Beruflich Dokumente
Kultur Dokumente
Operating Procedure
R-322N, R-323N, R-325N, R-335N, R-315N, R-322, R-323, R-325, R-335, R-315, R-326
OPERATIONAL PROCEDURE
The operational procedure in this guide is described based on the default software parameter settings (preferences). Changing preferences may cause a different operational procedure. For further detail of preferences, please refer to the instruction manual of PCS300 software. This guide uses the symbol " xN " as an expression of repeating times of key operation. For example, " ESC x2 " means that [ESC] key is pressed two times.
Note: To input a new station number, press [ENT] at the first "0000" line, and input the number, and then a point description, X, Y, and Z coordinate:
MODE S. Func
ESC
or
MODE A screen
F5
F1
SELECT
F5
ENT
example:
MODE A screen 0 0 7 1 0 9
F5
ENT x2
Note: 007 commands are listed in the table below. Special functions are also accessible by the HELP MENU. For HELP MENU procedure, refer to "2. Changing Instrument Settings" of the Quick reference Guide, Basic Procedures for R-300. PCS300 software adds the following functions to the HELP MENU Instrument Setting. .
ENT
ENT
F1 F4
x2
FORESIGHT NUMBER LIST screen
ENT
Menu No. 24. 25. 26. 27. 28. 29. 30. 31. 32.
Functions Distance Stakeout RDM Coordinates Offset Shots Coord. Stakeout REM Resection Data Storage Memory Management
"007" command No. 101 103 104 105 109 112 113 119 200
Note: To input new point information, press [ENT] key at the first "0000" line, and input the number, and then a point description, X, Y, and Z coordinate. F2 [STORE] key saves the input data in memory. Orientation can be also made by azimuth angle input from the next ANGLE COMPARE screen, instead of selecting the backsight point. Proceed to the next step:
ENT
F1
SELECT
F4
F5
ENT
ANGLE COMPARE screen
2. COORD. STAKEOUT
To start Coord. Stakeout:
Special Function menu F4
007-109
ENT
COORD.STAKE OUT menu
x2
ANG/DIST
ENT
ENT
F1 F4
Note: To set the azimuth angle, Note: To create a new job, press [ENT] at the first empty line and input a job name. aim at the backsight point
H.INPUT
F2
ENT
F1
TRACK
F2
ENT
ENT
PRISM H
F3
ENT
ENT
F1
To quit:
FORESIGHT NUMBER LIST screen
ESC x2
Note: In the RDM Ref.-P screen, the distance and the grade % from the reference point to the first point are displayed.
3. DISTANCE STAKEOUT
Special Function menu F4
007-101
DIST. STAKE OUT screen
PRISM H
F3 DISP F4
X7
ENT
ENT
F1
F3
SELECT
F4
F5
Note: In the RDM P-P screen, the distance and the grade % from the previous point are displayed.
DIST. COMPARE screen
ENT
x2
To quit:
RDM POINT screen
ESC x2
-4-
F2
Note: F3 [TARGT] switches the EDM mode to Prism -> Reflecting sheet -> Reflecterless -> Prism -> , each time it is pressed. After TRACK measurement, the target position can be measured accurately by using F1 [MEAS].
5. COORDINATES
Special Function menu
007-104
ENT
COORDINATES menu
F4
To quit:
DIST. COMPARE screen
ENT
ENT
F1 F4
COORDINATES menu
Note: To create a new job, press [ENT] at the first empty line and input a job name.
4. RDM
Special Function menu F4
007-103
X5
ENT
RDM Ref. screen
ENT
F4
F1
ENT
MEAS
F3
ENT
F1
Note: F2 [TARGT] switches the EDM mode to Prism -> Reflecting sheet -> Reflecterless -> Prism -> , each time it is pressed. F4 [DIST] is a toggle switch to change the distance display between H.dist, S.dist and V.Dist.
Note: To input a new station number, press [ENT] at the first "0000" line, and input the number, and then a point description, X, Y, and Z coordinate, and the instrument height:
STATION COORDINATES INPUT screen
SELECT
F5
press ENT at the last item F2 [STORE] saves the input data in memory.
ENT
ENT
ENT
F1 F4
SELECT
F5
ENTx2
SURVEY screen
F2 [STORE] saves the input data in memory. Note: To input new point information, press [ENT] at the first "0000" line, and input the number, and then a point description, X, Y, and Z coordinate. F2 [STORE] saves the input data in memory. Orientation can be also made by azimuth angle input from the next SURVEY screen, instead of selecting the backsight point. Proceed to the next step:
ENT
ENT
F1 F4
ENT
SURVEY screen
To measure:
SURVEY screen
MEAS
F1
DISP F4
POINT F3
ENT
Note: To input new point information, press [ENT] at the first "0000" line, and input the number, and then a point description, X, Y, and Z coordinate. F2 [STORE] saves the input data in memory. Orientation can be also made by azimuth angle input from the next SURVEY screen, instead of selecting the backsight point. Proceed to the next step:
next measurement
To measure:
SURVEY screen
MEAS
Note: The point number is automatically incremented or decremented for quick survey. By pressing F5 [1/2], other functions are displayed: F2 [H.INPUT] Input the orientation angle F3 [0 SET] Set the orientation angle to 0 F4 [HOLD] Hold the displayed horizontal angle. F5 [2/2] Toggle switch to change the functions
F1
PRISM F3
ENT
ENT
To quit:
SURVEY screen or COORDINATES screen
Note: By pressing F5 [1/2], another functions are displayed: F2 [H.INPUT] Input the orientation angle F3 [0 SET] Set the orientation angle to 0 F4 [HOLD] Hold the displayed horizontal angle F5 [2/2] Toggle switch to change the functions
ESC x2
ENT
F3
SELECT
F4
F5
6. OFFSET SHOTS
Special Function menu F4
007-105
ENT
OFFSET SHOTS menu
ENT
X3
ENT
F3
ENT
STORE F2 SURVEY screen
F1
F4
Note: To create a new job, press [ENT] at the first empty line and input a job name.
To quit:
SURVEY screen or COORDINATES screen
ENT
F4
ESC x2
F1
7. REM
Special Function menu F4
007-112
X6
ENT
REM screen
ENT
F1
F3
ENT
MEAS
F1
Select and measure the reference point B by the same procedure as for the point A.
B POINT NUMBER LIST screen
ENT
F1
SELECT
F4
To quit:
REM screen
F5
ENT
X2
B SURVEY screen
B SURVEY screen
MEAS
ENT
F1
8. RESECTION
Special Function menu F4
007-113
X4
ENT
RESECTION menu
F2
RESECTION menu
Note: If you do not need the result saved, just press [ENT] in the STATION POINT screen. ENT
ENT
F1 F4
RESECTION menu
To quit:
RESECTION menu
ESC
Note: To create a new job, press [ENT] at the first empty line and input a job name.
ENT
F4
9. DATA STORAGE
SELECT
007-119
DATA STORAGE menu
move cursor to the input item input the value and ENT
F5
ENT
ENT
ENT
ENT
F1
SELECT
ENT
F1 F4
F4
F5
ENT
X2
A SURVEY screen
Note: To create a new job, press [ENT] at the first empty line and input a job name. After creating a new job, the program automatically proceeds to STATION INPUT screen.
ENT
F4
SELECT
F5
ENT
Note: To input a new station number, press [ENT] at the first "0000" line, and input the number, and then a point description, X, Y, and Z coordinate, and the instrument height:
STATION COORDINATES INPUT screen
F5
F5
ENT
STORE
SURVEY screen
SELECT
F5
F2
Note: Target constant, ppm value, and atmospheric temperature and pressure are automatically applied. If you require measuring and inputting manually, change the instrument settings. Refer to the instruction manual.
ENT
F1 F4
SELECT
input the point number, description, and the prism height -8F1 DISP F3
-9F5
ENT
ENT
MEAS
STORE
F1
F2
SURVEY screen
Note: In this program, there is no separate procedure to measure the backsight point, as the first data saved after the station information is usually considered as that of the backsight point, depending on the post processing program. For the orientation of the horizontal angle, use the function keys on the second function page by pressing F5 [1/2].
POINT NUMBER to over write INPUT screen Note: New survey data cannot be created through keyboard input. The survey data that is automatically obtained by the instrument cannot be edited.
007-200
ENT
F2
X2
ENT
ENT
ENT
F1 F4
Note: To create a new job, press [ENT] at the first empty line and input a job name.
Point selection:
POINT NUMBER INPUT screen
ENT
F1 F4
SELECT
F5
ENT
Note: To input new point information, press [ENT] at the first "0000" line, and input the number, and then a point description, X, Y, and Z coordinate.
X5
ENT
ENT
ENT
F1 F4
Note: To create a new job, press [ENT] at the first empty line and input a job name. Point selection:
Member symbol of the Japan Surveying Instruments Manufacturers Association representing the high quality surveying products.
: : : : : : : : : : : : : : : : :
DataMicrosoftTemplatesNormal.dot
02/10/19 10:35 5 02/10/30 12:41 Kata 443 02/10/30 12:48 8 1,574 () 7,716 ()