Beruflich Dokumente
Kultur Dokumente
T55/T655
Thank you for purchasing this product. Please read this manual carefully before use and retain it for future reference.
Introduction
1.Coaxical-rolor design,built-in gyro and unique function of digital speed setting and operation of the helicopter. It is the best choice for beginner. 2.Adopt aluminurn alloy outer casing,attractive design and elegant appearance. 3.By using of the 2.4G auto connection technology, scores of helicopters can be plaved at the same time with hiah stabilitv. 4.Full charged battery can support the helicopter flys about 7 mins. 5.Tripple circuit protections make the flight more safer and improve the service life of the helicopter. 6.The helicopter has Videography and Photography function.
The wire that fixed on the landing gear is the receiver of the helicopter, disassembling this wire may be dangerous or causes accident.
Major parts
Charging Socket
Helicopter
When not playing the model,please unplug the battery cable from the socket.If it keeps connected, it may result in over discharging.Take out the batteries from the remotecontroller while not playing the model for a long time.
(Not included)
1. Turn on the remote controller, the power indicator light on the remote controller will blink slowly. Slowly push up the throttle control stick to top then push it down to the bottom. Then, the remote controller will send out connectional signal and the indicator light keep blinking before the remote controller finishes signal connection. 2. Insert the battery plug into the helicopter battery sockte at the right side of the helicopter,then, the indicator light of the helicopter will keep flashing rapidly,set the helicopter down to a platform. 3. When the whole auto signal connection process is finished, both indicator lights of helicopter and transmitter are keep ON without blinking, then push up the throttle stick slowly and the helicopter takes off.
OPERATIONAL TIPS
1.User may push either of the control sticks to skip the auto signal connection process once the helicopter finished signal connection. 2.Set the connection one by one. Otherwise, it may not be connected. 3.Once the transmitter is turned off, the connection procedure must be repeated to operate the helicopter. 4.Please pull out the battery plug from the helicopter battery socket.
the servo connecting bar screw the right servo connecting bar clockwise or counter clockwise screw the rear servo connecting bar clockwise or counter clockwise
swashplate
Pic1
Pic2
Pic3
Parallel
Pic4
5
Pic5
Operating
Hints
1.If the helicopter keeps self-rotating in the air even there is no control signal given, you could correct it by adjusting the trimmer of gyro on the remote control.
2.If the helicopter keeps flying forward/backward in the air even there is no control signal given, you could correct it by adjusting the trimmer on the remote control.
TF memory card
videography module
Pic6
Pic7
7
Pic8
1. Turn on the helicopter by push the power switch. At this time, the red light and the green light keep flashing in turn. Two seconds later, the green light keeps ON means it is ready. 2. When the helicopter is finished signal connection and is not under shooting condition, the indicator light of the videography module keeps constant ON. Turn the switch button on videography module to the direction of the videography icon (Pic9), and then turn on the camera switch of the remote control, it will start taking videography and the red light of module keeps flashing. Press the camera button again, videography taking will be stopped. Turn the switch button on videography module to the direction of the photography icon (Pic10), and then press the camera button on the remote control to take photos.
Pic9
Pic10
3. After shooting is finished, take out the TF memory card from the videography module and insert it into the card reader, then, insert the card reader into the USB interface of the computer to watch the video.
TIPS To stop shooting, please press the shooting switch on the remote controller. Directly unplug the battery cable or take out the TF memory card from the videography module will result in loss of the video data. To avoid helicopter crash,please do not insert or take out the TF memory card from the videography module,when the circuit is on. TF memory card should be installed before circuit is on and take out after shooting switch is turned off. When crash occurs,turn off the helicopter and then turn on the power to recover normal working.
Trouble shooting
Problem Reason 1.The helicopter is underpowered. No reaction from the helicopter Solution 1.Get the battery of the helicopter charged
2.The indicator light of the helicopter 2.Set the helicopter down to a platform, until the flashing rapidly, and the gyo is in indicator light turn to constant ON without the testing statement blinking. 3.the helicopter and the transmitter is out of radio connection 3.Repeating the connection procedure.