Beruflich Dokumente
Kultur Dokumente
D D D D D D D D
Targeted Specifically for High-Speed Memory Decoders and Data-Transmission Systems Wide Operating Voltage Range of 2 V to 6 V Outputs Can Drive Up To 10 LSTTL Loads Low Power Consumption, 80-A Max ICC Typical tpd = 10 ns 4-mA Output Drive at 5 V Low Input Current of 1 A Max Incorporate Two Enable Inputs to Simplify Cascading and/or Data Reception
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
description/ordering information
The HC139 devices are designed for high-performance memory-decoding or data-routing applications requiring very short propagation delay times. In high-performance memory systems, these decoders can minimize the effects of system decoding. When employed with high-speed memories utilizing a fast enable circuit, the delay time of these decoders and the enable time of the memory usually are less than the typical access time of the memory. This means that the effective system delay introduced by the decoders is negligible.
2A 2B NC 2Y0 2Y1
NC No internal connection
The HC139 devices comprise two individual 2-line to 4-line decoders in a single package. The active-low enable (G) input can be used as a data line in demultiplexing applications. These decoders/demultiplexers feature fully buffered inputs, each of which represents only one normalized load to its driving circuit. ORDERING INFORMATION
TA PDIP N SOIC D 40C to 85C SOP NS SSOP DB TSSOP PW CDIP J 55C to 125C CFP W LCCC FK PACKAGE Tube Tube Tape and reel Tape and reel Tape and reel Tube Tape and reel Tube Tube Tube ORDERABLE PART NUMBER SN74HC139N SN74HC139D SN74HC139DR SN74HC139NSR SN74HC139DBR SN74HC139PW SN74HC139PWR SNJ54HC139J SNJ54HC139W SNJ54HC139FK TOP-SIDE MARKING SN74HC139N HC139 HC139 HC139 HC139 SNJ54HC139J SNJ54HC139W
SNJ54HC139FK Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2002, Texas Instruments Incorporated
On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters.
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
1G
5 1Y1
6 2 1A 7 1B 3
1Y2
1Y3
12 2Y0 15 2G 11 2Y1
10 2Y2 2A 2B Pin numbers shown are for the D, DB, J, N, NS, PW, and W packages. 14 13 9 2Y3
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 V to 7 V Input clamp current, IIK (VI < 0 or VI > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Output clamp current, IOK (VO < 0 or VO > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Package thermal impedance, JA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73C/W DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65C to 150C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7.
TA Operating free-air temperature 55 125 40 85 C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS VCC 2V IOH = 20 A VOH VI = VIH or VIL IOH = 4 mA IOH = 5.2 mA IOL = 20 A VOL VI = VIH or VIL IOL = 4 mA IOL = 5.2 mA II ICC Ci VI = VCC or 0 VI = VCC or 0, IO = 0 4.5 V 6V 4.5 V 6V 2V 4.5 V 6V 4.5 V 6V 6V 6V 2 V to 6 V 3 MIN 1.9 4.4 5.9 3.98 5.48 TA = 25C TYP MAX 1.998 4.499 5.999 4.3 5.8 0.002 0.001 0.001 0.17 0.15 0.1 0.1 0.1 0.1 0.26 0.26 100 8 10 SN54HC139 MIN 1.9 4.4 5.9 3.7 5.2 0.1 0.1 0.1 0.4 0.4 1000 160 10 MAX SN74HC139 MIN 1.9 4.4 5.9 3.84 5.34 0.1 0.1 0.1 0.33 0.33 1000 80 10 nA A pF V V MAX UNIT
switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1)
PARAMETER FROM (INPUT) TO (OUTPUT) VCC 2V A or B tpd d G Y Y 4.5 V 6V 2V 4.5 V 6V 2V tt Y 4.5 V 6V MIN TA = 25C TYP MAX 47 14 12 39 11 10 38 8 6 175 35 30 175 35 30 75 15 13 SN54HC139 MIN MAX 255 51 44 255 51 44 110 22 19 SN74HC139 MIN MAX 220 44 38 220 44 38 95 19 16 ns ns UNIT
LOAD CIRCUIT
NOTES: A. CL includes probe and test-fixture capacitance. B. Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators having the following characteristics: PRR 1 MHz, ZO = 50 , tr = 6 ns, tf = 6 ns. C. The outputs are measured one at a time with one input transition per measurement. D. tPLH and tPHL are the same as tpd.
MECHANICAL DATA
MCER002C JANUARY 1995 REVISED JUNE 1999
J (R-GDIP-T**)
14 LEADS SHOWN
CERAMIC DUAL-IN-LINE
14 0.310 (7,87) 0.290 (7,37) 0.785 (19,94) 0.755 (19,18) 0.300 (7,62) 0.245 (6,22)
16 0.310 (7,87) 0.290 (7,37) 0.785 (19,94) 0.755 (19,18) 0.300 (7,62) 0.245 (6,22)
20 0.310 (7,87) 0.290 (7,37) 0.975 (24,77) 0.930 (23,62) 0.300 (7,62) 0.245 (6,22)
B MAX C B MIN
C MAX
C MIN
0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0.023 (0,58) 0.015 (0,38) 0.100 (2,54) 0.014 (0,36) 0.008 (0,20)
015
4040083/E 03/99 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package is hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification. Falls within MIL STD 1835 GDIP1-T14, GDIP1-T16, and GDIP1-T20
MECHANICAL DATA
MCFP004A JANUARY 1995 REVISED FEBRUARY 2002
W (R-GDFP-F16)
0.006 (0,15) 0.080 (2,03) 0.055 (1,40) 0.305 (7,75) MAX 1 16 0.019 (0,48) 0.015 (0,38) 0.004 (0,10)
0.050 (1,27)
NOTES: A. B. C. D. E.
All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification only. Falls within MIL STD 1835 GDFP-1F16 and JEDEC MO-092AC
MECHANICAL DATA
MLCC006B OCTOBER 1996
FK (S-CQCC-N**)
28 TERMINAL SHOWN
18
17
16
15
14
13
12
NO. OF TERMINALS ** 11 10 28 9 8 7 6 68 5 84 44 52 20
A MIN 0.342 (8,69) 0.442 (11,23) 0.640 (16,26) 0.739 (18,78) 0.938 (23,83) 1.141 (28,99) MAX 0.358 (9,09) 0.458 (11,63) 0.660 (16,76) 0.761 (19,32) 0.962 (24,43) 1.165 (29,59) MIN 0.307 (7,80) 0.406 (10,31) 0.495 (12,58) 0.495 (12,58) 0.850 (21,6) 1.047 (26,6)
B MAX 0.358 (9,09) 0.458 (11,63) 0.560 (14,22) 0.560 (14,22) 0.858 (21,8) 1.063 (27,0)
19 20 21 B SQ 22 A SQ 23 24 25
26
27
28
4040140 / D 10/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a metal lid. The terminals are gold plated. Falls within JEDEC MS-004
MECHANICAL
MPDI002C JANUARY 1995 REVISED DECEMBER 20002
N (R-PDIP-T**)
16 PINS SHOWN
A MIN
MS-100 VARIATION
AA
BB
AC
AD
0.325 (8,26) 0.300 (7,62) 0.015 (0,38) 0.200 (5,08) MAX Seating Plane 0.125 (3,18) MIN 0.010 (0,25) NOM Gauge Plane
D 4040049/E 12/2002
NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001, except 18 and 20 pin minimum body lrngth (Dim A). D. The 20 pin end lead shoulder width is a vendor option, either half or full width.
MECHANICAL DATA
MSOI002B JANUARY 1995 REVISED SEPTEMBER 2001
D (R-PDSO-G**)
8 PINS SHOWN 0.050 (1,27) 8 5 0.020 (0,51) 0.014 (0,35) 0.010 (0,25)
0.010 (0,25)
Seating Plane 0.069 (1,75) MAX 0.010 (0,25) 0.004 (0,10) 0.004 (0,10)
4040047/E 09/01 NOTES: A. B. C. D. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15). Falls within JEDEC MS-012
MECHANICAL DATA
MSOP002 OCTOBER 1994
NS (R-PDSO-G**)
14 PINS SHOWN 1,27 14 8 0,51 0,35 0,25 M
Seating Plane 2,00 MAX 0,05 MIN PINS ** DIM A MAX 14 16 20 24 0,10
10,50
10,50
12,90
15,30
A MIN
9,90
9,90
12,30
14,70
4040062 / B 02/95 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Body dimensions do not include mold flash or protrusion, not to exceed 0,15.
MECHANICAL DATA
MSSO002E JANUARY 1995 REVISED DECEMBER 2001
DB (R-PDSO-G**)
28 PINS SHOWN 0,65 28 0,38 0,22 15 0,15 M
PLASTIC SMALL-OUTLINE
14
16
20
24
28
30
38
6,50
6,50
7,50
8,50
10,50
10,50
12,90
A MIN
5,90
5,90
6,90
7,90
9,90
9,90
NOTES: A. B. C. D.
All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150
MECHANICAL DATA
MTSS001C JANUARY 1995 REVISED FEBRUARY 1999
PW (R-PDSO-G**)
14 PINS SHOWN
0,65 14 8
0,30 0,19
0,10 M
0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 A 7 0 8 0,75 0,50
14
16
20
24
28
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TIs terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TIs standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding thirdparty products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265