Beruflich Dokumente
Kultur Dokumente
com
www.jwjobs.net
Code No: A107412404 Set No. 1 JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD IV B.Tech. I Sem., II Mid-Term Examinations, November 2010 VEHICLE BODY ENGINEERING AND SAFETY Objective Exam Name: ______________________________ Hall Ticket No. A Answer All Questions. All Questions Carry Equal Marks.Time: 20 Min. Marks: 20. I 1. Choose the correct alternative: Which of the following car body shapes has the largest internal dimensions? a) coupe b) saloon c) convertible d) estate An enclosed two seater body having a fixed roof a) Couple b) Single c) Saloon d) None [ ]
2.
3.
The fundamental components fixed near to driver seat are a) stereo b) air condition control c) steering, gear and foot control
4.
According to the visibility regulations,horizontal and vertical distance to be visible are a) 12m,5m b) 10m,8m c) 8m,10m d) None A fuse in an electrical circuit blows as the result of a high a) Voltage caused by a short circuit b) Current flow caused by a short circuit c) Voltage caused by an open circuit d) Current flow caused by an open circuit
5.
6.
In car a temperature indicating instrument is usually provided which indicates the temperature of [ ] a) Engine piston b) Engine cylinder c) Lubricating oil d) Jacket cooling water Noisy brakes indicate a) rift on lining b) drums scored
7.
8.
To balance a single cylinder engine a counter weight is added to a) piston b) connecting rod c) crankshaft
T N
W U
R O
D L
[ d) none [
9.
The frame provided for supporting the unit of chassis and body, in case of Tata vehicles is[ a) cross member-type frame b) center beam frame c) Y-shaped tube frame d) Self supporting structure The pressure of air in case of heavy duty truck is usually of the order of [ a) 1 to 2 atm b) 2 to 3 atm c) 4 to 7 atm d) Depends of the roads conditions Cont..2
10.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Code No: A107412404 II 11. 12. 13. 14. Fill in the blanks
:2:
Set No. 1
In a vehicle the probable cause for hard steering could be____________ A frame consisting of side and cross members of channel section is normally used on____________ As applied to the specification of a heavy commercial vehicle the abbreviation g.v.w is__________ Most motor cars use a specially constructed body shell onto which the main components are attached.It is called ____________ type The type of engine used in a heavy commercial vehicle is _____________ When a vehicle turns a corner, the action of the differential causes______________ A collapsible steering column is one which collapses to ____________ Fluid drive is one name for _____________
The factor not considered to oppose the motion of the vehicle is ______________ The part of the vehicle which holds the passengers and the cargo to be transported is known as ____________
T N
W U
-oOo-
R O
D L
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Code No: A107412404 Set No. 2 JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD IV B.Tech. I Sem., II Mid-Term Examinations, November 2010 VEHICLE BODY ENGINEERING AND SAFETY Objective Exam Name: ______________________________ Hall Ticket No. A Answer All Questions. All Questions Carry Equal Marks.Time: 20 Min. Marks: 20. I 1. Choose the correct alternative: According to the visibility regulations,horizontal and vertical distance to be visible are a) 12m,5m b) 10m,8m c) 8m,10m d) None A fuse in an electrical circuit blows as the result of a high a) Voltage caused by a short circuit b) Current flow caused by a short circuit c) Voltage caused by an open circuit d) Current flow caused by an open circuit [ ]
2.
3.
In car a temperature indicating instrument is usually provided which indicates the temperature of [ ] a) Engine piston b) Engine cylinder c) Lubricating oil d) Jacket cooling water Noisy brakes indicate a) rift on lining b) drums scored
4.
5.
To balance a single cylinder engine a counter weight is added to a) piston b) connecting rod c) crankshaft
6.
The frame provided for supporting the unit of chassis and body, in case of Tata vehicles is[ a) cross member-type frame b) center beam frame c) Y-shaped tube frame d) Self supporting structure The pressure of air in case of heavy duty truck is usually of the order of [ a) 1 to 2 atm b) 2 to 3 atm c) 4 to 7 atm d) Depends of the roads conditions Which of the following car body shapes has the largest internal dimensions? a) coupe b) saloon c) convertible d) estate An enclosed two seater body having a fixed roof a) Couple b) Single c) Saloon d) None [ d) none Cont..2 [
7.
T N
W U
R O
D L
8.
9.
10.
The fundamental components fixed near to driver seat are a) stereo b) air condition control c) steering, gear and foot control
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
:2:
Set No. 2
Most motor cars use a specially constructed body shell onto which the main components are attached.It is called ____________ type The type of engine used in a heavy commercial vehicle is _____________ When a vehicle turns a corner, the action of the differential causes______________ A collapsible steering column is one which collapses to ____________ Fluid drive is one name for _____________ The factor not considered to oppose the motion of the vehicle is ______________
The part of the vehicle which holds the passengers and the cargo to be transported is known as ____________ In a vehicle the probable cause for hard steering could be____________
A frame consisting of side and cross members of channel section is normally used on____________ As applied to the specification of a heavy commercial vehicle the abbreviation g.v.w is__________
T N
W U
-oOo-
R O
D L
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Code No: A107412404 Set No. 3 JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD IV B.Tech. I Sem., II Mid-Term Examinations, November 2010 VEHICLE BODY ENGINEERING AND SAFETY Objective Exam Name: ______________________________ Hall Ticket No. A Answer All Questions. All Questions Carry Equal Marks.Time: 20 Min. Marks: 20. I 1. Choose the correct alternative: In car a temperature indicating instrument is usually provided which indicates the temperature of [ ] a) Engine piston b) Engine cylinder c) Lubricating oil d) Jacket cooling water Noisy brakes indicate a) rift on lining b) drums scored
2.
3.
To balance a single cylinder engine a counter weight is added to a) piston b) connecting rod c) crankshaft
4.
The frame provided for supporting the unit of chassis and body, in case of Tata vehicles is[ a) cross member-type frame b) center beam frame c) Y-shaped tube frame d) Self supporting structure The pressure of air in case of heavy duty truck is usually of the order of [ a) 1 to 2 atm b) 2 to 3 atm c) 4 to 7 atm d) Depends of the roads conditions Which of the following car body shapes has the largest internal dimensions? a) coupe b) saloon c) convertible d) estate An enclosed two seater body having a fixed roof a) Couple b) Single c) Saloon
5.
6.
7.
8.
The fundamental components fixed near to driver seat are a) stereo b) air condition control c) steering, gear and foot control
T N
W U
R O
D L
[ d) gudgeon pin
[ d) None [ d) none [
9.
According to the visibility regulations,horizontal and vertical distance to be visible are a) 12m,5m b) 10m,8m c) 8m,10m d) None A fuse in an electrical circuit blows as the result of a high a) Voltage caused by a short circuit b) Current flow caused by a short circuit c) Voltage caused by an open circuit d) Current flow caused by an open circuit
10.
Cont..2
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Code No: A107412404 II 11. 12. 13. 14. 15. Fill in the blanks
:2:
Set No. 3
When a vehicle turns a corner, the action of the differential causes______________ A collapsible steering column is one which collapses to ____________ Fluid drive is one name for _____________ The factor not considered to oppose the motion of the vehicle is ______________ The part of the vehicle which holds the passengers and the cargo to be transported is known as ____________ In a vehicle the probable cause for hard steering could be____________
A frame consisting of side and cross members of channel section is normally used on____________ As applied to the specification of a heavy commercial vehicle the abbreviation g.v.w is__________ Most motor cars use a specially constructed body shell onto which the main components are attached.It is called ____________ type The type of engine used in a heavy commercial vehicle is _____________
20.
T N
W U
-oOo-
R O
D L
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Code No: A107412404 Set No. 4 JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD IV B.Tech. I Sem., II Mid-Term Examinations, November 2010 VEHICLE BODY ENGINEERING AND SAFETY Objective Exam Name: ______________________________ Hall Ticket No. A Answer All Questions. All Questions Carry Equal Marks.Time: 20 Min. Marks: 20. I 1. Choose the correct alternative: To balance a single cylinder engine a counter weight is added to a) piston b) connecting rod c) crankshaft [ d) gudgeon pin ]
2.
The frame provided for supporting the unit of chassis and body, in case of Tata vehicles is[ a) cross member-type frame b) center beam frame c) Y-shaped tube frame d) Self supporting structure The pressure of air in case of heavy duty truck is usually of the order of [ a) 1 to 2 atm b) 2 to 3 atm c) 4 to 7 atm d) Depends of the roads conditions Which of the following car body shapes has the largest internal dimensions? a) coupe b) saloon c) convertible d) estate An enclosed two seater body having a fixed roof a) Couple b) Single c) Saloon
3.
4.
5.
6.
The fundamental components fixed near to driver seat are a) stereo b) air condition control c) steering, gear and foot control
7.
According to the visibility regulations,horizontal and vertical distance to be visible are a) 12m,5m b) 10m,8m c) 8m,10m d) None A fuse in an electrical circuit blows as the result of a high a) Voltage caused by a short circuit b) Current flow caused by a short circuit c) Voltage caused by an open circuit d) Current flow caused by an open circuit
8.
T N
W U
R O
D L
d) None [ d) none [ ]
9.
In car a temperature indicating instrument is usually provided which indicates the temperature of [ ] a) Engine piston b) Engine cylinder c) Lubricating oil d) Jacket cooling water Noisy brakes indicate a) rift on lining b) drums scored [ d) any of the above Cont..2 ]
10.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Code No: A107412404 II 11. 12. 13. Fill in the blanks Fluid drive is one name for _____________
:2:
Set No. 4
The factor not considered to oppose the motion of the vehicle is ______________ The part of the vehicle which holds the passengers and the cargo to be transported is known as ____________ In a vehicle the probable cause for hard steering could be____________ A frame consisting of side and cross members of channel section is normally used on____________ As applied to the specification of a heavy commercial vehicle the abbreviation g.v.w is__________ Most motor cars use a specially constructed body shell onto which the main components are attached.It is called ____________ type The type of engine used in a heavy commercial vehicle is _____________ When a vehicle turns a corner, the action of the differential causes______________ A collapsible steering column is one which collapses to ____________
T N
W U
-oOo-
R O
D L
www.jntuworld.com