1 INTRODUCTION 1.1 Unpacking 2 1.2 LED Indicators 2 1.3 Performance features 3 2 INSTALLATION 2.1 Advert 4 2.2 Connect and Communication. 4 2.3 Connect mode and Transfers distance 4 3 EXCURSUS
1 INTRODUCTION 1.1 Unpacking One TER850S/860S Fast Ethernet Converter One DC power The Users Guide Inspect the Converter and all accompanying items, if any item is damaged or missing, report the problem to you TER850S/860S dealer immediately.
1.2 LED Indicators The LED indicators of the Converter include PowerLinkDUPFX-Link and FX-TX. The LED indicators are used to facilitate monitoring and troubleshooting of the Converter. The following shows the LED indicators for the Converter along whit explanation of each indicator. LED indicator Color State Explain Red Light This indication operates when the Converter is turned on Power
Extingu ish If this indicator is not lit, check the AC power connector to ensure proper insertion of the power cord and that the power switch is turned on. LINK Green Light The port link to network DUP Green Light The port work in full duplex FX-LINK Green Light The SC port link to network Green Flicker Link on the head transfer data at the fiber 2 3 1.3 Performance features Generally features Criterion IEEE802.3 10BASE-T Ethernet IEEE802.3 frame typeTranslucent Protocol CSMA/CD Data transfer Rate
Ethernet 10Mbps 100Mbps Network Twisted-pair 10BASE-T: 2-pair UTP Cat3, 4,5(100m) EIA/TIA-568 100-ohm STP (100m) Number or Port 8 10BASE ports Environmental and Physics DC output 7.5-9V/1A Circulate Tempera-true 0C~65C Storage Tempera-true 0C~80C Humidity 5%~90% no coagulate Emissions FCC Class ACE Mark Class AVCCI Class ABSMI Class A C-Tick Class A
4 2.1 Advert 2 INSTALLATIONS The surface of 3Kg can bear a heavy burden at least. Convenience receptacle and equipment should be within 1.82 meters. Check power supply is confirmed the safe connection. Affirms to have the ventilation that is enough, can be very good dissipates heat. Not lay up the heavy object on Converter 2.2 Connect and Communication 1. Link the network equipment to take 10/100BASE-TX interface to the RJ45 hub of TER850S/860S by way of the UTP. 2. Link the equipment to take 10/100BASE-FX interface to the SC fiber connection head of TER850S/860S by way of the multimode fiber thread. 3. Link AC/DC power supply changeover ware to the DC power receptacle of TER850S/860S. The communication distance of maximum likelihood is 2100 meters of s between two equipments hypo graph displays (TER860S attainability is 20100 meters). NOTICEThe network interface of two equipments must be defined sets up the optical fiber at the full duplex model permitted more than 2000 meters of the use. UTD 100M(max) Multimade 2,000M(max) 10/100BASE-TX Port 100BASE-FX Port
Picture 2.2.1 Connect and Communication mode 2.3 Connect mode and Transfers distance Y X
Picture 2.3.1 Device A attended mode of fiber connection head Connect mode and transfers distance corresponding table 1 Mode Device A Device B X Y Full duplex DTE DTE* 2000 M 100 M Half duplex DTE DTE Y100X+Y300 Half duplex DTE Class I Hub ( + ) Y100X+Y75 Half duplex DTE Class II Hub ( + ) Y100X+Y118 Y X Z
Picture 2.3.2 Device A No attended mode of fiber connection head Connect mode and transfers distance corresponding table 2 Mode Device A Device B X Y Z Full duplex DTE DTE* 100 M 2000 M 100 M Half duplex DTE DTE X300X+Y+Z230Z100 Explain DTEData Terminal EquipmentServerworkstationswitchRouter or other terminal equipment. 5 If Device B is one 100BASE-TX Switch UTP is 100 meters by it to the distance of equipment except TER850S/ 860S.
3 Excursus RJ-45 pinouts criterion when cascading or connecting the Converter to anther Converter ,or to a switch or bridge,through a UTP prot,a modified crossover cable is necessary. Please pay attention to the cable that these products mate . What the following diagram was showed is that standard RJ-45's Converter reaches the definition drawing the foot with linking the head . 6
Standard RJ-45 Converter / links head
Standard 3 grades of cables RJ-45 pinouts criterion Straight Twisted-Pair Cable Pinouts contact Media Direct Interface Signal 1 Tx + (transmit) 2 Tx - (transmit ) 3 Rx + (receive) 4 Not used 5 Not used 6 Rx - (receive) 7 Not used 8 Not used 1 2 3 4 5 6 7 8 8 7 6 5 4 3 1