1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in over areas foundation trenches or drains (not exceeding 1.5 min width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2.6.1 All kinds of soil. 3466.08 Cum 123 Extra for every additional lift of 1.5 m or part thereof sor 2.25.1 all kinds of soil 866.52 Cum 23 2 Supplying and filling in plinth with crusher stone dust/ coarse sand under floors including, watering, ramming consolidating in layers not exceeding 20cm in depth in layers not exceeding 20cm in depth and dressing complete. SOR 2.27/7 559.200 Cum 388 3 4.1 Providing and laying in position cement concrete of specified grade excluding centering and shuttering - All worki upto plinth level.4.1.2 With 40mm nominal size graded stone aggregate4.1.2.3 M 7.5 370.300 Cum 2928 4 Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete work including all lift of concrete to si te of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairingstrength and durability as per direction of Engineer-in-charge. M-20 grade reinforced cement concrete by using 403 kg of cement per cum of concrete. All work upto floor II level. SOR I. 5.26 P.08 2239.420 Cum 5014 5 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. SOR 2.24/7 1839.37 Cum 56 6 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding including cost of binding wire up to floor two level including all wastage etc. complete. 5.16.1 Mild steel and Medium Tensile steel bars. 233067.28 Kg 48.0 7 Centering and shuttering including strutting, propping etc. and removal of form work for : 5.9.2 Walls (any thickness) including attached pilasters butteresse s, plinth beams and string courses etc.up to plinth level. 3255.96 Sqm 146 8 6 .2 Brick work with well burnt chimney bricks in bulls patent trench kiln, crushing strength not less than 25kg /sqcm and water absorption not more than 20% in foundation and plinth SOR item 6.2.2/page 27 6.2.2 Cement Mortar 1:6 (1 cement : 6 sand). 714.82 Cum 2519 9 11.25 40 mm thick stone flooring over 20 mm (average)thick base of cement mortar 1:5 (1 cement : 5 sand) including pointing with cement mortar 1:2 (1 cement : 2 sand) with an admixture of pigment to match the shade of stone. Red sand stone / White sand stone 11.25.1 Rough chiseled dressed stone 266.80 Sqm 307 10 Reinforced cement concrete work in beams, suspended floors, roofs having slope of any degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor two level excluding the cost of centering, shuttering, finishing and reinforcement in concrete grade. 5.2.1 M 20 Nomial mix /P-20 47.76 Cum 4442 Revised Estimate Based On MP PWD SOR wef 15 JUNE 2009 & ammended from 11.09.2012 M.P. Police Housing Corpn. Ltd., Ujjain Division, Ujjain Schedule of Items Construction of Barrack at D.R.P.Line, Ujjain 2 S.No ITEM QTY UNIT RATE 11 Reinforced cement concrete work in beams, suspended floors, roofs having slope of any degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor two level excluding the cost of centering, shuttering, finishing and reinforcement in concrete grade. 5.3.1 M 20 Nomial mix /P-20 GROUND FLOOR 498.208 Cum 5014 Add 2 % for lift 50.180 Cum 100.28 12 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding including cost of binding wire up to floor two level including all wastage etc. complete. 5.16.1 Mild steel and Medium Tensile steel bars. Add 1% for lift 52200 Kg 0.48 Add 2 % for lift 5018 Kg 0.96 13 Centering and shuttering including strutting, propping etc. and removal of form for : 5.9.3 Suspended floors, roofs, landings, balconies and access platform. Shelves (Cast in situ) Lintels, beams, beams, girders, bressumers and cantilevers, Columns, Pillars, Posts and Struts Walls in super structure. 9769.76 Sqm 229 14 5.9.4 All types of staircases i/c riser & landings 144.12 Sqm 285 15 Brick work with well burnt chimney bricks in bulls patent trench kiln ,crushing strength not less than 40kg /sqcm and water absorption not more than 15 % in foundation and plinth SOR 6.2.2 Add 2% for lift 94.170 Cum 50.38 16 Half brick masonary with m.s. brick of class designation 25 in superstrucure above plinth level upto floor II .6.11.2 CM (1:4) 1300.80 Sq m 347 17 Extra for providing and placing in position 2 nos 8mmdia. M.S. bars at every course of half brick masonary. 1300.80 Sq m 55 18 Cement plaster in C.M. 1:4 - 12 mm SOR item 13.1.1 page 99 GROUND FLOOR 4651.76 Sqm 92 19 18 mm Cement plaster in two coats SOR item 13.6 5512.76 Sqm 135 20 Cement plaster in C.M. 1:6 - 15 mm SOR item 13.2.2 page 99 3072.00 Sq m 107 21 Kota / cuddapah stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 sand) :11.23.1 - 25 mm thick. Quantity for 2 floors 4358.730 Sqm 771 22 6 mm cement plaster of mix C.M. 1:3 Asper SOR 13.8 Quantity for 2 floors 3425.32 Sqm 79 23 Providing & fixing factory made PVC door frame of size 50x47 mm with a wall thkness of 5 mm mad out of extruded 5 mm rigid PVC foam sheet as per SOR item 9.119 Doors D2 600.00 RM 439 24 30 mm thk. Factory made solid both side pre laminated panel PVC door shutter consisting of frame made out of MS tube of 19 gauge thkness & size 19x19 for styles etc complete as per SOR 9.120.2 Doors D2 201.60 Sqm 2916 3 S.No ITEM QTY UNIT RATE 25 Providing and fixing pressed steel door frames confirming to IS: 4351manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mmthick with mortar guards, lock strike- plate and shock absorbers as specified andapplying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: 10.14.2 Single rebate ( 100 mm x 50 mm) 480.00 RM 380 26 Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorati ve type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 9.21.2 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 249.48 Sqm 1283 27 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 9.62.1 300x16 mm 412 No 107 28 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 9.74.1 250x10 mm S.O.R.P-23 232 No 282 29 Providing and fixing bright finished brass handles with screws etc. complete .9.81.1 125 mm S.O.R.P-23 412 No 122 30 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, all complete as per drawings and the directions of Engineer-in-charge: 21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) 4761.6 Kg 293 31 Providing & fixing glazing in aluminium windows, ventilators & partition etc. as per item no. 10.25.1- With float glass 4 mm thick 476.16 Sqm 743 9.52 Add extra for providing S.S wire gauge of average width of aperture 1.4mm with wire gauge of 0.63mm instead of M.S wire gauge for item 9.27, 9.28, 9.29, 9.30, 9.51 238.08 Sqm 209 32 Filling gap in between aluminium frame & adjecent RSS/brick/stone work by providing weathar silicon sealent over backer rod of approved quality as per SOR 21.6.1 up to 5 mm depth & 5 mm width 1886.4 RM 71 33 Steel work welded in builtup sections for frame work all type sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete: SOR item 10.23 9486.72 Kg 64 34 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing including applying a priming coat of approved steel primer.10.24.1 M.S. tube SOR P.36 7650.0 Kg 81 35 Providing & fixing first quality ceramic glazed wall tiles conforming to IS :15622(6-7 mm thk)of approved make in all coloursshades any size as approved by E-in- chargein skirting, & dados over 12 mm thk bed of cement mortor 1:3 with jointing etc. complete SOR 11.31 4 S.No ITEM QTY UNIT RATE 1688.48 Sqm 629 36 Providing & laying ceramic glazed floor tiles conforming to IS :15622 of approved make in colours shades any size as approved by E-in-chargein skirting, & dados over 12 mm thk bed of cement mortor 1:4 with jointing etc. complete SOR 11.32 248.40 Sqm 848 37 Grading Roof for water proofing treatment with CC 1:2:4 as per SOR 22.14.1 142.680 Cum 3994 38 Grading roof for water proofing treatment with 22.14.2 Cement mortar 1:3 (1 cement : 3 sand) SOR 22.14.2 P/91 24.46 Cum 6450 39 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer ofslurry of cement @0.488 kg/sqm mixed with water proofing cementcompound @0.253 kg/sqm. This layer will be allowed to air cure for 4hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @0 126 kg/sqm This layer will be allowed to air cure for 4 h ours followed with 0.126 sqm. water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints,corners, junctions of pipes and masonry with polymer mixed slurry. ( with five years service gurantee).SOR P.NO.89 I.No.22.5 643.92 Sqm 168 40 Providing and applyoing JK or Birla or equivalent wall care exterior or interior mix putty for outer surfaces i/c sand papering for making the surface smooth for applying any paint with all cost of material and labour and scaffolding etc. in all positions complete item no. 13.7 page 106 inclusive of ceiling area qty same as inner plaster + ceiling 11151.32 Sqm 95 41 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade 13.30.1 New work (two or more coats) over and including priming coat with cement primer sor 13.30.1 p-49 qty same as inner plaster 7725.76 sqm 52 42 13.35 Finishing walls with Acrylic mooth exterior +paint of required shade: 13.35.1 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm). qty same as outer plaster 5512 sqm 68 43 10.17 Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs, beams during laying including painting the exposed portion of loop, all as per standard design complete. 300 no. 87 44 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp of internal dia 140mm, 73mm height,top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3mm dia. round headed screws, one lock at the corners. Clamp shall be made of 12mm dia M.S. bar bent to shape as per standard drawing.SOR P.NO.35 I.NO. 10.18 300 No 140 45 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: 13.50.1 Two or more coats on new work over an under coat of suitable shade with ordinary paint of pproved brand and manufactureSOR item 13.50.1/50 1178.64 Sqm 64 INTERNAL WATER SUPPLY & SANITARY 5 S.No ITEM QTY UNIT RATE 1 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting & making good the walls and floors wherever required : S.O,R.P-133/It.No.17.2.1 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid 24.00 Each 2657.00 2 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : S.O.R.P-133/It.No.17.1.1 17.1.1 White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests. 48.00 Each 2838.00 3 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass wa ste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Flat back wash basin size 550x400mm with single 15 mm C.P. brass pillar taps. S.O.R.P-134/It.No.17.7.4 17.7.4) White Vitreous China Flat back wash basin size 550x400mm with single 15 mm C.P. brass pillar tap. 48.00 Each 1356.00 4 Providing and fixing Stainless Steel ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and 40 mm stainless steel plug including painting of fittings and brackets, cutting and making good the walls wherever required : S.O.R.P-136/It.No.17.10.1.1 17.10.1.3) Kitchen sink with drain board 17.10.1.1 510x1040 mm bowl depth 200mm. 8.00 Each 4041.00 5 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. SOR P/291 I/18.7.1,2,3 Internal work Exposed on wall. 18.10.1) 15 mm dia. nominal bore 800.00 R.M. 98.00 18.10.2) 20 mm dia. nominal bore 1000.00 R.M. 116.00 18.10.3) 25 mm dia. nominal bore 100.00 R.M. 150.00 6 Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : S.O.R.P-154/It.No.18.13 18.13.1) 25 to 40 mm nominal bore 8.00 Each 191.00 7 Providing and fixing C.P. brass pillar cock approved quality and make conforming to IS:specification. 15 mm nominal bore 125 mm long foam flow. S.O.R.P-162/It.No.18.54 48.00 Each 576.00 8 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. S.O.R.P- 161/It.No.18.51.1 18.51.1 )15 mm nominal bore . 80.00 Each 363.00 9 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore. S.O.R.P-161/It.No.18.53.1 6 S.No ITEM QTY UNIT RATE 18.53.1 15mm nominal bore 120.00 Each 400.00 10 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : S.O.R.P-155/It.No.18.22.1 18.22.1) 100 mm diameter 60.00 Each 518.00 11 Providing and fixing brass stop cock of approved quality : S.O.R.P- 154/It.No.18.16.1,2 60.00 Each 221.00 12 Providing and fixing gun metal gate valve with C.I. wheel of 18.16.1 15 mm nominal bore 0.40kg 18.16.2 20 mm nominal bore 0.75kg approved quality (screwed end) : S.O.R.P-154/It.No.18.17.2,3 18.17.3) 25 mm nominal bore 16.00 Each 329.00 13 Providing and fixing square-mouth S.W. gully trap grade 'A' complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : With Modular Bricks class designation 40. S.O.R.P- 170/It.No.19.4.2 19.4.2) 150 x 100 mm size P type. 16.00 Each 1106.00 14 Supplying and fixing C.I. cover 300x300mm without frame for gully trap(standard pattern( the weight of cover to be not less than 4.50 Kg. S.O.R.P-170/It.No.19.2 16.00 Each 236.00 15 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement :2 sand:4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. : S.O.R.P-139/It.No.17.37.1,2 17.37.1) For 100 mm dia. Pipe 80.00 Each 82.00 17.37.2) For 75 mm dia. Pipe 80.00 Each 79.00 16 Providing and fixing on wall face unplasticised Rigid PVC Rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.for soil and wast pipes Single socketed pipes for working pressure of 4 kg./cm2 S.O.R.P- 145/It.No.17.74.3 17.74.1 75 mm diameter 440.00 R.M. 156.00 17.74.3) 110 mm diameter 600.00 R.M. 259.00 17 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. S.O.R.P-/It.No.17.28 Semi rigid pipe 32 mm dia 56 each 67.00 18 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for nplasticised Rigid PVC Rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion.S.O.R.P-/It.No.17.75 Coupler 75 mm 168 each 183.00 110 mm 72 each 245.00 Single tee with door 75x75x75 mm 88 each 308.00 110x110x110 mm 88 each 459.00 Bend 87.5 75 mm bend 104 each 163.00 110 mm bend 104 each 259.00 Shoe 75 mm Shoe 104 each 277.00 7 S.No ITEM QTY UNIT RATE 17. 75.6.3 110 mm Shoe 104 each 485.00 EXTERNAL SANITARY WATER SUPPLY 1 Providing and laying below ground unplasticised PVC pipe to with stand working pressure of 4 kg/cm2 soild waste pipes confirming to IS:13592 and IS:4985 including jointing with seal ring confirming to IS :5282 leaving 10mm gap for thermal expansion all necessary fittings etc. complete. SOR I.No.19.35.1,2,3 P.84 19.35.2 160 mm diameter OD 175.00 Rm 450.00 2 Providing and laying cement concrete 1:5:10 (1 cement : 5 sand : 10 graded stone aggregate 40 mm nominal size) all-round PVC. pipes including bed concrete as per standard design: SOR I.No.19.36.1,2,3 P.84 19.36.2 150 mm diameter PVC. pipe 175.00 Rm 466.00 3 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 sand ) R.C.C. top slab with 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal standard design : With modular bricks with class designation 40 19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : SOR P.No. 81 I.No. 19.7.1 20.00 each 5293.00 4 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work SOR I.No. 18.12.5 P. 71 18.12.5 40 mm dia. nominal bore 300.00 Rm 293.00 SOR I.No. 18.12.3 P. 71 SOR I.No. 18.12.6 P. 71 50.00 Rm 459.00 5 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : SOR I.No.18.17.5 P. 71 18.17.5 40 mm nominal bore 6.00 each 459.00 18.17.6 50 mm nominal bore 4.00 each 665.00 6 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 20.00 each 1015.00 19.19.1.1 Rectangular shape 600x450mm internal dimensions SOR I.No. 19.19.1.1 P. DEVELOPMENT WORK 1 Excavation for roadway in soil including loading in truck for carrying of cut earth to embankment site with all lifts and lead upto1000 metres and as per relevant clauses of section-300 SOR P.No. 5 I.No. 3.1 90.00 cum 122.00 8 S.No ITEM QTY UNIT RATE 2 By Mix in Place Method (Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) (ii) for grading- II Material SOR P.NO.18 I.NO. 4.1B(ii) 90.00 cum 541.00 3 Dry Lean Cement Concrete Sub- base (Construction of dry lean cement concrete Subbase over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing.) SOR P.NO. 26 I.NO. 6.1 32.00 cum 2383.00 4 Cement Concrete Pavement (Construction of un-reinforced, dowel jointed, plain cement concrete pavement M-40 grade concrete over a prepared sub base with cement , coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, admixtures as approved, curing compound, finishing to lines and grades as per drawing as per IRC 15 2011 and as per relevant clauses of section SOR P.No. 15 I.No.6.3 59.20 cum 5847.00 5 Construction of Shoulders with approved material/selected soil i/c excavation all lifts & leads i/c grading to required slope & camber of 4% and compacting using vibratory roller of 80 to 100 kN static weight to meet requirement as per relevant clause of 400. B Hard Shoulders (CBR value >12) SOR P.NO. 19 I.NO. 4.15 B 100.00 cum 223.00 SOR P.No. 4 I.No. 4.1.2.3 6 Providing and laying in position specified grade of reinforced cement concrete (with 20mm nominal size graded stone aggregate) excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 5.1.1 M 20 Nominal mix SOR P.No. 6 I.No. 5.1.1 43.07 cum 4526.00 7 Centering and shuttering including strutting, propping etc. and removal of form for : SOR P.No. 6 I.No. 5.9.3 9 S.No ITEM QTY UNIT RATE 5.9.2 Walls (any thickness) including attached pilasters butteresse s, plinth beams and string courses etc.up to plinth level. 246.36 sqm 222.00 8 12 mm cement plaster 1:3 (1 cement: 3 sand) finished with a floating coat of neat cement. SOR P.No. 47 I.No. 13.4 236.43 sqm 139.00 9 13.13 Extra for providing and mixing water proofing material in cement plaster work in proportion recomended by the manufacturers. For each bag of 50 kg cement used in the mix SOR P.No. 48 I.No. 13.13 4.00 each 52.00 10 Cement concrete flooring 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.(Area of panels not exceeding 2 sqm) SOR P.No. 37 I.No. 11.1.1 11.1.1 40mm thick with 20mm nominal size stone aggregate. 56.94 sqm 239.00 11 Providing and fixing on wall face unplasticised Rigid PVC Rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.for soil and wast pipes Single socketed pipes for working pressure of 4 kg./cm2 17.74.3 110 mm diameter (SOR P-68 I/17.74.3) 3.00 Rm 259.00 INTERNAL ELECTRICAL WORK 1 Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI Marked of suitable size and 1.5 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit including painting etc. as required as per specification for :- Using Modular Accessori es 4.1 4.1 Light Point/Fan Points. a) Short point 210 Each 275 b) Medium point 400 Each 438 c) Long point 200 Each 630 4.2 4.2 3 Pin 6 Amp socket outlet on Separate Board a) Short point 80 Each 345 b) Medium point 104 Each 558 4.3 4.3 Call Bell / Buzzer Points c) Long point 16 Each 636 4.4 4.4 Twin Control light points c) Long point 40 Each 739 2 Point wiring (excluding metallic switch box & sheet but including switches, sockets) for 3 pin 6 Amp. Socket outlet point with 1 .5 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit with required materials as per specification on same board . SOR 4.5 120 Each 219 10 S.No ITEM QTY UNIT RATE 3 Point wiring (excluding metallic switch box & sheet ) for 3 Pin 16 Amp. Socket Outlet Point With 4 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISI marked in Concealed rigid P.V.C.Conduit (HMS) ISI Marked of suitable size including painting etc. with 16 Amp. F.T. Switch & Socket / S.S.Combined 16 Amp. of ISI Marked and 4 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit as per specification for :- 9.1 Using Modular Accessori es On Separate Board B. Medium Point 20 Each 767 C. Long Point 20 Each 1146 D. Extra Long -I 20 Each 1626 4 Supplying and fixing PVC conduit ISI marked alongwith the accessories in concealed system including painting etc. as required SOR 16.2 PVC . Conduit 25 mm (HMS) 600 Metre 35 5 Supplying and fixing of approved make modular type metal box with modular frame/ base plate and cover plate including fixing in concealed / surface excluding switch, socket etc. as required for:- 17.2 1 Or 2 Module 80 Each 53 3 Module 80 Each 65 4 Module 200 Each 74 6 Module 200 Each 112 8 Module 40 Each 149 6 Supplying and drawing single core PVC insulated cable FR with copper multi strand conductor ISI marked in existing rigid conduit in surface or concealed as per specification. SOR 4.6 1x1.5 sq mm for inverter 2000 Metre 14 2 X 2.5 sq mm 1600 Metre 20 Wiring for circuit wiring with PVC insulated cable FR with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) of ISI marked suitable size including painting etc. as required as per specification a) 2x2.5 Sq.mm. 2643 Metre 71 b) 4x2.5 Sq.mm. 200 Metre 109 7 Supplying of ISI Marked and accepted standard of Miniature Circuit Breaker (MCB) of 'C' series suitable for 240/415 Volts, 50 Cycle , 10 kA Value AC supply confirming to IS : 8828 : 1996, IEC : 60898 :2002 but without enclosures :- SOR 24.3 6 Amp to 32 Amp Rating SP 120 Each 126 6 Amp to 32 Amp Rating TPN 8 Each 822 8 Supplying of approved make TPN MCB DB Metal Double Door with provision for FP MCB/lsolator/RCCB/RCBO as incomer and SP MCBs as outgoing inclusive of Busbar, Neutral bar, Earth bar & two earth terminals etc. complete as per IS:13032( exclusive of MCB & isolator ): SOR 24.6 8Way 8 Each 2492 10 Fixing of MCB / Isolator SP/DP in sheet steel enclosure as required as per accepted practice, including mounting on busbar and cable connection etc. complete (Labour only ) SOR 25.4 120 Each 2 11 Labour charges for fixing sheet steel enclosure, MCB DB surface mounting type, as per accepted practice on 25x5mm flat iron clamps duly embedded in wall, cable connection etc. complete. 8 Each 53 12 suppling and drawing following pair,0.5 Sq mm PVC Insulated copper conductor unarmoured telephone cable in existing surface / concealed , steel / PVC Conduit as required. SOR 26.2 (ii) 2 Pair 200 Metre 19 13 Suppling and drawing Co-axial T.V. Cable RG-6 Grade , 0.7 mm Solid Copper conductor PE Insulated , Shielded with fine tined copper braid and protected with PVC Sheath in the existing surface / concealed , steel / PVC. Conduit as required. 600 Metre 23 14 Supplying and fixing as per specification Bulk Head fitting of approved make suitable for 100 Watt lamp with necessary materials complete. 11 S.No ITEM QTY UNIT RATE Ordinary 40 Each 65 15 Supplying and fixing as per specification Caution / Danger Board as required of approved make & design with necessary material complete. Small Size 8 Each 80 16 Supplying & fixing of approved make industrial type metal plug & socket DBs (without MCB) SPN sheet enclosur inclusive of 2 pole & earth metal plug complete as per specification SOR 24.9.2 24 Each 568 17 Supplying & fixing as per specification call bell/buzzer of approved make with necessary materials complete SOR 26.4.2 Dingdong bell 16 Each 90 18 Supply, fixing & testing Flourescent Tube rod ISI marked of approved make as required as per specification SOR 26.18.2 - 4 feetx36 Watt 320 Each 41 19 Supply, fixing & testing Flourescent CFL ISI marked of approved make as required as per specification SOR 26.20.3 - 250 Watt 320 Each 135 20 Suppling and fixing of approved make step type Modular electronic, Fan regulator including connection etc. as required on existing board 26.31.1 450 Watt 200 Each 249 21 Supplying & fixing & testing of approved make electric ceiling Fan of double ball bearing complete with standerd accessories A.C. 230-250 Volts including connection etc. as required as per IS 374/1979 & ammendments complete SOR 26.29.1 Ceiling Fan Energy saver 50 W 1200 mm sweep 200 Each 1440 22 Supplying & fixing & testing of approved make Exhaust Fan of heavy duty complete with mounting frame, anchor fasteners etc. A.C. 230-250 Volts including connection etc. as required complete SOR 26.36.1 80 Each 2481 23 Supply, fixing & testing Flourescent Tube fitting ISI marked of approved make as required as per specification SOR 26.39 - 320 Each 490 24 Wiring for sub-mains with PVC insulated cable FR with copper multi strand conductor ISI marked in recessed / concealed rigid steel ISI marked conduit of suitable size(Conduit included) including connection painting etc ,as required as per specification 4 WIRE SUB-MAIN 20.4.3 6.0 sq mm cable in 25 mm conduit 160 Metre 219 25 Supply and Installation of TV socket co-axial with cover plate 80 Each 206 26 Supply and Installation of RJ 11 telephone socket (jack type) with cover plate 80 Each 204 27 Supplying, fixing.testing & commissioning wall / floor mounted LT Panel primer coated with two coat of enamel paint & provided with required gasket for dust/ vermin proof with degree of protection IP42 suitable for 415V 3 phase ,50 Hz ,4 wire systemfabricated out of CRCA sheet upto 2 mmthick (1 .6 mmfor doors) with frame work of angle iron/ channel/ bolted type construction duly compartmentalised for incomer.bus section , outgoings .cable alleys & CT,PT Ampere Meter ,Volt Meter , selector switches, Frequency Meter .phase indicating lamps , energy Meter complete including cost of busbar supports.detachable cable gland plates,2 earthing terminals, internal wiring & fixing of separately supplied MCBs, MCCBs .panel mounted Changeover switch/SFUs, etc. as required but excluding cost of busbar strips.Ampere Meter, Volt Meter, Selector switch as per approved design & specification 200 Kg 95 28 Supplying and fixing heavy duty cable gland for P.V.C. insulated armoured cable with brass washer, Rubber ring complete erected with cable and lead connection etc. as per specification complete. SOR 33.6 Gland Size 22mm suitable for cable 2,3,3!4 & 4 x upto 6 Sq.mm 2 Each 29 29 Copper Lugs Pin Type SOR 33.9 a. Upto 25 Sq.mm Conductor Size 100 Each 9 30 Supplying of metal clad ISI Marked busbar chamber made of heavy gauge iron sheet complete with copper strip and busbar supports as per specification confirming to IS -4064 23.6 400 AMP 440/500 VOLTS, 4 way 1 Each 3626 23.6 100 AMP 440/500 VOLTS, 4 way 12 S.No ITEM QTY UNIT RATE 31 Supplying of ISI Marked and approved make of Moulded Case Circuit Breaker (MCCB) suitable for 3 phase,3 pole, 50 Hz, 415 Volts, AC supply with respective interrupting capacity (KA) at 415 Volts cited against their range standard conforming to IS - 8828 24.1.1.4 Current Rating -200 Amps & 70% -100% adjustable 1 Each 7800 24.1.1. Current Rating -100 Amps & 70% -100% adjustable 8 Each 4082 32 32.3 Earthing with G.I. Earth plate 600mm X 600mm X 6mm thick including accessories and providing masonary encloser in cement mortor, cover plate having locking arrangment on the top and G.I. watering pipe 20mm dia 2.7 Metre long etc. (but without charcoal or coke and salt ) complete as required. 2 Each 2200 33 32.5 Add Extra for using salt and charcoal / coke for G.I. Plate or Copper plate earth electrode as required including excavation & refilling. 2 Each 472 34 33.1 Supply of XLPE Insulated power cable (conforming IS-7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554- 1100 Volts grade , 2 core /3 core/4 coreISI MARKED with Alu. Stranded /solid conductor 33.1.6 ARMOURED 3 CORE 33.1.7.5 150 Sq.mm.(XLPE) 80 Mtr 886 35 33.13.21 Laying of underground cable armoured./ unarmoured as per specification in air with approved type of iron clamps complete. 33.13.21.2 3 / 3 / 4 Core cable 150 Sq.mm above 80 Mtr 34 36 Supplying of ISI Marked Change over switches in sheet encloser confirming to IS : 4064 / IS : 13947 (part I & III ) with side handle operated 4 pole with two earthing terminals 22.3.5 200 Amps. 415/500 Volts.( off load ) 1 Each 11089 Sub-Engineer M.P.Police Housing Corpn.Ltd. Ujjain Division, Ujjain Asstt. Engineer M.P.Police Housing Corpn.Ltd. Ujjain Division, Ujjain Project Engineer M.P.Police Housing Corpn.Ltd. Ujjain Division, Ujjain