Sie sind auf Seite 1von 10

QUESTIONS ANSWERS

1. 20% to 30%
2. May 40Khz s tanong 20% to less
3. Downlink _______, Uplink ______ 56 kbps and 48 kbps
4. OWF - MUF 80% - 90%
5. DVB-T accurate______ of time 99.99%
6. In ATM, it used when service providers
is not required such as e-mail and data
transfer.
Unspecified-Bit-Rate (UBR)
7. In ATM, used in voice, video, and
distance learning application when
timing is important.
Constant-Bit-Rate (CBR)
8. CAT-6 200 kbps
9. Standard low overheadIP that is used
over packet computer communication
Payload pointer
10. Small divisions Segments
11. OSI Layers 4-7needs Teleservices
12. Not knowing. Bearer Services
13. Additional services Supplementary Services
14. What is used to connect between
central office and when direct trunk is
not available?
Tandem
15. A stacked collinear antenna consisting
of half wave dipoles spaced from one
another by one half wavelength is the
_______.
Broadside Array
16. A Yagi antenna consists _____. A parasitic director and reflector
17. End-Fire Array
18. Used to compensate the handset to the
local loop
Varistor
19. Used in interfacing the handset to the
local loop
Induction Coil
20. For mobile and base station antenna 5/8 lambda
21. One-quarter wavelength A Q-section
22. For VHF and UHF only and cannot be
used for lower frequencies
Collinear Array
23. The highest frequency that can be set
back to earth by the ionosphere, if the
wave is sent vertically upward.
Critical Frequency
24. High proximity RFID tags 2 W
25. Maximum power..AM..in Manila 50 kW
26. Upper frequency MUF
27. New network protocols All of the above (IPv6, Real-Time
Protocol, Resource Reservation
Time?..hehe..)


28. Indirect FM PM
29. It is a channel model in which the input
and output alphabets x and y are
discrete sets and the channel is
memoryless.
The Discrete Memoryless Channel
30. Datagram switching Connectionless Switching
31. Network connection base in Client/server
32. Virtual switching Connection-Oriented Switching
33. First wireless radio transmission Guglielmo Marconi
34. Broad general term for any wireless Radio
35. Store and forward Message switching
36. 1600 Gbps
37. Rate of change in amplitude and
frequency in a filter
Roll-off
38. In communication, it is the altering of
message intentionally or
unintentionally so that it will be
difficult to understand.
Garble
39. Plesiochronous Nearly Synchronous
40. It is the science of measuring light in
the radio spectrum.
Radiometry
41. 11.7 GHz to 12 GHz Ku Band
42. VSAT uses C Band
43. Density is directly proportional to the
____ of .
Gradient
44. There are few major tidal energy
generating powerplants in operation.
The main one is the ______ in Northern
France built in 1966 and has a capacity
of 240 MW.
Ge Rance River
45. Used in data services requiring transfer
of
Variable-bit rate
46. A toll is Used connect different central offices
47. Uses same signaling only Interoffices in the building
48. Difference in SONET and SDH Data rate in multiplexing
49. Factor that greatly affects transmission Phase Distortion
50. Digital DVB System
51. It is a diagnostic application or device
that a network administrator can
purchase and install on a network
workstations or attach to the network
media to monitor and capture data
packets for subsequent analysis.
Sniffer
52. What is network node dedicated to
interfacing between the network and
one or more printers?
Print server


53. The opposite of VCO Discriminator
54. Offers increased dynamic range to that
of JFETs
55. European digital carrier E4 has a
maximum bit rate of _____
139.264 Mbps
56. Assume we need to download text
57. documents at the rate of 100 pages per
58. minute. What is the required bit rate of
the
59. channel?
1.636 Mbps
60. Power crest factor 38 dB
61. Entropy Redundancy
62. node to interconnect any number of
devices/printers
Printer Server
63. Absence of information Entropy
64. Receiver output noise Noise Floor
65. Noise floor is also known as ______. Receiver output noise
66. The measure of degradation of signal to
noise ratio.
Noise Figure
67. TCP/IP Protocol between LAN AND
MAN
Physical Address
68. TCP/IP Protocol like sending e-mails Specific Address
69. Independent on the physical Logical Address
70. MPEG-2 can suppress HDTV data with
a ratio of
55 to 1
71. What is the aspect ration of 35 mm
frame film with dimension of 36x24?
3:2
72. In AM broadcasting, Kung nasan ang
intelligence ng signal?
The difference of the carrier frequency
and the sideband frequency contains the
intelligence of the signal.
73. Measure of data rate Bandwidth
74. Ratio of picture height and bandwidth? Bandwidth Efficiency
75. In LED/LASER, the term used for
bandwidth
Linedwidth
76. Dispersion that occurs with one mode
of propagation
Chromatic Dispersion
77. Caused by temperature inversion? Anomalous Dispersion
78. The dispersion of light in fiber optic
cable caused by a portion of the light
energy traveling in the cladding is
called?
Waveguide Dispersion
79. Not greater than _____ percent by not
less than _____ percent
5, 10
80. Written a book with less than 50 pages,
2 authors
10 CU


81. An AM signal having a carrier
frequency of 940 kHz is to be mixed
with a local oscillator output signal in
order to produce an intermediate
frequency of 455 kHz. At what should
the L.O frequency be set?
1395 kHz
82. The image frequency for a standard
broadcast receiver using a 455 kHz IF
and tuned to a station at 680 kHz would
be
1590 kHz
83. Written a book with more than 100
pages, 2 authors
40 CU
84. Written a book with more than 100
pages, 1 authors
40 CU
85. Doctoral 45 CU
86. Masteral 30 CU
87. Participant 1 CU
88. Facilitator or moderator 2 CU
89. Panellist or reactor 3 CU
90. Speaker in a seminar 5 CU
91. The input to the PLL is in the Phase Detector
92. Which is not one of the three stages in
which a PLL can be operated?
Searching
93. A suite of protocols that allows a wide
variety of computers to share the same
network.
TCP/IP
94. Ratio of peak power factor to the
average power factor
Crest Factor
95. Combination of inductor and capacitor Clapp Oscillator
96. A type of oscillator that is very
commonly used as local oscillator in
superheterodyne radio receiver.
Colpitts Oscillator
97. The Prophet of Integrated Circuit Geoffrey Dummer
98. Pulse equalization Pulse stuffing
99. In TV screen, streak of white. Blip
100. Uses bayonet locking.. Straight-Tip (ST) Connector
101. Designed by Edwin Howard
Armstrong
Autodyne
102. Improvedfrom DFA vacuum tube
amplifier
Autodyne
103. Commonly used sampling rates? All of the above ( 32 kHz, 48 kHz, 44.1
kHz)
104. Heterodyning produces two
frequencies. These frequencies are
called _____.
Heterodynes
105. Emission that operates between 15 35 dB


kHz and 30 kHz must have attenuation
at least _____.
106. 100 to 200 kHz Low Frequency Loran
107. Septate waveguide has ______
septa
One or more
108. Low frequency loran has _____ loran
A
Three or more
109. Advantage of PCM over PAM Noise immunity
110. NTSC frequency allocation of
______ and ______ for 3G
2110 MHz to 2170 MHz and 2010 MHz
to 2025 MHz
111. A folded dipole _____. Has greater bandwidth than half wave
and has a 288 ohms input impedance
112. Characteristic impedance of a
transmission line measured at the
______ when its length is infinity.
Input
113. VT1.5 frame alignment rate 1.728 Mbps
114. STC Band B 734 to 752
115. Make and break pulse dialing 60 milliseconds
116. 770 to 10
6
nm Infrared
117. The area bet the point where the
ground wave ends and first sky wave
returns is called the
Dead zone
118. Maximum coverage Arc of good location
119. Basta 2 times conversion.. Double Conversion
120. Channel 11 of AM broadcasting 621 kHz
121. Channel 288 of FM bradcasting 105.5 MHz
122. SUF amount of ______ per one MHz Php 500, 000
123. 3G minimum biding Php 65 million
124. To ensure that VoIP is distribured Php 1 million
125. Paid up capital for VoIP Php 10 million
126. High power readers RFID Php 300
127. CPE under PRC Executive Order 266
128. Class used for.not less than 1.5
meters above the ground
Class A
129. Audio Class S Amplifier
130. Made up of 8-bit PCM encoded
samples from 16VB
CEPT-E1
131. 1.544Mbps T1
132. 28 kbps
133. Subcarrier frequency of sound in FM 38 kHz
134. Suppressed carrier is also known as
______.
Pilot carrier
135. A grid dip meter measures resonant
frequency of tuned circtuits
Without power being supplied to the
tuned circuit
136. Qualified applicants for 3G 4


137. UTP unshielded twisted pair 7
138. How many different tones in 12-key
tone generator?
7
139. Which is true about carrier in
modulation?
No additional energy is added in the
waveform
140. What is a 56 000 bps dial up modem
standard approved by standard making
organization rather than a single
company? It is likely incompatible with
mode x2 and k56plex?
V.90
141. What standard is an improvement of
the v.90 standard that provides a higher
upstream data transfer rate and also
provides a call waiting service, in
which a users data connection is put on
hold when someone calls the users
telephone number?
V.92 standard
142. Hardware flow control uses _______. RTS and CTS
143. Important/key parameter of ISDN
access or intelligent network access
Signaling
144. A mechanism used by hosts and
gateways to send notification of
datagram problems back to the sender.
ICMP
145. It provides support for newer
applications such as voice over the
internet
SCTP
146. Internet Control Message Protocol
147. A sublayer that defines how different
station can access transmission
medium.
MAC
148. Equal power per octave Pink noise
149. Pink noise has _______. Equal power per octave
150. Central device in star topology Hub/Switch
151. An impedance-matching device that
spread the transmission line as it
approaches the antenna is called a
Delta Match
152. When current increases. Downward Modulation
153. Delay Cell Jitter
154. A problem if different pockets of data
encounter different delays and the
application using the data at the
receiver side is time sensitive.
Jitter
155. Cell Loss Ratio (CLR)
156. Loss of Signal
157. HSDPA is ______. A specific implementation of W-CDMA
158. Network that will fell between LAN CAN


and MAN.
159. 802.3 LAN
160. 802.6 MAN
161. The official name for RS-232C is
_______.
EIA-232D
162. MNP2, MNP3, MNP4, and MNP10
are all _____.
Error correction protocols
163. Cable used for local loops in
telephone system
Twisted pair copper wire

164. According to KBP standards FM
band has how many channels?
100
165. What are the specs of the bell type
103 modem?
300 bps, full duplex, FSK
166. Reference noise level for telephony 1 pW
167. Compared to a standard PCM
systems the quality of the output of a
vocoder is?
Not as good
168. Manchester coding All of the above
169. DS-1 64 kbps
170. What pertains to a person who tries to
pick up someone elses wireless LAN
signals?
War driver
171. What is an action that occurs when a
transmitting or receiving work station
has not received data or a response in a
specified period of time?
Timeout
172. What is the combination of IP address
and TCP port number which is used to
recognize an application on a server?
Socket
173. They are special interest groups that
quickly test, evaluate, and standardize
new technologies.
Forums
174. What is the modern standard for
interconnecting many types of
peripheral devices to computers which
is also a digital interface that uses a
standardize connector (plug) for all
serial and parallel type devices?
Universal Serial Bus (USB)
175. Who designed a switch that comes
before the banyan switch and sorts the
incoming packets according to their
final destination?
K.E Batcher
176. Who coined the term fiber optic? N.S. Kapany
177. What results when the analog
waveform rises or drops to quickly and
the codec my not able to keep up with
Slope Overload Noise


the change?
178. _____ is a secret key encryption
technology that is used in client/server
environments for secure authentication
between computers.
Kerberos
179. What is the project that the computer
society of the IEEE started in 1985 in
order to set standards to enable
intercommunication among equipment
from a variety of manufacturers?
Project 802
180. A padder and trimmer is used for
_____
Tracking
181. Hold the message before processing Queuing
182. Use to establish a point to point
connection across the network.
TCP
183. For long distance communication we
often
184. make use of fibre-optic cable. Which
of the
185. following statements is correct?
Fiber made from glass can be used over
distances of several hundred kilometres.
186. What makes optical fibers immune to
EMI?
They transmit signals in as light rather
than electric current
187. The bipolar transistor can be
controlled by varying the _______.
Dc emitter current
188. Moderate gain, moderate input
impedance, moderate output
impedance.
Common emitter
189. For normal operation, ______is
forward biased and _____is reversed
biased.
Base-emitter connection, base-collector
connection
190. Tactical frequencies Military units
191. The adding of control information on
either of the data text of a block.
Encapsulation
192. In synchronous transmission, _____
is the accepted international standard.
SDH
193. Typical in-channel insertion loss of
DVB-T
.2 dB
194. HSDPA
195. A measure of how fast we can
actually send data through a network.
Throughput
196. DS-1 Bipolar
197. Group messaging IGMS
198. Stalo is a high stable low frequency
oscillator used by a coherent radar for
up converting the transmitted signal of
the ______ and down converting the
Carrier, intermediate


received signal to the ______ signal.
199. Audio part in a video tape 50 Hz to 10 kHz
200. 10% to 120%
201. Allows transmission on the same time
but not between the same network
Full-Full Duplex
202. Number 1 tone frequency 697 Hz and 1209 Hz
203. Number 5 tone frequency 770 Hz and 1336 Hz
204. 20% or less
205. >23 dB across the channel
206. _____ of days 50 %
207. Low tier system High quality, low delay
208. Terrestrial Hierarchical Transmission
209. Station records must be retained at
least _____.
2 years
210. Telautograph Facsimile
211. Changed CCITT into ITU March 1, 1993
212. 3D..produce a depth picture Anti-logarithmic amplifier
213. Metal wrapped around the parabolic
antenna aperture to eliminate side lobes
interfering nearby station is called
______.
Shroud
214. 3D..CRT Acoustic Holography
215. Adaptive coding scheme
216. DS-1 has a frame alignment sampling
(FAS) rate
1 bit
217. New recommendation standard for
unmodulated carrier and empty
information.
N0N
218. Densities 11 30 kA/cm
2

219. Delay of geostationary uplink and
downlink
278 ms
220. Uses (L-R) and (L+R) amplification Kahn-Hazeltine
221. For adaptation and development IEEE
222. What is an impulse commutated
inverter which relies on LC circuit and
on auxiliary thyristor for commutation
in the load circuit
Auxiliary commutated inverter
223. He developed the oldest type of fuel
cells which is the Alkaline Fuel Cells.
Francis Bacon
224. Process-to-process UDP
225. In an FM stereo receiver, what is the
purpose of the 23-53 Khz filter?
To filter out the L-R signal at the output
of the discriminator
226. The square-law relationship of the
FETs input versus output
Minimize cross-modulation
227. The range over which the input to a Dynamic range


receiver or amplifier provides a usable
output is called
228. A loading coil is often used with a
Marconi antenna in orde to
Tune out the capacitive reactance
portion of the input impedance of the
antenna
229. The main problem with the TRF
design is
Lack of sensitivity in receiving all AM
stations
230. DS-1 frame contains 8 bits
231. Cables classified into their Quality
232. Pass all frequencies All-pass filter
233. Class B 10Kw
234. Non-profit EIA
235. Comparing level Level at a time
236. It is the process of extracting a phase-
coherent reference carrier from a
receiver signal.
Carrier Recovery
237. Local office 5
238. The type of radio transmission that
uses pseudorandomly.switched
transmissions is known as
Spread spectrum
239. Large-signal_____
240. Sequence_____
241. A set of communication facilities
allowing direct access to 64kpbs data
streams (or multiples of) for drop and
insert. A form of cell relay, supports B-
ISDN.
Asynchronous transfer mode (ATM)
242. Two mechanicalbsta flow of
currents. . .hehe
Drift and Diffusion
243. 3Damplifier used Anti-logarithmic amplifier




ADDITIONAL...=))

1209Hz 1336Hz 1477Hz 1633Hz
697Hz 1 2 3
770Hz 4 5 6
852Hz 7 8 9
941Hz * 0 #

Das könnte Ihnen auch gefallen