Beruflich Dokumente
Kultur Dokumente
APPLICATION:
Used as oil or water dump valves on separators, treaters, knockouts, and other similar liquid accumulators where higher pressures may occur.
OPERATION:
FEATURES:
Balanced, single soft seat Teflon packed, rotary stuffing box All internal parts easily be removed with valve in line
The Oil Valve is mechanically operated through a LEVER by a Float in a separator or other vessel to which the valve is connected. The STEM AND SEAT ASSEMBLY is driven through a crank by the LEVER. The area of the PISTON is the same as the area of the SEAT so that Separator Fluid Pressure (Green) acting down on the SEAT is cancelled by the upward force of the pressure on the PISTON. Downstream Pressure (Blue) is communicated through the hollow STEM to the top side of the PISTON. Downstream Pressure (Blue) acting up on the SEAT is cancelled by the downward force of the same pressure on the top side of the PISTON. The valve can be operated easily by float since it is unaffected by Separator Fluid Pressure (Green) or Downstream Pressure (Blue). The entire STEM AND SEAT ASSEMBLY with the CAGE can be withdrawn from the valve as a unit by removing the BONNET screws.
Lever
Bonnet
Piston
Stem
Cage Seat
www.kimray.com
NOTE:
The Customer is responsible for specifying linkage arm lengths and proper installation of float trunnions, valves and linkage assemblies. The total resulting force generated by the float is a function of the size and density of the float, the specific gravity of the fluid, the lever arm positions and angles and proper installation of the equipment. These criteria at least should be considered when specifying and installing linkage assemblies between vessels and valves.
NOTE: This valve contains Ductile & Cast Iron wetted parts & Brass packing material.
ANGLE VALVES AVAILABLE:
CAT. NO. CAR CAW CAY SIZE TYPE VALVE 2" FLGD. 3" FLGD. 4" FLGD. 228 FOA PB-S 327 FOA PB-S 427 FOA PB-S OPER. PRES. 285 285 285 MAX W.P. 285 285 285 KIT RNA RNB RNC
*These are recommended spare parts and are stocked as repair kits.
Configuration of Mechanical Oil Valve ia a trademark of Kimray, Inc. Current Revision: Chg. 2" Packing Ring qty. & Chg. trom page C2:20.2 www.kimray.com
For gravity correction, multiply the above figures by G Where G is the specific gravity of the flowing liquid. NOTE: Flow rates are for steady flow conditions over a 24 hour period. Corrections should be made to deal with intermittent flow conditions.
www.kimray.com
MECHANICAL OIL VALVES CAGE & HARD SEAT ASSEMBLY CAST IRON
316, 2" Pin With Snap Rings, 2 Req'd. 317, 3" & 4" 1790, 6" Trunnion Hub 298, 2" 299, 3" 300, 4" 2351, 6"
318SS6, 2" Link, 2 Req'd. 319SS6, 3"&4" 2352, 6" 335, 2" 336, 3" Diaphragm 4700, 4" 4315, 6" 323SS6, 324SS6, Plate 325SS6, 2347, Stem Cage LINE SIZE 2" 3" 4" 6" STD. C.I. 1751 1759 1761 ---CAST DUCT. ---------2357 CAST STEEL 3097 3098 3099 ---326, 2" 327, 3" 328, 4" 2350, 6" 2" 3" 4" 6"
320, 2" 3 2 1 , 3" Nut 3 2 2 , 4" 2346, 6" 329, 2" 330, 3" O Ring 3 3 1 , 4" 2353, 6" Removable Seat LINE SIZE 2" 3" 4" 6" STD 17-4 1752PH 1760PH 1762PH 2358PH D-2 STEEL ----1760 1762 2358 316SS STEEL 1752SS6 1760SS6 1762SS6 2358SS6
1811, 2" Ratio Guide Plug 333, 3" 334, 4" 2348, 6" 312, 2" 3" Disc 313, 160, 4" 2349, 6" Lock Nut 173, 2" 906, 3" & 4" 175SS6, 6"
Gasket
O Ring 265, 2" 310P, 2" 3 1 1 P , 3" Seat 1 6 5 P , 4" 2356P, 6"
ASSEMBLIES AVAILABLE:
CAT. NO. TYPE VALVE CBS1 CBT1 CBU1 CBV1 2" 3" 4" 6" 212 312 412 612 S/FOA S/FOA S/FOA FOA OPER. PRESS. 125 125 125 125 MAX W.P. 175 175 175 175
NOTES:
NOTE: To order valve with removable seat, specify valve model, then add with removable seat.
www.kimray.com
3 3/4" 12 3/16" 3 3/4" 13 1/4" 10 3/8" 1 3/8" 4 1/2" 15 1/8" 4 1/2" 15 5/16" 11 11/16" 1 3/8" 4 7/8" 22" 5 1/2" 11 5/16" 12 3/16" 1 5/8"
4 1/2" 14 15/16" 9 5/16" 1 3/8" 5 1/2" 21 1/4" 1 17/8" 1 5/8" 5 1/2" 21 5/16" 12 3/16" 1 5/8"
101/4" 7 3/4"
Current Revision:
www.kimray.com