud rate 00 Support 240048009600192005760038400115200 9600
Air speed 01 Support 500kbps250kpbs10kbps2.4kbps 2.4Kbps
Frequency channel 02 256 channelswith 200K interval Channel 0
Power 03 Support +1dbm0dbm-2dbm-4dbm +1dbm
Command:
First BYTE Second BYTE
COMMAND Number ParameterCONF
Respond:
First BYTE Second BYTE
COMMAND Number Status:
00----------- Fail
01----------- Success
COMMAND 0
Configure the serial baud rate
Command Number Parameter
00 Baud rate
Baud rate Parameter
Parameter Serial baud rate
FC 115200
F8 57600
F4 38400
F0 19200
D0 9600
A0 4800
40 2400
COMMAND 1
Configure Air speed
Command Number Parameters
01 Rf rate
www.amp-tronics.com
RF rate:
RF rate Air Speed
00 500kbps
01 250kbps
02 10kbps
03 2.4kbps
COMMAND 2
Configure Frequency
Command Number Parameters
02 Freq
Freq:
Freq Frequency
00 Channel 0
01 Channel 1
FF Channel 255
COMMAND 3
Configure Power
Command Number Parameters
03 Power
Power:
Power Output Power
FF +1dbm
FE 0dbm
BB -2dbm
A9 -4dbm
COMMAND 4
Read the configure Parameters
Command Number Parameters
04 FF
Response of COMMAND 4
First byte Serial baud rate Such asD0
Second byte Air speed
www.amp-tronics.com
Third byte Frequency channel
Forth byte Power
Fifth byte Reserved
Sixth byte Reserved
Electrical characteristics
Power supply
Min - Max More
VCC 2.95V 3.6V Close to the minimum power consumption
is low, near the upper limit have better
communication distance
IOV 0V - 6.5V IO Support 5V TTL and
3.3V CMOS
Consumption:
Conditions Averagewith led Averagewithout led
Sleep mode 1.2MA 80uA
Working mode 22.2MA 20.8MA
www.amp-tronics.com