Beruflich Dokumente
Kultur Dokumente
configuration in Mach3
Fig.1
Open MACH3 software, select mach3MILL, and then click OK. Please refer to Fig.1
Fig.2
The interface of MACH3 is displayed as Fig.2. The fre uently!used action "uttons are listed on the interface. #e can configure MACH software at first.
Fig.3 $lick PORT & PIN su"!%enu of config %enu. Please refer to Fig.3. Please refer to Fig.&
Fig.& To set up the "asic fre uency within the a"o'e $ircle 1. This para%eter will affect the rotational speed of the %otor. (fter the setup of "asic fre uency, select $ircle 2 where Configuration Scripting will "e defined, please refer to Fig.).
Fig.) To %odify the software settings according to the definition of Parallel *nterface which is detailed in the a"o'e circle.
Fig.+ Then select the output signals colu%n, as shown in Fig.+, and set up the corresponding ite%s per the setup descri"ed in the circle.
Fig.,
Fig.-
Fig.. (fter / $O01 has "een opened, you %ay see the red "utton 21S1T flashing. $lick 21S1T to stop the flashing and then press $3$41ST(2T at the location of $ircle 2
Product Features:
Toshi"a T5+)+6(78 chip ! 7igh power, %a9i%u% 3.)( dri'e current chipset : 1!1;1+ %icrostep setting ! 7igher accuracy and s%oother operation than standard 1, 1;2 step:
(d<usta"le 1.)(!3( dri'e current settings for each a9is ! 2)=,)6=,,)=,166= of full current can "e set for
different stepper %otors O'erload, o'er!current and o'er!te%perature safety ! Full protection for your co%puter and peripheral e uip%ent : On "oard current switching ! Power output can "e set according to specific user re uire%ent : Full closed!type optical isolation to protect the user>s co%puter and e uip%ent 2elay spindle interface ! Outputs Ma9. 3+? ,.)( for spindle %otors or coolant pu%p @only one de'ice can "e powered "y this output:A & channel inputs interface! $an "e used for B3C li%it and e%ergency stop :
Professional design ! Two stage signal processing with super anti! <a%%ing :
5ipolar constant current chopper dri'e with non!resonant region ! $ontrols %otors s%oothly through range without creep effect : Four control inputs @di'ided into pairs of kni'esA ! (llows setting of li%it and e%ergency stop :
Dip settings:
Current Setting 100% 75% 50% 25% 1 ON ON OFF OFF 2 ON OFF ON OFF Decay Mode Settings FAST 25% 50% SLOW 3 ON ON OFF OFF 4 ON OFF ON OFF MicroStep Settings 1 1/2 1/8 1/16 5 ON ON OFF OFF 6 ON OFF OFF ON
* Important Notes:
Power supply 0$ 12!3+? #not inclu$%$& '(oltag% S%l%ction) *+,*-( !C po.%r suppl/ for N%ma *0 st%pp%r motors *-,+1( !C po.%r suppl/ for N%ma +3 st%pp%r motors +1,3-( !C po.%r suppl/ for N%ma 31 st%pp%r motors #High 2oltag% .ill 3urn up th% chips or st%pp%r motors444& 'Amp%rtag% S%l%ction) Output curr%nt of th% po.%r suppl/ can 3% calculat%$ 3/ th% follo.ing %5pr%ssions) Output curr%nt 6 Rat%$ curr%nt of /our st%pp%r motors ' 7uantit/ 8 +A #9or %5ampl%: if /ou .ant to $ri2% 3 ' 3A N%ma +3 st%pp%r motors: th%or%ticall/ +1( **A !C po.%r suppl/ is r%comm%n$%$: 3ut high%r po.%r such as +1( *;A also .ill 3% goo$< If /ou ar% not sur% a3out th% s%l%ction of po.%r suppl/: pl%as% f%%l fr%% to contact us for h%lp& The power output of 12? shall "e applied to the radiator fan of 12? 0ri'er output co%pati"le with 2 or & phase, &,+ or - lead stepper %otors, 3( %a9. Suita"le for unipolar or "ipolar stepper %otors. ?oltage regulated spindle speed controlled "y parallel interface as function of supply 'oltage.
Wiring Diagram:
Simple introductions:
spindle motor
) *na+le
) Dir
) Step
, *na+le
, Dir
, Step
- *na+le
- Dir
- Step
*.pand output !
*.pand output$
$onnection 0iagra%G
4i%it setting FO2 21F121F$1 OF43G @HFoteG you can also ha'e other settings for other applicationsA