Beruflich Dokumente
Kultur Dokumente
Description
Paper misfeeding
E110 E120 E130 E140 E150 E160 E190 ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing. Bypass misfeeding (Paper not reaching the bypass feed sensor): Paper fed from the bypass tray does not reach the bypass feed sensor. 1st drawer misfeeding (Paper not reaching the 1st drawer feed sensor): The paper fed from the 1st drawer does not reach the 1st drawer feed sensor. 2nd drawer misfeeding (Paper not reaching the 2nd drawer feed sensor): The paper fed from the 2nd drawer does not reach the 2nd drawer feed sensor. PFP upper drawer misfeeding (Paper not reaching the PFP upper drawer feed sensor): The paper fed from the PFP upper drawer does not reach the PFP upper drawer feed sensor. PFP lower drawer misfeeding (Paper not reaching the PFP lower drawer feed sensor): The paper fed from the PFP lower drawer does not reach the PFP lower drawer feed sensor. LCF misfeeding (Paper not reaching the LCF feed sensor): The paper fed from the LCF does not reach the LCF feed sensor.
drawer feed sensor after it has passed the PFP upper drawer feed sensor. E330 E340 E350 E360 E3C0 E3D0 E3E0 PFP lower drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor. PFP lower drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor. PFP lower drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the PFP upper drawer feed sensor. PFP lower drawer transport jam (Paper not reaching the PFP upper drawer feed sensor): The paper does not reach the PFP upper drawer feed sensor after it has passed the PFP lower drawer feed sensor. LCF transport jam (Paper not reaching the registration sensor): Paper fed from the LCF and passed through the 1st drawer feed sensor does not reach the registration sensor. LCF transport jam (Paper not reaching the registration sensor): Paper fed from the LCF and passed through the 1st drawer feed sensor does not reach the registration sensor. LCF transport jam (Paper not reaching the 2nd drawer feed sensor): Paper fed from the LCF and passed through the LCF feed sensor does not reach the 2nd drawer feed sensor.
RADF jam
E712 E714 E721 E722 E724 E725 E726 E731 E860 Jam not reaching the original registration sensor: The original fed from the original feeding tray does not reach the original registration sensor Feed signal reception jam: The feed signal is received even no original exists on the original feeding tray. Jam not reaching the read sensor: The original does not reach the read sensor after it has passed the registration sensor (when scanning obverse side) or the reverse sensor (when scanning reverse side). Jam not reaching the original exit/reverse sensor (during scanning): The original which passed the read sensor does not reach the original exit/reverse sensor when it is transported from the scanning section to exit section. Stop jam at the original registration sensor: The trailing edge of the original does not pass the original registration sensor after its leading edge has reached this sensor. Stop jam at the read sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor. Transport/exit signal reception jam: RADF receives the transport/exit reception signal from the equipment when no original is at the exposure waiting position Stop jam at the original exit/reverse sensor: The trailing edge of the original does not pass the original exit/reverse sensor after its leading edge has reached this sensor. RADF jam access cover open: The RADF jam access cover has opened during RADF operation.
E870 E871
RADF open jam: RADF has opened during RADF operation Cover open jam in the read ready status
EAD0
Print end command time-out jam: The printing has not finished normally because of an error occurring on the interface between the SYS board and the engine firmware at the end of printing.
Finisher jam
EAE0 EB30 Receiving time time-out jam: The printing has been interrupted because of the communication error between the equipment and finisher when the paper is transported from the equipment to the finisher. Ready time time-out jam: The equipment judges that the paper transport to the finisher is disabled because of the communication error between the equipment and finisher at the start of printing.
Finisher jam
ED10 ED11 ED12 ED13 ED14 ED15 ED16 EF10 EF11 EF12 EF13 EF14 EF15 EF16 EF17 EF18 EF19 EF20 Skew adjustment motor (M1) home position detection abnormality: The Skew adjustment motor is not at the home position. [MJ-1101/ 1106 (when MJ-6103 is installed)] Sideways adjustment motor (M2) home position detection error: The Sideways adjustment motor is not at the home position. [MJ-1101/1106 (when MJ-6103 is installed)] Shutter home position error: The shutter is not at the home position. [MJ-1101/1106] Front alignment plate home position error: The front alignment plate is not at the home position. [MJ-1101/1106] Rear alignment plate home position error: The rear alignment plate is not at the home position. [MJ-1101/1106] Paddle home position error: The paddle is not at the home position. [MJ-1101/1106] Buffer tray home position error: The buffer tray is not at the home position. [MJ-1101/1106] Paper not supported for Saddle Stitch Finisher: Unsupported paper size, type and an excess number of pages for stapling are selected. [MJ- 1106] Saddle Stitch Finisher stapling error (front): Front stapling is not correctly done. [MJ-1106] Saddle Stitch Finisher stapling error (rear): Rear stapling is not correctly done. [MJ-1106] Saddle paper holder home position detection abnormality: The paper holder home position cannot be detected. [MJ-1106] Saddle paper exit jam: Outputting paper is not completed within a fixed time. [MJ-1106] Saddle Stitch Finisher side alignment motor home position detection abnormality: The side alignment motor home position cannot be detected. [MJ-1106] Saddle Stitch Finisher stacker motor home position detection abnormality: The stacker motor home position cannot be detected. [MJ- 1106] Saddle Stitch Finisher folding blade home position detection abnormality: The folding blade home position cannot be detected. [MJ- 1106] Saddle Stitch Finisher additional folding roller home position detection abnormality: The additional folding roller home position cannot be detected. [MJ-1106] Saddle paper folding jam: Fold processed paper cannot be transported to the additional folding roller. [MJ-1106] Saddle stacker jam: Transported paper cannot be detected in the stacker.
not moving normally. (the case that paper can be fed from any drawer except the PFP upper drawer) C160 C180 C1A0 C1B0 PFP lower drawer tray abnormality: The PFP lower drawer tray-up motor is not rotating or the PFP lower drawer tray is not moving normally. (the case that paper can be fed from any drawer except the PFP lower drawer) LCF tray-up motor abnormality: The LCF trayup motor is not rotating or the LCF tray is not moving normally. (the case that paper can be fed from any drawer except the LCF) LCF end fence motor abnormality: The LCF end fence motor is not rotating or the LCF end fence is not moving normally. (the case that paper can be fed from any drawer except the LCF) LCF transport motor abnormality: The LCF transport motor is not rotating normally (when paper can be fed from any drawer except the LCF).
C466 C467 C468 C471 C472 C475 C480 C490 C4B0 C4B1 C4C0 C4D0 C4F0 C4F1
Pressure roller thermistor abnormality after entering ready status (pre-running end temperature abnormality) Pressure roller thermistor abnormality after entering ready status (temperature abnormality at ready status) Pressure roller thermistor abnormality after entering ready status (overheating) IH power voltage abnormality or IH initial abnormality (IH board initial abnormality) IH power voltage abnormality (power supply abnormality) IH power voltage abnormality (power supply abnormality when door is opened) Overheating of IGBT: The temperature of the IGBT rises abnormally. IH control circuit or IH coil abnormality: Abnormality is detected in IH control circuit or IH coil is broken/ shorted. Fuser unit counter abnormality Fuser unit destination selection abnormality Fuser unit new/old detection fuse abnormality Fuser belt thermopile abnormality Center thermistor error correction Side thermistor error correction
normally. CB12 CB13 CB14 CB20 CB30 CB31 CB40 CB50 CB51 CB60 CB70 CB80 CB81 CB82 CB83 CB84 CB90 CB91 CB92 CB93 CB94 CB95 CBA0 CBB0 CBC0 CBD0 CBE0 CBF0 CC02 CC00 CC10 CC20 CC21 CC22 CC23 CC30 CC31 Buffer roller drive motor abnormality: The buffer roller drive motor is not rotating or the buffer roller is not moving normally. Finisher exit motor abnormality Paper holding arm motor abnormality Delivery motor abnormality: Delivery motor or delivery roller is not rotating normally. Movable tray shift motor abnormality: The movable tray shift motor is not rotating or the movable tray is not moving normally. Movable tray paper-full detection error: The actuator of the movable tray paper-full detection sensor does not move smoothly. Front alignment motor abnormality: The front alignment motor is not rotating or the front align/1106ment plate is not moving normally. Staple unit abnormality: Staple unit is not moving normally. Stapler home position error: The stapler home position sensor does not work. Stapler shift home position error: The stapler is not at the home position. Stapler shift motor abnormality: Stapler shift motor is not rotating or staple unit is not moving normally. Paper loading amount detection sensor abnormality Backup RAM data abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON. Flash ROM abnormality: Abnormality of checksum value on finisher controller PC board is detected when the power is turned ON. Finisher - Main CPU program error Saddle Stitch Finisher - Main CPU program error Hole Punch Unit - Main CPU program error Paper folding blade motor (M12) abnormality Saddle Stitch Finisher flash ROM abnormality Saddle Stitch Finisher RAM abnormality Additional folding motor abnormality Saddle transport motor abnormality Stacker motor abnormality Front saddle stapler home position error: The stapler home position detection is abnormally operated and finished. Rear saddle stapler home position error: The stapler home position detection is abnormally operated and finished. Saddle Stitch Finisher side alignment motor (M15) abnormality: The alignment motor is not rotating or the alignment plate is not working properly. Guide motor abnormality: Guide motor is not rotating or guide is not moving normally Saddle Stitch Finisher folding motor (M17) abnormality: The folding motor is not rotating or the folding roller is not moving normally. Stacker motor (M9) abnormality Stack exit roller nip home position detection error[MJ-1036] Exit roller nip adjustment motor (M4) abnormality[MJ-1037] Sensor connector abnormality: Connector of guide home position sensor, paper pushing plate home position sensor or paper pushing plate top position sensor is disconnected. Micro switch abnormality: With all covers closed, inlet door switch, delivery door switch or front cover switch is open. Saddle communication error Saddle stitch 3rd transport roller drive motor (M10) abnormality[MJ-1037] Saddle stich stapler home position detection error[MJ-1037] An abnormal interruption of the encoder pulse of the folding blade occurrs. Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. Stack delivery motor abnormality: The stack delivery motor is not rotating normally. Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating
normally. CC40 CC41 CC50 CC51 CC52 CC53 CC54 CC60 CC61 CC71 CC72 CC80 CC90 CC91 CC92 CC93 CC94 CCB0 CCD0 CCE0 CCF0 CCF1 Swing motor abnormality: Swing motor is not rotating or swing unit is not moving normally Paper holder cam home position abnormality: The paper holder cam is not at the home position. Horizontal registration motor abnormality: Horizontal registration motor is not rotating or puncher is not shifting normally Sideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. Skew adjustment motor (M1) abnormality: Skew adjustment motor is not rotating or puncher is not shifting normally. Punch waste full sensors (S41 and S42) abnormality[MJ-1037] Abnormality of paper detection sensors (S24 and S25)[MJ-1036] Abnormality of trailing edge detection sensors (S39 and S40) and horizontal registration detection sensors (S39 and S40)[MJ-1037] Punch motor abnormality [MJ-1036] Punch motor (M15) abnormality [MJ-1037] Punch motor (M3) home position detection error: Punch motor is not rotating or puncher is not shifting normally. Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. Rear alignment motor abnormality: The rear alignment motor is not rotating or the rear alignment plate is not moving normally. Tray shift motor abnormality: The tray shift motor is not rotating or the stack tray is not moving normally. The detection of the home position of the gripper arm ends abnormality. Movable tray upper limit detection error [MJ- 1037] Knurled roller shift solenoid abnormality [MJ- 1036] Fan motor abnormality[MJ-1036] Offset motor abnormality: The offset motor is not rotating normally. Stack ejection motor abnormality: Stack ejection motor or stack ejection roller is not rotating normally Paper trailing edge assist motor abnormality: Paper trailing edge assist motor is not rotating or paper trailing edge assist is not moving normally Gear changing motor abnormality: Gear changing motor is not rotating normally Tray safety switch abnormality (1) The tray safety switch turned on during tray operation (moving up or down). (2) The tray operated with the tray safety switch turned on.
CE70 CE71 CE80 CE81 CE90 CEC0 CEC1 CEC2 CF10 CF90 CF91 CF92 F070 F071 F090
Drum drive switching abnormality: The drum switching detection sensor (S19) is not turned ON after the drum motor was rotated for a specified period of time. Drum phase adjustment abnormality: Drum phase sensors (Color drum phase sensor (S43) and K drum phase sensor (S44)) are not turned ON after the drum motor was rotated for a specified period of time. LED head communication error Interface initialization error between LED head and LGC board Drum thermistor-K abnormality: The output value of the drum thermistor-K is out of a specified range. 2nd transfer roller position detection abnormality: The 2nd transfer roller does not contact/release normally. 2nd transfer roller contacting position detection abnormality 2nd transfer roller releasing position detection abnormality Communication module SRAM reading failure. Laser optical unit shutter abnormality. NVRAM abnormality on the SYS board SRAM and NVRAM abnormality on the SYS board Communication error between System-CPU and Engine-CPU Communication initialization error between System-CPU and Engine-CPU SRAM abnormality on the SYS board
F109_4 F109_5 F109_6 F110 F111 F120 F121 F122 F124 F130 F131 F140 F200 F350 F400 F500 F510 F520 F521 F550 F600 F700 F800 F900 F902_0 F902_1 F902_3
Key consistency error: license data damage. Key consistency error: Encryption key for ADIHDD is damaged. Key consistency error: Administrator password error for ADI-HDD authentication. Communication error between System-CPU and Scanner-CPU Scanner response abnormality Database abnormality: Database is not operating normally. Database abnormality (user information management database) Database abnormality (Message/Job log management database) Database abnormality: Database is not operating normally. (Language management database) Invalid MAC address Error due to damage to filtering setting file ASIC format error: ASIC formatting fails or memory acquiring fails when software is formatted Data Overwrite option (GP-1070) disabled SLG board abnormality SYS board cooling fan abnormality HD partition damage Application start error Operating system start error Integrity check error Encryption partition error Software update error Overwrite error Date error Machine information alignment error Mistaken HDD installation error System firmware / System software model information error - Invalid system firmware/ software is installed on 20/25 ppm model. System firmware / System software model information error - Invalid system firmware/ software is installed on LL20/LL25 ppm model.