Beruflich Dokumente
Kultur Dokumente
Version I?.
WIVZMGI XMQIWXEQTW HIFYK YTXMQI
WIVZMGI XMQIWXEQTW PSK YTXMQI
RS WIVZMGI TEWW[SVHIRGV]TXMSR
LSWXREQI 6SYXIV
MT WYFRIX^IVS
SYXTYX SQMXXIH"
3. Issue the show startup-cong command to display the conguration stored in NVRAM. You have not
saved the conguration, so none can be displayed. Therefore, you should see a 2SRZSPEXMPI
GSRJMKYVEXMSR QIQSV] MW RSX TVIWIRX message.
RouterI=show startup-config
2SRZSPEXMPI GSRJMKYVEXMSR QIQSV] MW RSX TVIWIRX
4. Issue the copy running-cong startup-cong to copy the current active conguration to NVRAM. The
current active conguration is in random access memory (RAM); it should be saved so that the router will
still boot up with the saved conguration in the event of a power outage.
RouterI=copy running-config startup-config
(IWXMREXMSR JMPIREQI ?WXEVXYTGSRJMKA#
&YMPHMRK GSRJMKYVEXMSR
?3/A
3 Boson NetSim Lab Manual
5. Issue the show startup-cong command to show the conguration stored in NVRAM.
RouterI=show startup-config
Current configuration . 8II bytes
Version I?.
WIVZMGI XMQIWXEQTW HIFYK YTXMQI
WIVZMGI XMQIWXEQTW PSK YTXMQI
RS WIVZMGI TEWW[SVHIRGV]TXMSR
LSWXREQI 6SYXIV
MT WYFRIX^IVS
SYXTYX SQMXXIH"
6. If you decide that you would like to start conguring the router from scratch, you can erase the startup
conguration and reload the router. This will enable you to completely delete all congurations on the
router. Issue the erase startup-cong command to delete the conguration le in NVRAM. When
prompted, conrm that you want to erase the NVRAM le system by pressing the Y key.
RouterI=erase startup-config
)VEWMRK XLI RZVEQ JMPIW]WXIQ [MPP VIQSZI EPP JMPIW 'SRXMRYI# ?GSRJMVQA=
?3/A
)VEWI SJ RZVEQ GSQTPIXI
7. Issue the reload command to reload the router, and press Y when prompted to conrm the reload.
When prompted to enter the initial conguration dialog, press N. The initial conguration dialog prompt is
displayed because a startup conguration was not found. The following is sample output from the reload
command:
6SYXIVVIPSEH
4VSGIIH [MXL VIPSEH# ?GSRJMVQA=
&YMPHMRK WMQYPEXIH GSRJMKYVEXMSR
?3/A
Simulated Bootstrap, Version I?., RELEASE SOFTWARE
Copyright (c) I998-?0I? by Boson Systems, Inc.
C?800 Simulated processor with ?0480 Kbytes of main memory
7IPJ HIGSQTVIWWMRK XLI MQEKI
SYXTYX SQMXXIH"
;SYPH ]SY PMOI XS IRXIV XLI MRMXMEP GSRJMKYVEXMSR HMEPSK# ?]IWRSA2
4 Boson NetSim Lab Manual
8. After the router reboots, look at the startup conguration le again. Because you did not save it before
you reloaded, there is nothing there. Therefore, you should see a 2SRZSPEXMPI GSRJMKYVEXMSR
QIQSV] MW RSX TVIWIRX message.
6SYXIV"IREFPI
6SYXIVWLS[ WXEVXYTGSRJMK
2SRZSPEXMPI GSRJMKYVEXMSR QIQSV] MW RSX TVIWIRX
9. Congure the host name of the router as Router1.
6SYXIVGSRJMKYVI XIVQMREP
Router(config)=hostname RouterI
RouterI(config)=exit
6SYXIV
10. Save your router conguration by issuing the copy running-cong startup-cong command.
RouterI=copy running-config startup-config
(IWXMREXMSR JMPIREQI ?WXEVXYTGSRJMKA#
&YMPHMRK GSRJMKYVEXMSR
?3/A
11. Change the host name from Router1 to Boson.
6SYXIVGSRJMKYVI XIVQMREP
RouterI(config)=hostname Boson
&SWSRGSRJMKI\MX
&SWSR
5 Boson NetSim Lab Manual
12. Reload the router by issuing the reload command. Press Y when prompted to conrm the reload. When
prompted to enter the initial conguration dialog, press N.
&SWSRVIPSEH
4VSGIIH [MXL VIPSEH# ?GSRJMVQA=
Simulated Bootstrap, Version S.0, RELEASE SOFTWARE
Copyright (c) I998-?0I? by Boson Systems, Inc.
C?800 Simulated processor with ?0480 Kbytes of main memory
7IPJ HIGSQTVIWWMRK XLI MQEKI ?3/A
&SWSR 3TIVEXMRK 7MQYPEXMSR 7]WXIQ
BOSS (tm) ?800 Simulator (C?800-enterprise), Version S.0, RELEASE SOFTWARE
Copyright (c) I998-?0I? by Boson Software
7MQYPEXIH -QEKI
Boson ?800 (BOSS) emulator (revision S.0) with ?0480K/SI?K simulated memory.
BOSS, Version S.0
? Ethernet/IEEE 80?. interface(s)
? Serial network interface(s)
IK bytes of simulated non-volatile configuration memory.
8I9?K bytes of simulated processor flash (Read/Write)
;SYPH ]SY PMOI XS IRXIV XLI MRMXMEP GSRJMKYVEXMSR HMEPSK# ?]IWRSA2
13. After the router reloads, the host name Router1, not Boson, is displayed at the prompt because the
conguration used to start the router was the startup conguration. Issue the show startup-cong
command to view the conguration used when the router restarted after you issue the reload command.
6SYXIV"IREFPI
RouterI=show startup-config
Current configuration . 8II bytes
Version I?.
WIVZMGI XMQIWXEQTW HIFYK YTXMQI
WIVZMGI XMQIWXEQTW PSK YTXMQI
RS WIVZMGI TEWW[SVHIRGV]TXMSR
LSWXREQI 6SYXIV
MT GIJ
MT WYFRIX^IVS
z136)z
SYXTYX SQMXXIH"
Copyright 19962012 Boson Software, LLC. All rights reserved. NetSim software and documentation are protected by copyright law.