Beruflich Dokumente
Kultur Dokumente
FINAL REPORT
REPORT NO.: PGS/SI/2013/CLJOC/06/SV-6X/FR
(REV 1.0 15 JULY 2013)
TO
CUULONG JOINT OPERATING
COMPANY (CLJOC)
FOR
SOIL BORING AT
BH SV-6X
BLOCK 15-1
OFFSHORE VIETNAM
Prepared by:
PTSC GEOS & SUBSEA SERVICES COMPANY LIMITED/
ASIAN GEOS SDN. BHD.
th
CONTENTS
Page
SUMMARY
1.0
2.0
INTRODUCTION
1.1
Scope of Work
FIELD INVESTIGATION
2.1
Site Organization
2.2
2.3
2.5
3.0
LABORATORY TESTING
4.0
SUBSOIL CONDITIONS
5.0
DESIGN PROFILE
5.1
Submerged Density
5.2
5.3
Granular Soils
11
5.4
State of Consolidation
12
5.5
Sensitivity
12
6.0
14
6.1
Computation Methods
15
6.2
Limiting Values
15
6.3
16
7.0
17
8.0
18
9.0
19
9.1
19
9.2
Sliding Stability
20
10.0
PILE INSTALLATION
21
10.1
21
Estimation of SRD
10.2
22
10.3
22
10.4
22
10.5
23
10.6
Self Penetration
24
10.7
25
11.0
LIST OF REFERENCES
26
12.0
LIST OF PLATES
27
SUMMARY
CUU LONG JOINT OPERATING COMPANY (CLJOC) awarded the contract to PTSC Geos &
Subsea Services Co., Ltd (PTSC G&S) and for offshore geotechnical investigation services at Block
15-1 Field, Offshore Vietnam, Vietnam.
PTSC G&C and PTSC G&Cs sub-contractor Asian Geos Sdn. Bhd. (AGSB) performed the site
investigation from the geotechnical vessel MV PTSC Surveyor. This 4-point mooring vessel is
equipped with a geotechnical equipment spread consisting of a Top Drive Motion Compensated
drilling rig system, in situ CPTU system, and a field laboratory.
This report presents the final documentation of the soil investigation works performed at BH SV6X, Block 15-1 Offshore Vietnam, Vietnam. Fieldwork was performed from 17th April 2013 to 19th
April 2013 with one (1) alternate 140m sampling and CPTU hole.
The actual coordinates and water depth of the borehole are tabulated as below:
Location
Latitude
BH SV-6X
Coordinates
WGS 84
Longitude
Easting
Water Depth
Northing
Results from alternate sampling and CPTU tests indicated that the subsoil encountered at BH SV6X location comprises generally alternating layers of clay, silt and sand until the final depth of
penetration.
Results of field laboratory testing for the borehole are summarized in the Summary Boring on the
Plate 12.
In the selection of the design parameters, higher weightage was given to the results from UU
triaxial test and CPTU data. Design profiles were selected as discussed in Section 5.0 for the
location and as shown on Plate 5. The shear strengths were deduced from CPTU results with
adopted cone factor Nkt of about 20 to 25 (30m to 132.8m) and 25 to 28 (134m to 139.8m). The
clays can be classified as normally consolidated to over-consolidated.
Ultimate axial pile capacity curves were computed based on the recommendations by API RP 2A
(2000) Method. The results are presented on Plates 15a to 15d for the 762mm (30-in), 914mm
(36-in) diameter conductors and 1219mm (48-in) diameter piles for this location. A factor of safety
of 2.0 is considered appropriate for normal operating loads and factor of safety of 1.5 should be
used with respect to maximum storm loads.
Lateral soil resistance versus pile deflection (P-Y) data for corresponding piles were generated
and tabulated on Plates 17a to 17i. The P-Y data developed for this study is applicable to single
and isolated pile subjected to repeated lateral load and is presented for cyclic loading condition.
The value of the neutral penetration (Xr) was determined to be in the range of 10m to 15m for this
location.
The mobilized values of skin friction and end bearing as a function of axial pile displacement (T-Z
and Q-Z) were developed and tabulated on Plates 18a to 18l and 19a to 19p respectively. The Tresidual value was taken as 90% of the peak based on UU results and local experience. The
quake value (Zmax) at T-peak value is assumed to be 1% of pile diameter for clay, which is in
accordance to the recommendation by the API RP 2A (2000). The quake value (Zmax) at Q-peak
value is assumed to be 10% of pile diameter.
Computation of mud mat bearing capacity is discussed in Section 9.0 herein. A factor of safety of
2 is recommended to be applied to determine the mat area. Result of the pile installation study is
discussed in Section 10.0 herein.
Two (2) conductor and one (1) pile diameters were selected for the driveability analysis, namely
the 762mm (30-in) and 914mm (36-in) diameter conductors and the 1219mm (48-in) diameter
pile. Two (2) hammer types considered were the IHC S280 and IHC S750 hammers at 90%
efficiency.
ii
1.0
INTRODUCTION
CUU LONG JOINT OPERATING COMPANY (CLJOC) awarded the contract to PTSC GEOS &
SUBSEA Services CO., LTD. for offshore soil investigation services at Block 15-1 Field,
Offshore Vietnam, Vietam.
PTSC G&C and PTSC G&Cs sub-contractor Asian Geos Sdn. Bhd. (AGSB) performed the site
investigation from the geotechnical vessel MV PTSC Surveyor. This 4-point mooring vessel is
equipped with a geotechnical equipment spread consisting of a Top Drive Motion Compensated
drilling rig system, in situ CPTU system, and a field laboratory.
The general purpose of the investigation was to collect geotechnical data for the assessment of
the proposed platform foundation at BH SV-6X, Block 15-1, Offshore Vietnam, Vietnam.
This report specifically presents the final documentation of the soil investigation works
performed at SV-6X, Block 15-1, Offshore Vietnam, Vietnam. Fieldwork was performed from
17th April 2013 to 19th April 2013 for the sampling and CPTU.
1.1
Scope of Work
Provide complete marine spread, i.e. vessel, drilling rig, in situ testing equipment and
field laboratory;
b)
c)
Perform drilling, sampling, down-hole cone penetration test with pore pressure
measurement (CPTU), field laboratory tests and preliminary field engineering analyses
onboard;one (1) alternate 140m sampling and CPTU hole.
d)
Carry out additional laboratory testing onshore and engineering analyses pertaining to
the proposed foundation including consolidation test at every soil layer up to 20m depth.
e)
Submit field, factual and engineering reports to present the results of the fieldwork and
engineering analyses:
f)
Final corrected location of all sampling and in-situ CPTU testing points, with a
location map and WGS84 coordinates in the reference system,
ii)
Final corrected water depth records, with the reference level and tidal variations,
iii)
iv)
Summary graphs of the soil parameters required for piled foundation analysis
design purposes,
v)
Design of pile foundations (for two (2) conductor diameters namely 762mm (30inch), 914mm (36-inch) and one (1) pile diameter namely 1219mm (48-inch)),
1
including unit skin friction and end bearing resistance, ultimate axial pile capacity
under compression and tension loading, vertical and lateral load-displacement
behaviour (P-Y and T-Z/Q-Z curves) under and cyclic loading conditions,
vi)
vii)
For pile design, the contractor shall apply their recommended design methodology, but will also
apply in cohesive material using the current API RP2A (2000) method.
.
2.0
FIELD INVESTIGATION
The MV PTSC Surveyor sailed from Vung Tau to Block 15-1 on 17th April 2013 and arrived at SV6X location on the same day. The vessel was then positioned at BH SV-6X location to allow for
soil boring to commence.
The fieldworks were carried out from 17th to 19th April 2013 with one (1) alternate 140m sampling
and CPTU hole.
Continuous soil sampling was carried out to the first 30 metres, then followed by a cycle of 3-m
stroke CPTU and continuous 1-m soil sampling interval to termination depth of 140.0m.
2.1
Site Organization
For this soil investigation campaign, PTSC G&S and AGSBs operational organization is as
follows:
Company Site Representative
Geotechnical Engineer
Drilling Supervisor
: Zainuddin Hassan
2.2
Positioning was carried out using the Starfix HP DGPS system. The equipment was mobilized
and deployed on the MV PTSC Surveyor. All coordinates were located based on the following
geodetic parameters:
Table 1 - Geodetic Parameters
PROJECTION SYSTEM
Name
: WGS84
Projection Type
Unit of Coordinate
: Meters
Central Meridian
Zone no.
Latitude of Origin
: 00 00 00.000N
Longitude of Origin
: 105 00 00.000E
False Easting
: 500 000m
False Northing
: 0m
: 0.9996
Datum
Datum Name
: WGS-84
ELLIPSOID
Ellipsoid Name
: WGS-84
: 6378137.000m
: 6356752.3142m
: 298.25722
Eccentricity (e )
: 0.9996
: WGS-84 to WGS-84
DX
= 0.0m
DY
= 0.0m
DZ
= 0.0m
The positioning of the drill string over the proposed location was achieved using real time DGPS
with a minimum of four satellites giving a three-dimensional fix. The actual coordinates of the
sampling and CPTU holes are listed as below:
Table 2 - Boring Coordinates
Coordinates (WGS 84)
Location
Latitude
BH SV-6X
Longitude
1020'22.426"N 10818'32.451"E
Easting
862 460.08m
Northing
1 144836.27m
2.3
Once the vessel was anchored on location, initial water depth was measured by using the
vessels echo sounder (model Odom EchoTrac MKIII) which had been calibrated at Vung
Tau,Vietnam. The water depth was checked and confirmed by means of drill string count prior to
taking the seabed sample. During drilling, water depths were recorded at hourly interval for
variation in tidal heights. The water depths were then reduced to Lower Astronomical Tide (LAT)
and derived from a reference station based on predicted tides from Ke Ga Point tidal station. The
tidal variation chart is given on Plate 3
Table 3 - Water Depth
Location
BH SV-6X
Sampling & CPTU
Water depth
47.08m LAT
For more detailed assessment on water depth, we recommend that reference be made to the
relevant geophysical report.
2.4
Drilling was carried out over the moon pool on the MV PTSC Surveyor using the AG-30 marine
drilling rig with a top-drive Dando 1000 power swivel. This drilling system uses a straight flush
system, 2.5-inch API pipe (in 4.5m lengths) and an independent motion-compensation system.
Drilling mud was utilized where necessary to stabilize the walls of the borehole.
Data acquisition for CPT borehole was carried out using the downhole cone penetrometer with
pore pressure measurement (CPTU) unit. A.P Van Der Berg real time system measurements
included resistance at the cone tip, side friction and dynamic pore pressure. Tests were
completed generally within a 3m-stroke length. The results of CPTU, qc, qt and qnet are presented
graphically against depth together with friction ratio, Rf and Pore Pressure measurement and
Pore Pressure Ratio on Plates 6a to 6f.
Undisturbed samples were recovered at selected intervals using a push sampler. Both thin walled
(71.0mm inner diameter) and thick walled (70.0mm inner diameter) Shelby tubes were used
during the sampling program. Both types of sample tubes used were welded stainless steel
tubing. Push samples are marked on the boring log with P. Compilation of all test data is
presented in the Summary Boring on Plate 12.
All samples recovered were sent for testing at the MV PTSC Surveyor field laboratory. Untested
sample portions are kept in PVC containers, waxed and sent to the onshore laboratory for further
testing.
3.0
LABORATORY TESTING
Laboratory tests were performed on recovered samples to evaluate pertinent physical properties
of the subsoil encountered. Strength and deformation data obtained from the tests were further
reviewed and additional tests performed once samples were received at the selected onshore
geotechnical laboratory. The laboratory tests were conducted in general accordance with British
Standard and ASTM standards.
In the field laboratory, all cohesive samples were tested for shear strength using the motorized
miniature vane while the samples were still in the Shelby tubes or a representative sample after
extrusion. The samples were then extruded and visually classified by the geotechnical engineer
and laboratory technician. Photographs of selected extruded samples were taken and are
presented on Plates A126 to A128. After classification, shear strength measurements were
performed with the torvane (hand vane) and pocket penetrometer. Unconsolidated Undrained
(UU) triaxial test was performed on selected samples collected in the field.
Densities and water contents were obtained on samples from each Shelby Tube and the
remaining untested portions of the samples were sealed in wax for further testing at the
designated onshore laboratory. Additional testing such as Atterbergs Limits and particle size
distribution would be performed onshore to further assist in classification of the soil. Onshore UU
triaxial tests would be conducted on both undisturbed and remoulded samples to yield
information on the remoulded strength/sensitivity of the soils and to provide a QA/QC check on
tests performed offshore. These tests are highlighted in a different colour on the accompanying
plates. It is shown in the borehole logs (Plates 4a to 4g) that offshore and onshore UU trixial test
results agree reasonably well.
One dimensional (oedometer) consolidation tests were also carried out on selected cohesive
samples. The consolidation compressibility characteristics of the cohesive soils were determined
by performing the oedometer tests. The oedometer test results were presented as void ratio
versus pressure (e-log p) curves in Plates A106 and A107.
For determination of internal friction angle of sand, direct shear box tests were also conducted on
reconstituted sand samples with estimated in situ densities at onshore laboratory as shown in
plates A111 to A124.
Results from all laboratory tests are tabled in the Summary of Laboratory Test Results, Plates 7a
to 7f. The descriptions of the laboratory testing procedures are presented in Plates B1 to B4 in
this report.
4.0
SUBSOIL CONDITIONS
The subsoil condition encountered by the soil boring at the locations comprises generally clays
silt and sand layer. A summary of the major strata encountered during boring of BH SV-6X is
presented below:
Table 6 - Soil Stratigraphy
Location
: BH SV-6X
Coordinates : E 862 460.08 m; N 1 144 836.27 m
Layer
Depth Below Seabed (m) Thickness (m)
From
To
1
0.0
3.1
3.1
Description
Medium dense silty fine SAND
3.1
4.2
1.1
4.2
5.2
1.0
5.2
7.5
2.3
7.5
10.0
2.5
10.0
15.0
5.0
15.0
19.0
4.0
19.0
23.0
4.0
23.0
27.0
4.0
10
27.0
30.0
3.0
11
30.0
33.0
3.0
12
33.0
38.0
5.0
13
38.0
41.0
3.0
14
41.0
45.0
4.0
15
45.0
51.7
6.7
16
51.7
58.0
6.3
17
58.0
65.6
7.6
18
65.6
67.0
1.4
19
67.0
73.0
6.0
20
73.0
74.3
1.3
21
74.3
76.3
2.0
22
76.3
78.4
2.1
23
78.4
79.2
0.8
24
79.2
81.0
1.8
Dense SILT
25
81.0
86.0
5.0
26
86.0
88.6
2.6
Dense SILT
27
88.6
90.8
2.2
28
90.8
93.0
2.2
Dense SILT
29
93.0
97.0
4.0
30
97.0
102.5
5.5
31
102.5
103.4
0.9
32
103.4
106.0
2.6
33
106.0
107.3
1.3
34
107.3
109.0
1.7
Dense SAND
35
109.0
116.3
7.3
36
116.3
123.0
6.7
37
123.0
125.0
38
125.0
134.0
9.0
39
134.0
139.0
5.0
40
139.0
140.0
1.0
Results from CPTU indicate that the cone resistances (qc) recorded for the stiff clays are about
1MPa to 2MPa while the very stiff clays recorded approximately 2MPa to 3MPa. Meanwhile, the
hard clays recorded up to 5MPa of cone resistance reading. The friction ratio (Rf), i.e. the ratio of
local friction to cone resistance of the soils is generally around 2% for the clays.
Results of Atterbergs Limits are mostly plotted above the Plasticity Chart of the Unified Soil
Classification System A-line (ASTM D2487) as shown on Plates A1 to A13. The results show
that the clays are generally of low to high plasticity. Meanwhile the grain size distribution curves
indicate that the clays are generally lean clay.
5.0
DESIGN PROFILE
In the selection of the design profile, several criteria were considered; i.e. the shear strength
measured from offshore laboratory testing, trends in CPTU data, empirical correlations and
engineering judgement based on the soil characteristics in the region. Design profiles for the
borehole are presented on the Summary Boring, Plate 12.
5.1
Submerged Density
All the samples were tested in the field laboratory for densities and water content. The
submerged density of the soil is then computed from the measured wet density and unit weight of
the sea water, assuming that the soil is fully submerged.
(b - w)g
where
5.2
The ratio of undrained shear strength to effective overburden pressure (Su/v0) and Plasticity
Index (PI) was considered based on the empirical relationship as given by Skempton (1970) for
normally consolidated clays:
(Su/v0)nc = 0.11 + 0.0037 PI
where
PI = Plasticity Index
The ratio of undrained shear strength to effective overburden pressure (Su/v0)nc is estimated
to be approximately 0.17 for this location.
The undrained shear strength (Su) in cohesive soils may also be estimated from the cone
resistance by applying the semi-empirical formula:
Su
qt
qc + u (1 a)
qc
cone resistance
v0
Nkt
cone factor
where
Correlation between the measured cone resistance and the undrained shear strengths at the
borehole location indicate a cone factor Nkt of about 20 to 25 (30m to 132.8m) and 25 to 28
(134m to 139.8m) were appropriate for this location.
The torvane generally measures undrained shear strength values smaller than 250kPa and is
appropriate for testing most clay samples at this location. However, the results could be scattered
depending on the inclusion and quantities of sand/silt in that clay layer. The motor vane
measures undrained shear strength in a more controlled fashion than the torvane. The motor
vane is typically not reliable for very soft clay (Su < 5kPa) due to the inability of being able to
isolate the sample from rotating with the vane. The pocket penetrometer gives a shallow bearing
capacity type failure within a small zone and can only be used for clay/silt with undrained shear
strength of 10kPa and above.
In the UU triaxial tests, a larger soil mass is compressed to failure. Higher strength values may
be obtained from the UU triaxial test due to either sand/silt content or unsaturated sample or
both. An unsaturated sample may induce relatively high undrained shear strength due to the
effective stress increase from the confining pressure in the triaxial chamber. There were some
slight differences in the results of the UU tests performed offshore vs. onshore. However, these
results were felt to be due to natural occurrences of shell fragments or inclusions of silt, and or
sand within the sample and not from any procedural differences in the test method.
Design parameters were selected based on these considerations, as shown on Plate 13 with
greater emphasis being given to the UU triaxial, motor vane results and the deduced CPTU data.
10
5.3
Granular Soils
Design parameters of sand are the angle of internal friction and the submerged density. The
angle of internal friction was selected based on gradation. The procedure to estimate relative
density is available for siliceous sands, e.g. Jamiolkowski et al. (2001).
Dr
qc
1
ln
2.9 141 ' v 0 0.55
With the consideration of gradation and fine contents, limits for the estimated angles may be
applied based on the API RP 2A WSD (2000). Relative density profiles are shown on Plate 11.
Table 6 shows the shear box results and the design shear strength for granular soils.
Table 6 Shear Box Results
Depth
Soil
Soil/Pile Friction
Submerged
Description
Angle
Unit weight
(degree)
Design Shear
(kN/m)
0.0m to 3.1m
Medium dense
silty fine SAND
P1B (0.4m) = 28
P2A (1.2m) = 29
P3C (2.6m) = 28
9.5
25
4.2m to 5.2m
Medium dense
silty fine SAND
10.8
25
7.5m to 10.0m
Medium dense
sandy SILT
9.4
25
45.0m to 51.7m
Dense
sandy SILT
10.1
30
76.3m to 78.4m
Dense
sandy SILT
P43B (77.6m) = 31
10.8
30
81.0m to 86.0m
Dense
silty fine SAND
9.8
30
11
116.3m to 123.0m
Dense
fine SAND
P53B (117.5m) = 30
10.1
30
125.0m to 134.0m
Dense
silty fine SAND
P55B (125.7m) = 33
P56C (129.6m) = 33
10.1
30
5.4
State of Consolidation
The stress history of a soil is commonly expressed in terms of over-consolidation ratio (OCR) and
defined as:
p
=
v0
Current overburden stress can be derived from direct measurement of submerged unit weight
while the past maximum effective stress or pre-consolidation pressure (p) can be assessed from
the oedometer test results.
The OCRs may also be assessed from undrained shear strength data using the following
equation given by Ladd (1974):
OCR0.85
Su
Su
=
v0
site
v0
nc
On the other hand, results from the cone resistance can also give an indication of the OCR:
qt - v0
OCR
v0
5.5
Sensitivity
The sensitivity of the clay (St) is useful to assess the reduction of the peak undrained shear
strength of the soil in remoulded condition without a change in water content.
12
The common method to compute the soil sensitivity is through the ratio of the undrained shear
strength value to its remoulded shear strength value as recommended by Lambe and Whitman
(1969) below;
Su
St
=
Sur
The sensitivity of the soil could also be estimated from the CPTU data, through the friction ratio
(Rf) in percent as recommended by Schmertmann (1978) below;
Ns
St
=
Rf
where Ns is a constant and varies with local condition. For this location, Ns = 1.0 to 4.0 has been
adopted when evaluating St.
The general guideline to assess the soil sensitivity is given as follows:
Table 7 - Soil Sensitivity
Description
St value
Low sensitivity
St < 4
Medium sensitivity
4 < St < 8
High sensitivity
8 < St < 16
Quick sensitivity
St > 16
The sensitivity of the clays was plotted against depth in Plate 10 for this location to get an
overview of the sensitivity profile at the site. For the BH SV-6X location, it is observed that the
sensitivity range is generally 1 to 5 using the CPTU, onshore remoulded UU triaxial and
remoulded motor vane data. Tests from onshore remoulded UU triaxial and remoulded motor
vane show that sensitivity values are generally within the CPTU data and are closer to what
should be adopted for these soils.
13
6.0
The static method of pre-determining pile capacities was used to predict ultimate compressive
and tensile capacities of pipe piles installed to various penetrations below seabed. The piles will
derive axial capacity from two sources; namely the frictional soil resistance along the length of the
pile and end bearing at the tip of pile. Mathematical expression is defined by:
Q
Qs + Qp
f As + q Ap
Qs
Qp
As
Ap
where
Frictional resistance of embedded outer surface of the pile and end bearing on
the total cross-sectional area of the pile (plugged), mathematical expression
given as:
Q
fo Ao + qp Ap
fo
Ao
qp
Ap
where
ii)
Frictional resistance of inner and outer pile surfaces and end bearing on the
wall area of the pile tip (unplugged), mathematical expression is as shown:
Q
fo Ao + fi Ai + qw Aw
fi
Ai
embedded length
qw
Aw
wall area = t (d t)
wall thickness
where
14
6.1
Computation Methods
Several methods are available for computing the axial pile capacity. The API RP 2A (2000)
methods are discussed herein.
API METHOD
Unit skin friction
f (sand)
K vo tan
f (clay)
Su
q (sand)
Nq vo
q (clay)
Nc Su
Su
Nq
Nc
where
The empirical adhesion factor () as recommended by the API RP2A (2000) is computed as
follows:
0.5 -0.5
for
1.0
0.5 -0.25
for
> 1.0
Limiting Values
The API RP 2A (2000) recommended limit values for both unit skin friction and unit end bearing
values for cohesionless soil as shown below:
Density
Soil Description
Soil/Pile
Friction
Angle
(degrees)
Very Loose
Loose
Medium Dense
Sand
Sand-Silt
Silt
15
Skin Friction
kPa (ksf)
End Bearing
MPa (ksf)
47.8 (1.0)
1.9 (40)
15
Loose
Medium Dense
Dense
Sand
Sand-Silt
Silt
20
12
67.0 (1.4)
2.9 (60)
Medium Dense
Dense
Sand
Sand-Silt
25
20
81.3 (1.7)
4.8 (100)
Dense
Very Dense
Sand
Sand-Silt
30
40
95.7 (2.0)
9.6 (200)
Dense
Very Dense
Gravel
Sand
35
50
114.8 (2.4)
12.0 (250)
6.3
Based on these procedures and the selected design shear strength profile on Plate 5, ultimate
pile capacities were computed for the 762mm (30-in), 914mm (36-in) diameter conductors and
1219mm (48-in) diameter piles for this location. The ultimate tensile capacity of a pile at a given
penetration is taken as the minimum of the conditions i) and ii) in Section 6.0. The results of the
pile capacity computation are presented on Plates 15a to 15d.
The unit values of skin friction and end bearing were computed using the different approaches as
discussed in the foregoing. The following ultimate capacity curves were presented separately for
the three approaches:
i)
ii)
Pile penetration should be selected to provide factors of safety of at least 2.0 and 1.5 with respect
to normal operating loads and design storm loads, respectively. These factors of safety should be
applied to the design compressive and tensile loads.
16
7.0
Cyclic loading produces potential deterioration of the soil at large strains particularly near the
seafloor. The P-Y data developed for this study is applicable to single, isolated piles subjected to
repeated lateral load. The procedures of Matlock method (1970) for soft clay and Reese et al
(1974) for sand as recommended by API RP2A (2000) were used herein. In accordance with API
RP2A (2000) and industry practice, the factor J has been taken as 0.5 for clay strengths less than
96kPa and 0.25 for stronger clays. For cyclic loading and for stiffer clays (Su > 96kPa), the
maximum value of P is limited to 0.5Pu and to 0.5(X/XR). Pu for depth X less than the depth of
reduced resistance XR. Pu is defined as the ultimate lateral resistance for static conditions.
Design shear strength and submerged unit weights used in our computations are presented on
Plate 12. Values of 50 which are the strain at half the maximum compressive stress were
generally selected using stress-strain data from the unconsolidated undrained (UU) triaxial tests
and general values recommended by Matlock (1970). For sand layers, the initial moduli (Ki) are
estimated based on the friction angles and cone resistance as recommended by the API RP 2A
(2000). The value of the neutral penetration (Xr) is determined to be in the range of 10.0m to
15.0m for this location.
The recommended values of 50 (Matlock, 1970) are shown below:
Table 9 - Values of 50
50 (%)
Soil strength
Su (kPa)
Very soft
0 - 12
2.0
Soft
12 - 25
2.0
Firm
25 50
1.5
Stiff
50 100
1.0
Very stiff
100 200
0.5
Hard
200 - 400
0.5
The results of the analyses are presented on Plates 17a to 17i for the 762mm (30-in), 914mm
(36-in) diameter conductors and 1219mm (48-in) diameter piles for the location.
17
8.0
Axial load-deformation data giving mobilization of skin friction with respect to relative
displacement between pile and soil have been calculated using the three different
recommendations of the API RP2A (2000). T-Z data representing the development of soil-pile
friction along the pile shaft, and Q-Z data representing the development of end bearing resistance,
have been generated.
When the total inside unit skin friction is greater than the bearing capacity of the soil beneath the
plug, the pile is said to be plugged. When the converse situation occurs, the soil plug is
considered to move up relative to the pile and the pile is said to be unplugged.
For the SV-6X location, the T-peak value in clay was taken as the computed unit skin friction while
the T-residual value was taken as 90% of the peak based on UU results and local experience.
The quake value (Zmax) at T-peak value is assumed to be 1% of pile diameter for clay. The shape
of the load-deformation curves is a hyperbolic-type as recommended by the API RP2A. The T-Z
data are presented for the 762mm (30-in), 914mm (36-in) diameter conductors and 1219mm (48in) diameter piles on Plates 18a to 18l.
The computed axial load-deformation data giving mobilization of unit end bearing with respect to
relative displacement between pile tip and soil (Q-Z curves) are presented on Plates 19a to 19p
for the 762mm (30-in), 914mm (36-in) diameter conductors and 1219mm (48-in) diameter piles.
The maximum resistance at any depth has been based on the available unit resistance derived at
the tip at the given depth. The quake value (Zmax) at Q-peak value is assumed to be 10% of pile
diameter.
18
9.0
The weight of the platform jacket will be supported by mats bearing on the seabed soils until piles
are installed. The procedures for computing the mud mat bearing capacity are discussed in this
section, which may be adopted for sizing the mat area or checking the bearing stability of the
mud mat.
9.2
Mud mat bearing capacity analyses at the BH SV-6X location were carried out based on the
following interpreted soil parameters:
Table 10 - Shear Strengths for Mud Mat Stability Analyses
Depth
Layer
Soil Description
SAND
Stiff to very hard lean
CLAY
Shear strength /
Submerged
Angle of
unit weight
internal friction
(kN/m3)
From
To
0.0m
3.1m
25o
3.1m
7.5m
9.0
(mudline)
10.8
The ultimate net bearing capacity, qu, of cohesionless soils is given by the Buisman-Terzaghi
equation:
qu c uN c '1 D (N q 1) 1 2 s ' 2 B N
where
cu
1
2
B
D
Nc,Nq,N
s
=
=
=
=
=
=
=
In consideration of the cohesive layer encountered at depth 3.1m below sand layer, the ultimate
net bearing capacity of layering system is also calculated using the Load-spread Method (Young
et al, 1984) and Skempton (1951) equations, as follow:
qu ( 1
where
2H 2
) qb
n B
H
n
D
B
)( 1 0.2 )
B
L
and
q b 5cu ( 1 0.2
=
=
19
Based on the above methods, mud mats for temporary structure support resting at seafloor at the
BH SV-6X location may be designed using the following equations:
qu = 50B (1-0.4B/L)
for B 1.55m
The total ultimate bearing capacity of the mud mat is the ultimate bearing capacity as given
above times the base area of the mud mat and applicable tubular member area rest on the
seafloor or embedded seafloor. A factor of safety of 2 is recommended to be applied to determine
the mat area.
9.2
Sliding Stability
The sliding stability for the mud mat, with respect to inclined loading can be checked based on
the recommendations by API RP 2A (2000) in Section 6.0 as given below;
=
cA + Q tan
0 (usually sand)
H
where
The recommendation above applies where the horizontal failure plane in the soil is insured by
structural constraints, i.e. shear skirts at sufficiently close spacing. Reduced soil strength should
be applied where structural constraints are not provided. A factor of safety of 1.5 is recommended
to be applied to check the mat area against sliding failure.
20
10.0
PILE INSTALLATION
Installation of piles to target penetration requires detailed planning and procedures. Driveability
study provides the means to select an optimal hammer-pile-soil system. Wave equation analysis
can be conducted using the estimated soil resistance during driving (SRD) obtained from soil
investigation data. The SRD is computed in the same manner as static pile capacity, but the soil
inside the pile (plugged condition) remains stationary during driving because of the following
reasons:
a)
Shock waves from hammer blows travel faster in steel than in the soil plug due to
difference in density as well as Youngs modulus of steel and the saturated soil. Hence,
the soil plug cannot move in phase with the pile.
b)
The soil plug has inertia and requires a force bigger than the inner soil-pile friction to
accelerate it during driving. The force required is generally more than the available friction
between the soil and the steel inside the plug.
10.1
Estimation of SRD
In pre-installation driveability studies (Kiu and Tan, 1993; Yu et al, 2001), the SRD was generally
computed using:
=
Sur
Ao
Ai
qc
Cone resistance
Ap
SRD
where
The remoulded shear strengths of the soils are given on Plate 20. These values are based on
measured cone sleeve frictions from CPTU and the results from remoulded UU and motor vane
tests. The selected remoulded undrained shear strength is about 30% of the API RP2A (2000)
unit skin friction for clays. For sand layers, qc/300 is applied. The tip resistance was computed
using the net wall area of pile tip and the measured cone resistance, qc.
21
In computing the SRD, the inner friction in the pile is considered for continuous driving condition
(unplugged case). Plugged condition is considered for setup driving case. A reduced inner skin
friction (k) as obtained from previous back-analysed data was adopted in this report.
An average factor k was taken as 0.15 for clay, 0.5 for medium dense sand and 0.7 for dense
sand. The parameters used in the computation of the SRD are given on Plates 21a and 21b with
the estimated SRDs against depths shown on Plates 22a to 22d for the pile diameter.
10.2
Interruption in driving would cause an increase in SRDs. From the results of previous
measurements and studies, set-up factor of 1.2 was measured after 24 hours delays. Higher setup factor has been reported and this is due mainly to long delays. Hence, it is recommended to
keep delays in driving as short as possible. In this report, the lower and upper bound in clays are
taken as 1.2 and 2.0 for clays corresponding to the partial and full setup cases respectively and
1.0 for sand.
10.3
The relationship between available hammer energy and the SRDs has been established using a
pile driving simulation computer program, GRLWEAP version 2010 based on the onedimensional wave equation theory. The input parameters are:
a) Pile driver (hammer) characteristics
b) Pile characteristics
c) Soil resistance around and below the pile
Two (2) conductor and one (1) pile diameters were selected for the driveability analysis, namely
762mm (30-inch), 914mm (36-inch) and 1219mm (48-inch). Hammer and soil input data is shown
on Plate 23.
Driveability analyses were performed for piles using two (2) hammers at 90% efficiency. Results
of the wave equation analyses for the piles are presented as SRDs vs. Blowcounts on Plates 24a
to 24h for the pile-hammer sets respectively.
10.4
Each pile or conductor section on which a pile hammer (pile top drilling rig, etc.) will be placed
should be checked for stresses due to placing the equipment. These loads may be the limiting
factors in establishing maximum length of add-on sections. This is particularly true in cases
where piling will be driven or drilled on a batter. The most frequent effects include static bending,
axial loads, and arresting lateral loads generated during initial hammer placement.
22
Experience indicates that reasonable protection from failure of the pile wall due to the above
loads is provided if the static stresses are calculated as follows:
i)
ii)
Bending moments and axial loads should be calculated using the full weight of the pile
hammer, cap, and leads acting through the centre
masses, and the weight of the pile add-on section with due consideration to pile batter
eccentricities. The bending moment so determined should not be less than that
corresponding to a load equal to 2 percent of the combined weight of the hammer,
cap, and leads applied at the pile head and perpendicular to its centreline.
iii)
Allowable stresses in the pile should be calculated in accordance with Sections 3.2
and 3.3 of the API RP 2A (2000). The one third increases in stress should not be
allowed.
10.5
Stresses during driving are checked as per recommendation from Section 6.10.5 in the API RP
2A (2000) based on the conservative criterion that the sum of the stresses due to the impact of
the hammer (the dynamic stresses) and the stresses due to axial load and bending (static
stresses) should not exceed the minimum yield strength of the steel. The static stress during
driving may be taken to be the stress resulting from the weight of the pile above the point of
evaluation plus the pile hammer components actually supported by the pile during the hammer
blows, including any bending stresses resulting thereof.
The computed Maximum Compressive Stresses as derived from the computer printouts at 300
blows/ft of driving are in the order of 141MPa to 263Mpa, which are within the allowable limits of
310MPa (0.9Fy of steel).
23
10.6
Self Penetration
Initial penetrations of piles can be determined assuming penetrations under the pile self weight,
the weight of hammer and the buoyancy force. The calculation of pile self penetration is detailed
as shown below;
Total weight in water
Where
Pile weight in air
Buoyancy force
The weight of the pile and hammer set is then compared to the corresponding soil resistance at
the top layers to determine the estimated self penetration of the pile-hammer set. Selfpenetrations of the piles & hammer at this platform location would be about 5.2 m to 19.1 m
below the seabed.
24
10.7
By combining the computed SRDs on Plates 22a to 22d and SRDs vs. Blowcounts results on
Plates 24a to 24h, predicted blowcounts using the respective pile-hammer sets are presented on
Plates 25a to 25g. Predicted final penetrations at a commonly used refusal criterion of 300
blows/300mm are presented in the table below for continuous driving and set-up conditions for
the various design approaches at the proposed location.
Table 10 Results of Driveability Analysis
Pile Penetration Below Mudline (m)
Hammer Type
Efficiency
(%)
Location
Conductor
Size
(Diameter x
Wall
Thickness,
mm)
Set-Up
Condition
IHC S280
111
102 - 79
IHC S280
125
116-100
>140
138-129
IHC S280
136
125-107
IHC S750
>140
>140-125
IHC S280
>140
136-115
IHC S750
>140
>140-137
(762 x 25.4)
(914 x 38.1)
IHC S750
SV-6X
90
(1219 x 50)
(1219 x 60)
Results of the penetration predicted at 300 blows per 0.3m indicate that the 762mm (30-in) and
914mm (36-in) diameter conductors and 1219mm (48-in) diameter piles can be driven to 111m to
beyond 140m under continuous driving conditions whilst for setup conditions the conductors and
piles can be driven to 79m to beyond 140m respectively using IHC S280 and IHC S750 hammers
at 90% efficiency.
It must be noted that these recommendation are based on the given conductor and pile
diameters. Refined driveability study should be carried out for the final detailed pile make-up
together with the proposed hammer spread.
25
11.0
LIST OF REFERENCES
1.
American Petroleum Institute. 2000. API Recommended Practice for Planning, Designing
and Construction of Fixed Offshore Platforms Working Stress Design, 21st Edition, (Also
LRFD 1st Edition, 1993) American Petroleum Institute, Washington DC.
2.
American Society for Testing and Materials. 2007. Annual Book of ASTM Standards,
Volume 04.08: Soil and Rock (I).
3.
4.
density and shear strength of sands from CPT and DMT, Soft Ground Construction 2001,
ASCE, GSP No. 119, pp. 201-238.
5.
Matlock, H. 1970. Correlation for Design of Laterally Loaded Piles in Soft Clay, Preprints,
OTC Paper 1204, Vol. 1, pp 557 588.
7.
Reese, L. C., et al 1974. Analysis of Lateral Loaded Piles in Sand, Preprints, OTC Paper
2080, Vol. 2, pp 473 480.
8.
9.
10.
26
12.0
LIST OF PLATES
Appendix
Borehole Log
Summary CPTU
4a to 4g
5
CPTU Profile
6a to 6f
7a to 7g
10
11
Summary Boring
12
13a to 13c
14
15a to 15d
16a and 16b
P-Y Data
17a to 17i
T-Z Data
18a to 18l
Q-Z Data
19a to 19p
20
21a and 21b
22a to 22d
23
24a to 24h
Predicted Blowcounts
25a to 25g
Appendix A
Plasticity Chart
A1 to A13
A14 to A50
A51 to A105
A106 to A107
A108 to A110
A111 to A124
Chemical Tests
Photographs of Selected Soil Samples
A125
A110 to A116
27
Appendix B
B1 to B4
B5
B6
Appendix C
C1 and C2
C3
28
APPENDIX
FR
1145000
1144900
Coordinates BH SV-6X:
Northing (m)
1144800
E 862 460.08m
N 1 144 836.27m
1144700
1144600
1144500
862200
862300
862400
862500
862600
862700
Easting (m)
Legend:
Made by
Checked by :
SP
CHG
Plate 2
19:03
22:33
2:18
6:03
9:48
13:33
19/04/2013
17:45
21:30
1:15
5:00
8:45
12:30
52.0
50.0
Water Depth (m)
BH SV-6X
BLOCK 15-01
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
PGS/SI/2013/CLJOC/06/SV-6X/FR
18/04/2013
17/04/2013
48.0
47.1m LAT
46.0
Made by
Checked by
44.0
Note:
The water depth was measured by calibrated echosounder onboard PTSC Surveyor and reduced to Lowest Astronomical
Tides (LAT) based on the predicted tides at Ke Ga Point tidal station.
SP
18/06/2013
CHG
Plate 3
DOWNHOLE
CPT
SAMPLE NO
ft
SOIL
PROFILE
DEPTH
SOIL DESCRIPTION
Torvane
Pocket Penetrometer
Motor Vane
Motor Vane Remoulded
CIU Triaxal
Est. from CPT:Nkt=20
Normally Consolidated Profile
UU Triaxial Onshore
UU Triaxial Offshore
UU Remoulded
In situ Vane
In situ Vane Remoulded
Est. from CPT:Nkt=25
PL
PI
MC
(%)
(kN/m )
200
300
400
LL
SUBMERGED
DENSITY
10 11
25
50
75
P1
1
4
P2
2
8
P3
P4
12
4
P5
16
P6
16
14
11
20
P7
7
24
14
22
P8
P9
8
28
P10
P11
32
10
P12
11
36
20
P13
23
12
40
P14
17
13
44
P15
16
18
14
P16
48
15
P17
16
52
P18
17
13
17
56
P19
10
18
60
P20
11
19
64
P21
AG/III/PRO/F007 REV. 1
18
Date Performed
17-04-2013 - 19-04-2013
Water Depth
47.1m LAT
Coordinates
E 862,460m; N 1,144,836m
Made By/Date
SP - 03-06-2013
Plate 4a
DOWNHOLE
CPT
SAMPLE NO
ft
SOIL
PROFILE
DEPTH
SOIL DESCRIPTION
Torvane
Pocket Penetrometer
Motor Vane
Motor Vane Remoulded
CIU Triaxal
Est. from CPT:Nkt=20
Normally Consolidated Profile
UU Triaxial Onshore
UU Triaxial Offshore
UU Remoulded
In situ Vane
In situ Vane Remoulded
Est. from CPT:Nkt=25
PL
PI
MC
(%)
(kN/m )
200
300
400
LL
SUBMERGED
DENSITY
10 11
25
50
75
P22
68
21
10
P23
22
72
P24
23
76
P25
24
80
26
P26
25
P27
15
84
26
P28
27
88
P29
28
16
92
34
P30
29
96
P31
30
100
31
CPT1
104
32
33
108
P32
34
112
35
116
CPT2
36
120
37
P33
124
38
39
128
AG/III/PRO/F007 REV. 1
Date Performed
17-04-2013 - 19-04-2013
Water Depth
47.1m LAT
Coordinates
E 862,460m; N 1,144,836m
Made By/Date
SP - 03-06-2013
Plate 4b
132
DOWNHOLE
CPT
SAMPLE NO
ft
SOIL
PROFILE
DEPTH
CPT4
41
136
SOIL DESCRIPTION
Torvane
Pocket Penetrometer
Motor Vane
Motor Vane Remoulded
CIU Triaxal
Est. from CPT:Nkt=20
Normally Consolidated Profile
UU Triaxial Onshore
UU Triaxial Offshore
UU Remoulded
In situ Vane
In situ Vane Remoulded
Est. from CPT:Nkt=25
PL
200
300
400
10 11
42
25
50
75
P34
LL
MC
(%)
(kN/m )
PI
SUBMERGED
DENSITY
15
140
43
CPT5
44
45
144
148
P35
46
152
47
CPT6
156
48
160
49
P36
50
164
51
168
CPT7
52
172
17
53
P37
176
54
55
180
CPT8
56
184
57
188
17
P38
58
192
CPT9
59
196
AG/III/PRO/F007 REV. 1
Date Performed
17-04-2013 - 19-04-2013
Water Depth
47.1m LAT
Coordinates
E 862,460m; N 1,144,836m
Made By/Date
SP - 03-06-2013
Plate 4c
DOWNHOLE
CPT
SAMPLE NO
ft
SOIL
PROFILE
DEPTH
CPT9
61
SOIL DESCRIPTION
Torvane
Pocket Penetrometer
Motor Vane
Motor Vane Remoulded
CIU Triaxal
Est. from CPT:Nkt=20
Normally Consolidated Profile
UU Triaxial Onshore
UU Triaxial Offshore
UU Remoulded
In situ Vane
In situ Vane Remoulded
Est. from CPT:Nkt=25
PL
200
300
400
LL
MC
(%)
(kN/m )
9
10 11
25
50
75
200
P39
62
PI
SUBMERGED
DENSITY
23
204
63
208
CPT10
64
212
65
P40
66
216
CPT11
67
220
68
224
69
P41
228
70
232
71
CPT13
72
73
236
240
P42
74
244
75
CPT14
248
76
252
77
P43
78
256
79
260
AG/III/PRO/F007 REV. 1
Date Performed
17-04-2013 - 19-04-2013
Water Depth
47.1m LAT
Coordinates
E 862,460m; N 1,144,836m
Made By/Date
SP - 03-06-2013
Plate 4d
DOWNHOLE
CPT
SAMPLE NO
ft
SOIL
PROFILE
DEPTH
CPT15
264
81
268
82
PL
100
200
300
LL
MC
(%)
(kN/m )
400
PI
SUBMERGED
DENSITY
10 11
25
50
75
15
272
CPT16
84
UU Triaxial Onshore
UU Triaxial Offshore
UU Remoulded
In situ Vane
In situ Vane Remoulded
Est. from CPT:Nkt=25
P44
83
SOIL DESCRIPTION
Torvane
Pocket Penetrometer
Motor Vane
Motor Vane Remoulded
CIU Triaxal
Est. from CPT:Nkt=20
Normally Consolidated Profile
276
85
280
P45
86
CPT17
284
87
CPT18
288
88
CPT19
89
292
P46
10
90
296
91
CPT20
300
92
304
93
P47
94
95
13
308
312
CPT21
96
316
97
320
P48
17
98
324
99
CPT22
AG/III/PRO/F007 REV. 1
Date Performed
17-04-2013 - 19-04-2013
Water Depth
47.1m LAT
Coordinates
E 862,460m; N 1,144,836m
Made By/Date
SP - 03-06-2013
Plate 4e
DOWNHOLE
CPT
SAMPLE NO
ft
SOIL
PROFILE
DEPTH
CPT22
101
SOIL DESCRIPTION
Torvane
Pocket Penetrometer
Motor Vane
Motor Vane Remoulded
CIU Triaxal
Est. from CPT:Nkt=20
Normally Consolidated Profile
UU Triaxial Onshore
UU Triaxial Offshore
UU Remoulded
In situ Vane
In situ Vane Remoulded
Est. from CPT:Nkt=25
PL
200
300
400
LL
MC
(%)
(kN/m )
PI
SUBMERGED
DENSITY
10 11
25
50
75
332
16
P49
102
336
105
344
12
P50
106
348
107
352
CPT24
108
356
109
P51
360
20
110
111
364
CPT25
112
368
113
372
P52
114
376
115
CPT26
116
117
380
384
P53
118
388
CPT27
119
392
AG/III/PRO/F007 REV. 1
Date Performed
17-04-2013 - 19-04-2013
Water Depth
47.1m LAT
Coordinates
E 862,460m; N 1,144,836m
Made By/Date
SP - 03-06-2013
Plate 4f
DOWNHOLE
CPT
SAMPLE NO
ft
SOIL
PROFILE
DEPTH
CPT27
396
121
SOIL DESCRIPTION
Torvane
Pocket Penetrometer
Motor Vane
Motor Vane Remoulded
CIU Triaxal
Est. from CPT:Nkt=20
Normally Consolidated Profile
UU Triaxial Onshore
UU Triaxial Offshore
UU Remoulded
In situ Vane
In situ Vane Remoulded
Est. from CPT:Nkt=25
PL
200
300
400
LL
MC
(%)
(kN/m )
PI
SUBMERGED
DENSITY
10 11
25
50
75
P54
123
400
CPT28
404
124
408
125
412
P55
126
416
127
CPT30
128
420
129
424
P56
130
428
131
CPT31
432
132
133
436
P57
134
440
CPT32
135
444
136
448
12
P58
137
452
138
CPT33
139
456
AG/III/PRO/F007 REV. 1
Date Performed
17-04-2013 - 19-04-2013
Water Depth
47.1m LAT
Coordinates
E 862,460m; N 1,144,836m
Made By/Date
SP - 03-06-2013
Plate 4g
ft
DOWNHOLE
CPT
SOIL
PROFILE
DEPTH
BELOW
MUDLINE
CONE RESISTANCE
qc, qt, qnet (MPa)
0
12
18
24
30
SLEEVE FRICTION
fs(kPa)
36
42
48 0
150
300
450
PORE PRESSURE
u2(MPa)
600 -4
-2
FRICTION RATIO
Rf (%)
4 0
PORE PRESSURE
RATIO Bq
8 -0.5
0.0
0.5
1.0
1.5
4
20
8
12
40
16
60
20
24
80
52
CPT9
200
CPT10
60
180
64
CPT13
72
220
240
CPT14
68
76
84
260
CPT16
80
280
88
300
CPT21
92
CPT12
CPT11
56
CPT8
CPT7
160
CPT15
48
140
CPT19
CPT18
CPT17
44
CPT6
40
CPT5
CPT4 CPT3
120
CPT20
36
CPT2
100
32
CPT1
28
96
100
340
CPT24
104
CPT23
CPT22
320
108
112
400
124
420
CPT31
128
132
440
CPT33
136
CPT30
120
CPT29CPT28
CPT27
380
CPT32
116
CPT26
CPT25
360
qc
qt
qnet
Rf :
fs
qt
Bq :
Ud
qt-vo
Date Performed
17-04-2013 - 19-04-2013
Water Depth
47.1 m LAT
Coordinates
E 862,460m; N 1,144,836m
Made By/Date
SP - 03-06-2013
Plate
ft
DOWNHOLE
CPT
SOIL
PROFILE
DEPTH
BELOW
MUDLINE
SLEEVE FRICTION
fs(kPa)
CONE RESISTANCE
qc, qt, qnet (MPa)
0
12
18
24
30
36
42
48 0
150
300
450
FRICTION RATIO
Rf (%)
PORE PRESSURE
u2(MPa)
600 -4
-2
4 0
PORE PRESSURE
RATIO Bq
8 -0.5
0.0
0.5
1.0
1.5
68
21
22
23
72
76
24
80
25
84
26
27
28
88
92
29
96
30
100
CPT1
31
104
32
33
34
108
112
116
CPT2
35
36
120
37
124
39
128
CPT3
38
qc
qt
qnet
Rf :
fs
qt
Bq :
Ud
qt-vo
Date Performed
17-04-2013 - 19-04-2013
Water Depth
47.1 m LAT
Coordinates
E 862,460m; N 1,144,836m
Made By/Date
SP - 03-06-2013
Plate 6a
ft
DOWNHOLE
CPT
SOIL
PROFILE
DEPTH
BELOW
MUDLINE
12
18
24
30
36
42
48 0
150
300
450
FRICTION RATIO
Rf (%)
PORE PRESSURE
u2(MPa)
600 -4
-2
4 0
PORE PRESSURE
RATIO Bq
8 -0.5
0.0
0.5
1.0
1.5
CPT4
132
SLEEVE FRICTION
fs(kPa)
CONE RESISTANCE
qc, qt, qnet (MPa)
41
136
42
140
CPT5
43
44
45
144
148
46
152
156
CPT6
47
48
160
49
50
164
168
CPT7
51
52
172
53
176
54
180
CPT8
55
56
184
57
188
58
CPT9
192
59
196
qc
qt
qnet
Rf :
fs
qt
Bq :
Ud
qt-vo
Date Performed
17-04-2013 - 19-04-2013
Water Depth
47.1 m LAT
Coordinates
E 862,460m; N 1,144,836m
Made By/Date
SP - 03-06-2013
Plate 6b
ft
DOWNHOLE
CPT
SOIL
PROFILE
DEPTH
BELOW
MUDLINE
SLEEVE FRICTION
fs(kPa)
CONE RESISTANCE
qc, qt, qnet (MPa)
6
12
18
24
30
36
42
48 0
150
300
450
600 -4
-2
4 0
PORE PRESSURE
RATIO Bq
8 -0.5
0.0
0.5
1.0
1.5
CPT9
FRICTION RATIO
Rf (%)
PORE PRESSURE
u2(MPa)
61
62
200
204
208
CPT10
63
64
212
65
216
CPT11
66
220
CPT12
67
68
224
69
228
70
232
CPT13
71
72
73
236
240
74
244
248
CPT14
75
76
78
252
256
79
260
CPT15
77
qc
qt
qnet
Rf :
fs
qt
Bq :
Ud
qt-vo
Date Performed
17-04-2013 - 19-04-2013
Water Depth
47.1 m LAT
Coordinates
E 862,460m; N 1,144,836m
Made By/Date
SP - 03-06-2013
Plate 6c
ft
DOWNHOLE
CPT
SOIL
PROFILE
DEPTH
BELOW
MUDLINE
12
18
24
30
36
42
48 0
150
300
450
FRICTION RATIO
Rf (%)
PORE PRESSURE
u2(MPa)
600 -4
-2
4 0
PORE PRESSURE
RATIO Bq
8 -0.5
0.0
0.5
1.0
1.5
CPT15
264
SLEEVE FRICTION
fs(kPa)
CONE RESISTANCE
qc, qt, qnet (MPa)
81
268
82
272
CPT16
83
84
276
85
280
284
CPT18
87
CPT17
86
288
CPT19
88
89
292
90
296
CPT20
91
300
92
304
93
95
308
312
CPT21
94
96
316
97
320
324
99
CPT22
98
qc
qt
qnet
Rf :
fs
qt
Bq :
Ud
qt-vo
Date Performed
17-04-2013 - 19-04-2013
Water Depth
47.1 m LAT
Coordinates
E 862,460m; N 1,144,836m
Made By/Date
SP - 03-06-2013
Plate 6d
ft
DOWNHOLE
CPT
SOIL
PROFILE
DEPTH
BELOW
MUDLINE
SLEEVE FRICTION
fs(kPa)
CONE RESISTANCE
qc, qt, qnet (MPa)
6
12
18
24
30
36
42
48 0
150
300
450
600 -4
-2
4 0
PORE PRESSURE
RATIO Bq
8 -0.5
0.0
0.5
1.0
1.5
CPT22
FRICTION RATIO
Rf (%)
PORE PRESSURE
u2(MPa)
101
332
102
336
340
CPT23
103
104
105
106
344
348
352
CPT24
107
108
356
109
360
110
364
CPT25
111
112
368
113
372
114
376
CPT26
115
116
117
380
384
118
CPT27
388
119
392
qc
qt
qnet
Rf :
fs
qt
Bq :
Ud
qt-vo
Date Performed
17-04-2013 - 19-04-2013
Water Depth
47.1 m LAT
Coordinates
E 862,460m; N 1,144,836m
Made By/Date
SP - 03-06-2013
Plate 6e
ft
DOWNHOLE
CPT
SOIL
PROFILE
DEPTH
BELOW
MUDLINE
SLEEVE FRICTION
fs(kPa)
CONE RESISTANCE
qc, qt, qnet (MPa)
0
12
18
24
30
36
42
48 0
150
300
450
FRICTION RATIO
Rf (%)
PORE PRESSURE
u2(MPa)
600 -4
-2
4 0
PORE PRESSURE
RATIO Bq
8 -0.5
0.0
0.5
1.0
1.5
396
123
400
404
CPT29
122
CPT28
121
124
408
125
412
126
416
CPT30
127
128
420
129
424
130
428
432
CPT31
131
132
134
436
440
CPT32
133
135
444
136
448
137
452
CPT33
138
139
456
qc
qt
qnet
Rf :
fs
qt
Bq :
Ud
qt-vo
Date Performed
17-04-2013 - 19-04-2013
Water Depth
47.1 m LAT
Coordinates
E 862,460m; N 1,144,836m
Made By/Date
SP - 03-06-2013
Plate 6f
P1
26
19
34
19.1
14.2
34
19.2
14.3
27
19.7
15.5
25
20.1
16.0
23
19.4
15.7
23
20.5
16.6
3.4
16
21.2
18.2
3.5
18
20.9
17.7
14
21.6
18.9
1.4
2.6
46
32
16
16
28
14
14
49
4.4
4.6
5.6
32
26
15
11
5.8
2.68
*SB
28
68
11
123
100
120
100
*UU/UUR
95
190
175
UU
90
75
UU
85
3.7
2540
180
578
1.4
12857
90
590
1.7
5294
18
21.5
18.2
18
20.6
17.4
2.71
21
20.6
17.0
18
21.2
17.9
100
200
17
20.7
17.7
123
225
UU
208
612
0.9
23111
19
21.0
17.6
140
225
*UU
160
620
1.8
8840
250
UU
147
639
1.9
7737
200
UU
225
647
1.6
14063
*SB
28
2.68
0.1
160
250
6.6
6.8
250
31
17
14
47
25
22
62
21
19.6
16.2
23
19.1
15.5
2.73
7.0
7.2
7.3
300
7.5
7.7
7.9
59
71
9.6
Date :
03-06-2013
Plate 7a
Made By :
SP
15.4
19.4
15.4
28
19.3
15.0
25
19.5
15.6
24
19.6
15.8
25
19.4
15.5
25
20.0
16.0
2.72
*SB
29
2.72
*SB
28
2.73
*SB
26
9.0
9.4
Date :
05-06-2013
19.4
26
8.0
8.6
Checked By :
CHG
26
9.8
79
10.0
10.1
113
200
10.3
125
275
10.5
23
19.7
16.0
150
250
10.7
24
20.3
16.3
163
275
*UU
146
10.9
23
19.8
16.1
170
225
UU/UUR
220
179
713
1.0
15208
717
1.4
15714
kPa
11.9
575
PRECONSOLIDATION
PRESSURE
(
)
c
CARBONATE
CONTENT
CHLORIDE
CONTENT
SULPHATE
CONTENT
ORGANIC
CONTENT
E50
CONFINING
EFFECTIVE
COHESION
(C')
REMOULDED
SHEAR STRENGTH
UNDRAINED
SHEAR STRENGTH
(Su)
29
20
8.4
AG/III/PRO/F010 REV. 1
TYPE OF
TEST
*SB
6.5
P12
IN SITU VANE
REMOULDED
2.68
6.0
6.4
P11
IN SITU VANE
28
5.4
P10
POCKET
PENETROMETER
*SB
5.0
5.2
P9
kPa
4.0
4.2
P8
3.0
3.6
P7
deg
2.68
3.2
P6
kPa
2.0
2.2
P5
TORVANE
MOTOR VANE
REMOULDED
MOTOR VANE
SPECIFIC GRAVITY
BULK
DRY
kPa
OEDOMETER
TEST
CHEMICAL TEST
1.0
1.2
P4
kN/m
STRAIN/MOD.
OF ELASTICITY
0.0
0.6
P3
0.4
P2
WATER CONTENT
PERCENT PASSING
No.200
PLASTICITY
INDEX
DENSITY
PLASTIC
LIMIT
DEPTH
SAMPLE No.
LIQUID
LIMIT
*
: Onshore Testing
UU
: Unconsolidated Undrained Triaxial
UUR : UU Triaxial Remoulded
CIU : Consolidated Undrained Triaxial
CD
: Consolidated Drained Triaxial
UCT : Unconfined Compression Test
SB
: Shear Box Test
: Angle of Internal Friction
: Strain at 50% Maximum Stress
: Modulus of Elasticity at 50% Max. Stress
50
PGS/SI/2013/CLJOC/06/SV-6X/FR
ATTERBERG LIMITS
23
20
kN/m
CARBONATE
CONTENT
CHLORIDE
CONTENT
SULPHATE
CONTENT
ORGANIC
CONTENT
CONFINING
EFFECTIVE
COHESION
(C')
REMOULDED
SHEAR STRENGTH
UNDRAINED
SHEAR STRENGTH
(Su)
TYPE OF
TEST
IN SITU VANE
REMOULDED
IN SITU VANE
PRECONSOLIDATION
PRESSURE
(
)
c
kPa
175
325
12.4
24
20.1
16.2
203
325
*OEDO
12.6
23
20.5
16.6
203
275
*UU/UUR
216
23
19.9
16.1
180
250
UU
144
753
1.5
9600
UU
178
768
1.4
12714
780
2.6
5171
784
3.2
3281
803
0.6
11333
806
2.4
1852
325
23
300
UU
228
12.0
38
21
17
80
2.73
101
15
760
181
13.0
13.2
63
150
13.4
113
275
37
21
16
24
20.0
16.1
23
20.3
16.5
119
200
23
20.0
16.2
188
180
*UU/UUR
136
23
19.7
16.0
138
150
UU
105
188
250
14.0
40
22
18
127
15.0
15.2
75
88
26
20.5
16.2
68
63
UU
68
15.6
25
19.4
15.5
50
75
*UU/UUR
45
15.8
23
19.7
16.0
15.4
20.0
34
21
13
84
15
44
65
16.0
16.2
81
60
16.4
81
55
16.6
16.8
35
18
17
18
20.9
17.7
88
63
*UU
128
825
1.5
8828
21
20.8
17.2
100
88
UU
93
829
0.6
15500
16
19.9
17.1
105
53
UU
97
837
1.6
6063
83
60
63
63
*UU
71
844
2.9
2474
UU
55
863
1.4
3929
UU
121
879
1.3
9308
UU
158
898
1.6
9875
17.0
17.2
17.4
17.6
25
15
10
25
14
11
35
17
18
32
18
21.3
18.0
2.69
18
20.9
17.7
50
70
17
20.4
17.4
50
63
88
180
19
21.3
17.9
100
125
20
21.0
17.5
100
150
113
150
20.4
18
21.4
18.1
138
20.6
19
21.2
17.8
125
100
88
150
18
21.0
17.8
88
150
18.0
18.4
18.6
19.0
19.2
19.4
19.6
Made By :
SP
Date :
05-06-2013
Date :
03-06-2013
Plate 7b
Checked By :
CHG
20.0
20.2
P23
16489
300
14.6
P22
1.3
16.0
23
14.4
P21
749
19.9
14.2
P20
15200
24
46
13.8
P19
1.5
15.7
13.6
P18
732
19.4
12.8
P17
kPa
23
11.7
P16
24
11.5
P15
deg
kPa
OEDOMETER
TEST
CHEMICAL TEST
11.0
11.3
P14
POCKET
PENETROMETER
kPa
12.2
AG/III/PRO/F010 REV. 1
TORVANE
MOTOR VANE
REMOULDED
MOTOR VANE
SPECIFIC GRAVITY
DRY
BULK
STRAIN/MOD.
OF ELASTICITY
E50
43
WATER CONTENT
PERCENT PASSING
No.200
PLASTICITY
INDEX
10.9
P13
DENSITY
PLASTIC
LIMIT
DEPTH
SAMPLE No.
LIQUID
LIMIT
*
: Onshore Testing
UU
: Unconsolidated Undrained Triaxial
UUR : UU Triaxial Remoulded
CIU : Consolidated Undrained Triaxial
CD
: Consolidated Drained Triaxial
UCT : Unconfined Compression Test
SB
: Shear Box Test
: Angle of Internal Friction
: Strain at 50% Maximum Stress
: Modulus of Elasticity at 50% Max. Stress
50
PGS/SI/2013/CLJOC/06/SV-6X/FR
ATTERBERG LIMITS
21.0
21.2
21.4
19
10
65
18
20.9
17.7
21.3
18.0
22.2
19
21.8
22.4
18
21.1
2.72
18.3
113
190
17.8
120
180
UU
214
936
0.8
26750
113
175
UU
223
955
0.7
31857
95
48
22
26
170
200
22
20.1
16.4
175
250
20
19.7
16.4
175
275
24.2
24
200
250
*OEDO
24.4
21
20.7
17.1
200
260
UU
182
974
0.8
22750
24.6
21
20.8
17.2
200
260
*UU
184
977
1.2
15333
156
225
25.4
20
20.2
16.8
156
250
*UU
99
993
2.0
4853
25.6
20
20.9
17.4
156
250
UU/UUR
140
996
1.4
10000
1015
1.5
5600
1019
1.8
6145
16500
33
18
15
73
19
96
2.73
26.0
69
100
20
19.9
16.6
75
100
24
20.5
16.5
75
125
UU
84
21
21.0
17.3
75
113
*UU/UUR
110
27.2
21
20.2
16.7
69
150
27.4
22
20.8
17.0
138
350
UU
231
1031
1.4
21
20.9
17.2
163
400
*UU
330
1046
1.3
25581
23
20.6
16.7
163
400
UU
250
1050
0.8
31250
29.8
23
20.5
16.6
181
350
30.0
21
19.9
16.4
185
375
UU
272
1076
1.3
20923
33.2
48
88
33.4
48
88
48
100
UU
81
1148
2.6
3115
55
113
75
225
75
175
1224
3.2
4563
1228
2.4
5021
35
19
16
26.8
103
27.0
28.0
28.2
28.4
60
26
34
98
2.76
29.0
29.4
29.6
33.0
33.6
26
20
87
25
20.3
16.2
27
20.5
16.1
22
21.6
17.7
24
21.5
17.3
37.8
24
19.8
15.9
37.8
24
33.8
2.75
127
58
Made By :
SP
Date :
05-06-2013
Date :
03-06-2013
Plate 7c
Checked By :
CHG
37.0
37.2
37.4
37.6
P34
PRECONSOLIDATION
PRESSURE
(
)
c
CARBONATE
CONTENT
CHLORIDE
CONTENT
929
25.0
26.6
P33
kPa
24.0
26.4
P31
SULPHATE
CONTENT
3686
101
ORGANIC
CONTENT
CONFINING
EFFECTIVE
COHESION
(C')
REMOULDED
SHEAR STRENGTH
UNDRAINED
SHEAR STRENGTH
(Su)
TYPE OF
TEST
IN SITU VANE
REMOULDED
IN SITU VANE
POCKET
PENETROMETER
7286
2.7
102
*UU/UUR
26.2
P32
AG/III/PRO/F010 REV. 1
1.4
924
UU
200
23.0
25.6
P30
920
150
25.2
P29
kPa
88
155
23.6
P28
OEDOMETER
TEST
CHEMICAL TEST
22.0
23.4
P27
deg
kPa
88
155
23.2
P26
TORVANE
MOTOR VANE
REMOULDED
kPa
22.6
P25
MOTOR VANE
SPECIFIC GRAVITY
DRY
BULK
kN/m
18
21.8
P24
STRAIN/MOD.
OF ELASTICITY
E50
29
WATER CONTENT
PERCENT PASSING
No.200
PLASTICITY
INDEX
21.6
DENSITY
PLASTIC
LIMIT
DEPTH
SAMPLE No.
LIQUID
LIMIT
*
: Onshore Testing
UU
: Unconsolidated Undrained Triaxial
UUR : UU Triaxial Remoulded
CIU : Consolidated Undrained Triaxial
CD
: Consolidated Drained Triaxial
UCT : Unconfined Compression Test
SB
: Shear Box Test
: Angle of Internal Friction
: Strain at 50% Maximum Stress
: Modulus of Elasticity at 50% Max. Stress
50
PGS/SI/2013/CLJOC/06/SV-6X/FR
ATTERBERG LIMITS
41.0
26
20
67
2.72
81
225
UU
146
100
250
*UU/UUR
121
84
33
18
15
74
41.6
P35
66
45.8
49.7
17.8
21.6
18.1
19
21.3
17.9
2.70
24
20.3
16.3
25
20.6
16.4
30
36
19
17
81
UU
68
135
*UU/UUR
126
122
*SB
29
19.8
15.3
25
19.4
15.5
2.68
*CD
2.72
28
19.8
15.4
88
100
19.9
15.8
63
50
2.7
UU
54
1521
2.6
2077
53.6
23
20.2
16.4
63
50
*UU/UUR
58
32
1528
4.4
1327
90
75
29
20.3
15.7
155
150
25
20.1
16.0
138
125
UU/UUR
138
57
1601
4.2
3286
138
125
175
150
163
125
175
138
UU
145
125
*UU
225
1682
2.0
11250
135
1686
2.1
6553
UU
122
1755
3.0
4067
1907
4.4
1818
7.4
1757
57.0
37
20
17
57.8
61.0
61.3
61.5
32
20.6
15.6
32
19.8
15.0
31
18.8
14.3
150
150
65.3
28
19.8
15.4
160
138
65.5
29
19.7
15.2
160
138
26
20.0
15.8
32
19.5
14.7
30
19.7
15.1
61.7
47
24
23
98
61.9
2.75
65.0
65.1
P41
69.0
P42
73.0
69.4
69
2.70
*CD
73.1
73.3
73.5
28
23
92
2.72
73.7
40
63
40
75
57
88
40
50
UU
32
80
77.0
77.2
77.4
P44
Made By :
SP
Date :
05-06-2013
Date :
03-06-2013
Plate 7d
Checked By :
CHG
AG/III/PRO/F010 REV. 1
24
20.8
16.7
77.6
55
23
20.0
16.2
77.8
24
20.9
16.8
34
18.2
13.6
2.69
34
81.7
81.9
31
34
19
15
27
19.9
15.6
23
20.0
16.2
26
20.0
15.8
115
24
125
138
*SB
33
130
150
UU
130
2066
85.0
85.5
85.7
P46
*SB
81.0
81.4
P45
kPa
30
32
89.0
41
2.68
*SB
33
4078
PRECONSOLIDATION
PRESSURE
(
)
c
2267
3.1
CARBONATE
CONTENT
3.0
1300
CHLORIDE
CONTENT
1297
SULPHATE
CONTENT
kPa
ORGANIC
CONTENT
CONFINING
EFFECTIVE
COHESION
(C')
REMOULDED
SHEAR STRENGTH
UNDRAINED
SHEAR STRENGTH
(Su)
TYPE OF
TEST
IN SITU VANE
REMOULDED
IN SITU VANE
POCKET
PENETROMETER
135
106
26
57.6
P43
135
106
53.4
57.4
P40
113
2.69
57.2
P39
TORVANE
MOTOR VANE
REMOULDED
MOTOR VANE
SPECIFIC GRAVITY
DRY
BULK
21.9
19
53.0
53.2
P38
23
deg
kPa
49.0
49.3
P37
kPa
OEDOMETER
TEST
CHEMICAL TEST
45.0
45.4
P36
kN/m
STRAIN/MOD.
OF ELASTICITY
E50
41.4
41.2
WATER CONTENT
PERCENT PASSING
No.200
PLASTICITY
INDEX
DENSITY
PLASTIC
LIMIT
DEPTH
SAMPLE No.
LIQUID
LIMIT
*
: Onshore Testing
UU
: Unconsolidated Undrained Triaxial
UUR : UU Triaxial Remoulded
CIU : Consolidated Undrained Triaxial
CD
: Consolidated Drained Triaxial
UCT : Unconfined Compression Test
SB
: Shear Box Test
: Angle of Internal Friction
: Strain at 50% Maximum Stress
: Modulus of Elasticity at 50% Max. Stress
50
PGS/SI/2013/CLJOC/06/SV-6X/FR
ATTERBERG LIMITS
kN/m
26
20.0
15.8
89.6
89.8
P47
30
20
10
85
2.70
121
24
19.4
15.6
75
28
19.1
14.9
75
125
160
97.4
26
19.7
15.6
125
160
97.6
25
19.7
15.7
131
25
20.0
16.0
138
101.2
131
113
101.4
131
113
131
125
UU
132
131
113
*UU/UUR
148
105.2
106
125
105.4
106
125
106
125
UU
140
113
150
*UU/UUR
164
85
120
142
193
2216
7.6
125
*UU/UUR
103
76
2288
5.7
1810
145
UU
72
2292
7.0
1029
160
*UU/UUR
188
2364
3.3
5663
180
UU
241
2368
3.5
6886
2440
4.0
3300
2444
3.8
3885
2516
4.8
2917
2520
4.5
3636
2592
3.6
5110
2596
4.0
3800
2665
4.9
4274
2668
1.9
6158
33
20
13
95
2.74
136
29
22
17
95
2.74
147
32
131
101.0
36
20
16
92
26
19.9
15.8
24
19.7
15.9
2.72
83
105.0
31
19
12
89
23
20.4
16.6
2.73
23
20.5
16.6
125
150
109.4
23
19.8
16.1
126
150
109.6
24
19.4
15.6
126
175
*UU/UUR
185
23
19.9
16.1
141
150
UU
152
119
225
22
20.8
17.0
125
220
*UU/UUR
209
22
20.6
16.9
119
220
UU
117
22
20.6
16.9
106
225
109.0
41
21
20
113.0
113.2
113.4
113.6
27
18
82
113.8
2.73
129
117.0
117.5
21
21.0
17.3
42
23
20.9
17.0
26
19.6
15.5
28
19.4
15.1
29
18.8
14.5
26
18.4
14.6
18
21.0
17.8
19
20.8
17.4
121.4
Made By :
SP
Date :
05-06-2013
Date :
03-06-2013
Plate 7e
*SB
30
2.68
*CD
2.69
*SB
33
2.70
*SB
33
121.0
121.2
Checked By :
CHG
2.70
35
5.7
125.0
125.4
125.7
21
129.0
129.4
129.6
133.0
33
kPa
97.0
39
PRECONSOLIDATION
PRESSURE
(
)
c
CARBONATE
CONTENT
1868
UU/UUR
CHLORIDE
CONTENT
kPa
SULPHATE
CONTENT
ORGANIC
CONTENT
CONFINING
EFFECTIVE
COHESION
(C')
REMOULDED
SHEAR STRENGTH
24
117.3
AG/III/PRO/F010 REV. 1
UNDRAINED
SHEAR STRENGTH
(Su)
125
93.6
109.8
P57
TYPE OF
TEST
69
109.2
P56
IN SITU VANE
REMOULDED
125
15.9
105.8
P55
IN SITU VANE
69
19.4
105.6
P54
125
22
101.8
P53
130
81
93.4
101.6
P52
125
88
deg
OEDOMETER
TEST
CHEMICAL TEST
93.0
97.8
P51
125
81
16.3
97.2
P50
81
20.4
93.8
P49
kPa
25
93.2
P48
POCKET
PENETROMETER
kPa
89.2
STRAIN/MOD.
OF ELASTICITY
E50
89.4
TORVANE
MOTOR VANE
REMOULDED
MOTOR VANE
SPECIFIC GRAVITY
DRY
BULK
WATER CONTENT
PERCENT PASSING
No.200
PLASTICITY
INDEX
DENSITY
PLASTIC
LIMIT
DEPTH
SAMPLE No.
LIQUID
LIMIT
*
: Onshore Testing
UU
: Unconsolidated Undrained Triaxial
UUR : UU Triaxial Remoulded
CIU : Consolidated Undrained Triaxial
CD
: Consolidated Drained Triaxial
UCT : Unconfined Compression Test
SB
: Shear Box Test
: Angle of Internal Friction
: Strain at 50% Maximum Stress
: Modulus of Elasticity at 50% Max. Stress
50
PGS/SI/2013/CLJOC/06/SV-6X/FR
ATTERBERG LIMITS
PRECONSOLIDATION
PRESSURE
(
)
c
CARBONATE
CONTENT
CHLORIDE
CONTENT
SULPHATE
CONTENT
E50
ORGANIC
CONTENT
UU
152
75
*UU/UUR
148
70
150
SAMPLE No.
DEPTH
LIQUID
LIMIT
PLASTIC
LIMIT
PLASTICITY
INDEX
PERCENT PASSING
No.200
WATER CONTENT
BULK
DRY
SPECIFIC GRAVITY
MOTOR VANE
MOTOR VANE
REMOULDED
TORVANE
POCKET
PENETROMETER
IN SITU VANE
IN SITU VANE
REMOULDED
TYPE OF
TEST
UNDRAINED
SHEAR STRENGTH
(Su)
REMOULDED
SHEAR STRENGTH
EFFECTIVE
COHESION
(C')
CONFINING
63
55
50
*
: Onshore Testing
UU
: Unconsolidated Undrained Triaxial
UUR : UU Triaxial Remoulded
CIU : Consolidated Undrained Triaxial
CD
: Consolidated Drained Triaxial
UCT : Unconfined Compression Test
SB
: Shear Box Test
: Angle of Internal Friction
: Strain at 50% Maximum Stress
: Modulus of Elasticity at 50% Max. Stress
45
136.9
16.3
16.7
3104
20.3
20.4
128
24
18
12
62
22
136.7
30
136.5
PGS/SI/2013/CLJOC/06/SV-6X/FR
Made By :
SP
Date :
05-06-2013
Date :
03-06-2013
Plate 7f
Checked By :
CHG
AG/III/PRO/F010 REV. 1
16.9
4790
17.5
20.5
2980
21.0
21
3.1
20
133.8
5.1
133.4
kPa
P58
136.0
kPa
%
%
deg
kPa
kPa
kN/m
%
%
m
OEDOMETER
TEST
CHEMICAL TEST
STRAIN/MOD.
OF ELASTICITY
TRIAXIAL / SHEAR BOX / DIRECT SHEAR TEST
UNDRAINED SHEAR STRENGH
DENSITY
ATTERBERG LIMITS
12
UU Triaxial Onshore
UU Triaxial Offshore
Pocket Penetrometer
Torvane
Nkt
= 28
Motorvane
Nkt
= 25
10
0
0
100
200
300
400
BH SV-6X
BLOCK 15-1
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
PGS/SI/2013/CLJOC/06/SV-6X/FR
02/07/2013
Made by
SP
Checked by
CHG
Plate 8
Overconsolidation Ratio
0
10
12
14
10
20
30
40
50
Depth (m)
60
70
80
90
100
110
120
130
140
OCR deduced from Offshore UU Triaxial Test
OCR deduced from Onshore UU Triaxial Test
Date performed:
BH SV-6X
BLOCK 15-1
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
PGS/SI/2013/CLJOC/06/SV-6X/FR
01/07/2013
Made by
SP
Checked by
CHG
Plate 9
Sensitivity, St
6
8
10
12
14
10
20
30
40
50
Depth(m)
60
70
80
90
100
110
120
130
140
St deduced from CPTU with Ns= 1.0 - 4.0
St computed from Motorvane Remoulded Test
St computed from Onshore UU-UU Remoulded Triaxial Test
BH SV-6X
BLOCK 15-1
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
PGS/SI/2013/CLJOC/06/SV-6X/FR
Date performed:
01/07/2013
Made by
SP
Checked by
CHG
Plate 10
10
15
20
25
30
35
40
10
20
Very
Dense
30
40
50
Dense
Depth(m)
60
70
Medium Dense
80
90
Loose
100
110
Very
Loose
120
130
140
Date performed:
BH SV-6X
BLOCK 15-1
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
PGS/SI/2013/CLJOC/06/SV-6X/FR
26/06/2013
Made by
SP
Checked by
CHG
Prepared by
:
Plate 11
DOWNHOLE
CPT
ft
SOIL
PROFILE
DEPTH
UU Triaxial Onshore
UU Triaxial Offshore
UU Remoulded
In situ Vane
Est. from CPT:Nkt=25 (30m-132.8m)
Est. from CPT:Nkt=28 (134m-139.8m)
Design Profile
Torvane
Pocket Penetrometer
Motor Vane
Motor Vane Remoulded
Est. from CPT:Nkt=20
Est. from CPT:Nkt=25
Normally Consolidated Profile
50
100
150
200
250
300
350
400
450
Preconsolidation Pressure:
* (From Oedometer Test)
O
(From UU Triaxial Test)
SUBMERGED
3
DENSITY, ' (kN/m )
500 8
10
11
STRAIN,50 (%)
12
300
600
900
1200
1500
1800
16
32
12
48
16
20
64
24
80
28
>>
96
32
112
36
40
44
48
128
144
160
52
176
56
192
60
64
208
68
224
72
240
76
256
80
84
88
92
272
288
304
96
320
100
336
352
104
108
112
116
368
384
120
400
124
128
416
132
136
432
(Su/p')nc = 0.17
448
3
'ave = 10.08 kN/m
SUMMARY BORING
BH & CPTU SV-6X
BLOCK 15-1
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY
PGS/SI/2013/CLJOC/06/SV-6X/FR
Date Performed
17-04-2013 - 19-04-2013
Water Depth
47.1 m LAT
Coordinates
E 862,460m; N 1,144,836m
Made By/Date
SP - 03-06-2013
Plate 12
Stratum
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Soil Description
Medium dense
silty fine SAND
Stiff to very stiff
lean CLAY
Medium dense
silty fine SAND
Very stiff to hard
sandy lean CLAY
Medium dense
SILT with sand
Very stiff to hard
lean CLAY
Stiff
sandy lean CLAY
Stiff to very stiff
sandy lean CLAY
Very stiff to hard
lean CLAY
Hard
fat CLAY
Medium dense
clayey SILT
Very stiff
silty CLAY
Medium dense
SILT
Very stiff
lean CLAY with sand
Dense
sandy SILT
Stiff to very stiff
lean CLAY
Very stiff
lean CLAY
Medium dense
silty fine SAND
Dense
sandy SILT
Penetration
Submerged Undrained Shear Unit Skin
(m)
Strength, Su
Unit Weight
Friction
(kPa)/Friction
3
(kPa)
(kN/m )
angle, phi
From To
0.0
3.1
3.1
4.2
4.2
5.2
5.2
7.5
7.5
10.0
10.0
15.0
15.0
19.0
19.0
23.0
23.0
27.0
27.0
30.0
30.0
33.0
33.0
38.0
38.0
41.0
41.0
45.0
45.0
51.7
51.7
58.0
58.0
65.6
65.6
67.0
67.0
73.0
0.0
6.3
36.8
40.2
12.2
15.3
71.6
78.2
21.8
28.6
83.7
92.7
54.3
61.2
76.5
85.1
107.7
116.9
128.0
135.1
Unit End
Bearing
(MPa)
0.00
0.24
9.5
25
11.2
100
10.9
25
10.2
200
9.4
25
9.8
200
10.3
80
11.1
125
10.3
200
10.4
240
10.3
25
67.0
2.90
10.3
120
100.3
107.7
1.08
11.6
25
67.0
2.90
11.6
120
112.4
118.5
1.08
10.1
30
67.0
2.90
9.9
140
136.8
140.0
1.26
9.9
140
140.0
1.26
9.9
25
67.0
2.90
9.9
30
81.3
4.80
0.90
0.50
0.63
1.80
0.90
1.18
1.80
0.72
1.13
1.80
2.16
BH SV-6X
BLOCK 15-1
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
PGS/SI/2013/CLJOC/06/SV-6X/FR
Made by
Checked by
27-06-2013
SP
CHG
Plate 13a
Stratum
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Soil Description
Hard
cohesive SILT
Very stiff to hard
CLAY
Dense
sandy SILT
Very stiff to hard
CLAY
Dense
SILT
Dense
silty fine SAND
Dense
SILT
Very stiff
lean CLAY with sand
Dense
SILT
Very stiff to hard
lean CLAY
Very stiff
lean CLAY
Medium dense
SILT
Very stiff
lean CLAY
Very stiff to hard
CLAY
Dense
SAND
Very stiff to hard
lean CLAY
Dense
silty fine SAND
Very stiff to hard
CLAY
Dense
silty fine SAND
Penetration
Submerged Undrained Shear Unit Skin
(m)
Strength, Su
Unit Weight
Friction
(kPa)/Friction
3
(kPa)
(kN/m )
angle, phi
From To
73.0
74.3
74.3
76.3
76.3
78.4
78.4
79.2
79.2
81.0
81.0
86.0
86.0
88.6
88.6
90.8
90.8
93.0
93.0
97.0
97.0
102.5
102.5
103.4
103.4
106.0
106.0
107.3
107.3
109.0
109.0
116.3
116.3
123.0
123.0
125.0
125.0
134.0
259.1
261.2
194.7
197.1
233.2
236.4
209.5
210.6
Unit End
Bearing
(MPa)
9.5
360
9.5
200
10.8
30
10.8
220
10.8
30
81.3
4.80
9.8
30
67.0
2.90
9.8
30
81.3
4.80
10.1
200
200.0
1.80
10.1
30
81.3
4.80
9.2
160
240
160.0
240.0
1.44
2.16
9.8
160
160.0
1.44
9.8
25
67.0
2.90
10.2
160
160.0
1.44
10.2
240
240.0
2.16
10.2
30
81.3
4.80
10.1
200
200.0
1.80
10.1
30
81.3
4.80
10.1
200
200.0
1.80
10.1
30
67.0
2.90
3.24
1.80
2.52
1.98
BH SV-6X
BLOCK 15-1
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
PGS/SI/2013/CLJOC/06/SV-6X/FR
Made by
Checked by
27-06-2013
SP
CHG
Plate 13b
Stratum
39
40
Soil Description
Hard
sandy lean CLAY
Very stiff to hard
CLAY
Penetration
Submerged Undrained Shear Unit Skin
(m)
Strength, Su
Unit Weight
Friction
(kPa)/Friction
3
(kPa)
(kN/m )
angle, phi
From To
134.0
139.0
139.0
140.0
Unit End
Bearing
(MPa)
10.5
360
349.1
355.8
3.24
10.5
240
220.0
1.98
BH SV-6X
BLOCK 15-1
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
PGS/SI/2013/CLJOC/06/SV-6X/FR
Made by
Checked by
27-06-2013
SP
CHG
Plate 13c
1
50
2
100
3
150
4
200
5
250
6
300
350
7
400
10
20
30
40
50
60
70
80
90
100
110
120
130
140
BH SV-6X
BLOCK 15-1
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
PGS/SI/2013/CLJOC/06/SV-6X/FR
Made by
Checked by
04/06/2013
SP
CHG
Plate 14
10
20
30
40
50
60
70
80
10
20
30
40
50
60
70
80
90
100
110
120
130
140
Date Performed
Made by
Checked by
PGS/SI/2013/CLJOC/06/SV-6X/FR
04/06/2013
SP
CHG
Plate 15a
10
20
30
40
50
60
70
80
10
20
30
40
50
60
70
80
90
100
110
120
130
140
Date Performed
Made by
Checked by
PGS/SI/2013/CLJOC/06/SV-6X/FR
04/06/2013
SP
CHG
Plate 15b
10
20
30
40
50
60
70
80
10
20
30
40
50
60
70
80
90
100
110
120
130
140
Date Performed
Made by
Checked by
PGS/SI/2013/CLJOC/06/SV-6X/FR
04/06/2013
SP
CHG
Plate 15c
10
20
30
40
50
60
70
80
10
20
30
40
50
60
70
80
90
100
110
120
130
140
Date Performed
Made by
Checked by
PGS/SI/2013/CLJOC/06/SV-6X/FR
04/06/2013
SP
CHG
Plate 15d
Mudline
Penetration
Notes
1.
50
(%) is the axial strain at half of peak deviator stress for clays.
' is the average submerged unit weight for clays and granular soils in kN/m3.
Date performed:
BH SV-6X
BLOCK 15-01
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
PGS/SI/2013/CLJOC/06/SV-6X/FR
18/06/2013
Made by
SP
Checked by
CHG
Prepared by
:
Plate 16a
Mudline
Penetration
Medium dense
SILT
Notes
1.
50
(%) is the axial strain at half of peak deviator stress for clays.
' is the average submerged unit weight for clays and granular soils in kN/m3.
Date performed:
BH SV-6X
BLOCK 15-01
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
PGS/SI/2013/CLJOC/06/SV-6X/FR
18/06/2013
Made by
SP
Checked by
CHG
Prepared by
:
Plate 16b
762 mm
(kN/m)
(mm)
P1
Y1
P2
Y2
P3
Y3
P4
Y4
P5
Y5
P6
Y6
50/deg
Su
0.7
Sand
1.17
1.59
8.07
3.18
12.32
6.35
14.30
12.70
14.49
25.40
14.49
28.58
25o
1.0
Sand
6.35
1.59
11.86
3.18
19.01
6.35
23.23
12.70
23.82
25.40
23.82
28.58
25o
2.0
Sand
12.86
1.59
24.85
3.18
43.92
6.35
62.23
12.70
68.16
25.40
68.33
28.58
25o
3.0
Sand
19.39
1.59
37.98
3.18
70.31
6.35
110.25
12.70
131.46
25.40
132.56
28.58
25o
3.1
Sand
20.04
1.59
39.30
3.18
72.98
6.35
115.34
12.70
138.71
25.40
139.98
28.58
3.1
Clay
75.56
0.95
108.42
2.86
164.27
9.53
164.27
28.58
164.27
142.88
164.27
285.75
100.0
0.5
4.0
Clay
82.51
0.95
118.38
2.86
179.36
9.53
179.36
28.58
179.36
142.88
179.36
285.75
100.0
0.5
4.2
Clay
84.05
0.95
120.59
2.86
182.71
9.53
182.71
28.58
182.71
142.88
182.71
285.75
100.0
4.2
Sand
27.23
1.59
53.83
3.18
102.93
6.35
176.28
12.70
236.28
25.40
241.47
28.58
25o
5.0
Sand
32.45
1.59
64.34
3.18
124.41
6.35
220.54
12.70
314.42
25.40
324.41
28.58
25o
5.2
Sand
33.75
1.59
66.96
3.18
129.76
6.35
231.62
12.70
334.77
25.40
346.21
28.58
5.2
Clay
174.17
0.95
249.90
2.86
378.63
9.53
378.63
28.58
378.63
142.88
378.63
285.75
200.0
0.5
6.0
Clay
184.73
0.95
265.05
2.86
401.59
9.53
401.59
28.58
401.59
142.88
401.59
285.75
200.0
0.5
7.0
Clay
197.93
0.95
283.99
2.86
430.28
9.53
430.28
28.58
430.28
142.88
430.28
285.75
200.0
0.5
7.5
Clay
204.53
0.95
293.46
2.86
444.63
9.53
444.63
28.58
444.63
142.88
444.63
285.75
200.0
7.5
Silt
48.74
1.59
97.04
3.18
190.63
6.35
356.37
12.70
572.92
25.40
605.29
28.58
25o
8.0
Silt
52.00
1.59
103.57
3.18
203.81
6.35
383.37
12.70
626.49
25.40
664.39
28.58
25o
9.0
Silt
58.51
1.59
116.58
3.18
229.74
6.35
434.45
12.70
720.46
25.40
766.74
28.58
25o
10 0
10.0
Silt
65.01
65 01
1.59
1 59
129.52
129 52
3.18
3 18
255.22
255 22
6.35
6 35
482.38
482 38
12.70
12 70
798.79
798 79
25.40
25 40
849.80
849 80
28.58
28 58
25o
10.0
Clay
237.40
0.95
340.61
2.86
516.08
9.53
516.08
28.58
516.08
142.88
516.08
285.75
200.0
0.5
11.0
Clay
250.62
0.95
359.58
2.86
544.82
9.53
544.82
28.58
544.82
142.88
544.82
285.75
200.0
0.5
12.0
Clay
263.83
0.95
378.54
2.86
573.55
9.53
573.55
28.58
573.55
142.88
573.55
285.75
200.0
0.5
13.0
Clay
277.05
0.95
397.51
2.86
602.28
9.53
602.28
28.58
602.28
142.88
602.28
285.75
200.0
0.5
14.0
Clay
290.27
0.95
416.47
2.86
631.02
9.53
631.02
28.58
631.02
142.88
631.02
285.75
200.0
0.5
15.0
Clay
315.47
0.95
452.63
2.86
685.80
9.53
685.80
28.58
685.80
142.88
685.80
285.75
200.0
0.5
15.0
Clay
126.19
1.91
181.05
5.72
274.32
19.05
395.02
57.15
395.02
285.75
395.02
571.50
80.0
1.0
16.0
Clay
126.19
1.91
181.05
5.72
274.32
19.05
395.02
57.15
395.02
285.75
395.02
571.50
80.0
1.0
17.0
Clay
126.19
1.91
181.05
5.72
274.32
19.05
395.02
57.15
395.02
285.75
395.02
571.50
80.0
1.0
18.0
Clay
126.19
1.91
181.05
5.72
274.32
19.05
395.02
57.15
395.02
285.75
395.02
571.50
80.0
1.0
19.0
Clay
126.19
1.91
181.05
5.72
274.32
19.05
395.02
57.15
395.02
285.75
395.02
571.50
80.0
1.0
19.0
Clay
197.17
0.95
282.89
2.86
428.63
9.53
428.63
28.58
428.63
142.88
428.63
285.75
125.0
0.5
20.0
Clay
197.17
0.95
282.89
2.86
428.63
9.53
428.63
28.58
428.63
142.88
428.63
285.75
125.0
0.5
21.0
Clay
197.17
0.95
282.89
2.86
428.63
9.53
428.63
28.58
428.63
142.88
428.63
285.75
125.0
0.5
22.0
Clay
197.17
0.95
282.89
2.86
428.63
9.53
428.63
28.58
428.63
142.88
428.63
285.75
125.0
0.5
23.0
Clay
197.17
0.95
282.89
2.86
428.63
9.53
428.63
28.58
428.63
142.88
428.63
285.75
125.0
0.5
23.0
Clay
315.47
0.95
452.63
2.86
685.80
9.53
685.80
28.58
685.80
142.88
685.80
285.75
200.0
0.5
24.0
Clay
315.47
0.95
452.63
2.86
685.80
9.53
685.80
28.58
685.80
142.88
685.80
285.75
200.0
0.5
25.0
Clay
315.47
0.95
452.63
2.86
685.80
9.53
685.80
28.58
685.80
142.88
685.80
285.75
200.0
0.5
26.0
Clay
315.47
0.95
452.63
2.86
685.80
9.53
685.80
28.58
685.80
142.88
685.80
285.75
200.0
0.5
27.0
Clay
315.47
0.95
452.63
2.86
685.80
9.53
685.80
28.58
685.80
142.88
685.80
285.75
200.0
0.5
27.0
Clay
378.56
0.95
543.15
2.86
822.96
9.53
822.96
28.58
822.96
142.88
822.96
285.75
240.0
0.5
25o
0.5
25o
0.5
Date Performed
10/06/2013
Made by
SP
Plate 17a
762 mm
(kN/m)
(mm)
P1
Y1
P2
Y2
P3
Y3
P4
Y4
P5
Y5
50/deg
P6
Y6
Su
240.0
30.0
Clay
378.56
0.95
543.15
2.86
822.96
9.53
822.96
28.58
822.96
142.88
822.96
285.75
30.0
Silt
195.04
1.59
388.74
3.18
766.98
6.35
1456.41
12.70
2443.64
25.40
2608.11
28.58
25o
0.5
33.0
Silt
214.54
1.59
427.61
3.18
843.68
6.35
1602.06
12.70
2688.00
25.40
2868.92
28.58
25o
33.0
Clay
189.28
0.95
271.58
2.86
411.48
9.53
411.48
28.58
411.48
142.88
411.48
285.75
120.0
38.0
Clay
189.28
0.95
271.58
2.86
411.48
9.53
411.48
28.58
411.48
142.88
411.48
285.75
120.0
38.0
Silt
247.06
1.59
492.47
3.18
972.08
6.35
1848.79
12.70
3116.14
25.40
3329.67
28.58
41.0
Silt
266.57
1.59
531.39
3.18
1049.11
6.35
1996.76
12.70
3372.76
25.40
3605.83
28.58
41.0
Clay
189.28
0.95
271.58
2.86
411.48
9.53
411.48
28.58
411.48
142.88
411.48
285.75
120.0
45.0
Clay
189.28
0.95
271.58
2.86
411.48
9.53
411.48
28.58
411.48
142.88
411.48
285.75
120.0
45.0
Silt
691.67
1.59
1375.76
3.18
2692.84
6.35
4970.66
12.70
7739.53
25.40
8119.80
28.58
30o
51.7
Silt
794.63
1.59
1580.42
3.18
3092.45
6.35
5702.03
12.70
8854.76
25.40
9284.64
28.58
30o
51.7
Clay
220.83
0.95
316.84
2.86
480.06
9.53
480.06
28.58
480.06
142.88
480.06
285.75
140.0
0.5
58.0
Clay
220.83
0.95
316.84
2.86
480.06
9.53
480.06
28.58
480.06
142.88
480.06
285.75
140.0
0.5
58.0
Clay
220.83
0.95
316.84
2.86
480.06
9.53
480.06
28.58
480.06
142.88
480.06
285.75
140.0
0.5
65.6
Clay
220.83
0.95
316.84
2.86
480.06
9.53
480.06
28.58
480.06
142.88
480.06
285.75
140.0
65.6
Sand
426.48
1.59
850.05
3.18
1677.23
6.35
3185.32
12.70
5346.68
25.40
5707.14
28.58
25o
67.0
Sand
435.59
1.59
868.19
3.18
1712.97
6.35
3252.94
12.70
5458.90
25.40
5826.57
28.58
25o
67 0
67.0
Silt
1029 75
1029.75
1 59
1.59
2047 77
2047.77
3 18
3.18
4004 92
4004.92
6 35
6.35
7371 78
7371.78
12 70
12.70
11400 36
11400.36
25 40
25.40
11943 49
11943.49
28 58
28.58
30o
73.0
Silt
1121.93
1.59
2230.94
3.18
4361.90
6.35
8021.07
12.70
12375.71
25.40
12959.09
28.58
30o
73.0
Silt
567.84
0.95
814.73
2.86
1234.44
9.53
1234.44
28.58
1234.44
142.88
1234.44
285.75
360.0
0.5
74.3
Silt
567.84
0.95
814.73
2.86
1234.44
9.53
1234.44
28.58
1234.44
142.88
1234.44
285.75
360.0
0.5
74.3
Clay
315.47
0.95
452.63
2.86
685.80
9.53
685.80
28.58
685.80
142.88
685.80
285.75
200.0
0.5
76.3
Clay
315.47
0.95
452.63
2.86
685.80
9.53
685.80
28.58
685.80
142.88
685.80
285.75
200.0
76.3
Silt
1172.64
1.59
2331.73
3.18
4558.64
6.35
8380.76
12.70
12923.01
25.40
13530.53
28.58
30o
78.4
Silt
1204.92
1.59
2395.89
3.18
4684.00
6.35
8610.74
12.70
13275.83
25.40
13899.55
28.58
30o
78.4
Clay
347.01
0.95
497.89
2.86
754.38
9.53
754.38
28.58
754.38
142.88
754.38
285.75
220.0
79.2
Clay
347.01
0.95
497.89
2.86
754.38
9.53
754.38
28.58
754.38
142.88
754.38
285.75
220.0
79.2
Silt
1217.21
1.59
2420.36
3.18
4731.96
6.35
8699.66
12.70
13415.70
25.40
14046.59
28.58
30o
81.0
Silt
1244.87
1.59
2475.33
3.18
4839.24
6.35
8895.63
12.70
13713.33
25.40
14357.23
28.58
30o
81.0
Sand
1244.87
1.59
2475.33
3.18
4839.24
6.35
8895.63
12.70
13713.33
25.40
14357.23
28.58
30o
86.0
Sand
1321.50
1.59
2626.37
3.18
5124.69
6.35
9358.97
12.70
14209.21
25.40
14830.59
28.58
30o
86.0
Silt
1321.50
1.59
2626.37
3.18
5124.69
6.35
9358.97
12.70
14209.21
25.40
14830.59
28.58
30o
88.6
Silt
1361.45
1.59
2705.82
3.18
5279.93
6.35
9643.88
12.70
14646.67
25.40
15288.19
28.58
30o
88.6
Clay
315.47
0.95
452.63
2.86
685.80
9.53
685.80
28.58
685.80
142.88
685.80
285.75
200.0
90.8
Clay
315.47
0.95
452.63
2.86
685.80
9.53
685.80
28.58
685.80
142.88
685.80
285.75
200.0
90.8
Silt
1395.26
1.59
2773.04
3.18
5411.28
6.35
9884.95
12.70
15016.82
25.40
15675.39
28.58
30o
93.0
Silt
1429.06
1.59
2840.16
3.18
5541.86
6.35
10121.05
12.70
15366.98
25.40
16039.15
28.58
30o
93.0
Clay
252.37
0.95
362.10
2.86
548.64
9.53
548.64
28.58
548.64
142.88
548.64
285.75
160.0
0.5
97.0
Clay
378.56
0.95
543.15
2.86
822.96
9.53
822.96
28.58
822.96
142.88
822.96
285.75
240.0
0.5
97.0
Clay
252.37
0.95
362.10
2.86
548.64
9.53
548.64
28.58
548.64
142.88
548.64
285.75
160.0
0.5
102.5
Clay
167.20
0.95
239.89
2.86
363.47
9.53
363.47
28.58
363.47
142.88
363.47
285.75
106.0
0.5
0.5
0.5
25o
25o
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
Date Performed
10/06/2013
Made by
SP
Plate 17b
762 mm
(mm)
P1
Y1
P2
Y2
P3
Y3
P4
Y4
P5
Y5
P6
Y6
50/deg
Su
102.5
Silt
666.30
1.59
1327.55
3.18
2615.62
6.35
4941.65
12.70
8173.62
25.40
8693.18
28.58
25o
103.4
Silt
672.15
1.59
1339.21
3.18
2638.59
6.35
4985.04
12.70
8245.38
25.40
8769.51
28.58
25o
103.4
Clay
252.37
0.95
362.10
2.86
548.64
9.53
548.64
28.58
548.64
142.88
548.64
285.75
160.0
0.5
106.0
Clay
252.37
0.95
362.10
2.86
548.64
9.53
548.64
28.58
548.64
142.88
548.64
285.75
160.0
0.5
106.0
Clay
378.56
0.95
543.15
2.86
822.96
9.53
822.96
28.58
822.96
142.88
822.96
285.75
240.0
0.5
107.3
Clay
378.56
0.95
543.15
2.86
822.96
9.53
822.96
28.58
822.96
142.88
822.96
285.75
240.0
107.3
Sand
1648.81
1.59
3276.94
3.18
6394.56
6.35
11680.87
12.70
17744.21
25.40
18522.21
28.58
30o
109.0
Sand
1674.93
1.59
3328.89
3.18
6496.13
6.35
11867.58
12.70
18031.95
25.40
18823.41
28.58
30o
109.0
Clay
315.47
0.95
452.63
2.86
685.80
9.53
685.80
28.58
685.80
142.88
685.80
285.75
200.0
116.3
Clay
315.47
0.95
452.63
2.86
685.80
9.53
685.80
28.58
685.80
142.88
685.80
285.75
200.0
116.3
Sand
1787.12
1.59
3551.94
3.18
6931.98
6.35
12667.50
12.70
19260.12
25.40
20108.15
28.58
30o
123.0
Sand
1890.09
1.59
3756.66
3.18
7332.01
6.35
13401.64
12.70
20387.31
25.40
21287.25
28.58
30o
123.0
Clay
315.47
0.95
452.63
2.86
685.80
9.53
685.80
28.58
685.80
142.88
685.80
285.75
200.0
125.0
Clay
315.47
0.95
452.63
2.86
685.80
9.53
685.80
28.58
685.80
142.88
685.80
285.75
200.0
125.0
Sand
1920.82
1.59
3817.77
3.18
7451.42
6.35
13620.79
12.70
20723.77
25.40
21639.21
28.58
134.0
Sand
2059.14
1.59
4092.76
3.18
7988.77
6.35
14606.93
12.70
22237.84
25.40
23223.01
28.58
134.0
Clay
567.84
0.95
814.73
2.86
1234.44
9.53
1234.44
28.58
1234.44
142.88
1234.44
285.75
360.0
139 0
139.0
Clay
567 84
567.84
0 95
0.95
814 73
814.73
2 86
2.86
1234 44
1234.44
9 53
9.53
1234 44
1234.44
28 58
28.58
1234 44
1234.44
142 88
142.88
1234 44
1234.44
285 75
285.75
360 0
360.0
05
0.5
139.0
Clay
347.01
0.95
497.89
2.86
754.38
9.53
754.38
28.58
754.38
142.88
754.38
285.75
220.0
0.5
140.0
Clay
347.01
0.95
497.89
2.86
754.38
9.53
754.38
28.58
754.38
142.88
754.38
285.75
220.0
0.5
0.5
0.5
0.5
0.5
0.5
30o
30o
0.5
Date Performed
10/06/2013
Made by
SP
Plate 17c
914 mm
(kN/m)
(mm)
P1
Y1
P2
Y2
P3
Y3
P4
Y4
P5
Y5
P6
Y6
50/deg
Su
0.7
Sand
1.40
1.90
9.55
3.81
14.25
7.62
16.21
15.23
16.36
30.47
16.36
34.28
25o
1.0
Sand
7.59
1.90
14.03
3.81
21.91
7.62
26.03
15.23
26.49
30.47
26.50
34.28
25o
2.0
Sand
15.39
1.90
29.49
3.81
50.86
7.62
68.98
15.23
73.66
30.47
73.75
34.28
25o
3.0
Sand
23.21
1.90
45.21
3.81
82.10
7.62
123.06
15.23
140.54
30.47
141.24
34.28
25o
3.1
Sand
23.99
1.90
46.79
3.81
85.28
7.62
128.87
15.23
148.24
30.47
149.05
34.28
3.1
Clay
87.08
1.14
124.94
3.43
189.31
11.43
189.31
34.28
189.31
171.38
189.31
342.75
100.0
0.5
4.0
Clay
94.38
1.14
135.41
3.43
205.17
11.43
205.17
34.28
205.17
171.38
205.17
342.75
100.0
0.5
4.2
Clay
96.00
1.14
137.73
3.43
208.69
11.43
208.69
34.28
208.69
171.38
208.69
342.75
100.0
4.2
Sand
32.62
1.90
64.25
3.81
121.27
7.62
200.03
15.23
253.48
30.47
257.19
34.28
25o
5.0
Sand
38.88
1.90
76.88
3.81
147.11
7.62
252.45
15.23
339.49
30.47
347.11
34.28
25o
5.2
Sand
40.45
1.90
80.03
3.81
153.56
7.62
265.65
15.23
362.14
30.47
371.00
34.28
5.2
Clay
196.98
1.14
282.63
3.43
428.22
11.43
428.22
34.28
428.22
171.38
428.22
342.75
200.0
0.5
6.0
Clay
207.81
1.14
298.17
3.43
451.77
11.43
451.77
34.28
451.77
171.38
451.77
342.75
200.0
0.5
7.0
Clay
221.35
1.14
317.59
3.43
481.20
11.43
481.20
34.28
481.20
171.38
481.20
342.75
200.0
0.5
7.5
Clay
228.12
1.14
327.31
3.43
495.92
11.43
495.92
34.28
495.92
171.38
495.92
342.75
200.0
7.5
Silt
58.43
1.90
116.14
3.81
226.74
7.62
414.79
15.23
632.25
30.47
660.41
34.28
25o
8.0
Silt
62.34
1.90
123.98
3.81
242.59
7.62
447.22
15.23
694.19
30.47
727.83
34.28
25o
9.0
Silt
70.15
1.90
139.66
3.81
274.26
7.62
512.11
15.23
820.77
30.47
866.54
34.28
25o
10 0
10.0
Silt
77.97
77 97
1.90
1 90
155.33
155 33
3.81
3 81
305.90
305 90
7.62
7 62
576.97
576 97
15.23
15 23
949.95
949 95
30.47
30 47
1009.22
1009 22
34.28
34 28
25o
10.0
Clay
261.81
1.14
375.65
3.43
569.16
11.43
569.16
34.28
569.16
171.38
569.16
342.75
200.0
0.5
11.0
Clay
275.37
1.14
395.10
3.43
598.64
11.43
598.64
34.28
598.64
171.38
598.64
342.75
200.0
0.5
12.0
Clay
288.93
1.14
414.56
3.43
628.12
11.43
628.12
34.28
628.12
171.38
628.12
342.75
200.0
0.5
13.0
Clay
302.49
1.14
434.01
3.43
657.60
11.43
657.60
34.28
657.60
171.38
657.60
342.75
200.0
0.5
14.0
Clay
316.05
1.14
453.47
3.43
687.07
11.43
687.07
34.28
687.07
171.38
687.07
342.75
200.0
0.5
15.0
Clay
378.40
1.14
542.92
3.43
822.60
11.43
822.60
34.28
822.60
171.38
822.60
342.75
200.0
0.5
15.0
Clay
151.36
2.29
217.17
6.86
329.04
22.85
473.82
68.55
473.82
342.75
473.82
685.50
80.0
1.0
16.0
Clay
151.36
2.29
217.17
6.86
329.04
22.85
473.82
68.55
473.82
342.75
473.82
685.50
80.0
1.0
17.0
Clay
151.36
2.29
217.17
6.86
329.04
22.85
473.82
68.55
473.82
342.75
473.82
685.50
80.0
1.0
18.0
Clay
151.36
2.29
217.17
6.86
329.04
22.85
473.82
68.55
473.82
342.75
473.82
685.50
80.0
1.0
19.0
Clay
151.36
2.29
217.17
6.86
329.04
22.85
473.82
68.55
473.82
342.75
473.82
685.50
80.0
1.0
19.0
Clay
236.50
1.14
339.32
3.43
514.13
11.43
514.13
34.28
514.13
171.38
514.13
342.75
125.0
0.5
20.0
Clay
236.50
1.14
339.32
3.43
514.13
11.43
514.13
34.28
514.13
171.38
514.13
342.75
125.0
0.5
21.0
Clay
236.50
1.14
339.32
3.43
514.13
11.43
514.13
34.28
514.13
171.38
514.13
342.75
125.0
0.5
22.0
Clay
236.50
1.14
339.32
3.43
514.13
11.43
514.13
34.28
514.13
171.38
514.13
342.75
125.0
0.5
23.0
Clay
236.50
1.14
339.32
3.43
514.13
11.43
514.13
34.28
514.13
171.38
514.13
342.75
125.0
0.5
23.0
Clay
378.40
1.14
542.92
3.43
822.60
11.43
822.60
34.28
822.60
171.38
822.60
342.75
200.0
0.5
24.0
Clay
378.40
1.14
542.92
3.43
822.60
11.43
822.60
34.28
822.60
171.38
822.60
342.75
200.0
0.5
25.0
Clay
378.40
1.14
542.92
3.43
822.60
11.43
822.60
34.28
822.60
171.38
822.60
342.75
200.0
0.5
26.0
Clay
378.40
1.14
542.92
3.43
822.60
11.43
822.60
34.28
822.60
171.38
822.60
342.75
200.0
0.5
27.0
Clay
378.40
1.14
542.92
3.43
822.60
11.43
822.60
34.28
822.60
171.38
822.60
342.75
200.0
0.5
27.0
Clay
454.08
1.14
651.50
3.43
987.12
11.43
987.12
34.28
987.12
171.38
987.12
342.75
240.0
0.5
25o
0.5
25o
0.5
Date Performed
10/06/2013
Made by
SP
Plate 17d
914 mm
(kN/m)
(mm)
P1
Y1
P2
Y2
P3
Y3
P4
Y4
P5
Y5
50/deg
P6
Y6
Su
240.0
30.0
Clay
454.08
1.14
651.50
3.43
987.12
11.43
987.12
34.28
987.12
171.38
987.12
342.75
30.0
Silt
233.94
1.90
466.28
3.81
919.98
7.62
1746.93
15.23
2931.09
30.47
3128.37
34.28
25o
0.5
33.0
Silt
257.34
1.90
512.91
3.81
1011.98
7.62
1921.63
15.23
3224.19
30.47
3441.20
34.28
25o
33.0
Clay
227.04
1.14
325.75
3.43
493.56
11.43
493.56
34.28
493.56
171.38
493.56
342.75
120.0
38.0
Clay
227.04
1.14
325.75
3.43
493.56
11.43
493.56
34.28
493.56
171.38
493.56
342.75
120.0
38.0
Silt
296.34
1.90
590.71
3.81
1165.98
7.62
2217.58
15.23
3737.73
30.47
3993.86
34.28
41.0
Silt
319.74
1.90
637.39
3.81
1258.38
7.62
2395.07
15.23
4045.55
30.47
4325.10
34.28
41.0
Clay
227.04
1.14
325.75
3.43
493.56
11.43
493.56
34.28
493.56
171.38
493.56
342.75
120.0
45.0
Clay
227.04
1.14
325.75
3.43
493.56
11.43
493.56
34.28
493.56
171.38
493.56
342.75
120.0
45.0
Silt
829.64
1.90
1650.19
3.81
3229.99
7.62
5962.18
15.23
9283.37
30.47
9739.50
34.28
30o
51.7
Silt
953.14
1.90
1895.68
3.81
3709.31
7.62
6839.45
15.23
10621.06
30.47
11136.69
34.28
30o
51.7
Clay
264.88
1.14
380.04
3.43
575.82
11.43
575.82
34.28
575.82
171.38
575.82
342.75
140.0
0.5
58.0
Clay
264.88
1.14
380.04
3.43
575.82
11.43
575.82
34.28
575.82
171.38
575.82
342.75
140.0
0.5
58.0
Clay
264.88
1.14
380.04
3.43
575.82
11.43
575.82
34.28
575.82
171.38
575.82
342.75
140.0
0.5
65.6
Clay
264.88
1.14
380.04
3.43
575.82
11.43
575.82
34.28
575.82
171.38
575.82
342.75
140.0
65.6
Sand
511.56
1.90
1019.62
3.81
2011.79
7.62
3820.71
15.23
6413.21
30.47
6845.57
34.28
25o
67.0
Sand
522.47
1.90
1041.37
3.81
2054.66
7.62
3901.82
15.23
6547.81
30.47
6988.83
34.28
25o
67 0
67.0
Silt
1235 15
1235.15
1 90
1.90
2456 25
2456.25
3 81
3.81
4803 80
4803.80
7 62
7.62
8842 27
8842.27
15 23
15.23
13674 44
13674.44
30 47
30.47
14325 92
14325.92
34 28
34.28
30o
73.0
Silt
1345.73
1.90
2675.95
3.81
5232.00
7.62
9621.08
15.23
14844.36
30.47
15544.11
34.28
30o
73.0
Silt
681.11
1.14
977.25
3.43
1480.68
11.43
1480.68
34.28
1480.68
171.38
1480.68
342.75
360.0
0.5
74.3
Silt
681.11
1.14
977.25
3.43
1480.68
11.43
1480.68
34.28
1480.68
171.38
1480.68
342.75
360.0
0.5
74.3
Clay
378.40
1.14
542.92
3.43
822.60
11.43
822.60
34.28
822.60
171.38
822.60
342.75
200.0
0.5
76.3
Clay
378.40
1.14
542.92
3.43
822.60
11.43
822.60
34.28
822.60
171.38
822.60
342.75
200.0
76.3
Silt
1406.56
1.90
2796.85
3.81
5467.98
7.62
10052.51
15.23
15500.82
30.47
16229.53
34.28
30o
78.4
Silt
1445.27
1.90
2873.81
3.81
5618.34
7.62
10328.36
15.23
15924.02
30.47
16672.16
34.28
30o
78.4
Clay
416.24
1.14
597.21
3.43
904.86
11.43
904.86
34.28
904.86
171.38
904.86
342.75
220.0
79.2
Clay
416.24
1.14
597.21
3.43
904.86
11.43
904.86
34.28
904.86
171.38
904.86
342.75
220.0
79.2
Silt
1460.02
1.90
2903.16
3.81
5675.87
7.62
10435.02
15.23
16091.80
30.47
16848.54
34.28
30o
81.0
Silt
1493.19
1.90
2969.10
3.81
5804.55
7.62
10670.09
15.23
16448.80
30.47
17221.14
34.28
30o
81.0
Sand
1493.19
1.90
2969.10
3.81
5804.55
7.62
10670.09
15.23
16448.80
30.47
17221.14
34.28
30o
86.0
Sand
1585.10
1.90
3150.27
3.81
6146.94
7.62
11225.85
15.23
17043.59
30.47
17788.92
34.28
30o
86.0
Silt
1585.10
1.90
3150.27
3.81
6146.94
7.62
11225.85
15.23
17043.59
30.47
17788.92
34.28
30o
88.6
Silt
1633.03
1.90
3245.56
3.81
6333.14
7.62
11567.59
15.23
17568.31
30.47
18337.80
34.28
30o
88.6
Clay
378.40
1.14
542.92
3.43
822.60
11.43
822.60
34.28
822.60
171.38
822.60
342.75
200.0
90.8
Clay
378.40
1.14
542.92
3.43
822.60
11.43
822.60
34.28
822.60
171.38
822.60
342.75
200.0
90.8
Silt
1673.58
1.90
3326.19
3.81
6490.70
7.62
11856.76
15.23
18012.30
30.47
18802.24
34.28
30o
93.0
Silt
1714.12
1.90
3406.70
3.81
6647.33
7.62
12139.94
15.23
18432.31
30.47
19238.56
34.28
30o
93.0
Clay
302.72
1.14
434.33
3.43
658.08
11.43
658.08
34.28
658.08
171.38
658.08
342.75
160.0
0.5
97.0
Clay
454.08
1.14
651.50
3.43
987.12
11.43
987.12
34.28
987.12
171.38
987.12
342.75
240.0
0.5
97.0
Clay
302.72
1.14
434.33
3.43
658.08
11.43
658.08
34.28
658.08
171.38
658.08
342.75
160.0
0.5
102.5
Clay
200.55
1.14
287.75
3.43
435.98
11.43
435.98
34.28
435.98
171.38
435.98
342.75
106.0
0.5
0.5
0.5
25o
25o
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
Date Performed
10/06/2013
Made by
SP
Plate 17e
914 mm
(mm)
P1
Y1
P2
Y2
P3
Y3
P4
Y4
P5
Y5
P6
Y6
Su
50/deg
102.5
Silt
799.21
1.90
1592.37
3.81
3137.37
7.62
5927.39
15.23
9804.05
30.47
10427.26
34.28
25o
103.4
Silt
806.23
1.90
1606.35
3.81
3164.92
7.62
5979.43
15.23
9890.13
30.47
10518.81
34.28
25o
103.4
Clay
302.72
1.14
434.33
3.43
658.08
11.43
658.08
34.28
658.08
171.38
658.08
342.75
160.0
0.5
106.0
Clay
302.72
1.14
434.33
3.43
658.08
11.43
658.08
34.28
658.08
171.38
658.08
342.75
160.0
0.5
106.0
Clay
454.08
1.14
651.50
3.43
987.12
11.43
987.12
34.28
987.12
171.38
987.12
342.75
240.0
0.5
107.3
Clay
454.08
1.14
651.50
3.43
987.12
11.43
987.12
34.28
987.12
171.38
987.12
342.75
240.0
107.3
Sand
1977.70
1.90
3930.61
3.81
7670.11
7.62
14010.92
15.23
21283.74
30.47
22216.93
34.28
30o
109.0
Sand
2009.04
1.90
3992.92
3.81
7791.94
7.62
14234.87
15.23
21628.87
30.47
22578.22
34.28
30o
109.0
Clay
378.40
1.14
542.92
3.43
822.60
11.43
822.60
34.28
822.60
171.38
822.60
342.75
200.0
116.3
Clay
378.40
1.14
542.92
3.43
822.60
11.43
822.60
34.28
822.60
171.38
822.60
342.75
200.0
116.3
Sand
2143.61
1.90
4260.47
3.81
8314.74
7.62
15194.34
15.23
23102.04
30.47
24119.22
34.28
30o
123.0
Sand
2267.11
1.90
4506.02
3.81
8794.57
7.62
16074.94
15.23
24454.07
30.47
25533.52
34.28
30o
123.0
Clay
378.40
1.14
542.92
3.43
822.60
11.43
822.60
34.28
822.60
171.38
822.60
342.75
200.0
125.0
Clay
378.40
1.14
542.92
3.43
822.60
11.43
822.60
34.28
822.60
171.38
822.60
342.75
200.0
125.0
Sand
2303.98
1.90
4579.32
3.81
8937.80
7.62
16337.80
15.23
24857.65
30.47
25955.69
34.28
134.0
Sand
2469.88
1.90
4909.16
3.81
9582.33
7.62
17520.65
15.23
26673.74
30.47
27855.42
34.28
134.0
Clay
681.11
1.14
977.25
3.43
1480.68
11.43
1480.68
34.28
1480.68
171.38
1480.68
342.75
360.0
139 0
139.0
Clay
681 11
681.11
1 14
1.14
977 25
977.25
3 43
3.43
1480 68
1480.68
11 43
11.43
1480 68
1480.68
34 28
34.28
1480 68
1480.68
171 38
171.38
1480 68
1480.68
342 75
342.75
360 0
360.0
05
0.5
139.0
Clay
416.24
1.14
597.21
3.43
904.86
11.43
904.86
34.28
904.86
171.38
904.86
342.75
220.0
0.5
140.0
Clay
416.24
1.14
597.21
3.43
904.86
11.43
904.86
34.28
904.86
171.38
904.86
342.75
220.0
0.5
0.5
0.5
0.5
0.5
0.5
30o
30o
0.5
Date Performed
10/06/2013
Made by
SP
Plate 17f
1219 mm
(kN/m)
(mm)
P1
Y1
P2
Y2
P3
Y3
P4
Y4
P5
Y5
P6
Y6
50/deg
Su
0.7
Sand
1.86
2.54
12.47
5.08
18.02
10.16
20.00
20.32
20.12
40.63
20.12
45.71
25o
1.0
Sand
10.06
2.54
18.29
5.08
27.52
10.16
31.53
20.32
31.86
40.63
31.86
45.71
25o
2.0
Sand
20.41
2.54
38.58
5.08
63.86
10.16
81.33
20.32
84.50
40.63
84.54
45.71
25o
3.0
Sand
30.84
2.54
59.41
5.08
104.12
10.16
145.24
20.32
157.52
40.63
157.83
45.71
25o
3.1
Sand
31.88
2.54
61.51
5.08
108.26
10.16
152.22
20.32
165.91
40.63
166.27
45.71
3.1
Clay
110.19
1.52
158.10
4.57
239.55
15.24
239.55
45.71
239.55
228.56
239.55
457.13
100.0
0.5
4.0
Clay
118.19
1.52
169.58
4.57
256.94
15.24
256.94
45.71
256.94
228.56
256.94
457.13
100.0
0.5
4.2
Clay
119.97
1.52
172.13
4.57
260.81
15.24
260.81
45.71
260.81
228.56
260.81
457.13
100.0
4.2
Sand
43.40
2.54
84.85
5.08
156.02
10.16
240.72
20.32
282.33
40.63
284.29
45.71
25o
5.0
Sand
51.75
2.54
101.72
5.08
190.49
10.16
307.64
20.32
379.38
40.63
383.80
45.71
25o
5.2
Sand
53.84
2.54
105.93
5.08
199.10
10.16
324.68
20.32
405.29
40.63
410.53
45.71
5.2
Clay
242.76
1.52
348.31
4.57
527.74
15.24
527.74
45.71
527.74
228.56
527.74
457.13
200.0
0.5
6.0
Clay
254.14
1.52
364.63
4.57
552.47
15.24
552.47
45.71
552.47
228.56
552.47
457.13
200.0
0.5
7.0
Clay
268.36
1.52
385.03
4.57
583.38
15.24
583.38
45.71
583.38
228.56
583.38
457.13
200.0
0.5
7.5
Clay
275.47
1.52
395.23
4.57
598.84
15.24
598.84
45.71
598.84
228.56
598.84
457.13
200.0
7.5
Silt
77.84
2.54
154.15
5.08
296.85
10.16
519.39
20.32
722.35
40.63
742.29
45.71
25o
8.0
Silt
83.05
2.54
164.62
5.08
318.06
10.16
562.27
20.32
797.29
40.63
821.86
45.71
25o
9.0
Silt
93.48
2.54
185.56
5.08
360.45
10.16
648.51
20.32
952.75
40.63
988.21
45.71
25o
10 0
10.0
Silt
103.90
103 90
2.54
2 54
206.48
206 48
5.08
5 08
402.82
402 82
10.16
10 16
735.12
735 12
20.32
20 32
1114.30
1114 30
40.63
40 63
1162.65
1162 65
45.71
45 71
25o
10.0
Clay
310.80
1.52
445.94
4.57
675.66
15.24
675.66
45.71
675.66
228.56
675.66
457.13
200.0
0.5
11.0
Clay
325.05
1.52
466.38
4.57
706.64
15.24
706.64
45.71
706.64
228.56
706.64
457.13
200.0
0.5
12.0
Clay
339.30
1.52
486.82
4.57
737.61
15.24
737.61
45.71
737.61
228.56
737.61
457.13
200.0
0.5
13.0
Clay
353.55
1.52
507.26
4.57
768.58
15.24
768.58
45.71
768.58
228.56
768.58
457.13
200.0
0.5
14.0
Clay
367.80
1.52
527.71
4.57
799.56
15.24
799.56
45.71
799.56
228.56
799.56
457.13
200.0
0.5
15.0
Clay
504.67
1.52
724.09
4.57
1097.10
15.24
1097.10
45.71
1097.10
228.56
1097.10
457.13
200.0
0.5
15.0
Clay
201.87
3.05
289.63
9.14
438.84
30.48
631.93
91.43
631.93
457.13
631.93
914.25
80.0
1.0
16.0
Clay
201.87
3.05
289.63
9.14
438.84
30.48
631.93
91.43
631.93
457.13
631.93
914.25
80.0
1.0
17.0
Clay
201.87
3.05
289.63
9.14
438.84
30.48
631.93
91.43
631.93
457.13
631.93
914.25
80.0
1.0
18.0
Clay
201.87
3.05
289.63
9.14
438.84
30.48
631.93
91.43
631.93
457.13
631.93
914.25
80.0
1.0
19.0
Clay
201.87
3.05
289.63
9.14
438.84
30.48
631.93
91.43
631.93
457.13
631.93
914.25
80.0
1.0
19.0
Clay
315.42
1.52
452.55
4.57
685.69
15.24
685.69
45.71
685.69
228.56
685.69
457.13
125.0
0.5
20.0
Clay
315.42
1.52
452.55
4.57
685.69
15.24
685.69
45.71
685.69
228.56
685.69
457.13
125.0
0.5
21.0
Clay
315.42
1.52
452.55
4.57
685.69
15.24
685.69
45.71
685.69
228.56
685.69
457.13
125.0
0.5
22.0
Clay
315.42
1.52
452.55
4.57
685.69
15.24
685.69
45.71
685.69
228.56
685.69
457.13
125.0
0.5
23.0
Clay
315.42
1.52
452.55
4.57
685.69
15.24
685.69
45.71
685.69
228.56
685.69
457.13
125.0
0.5
23.0
Clay
504.67
1.52
724.09
4.57
1097.10
15.24
1097.10
45.71
1097.10
228.56
1097.10
457.13
200.0
0.5
24.0
Clay
504.67
1.52
724.09
4.57
1097.10
15.24
1097.10
45.71
1097.10
228.56
1097.10
457.13
200.0
0.5
25.0
Clay
504.67
1.52
724.09
4.57
1097.10
15.24
1097.10
45.71
1097.10
228.56
1097.10
457.13
200.0
0.5
26.0
Clay
504.67
1.52
724.09
4.57
1097.10
15.24
1097.10
45.71
1097.10
228.56
1097.10
457.13
200.0
0.5
27.0
Clay
504.67
1.52
724.09
4.57
1097.10
15.24
1097.10
45.71
1097.10
228.56
1097.10
457.13
200.0
0.5
27.0
Clay
605.60
1.52
868.90
4.57
1316.52
15.24
1316.52
45.71
1316.52
228.56
1316.52
457.13
240.0
0.5
25o
0.5
25o
0.5
Date Performed
10/06/2013
Made by
SP
Plate 17g
1219 mm
(kN/m)
(mm)
50/deg
P1
Y1
P2
Y2
P3
Y3
P4
Y4
P5
Y5
P6
Y6
Su
240.0
30.0
Clay
605.60
1.52
868.90
4.57
1316.52
15.24
1316.52
45.71
1316.52
228.56
1316.52
457.13
30.0
Silt
312.01
2.54
621.88
5.08
1226.97
10.16
2329.88
20.32
3909.18
40.63
4172.30
45.71
25o
0.5
33.0
Silt
343.21
2.54
684.07
5.08
1349.67
10.16
2562.87
20.32
4300.10
40.63
4589.53
45.71
25o
33.0
Clay
302.80
1.52
434.45
4.57
658.26
15.24
658.26
45.71
658.26
228.56
658.26
457.13
120.0
38.0
Clay
302.80
1.52
434.45
4.57
658.26
15.24
658.26
45.71
658.26
228.56
658.26
457.13
120.0
38.0
Silt
395.23
2.54
787.83
5.08
1555.07
10.16
2957.58
20.32
4985.01
40.63
5326.61
45.71
41.0
Silt
426.44
2.54
850.09
5.08
1678.29
10.16
3194.30
20.32
5395.54
40.63
5768.38
45.71
41.0
Clay
302.80
1.52
434.45
4.57
658.26
15.24
658.26
45.71
658.26
228.56
658.26
457.13
120.0
45.0
Clay
302.80
1.52
434.45
4.57
658.26
15.24
658.26
45.71
658.26
228.56
658.26
457.13
120.0
45.0
Silt
1106.49
2.54
2200.86
5.08
4307.83
10.16
7951.74
20.32
12381.21
40.63
12989.55
45.71
30o
51.7
Silt
1271.20
2.54
2528.26
5.08
4947.10
10.16
9121.76
20.32
14165.28
40.63
14852.98
45.71
30o
51.7
Clay
353.27
1.52
506.86
4.57
767.97
15.24
767.97
45.71
767.97
228.56
767.97
457.13
140.0
0.5
58.0
Clay
353.27
1.52
506.86
4.57
767.97
15.24
767.97
45.71
767.97
228.56
767.97
457.13
140.0
0.5
58.0
Clay
353.27
1.52
506.86
4.57
767.97
15.24
767.97
45.71
767.97
228.56
767.97
457.13
140.0
0.5
65.6
Clay
353.27
1.52
506.86
4.57
767.97
15.24
767.97
45.71
767.97
228.56
767.97
457.13
140.0
65.6
Sand
682.26
2.54
1359.86
5.08
2683.12
10.16
5095.68
20.32
8553.29
40.63
9129.92
45.71
25o
67.0
Sand
696.82
2.54
1388.87
5.08
2740.30
10.16
5203.84
20.32
8732.80
40.63
9320.99
45.71
25o
67 0
67.0
Silt
1647 32
1647.32
2 54
2.54
3275 90
3275.90
5 08
5.08
6406 82
6406.82
10 16
10.16
11792 91
11792.91
20 32
20.32
18237 58
18237.58
40 63
40.63
19106 46
19106.46
45 71
45.71
30o
73.0
Silt
1794.80
2.54
3568.91
5.08
6977.90
10.16
12831.61
20.32
19797.89
40.63
20731.15
45.71
30o
73.0
Silt
908.40
1.52
1303.35
4.57
1974.78
15.24
1974.78
45.71
1974.78
228.56
1974.78
457.13
360.0
0.5
74.3
Silt
908.40
1.52
1303.35
4.57
1974.78
15.24
1974.78
45.71
1974.78
228.56
1974.78
457.13
360.0
0.5
74.3
Clay
504.67
1.52
724.09
4.57
1097.10
15.24
1097.10
45.71
1097.10
228.56
1097.10
457.13
200.0
0.5
76.3
Clay
504.67
1.52
724.09
4.57
1097.10
15.24
1097.10
45.71
1097.10
228.56
1097.10
457.13
200.0
76.3
Silt
1875.92
2.54
3730.15
5.08
7292.63
10.16
13407.01
20.32
20673.42
40.63
21645.30
45.71
30o
78.4
Silt
1927.55
2.54
3832.79
5.08
7493.17
10.16
13774.92
20.32
21237.84
40.63
22235.63
45.71
30o
78.4
Clay
555.13
1.52
796.49
4.57
1206.81
15.24
1206.81
45.71
1206.81
228.56
1206.81
457.13
220.0
79.2
Clay
555.13
1.52
796.49
4.57
1206.81
15.24
1206.81
45.71
1206.81
228.56
1206.81
457.13
220.0
79.2
Silt
1947.22
2.54
3871.94
5.08
7569.89
10.16
13917.17
20.32
21461.60
40.63
22470.86
45.71
30o
81.0
Silt
1991.47
2.54
3959.88
5.08
7741.51
10.16
14230.68
20.32
21937.73
40.63
22967.80
45.71
30o
81.0
Sand
1991.47
2.54
3959.88
5.08
7741.51
10.16
14230.68
20.32
21937.73
40.63
22967.80
45.71
30o
86.0
Sand
2114.05
2.54
4201.51
5.08
8198.16
10.16
14971.89
20.32
22731.00
40.63
23725.05
45.71
30o
86.0
Silt
2114.05
2.54
4201.51
5.08
8198.16
10.16
14971.89
20.32
22731.00
40.63
23725.05
45.71
30o
88.6
Silt
2177.97
2.54
4328.60
5.08
8446.50
10.16
15427.68
20.32
23430.82
40.63
24457.09
45.71
30o
88.6
Clay
504.67
1.52
724.09
4.57
1097.10
15.24
1097.10
45.71
1097.10
228.56
1097.10
457.13
200.0
90.8
Clay
504.67
1.52
724.09
4.57
1097.10
15.24
1097.10
45.71
1097.10
228.56
1097.10
457.13
200.0
90.8
Silt
2232.05
2.54
4436.13
5.08
8656.64
10.16
15813.33
20.32
24022.96
40.63
25076.50
45.71
30o
93.0
Silt
2286.12
2.54
4543.50
5.08
8865.53
10.16
16191.02
20.32
24583.14
40.63
25658.43
45.71
30o
93.0
Clay
403.73
1.52
579.27
4.57
877.68
15.24
877.68
45.71
877.68
228.56
877.68
457.13
160.0
0.5
97.0
Clay
605.60
1.52
868.90
4.57
1316.52
15.24
1316.52
45.71
1316.52
228.56
1316.52
457.13
240.0
0.5
97.0
Clay
403.73
1.52
579.27
4.57
877.68
15.24
877.68
45.71
877.68
228.56
877.68
457.13
160.0
0.5
102.5
Clay
267.47
1.52
383.77
4.57
581.46
15.24
581.46
45.71
581.46
228.56
581.46
457.13
106.0
0.5
0.5
0.5
25o
25o
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
Date Performed
10/06/2013
Made by
SP
Plate 17h
1219 mm
(mm)
P1
Y1
P2
Y2
P3
Y3
P4
Y4
P5
Y5
P6
Y6
Su
50/deg
102.5
Silt
1065.91
2.54
2123.74
5.08
4184.30
10.16
7905.35
20.32
13075.64
40.63
13906.81
45.71
25o
103.4
Silt
1075.26
2.54
2142.38
5.08
4221.04
10.16
7974.76
20.32
13190.45
40.63
14028.92
45.71
25o
103.4
Clay
403.73
1.52
579.27
4.57
877.68
15.24
877.68
45.71
877.68
228.56
877.68
457.13
160.0
106.0
Clay
403.73
1.52
579.27
4.57
877.68
15.24
877.68
45.71
877.68
228.56
877.68
457.13
160.0
0.5
106.0
Clay
605.60
1.52
868.90
4.57
1316.52
15.24
1316.52
45.71
1316.52
228.56
1316.52
457.13
240.0
0.5
240.0
0.5
107.3
Clay
605.60
1.52
868.90
4.57
1316.52
15.24
1316.52
45.71
1316.52
228.56
1316.52
457.13
107.3
Sand
2637.66
2.54
5242.25
5.08
10229.61
10.16
18686.33
20.32
28386.09
40.63
29630.68
45.71
30o
0.5
109.0
Sand
2679.45
2.54
5325.36
5.08
10392.10
10.16
18985.02
20.32
28846.39
40.63
30112.52
45.71
30o
109.0
Clay
504.67
1.52
724.09
4.57
1097.10
15.24
1097.10
45.71
1097.10
228.56
1097.10
457.13
200.0
116.3
Clay
504.67
1.52
724.09
4.57
1097.10
15.24
1097.10
45.71
1097.10
228.56
1097.10
457.13
200.0
116.3
Sand
2858.92
2.54
5682.18
5.08
11089.35
10.16
20264.67
20.32
30811.14
40.63
32167.76
45.71
30o
123.0
Sand
3023.64
2.54
6009.67
5.08
11729.30
10.16
21439.11
20.32
32614.34
40.63
34054.01
45.71
30o
123.0
Clay
504.67
1.52
724.09
4.57
1097.10
15.24
1097.10
45.71
1097.10
228.56
1097.10
457.13
200.0
125.0
Clay
504.67
1.52
724.09
4.57
1097.10
15.24
1097.10
45.71
1097.10
228.56
1097.10
457.13
200.0
125.0
Sand
3072.81
2.54
6107.43
5.08
11920.32
10.16
21789.69
20.32
33152.60
40.63
34617.05
45.71
134.0
Sand
3294.08
2.54
6547.34
5.08
12779.94
10.16
23367.25
20.32
35574.71
40.63
37150.71
45.71
134.0
Clay
908.40
1.52
1303.35
4.57
1974.78
15.24
1974.78
45.71
1974.78
228.56
1974.78
457.13
360.0
139 0
139.0
Clay
908 40
908.40
1 52
1.52
1303 35
1303.35
4 57
4.57
1974 78
1974.78
15 24
15.24
1974 78
1974.78
45 71
45.71
1974 78
1974.78
228 56
228.56
1974 78
1974.78
457 13
457.13
360 0
360.0
05
0.5
139.0
Clay
555.13
1.52
796.49
4.57
1206.81
15.24
1206.81
45.71
1206.81
228.56
1206.81
457.13
220.0
0.5
140.0
Clay
555.13
1.52
796.49
4.57
1206.81
15.24
1206.81
45.71
1206.81
228.56
1206.81
457.13
220.0
0.5
0.5
0.5
0.5
0.5
30o
30o
0.5
Date Performed
10/06/2013
Made by
SP
Plate 17i
DEPTH
(m)
Soil
type
T1
Z1
T2
Z2
T3
T4
T5
Z3
Z4
Z5
* T (kN/m) Z (mm) *
T6
Z6
T7
Z7
0.0
Sand
3.1
Sand
3.1
Clay
42
4.2
Cl
Clay
4.2
Sand
5.2
Sand
5.2
Clay
7.5
Clay
7.5
Silt
10.0
Silt
10.0
Clay
15.0
Clay
15.0
Clay
19.0
Clay
19.0
Clay
23.0
Clay
23.0
Clay
27.0
Clay
27.0
Clay
30.0
Clay
30.0
Silt
33.0
Silt
0.00
2.54
20.53
2.54
88.18
2.54
96 23
96.23
2.54
29.12
2.54
36.64
2.54
51.42
1.22
56.18
1.22
52.19
2.54
68.58
2.54
60.14
1.22
66.54
1.22
38.99
1.22
43.98
1.22
54.97
1 22
1.22
61.14
1.22
77.33
1.22
83.92
1.22
91.93
1 22
1.22
97.04
1.22
160.39
2.54
160.39
2.54
0.00
5.08
20.53
5.08
88.18
5.08
96.23
96 23
5.08
29.12
5.08
36.64
5.08
85.70
2.36
93.63
2.36
52.19
5.08
68.58
5.08
100.24
2.36
110.90
2.36
64.98
2.36
73.30
2.36
91.62
2 36
2.36
101.89
2.36
128.89
2.36
139.87
2.36
153.22
2.36
2 36
161.73
2.36
160.39
5.08
160.39
5.08
0.00
12.70
20.53
12.70
88.18
12.70
96.23
96 23
12.70
29.12
12.70
36.64
12.70
128.56
4.34
140.44
4.34
52.19
12.70
68.58
12.70
150.36
4.34
166.35
4.34
97.48
4.34
109.95
4.34
137.43
4 34
4.34
152.84
4.34
193.33
4.34
209.80
4.34
229.83
4.34
4 34
242.60
4.34
160.39
12.70
160.39
12.70
0.00
127.00
20.53
127.00
88.18
127.00
96.23
96 23
127.00
29.12
127.00
36.64
127.00
154.27
15.24
168.53
15.24
52.19
127.00
68.58
127.00
180.43
15.24
199.62
15.24
116.97
15.24
131.94
15.24
164.92
15 24
15.24
183.41
15.24
232.00
15.24
251.76
15.24
275.79
15.24
15 24
291.12
15.24
160.39
127.00
160.39
127.00
0.00
254.00
20.53
254.00
88.18
254.00
96.23
96 23
254.00
29.12
254.00
36.64
254.00
154.27
38.10
168.53
38.10
52.19
254.00
68.58
254.00
180.43
38.10
199.62
38.10
116.97
38.10
131.94
38.10
164.92
38 10
38.10
183.41
38.10
232.00
38.10
251.76
38.10
275.79
38.10
38 10
291.12
38.10
160.39
254.00
160.39
254.00
0.00
25.40
20.53
25.40
88.18
25.40
96.23
96 23
25.40
29.12
25.40
36.64
25.40
154.27
6.10
168.53
6.10
52.19
25.40
68.58
25.40
180.43
6.10
199.62
6.10
116.97
6.10
131.94
6.10
164.92
6 10
6.10
183.41
6.10
232.00
6.10
251.76
6.10
275.79
6.10
6 10
291.12
6.10
160.39
25.40
160.39
25.40
0.00
50.80
20.53
50.80
88.18
50.80
96.23
96 23
50.80
29.12
50.80
36.64
50.80
171.41
7.62
187.26
7.62
52.19
50.80
68.58
50.80
200.48
7.62
221.80
7.62
129.97
7.62
146.60
7.62
183.24
7 62
7.62
203.79
7.62
257.77
7.62
279.74
7.62
306.44
7.62
7 62
323.47
7.62
160.39
50.80
160.39
50.80
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 18a
DEPTH
(m)
Soil
type
T1
Z1
T2
Z2
T3
T4
T5
Z3
Z4
Z5
* T (kN/m) Z (mm) *
T6
Z6
T7
Z7
33.0
Clay
38.0
Clay
38.0
Silt
41 0
41.0
Silt
41.0
Clay
45.0
Clay
45.0
Silt
51.7
Silt
51.7
Clay
58.0
Clay
58.0
Clay
65.6
Clay
65.6
Sand
67.0
Sand
67.0
Silt
73.0
Silt
73.0
Silt
74.3
Silt
74.3
Clay
76.3
Clay
76.3
Silt
78.4
Silt
72.02
1.22
77.35
1.22
48.12
1.22
48.12
48
12
1.22
80.76
1.22
85.09
1.22
194.62
2.54
194.62
2.54
98.27
1.22
100.54
1.22
100.54
1.22
100.54
1.22
160.39
2.54
160.39
2.54
194.62
2 54
2.54
194.62
2.54
186.07
1.22
187.60
1.22
139.83
1 22
1.22
141.57
1.22
194.62
2.54
194.62
2.54
120.03
2.36
128.92
2.36
80.20
2.36
80.20
80 20
2.36
134.60
2.36
141.81
2.36
194.62
5.08
194.62
5.08
163.78
2.36
167.57
2.36
167.57
2.36
167.57
2.36
160.39
5.08
160.39
5.08
194.62
5 08
5.08
194.62
5.08
310.11
2.36
312.67
2.36
233.05
2.36
2 36
235.95
2.36
194.62
5.08
194.62
5.08
180.04
4.34
193.38
4.34
120.29
4.34
120.29
120 29
4.34
201.89
4.34
212.72
4.34
194.62
12.70
194.62
12.70
245.68
4.34
251.36
4.34
251.36
4.34
251.36
4.34
160.39
12.70
160.39
12.70
194.62
12 70
12.70
194.62
12.70
465.17
4.34
469.00
4.34
349.57
4.34
4 34
353.93
4.34
194.62
12.70
194.62
12.70
216.05
15.24
232.06
15.24
144.35
15.24
144.35
144 35
15.24
242.27
15.24
255.26
15.24
194.62
127.00
194.62
127.00
294.81
15.24
301.63
15.24
301.63
15.24
301.63
15.24
160.39
127.00
160.39
127.00
194.62
127 00
127.00
194.62
127.00
558.20
15.24
562.80
15.24
419.49
15.24
15 24
424.71
15.24
194.62
127.00
194.62
127.00
216.05
38.10
232.06
38.10
144.35
38.10
144.35
144 35
38.10
242.27
38.10
255.26
38.10
194.62
254.00
194.62
254.00
294.81
38.10
301.63
38.10
301.63
38.10
301.63
38.10
160.39
254.00
160.39
254.00
194.62
254 00
254.00
194.62
254.00
558.20
38.10
562.80
38.10
419.49
38.10
38 10
424.71
38.10
194.62
254.00
194.62
254.00
216.05
6.10
232.06
6.10
144.35
6.10
144.35
144 35
6.10
242.27
6.10
255.26
6.10
194.62
25.40
194.62
25.40
294.81
6.10
301.63
6.10
301.63
6.10
301.63
6.10
160.39
25.40
160.39
25.40
194.62
25 40
25.40
194.62
25.40
558.20
6.10
562.80
6.10
419.49
6.10
6 10
424.71
6.10
194.62
25.40
194.62
25.40
240.06
7.62
257.84
7.62
160.39
7.62
160.39
160 39
7.62
269.19
7.62
283.62
7.62
194.62
50.80
194.62
50.80
327.57
7.62
335.15
7.62
335.15
7.62
335.15
7.62
160.39
50.80
160.39
50.80
194.62
50 80
50.80
194.62
50.80
620.22
7.62
625.34
7.62
466.10
7.62
7 62
471.90
7.62
194.62
50.80
194.62
50.80
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 18b
DEPTH
(m)
Soil
type
T1
Z1
T2
Z2
T3
T4
T5
Z3
Z4
Z5
* T (kN/m) Z (mm) *
T6
Z6
T7
Z7
78.4
Clay
79.2
Clay
79.2
Silt
81 0
81.0
Silt
81.0
Sand
86.0
Sand
86.0
Silt
88.6
Silt
88.6
Clay
90.8
Clay
90.8
Silt
93.0
Silt
93.0
Clay
97.0
Clay
97.0
Clay
102.5
Clay
102.5
Silt
103.4
Silt
103.4
Clay
106.0
Clay
106.0
Clay
107.3
Clay
150.49
1.22
151.25
1.22
58.39
1.22
58.39
58
39
1.22
194.62
2.54
194.62
2.54
194.62
2.54
194.62
2.54
143.63
1.22
143.63
1.22
194.62
2.54
194.62
2.54
114.91
1.22
172.36
1.22
114.91
1 22
1.22
114.91
1.22
160.39
2.54
160.39
2.54
114.91
1 22
1.22
114.91
1.22
172.36
1.22
172.36
1.22
250.82
2.36
252.08
2.36
97.31
2.36
97.31
97 31
2.36
194.62
5.08
194.62
5.08
194.62
5.08
194.62
5.08
239.39
2.36
239.39
2.36
194.62
5.08
194.62
5.08
191.51
2.36
287.27
2.36
191.51
2 36
2.36
191.51
2.36
160.39
5.08
160.39
5.08
191.51
2.36
2 36
191.51
2.36
287.27
2.36
287.27
2.36
376.22
4.34
378.12
4.34
145.97
4.34
145.97
145 97
4.34
194.62
12.70
194.62
12.70
194.62
12.70
194.62
12.70
359.08
4.34
359.08
4.34
194.62
12.70
194.62
12.70
287.27
4.34
430.90
4.34
287.27
4 34
4.34
287.27
4.34
160.39
12.70
160.39
12.70
287.27
4.34
4 34
287.27
4.34
430.90
4.34
430.90
4.34
451.47
15.24
453.74
15.24
175.16
15.24
175.16
175 16
15.24
194.62
127.00
194.62
127.00
194.62
127.00
194.62
127.00
430.90
15.24
430.90
15.24
194.62
127.00
194.62
127.00
344.72
15.24
517.08
15.24
344.72
15 24
15.24
344.72
15.24
160.39
127.00
160.39
127.00
344.72
15.24
15 24
344.72
15.24
517.08
15.24
517.08
15.24
451.47
38.10
453.74
38.10
175.16
38.10
175.16
175 16
38.10
194.62
254.00
194.62
254.00
194.62
254.00
194.62
254.00
430.90
38.10
430.90
38.10
194.62
254.00
194.62
254.00
344.72
38.10
517.08
38.10
344.72
38 10
38.10
344.72
38.10
160.39
254.00
160.39
254.00
344.72
38.10
38 10
344.72
38.10
517.08
38.10
517.08
38.10
451.47
6.10
453.74
6.10
175.16
6.10
175.16
175 16
6.10
194.62
25.40
194.62
25.40
194.62
25.40
194.62
25.40
430.90
6.10
430.90
6.10
194.62
25.40
194.62
25.40
344.72
6.10
517.08
6.10
344.72
6 10
6.10
344.72
6.10
160.39
25.40
160.39
25.40
344.72
6.10
6 10
344.72
6.10
517.08
6.10
517.08
6.10
501.63
7.62
504.16
7.62
194.62
7.62
194.62
194 62
7.62
194.62
50.80
194.62
50.80
194.62
50.80
194.62
50.80
478.78
7.62
478.78
7.62
194.62
50.80
194.62
50.80
383.02
7.62
574.53
7.62
383.02
7 62
7.62
383.02
7.62
160.39
50.80
160.39
50.80
383.02
7.62
7 62
383.02
7.62
574.53
7.62
574.53
7.62
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 18c
DEPTH
(m)
Soil
type
T1
Z1
T2
Z2
T3
T4
T5
Z3
Z4
Z5
* T (kN/m) Z (mm) *
T6
Z6
T7
Z7
107.3
Sand
109.0
Sand
109.0
Clay
116 3
116.3
Clay
Cl
116.3
Sand
123.0
Sand
123.0
Clay
125.0
Clay
125.0
Sand
134.0
Sand
134.0
Clay
139.0
Clay
139.0
Clay
140.0
Clay
194.62
2.54
194.62
2.54
478.78
2.54
478 78
478.78
2.54
194.62
2.54
194.62
2.54
143.63
1.22
143.63
1.22
194.62
2.54
194.62
2.54
835.65
2.54
851.69
2.54
158.00
1.22
158.00
1.22
194.62
5.08
194.62
5.08
478.78
5.08
478.78
478 78
5.08
194.62
5.08
194.62
5.08
239.39
2.36
239.39
2.36
194.62
5.08
194.62
5.08
835.65
5.08
851.69
5.08
263.33
2.36
263.33
2.36
194.62
12.70
194.62
12.70
478.78
12.70
478.78
478 78
12.70
194.62
12.70
194.62
12.70
359.08
4.34
359.08
4.34
194.62
12.70
194.62
12.70
835.65
12.70
851.69
12.70
394.99
4.34
394.99
4.34
194.62
127.00
194.62
127.00
478.78
127.00
478.78
478 78
127.00
194.62
127.00
194.62
127.00
430.90
15.24
430.90
15.24
194.62
127.00
194.62
127.00
835.65
127.00
851.69
127.00
473.99
15.24
473.99
15.24
194.62
254.00
194.62
254.00
478.78
254.00
478.78
478 78
254.00
194.62
254.00
194.62
254.00
430.90
38.10
430.90
38.10
194.62
254.00
194.62
254.00
835.65
254.00
851.69
254.00
473.99
38.10
473.99
38.10
194.62
25.40
194.62
25.40
478.78
25.40
478.78
478 78
25.40
194.62
25.40
194.62
25.40
430.90
6.10
430.90
6.10
194.62
25.40
194.62
25.40
835.65
25.40
851.69
25.40
473.99
6.10
473.99
6.10
194.62
50.80
194.62
50.80
478.78
50.80
478.78
478 78
50.80
194.62
50.80
194.62
50.80
478.78
7.62
478.78
7.62
194.62
50.80
194.62
50.80
835.65
50.80
851.69
50.80
526.66
7.62
526.66
7.62
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 18d
DEPTH
(m)
Soil
type
T1
Z1
T2
Z2
T3
T4
T5
Z3
Z4
Z5
* T (kN/m) Z (mm) *
T6
Z6
T7
Z7
0.0
Sand
3.1
Sand
3.1
Clay
42
4.2
Cl
Clay
4.2
Sand
5.2
Sand
5.2
Clay
7.5
Clay
7.5
Silt
10.0
Silt
10.0
Clay
15.0
Clay
15.0
Clay
19.0
Clay
19.0
Clay
23.0
Clay
23.0
Clay
27.0
Clay
27.0
Clay
30.0
Clay
30.0
Silt
33.0
Silt
0.00
2.54
24.62
2.54
105.76
2.54
115 42
115.42
2.54
34.92
2.54
43.95
2.54
61.68
1.46
67.38
1.46
62.61
2.54
82.25
2.54
72.14
1.46
79.81
1.46
46.77
1.46
52.75
1.46
65.94
1 46
1.46
73.33
1.46
92.76
1.46
100.66
1.46
110.27
1 46
1.46
116.40
1.46
192.38
2.54
192.38
2.54
0.00
5.08
24.62
5.08
105.76
5.08
115.42
115 42
5.08
34.92
5.08
43.95
5.08
102.80
2.83
112.31
2.83
62.61
5.08
82.25
5.08
120.24
2.83
133.02
2.83
77.95
2.83
87.92
2.83
109.90
2 83
2.83
122.22
2.83
154.60
2.83
167.77
2.83
183.78
2.83
2 83
194.00
2.83
192.38
5.08
192.38
5.08
0.00
12.70
24.62
12.70
105.76
12.70
115.42
115 42
12.70
34.92
12.70
43.95
12.70
154.20
5.21
168.46
5.21
62.61
12.70
82.25
12.70
180.35
5.21
199.53
5.21
116.92
5.21
131.88
5.21
164.85
5 21
5.21
183.33
5.21
231.90
5.21
251.65
5.21
275.67
5.21
5 21
290.99
5.21
192.38
12.70
192.38
12.70
0.00
127.00
24.62
127.00
105.76
127.00
115.42
115 42
127.00
34.92
127.00
43.95
127.00
185.04
18.28
202.15
18.28
62.61
127.00
82.25
127.00
216.43
18.28
239.44
18.28
140.30
18.28
158.25
18.28
197.82
18 28
18.28
220.00
18.28
278.27
18.28
301.98
18.28
330.81
18.28
18 28
349.19
18.28
192.38
127.00
192.38
127.00
0.00
254.00
24.62
254.00
105.76
254.00
115.42
115 42
254.00
34.92
254.00
43.95
254.00
185.04
45.70
202.15
45.70
62.61
254.00
82.25
254.00
216.43
45.70
239.44
45.70
140.30
45.70
158.25
45.70
197.82
45 70
45.70
220.00
45.70
278.27
45.70
301.98
45.70
330.81
45.70
45 70
349.19
45.70
192.38
254.00
192.38
254.00
0.00
25.40
24.62
25.40
105.76
25.40
115.42
115 42
25.40
34.92
25.40
43.95
25.40
185.04
7.31
202.15
7.31
62.61
25.40
82.25
25.40
216.43
7.31
239.44
7.31
140.30
7.31
158.25
7.31
197.82
7 31
7.31
220.00
7.31
278.27
7.31
301.98
7.31
330.81
7.31
7 31
349.19
7.31
192.38
25.40
192.38
25.40
0.00
50.80
24.62
50.80
105.76
50.80
115.42
115 42
50.80
34.92
50.80
43.95
50.80
205.60
9.14
224.61
9.14
62.61
50.80
82.25
50.80
240.47
9.14
266.04
9.14
155.89
9.14
175.84
9.14
219.80
9 14
9.14
244.44
9.14
309.19
9.14
335.54
9.14
367.56
9.14
9 14
387.99
9.14
192.38
50.80
192.38
50.80
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 18e
DEPTH
(m)
Soil
type
T1
Z1
T2
Z2
T3
T4
T5
Z3
Z4
Z5
* T (kN/m) Z (mm) *
T6
Z6
T7
Z7
33.0
Clay
38.0
Clay
38.0
Silt
41 0
41.0
Silt
41.0
Clay
45.0
Clay
45.0
Silt
51.7
Silt
51.7
Clay
58.0
Clay
58.0
Clay
65.6
Clay
65.6
Sand
67.0
Sand
67.0
Silt
73.0
Silt
73.0
Silt
74.3
Silt
74.3
Clay
76.3
Clay
76.3
Silt
78.4
Silt
86.38
1.46
92.78
1.46
57.72
1.46
57.72
57
72
1.46
96.87
1.46
102.06
1.46
233.45
2.54
233.45
2.54
117.87
1.46
120.60
1.46
120.60
1.46
120.60
1.46
192.38
2.54
192.38
2.54
233.45
2 54
2.54
233.45
2.54
223.18
1.46
225.02
1.46
167.72
1 46
1.46
169.81
1.46
70.03
1.46
70.03
1.46
143.97
2.83
154.64
2.83
96.19
2.83
96.19
96 19
2.83
161.45
2.83
170.10
2.83
233.45
5.08
233.45
5.08
196.46
2.83
201.00
2.83
201.00
2.83
201.00
2.83
192.38
5.08
192.38
5.08
233.45
5 08
5.08
233.45
5.08
371.97
2.83
375.04
2.83
279.54
2.83
2 83
283.02
2.83
116.72
2.83
116.72
2.83
215.96
5.21
231.96
5.21
144.29
5.21
144.29
144 29
5.21
242.17
5.21
255.15
5.21
233.45
12.70
233.45
12.70
294.68
5.21
301.50
5.21
301.50
5.21
301.50
5.21
192.38
12.70
192.38
12.70
233.45
12 70
12.70
233.45
12.70
557.96
5.21
562.56
5.21
419.31
5.21
5 21
424.53
5.21
175.08
5.21
175.08
5.21
259.15
18.28
278.35
18.28
173.15
18.28
173.15
173 15
18.28
290.60
18.28
306.18
18.28
233.45
127.00
233.45
127.00
353.62
18.28
361.80
18.28
361.80
18.28
361.80
18.28
192.38
127.00
192.38
127.00
233.45
127 00
127.00
233.45
127.00
669.55
18.28
675.07
18.28
503.17
18.28
18 28
509.43
18.28
210.10
18.28
210.10
18.28
259.15
45.70
278.35
45.70
173.15
45.70
173.15
173 15
45.70
290.60
45.70
306.18
45.70
233.45
254.00
233.45
254.00
353.62
45.70
361.80
45.70
361.80
45.70
361.80
45.70
192.38
254.00
192.38
254.00
233.45
254 00
254.00
233.45
254.00
669.55
45.70
675.07
45.70
503.17
45.70
45 70
509.43
45.70
210.10
45.70
210.10
45.70
259.15
7.31
278.35
7.31
173.15
7.31
173.15
173 15
7.31
290.60
7.31
306.18
7.31
233.45
25.40
233.45
25.40
353.62
7.31
361.80
7.31
361.80
7.31
361.80
7.31
192.38
25.40
192.38
25.40
233.45
25 40
25.40
233.45
25.40
669.55
7.31
675.07
7.31
503.17
7.31
7 31
509.43
7.31
210.10
7.31
210.10
7.31
287.94
9.14
309.27
9.14
192.38
9.14
192.38
192 38
9.14
322.89
9.14
340.20
9.14
233.45
50.80
233.45
50.80
392.91
9.14
402.00
9.14
402.00
9.14
402.00
9.14
192.38
50.80
192.38
50.80
233.45
50 80
50.80
233.45
50.80
743.94
9.14
750.08
9.14
559.07
9.14
9 14
566.04
9.14
233.45
9.14
233.45
9.14
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 18f
DEPTH
(m)
Soil
type
T1
Z1
T2
Z2
T3
T4
T5
Z3
Z4
Z5
* T (kN/m) Z (mm) *
T6
Z6
T7
Z7
78.4
Clay
79.2
Clay
79.2
Silt
81 0
81.0
Silt
81.0
Sand
86.0
Sand
86.0
Silt
88.6
Silt
88.6
Clay
90.8
Clay
90.8
Silt
93.0
Silt
93.0
Clay
97.0
Clay
97.0
Clay
102.5
Clay
102.5
Silt
103.4
Silt
103.4
Clay
106.0
Clay
106.0
Clay
107.3
Clay
180.51
1.46
181.42
1.46
70.03
1.46
70.03
70
03
1.46
233.45
2.54
233.45
2.54
233.45
2.54
233.45
2.54
172.28
1.46
172.28
1.46
233.45
2.54
233.45
2.54
137.83
1.46
206.74
1.46
137.83
1 46
1.46
137.83
1.46
192.38
2.54
192.38
2.54
137.83
1 46
1.46
137.83
1.46
206.74
1.46
206.74
1.46
300.85
2.83
302.36
2.83
116.72
2.83
116.72
116 72
2.83
233.45
5.08
233.45
5.08
233.45
5.08
233.45
5.08
287.14
2.83
287.14
2.83
233.45
5.08
233.45
5.08
229.71
2.83
344.57
2.83
229.71
2 83
2.83
229.71
2.83
192.38
5.08
192.38
5.08
229.71
2.83
2 83
229.71
2.83
344.57
2.83
344.57
2.83
451.27
5.21
453.54
5.21
175.08
5.21
175.08
175 08
5.21
233.45
12.70
233.45
12.70
233.45
12.70
233.45
12.70
430.71
5.21
430.71
5.21
233.45
12.70
233.45
12.70
344.57
5.21
516.85
5.21
344.57
5 21
5.21
344.57
5.21
192.38
12.70
192.38
12.70
344.57
5.21
5 21
344.57
5.21
516.85
5.21
516.85
5.21
541.52
18.28
544.25
18.28
210.10
18.28
210.10
210 10
18.28
233.45
127.00
233.45
127.00
233.45
127.00
233.45
127.00
516.85
18.28
516.85
18.28
233.45
127.00
233.45
127.00
413.48
18.28
620.23
18.28
413.48
18 28
18.28
413.48
18.28
192.38
127.00
192.38
127.00
413.48
18.28
18 28
413.48
18.28
620.23
18.28
620.23
18.28
541.52
45.70
544.25
45.70
210.10
45.70
210.10
210 10
45.70
233.45
254.00
233.45
254.00
233.45
254.00
233.45
254.00
516.85
45.70
516.85
45.70
233.45
254.00
233.45
254.00
413.48
45.70
620.23
45.70
413.48
45 70
45.70
413.48
45.70
192.38
254.00
192.38
254.00
413.48
45.70
45 70
413.48
45.70
620.23
45.70
620.23
45.70
541.52
7.31
544.25
7.31
210.10
7.31
210.10
210 10
7.31
233.45
25.40
233.45
25.40
233.45
25.40
233.45
25.40
516.85
7.31
516.85
7.31
233.45
25.40
233.45
25.40
413.48
7.31
620.23
7.31
413.48
7 31
7.31
413.48
7.31
192.38
25.40
192.38
25.40
413.48
7.31
7 31
413.48
7.31
620.23
7.31
620.23
7.31
601.69
9.14
604.72
9.14
233.45
9.14
233.45
233 45
9.14
233.45
50.80
233.45
50.80
233.45
50.80
233.45
50.80
574.28
9.14
574.28
9.14
233.45
50.80
233.45
50.80
459.43
9.14
689.14
9.14
459.43
9 14
9.14
459.43
9.14
192.38
50.80
192.38
50.80
459.43
9.14
9 14
459.43
9.14
689.14
9.14
689.14
9.14
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 18g
DEPTH
(m)
Soil
type
107.3
Sand
109.0
Sand
109.0
Clay
116 3
116.3
Clay
Cl
116.3
Sand
123.0
Sand
123.0
Clay
125.0
Clay
125.0
Sand
134.0
Sand
134.0
Clay
139.0
Clay
139.0
Clay
140.0
Clay
T1
Z1
233.45
2.54
233.45
2.54
574.28
2.54
574 28
574.28
2.54
233.45
2.54
233.45
2.54
172.28
1.46
172.28
1.46
233.45
2.54
233.45
2.54
1002.34
2.54
1021.59
2.54
189.51
1.46
189.51
1.46
T2
Z2
233.45
5.08
233.45
5.08
574.28
5.08
574.28
574 28
5.08
233.45
5.08
233.45
5.08
287.14
2.83
287.14
2.83
233.45
5.08
233.45
5.08
1002.34
5.08
1021.59
5.08
315.86
2.83
315.86
2.83
T3
T4
T5
Z3
Z4
Z5
* T (kN/m) Z (mm) *
233.45
12.70
233.45
12.70
574.28
12.70
574.28
574 28
12.70
233.45
12.70
233.45
12.70
430.71
5.21
430.71
5.21
233.45
12.70
233.45
12.70
1002.34
12.70
1021.59
12.70
473.78
5.21
473.78
5.21
233.45
25.40
233.45
25.40
574.28
25.40
574.28
574 28
25.40
233.45
25.40
233.45
25.40
516.85
7.31
516.85
7.31
233.45
25.40
233.45
25.40
1002.34
25.40
1021.59
25.40
568.54
7.31
568.54
7.31
233.45
50.80
233.45
50.80
574.28
50.80
574.28
574 28
50.80
233.45
50.80
233.45
50.80
574.28
9.14
574.28
9.14
233.45
50.80
233.45
50.80
1002.34
50.80
1021.59
50.80
631.71
9.14
631.71
9.14
T6
Z6
T7
Z7
233.45
127.00
233.45
127.00
574.28
127.00
574.28
574 28
127.00
233.45
127.00
233.45
127.00
516.85
18.28
516.85
18.28
233.45
127.00
233.45
127.00
1002.34
127.00
1021.59
127.00
568.54
18.28
568.54
18.28
233.45
254.00
233.45
254.00
574.28
254.00
574.28
574 28
254.00
233.45
254.00
233.45
254.00
516.85
45.70
516.85
45.70
233.45
254.00
233.45
254.00
1002.34
254.00
1021.59
254.00
568.54
45.70
568.54
45.70
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 18h
DEPTH
(m)
Soil
type
T1
Z1
T2
Z2
T3
T4
T5
Z3
Z4
Z5
* T (kN/m) Z (mm) *
T6
Z6
T7
Z7
0.0
Sand
3.1
Sand
3.1
Clay
42
4.2
Cl
Clay
4.2
Sand
5.2
Sand
5.2
Clay
7.5
Clay
7.5
Silt
10.0
Silt
10.0
Clay
15.0
Clay
15.0
Clay
19.0
Clay
19.0
Clay
23.0
Clay
23.0
Clay
27.0
Clay
27.0
Clay
30.0
Clay
30.0
Silt
33.0
Silt
0.00
2.54
32.84
2.54
141.06
2.54
153 94
153.94
2.54
46.58
2.54
58.62
2.54
82.26
1.95
89.87
1.95
83.50
2.54
109.70
2.54
96.22
1.95
106.45
1.95
62.37
1.95
70.35
1.95
87.94
1 95
1.95
97.80
1.95
123.71
1.95
134.25
1.95
147.07
1 95
1.95
155.24
1.95
256.58
2.54
256.58
2.54
0.00
5.08
32.84
5.08
141.06
5.08
153.94
153 94
5.08
46.58
5.08
58.62
5.08
137.10
3.78
149.78
3.78
83.50
5.08
109.70
5.08
160.36
3.78
177.41
3.78
103.96
3.78
117.26
3.78
146.57
3 78
3.78
163.00
3.78
206.19
3.78
223.75
3.78
245.11
3.78
3 78
258.73
3.78
256.58
5.08
256.58
5.08
0.00
12.70
32.84
12.70
141.06
12.70
153.94
153 94
12.70
46.58
12.70
58.62
12.70
205.66
6.95
224.67
6.95
83.50
12.70
109.70
12.70
240.54
6.95
266.11
6.95
155.94
6.95
175.89
6.95
219.86
6 95
6.95
244.51
6.95
309.28
6.95
335.63
6.95
367.66
6.95
6 95
388.10
6.95
256.58
12.70
256.58
12.70
0.00
127.00
32.84
127.00
141.06
127.00
153.94
153 94
127.00
46.58
127.00
58.62
127.00
246.79
24.38
269.61
24.38
83.50
127.00
109.70
127.00
288.65
24.38
319.34
24.38
187.12
24.38
211.06
24.38
263.83
24 38
24.38
293.41
24.38
371.13
24.38
402.76
24.38
441.20
24.38
24 38
465.72
24.38
256.58
127.00
256.58
127.00
0.00
254.00
32.84
254.00
141.06
254.00
153.94
153 94
254.00
46.58
254.00
58.62
254.00
246.79
60.95
269.61
60.95
83.50
254.00
109.70
254.00
288.65
60.95
319.34
60.95
187.12
60.95
211.06
60.95
263.83
60 95
60.95
293.41
60.95
371.13
60.95
402.76
60.95
441.20
60.95
60 95
465.72
60.95
256.58
254.00
256.58
254.00
0.00
25.40
32.84
25.40
141.06
25.40
153.94
153 94
25.40
46.58
25.40
58.62
25.40
246.79
9.75
269.61
9.75
83.50
25.40
109.70
25.40
288.65
9.75
319.34
9.75
187.12
9.75
211.06
9.75
263.83
9 75
9.75
293.41
9.75
371.13
9.75
402.76
9.75
441.20
9.75
9 75
465.72
9.75
256.58
25.40
256.58
25.40
0.00
50.80
32.84
50.80
141.06
50.80
153.94
153 94
50.80
46.58
50.80
58.62
50.80
274.21
12.19
299.56
12.19
83.50
50.80
109.70
50.80
320.72
12.19
354.82
12.19
207.92
12.19
234.51
12.19
293.14
12 19
12.19
326.01
12.19
412.37
12.19
447.51
12.19
490.22
12.19
12 19
517.46
12.19
256.58
50.80
256.58
50.80
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 18i
DEPTH
(m)
Soil
type
T1
Z1
T2
Z2
T3
T4
T5
Z3
Z4
Z5
* T (kN/m) Z (mm) *
T6
Z6
T7
Z7
33.0
Clay
38.0
Clay
38.0
Silt
41 0
41.0
Silt
41.0
Clay
45.0
Clay
45.0
Silt
51.7
Silt
51.7
Clay
58.0
Clay
58.0
Clay
65.6
Clay
65.6
Sand
67.0
Sand
67.0
Silt
73.0
Silt
73.0
Silt
74.3
Silt
74.3
Clay
76.3
Clay
76.3
Silt
78.4
Silt
115.21
1.95
123.74
1.95
76.97
1.95
76.97
76
97
1.95
129.19
1.95
136.12
1.95
311.35
2.54
311.35
2.54
157.21
1.95
160.84
1.95
160.84
1.95
160.84
1.95
256.58
2.54
256.58
2.54
311.35
2 54
2.54
311.35
2.54
297.66
1.95
300.11
1.95
223.69
1 95
1.95
226.48
1.95
93.40
1.95
93.40
1.95
192.02
3.78
206.24
3.78
128.29
3.78
128.29
128 29
3.78
215.32
3.78
226.86
3.78
311.35
5.08
311.35
5.08
262.01
3.78
268.07
3.78
268.07
3.78
268.07
3.78
256.58
5.08
256.58
5.08
311.35
5 08
5.08
311.35
5.08
496.10
3.78
500.19
3.78
372.82
3.78
3 78
377.46
3.78
155.67
3.78
155.67
3.78
288.02
6.95
309.36
6.95
192.44
6.95
192.44
192 44
6.95
322.98
6.95
340.29
6.95
311.35
12.70
311.35
12.70
393.02
6.95
402.11
6.95
402.11
6.95
402.11
6.95
256.58
12.70
256.58
12.70
311.35
12 70
12.70
311.35
12.70
744.15
6.95
750.28
6.95
559.23
6.95
6 95
566.19
6.95
233.51
6.95
233.51
6.95
345.63
24.38
371.23
24.38
230.92
24.38
230.92
230 92
24.38
387.57
24.38
408.35
24.38
311.35
127.00
311.35
127.00
471.62
24.38
482.53
24.38
482.53
24.38
482.53
24.38
256.58
127.00
256.58
127.00
311.35
127 00
127.00
311.35
127.00
892.98
24.38
900.34
24.38
671.07
24.38
24 38
679.43
24.38
280.21
24.38
280.21
24.38
345.63
60.95
371.23
60.95
230.92
60.95
230.92
230 92
60.95
387.57
60.95
408.35
60.95
311.35
254.00
311.35
254.00
471.62
60.95
482.53
60.95
482.53
60.95
482.53
60.95
256.58
254.00
256.58
254.00
311.35
254 00
254.00
311.35
254.00
892.98
60.95
900.34
60.95
671.07
60.95
60 95
679.43
60.95
280.21
60.95
280.21
60.95
345.63
9.75
371.23
9.75
230.92
9.75
230.92
230 92
9.75
387.57
9.75
408.35
9.75
311.35
25.40
311.35
25.40
471.62
9.75
482.53
9.75
482.53
9.75
482.53
9.75
256.58
25.40
256.58
25.40
311.35
25 40
25.40
311.35
25.40
892.98
9.75
900.34
9.75
671.07
9.75
9 75
679.43
9.75
280.21
9.75
280.21
9.75
384.03
12.19
412.48
12.19
256.58
12.19
256.58
256 58
12.19
430.64
12.19
453.72
12.19
311.35
50.80
311.35
50.80
524.02
12.19
536.14
12.19
536.14
12.19
536.14
12.19
256.58
50.80
256.58
50.80
311.35
50 80
50.80
311.35
50.80
992.19
12.19
1000.38
12.19
745.64
12.19
12 19
754.92
12.19
311.35
12.19
311.35
12.19
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 18j
DEPTH
(m)
Soil
type
T1
Z1
T2
Z2
T3
T4
T5
Z3
Z4
Z5
* T (kN/m) Z (mm) *
T6
Z6
T7
Z7
78.4
Clay
79.2
Clay
79.2
Silt
81 0
81.0
Silt
81.0
Sand
86.0
Sand
86.0
Silt
88.6
Silt
88.6
Clay
90.8
Clay
90.8
Silt
93.0
Silt
93.0
Clay
97.0
Clay
97.0
Clay
102.5
Clay
102.5
Silt
103.4
Silt
103.4
Clay
106.0
Clay
106.0
Clay
107.3
Clay
240.74
1.95
241.96
1.95
93.40
1.95
93.40
93
40
1.95
311.35
2.54
311.35
2.54
311.35
2.54
311.35
2.54
229.78
1.95
229.78
1.95
311.35
2.54
311.35
2.54
183.82
1.95
275.73
1.95
183.82
1 95
1.95
183.82
1.95
256.58
2.54
256.58
2.54
183.82
1 95
1.95
183.82
1.95
275.73
1.95
275.73
1.95
401.24
3.78
403.26
3.78
155.67
3.78
155.67
155 67
3.78
311.35
5.08
311.35
5.08
311.35
5.08
311.35
5.08
382.96
3.78
382.96
3.78
311.35
5.08
311.35
5.08
306.37
3.78
459.55
3.78
306.37
3 78
3.78
306.37
3.78
256.58
5.08
256.58
5.08
306.37
3.78
3 78
306.37
3.78
459.55
3.78
459.55
3.78
601.86
6.95
604.89
6.95
233.51
6.95
233.51
233 51
6.95
311.35
12.70
311.35
12.70
311.35
12.70
311.35
12.70
574.44
6.95
574.44
6.95
311.35
12.70
311.35
12.70
459.55
6.95
689.33
6.95
459.55
6 95
6.95
459.55
6.95
256.58
12.70
256.58
12.70
459.55
6.95
6 95
459.55
6.95
689.33
6.95
689.33
6.95
722.23
24.38
725.87
24.38
280.21
24.38
280.21
280 21
24.38
311.35
127.00
311.35
127.00
311.35
127.00
311.35
127.00
689.33
24.38
689.33
24.38
311.35
127.00
311.35
127.00
551.46
24.38
827.19
24.38
551.46
24 38
24.38
551.46
24.38
256.58
127.00
256.58
127.00
551.46
24.38
24 38
551.46
24.38
827.19
24.38
827.19
24.38
722.23
60.95
725.87
60.95
280.21
60.95
280.21
280 21
60.95
311.35
254.00
311.35
254.00
311.35
254.00
311.35
254.00
689.33
60.95
689.33
60.95
311.35
254.00
311.35
254.00
551.46
60.95
827.19
60.95
551.46
60 95
60.95
551.46
60.95
256.58
254.00
256.58
254.00
551.46
60.95
60 95
551.46
60.95
827.19
60.95
827.19
60.95
722.23
9.75
725.87
9.75
280.21
9.75
280.21
280 21
9.75
311.35
25.40
311.35
25.40
311.35
25.40
311.35
25.40
689.33
9.75
689.33
9.75
311.35
25.40
311.35
25.40
551.46
9.75
827.19
9.75
551.46
9 75
9.75
551.46
9.75
256.58
25.40
256.58
25.40
551.46
9.75
9 75
551.46
9.75
827.19
9.75
827.19
9.75
802.48
12.19
806.52
12.19
311.35
12.19
311.35
311 35
12.19
311.35
50.80
311.35
50.80
311.35
50.80
311.35
50.80
765.92
12.19
765.92
12.19
311.35
50.80
311.35
50.80
612.74
12.19
919.10
12.19
612.74
12 19
12.19
612.74
12.19
256.58
50.80
256.58
50.80
612.74
12.19
12 19
612.74
12.19
919.10
12.19
919.10
12.19
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 18k
DEPTH
(m)
Soil
type
107.3
Sand
109.0
Sand
109.0
Clay
116 3
116.3
Clay
Cl
116.3
Sand
123.0
Sand
123.0
Clay
125.0
Clay
125.0
Sand
134.0
Sand
134.0
Clay
139.0
Clay
139.0
Clay
140.0
Clay
T1
Z1
311.35
2.54
311.35
2.54
765.92
2.54
765 92
765.92
2.54
311.35
2.54
311.35
2.54
229.78
1.95
229.78
1.95
311.35
2.54
311.35
2.54
1336.81
2.54
1362.49
2.54
252.75
1.95
252.75
1.95
T2
Z2
311.35
5.08
311.35
5.08
765.92
5.08
765.92
765 92
5.08
311.35
5.08
311.35
5.08
382.96
3.78
382.96
3.78
311.35
5.08
311.35
5.08
1336.81
5.08
1362.49
5.08
421.26
3.78
421.26
3.78
T3
T4
T5
Z3
Z4
Z5
* T (kN/m) Z (mm) *
311.35
12.70
311.35
12.70
765.92
12.70
765.92
765 92
12.70
311.35
12.70
311.35
12.70
574.44
6.95
574.44
6.95
311.35
12.70
311.35
12.70
1336.81
12.70
1362.49
12.70
631.88
6.95
631.88
6.95
311.35
25.40
311.35
25.40
765.92
25.40
765.92
765 92
25.40
311.35
25.40
311.35
25.40
689.33
9.75
689.33
9.75
311.35
25.40
311.35
25.40
1336.81
25.40
1362.49
25.40
758.26
9.75
758.26
9.75
311.35
50.80
311.35
50.80
765.92
50.80
765.92
765 92
50.80
311.35
50.80
311.35
50.80
765.92
12.19
765.92
12.19
311.35
50.80
311.35
50.80
1336.81
50.80
1362.49
50.80
842.51
12.19
842.51
12.19
T6
Z6
T7
Z7
311.35
127.00
311.35
127.00
765.92
127.00
765.92
765 92
127.00
311.35
127.00
311.35
127.00
689.33
24.38
689.33
24.38
311.35
127.00
311.35
127.00
1336.81
127.00
1362.49
127.00
758.26
24.38
758.26
24.38
311.35
254.00
311.35
254.00
765.92
254.00
765.92
765 92
254.00
311.35
254.00
311.35
254.00
689.33
60.95
689.33
60.95
311.35
254.00
311.35
254.00
1336.81
254.00
1362.49
254.00
758.26
60.95
758.26
60.95
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 18l
DEPTH
(m)
Soil
type
Q1
Z1
Q2
Z2
Q3
Z3
Q4
Q5
Z4
Z5
* Q (kN) Z (mm) *
0.0
Sand
3.1
Sand
3.1
Clay
4.2
Clay
4.2
Sand
5.2
Sand
5.2
Clay
7.5
Clay
7.5
Silt
10.0
Silt
10.0
Clay
15.0
Clay
15.0
Clay
19.0
Clay
19.0
Clay
23.0
Clay
23.0
Clay
27.0
Clay
27.0
Clay
30.0
Clay
30.0
Silt
33.0
Silt
33.0
Clay
38.0
Clay
0.00
1.52
5.19
1.52
13.23
1.52
13.23
1.52
7.37
1.52
9.27
1.52
26.45
1.52
26.45
1.52
102.44
1.52
134.59
1.52
26.45
1.52
205.22
1 52
1.52
82.09
1.52
82.09
1.52
128.26
1.52
128.26
1.52
205.22
1.52
205.22
1.52
246.26
1.52
246.26
1.52
330.63
1.52
330.63
1.52
123.13
1.52
123.13
1.52
0.00
9.91
10.39
9.91
26.45
9.91
26.45
9.91
14.73
9.91
18.54
9.91
52.90
9.91
52.90
9.91
204.89
9.91
269.19
9.91
52.90
9.91
410.43
9.91
9 91
164.17
9.91
164.17
9.91
256.52
9.91
256.52
9.91
410.43
9.91
410.43
9.91
492.52
9.91
492.52
9.91
661.25
9.91
661.25
9.91
246.26
9.91
246.26
9.91
0.00
19.05
13.92
19.05
35.44
19.05
35.44
19.05
19.74
19.05
24.84
19.05
70.89
19.05
70.89
19.05
274.55
19.05
360.71
19.05
70.89
19.05
549.98
19.05
19 05
219.99
19.05
219.99
19.05
343.74
19.05
343.74
19.05
549.98
19.05
549.98
19.05
659.98
19.05
659.98
19.05
886.08
19.05
886.08
19.05
329.99
19.05
329.99
19.05
0.00
32.00
15.58
32.00
39.68
32.00
39.68
32.00
22.10
32.00
27.81
32.00
79.35
32.00
79.35
32.00
307.33
32.00
403.78
32.00
79.35
32.00
615.65
32.00
32 00
246.26
32.00
246.26
32.00
384.78
32.00
384.78
32.00
615.65
32.00
615.65
32.00
738.78
32.00
738.78
32.00
991.88
32.00
991.88
32.00
369.39
32.00
369.39
32.00
0.00
55.63
18.69
55.63
47.61
55.63
47.61
55.63
26.52
55.63
33.37
55.63
95.22
55.63
95.22
55.63
368.80
55.63
484.54
55.63
95.22
55.63
738.78
55.63
55 63
295.51
55.63
295.51
55.63
461.74
55.63
461.74
55.63
738.78
55.63
738.78
55.63
886.54
55.63
886.54
55.63
1190.26
55.63
1190.26
55.63
443.27
55.63
443.27
55.63
Q6
Z6
Q7
Z7
0.00
76.20
20.77
76.20
52.90
76.20
52.90
76.20
29.46
76.20
37.08
76.20
105.80
76.20
105.80
76.20
409.78
76.20
538.38
76.20
105.80
76.20
820.87
76.20
76 20
328.35
76.20
328.35
76.20
513.04
76.20
513.04
76.20
820.87
76.20
820.87
76.20
985.04
76.20
985.04
76.20
1322.51
76.20
1322.51
76.20
492.52
76.20
492.52
76.20
0.00
381.00
20.77
381.00
52.90
381.00
52.90
381.00
29.46
381.00
37.08
381.00
105.80
381.00
105.80
381.00
409.78
381.00
538.38
381.00
105.80
381.00
820.87
381.00
381 00
328.35
381.00
328.35
381.00
513.04
381.00
513.04
381.00
820.87
381.00
820.87
381.00
985.04
381.00
985.04
381.00
1322.51
381.00
1322.51
381.00
492.52
381.00
492.52
381.00
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 19a
DEPTH
(m)
Soil
type
38.0
Silt
41.0
Silt
41.0
Clay
45.0
Clay
45.0
Silt
51.7
Silt
51.7
Clay
58.0
Clay
58.0
Clay
65.6
Clay
65.6
Sand
67.0
Sand
67.0
Silt
73.0
Silt
73.0
Silt
74.3
Silt
74.3
Clay
76.3
Clay
76.3
Silt
78.4
Silt
78.4
Clay
79.2
Clay
79.2
Silt
81.0
Silt
Q1
Z1
Q2
Z2
330.63
1.52
330.63
1.52
123.13
1.52
123.13
1.52
547.24
1.52
547.24
1.52
143.65
1.52
143.65
1.52
143.65
1.52
143.65
1.52
330.63
1.52
330.63
1 52
1.52
547.24
1.52
547.24
1.52
369.39
1.52
369.39
1.52
205.22
1.52
205.22
1.52
547.24
1.52
547.24
1.52
225.74
1.52
225.74
1.52
547.24
1.52
547.24
1.52
661.25
9.91
661.25
9.91
246.26
9.91
246.26
9.91
1094.49
9.91
1094.49
9.91
287.30
9.91
287.30
9.91
287.30
9.91
287.30
9.91
661.25
9.91
661.25
9.91
9 91
1094.49
9.91
1094.49
9.91
738.78
9.91
738.78
9.91
410.43
9.91
410.43
9.91
1094.49
9.91
1094.49
9.91
451.48
9.91
451.48
9.91
1094.49
9.91
1094.49
9.91
Q3
Z3
Q4
Q5
Z4
Z5
* Q (kN) Z (mm) *
886.08
19.05
886.08
19.05
329.99
19.05
329.99
19.05
1466.61
19.05
1466.61
19.05
384.99
19.05
384.99
19.05
384.99
19.05
384.99
19.05
886.08
19.05
886.08
19.05
19 05
1466.61
19.05
1466.61
19.05
989.96
19.05
989.96
19.05
549.98
19.05
549.98
19.05
1466.61
19.05
1466.61
19.05
604.98
19.05
604.98
19.05
1466.61
19.05
1466.61
19.05
991.88
32.00
991.88
32.00
369.39
32.00
369.39
32.00
1641.73
32.00
1641.73
32.00
430.95
32.00
430.95
32.00
430.95
32.00
430.95
32.00
991.88
32.00
991.88
32.00
32 00
1641.73
32.00
1641.73
32.00
1108.17
32.00
1108.17
32.00
615.65
32.00
615.65
32.00
1641.73
32.00
1641.73
32.00
677.21
32.00
677.21
32.00
1641.73
32.00
1641.73
32.00
1190.26
55.63
1190.26
55.63
443.27
55.63
443.27
55.63
1970.08
55.63
1970.08
55.63
517.15
55.63
517.15
55.63
517.15
55.63
517.15
55.63
1190.26
55.63
1190.26
55.63
55 63
1970.08
55.63
1970.08
55.63
1329.80
55.63
1329.80
55.63
738.78
55.63
738.78
55.63
1970.08
55.63
1970.08
55.63
812.66
55.63
812.66
55.63
1970.08
55.63
1970.08
55.63
Q6
Z6
Q7
Z7
1322.51
76.20
1322.51
76.20
492.52
76.20
492.52
76.20
2188.98
76.20
2188.98
76.20
574.61
76.20
574.61
76.20
574.61
76.20
574.61
76.20
1322.51
76.20
1322.51
76.20
76 20
2188.98
76.20
2188.98
76.20
1477.56
76.20
1477.56
76.20
820.87
76.20
820.87
76.20
2188.98
76.20
2188.98
76.20
902.95
76.20
902.95
76.20
2188.98
76.20
2188.98
76.20
1322.51
381.00
1322.51
381.00
492.52
381.00
492.52
381.00
2188.98
381.00
2188.98
381.00
574.61
381.00
574.61
381.00
574.61
381.00
574.61
381.00
1322.51
381.00
1322.51
381.00
381 00
2188.98
381.00
2188.98
381.00
1477.56
381.00
1477.56
381.00
820.87
381.00
820.87
381.00
2188.98
381.00
2188.98
381.00
902.95
381.00
902.95
381.00
2188.98
381.00
2188.98
381.00
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 19b
DEPTH
(m)
Soil
type
Q1
Z1
Q2
Z2
81.0
Sand
86.0
Sand
86.0
Silt
88.6
Silt
88.6
Clay
90.8
Clay
90.8
Silt
93.0
Silt
93.0
Clay
97.0
Clay
97.0
Clay
102.5
Clay
102.5
Silt
103.4
Silt
103.4
Clay
106.0
Clay
106.0
Clay
107.3
Clay
107.3
Sand
109.0
Sand
109.0
Clay
116.3
Clay
116.3
Sand
123.0
Sand
547.24
1.52
547.24
1.52
547.24
1.52
547.24
1.52
205.22
1.52
205.22
1.52
547.24
1.52
547.24
1.52
164.17
1.52
246.26
1.52
164.17
1.52
164.17
1 52
1.52
330.63
1.52
330.63
1.52
164.17
1.52
164.17
1.52
246.26
1.52
246.26
1.52
547.24
1.52
547.24
1.52
205.22
1.52
205.22
1.52
547.24
1.52
547.24
1.52
1094.49
9.91
1094.49
9.91
1094.49
9.91
1094.49
9.91
410.43
9.91
410.43
9.91
1094.49
9.91
1094.49
9.91
328.35
9.91
492.52
9.91
328.35
9.91
328.35
9.91
9 91
661.25
9.91
661.25
9.91
328.35
9.91
328.35
9.91
492.52
9.91
492.52
9.91
1094.49
9.91
1094.49
9.91
410.43
9.91
410.43
9.91
1094.49
9.91
1094.49
9.91
Q3
Z3
Q4
Q5
Z4
Z5
* Q (kN) Z (mm) *
1466.61
19.05
1466.61
19.05
1466.61
19.05
1466.61
19.05
549.98
19.05
549.98
19.05
1466.61
19.05
1466.61
19.05
439.98
19.05
659.98
19.05
439.98
19.05
439.98
19.05
19 05
886.08
19.05
886.08
19.05
439.98
19.05
439.98
19.05
659.98
19.05
659.98
19.05
1466.61
19.05
1466.61
19.05
549.98
19.05
549.98
19.05
1466.61
19.05
1466.61
19.05
1641.73
32.00
1641.73
32.00
1641.73
32.00
1641.73
32.00
615.65
32.00
615.65
32.00
1641.73
32.00
1641.73
32.00
492.52
32.00
738.78
32.00
492.52
32.00
492.52
32.00
32 00
991.88
32.00
991.88
32.00
492.52
32.00
492.52
32.00
738.78
32.00
738.78
32.00
1641.73
32.00
1641.73
32.00
615.65
32.00
615.65
32.00
1641.73
32.00
1641.73
32.00
1970.08
55.63
1970.08
55.63
1970.08
55.63
1970.08
55.63
738.78
55.63
738.78
55.63
1970.08
55.63
1970.08
55.63
591.02
55.63
886.54
55.63
591.02
55.63
591.02
55.63
55 63
1190.26
55.63
1190.26
55.63
591.02
55.63
591.02
55.63
886.54
55.63
886.54
55.63
1970.08
55.63
1970.08
55.63
738.78
55.63
738.78
55.63
1970.08
55.63
1970.08
55.63
Q6
Z6
Q7
Z7
2188.98
76.20
2188.98
76.20
2188.98
76.20
2188.98
76.20
820.87
76.20
820.87
76.20
2188.98
76.20
2188.98
76.20
656.69
76.20
985.04
76.20
656.69
76.20
656.69
76.20
76 20
1322.51
76.20
1322.51
76.20
656.69
76.20
656.69
76.20
985.04
76.20
985.04
76.20
2188.98
76.20
2188.98
76.20
820.87
76.20
820.87
76.20
2188.98
76.20
2188.98
76.20
2188.98
381.00
2188.98
381.00
2188.98
381.00
2188.98
381.00
820.87
381.00
820.87
381.00
2188.98
381.00
2188.98
381.00
656.69
381.00
985.04
381.00
656.69
381.00
656.69
381.00
381 00
1322.51
381.00
1322.51
381.00
656.69
381.00
656.69
381.00
985.04
381.00
985.04
381.00
2188.98
381.00
2188.98
381.00
820.87
381.00
820.87
381.00
2188.98
381.00
2188.98
381.00
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 19c
DEPTH
(m)
Soil
type
Q1
Z1
Q2
Z2
123.0
Clay
125.0
Clay
125.0
Sand
134.0
Sand
134.0
Clay
139.0
Clay
139.0
Clay
140.0
Clay
205.22
1.52
205.22
1.52
547.24
1.52
547.24
1.52
369.39
1.52
369.39
1.52
225.74
1.52
225.74
1.52
410.43
9.91
410.43
9.91
1094.49
9.91
1094.49
9.91
738.78
9.91
738.78
9.91
451.48
9.91
451.48
9.91
Q3
Z3
Q4
Q5
Z4
Z5
* Q (kN) Z (mm) *
549.98
19.05
549.98
19.05
1466.61
19.05
1466.61
19.05
989.96
19.05
989.96
19.05
604.98
19.05
604.98
19.05
615.65
32.00
615.65
32.00
1641.73
32.00
1641.73
32.00
1108.17
32.00
1108.17
32.00
677.21
32.00
677.21
32.00
738.78
55.63
738.78
55.63
1970.08
55.63
1970.08
55.63
1329.80
55.63
1329.80
55.63
812.66
55.63
812.66
55.63
Q6
Z6
Q7
Z7
820.87
76.20
820.87
76.20
2188.98
76.20
2188.98
76.20
1477.56
76.20
1477.56
76.20
902.95
76.20
902.95
76.20
820.87
381.00
820.87
381.00
2188.98
381.00
2188.98
381.00
1477.56
381.00
1477.56
381.00
902.95
381.00
902.95
381.00
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 19d
DEPTH
(m)
Soil
type
Q1
Z1
Q2
Z2
0.0
Sand
3.1
Sand
3.1
Clay
4.2
Clay
4.2
Sand
5.2
Sand
5.2
Clay
7.5
Clay
7.5
Silt
10.0
Silt
10.0
Clay
15.0
Clay
15.0
Clay
19.0
Clay
19.0
Clay
23.0
Clay
23.0
Clay
27.0
Clay
27.0
Clay
30.0
Clay
30.0
Silt
33.0
Silt
33.0
Clay
38.0
Clay
0.00
1.83
9.27
1.83
23.60
1.83
23.60
1.83
13.14
1.83
16.54
1.83
47.20
1.83
47.20
1.83
147.52
1.83
193.82
1.83
47.20
1.83
295.51
1 83
1.83
118.20
1.83
118.20
1.83
184.69
1.83
184.69
1.83
295.51
1.83
295.51
1.83
354.61
1.83
354.61
1.83
476.10
1.83
476.10
1.83
177.31
1.83
177.31
1.83
0.00
11.89
18.53
11.89
47.20
11.89
47.20
11.89
26.29
11.89
33.08
11.89
94.40
11.89
94.40
11.89
295.04
11.89
387.63
11.89
94.40
11.89
591.02
11.89
11 89
236.41
11.89
236.41
11.89
369.39
11.89
369.39
11.89
591.02
11.89
591.02
11.89
709.23
11.89
709.23
11.89
952.20
11.89
952.20
11.89
354.61
11.89
354.61
11.89
Q3
Z3
Q4
Q5
Z4
Z5
* Q (kN) Z (mm) *
0.00
22.86
24.84
22.86
63.25
22.86
63.25
22.86
35.22
22.86
44.33
22.86
126.50
22.86
126.50
22.86
395.35
22.86
519.43
22.86
126.50
22.86
791.97
22.86
22 86
316.79
22.86
316.79
22.86
494.98
22.86
494.98
22.86
791.97
22.86
791.97
22.86
950.37
22.86
950.37
22.86
1275.95
22.86
1275.95
22.86
475.18
22.86
475.18
22.86
0.00
38.40
27.80
38.40
70.80
38.40
70.80
38.40
39.43
38.40
49.63
38.40
141.60
38.40
141.60
38.40
442.56
38.40
581.45
38.40
141.60
38.40
886.54
38.40
38 40
354.61
38.40
354.61
38.40
554.08
38.40
554.08
38.40
886.54
38.40
886.54
38.40
1063.84
38.40
1063.84
38.40
1428.31
38.40
1428.31
38.40
531.92
38.40
531.92
38.40
0.00
66.75
33.36
66.75
84.96
66.75
84.96
66.75
47.32
66.75
59.55
66.75
169.92
66.75
169.92
66.75
531.07
66.75
697.74
66.75
169.92
66.75
1063.84
66.75
66 75
425.54
66.75
425.54
66.75
664.90
66.75
664.90
66.75
1063.84
66.75
1063.84
66.75
1276.61
66.75
1276.61
66.75
1713.97
66.75
1713.97
66.75
638.31
66.75
638.31
66.75
Q6
Z6
Q7
Z7
0.00
91.44
37.07
91.44
94.40
91.44
94.40
91.44
52.57
91.44
66.17
91.44
188.80
91.44
188.80
91.44
590.08
91.44
775.27
91.44
188.80
91.44
1182.05
91.44
91 44
472.82
91.44
472.82
91.44
738.78
91.44
738.78
91.44
1182.05
91.44
1182.05
91.44
1418.46
91.44
1418.46
91.44
1904.41
91.44
1904.41
91.44
709.23
91.44
709.23
91.44
0.00
457.20
37.07
457.20
94.40
457.20
94.40
457.20
52.57
457.20
66.17
457.20
188.80
457.20
188.80
457.20
590.08
457.20
775.27
457.20
188.80
457.20
1182.05
457.20
457 20
472.82
457.20
472.82
457.20
738.78
457.20
738.78
457.20
1182.05
457.20
1182.05
457.20
1418.46
457.20
1418.46
457.20
1904.41
457.20
1904.41
457.20
709.23
457.20
709.23
457.20
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 19e
DEPTH
(m)
Soil
type
38.0
Silt
41.0
Silt
41.0
Clay
45.0
Clay
45.0
Silt
51.7
Silt
51.7
Clay
58.0
Clay
58.0
Clay
65.6
Clay
65.6
Sand
67.0
Sand
67.0
Silt
73.0
Silt
73.0
Silt
74.3
Silt
74.3
Clay
76.3
Clay
76.3
Silt
78.4
Silt
78.4
Clay
79.2
Clay
79.2
Silt
81.0
Silt
Q1
Z1
Q2
Z2
476.10
1.83
476.10
1.83
177.31
1.83
177.31
1.83
788.03
1.83
788.03
1.83
206.86
1.83
206.86
1.83
206.86
1.83
206.86
1.83
476.10
1.83
476.10
1 83
1.83
788.03
1.83
788.03
1.83
531.92
1.83
531.92
1.83
295.51
1.83
295.51
1.83
788.03
1.83
788.03
1.83
325.06
1.83
325.06
1.83
788.03
1.83
788.03
1.83
952.20
11.89
952.20
11.89
354.61
11.89
354.61
11.89
1576.06
11.89
1576.06
11.89
413.72
11.89
413.72
11.89
413.72
11.89
413.72
11.89
952.20
11.89
952.20
11.89
11 89
1576.06
11.89
1576.06
11.89
1063.84
11.89
1063.84
11.89
591.02
11.89
591.02
11.89
1576.06
11.89
1576.06
11.89
650.13
11.89
650.13
11.89
1576.06
11.89
1576.06
11.89
Q3
Z3
Q4
Q5
Z4
Z5
* Q (kN) Z (mm) *
1275.95
22.86
1275.95
22.86
475.18
22.86
475.18
22.86
2111.92
22.86
2111.92
22.86
554.38
22.86
554.38
22.86
554.38
22.86
554.38
22.86
1275.95
22.86
1275.95
22.86
22 86
2111.92
22.86
2111.92
22.86
1425.55
22.86
1425.55
22.86
791.97
22.86
791.97
22.86
2111.92
22.86
2111.92
22.86
871.17
22.86
871.17
22.86
2111.92
22.86
2111.92
22.86
1428.31
38.40
1428.31
38.40
531.92
38.40
531.92
38.40
2364.09
38.40
2364.09
38.40
620.57
38.40
620.57
38.40
620.57
38.40
620.57
38.40
1428.31
38.40
1428.31
38.40
38 40
2364.09
38.40
2364.09
38.40
1595.76
38.40
1595.76
38.40
886.54
38.40
886.54
38.40
2364.09
38.40
2364.09
38.40
975.19
38.40
975.19
38.40
2364.09
38.40
2364.09
38.40
1713.97
66.75
1713.97
66.75
638.31
66.75
638.31
66.75
2836.91
66.75
2836.91
66.75
744.69
66.75
744.69
66.75
744.69
66.75
744.69
66.75
1713.97
66.75
1713.97
66.75
66 75
2836.91
66.75
2836.91
66.75
1914.92
66.75
1914.92
66.75
1063.84
66.75
1063.84
66.75
2836.91
66.75
2836.91
66.75
1170.23
66.75
1170.23
66.75
2836.91
66.75
2836.91
66.75
Q6
Z6
Q7
Z7
1904.41
91.44
1904.41
91.44
709.23
91.44
709.23
91.44
3152.13
91.44
3152.13
91.44
827.43
91.44
827.43
91.44
827.43
91.44
827.43
91.44
1904.41
91.44
1904.41
91.44
91 44
3152.13
91.44
3152.13
91.44
2127.68
91.44
2127.68
91.44
1182.05
91.44
1182.05
91.44
3152.13
91.44
3152.13
91.44
1300.25
91.44
1300.25
91.44
3152.13
91.44
3152.13
91.44
1904.41
457.20
1904.41
457.20
709.23
457.20
709.23
457.20
3152.13
457.20
3152.13
457.20
827.43
457.20
827.43
457.20
827.43
457.20
827.43
457.20
1904.41
457.20
1904.41
457.20
457 20
3152.13
457.20
3152.13
457.20
2127.68
457.20
2127.68
457.20
1182.05
457.20
1182.05
457.20
3152.13
457.20
3152.13
457.20
1300.25
457.20
1300.25
457.20
3152.13
457.20
3152.13
457.20
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 19f
DEPTH
(m)
Soil
type
Q1
Z1
Q2
Z2
81.0
Sand
86.0
Sand
86.0
Silt
88.6
Silt
88.6
Clay
90.8
Clay
90.8
Silt
93.0
Silt
93.0
Clay
97.0
Clay
97.0
Clay
102.5
Clay
102.5
Silt
103.4
Silt
103.4
Clay
106.0
Clay
106.0
Clay
107.3
Clay
107.3
Sand
109.0
Sand
109.0
Clay
116.3
Clay
116.3
Sand
123.0
Sand
788.03
1.83
788.03
1.83
788.03
1.83
788.03
1.83
295.51
1.83
295.51
1.83
788.03
1.83
788.03
1.83
236.41
1.83
354.61
1.83
236.41
1.83
236.41
1 83
1.83
476.10
1.83
476.10
1.83
236.41
1.83
236.41
1.83
354.61
1.83
354.61
1.83
788.03
1.83
788.03
1.83
295.51
1.83
295.51
1.83
788.03
1.83
788.03
1.83
1576.06
11.89
1576.06
11.89
1576.06
11.89
1576.06
11.89
591.02
11.89
591.02
11.89
1576.06
11.89
1576.06
11.89
472.82
11.89
709.23
11.89
472.82
11.89
472.82
11.89
11 89
952.20
11.89
952.20
11.89
472.82
11.89
472.82
11.89
709.23
11.89
709.23
11.89
1576.06
11.89
1576.06
11.89
591.02
11.89
591.02
11.89
1576.06
11.89
1576.06
11.89
Q3
Z3
Q4
Q5
Z4
Z5
* Q (kN) Z (mm) *
2111.92
22.86
2111.92
22.86
2111.92
22.86
2111.92
22.86
791.97
22.86
791.97
22.86
2111.92
22.86
2111.92
22.86
633.58
22.86
950.37
22.86
633.58
22.86
633.58
22.86
22 86
1275.95
22.86
1275.95
22.86
633.58
22.86
633.58
22.86
950.37
22.86
950.37
22.86
2111.92
22.86
2111.92
22.86
791.97
22.86
791.97
22.86
2111.92
22.86
2111.92
22.86
2364.09
38.40
2364.09
38.40
2364.09
38.40
2364.09
38.40
886.54
38.40
886.54
38.40
2364.09
38.40
2364.09
38.40
709.23
38.40
1063.84
38.40
709.23
38.40
709.23
38.40
38 40
1428.31
38.40
1428.31
38.40
709.23
38.40
709.23
38.40
1063.84
38.40
1063.84
38.40
2364.09
38.40
2364.09
38.40
886.54
38.40
886.54
38.40
2364.09
38.40
2364.09
38.40
2836.91
66.75
2836.91
66.75
2836.91
66.75
2836.91
66.75
1063.84
66.75
1063.84
66.75
2836.91
66.75
2836.91
66.75
851.07
66.75
1276.61
66.75
851.07
66.75
851.07
66.75
66 75
1713.97
66.75
1713.97
66.75
851.07
66.75
851.07
66.75
1276.61
66.75
1276.61
66.75
2836.91
66.75
2836.91
66.75
1063.84
66.75
1063.84
66.75
2836.91
66.75
2836.91
66.75
Q6
Z6
Q7
Z7
3152.13
91.44
3152.13
91.44
3152.13
91.44
3152.13
91.44
1182.05
91.44
1182.05
91.44
3152.13
91.44
3152.13
91.44
945.64
91.44
1418.46
91.44
945.64
91.44
945.64
91.44
91 44
1904.41
91.44
1904.41
91.44
945.64
91.44
945.64
91.44
1418.46
91.44
1418.46
91.44
3152.13
91.44
3152.13
91.44
1182.05
91.44
1182.05
91.44
3152.13
91.44
3152.13
91.44
3152.13
457.20
3152.13
457.20
3152.13
457.20
3152.13
457.20
1182.05
457.20
1182.05
457.20
3152.13
457.20
3152.13
457.20
945.64
457.20
1418.46
457.20
945.64
457.20
945.64
457.20
457 20
1904.41
457.20
1904.41
457.20
945.64
457.20
945.64
457.20
1418.46
457.20
1418.46
457.20
3152.13
457.20
3152.13
457.20
1182.05
457.20
1182.05
457.20
3152.13
457.20
3152.13
457.20
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 19g
DEPTH
(m)
Soil
type
Q1
Z1
Q2
Z2
123.0
Clay
125.0
Clay
125.0
Sand
134.0
Sand
134.0
Clay
139.0
Clay
139.0
Clay
140.0
Clay
295.51
1.83
295.51
1.83
788.03
1.83
788.03
1.83
531.92
1.83
531.92
1.83
325.06
1.83
325.06
1.83
591.02
11.89
591.02
11.89
1576.06
11.89
1576.06
11.89
1063.84
11.89
1063.84
11.89
650.13
11.89
650.13
11.89
Q3
Z3
Q4
Q5
Z4
Z5
* Q (kN) Z (mm) *
791.97
22.86
791.97
22.86
2111.92
22.86
2111.92
22.86
1425.55
22.86
1425.55
22.86
871.17
22.86
871.17
22.86
886.54
38.40
886.54
38.40
2364.09
38.40
2364.09
38.40
1595.76
38.40
1595.76
38.40
975.19
38.40
975.19
38.40
1063.84
66.75
1063.84
66.75
2836.91
66.75
2836.91
66.75
1914.92
66.75
1914.92
66.75
1170.23
66.75
1170.23
66.75
Q6
Z6
Q7
Z7
1182.05
91.44
1182.05
91.44
3152.13
91.44
3152.13
91.44
2127.68
91.44
2127.68
91.44
1300.25
91.44
1300.25
91.44
1182.05
457.20
1182.05
457.20
3152.13
457.20
3152.13
457.20
2127.68
457.20
2127.68
457.20
1300.25
457.20
1300.25
457.20
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 19h
DEPTH
(m)
Soil
type
Q1
Z1
Q2
Z2
0.0
Sand
3.1
Sand
3.1
Clay
4.2
Clay
4.2
Sand
5.2
Sand
5.2
Clay
7.5
Clay
7.5
Silt
10.0
Silt
10.0
Clay
15.0
Clay
15.0
Clay
19.0
Clay
19.0
Clay
23.0
Clay
23.0
Clay
27.0
Clay
27.0
Clay
30.0
Clay
30.0
Silt
33.0
Silt
33.0
Clay
38.0
Clay
0.00
2.44
16.24
2.44
41.35
2.44
41.35
2.44
23.03
2.44
28.99
2.44
82.71
2.44
82.71
2.44
262.26
2.44
344.56
2.44
82.71
2.44
525.35
2 44
2.44
210.14
2.44
210.14
2.44
328.35
2.44
328.35
2.44
525.35
2.44
525.35
2.44
630.43
2.44
630.43
2.44
846.40
2.44
846.40
2.44
315.21
2.44
315.21
2.44
0.00
15.85
32.48
15.85
82.71
15.85
82.71
15.85
46.06
15.85
57.97
15.85
165.41
15.85
165.41
15.85
524.51
15.85
689.12
15.85
165.41
15.85
1050.71
15.85
15 85
420.28
15.85
420.28
15.85
656.69
15.85
656.69
15.85
1050.71
15.85
1050.71
15.85
1260.85
15.85
1260.85
15.85
1692.81
15.85
1692.81
15.85
630.43
15.85
630.43
15.85
Q3
Z3
Q4
Q5
Z4
Z5
* Q (kN) Z (mm) *
0.00
30.48
43.52
30.48
110.83
30.48
110.83
30.48
61.72
30.48
77.68
30.48
221.65
30.48
221.65
30.48
702.85
30.48
923.43
30.48
221.65
30.48
1407.95
30.48
30 48
563.18
30.48
563.18
30.48
879.97
30.48
879.97
30.48
1407.95
30.48
1407.95
30.48
1689.54
30.48
1689.54
30.48
2268.36
30.48
2268.36
30.48
844.77
30.48
844.77
30.48
0.00
51.21
48.71
51.21
124.06
51.21
124.06
51.21
69.09
51.21
86.96
51.21
248.12
51.21
248.12
51.21
786.77
51.21
1033.69
51.21
248.12
51.21
1576.06
51.21
51 21
630.43
51.21
630.43
51.21
985.04
51.21
985.04
51.21
1576.06
51.21
1576.06
51.21
1891.28
51.21
1891.28
51.21
2539.21
51.21
2539.21
51.21
945.64
51.21
945.64
51.21
0.00
89.00
58.46
89.00
148.87
89.00
148.87
89.00
82.91
89.00
104.35
89.00
297.74
89.00
297.74
89.00
944.12
89.00
1240.42
89.00
297.74
89.00
1891.28
89.00
89 00
756.51
89.00
756.51
89.00
1182.05
89.00
1182.05
89.00
1891.28
89.00
1891.28
89.00
2269.53
89.00
2269.53
89.00
3047.06
89.00
3047.06
89.00
1134.77
89.00
1134.77
89.00
Q6
Z6
Q7
Z7
0.00
121.92
64.95
121.92
165.41
121.92
165.41
121.92
92.12
121.92
115.94
121.92
330.82
121.92
330.82
121.92
1049.03
121.92
1378.25
121.92
330.82
121.92
2101.42
121.92
121 92
840.57
121.92
840.57
121.92
1313.39
121.92
1313.39
121.92
2101.42
121.92
2101.42
121.92
2521.70
121.92
2521.70
121.92
3385.62
121.92
3385.62
121.92
1260.85
121.92
1260.85
121.92
0.00
609.60
64.95
609.60
165.41
609.60
165.41
609.60
92.12
609.60
115.94
609.60
330.82
609.60
330.82
609.60
1049.03
609.60
1378.25
609.60
330.82
609.60
2101.42
609.60
609 60
840.57
609.60
840.57
609.60
1313.39
609.60
1313.39
609.60
2101.42
609.60
2101.42
609.60
2521.70
609.60
2521.70
609.60
3385.62
609.60
3385.62
609.60
1260.85
609.60
1260.85
609.60
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 19i
DEPTH
(m)
Soil
type
38.0
Silt
41.0
Silt
41.0
Clay
45.0
Clay
45.0
Silt
51.7
Silt
51.7
Clay
58.0
Clay
58.0
Clay
65.6
Clay
65.6
Sand
67.0
Sand
67.0
Silt
73.0
Silt
73.0
Silt
74.3
Silt
74.3
Clay
76.3
Clay
76.3
Silt
78.4
Silt
78.4
Clay
79.2
Clay
79.2
Silt
81.0
Silt
Q1
Z1
Q2
Z2
846.40
2.44
846.40
2.44
315.21
2.44
315.21
2.44
1400.94
2.44
1400.94
2.44
367.75
2.44
367.75
2.44
367.75
2.44
367.75
2.44
846.40
2.44
846.40
2 44
2.44
1400.94
2.44
1400.94
2.44
945.64
2.44
945.64
2.44
525.35
2.44
525.35
2.44
1400.94
2.44
1400.94
2.44
577.89
2.44
577.89
2.44
1400.94
2.44
1400.94
2.44
1692.81
15.85
1692.81
15.85
630.43
15.85
630.43
15.85
2801.89
15.85
2801.89
15.85
735.50
15.85
735.50
15.85
735.50
15.85
735.50
15.85
1692.81
15.85
1692.81
15.85
15 85
2801.89
15.85
2801.89
15.85
1891.28
15.85
1891.28
15.85
1050.71
15.85
1050.71
15.85
2801.89
15.85
2801.89
15.85
1155.78
15.85
1155.78
15.85
2801.89
15.85
2801.89
15.85
Q3
Z3
Q4
Q5
Z4
Z5
* Q (kN) Z (mm) *
2268.36
30.48
2268.36
30.48
844.77
30.48
844.77
30.48
3754.53
30.48
3754.53
30.48
985.56
30.48
985.56
30.48
985.56
30.48
985.56
30.48
2268.36
30.48
2268.36
30.48
30 48
3754.53
30.48
3754.53
30.48
2534.31
30.48
2534.31
30.48
1407.95
30.48
1407.95
30.48
3754.53
30.48
3754.53
30.48
1548.74
30.48
1548.74
30.48
3754.53
30.48
3754.53
30.48
2539.21
51.21
2539.21
51.21
945.64
51.21
945.64
51.21
4202.83
51.21
4202.83
51.21
1103.24
51.21
1103.24
51.21
1103.24
51.21
1103.24
51.21
2539.21
51.21
2539.21
51.21
51 21
4202.83
51.21
4202.83
51.21
2836.91
51.21
2836.91
51.21
1576.06
51.21
1576.06
51.21
4202.83
51.21
4202.83
51.21
1733.67
51.21
1733.67
51.21
4202.83
51.21
4202.83
51.21
3047.06
89.00
3047.06
89.00
1134.77
89.00
1134.77
89.00
5043.40
89.00
5043.40
89.00
1323.89
89.00
1323.89
89.00
1323.89
89.00
1323.89
89.00
3047.06
89.00
3047.06
89.00
89 00
5043.40
89.00
5043.40
89.00
3404.30
89.00
3404.30
89.00
1891.28
89.00
1891.28
89.00
5043.40
89.00
5043.40
89.00
2080.40
89.00
2080.40
89.00
5043.40
89.00
5043.40
89.00
Q6
Z6
Q7
Z7
3385.62
121.92
3385.62
121.92
1260.85
121.92
1260.85
121.92
5603.78
121.92
5603.78
121.92
1470.99
121.92
1470.99
121.92
1470.99
121.92
1470.99
121.92
3385.62
121.92
3385.62
121.92
121 92
5603.78
121.92
5603.78
121.92
3782.55
121.92
3782.55
121.92
2101.42
121.92
2101.42
121.92
5603.78
121.92
5603.78
121.92
2311.56
121.92
2311.56
121.92
5603.78
121.92
5603.78
121.92
3385.62
609.60
3385.62
609.60
1260.85
609.60
1260.85
609.60
5603.78
609.60
5603.78
609.60
1470.99
609.60
1470.99
609.60
1470.99
609.60
1470.99
609.60
3385.62
609.60
3385.62
609.60
609 60
5603.78
609.60
5603.78
609.60
3782.55
609.60
3782.55
609.60
2101.42
609.60
2101.42
609.60
5603.78
609.60
5603.78
609.60
2311.56
609.60
2311.56
609.60
5603.78
609.60
5603.78
609.60
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 19j
DEPTH
(m)
Soil
type
81.0
Sand
86.0
Sand
86.0
Silt
88.6
Silt
88.6
Clay
90.8
Clay
90.8
Silt
93.0
Silt
93.0
Clay
97.0
Clay
97.0
Clay
102.5
Clay
102.5
Silt
103.4
Silt
103.4
Clay
106.0
Clay
106.0
Clay
107.3
Clay
107.3
Sand
109.0
Sand
109.0
Clay
116.3
Clay
116.3
Sand
123.0
Sand
Q1
Z1
Q2
Z2
1400.94
2.44
1400.94
2.44
1400.94
2.44
1400.94
2.44
525.35
2.44
525.35
2.44
1400.94
2.44
1400.94
2.44
420.28
2.44
630.43
2.44
420.28
2.44
420.28
2 44
2.44
846.40
2.44
846.40
2.44
420.28
2.44
420.28
2.44
630.43
2.44
630.43
2.44
1400.94
2.44
1400.94
2.44
525.35
2.44
525.35
2.44
1400.94
2.44
1400.94
2.44
2801.89
15.85
2801.89
15.85
2801.89
15.85
2801.89
15.85
1050.71
15.85
1050.71
15.85
2801.89
15.85
2801.89
15.85
840.57
15.85
1260.85
15.85
840.57
15.85
840.57
15.85
15 85
1692.81
15.85
1692.81
15.85
840.57
15.85
840.57
15.85
1260.85
15.85
1260.85
15.85
2801.89
15.85
2801.89
15.85
1050.71
15.85
1050.71
15.85
2801.89
15.85
2801.89
15.85
Q3
Z3
Q4
Q5
Z4
Z5
* Q (kN) Z (mm) *
3754.53
30.48
3754.53
30.48
3754.53
30.48
3754.53
30.48
1407.95
30.48
1407.95
30.48
3754.53
30.48
3754.53
30.48
1126.36
30.48
1689.54
30.48
1126.36
30.48
1126.36
30.48
30 48
2268.36
30.48
2268.36
30.48
1126.36
30.48
1126.36
30.48
1689.54
30.48
1689.54
30.48
3754.53
30.48
3754.53
30.48
1407.95
30.48
1407.95
30.48
3754.53
30.48
3754.53
30.48
4202.83
51.21
4202.83
51.21
4202.83
51.21
4202.83
51.21
1576.06
51.21
1576.06
51.21
4202.83
51.21
4202.83
51.21
1260.85
51.21
1891.28
51.21
1260.85
51.21
1260.85
51.21
51 21
2539.21
51.21
2539.21
51.21
1260.85
51.21
1260.85
51.21
1891.28
51.21
1891.28
51.21
4202.83
51.21
4202.83
51.21
1576.06
51.21
1576.06
51.21
4202.83
51.21
4202.83
51.21
5043.40
89.00
5043.40
89.00
5043.40
89.00
5043.40
89.00
1891.28
89.00
1891.28
89.00
5043.40
89.00
5043.40
89.00
1513.02
89.00
2269.53
89.00
1513.02
89.00
1513.02
89.00
89 00
3047.06
89.00
3047.06
89.00
1513.02
89.00
1513.02
89.00
2269.53
89.00
2269.53
89.00
5043.40
89.00
5043.40
89.00
1891.28
89.00
1891.28
89.00
5043.40
89.00
5043.40
89.00
Q6
Z6
Q7
Z7
5603.78
121.92
5603.78
121.92
5603.78
121.92
5603.78
121.92
2101.42
121.92
2101.42
121.92
5603.78
121.92
5603.78
121.92
1681.13
121.92
2521.70
121.92
1681.13
121.92
1681.13
121.92
121 92
3385.62
121.92
3385.62
121.92
1681.13
121.92
1681.13
121.92
2521.70
121.92
2521.70
121.92
5603.78
121.92
5603.78
121.92
2101.42
121.92
2101.42
121.92
5603.78
121.92
5603.78
121.92
5603.78
609.60
5603.78
609.60
5603.78
609.60
5603.78
609.60
2101.42
609.60
2101.42
609.60
5603.78
609.60
5603.78
609.60
1681.13
609.60
2521.70
609.60
1681.13
609.60
1681.13
609.60
609 60
3385.62
609.60
3385.62
609.60
1681.13
609.60
1681.13
609.60
2521.70
609.60
2521.70
609.60
5603.78
609.60
5603.78
609.60
2101.42
609.60
2101.42
609.60
5603.78
609.60
5603.78
609.60
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 19k
DEPTH
(m)
Soil
type
123.0
Clay
125.0
Clay
125.0
Sand
134.0
Sand
134.0
Clay
139.0
Clay
139.0
Clay
140.0
Clay
Q1
Z1
Q2
Z2
525.35
2.44
525.35
2.44
1400.94
2.44
1400.94
2.44
945.64
2.44
945.64
2.44
577.89
2.44
577.89
2.44
1050.71
15.85
1050.71
15.85
2801.89
15.85
2801.89
15.85
1891.28
15.85
1891.28
15.85
1155.78
15.85
1155.78
15.85
Q3
Z3
Q4
Q5
Z4
Z5
* Q (kN) Z (mm) *
1407.95
30.48
1407.95
30.48
3754.53
30.48
3754.53
30.48
2534.31
30.48
2534.31
30.48
1548.74
30.48
1548.74
30.48
1576.06
51.21
1576.06
51.21
4202.83
51.21
4202.83
51.21
2836.91
51.21
2836.91
51.21
1733.67
51.21
1733.67
51.21
1891.28
89.00
1891.28
89.00
5043.40
89.00
5043.40
89.00
3404.30
89.00
3404.30
89.00
2080.40
89.00
2080.40
89.00
Q6
Z6
Q7
Z7
2101.42
121.92
2101.42
121.92
5603.78
121.92
5603.78
121.92
3782.55
121.92
3782.55
121.92
2311.56
121.92
2311.56
121.92
2101.42
609.60
2101.42
609.60
5603.78
609.60
5603.78
609.60
3782.55
609.60
3782.55
609.60
2311.56
609.60
2311.56
609.60
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 19l
DEPTH
(m)
Soil
type
0.0
Silt
3.1
Silt
3.1
Clay
4.2
Clay
4.2
Silt
5.2
Silt
5.2
Clay
7.5
Clay
7.5
Silt
10.0
Silt
10.0
Clay
15.0
Clay
15.0
Clay
19.0
Clay
19.0
Clay
23.0
Clay
23.0
Clay
27.0
Clay
27.0
Clay
30.0
Clay
30.0
Silt
33.0
Silt
33.0
Clay
38.0
Clay
Q1
Z1
Q2
Z2
0.00
2.44
19.30
2.44
49.16
2.44
49.16
2.44
27.38
2.44
34.46
2.44
98.32
2.44
98.32
2.44
262.26
2.44
344.56
2.44
98.32
2.44
525.35
2 44
2.44
210.14
2.44
210.14
2.44
328.35
2.44
328.35
2.44
525.35
2.44
525.35
2.44
630.43
2.44
630.43
2.44
846.40
2.44
846.40
2.44
315.21
2.44
315.21
2.44
0.00
15.85
38.61
15.85
98.32
15.85
98.32
15.85
54.76
15.85
68.91
15.85
196.64
15.85
196.64
15.85
524.51
15.85
689.12
15.85
196.64
15.85
1050.71
15.85
15 85
420.28
15.85
420.28
15.85
656.69
15.85
656.69
15.85
1050.71
15.85
1050.71
15.85
1260.85
15.85
1260.85
15.85
1692.81
15.85
1692.81
15.85
630.43
15.85
630.43
15.85
Q3
Z3
Q4
Q5
Z4
Z5
* Q (kN) Z (mm) *
0.00
30.48
51.73
30.48
131.75
30.48
131.75
30.48
73.37
30.48
92.35
30.48
263.49
30.48
263.49
30.48
702.85
30.48
923.43
30.48
263.49
30.48
1407.95
30.48
30 48
563.18
30.48
563.18
30.48
879.97
30.48
879.97
30.48
1407.95
30.48
1407.95
30.48
1689.54
30.48
1689.54
30.48
2268.36
30.48
2268.36
30.48
844.77
30.48
844.77
30.48
0.00
51.21
57.91
51.21
147.48
51.21
147.48
51.21
82.14
51.21
103.37
51.21
294.96
51.21
294.96
51.21
786.77
51.21
1033.69
51.21
294.96
51.21
1576.06
51.21
51 21
630.43
51.21
630.43
51.21
985.04
51.21
985.04
51.21
1576.06
51.21
1576.06
51.21
1891.28
51.21
1891.28
51.21
2539.21
51.21
2539.21
51.21
945.64
51.21
945.64
51.21
0.00
89.00
69.49
89.00
176.97
89.00
176.97
89.00
98.56
89.00
124.05
89.00
353.95
89.00
353.95
89.00
944.12
89.00
1240.42
89.00
353.95
89.00
1891.28
89.00
89 00
756.51
89.00
756.51
89.00
1182.05
89.00
1182.05
89.00
1891.28
89.00
1891.28
89.00
2269.53
89.00
2269.53
89.00
3047.06
89.00
3047.06
89.00
1134.77
89.00
1134.77
89.00
Q6
Z6
Q7
Z7
0.00
121.92
77.21
121.92
196.64
121.92
196.64
121.92
109.51
121.92
137.83
121.92
393.27
121.92
393.27
121.92
1049.03
121.92
1378.25
121.92
393.27
121.92
2101.42
121.92
121 92
840.57
121.92
840.57
121.92
1313.39
121.92
1313.39
121.92
2101.42
121.92
2101.42
121.92
2521.70
121.92
2521.70
121.92
3385.62
121.92
3385.62
121.92
1260.85
121.92
1260.85
121.92
0.00
609.60
77.21
609.60
196.64
609.60
196.64
609.60
109.51
609.60
137.83
609.60
393.27
609.60
393.27
609.60
1049.03
609.60
1378.25
609.60
393.27
609.60
2101.42
609.60
609 60
840.57
609.60
840.57
609.60
1313.39
609.60
1313.39
609.60
2101.42
609.60
2101.42
609.60
2521.70
609.60
2521.70
609.60
3385.62
609.60
3385.62
609.60
1260.85
609.60
1260.85
609.60
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 19m
DEPTH
(m)
Soil
type
38.0
Silt
41.0
Silt
41.0
Clay
45.0
Clay
45.0
Silt
51.7
Silt
51.7
Clay
58.0
Clay
58.0
Clay
65.6
Clay
65.6
Sand
67.0
Sand
67.0
Silt
73.0
Silt
73.0
Silt
74.3
Silt
74.3
Clay
76.3
Clay
76.3
Silt
78.4
Silt
78.4
Clay
79.2
Clay
79.2
Silt
81.0
Silt
Q1
Z1
Q2
Z2
846.40
2.44
846.40
2.44
315.21
2.44
315.21
2.44
1400.94
2.44
1400.94
2.44
367.75
2.44
367.75
2.44
367.75
2.44
367.75
2.44
846.40
2.44
846.40
2 44
2.44
1400.94
2.44
1400.94
2.44
945.64
2.44
945.64
2.44
525.35
2.44
525.35
2.44
1400.94
2.44
1400.94
2.44
577.89
2.44
577.89
2.44
1400.94
2.44
1400.94
2.44
1692.81
15.85
1692.81
15.85
630.43
15.85
630.43
15.85
2801.89
15.85
2801.89
15.85
735.50
15.85
735.50
15.85
735.50
15.85
735.50
15.85
1692.81
15.85
1692.81
15.85
15 85
2801.89
15.85
2801.89
15.85
1891.28
15.85
1891.28
15.85
1050.71
15.85
1050.71
15.85
2801.89
15.85
2801.89
15.85
1155.78
15.85
1155.78
15.85
2801.89
15.85
2801.89
15.85
Q3
Z3
Q4
Q5
Z4
Z5
* Q (kN) Z (mm) *
2268.36
30.48
2268.36
30.48
844.77
30.48
844.77
30.48
3754.53
30.48
3754.53
30.48
985.56
30.48
985.56
30.48
985.56
30.48
985.56
30.48
2268.36
30.48
2268.36
30.48
30 48
3754.53
30.48
3754.53
30.48
2534.31
30.48
2534.31
30.48
1407.95
30.48
1407.95
30.48
3754.53
30.48
3754.53
30.48
1548.74
30.48
1548.74
30.48
3754.53
30.48
3754.53
30.48
2539.21
51.21
2539.21
51.21
945.64
51.21
945.64
51.21
4202.83
51.21
4202.83
51.21
1103.24
51.21
1103.24
51.21
1103.24
51.21
1103.24
51.21
2539.21
51.21
2539.21
51.21
51 21
4202.83
51.21
4202.83
51.21
2836.91
51.21
2836.91
51.21
1576.06
51.21
1576.06
51.21
4202.83
51.21
4202.83
51.21
1733.67
51.21
1733.67
51.21
4202.83
51.21
4202.83
51.21
3047.06
89.00
3047.06
89.00
1134.77
89.00
1134.77
89.00
5043.40
89.00
5043.40
89.00
1323.89
89.00
1323.89
89.00
1323.89
89.00
1323.89
89.00
3047.06
89.00
3047.06
89.00
89 00
5043.40
89.00
5043.40
89.00
3404.30
89.00
3404.30
89.00
1891.28
89.00
1891.28
89.00
5043.40
89.00
5043.40
89.00
2080.40
89.00
2080.40
89.00
5043.40
89.00
5043.40
89.00
Q6
Z6
Q7
Z7
3385.62
121.92
3385.62
121.92
1260.85
121.92
1260.85
121.92
5603.78
121.92
5603.78
121.92
1470.99
121.92
1470.99
121.92
1470.99
121.92
1470.99
121.92
3385.62
121.92
3385.62
121.92
121 92
5603.78
121.92
5603.78
121.92
3782.55
121.92
3782.55
121.92
2101.42
121.92
2101.42
121.92
5603.78
121.92
5603.78
121.92
2311.56
121.92
2311.56
121.92
5603.78
121.92
5603.78
121.92
3385.62
609.60
3385.62
609.60
1260.85
609.60
1260.85
609.60
5603.78
609.60
5603.78
609.60
1470.99
609.60
1470.99
609.60
1470.99
609.60
1470.99
609.60
3385.62
609.60
3385.62
609.60
609 60
5603.78
609.60
5603.78
609.60
3782.55
609.60
3782.55
609.60
2101.42
609.60
2101.42
609.60
5603.78
609.60
5603.78
609.60
2311.56
609.60
2311.56
609.60
5603.78
609.60
5603.78
609.60
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 19n
DEPTH
(m)
Soil
type
81.0
Sand
86.0
Sand
86.0
Silt
88.6
Silt
88.6
Clay
90.8
Clay
90.8
Silt
93.0
Silt
93.0
Clay
97.0
Clay
97.0
Clay
102.5
Clay
102.5
Silt
103.4
Silt
103.4
Clay
106.0
Clay
106.0
Clay
107.3
Clay
107.3
Sand
109.0
Sand
109.0
Clay
116.3
Clay
116.3
Sand
123.0
Sand
Q1
Z1
Q2
Z2
1400.94
2.44
1400.94
2.44
1400.94
2.44
1400.94
2.44
525.35
2.44
525.35
2.44
1400.94
2.44
1400.94
2.44
420.28
2.44
630.43
2.44
420.28
2.44
420.28
2 44
2.44
846.40
2.44
846.40
2.44
420.28
2.44
420.28
2.44
630.43
2.44
630.43
2.44
1400.94
2.44
1400.94
2.44
525.35
2.44
525.35
2.44
1400.94
2.44
1400.94
2.44
2801.89
15.85
2801.89
15.85
2801.89
15.85
2801.89
15.85
1050.71
15.85
1050.71
15.85
2801.89
15.85
2801.89
15.85
840.57
15.85
1260.85
15.85
840.57
15.85
840.57
15.85
15 85
1692.81
15.85
1692.81
15.85
840.57
15.85
840.57
15.85
1260.85
15.85
1260.85
15.85
2801.89
15.85
2801.89
15.85
1050.71
15.85
1050.71
15.85
2801.89
15.85
2801.89
15.85
Q3
Z3
Q4
Q5
Z4
Z5
* Q (kN) Z (mm) *
3754.53
30.48
3754.53
30.48
3754.53
30.48
3754.53
30.48
1407.95
30.48
1407.95
30.48
3754.53
30.48
3754.53
30.48
1126.36
30.48
1689.54
30.48
1126.36
30.48
1126.36
30.48
30 48
2268.36
30.48
2268.36
30.48
1126.36
30.48
1126.36
30.48
1689.54
30.48
1689.54
30.48
3754.53
30.48
3754.53
30.48
1407.95
30.48
1407.95
30.48
3754.53
30.48
3754.53
30.48
4202.83
51.21
4202.83
51.21
4202.83
51.21
4202.83
51.21
1576.06
51.21
1576.06
51.21
4202.83
51.21
4202.83
51.21
1260.85
51.21
1891.28
51.21
1260.85
51.21
1260.85
51.21
51 21
2539.21
51.21
2539.21
51.21
1260.85
51.21
1260.85
51.21
1891.28
51.21
1891.28
51.21
4202.83
51.21
4202.83
51.21
1576.06
51.21
1576.06
51.21
4202.83
51.21
4202.83
51.21
5043.40
89.00
5043.40
89.00
5043.40
89.00
5043.40
89.00
1891.28
89.00
1891.28
89.00
5043.40
89.00
5043.40
89.00
1513.02
89.00
2269.53
89.00
1513.02
89.00
1513.02
89.00
89 00
3047.06
89.00
3047.06
89.00
1513.02
89.00
1513.02
89.00
2269.53
89.00
2269.53
89.00
5043.40
89.00
5043.40
89.00
1891.28
89.00
1891.28
89.00
5043.40
89.00
5043.40
89.00
Q6
Z6
Q7
Z7
5603.78
121.92
5603.78
121.92
5603.78
121.92
5603.78
121.92
2101.42
121.92
2101.42
121.92
5603.78
121.92
5603.78
121.92
1681.13
121.92
2521.70
121.92
1681.13
121.92
1681.13
121.92
121 92
3385.62
121.92
3385.62
121.92
1681.13
121.92
1681.13
121.92
2521.70
121.92
2521.70
121.92
5603.78
121.92
5603.78
121.92
2101.42
121.92
2101.42
121.92
5603.78
121.92
5603.78
121.92
5603.78
609.60
5603.78
609.60
5603.78
609.60
5603.78
609.60
2101.42
609.60
2101.42
609.60
5603.78
609.60
5603.78
609.60
1681.13
609.60
2521.70
609.60
1681.13
609.60
1681.13
609.60
609 60
3385.62
609.60
3385.62
609.60
1681.13
609.60
1681.13
609.60
2521.70
609.60
2521.70
609.60
5603.78
609.60
5603.78
609.60
2101.42
609.60
2101.42
609.60
5603.78
609.60
5603.78
609.60
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 19o
DEPTH
(m)
Soil
type
123.0
Clay
125.0
Clay
125.0
Sand
134.0
Sand
134.0
Clay
139.0
Clay
139.0
Clay
140.0
Clay
Q1
Z1
Q2
Z2
525.35
2.44
525.35
2.44
1400.94
2.44
1400.94
2.44
945.64
2.44
945.64
2.44
577.89
2.44
577.89
2.44
1050.71
15.85
1050.71
15.85
2801.89
15.85
2801.89
15.85
1891.28
15.85
1891.28
15.85
1155.78
15.85
1155.78
15.85
Q3
Z3
Q4
Q5
Z4
Z5
* Q (kN) Z (mm) *
1407.95
30.48
1407.95
30.48
3754.53
30.48
3754.53
30.48
2534.31
30.48
2534.31
30.48
1548.74
30.48
1548.74
30.48
1576.06
51.21
1576.06
51.21
4202.83
51.21
4202.83
51.21
2836.91
51.21
2836.91
51.21
1733.67
51.21
1733.67
51.21
1891.28
89.00
1891.28
89.00
5043.40
89.00
5043.40
89.00
3404.30
89.00
3404.30
89.00
2080.40
89.00
2080.40
89.00
Q6
Z6
Q7
Z7
2101.42
121.92
2101.42
121.92
5603.78
121.92
5603.78
121.92
3782.55
121.92
3782.55
121.92
2311.56
121.92
2311.56
121.92
2101.42
609.60
2101.42
609.60
5603.78
609.60
5603.78
609.60
3782.55
609.60
3782.55
609.60
2311.56
609.60
2311.56
609.60
Date Performed
10/06/2013
Made by
SP
Checked by
CHG
Plate 19p
50
100
150
200
250
300
350
400
10
20
30
40
50
60
70
80
90
100
110
120
130
140
qc/300
Date performed:
BH SV-6X
BLOCK 15-1
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
PGS/SI/2013/CLJOC/06/SV-6X/FR
10/06/2013
Made by
SP
Checked by
CHG
Plate 20
Stratum
Soil Description
Penetration
(m)
From
Medium dense
silty fine SAND
Stiff to very stiff
lean CLAY
Medium dense
silty fine SAND
Very stiff
sandy lean CLAY
Medium dense
SILT with sand
0.0
Very stiff
lean CLAY
10.0
Stiff
sandy lean CLAY
15.0
19.0
Very stiff
lean CLAY
23.0
Hard
fat CLAY
Medium dense
clayey
l
SILT
27.0
1
2
3
4
5
10
11
3.1
4.2
4.2
5.2
5.2
7.5
7.5
10.0
15.0
19.0
23.0
27.0
30.0
30.0
33 0
33.0
Very stiff
silty CLAY
33.0
13
Medium dense
SILT
38.0
14
Very stiff
lean CLAY with sand
41.0
Dense
sandy SILT
Stiff to very stiff
lean CLAY
45.0
15
16
17
18
19
20
38.0
41.0
45.0
51.7
51.7
58.0
Very stiff
lean CLAY
58.0
Medium dense
silty fine SAND
Dense
sandy SILT
Hard
cohesive SILT
65.6
Setup
Factor
To
3.1
12
Sur (kPa)
26.7
26.7
11.1
12.1
26.7
26.7
21.5
23.5
26.7
26.7
25.1
27.8
16.3
18.4
23.0
25.5
32.3
35.1
38.4
40.5
43.3
43.3
43 3
30.1
32.3
36.7
36.7
33.7
35.5
43.3
43.3
41.1
42.0
73.0
42.0
42.0
46.7
46.7
80.0
80.0
74.3
77.7
78.4
65.6
67.0
67.0
73.0
Cone
k Factor Resistance
(MPa)
1.0
0.5
8.00
0.15
1.0
0.5
8.00
0.15
1.0
0.5
8.00
0.15
0.15
0.15
0.15
0.15
1.0
0.5
13.00
0.15
1.0
0.5
11.00
0.15
1.0
0.7
13.00
0.15
0.15
1.0
0.5
14.00
1.0
0.7
24.00
0.15
Date Performed
28/06/2013
Made by
SP
Checked by
CHG
:
Plate 21a
Stratum
Soil Description
Penetration
(m)
From
21
74.3
22
Dense
sandy SILT
76.3
23
78.4
Dense
SILT
Dense
silty fine SAND
Dense
SILT
79.2
27
Very stiff
lean CLAY with sand
88.6
28
Dense
SILT
90.8
29
93.0
30
Very stiff
lean CLAY
97.0
31
Medium dense
SILT
102.5
32
Very stiff
lean CLAY
103.4
33
106.0
34
Dense
SILT
107.3
35
109.0
36
Dense
silty fine SAND
116.3
37
123.0
Dense
silty fine SAND
Hard
sandy lean CLAY
125.0
24
25
26
38
39
40
Sur (kPa)
Setup
Factor
To
76.3
78.4
79.2
81.0
81.0
86.0
86.0
88.6
90.8
93.0
97.0
102.5
103
103.4
4
106.0
107.3
109.0
116.3
123.0
58.4
59.1
70.0
70.9
62.9
63.2
70.0
70.0
43.3
43.3
86.7
86.7
60.0
60.0
70.0
70.0
48.0
72.0
48.0
48.0
43.3
43
43.3
3
48.0
48.0
72.0
72.0
83.3
83.3
60.0
60.0
70.0
70.0
139.0
60.0
60.0
96.7
96.7
104.7
106.7
140.0
66.0
66.0
125.0
134.0
134.0
139.0
Cone
k Factor Resistance
(MPa)
0.15
1.0
0.7
13.00
0.15
1.0
0.7
21.00
1.0
0.7
13.00
1.0
0.7
26.00
0.15
1.0
0.7
21.00
0.15
0.15
1.0
0.5
13.00
0.15
0.15
1.0
0.7
25.00
0.15
1.0
0.7
24.00
0.15
1.0
0.7
29.00
0.15
0.15
Date Performed
28/06/2013
Made by
SP
Checked by
CHG
:
Plate 21b
10
20
30
40
50
60
70
80
90
100
10
20
30
40
50
60
70
80
90
Upper Bound
100
110
Date performed:
12/06/2013
Made by
SP
Checked by
CHG
Prepared by
:
Plate 22a
10
20
30
40
50
60
70
80
90
100
10
20
30
40
50
60
70
80
90
Upper Bound
100
110
Date performed:
12/06/2013
Made by
SP
Checked by
CHG
Prepared by
:
Plate 22b
10
20
30
40
50
60
70
80
90
100
10
20
30
40
50
60
70
80
90
Upper Bound
100
110
Date performed:
12/06/2013
Made by
SP
Checked by
CHG
Prepared by
:
Plate 22c
10
20
30
40
50
60
70
80
90
100
10
20
30
40
50
60
70
80
90
Upper Bound
100
110
Date performed:
12/06/2013
Made by
SP
Checked by
CHG
Prepared by
:
Plate 22d
Rated
Energy
(kNm)
Ram
Weight
(kN)
IHC S280
278.40
133.77
IHC S750
746.87
369.84
Cushion
Area
(kN)
Elastic
Modulus
(MPa)
15.70
Helmet Weight
36.16
(cm )
Coefficient of
Restitution
Hammer
Efficiency
(%)
0.8
90
Silt
Sand
Soil Data
Parameter
Clay
Soft
Stiff
Very Stiff
Hard
Shaft
0.361
0.197
0.164
0.098
0.230
0.262
Toe
0.656
0.492
0.492
0.492
0.492
0.492
Clay
Silt
Sand
Shaft
2.54
2.54
2.54
Toe
2.54
2.54
2.54
Damping
(sec/m)
Parameter
Quake (mm)
Date performed:
17/06/2013
Made by
SP
Checked by
CHG
Prepared by
:
Plate 23
24
22
20
18
(1)
14
12
10
16
Wall Thickness
= 25.4mm (1.0-inch)
= 194.1 m
0
50
100
150
200
250
300
350
Blowcounts (Blows/300mm)
Date performed:
14/06/2013
Made by
SP
Checked by
CHG
Plate 24a
24
22
20
18
(1)
14
12
10
16
Wall Thickness
= 25.4mm (1.0-inch)
= 194.1 m
0
50
100
150
200
250
300
350
Blowcounts (Blows/300mm)
Date performed:
14/06/2013
Made by
SP
Checked by
CHG
Plate 24b
40
36
(2)
32
28
24
20
16
(1)
12
4
Wall Thickness
= 38.1mm (1.5-inch)
= 194.1 m
0
50
100
150
200
250
300
350
Blowcounts (Blows/300mm)
Date performed:
14/06/2013
Made by
SP
Checked by
CHG
Plate 24c
40
36
32
(2)
28
24
20
16
(1)
12
4
Wall Thickness
= 38.1mm (1.5-inch)
= 194.1 m
0
50
100
150
200
250
300
350
Blowcounts (Blows/300mm)
Date performed:
14/06/2013
Made by
SP
Checked by
CHG
Plate 24d
60
54
(2)
48
(1)
36
30
24
42
18
12
6
Wall Thickness
= 50.0mm (1.97-inch)
Pile Penetration
= 140 m
Pile Length
= 194.1 m
0
50
100
150
200
250
300
350
Blowcounts (Blows/300mm)
Date performed:
14/06/2013
Made by
SP
Checked by
CHG
Plate 24e
60
54
(2)
48
(1)
36
30
24
42
18
12
6
Wall Thickness
= 50.0mm (1.97-inch)
Pile Penetration
= 140 m
Pile Length
= 194.1 m
0
50
100
150
200
250
300
350
Blowcounts (Blows/300mm)
Date performed:
14/06/2013
Made by
SP
Checked by
CHG
Plate 24f
60
(2)
54
48
42
36
30
24
(1)
18
12
6
Wall Thickness
= 50.0mm (2.362-inch)
Pile Penetration
= 140 m
Pile Length
= 194.1 m
0
50
100
150
200
250
300
350
Blowcounts (Blows/300mm)
Date performed:
14/06/2013
Made by
SP
Checked by
CHG
Plate 24g
60
(2)
54
48
42
36
30
24
(1)
18
12
6
Wall Thickness
= 60.0mm (2.362-inch)
Pile Penetration
= 140 m
Pile Length
= 194.1 m
0
50
100
150
200
250
300
350
Blowcounts (Blows/300mm)
Date performed:
14/06/2013
Made by
SP
Checked by
CHG
Plate 24h
50
100
150
200
250
300
350
20
30
40
50
70
80
100
110
120
130
140
Date performed:
PGS/SI/2013/CLJOC/06/SV-6X/FR
17/06/2013
Made by
SP
Checked by
CHG
Plate 25a
50
100
150
200
250
300
350
20
30
40
50
60
70
90
100
110
120
130
140
Date performed:
PGS/SI/2013/CLJOC/06/SV-6X/FR
17/06/2013
Made by
SP
Checked by
CHG
Plate 25b
50
100
150
200
250
300
350
20
30
40
50
60
70
80
90
110
120
130
140
Date performed:
PGS/SI/2013/CLJOC/06/SV-6X/FR
17/06/2013
Made by
SP
Checked by
CHG
Plate 25c
50
100
150
200
250
300
350
20
30
40
50
60
70
90
100
110
120
130
140
Date performed:
PGS/SI/2013/CLJOC/06/SV-6X/FR
17/06/2013
Made by
SP
Checked by
CHG
Plate 25d
50
100
150
200
250
300
350
20
30
40
50
60
70
80
90
100
120
140
Date performed:
PGS/SI/2013/CLJOC/06/SV-6X/FR
17/06/2013
Made by
SP
Checked by
CHG
Plate 25e
50
100
150
200
250
300
350
10
20
30
40
50
60
70
90
100
110
120
130
140
Date performed:
PGS/SI/2013/CLJOC/06/SV-6X/FR
17/06/2013
Made by
SP
Checked by
CHG
Plate 25f
50
100
150
200
250
300
350
10
20
30
40
50
60
70
80
90
100
120
130
140
Date performed:
PGS/SI/2013/CLJOC/06/SV-6X/FR
17/06/2013
Made by
SP
Checked by
CHG
Plate 25g
APPENDIX A
PLASTICITY CHART
F-C-73
50
Rev.: 6
coarse-grained soil:
40
30
MH or OH
Effective: 21-02-2012
20
Vertical at LL = 16 to PI = 7,
Tested By:
CL-ML
ML or OL
0
0
10
20
30
40
50
60
70
80
90
100
110
120
Sample Sample
Index Number
Sample
Depth, (m)
LL
(%)
PI
(%)
P4C
3.6
32
16
P5A
4.2
28
14
P6B
5.6
26
11
Sand
(%)
51.5
Silt
(%)
20.6
Clay
(%)
27.9
Group
Symbol
Plate ./
Gravel
(%)
CL
SC
CL
Very stiff brown sandy lean CLAY with few silt and traces of
organic pockets
Plate A1
PLASTICITY CHART
F-C-73
50
Rev.: 6
coarse-grained soil:
40
30
MH or OH
Effective: 21-02-2012
20
Vertical at LL = 16 to PI = 7,
Tested By:
CL-ML
ML or OL
0
0
10
20
30
40
50
60
70
80
90
100
110
120
Sample Sample
Index Number
Sample
Depth, (m)
LL
(%)
PI
(%)
Gravel
(%)
Sand
(%)
Silt
(%)
Clay
(%)
Group
Symbol
37.6
33.3
29.1
CL
Very stiff brown sandy lean CLAY with few silt and traces of
organic pockets
P7C
6.8
31
14
P8A
7.2
47
22
CL
Very stiff brown sandy lean CLAY with few silt and traces of
organic pockets
P12C
10.9
43
20
CL
Very stiff brown lean CLAY with few silt pockets traces of shell
fragments, organic and ferrous stains
Plate A2
Checked By:
Plate ./
PLASTICITY CHART
F-C-73
50
Rev.: 6
coarse-grained soil:
40
30
MH or OH
Effective: 21-02-2012
20
Vertical at LL = 16 to PI = 7,
Tested By:
CL-ML
ML or OL
0
0
10
20
30
40
50
60
70
80
90
100
110
120
Sample Sample
Index Number
Sample
Depth, (m)
LL
(%)
PI
(%)
P13C
11.7
46
23
P14C
12.8
38
17
P15B
13.6
37
16
Sand
(%)
19.8
Silt
(%)
38.7
Clay
(%)
41.5
Group
Symbol
CL
Very stiff brown lean CLAY with few silt pockets traces of shell
fragments, organic and ferrous stains
CL
Very stiff brown lean CLAY with sand with few silt pockets traces
of shell fragments, organic and ferrous stains
CL
Very stiff brown lean CLAY with few silt seams traces of shell
fragments, organic and ferrous stains
Checked By:
Plate ./
Gravel
(%)
Plate A3
PLASTICITY CHART
F-C-73
50
Rev.: 6
coarse-grained soil:
40
30
MH or OH
Effective: 21-02-2012
20
Vertical at LL = 16 to PI = 7,
Tested By:
CL-ML
ML or OL
0
0
10
20
30
40
50
60
70
80
90
100
110
120
Sample Sample
Index Number
Sample
Depth, (m)
LL
(%)
PI
(%)
Gravel
(%)
Sand
(%)
Silt
(%)
Clay
(%)
Group
Symbol
P16C
14.2
40
18
CL
Very stiff brown lean CLAY with few silt pockets traces of shell
fragments, organic and ferrous stains
P17B
15.4
34
13
CL
Firm light brown lean CLAY with few sand and silt pockets,
traces of shell fragments
P18C
16.8
35
17
CL
Very stiff light brownish gray sandy lean CLAY with fine to
coarse gravel
Plate A4
Checked By:
Plate ./
PLASTICITY CHART
F-C-73
50
Rev.: 6
coarse-grained soil:
40
30
MH or OH
Effective: 21-02-2012
20
Vertical at LL = 16 to PI = 7,
Tested By:
CL-ML
ML or OL
0
0
10
20
30
40
50
60
70
80
90
100
110
120
Sample Sample
Index Number
Sample
Depth, (m)
LL
(%)
PI
(%)
Gravel
(%)
Sand
(%)
Silt
(%)
Clay
(%)
Group
Symbol
26.7
40.9
20.3
12.1
CL
Stiff light brownish gray sandy lean CLAY with fine to coarse
gravel
P19C
17.6
25
10
P20B
18.6
25
11
CL
Stiff light brownish gray sandy lean CLAY with fine to coarse
gravel
P21B
19.4
35
18
CL
Very stiff brown sandy lean CLAY with few cemented silt and
traces of silt pockets
Plate A5
Checked By:
Plate ./
PLASTICITY CHART
F-C-73
50
Rev.: 6
coarse-grained soil:
40
30
MH or OH
Effective: 21-02-2012
20
Vertical at LL = 16 to PI = 7,
Tested By:
CL-ML
ML or OL
0
0
10
20
30
40
50
60
70
80
90
100
110
120
Sample Sample
Index Number
Sample
Depth, (m)
LL
(%)
PI
(%)
P23B
21.6
29
10
P25B
23.4
48
26
P27C
25.6
33
15
Sand
(%)
Silt
(%)
Clay
(%)
Group
Symbol
35.2
35.4
29.4
CL
Very stiff brown sandy lean CLAY with few cemented silt and
traces of silt pockets
CL
Very stiff yellowish brown lean CLAY with sand with traces of
shell fragments and silt pockets
CL
Very stiff yellowish brown lean CLAY with sand with traces of
shell fragments and silt pockets
27.5
44.3
28.2
Plate A6
Checked By:
Plate ./
Gravel
(%)
PLASTICITY CHART
F-C-73
50
Rev.: 6
coarse-grained soil:
40
30
MH or OH
Effective: 21-02-2012
20
Vertical at LL = 16 to PI = 7,
Tested By:
CL-ML
ML or OL
0
0
10
20
30
40
50
60
70
80
90
100
110
120
Sample Sample
Index Number
Sample
Depth, (m)
LL
(%)
PI
(%)
Gravel
(%)
Sand
(%)
Silt
(%)
Clay
(%)
P28B
26.6
35
16
P30B
28.4
60
34
2.4
37.6
60.0
P32B
33.6
26
12.8
63.0
24.2
CL
Very stiff yellowish brown lean CLAY with sand with traces of
shell fragments and silt pockets
CH
CL-ML Medium dense yellowish brown silty CLAY with traces of shell
fragments pockets
Plate A7
Checked By:
Plate ./
Group
Symbol
PLASTICITY CHART
F-C-73
50
Rev.: 6
coarse-grained soil:
40
30
MH or OH
Effective: 21-02-2012
20
Vertical at LL = 16 to PI = 7,
Tested By:
CL-ML
ML or OL
0
0
10
20
30
40
50
60
70
80
90
100
110
120
Sample Sample
Index Number
Sample
Depth, (m)
LL
(%)
PI
(%)
Gravel
(%)
Silt
(%)
Clay
(%)
Group
Symbol
Plate ./
P33B
37.6
26
32.9
48.3
18.8
CL-ML
P34B
41.4
33
15
26.1
57.5
16.4
CL
Very stiff yellowish brown lean CLAY with sand with traces of
shell fragments
P37A
53.2
36
17
19.2
55.3
25.5
CL
Stiff dark yellowish brown lean CLAY with few sand seams and
cemented silt pockets
Plate A8
Checked By:
Sand
(%)
PLASTICITY CHART
F-C-73
50
Rev.: 6
coarse-grained soil:
40
30
MH or OH
Effective: 21-02-2012
20
Vertical at LL = 16 to PI = 7,
Tested By:
CL-ML
ML or OL
0
0
10
20
30
40
50
60
70
80
90
100
110
120
Sample Sample
Index Number
Sample
Depth, (m)
LL
(%)
PI
(%)
Gravel
(%)
Sand
(%)
Silt
(%)
P38AR
57.4
37
17
P39B
61.7
47
23
1.7
60.4
P42B
73.5
28
7.6
81.5
Group
Symbol
CL
Stiff dark yellowish brown lean CLAY with few sand seams and
cemented silt pockets
37.9
CL
Very stiff dark greenish gray lean CLAY with few shell fragments
and traces of silt pockets
10.9
ML
Olive brown SILT with traces of shell framgents and mica specks
Plate A9
Checked By:
Plate ./
Clay
(%)
PLASTICITY CHART
F-C-73
50
Rev.: 6
coarse-grained soil:
40
30
MH or OH
Effective: 21-02-2012
20
Vertical at LL = 16 to PI = 7,
Tested By:
CL-ML
ML or OL
0
0
10
20
30
40
50
60
70
80
90
100
110
120
Sample Sample
Index Number
Sample
Depth, (m)
LL
(%)
PI
(%)
P43A
77.4
P44C
81.9
34
15
P46CR
89.8
30
10
NP
Sand
(%)
Silt
(%)
Clay
(%)
Group
Symbol
45.4
42.2
12.4
ML
CL
Very stiff olive brown lean CLAY with few silt pockets
CL
Very stiff greenish gray lean CLAY with sand with traces of silt
pockets and shell fragments
14.9
67.5
17.6
Plate A10
Checked By:
Plate ./
Gravel
(%)
PLASTICITY CHART
F-C-73
50
Rev.: 6
coarse-grained soil:
40
30
MH or OH
Effective: 21-02-2012
20
Vertical at LL = 16 to PI = 7,
Tested By:
CL-ML
ML or OL
0
0
10
20
30
40
50
60
70
80
90
100
110
120
Sample Sample
Index Number
Sample
Depth, (m)
LL
(%)
PI
(%)
Gravel
(%)
Sand
(%)
Silt
(%)
Clay
(%)
Group
Symbol
P47C
93.8
33
13
5.5
53.3
41.2
CL
Very stiff greenish gray lean CLAY with traces of shel fragments
P48C
97.8
39
17
5.2
51.5
43.3
CL
Very stiff dark greenish gray lean CLAY with traces of silt and
organic pockets and shell fragments
P49B
101.6
36
16
7.9
43.6
48.5
CL
Very stiff dark greenish gray lean CLAY with traces of silt and
organic pockets and shell fragments
Plate A11
Checked By:
Plate ./
PLASTICITY CHART
F-C-73
50
Rev.: 6
coarse-grained soil:
40
30
MH or OH
Effective: 21-02-2012
20
Vertical at LL = 16 to PI = 7,
Tested By:
CL-ML
ML or OL
0
0
10
20
30
40
50
60
70
80
90
100
110
120
Sample Sample
Index Number
Sample
Depth, (m)
LL
(%)
PI
(%)
P50B
105.6
31
12
P51C
109.8
41
20
P52B
113.6
27
Sand
(%)
Silt
(%)
Clay
(%)
Group
Symbol
11.5
38.2
50.3
CL
Very stiff dark greenish gray lean CLAY with traces of silt and
organic pockets and shell fragments
CL
Very stiff dark greenish gray lean CLAY with few silt pockets and
traces of shell fragments
CL
Very stiff dark greenish gray lean CLAY with sand with few silt
pockets and traces of shell fragments
18.0
42.3
39.7
Plate A12
Checked By:
Plate ./
Gravel
(%)
PLASTICITY CHART
F-C-73
50
Rev.: 6
coarse-grained soil:
40
30
MH or OH
Effective: 21-02-2012
20
Vertical at LL = 16 to PI = 7,
Tested By:
CL-ML
ML or OL
0
0
10
20
30
40
50
60
70
80
90
100
110
120
Sample Sample
Index Number
P58B
LL
(%)
PI
(%)
Gravel
(%)
Sand
(%)
Silt
(%)
Clay
(%)
Group
Symbol
136.5
30
12
0.0
37.9
35.7
26.4
CL
Plate ./
#N/A #N/A
#N/A #N/A
Plate A13
Checked By:
Sample
Depth, (m)
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
FINE
19
4.75
0.4
Cumulative Per.
Plate ./
P1B
COARSE
100.0
MEDIUM
2.0
3.0
99.6
FINE-GRAINED SOIL
FINE
0.425
13.3
96.6
SILT
CLAY
0.075
57.2
0.005
14.0
83.3
3.3
26.1
Cu =
15.3
0.002
12.1
Cc =
4.9
8.8
8.8
Check by:
Sample No:
SAND
Soil Description: Calcareous medium dense dark greenish gray silty fine SAND with few to some shell fragments
Plate A14
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
FINE
19
4.75
4.3
Cumulative Per.
Plate ./
P2A
COARSE
100.0
MEDIUM
2.0
3.8
95.7
FINE-GRAINED SOIL
FINE
0.425
8.3
91.9
SILT
CLAY
0.075
64.2
0.005
9.1
83.6
1.5
19.4
Cu =
58.5
0.002
10.3
Cc =
8.8
8.8
18.8
Soil Description: Calcareous medium dense dark greenish gray silty fine SAND with few to some shell fragments
Plate A15
Check by:
Sample No:
SAND
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
2.8
Cumulative Per.
P3C
FINE
CLAY
0.075
51.1
0.005
17.0
97.2
3.6
46.1
Cu =
29.1
0.002
25.5
25.5
Cc =
Soil Description: Medium dense reddish brown silty fine SAND with few clay pockets
Plate A16
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
1.6
Cumulative Per.
P5A
FINE
CLAY
0.075
49.9
0.005
20.6
98.4
4.3
48.5
Cu =
15.3
27.9
Cc =
0.002
23.6
23.6
4.9
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
0.7
Cumulative Per.
P5C
FINE
CLAY
0.075
67.2
0.005
16.3
99.3
3.4
32.1
Cu =
15.8
0.002
12.4
12.4
Cc =
Soil Description: Medium dense dark yellowish brown silty fine SAND
Plate A18
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
1.5
Cumulative Per.
P7C
FINE
CLAY
0.075
36.1
0.005
33.3
98.5
6.4
62.4
Cu =
29.1
0.002
22.7
22.7
Cc =
Soil Description: Very stiff brown sandy lean CLAY with few silt and traces of organic pockets
Plate A19
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
1.2
Cumulative Per.
P9C
FINE
CLAY
0.075
39.7
0.005
50.3
98.8
4.9
59.1
Cu =
13.1
0.002
8.8
Cc =
3.9
3.9
3.1
Soil Description: Medium dense yellowish brown none plasticity sandy SILT with traces cemented sand, clay and organic pockets
Plate A20
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
0.9
Cumulative Per.
P10B
FINE
CLAY
0.075
28.1
0.005
61.3
99.1
3.9
71.0
Cu =
12.3
0.002
9.7
Cc =
5.8
5.8
3.5
Soil Description: Medium dense yellowish brown none plasticity SILT with sand with traces cemented sand, clay and organic pockets
Plate A21
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
0.5
Cumulative Per.
P11B
FINE
CLAY
0.075
20.9
0.005
64.4
99.5
3.3
78.6
Cu =
37.7
14.2
Cc =
0.002
10.9
10.9
7.8
Soil Description: Medium dense yellowish brown none plasticity SILT with sand with traces cemented sand, clay and organic pockets
Plate A22
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
1.8
Cumulative Per.
P14C
FINE
CLAY
0.075
18.0
0.005
38.7
98.2
9.7
80.2
Cu =
41.5
0.002
31.8
31.8
Cc =
Soil Description: Very stiff brown lean CLAY with sand with few silt pockets traces of shell fragments, organic and ferrous stains
Plate A23
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
FINE
19
4.75
26.7
Cumulative Per.
Plate ./
P19C
COARSE
100.0
MEDIUM
2.0
4.9
73.3
FINE-GRAINED SOIL
FINE
0.425
3.9
68.4
SILT
CLAY
0.075
32.1
0.005
20.3
64.5
2.7
32.4
Cu =
86.7
0.002
12.1
Cc =
9.4
9.4
6.4
Soil Description: Stiff light brownish gray sandy lean CLAY with fine to coarse gravel
Plate A24
Check by:
Sample No:
SAND
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
0.4
Cumulative Per.
P23B
FINE
CLAY
0.075
34.8
0.005
35.4
99.6
4.2
64.8
Cu =
29.4
0.002
25.2
25.2
Cc =
Soil Description: Very stiff brown sandy lean CLAY eith few cemented silt and traces of silt pockets
Plate A25
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
1.3
Cumulative Per.
P27C
FINE
CLAY
0.075
26.2
0.005
44.3
98.7
4.3
72.5
Cu =
28.2
0.002
23.9
23.9
Cc =
Soil Description: Very stiff yellowish brown lean CLAY with sand with traces of shell fragments and silt pockets
Plate A26
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
1.0
Cumulative Per.
P30B
FINE
CLAY
0.075
1.4
0.005
37.6
99.0
10.3
97.6
Cu =
60.0
0.002
49.7
49.7
Cc =
Soil Description: Hard brown fat CLAY with few cemented silt pockets
Plate A27
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
FINE-GRAINED SOIL
MEDIUM
2.0
FINE
0.425
Plate ./
P32B
0.075
12.8
Cumulative Per.
33.6
0.005
63.0
100.0
Sample Depth, m Group Symbol: CL-ML
CLAY
6.0
87.2
Cu =
24.2
0.002
18.2
18.2
Cc =
Soil Description: Medium dense yellowish brown silty CLAY with traces of shell fragments pockets
Plate A28
Check by:
Sample No:
SILT
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
3.4
Cumulative Per.
P33B
FINE
CLAY
0.075
29.5
0.005
48.3
96.6
4.6
67.1
Cu =
18.8
0.002
14.2
14.2
Cc =
Soil Description: Very stiff yellowish brown sandy silty CLAY with traces of shell fragments pockets
Plate A29
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
5.0
Cumulative Per.
P34B
FINE
CLAY
0.075
21.1
0.005
57.5
95.0
5.2
73.9
Cu =
32.7
16.4
Cc =
0.002
11.2
11.2
2.4
Soil Description: Very stiff yellowish brown lean CLAY with sand with traces of shell fragments
Plate A30
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
5.7
Cumulative Per.
P35A
FINE
CLAY
0.075
27.9
0.005
59.1
94.3
3.7
66.4
Cu =
8.1
0.002
7.3
Cc =
3.6
3.6
1.9
Soil Description: Medium dense yellowish brown sandy SILT with few cemented silt and traces of shell fragments pockets
Plate A31
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
3.6
Cumulative Per.
P36C
FINE
CLAY
0.075
66.5
0.005
15.7
96.4
3.3
29.9
Cu =
165.2
14.2
Cc =
0.002
10.9
10.9
25.1
Soil Description: Medium dense yellowish brown silty fine SAND with traces to few clay partings
Plate A32
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
FINE-GRAINED SOIL
MEDIUM
2.0
FINE
0.425
Plate ./
P37A
0.075
19.2
Cumulative Per.
53.2
0.005
55.3
100.0
Sample Depth, m Group Symbol: CL
CLAY
6.7
80.8
Cu =
25.5
0.002
18.8
18.8
Cc =
Soil Description: Stiff dark yellowish brown lean CLAY with few sand seams and cemented silt pockets
Plate A33
Check by:
Sample No:
SILT
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
FINE-GRAINED SOIL
MEDIUM
2.0
FINE
0.425
Plate ./
P39B
0.075
1.7
Cumulative Per.
61.7
0.005
60.4
100.0
Sample Depth, m Group Symbol: CL
CLAY
10.6
98.3
Cu =
37.9
0.002
27.3
27.3
Cc =
Soil Description: Very stiff dark greenish gray lean CLAY with few shell fragments and traces of silt pockets
Plate A34
Check by:
Sample No:
SILT
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
0.5
Cumulative Per.
P41B
FINE
CLAY
0.075
30.7
0.005
54.9
99.5
3.6
68.8
Cu =
152.1
13.9
Cc =
0.002
10.3
10.3
2.5
Soil Description: Medium dense olive brown sandy SILT with traces of shell fragments and mica specks
Plate A35
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
FINE-GRAINED SOIL
MEDIUM
2.0
FINE
0.425
Plate ./
P42B
0.075
7.6
Cumulative Per.
73.5
0.005
81.5
100.0
Sample Depth, m Group Symbol: ML
CLAY
4.2
92.4
Cu =
10.1
0.002
10.9
Cc =
6.7
6.7
2.4
Soil Description: Olive brown SILT with traces of shell framgents and mica specks
Plate A36
Check by:
Sample No:
SILT
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
0.7
Cumulative Per.
P43A
FINE
CLAY
0.075
44.7
0.005
42.2
99.3
3.3
54.6
Cu =
27.4
0.002
12.4
Cc =
9.1
9.1
5.4
Soil Description: Dense olive brown none plasticity sandy SILT with traces of cemented sand pockets
Plate A37
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
3.3
Cumulative Per.
P44A
FINE
CLAY
0.075
62.3
0.005
26.8
96.7
2.4
34.4
Cu =
11.8
0.002
7.6
Cc =
5.2
5.2
5.5
Soil Description: Medium dense dark greenish gray silty fine SAND with few shell fragments and traces of clay pockets
Plate A38
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
3.2
Cumulative Per.
P45B
FINE
CLAY
0.075
55.4
0.005
26.9
96.8
3.9
41.4
Cu =
78.0
14.5
Cc =
0.002
10.6
10.6
11.2
Soil Description: Medium dense dark greenish gray silty fine SAND with few shell fragments and traces of clay pockets
Plate A39
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
FINE-GRAINED SOIL
MEDIUM
2.0
FINE
0.425
Plate ./
P46CR
0.075
14.9
Cumulative Per.
89.8
0.005
67.5
100.0
Sample Depth, m Group Symbol: CL
CLAY
4.3
85.1
Cu =
17.6
0.002
13.3
13.3
Cc =
Soil Description: Very stiff greenish gray lean CLAY with sand with traces of silt pockets and shell fragments
Plate A40
Check by:
Sample No:
SILT
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
FINE-GRAINED SOIL
MEDIUM
2.0
FINE
0.425
Plate ./
P47C
0.075
5.5
Cumulative Per.
93.8
0.005
53.3
100.0
Sample Depth, m Group Symbol: CL
CLAY
10.3
94.5
Cu =
41.2
0.002
30.9
30.9
Cc =
Soil Description: Very stiff greenish gray lean CLAY with traces of shel fragments
Plate A41
Check by:
Sample No:
SILT
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
0.9
Cumulative Per.
P48C
FINE
CLAY
0.075
4.3
0.005
51.5
99.1
11.2
94.8
Cu =
43.3
0.002
32.1
32.1
Cc =
Soil Description: Very stiff dark greenish gray lean CLAY with traces of silt and organic pockets and shell fragments
Plate A42
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
1.9
Cumulative Per.
P49B
FINE
CLAY
0.075
6.0
0.005
43.6
98.1
9.7
92.1
Cu =
48.5
Cc =
0.002
38.8
38.8
Check by:
Sample No:
FINE-GRAINED SOIL
Soil Description: Very stiff dark greenish gray lean CLAY with traces of silt and organic pockets and shell fragments
Plate A43
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
0.6
Cumulative Per.
P50B
FINE
CLAY
0.075
10.9
0.005
38.2
99.4
10.6
88.5
Cu =
50.3
0.002
39.7
39.7
Cc =
Soil Description: Very stiff dark greenish gray lean CLAY with traces of silt and organic pockets and shell fragments
Plate A44
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
1.9
Cumulative Per.
P52B
FINE
CLAY
0.075
16.1
0.005
42.3
98.1
7.0
82.0
Cu =
39.7
0.002
32.7
32.7
Cc =
Soil Description: Very stiff dark greenish gray lean CLAY with sand with few silt pockets and traces of shell fragments
Plate A45
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
14.3
Cumulative Per.
P53B
FINE
CLAY
0.075
44.0
0.005
17.8
85.7
3.3
41.7
Cu =
23.9
0.002
20.6
20.6
Cc =
Soil Description: Medium dense dark gray silty fine SAND with few cemented sand and traces of clay pockets
Plate A46
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
2.4
Cumulative Per.
P54B
FINE
CLAY
0.075
91.7
0.005
5.0
97.6
0.3
5.9
Cu =
0.9
1.7
0.002
Cc =
0.6
0.6
0.9
Soil Description: Medium dense dark gray poorly graded fine SAND with traces of shell fragments
Plate A47
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
FINE
19
4.75
1.5
Cumulative Per.
Plate ./
P55B
COARSE
100.0
MEDIUM
2.0
5.9
98.5
FINE-GRAINED SOIL
FINE
0.425
26.6
92.6
SILT
CLAY
0.075
44.7
0.005
11.3
66.0
1.5
21.3
Cu =
66.8
0.002
10.0
Cc =
8.5
8.5
8.5
Soil Description: Medium dense dark gray silty fine SAND with some shell fragments
Plate A48
Check by:
Sample No:
SAND
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
9.7
Cumulative Per.
P56C
FINE
CLAY
0.075
57.4
0.005
15.0
90.3
4.3
32.9
Cu =
17.9
0.002
13.6
13.6
Cc =
Soil Description: Medium dense dark gray silty fine SAND with some shell fragments with traces of clay pockets
Plate A49
Check by:
Sample No:
FINE-GRAINED SOIL
Borehole: SV-6X
75
100
19
4,75
2,0
0,425
0,075
0,005
0,002
Rev.: 6
Percent Passing
80
60
50
40
0
100
10
0.1
0.01
0.001
Tested by:
Effective: 21-02-2012
20
GRAVEL
SUB-SOIL GR.
COARSE
SAND
FINE
19
COARSE
4.75
MEDIUM
2.0
100.0
Plate ./
SILT
0.425
5.4
Cumulative Per.
P58B
FINE
CLAY
0.075
32.5
0.005
35.7
94.6
5.8
62.1
Cu =
26.4
0.002
20.6
20.6
Cc =
Soil Description: Very stiff dark greenish gray sandy lean CLAY with little sand pockets, few shell fragments, and traces cemented sa
Plate A50
Check by:
Sample No:
FINE-GRAINED SOIL
600
560
520
480
440
400
360
320
4
280
240
200
2
160
120
80
40
0
0
10
12
14
16
18
20
P4
Depth (m)
3.6
14
21.6
Confining
pressure (kPa)
578
Su (kPa)
180
(%)
1.4
Strain,
50
PGS/SI/2013/CLJOC/06/SV-6X/FR
UNCONSOLIDATED UNDRAINED
TRIAXIAL COMPRESSION TEST
(ASTM : D 2850)
Location of Test :
Offshore
Type of Sample :
Undisturbed
Soil Type
CLAY
BH SV-6X
BLOCK 15/01
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
Plate A51
600
560
520
480
3
440
400
360
320
280
4
240
200
160
120
80
40
0
0
10
12
14
16
18
20
P8
Depth (m)
7.2
23
2319.1
Confining
pressure (kPa)
647
Su (kPa)
225
(%)
1.6
Strain,
50
PGS/SI/2013/CLJOC/06/SV-6X/FR
UNCONSOLIDATED UNDRAINED
TRIAXIAL COMPRESSION TEST
(ASTM : D 2850)
Location of Test :
Offshore
Type of Sample :
Undisturbed
Soil Type
CLAY
BH SV-6X
BLOCK 15/01
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
Plate A52
600
560
520
480
440
400
360
1
320
280
240
2
200
160
120
80
40
0
0
10
12
14
16
18
20
P15
Depth (m)
13.6
24
20.0
Confining
pressure (kPa)
768
Su (kPa)
178
(%)
1.4
Strain,
50
PGS/SI/2013/CLJOC/06/SV-6X/FR
UNCONSOLIDATED UNDRAINED
TRIAXIAL COMPRESSION TEST
(ASTM : D 2850)
Location of Test :
Offshore
Type of Sample :
Undisturbed
Soil Type
CLAY
BH SV-6X
BLOCK 15/01
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
Plate A53
600
560
520
480
440
400
360
320
280
240
200
1
160
120
80
40
0
0
10
12
14
16
18
20
P19
Depth (m)
17.2
16
19.9
Confining
pressure (kPa)
837
Su (kPa)
97
(%)
1.6
Strain,
50
PGS/SI/2013/CLJOC/06/SV-6X/FR
UNCONSOLIDATED UNDRAINED
TRIAXIAL COMPRESSION TEST
(ASTM : D 2850)
Location of Test :
Offshore
Type of Sample :
Undisturbed
Soil Type
CLAY
BH SV-6X
BLOCK 15/01
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
Plate A54
600
560
520
480
440
400
360
320
280
240
200
160
120
80
40
0
0
10
12
14
16
18
20
P23
Depth (m)
21.6
18
20.9
Confining
pressure (kPa)
920
Su (kPa)
102
(%)
1.4
Strain,
50
PGS/SI/2013/CLJOC/06/SV-6X/FR
UNCONSOLIDATED UNDRAINED
TRIAXIAL COMPRESSION TEST
(ASTM : D 2850)
Location of Test :
Offshore
Type of Sample :
Undisturbed
Soil Type
CLAY
BH SV-6X
BLOCK 15/01
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
Plate A55
600
560
520
480
440
400
360
320
280
240
200
160
120
80
40
0
0
10
12
14
16
18
20
P27
Depth (m)
25.6
20
20.9
Confining
pressure (kPa)
996
Su (kPa)
140
(%)
1.4
Strain,
50
PGS/SI/2013/CLJOC/06/SV-6X/FR
UNCONSOLIDATED UNDRAINED
TRIAXIAL COMPRESSION TEST
(ASTM : D 2850)
Location of Test :
Offshore
Type of Sample :
Undisturbed
Soil Type
CLAY
BH SV-6X
BLOCK 15/01
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
Plate A56
600
560
520
480
440
400
360
320
280
240
200
160
2
4
120
80
40
0
0
10
12
14
16
18
20
P31
Depth (m)
30.0
21
19.9
Confining
pressure (kPa)
1076
Su (kPa)
272
(%)
1.3
Strain,
50
PGS/SI/2013/CLJOC/06/SV-6X/FR
UNCONSOLIDATED UNDRAINED
TRIAXIAL COMPRESSION TEST
(ASTM : D 2850)
Location of Test :
Offshore
Type of Sample :
Undisturbed
Soil Type
CLAY
BH SV-6X
BLOCK 15/01
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
Plate A57
600
560
520
480
440
400
360
320
280
2
4
240
200
160
120
1
80
40
0
0
10
12
14
16
18
20
P37
Depth (m)
53.2
28
19.8
Confining
pressure (kPa)
1521
Su (kPa)
54
(%)
2.6
Strain,
50
PGS/SI/2013/CLJOC/06/SV-6X/FR
UNCONSOLIDATED UNDRAINED
TRIAXIAL COMPRESSION TEST
(ASTM : D 2850)
Location of Test :
Offshore
Type of Sample :
Undisturbed
Soil Type
CLAY
BH SV-6X
BLOCK 15/01
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
Plate A58
300
280
260
240
220
200
180
160
140
120
100
80
60
40
20
0
0
10
12
14
16
18
20
P42
Depth (m)
73.5
30
19.7
Confining
pressure (kPa)
1907
Su (kPa)
80
(%)
4.4
Strain,
50
PGS/SI/2013/CLJOC/06/SV-6X/FR
UNCONSOLIDATED UNDRAINED
TRIAXIAL COMPRESSION TEST
(ASTM : D 2850)
Location of Test :
Offshore
Type of Sample :
Undisturbed
Soil Type
CLAY
BH SV-6X
BLOCK 15/01
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
Plate A59
600
560
520
480
2
440
400
360
320
280
240
200
160
1
120
80
40
0
0
10
12
14
16
18
20
P47
Depth (m)
93.8
28
19.1
Confining
pressure (kPa)
2292
Su (kPa)
72
(%)
7.0
Strain,
50
PGS/SI/2013/CLJOC/06/SV-6X/FR
UNCONSOLIDATED UNDRAINED
TRIAXIAL COMPRESSION TEST
(ASTM : D 2850)
Location of Test :
Offshore
Type of Sample :
Undisturbed
Soil Type
CLAY
BH SV-6X
BLOCK 15/01
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
Plate A60
600
560
520
480
440
400
360
320
3
1
280
240
200
160
120
80
40
0
0
10
12
14
16
18
20
P51
109.8
23
19.9
Confining
pressure (kPa)
2596
Su (kPa)
152
(%)
4.0
Strain,
50
PGS/SI/2013/CLJOC/06/SV-6X/FR
UNCONSOLIDATED UNDRAINED
TRIAXIAL COMPRESSION TEST
(ASTM : D 2850)
Location of Test :
Offshore
Type of Sample :
Undisturbed
Soil Type
CLAY
BH SV-6X
BLOCK 15/01
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
Plate A61
Made by:
Checked by:
200
180
160
140
120
100
80
60
40
20
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
3.4
575
189
95
3.74
15.0
Soil Description:
Stiff brown lean CLAY with few ferrous nodules
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A62
Made by:
Checked by:
200
180
160
140
120
100
80
60
40
20
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
15.6
575
170
85
0.81
14.2
Soil Description:
Firm light brown lean CLAY with few sand and silt pockets, traces of shell fragments
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate/ A63
Plate
Made by:
Checked by:
400
360
320
280
240
200
160
120
80
40
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
5.8
620
319
160
1.81
12.8
Soil Description:
Very stiff brown sandy lean CLAY with few silt and traces of organic pockets
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A64
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
10.7
713
292
146
0.96
8.6
Soil Description:
Very stiff brown lean CLAY with few silt pockets traces of shell fragments, organic and ferrous stains
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A65
Made by:
Checked by:
400
360
320
280
240
200
160
120
80
40
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
10.9
713
358
179
0.46
12.0
Soil Description:
Very stiff brown lean CLAY with few silt pockets traces of shell fragments, organic and ferrous stains
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A66
Made by:
Checked by:
500
450
400
350
300
250
200
150
100
50
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
12.6
749
432
216
1.31
4.3
Soil Description:
Hard brown lean CLAY with few silt pockets traces of shell fragments, organic and ferrous stains
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A67
Made by:
Checked by:
500
450
400
350
300
250
200
150
100
50
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
12.6
749
362
181
0.67
14.7
Soil Description:
Hard brown lean CLAY with few silt pockets traces of shell fragments, organic and ferrous stains
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A68
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
14.2
780
272
136
2.63
7.9
Soil Description:
Very stiff brown lean CLAY with few silt pockets traces of shell fragments, organic and ferrous stains
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A69
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
14.2
780
253
127
0.83
15.0
Soil Description:
Very stiff brown lean CLAY with few silt pockets traces of shell fragments, organic and ferrous stains
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate/ A70
Made by:
Checked by:
100
90
80
70
60
50
40
30
20
10
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
15.6
806
89
45
2.43
9.9
Soil Description:
Firm light brown lean CLAY with few sand and silt pockets, traces of shell fragments
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A71
Made by:
Checked by:
100
90
80
70
60
50
40
30
20
10
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
15.6
806
88
44
0.47
8.1
Soil Description:
Firm light brown lean CLAY with few sand and silt pockets, traces of shell fragments
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A72
Made by:
Checked by:
400
360
320
280
240
200
160
120
80
40
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
16.6
825
255
128
1.45
10.7
Soil Description:
Very stiff light brownish gray sandy lean CLAY with fine to coarse gravel
Notes:
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A73
Made by:
Checked by:
200
180
160
140
120
100
80
60
40
20
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
17.6
844
142
71
2.87
15.0
Soil Description:
Stiff light brownish gray sandy lean CLAY with fine to coarse gravel
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A74
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
21.8
924
202
101
2.74
15.0
Soil Description:
Very stiff brown sandy lean CLAY with few cemented silt and traces of silt pockets
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate/ A75
Plate
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
21.8
924
189
95
0.48
12.7
Soil Description:
0
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate/A76
Made by:
Checked by:
400
360
320
280
240
200
160
120
80
40
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
24.6
977
368
184
1.20
14.2
Soil Description:
Very stiff yellowish brown lean CLAY with sand with traces of shell fragments and silt pockets
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate/A77
Plate
Made by:
Checked by:
200
180
160
140
120
100
80
60
40
20
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
25.4
993
197
99
2.04
14.3
Soil Description:
Very stiff yellowish brown lean CLAY with sand with traces of shell fragments and silt pockets
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate/ A78
Plate
Made by:
Checked by:
200
180
160
140
120
100
80
60
40
20
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
25.6
993
191
96
0.78
10.0
Soil Description:
0
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A79
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
26.8
1019
220
110
1.79
15.0
Soil Description:
Very stiff yellowish brown lean CLAY with sand with traces of shell fragments and silt pockets
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate /A80
Plate
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
26.8
1019
205
103
0.73
15.0
Soil Description:
0
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate /A81
Plate
Made by:
Checked by:
700
630
560
490
420
350
280
210
140
70
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
28.2
1046
659
330
1.29
6.4
Soil Description:
Hard brown fat CLAY with few cemented silt pockets
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A82
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
37.8
1228
242
121
2.41
11.3
Soil Description:
Very stiff yellowish brown sandy silty CLAY with traces of shell fragments pockets
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A83
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
109.6
1228
167
84
0.46
15.0
Soil Description:
0
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A84
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
41.6
1300
251
126
3.09
14.8
Soil Description:
Very stiff yellowish brown lean CLAY with sand with traces of shell fragments
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A85
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
41.6
1300
243
122
0.99
13.7
Soil Description:
0
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A86
Made by:
Checked by:
200
180
160
140
120
100
80
60
40
20
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
53.6
1258
115
58
4.37
14.9
Soil Description:
Stiff dark yellowish brown lean CLAY with few sand seams and cemented silt pockets
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate /A87
Plate
Made by:
Checked by:
200
180
160
140
120
100
80
60
40
20
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
53.6
1258
63
32
3.33
14.9
Soil Description:
0
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate /A88
Plate
Made by:
Checked by:
200
180
160
140
120
100
80
60
40
20
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
57.4
1601
114
57
0.70
15.0
Soil Description:
Stiff dark yellowish brown lean CLAY with few sand seams and cemented silt pockets
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A89
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
61.9
1686
270
135
2.06
13.5
Soil Description:
Very stiff dark greenish gray lean CLAY with few shell fragments and traces of silt pockets
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate /A90
Plate
Made by:
Checked by:
500
450
400
350
300
250
200
150
100
50
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
89.8
2216
386
193
0.77
15.0
Soil Description:
Very stiff greenish gray lean CLAY with sand with traces of silt pockets and shell fragments
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate/A91
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
93.6
2288
205
103
5.69
12.9
Soil Description:
Very stiff greenish gray lean CLAY with traces of shel fragments
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A92
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
93.6
2288
152
76
0.69
8.0
Soil Description:
0
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate/ A93
Made by:
Checked by:
400
360
320
280
240
200
160
120
80
40
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
97.6
2364
376
188
3.32
13.5
Soil Description:
Very stiff dark greenish gray lean CLAY with traces of silt and organic pockets and shell fragments
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate /A94
Plate
Made by:
Checked by:
400
360
320
280
240
200
160
120
80
40
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
97.6
2364
261
131
1.94
15.0
Soil Description:
0
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate/ A95
Plate
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
101.8
2444
295
148
3.81
14.9
Soil Description:
Very stiff dark greenish gray lean CLAY with traces of silt and organic pockets and shell fragments
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate/A96
Plate
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
101.8
2444
165
83
0.66
13.7
Soil Description:
0
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate/ A97
Made by:
Checked by:
400
360
320
280
240
200
160
120
80
40
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
105.8
2520
328
164
4.51
13.6
Soil Description:
Very stiff dark greenish gray lean CLAY with traces of silt and organic pockets and shell fragments
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate/A98
Plate
Made by:
Checked by:
400
360
320
280
240
200
160
120
80
40
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
105.8
2520
169
85
1.18
13.9
Soil Description:
0
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate /A99
Plate
Made by:
Checked by:
400
360
320
280
240
200
160
120
80
40
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
109.6
2592
369
185
3.59
14.9
Soil Description:
Very stiff dark greenish gray lean CLAY with few silt pockets and traces of shell fragments
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A100
Made by:
Checked by:
400
360
320
280
240
200
160
120
80
40
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
109.6
2592
240
120
0.60
11.4
Soil Description:
0
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate /A101
Plate
Made by:
Checked by:
500
450
400
350
300
250
200
150
100
50
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
113.4
2665
417
209
4.82
15.0
Soil Description:
Very stiff dark greenish gray lean CLAY with few silt pockets and traces of shell fragments
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A102
Made by:
Checked by:
500
450
400
350
300
250
200
150
100
50
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
113.4
2665
258
129
1.06
15.0
Soil Description:
0
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A103
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
136.7
3126
296
148
3.09
9.8
Soil Description:
Very stiff dark greenish gray sandy lean CLAY with little sand pockets, few shell fragments, and traces cemented sa
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : UNDISTURBED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate/A104
Plate
Made by:
Checked by:
300
270
240
210
180
150
120
90
60
30
10
12
14
16
18
20
STRAIN (%)
Cell Pressure
Maximum
Deviator Stress
Shear
Strength
50
Failure
Strain
(m)
(kPa)
(kPa)
(kPa)
(%)
(%)
136.7
3126
256
128
0.27
9.2
Soil Description:
0
Notes:
STRESS - STRAIN CURVE
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION TEST
TYPE OF TESTED SPECIMEN : REMOULDED
THIRD-PARTY SERVICES: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST ON COHESIVE SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-83
Rev.: 6
Effective: 21-02-2012
Plate
Plate /A105
Made By:
Checked By:
0.69
Void ratio, e .
0.63
Preconsolidation pressure
0.57
0.51
100
1000
10000
760
Void ratio, e .
0.65
Void ratio, e .
0.70
0.60
0.55
0.50
0.45
10
100
1000
10000
10
100
-4
Soil Description:
Hard brown lean CLAY with few silt pockets traces of shell fragments, organic and ferrous stains
Rev.: 6
Effective: 21-02-2012
Plate
A106
Plate 8/8
Made By:
Checked By:
0.73
Void ratio, e .
0.66
G
D
0.59
Preconsolidation pressure
0.52
100
1000
929
Void ratio, e .
0.75
Void ratio, e .
0.70
0.65
10000
0.60
0.55
0.50
0.45
10
100
1000
10000
10
100
-4
Soil Description:
Very stiff yellowish brown lean CLAY with sand with traces of shell fragments and silt pockets
Rev.: 6
Effective: 21-02-2012
Plate
A107
Plate 8/8
Tested By:
Checked By:
2500
2250
2000
1750
1500
1250
1000
750
500
250
Axial Strain, (%)
0
0
12
15
1500
1350
1200
1050
MOHR CIRCLES
900
750
600
450
300
150
Principal Stress, '(kPa)
0
0
' = 32
C' =
No
Stage
300
600
900
1200
1500
1800
2100
2400
2700
3000
575
400
6.61
443
175
618
II
850
400
3.23
1109
450
1559
III
1300
400
5.49
2124
900
3024
Soil Description:
Medium dense yellowish brown silty fine SAND with traces to few clay partings
CONSOLIDATED DRAINED TRIAXIAL COMPRESSION TEST
THIRD-PARTY SERVICE: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
BOREHOLE: SV-6X / SAMPLE P36C / SAMPLE DEPTH 49.7m
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-79
Rev.: 6
Effective: 21-02-2012
Plate
A108
Plate 3/3
Tested By:
Checked By:
3000
2700
2400
2100
1800
1500
1200
900
600
300
Axial Strain, (%)
0
0
10
12
14
2000
1800
1600
1400
MOHR CIRCLES
' =32O
1200
1000
800
600
400
200
Principal Stress, '(kPa)
0
0
400
800
1200
1600
2000
2400
2800
' = 32
C' = 10
No
Stage
3200
3600
4000
Cell
Back
Max. volume Max. deviator Effective ('3)Effective ('1)
pressure, kPa pressure, kPa change, cm3 stress, kPa
stress, kPa
stress, kPa
850
500
7.83
832
350
1182
II
1200
500
4.46
1716
700
2416
III
1500
500
4.30
2310
1000
3310
Soil Description:
Medium dense olive brown sandy SILT with traces of shell fragments and mica specks
CONSOLIDATED DRAINED TRIAXIAL COMPRESSION TEST
THIRD-PARTY SERVICE: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
BOREHOLE: SV-6X / SAMPLE P41B / SAMPLE DEPTH 69.4m
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-79
Rev.: 6
Effective: 21-02-2012
Plate 3/3
Plate
A109
Tested By:
Checked By:
5000
4500
4000
3500
3000
2500
2000
1500
1000
500
Axial Strain, (%)
0
0
10
12
14
2500
2250
2000
1750
MOHR CIRCLES
' =35O
1500
1250
1000
750
500
250
Principal Stress, '(kPa)
0
0
' = 35
C' =
No
Stage
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
965
400
1.31
1592
565
2157
II
1530
400
1.48
3133
1130
4263
III
2095
400
2.30
4594
1695
6289
Soil Description:
Medium dense dark gray poorly graded fine SAND with traces of shell fragments
CONSOLIDATED DRAINED TRIAXIAL COMPRESSION TEST
THIRD-PARTY SERVICE: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
BOREHOLE: SV-6X / SAMPLE P54B / SAMPLE DEPTH 121.4m
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-79
Rev.: 6
Effective: 21-02-2012
Plate 3/3
Plate
A110
Made By:
100
100
75
75
50
50
25
25
Checked By:
0
0
10
25
HORIZONTAL DISPLACEMENT L, mm
Normal Stress,
kPa
Shear Stress,
kPa
1 = 22
= 25
2 = 46
39
3 = 95
64
50
75
100
C'
kPa
'
deg.
13
28.0
Remarks
Borehole : SV-6X
Sample No:
P1B
Initial Water Content (%): 34.2
Soil Description:
Calcareous medium dense dark greenish gray silty fine SAND with few to some shell fragments
Notes:
SATURATED DRAINED RAPID DIRECT SHEAR TEST
STRESS-DISPLACEMENT CURVES & PLOT OF SHEAR STRESS
TYPE OF TESTED SPECIMEN :
UNDISTURBED
THIRD -PARTY SERVICE: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST FOR COHESIONLESS SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-82
Rev.: 6
Effective: 21-02-2012
Plate ./A111
Plate
Made By:
100
100
75
75
50
50
25
25
Checked By:
0
0
10
25
HORIZONTAL DISPLACEMENT L, mm
Normal Stress,
kPa
Shear Stress,
kPa
1 = 25
= 24
2 = 50
41
3 = 98
67
50
75
100
C'
kPa
'
deg.
10
29.0
Remarks
Borehole : SV-6X
Sample No:
P2A
Initial Water Content (%): 27.4
Soil Description:
Calcareous medium dense dark greenish gray silty fine SAND with few to some shell fragments
Notes:
SATURATED DRAINED RAPID DIRECT SHEAR TEST
STRESS-DISPLACEMENT CURVES & PLOT OF SHEAR STRESS
TYPE OF TESTED SPECIMEN :
UNDISTURBED
THIRD -PARTY SERVICE: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST FOR COHESIONLESS SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-82
Rev.: 6
Effective: 21-02-2012
Plate
Plate./A112
Made By:
100
100
75
75
50
50
25
25
Checked By:
0
0
10
25
HORIZONTAL DISPLACEMENT L, mm
Normal Stress,
kPa
Shear Stress,
kPa
1 = 22
= 27
2 = 46
44
3 = 95
67
50
75
100
C'
kPa
'
deg.
16
28.0
Remarks
Borehole : SV-6X
Sample No:
P3C
Initial Water Content (%): 22.7
Soil Description:
Medium dense reddish brown silty fine SAND with few clay pockets
Notes:
SATURATED DRAINED RAPID DIRECT SHEAR TEST
STRESS-DISPLACEMENT CURVES & PLOT OF SHEAR STRESS
TYPE OF TESTED SPECIMEN :
UNDISTURBED
THIRD -PARTY SERVICE: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST FOR COHESIONLESS SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-82
Rev.: 6
Effective: 21-02-2012
Plate
Plate./A113
Made By:
100
100
75
75
50
50
25
25
Checked By:
0
0
10
25
HORIZONTAL DISPLACEMENT L, mm
Normal Stress,
kPa
Shear Stress,
kPa
1 = 22
= 25
2 = 46
38
3 = 95
63
50
75
100
C'
kPa
'
deg.
14
27.5
Remarks
Borehole : SV-6X
Sample No:
P5B
Initial Water Content (%): 17.9
Soil Description:
Medium dense dark yellowish brown silty fine SAND
Notes:
SATURATED DRAINED RAPID DIRECT SHEAR TEST
STRESS-DISPLACEMENT CURVES & PLOT OF SHEAR STRESS
TYPE OF TESTED SPECIMEN :
RECONSTITUTED
THIRD -PARTY SERVICE: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST FOR COHESIONLESS SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-82
Rev.: 6
Effective: 21-02-2012
Plate ./A114
Plate
Made By:
200
200
150
150
100
100
50
50
Checked By:
0
0
10
50
HORIZONTAL DISPLACEMENT L, mm
Normal Stress,
kPa
Shear Stress,
kPa
1 = 39
= 40
2 = 81
70
3 = 161
108
100
150
200
C'
kPa
'
deg.
20
28.5
Remarks
Borehole : SV-6X
Sample No:
P9C
Initial Water Content (%): 25.6
Soil Description:
Medium dense yellowish brown none plasticity sandy SILT with traces cemented sand, clay and organic pockets
Notes:
SATURATED DRAINED RAPID DIRECT SHEAR TEST
STRESS-DISPLACEMENT CURVES & PLOT OF SHEAR STRESS
TYPE OF TESTED SPECIMEN :
UNDISTURBED
THIRD -PARTY SERVICE: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST FOR COHESIONLESS SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-82
Rev.: 6
Effective: 21-02-2012
Plate ./A115
Plate
Made By:
200
200
150
150
100
100
50
50
Checked By:
0
0
10
50
HORIZONTAL DISPLACEMENT L, mm
Normal Stress,
kPa
Shear Stress,
kPa
1 = 43
= 42
2 = 88
70
3 = 175
115
100
150
200
C'
kPa
'
deg.
20
28.0
Remarks
Borehole : SV-6X
Sample No:
P10B
Initial Water Content (%): 25.0
Soil Description:
Medium dense yellowish brown none plasticity SILT with sand with traces cemented sand, clay and organic pockets
Notes:
SATURATED DRAINED RAPID DIRECT SHEAR TEST
STRESS-DISPLACEMENT CURVES & PLOT OF SHEAR STRESS
TYPE OF TESTED SPECIMEN :
UNDISTURBED
THIRD -PARTY SERVICE: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST FOR COHESIONLESS SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-82
Rev.: 6
Effective: 21-02-2012
Plate ./A116
Plate
Made By:
200
200
150
150
100
100
50
50
Checked By:
0
0
10
50
HORIZONTAL DISPLACEMENT L, mm
Normal Stress,
kPa
Shear Stress,
kPa
1 = 46
= 45
2 = 98
67
3 = 196
122
100
150
200
C'
kPa
'
deg.
22
26.0
Remarks
Borehole : SV-6X
Sample No:
P11B
Initial Water Content (%): 25.5
Soil Description:
Medium dense yellowish brown none plasticity SILT with sand with traces cemented sand, clay and organic pockets
Notes:
SATURATED DRAINED RAPID DIRECT SHEAR TEST
STRESS-DISPLACEMENT CURVES & PLOT OF SHEAR STRESS
TYPE OF TESTED SPECIMEN :
UNDISTURBED
THIRD -PARTY SERVICE: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST FOR COHESIONLESS SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-82
Rev.: 6
Effective: 21-02-2012
Plate ./A117
Plate
Made By:
1000
1000
800
800
600
600
400
400
200
200
Checked By:
0
0
10
200
HORIZONTAL DISPLACEMENT L, mm
Normal Stress,
kPa
Shear Stress,
kPa
1 = 265
= 159
2 = 459
266
3 = 917
558
400
600
800
1000
C'
kPa
'
deg.
10
29.5
Remarks
Borehole : SV-6X
Sample No:
P35A
Initial Water Content (%): 23.6
Soil Description:
Medium dense yellowish brown sandy SILT with few cemented silt and traces of shell fragments pockets
Notes:
SATURATED DRAINED RAPID DIRECT SHEAR TEST
STRESS-DISPLACEMENT CURVES & PLOT OF SHEAR STRESS
TYPE OF TESTED SPECIMEN :
UNDISTURBED
THIRD -PARTY SERVICE: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST FOR COHESIONLESS SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-82
Rev.: 6
Effective: 21-02-2012
Plate ./A118
Plate
Made By:
1200
1200
900
900
600
600
300
300
Checked By:
0
0
10
300
HORIZONTAL DISPLACEMENT L, mm
Normal Stress,
kPa
Shear Stress,
kPa
1 = 393
= 273
2 = 789
477
3 = 1198
753
600
900
1200
C'
kPa
'
deg.
20
31.0
Remarks
Borehole : SV-6X
Sample No:
P43B
Initial Water Content (%): 23.0
Soil Description:
Dense olive brown none plasticity sandy SILT with traces of cemented sand pockets
Notes:
SATURATED DRAINED RAPID DIRECT SHEAR TEST
STRESS-DISPLACEMENT CURVES & PLOT OF SHEAR STRESS
TYPE OF TESTED SPECIMEN :
UNDISTURBED
THIRD -PARTY SERVICE: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST FOR COHESIONLESS SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-82
Rev.: 6
Effective: 21-02-2012
Plate./A119
Plate
Made By:
1200
1200
900
900
600
600
300
300
Checked By:
0
0
10
300
HORIZONTAL DISPLACEMENT L, mm
Normal Stress,
kPa
Shear Stress,
kPa
1 = 400
= 288
2 = 799
508
3 = 1198
780
600
900
1200
C'
kPa
'
deg.
15
32.5
Remarks
Borehole : SV-6X
Sample No:
P44A
Initial Water Content (%): 34.5
Soil Description:
Medium dense dark greenish gray silty fine SAND with few shell fragments and traces of clay pockets
Notes:
SATURATED DRAINED RAPID DIRECT SHEAR TEST
STRESS-DISPLACEMENT CURVES & PLOT OF SHEAR STRESS
TYPE OF TESTED SPECIMEN :
UNDISTURBED
THIRD -PARTY SERVICE: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST FOR COHESIONLESS SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-82
Rev.: 6
Effective: 21-02-2012
Plate
Plate ./A120
Made By:
1200
1200
900
900
600
600
300
300
Checked By:
0
0
10
300
HORIZONTAL DISPLACEMENT L, mm
Normal Stress,
kPa
Shear Stress,
kPa
1 = 400
= 300
2 = 799
561
3 = 1198
792
600
900
1200
C'
kPa
'
deg.
17
33.0
Remarks
Borehole : SV-6X
Sample No:
P45B
Initial Water Content (%): 25.5
Soil Description:
Medium dense dark greenish gray silty fine SAND with few shell fragments and traces of clay pockets
Notes:
SATURATED DRAINED RAPID DIRECT SHEAR TEST
STRESS-DISPLACEMENT CURVES & PLOT OF SHEAR STRESS
TYPE OF TESTED SPECIMEN :
UNDISTURBED
THIRD -PARTY SERVICE: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST FOR COHESIONLESS SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-82
Rev.: 6
Effective: 21-02-2012
Plate ./A121
Plate
Made By:
1600
1600
1200
1200
800
800
400
400
Checked By:
0
0
10
400
HORIZONTAL DISPLACEMENT L, mm
Normal Stress,
kPa
Shear Stress,
kPa
1 = 500
= 344
2 = 999
559
3 = 1500
852
800
1200
1600
C'
kPa
'
deg.
18
30.0
Remarks
Borehole : SV-6X
Sample No:
P53B
Initial Water Content (%): 22.8
Soil Description:
Medium dense dark gray silty fine SAND with few cemented sand and traces of clay pockets
Notes:
SATURATED DRAINED RAPID DIRECT SHEAR TEST
STRESS-DISPLACEMENT CURVES & PLOT OF SHEAR STRESS
TYPE OF TESTED SPECIMEN :
UNDISTURBED
THIRD -PARTY SERVICE: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST FOR COHESIONLESS SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-82
Rev.: 6
Effective: 21-02-2012
Plate ./A122
Plate
Made By:
1600
1600
1200
1200
800
800
400
400
Checked By:
0
0
10
400
HORIZONTAL DISPLACEMENT L, mm
Normal Stress,
kPa
Shear Stress,
kPa
1 = 401
= 286
2 = 801
501
3 = 1200
794
800
1200
1600
C'
kPa
'
deg.
10
33.0
Remarks
Borehole : SV-6X
Sample No:
P55B
Initial Water Content (%): 25.8
Soil Description:
Medium dense dark gray silty fine SAND with some shell fragments
Notes:
SATURATED DRAINED RAPID DIRECT SHEAR TEST
STRESS-DISPLACEMENT CURVES & PLOT OF SHEAR STRESS
TYPE OF TESTED SPECIMEN :
UNDISTURBED
THIRD -PARTY SERVICE: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST FOR COHESIONLESS SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-82
Rev.: 6
Effective: 21-02-2012
Plate./A123
Plate
Made By:
1600
1600
1200
1200
800
800
400
400
Checked By:
0
0
10
400
HORIZONTAL DISPLACEMENT L, mm
Normal Stress,
kPa
Shear Stress,
kPa
1 = 500
= 356
2 = 999
617
3 = 1500
1002
800
1200
1600
C'
kPa
'
deg.
15
33.0
Remarks
Borehole : SV-6X
Sample No:
P56C
Initial Water Content (%): 19.3
Soil Description:
Medium dense dark gray silty fine SAND with some shell fragments with traces of clay pockets
Notes:
SATURATED DRAINED RAPID DIRECT SHEAR TEST
STRESS-DISPLACEMENT CURVES & PLOT OF SHEAR STRESS
TYPE OF TESTED SPECIMEN :
UNDISTURBED
THIRD -PARTY SERVICE: SOIL LABORATORY ANALYSIS FOR CUU LONG JOC
SHEAR STRENGTH TEST FOR COHESIONLESS SOIL
VIETSOVPETRO GEOTECH-LAB. INDEX: LAS-XD901
F-C-82
Rev.: 6
Effective: 21-02-2012
Plate ./A124
Plate
ANALYSIS REPORT
BLOCK 15-1:
Sample:
Requirement:
Date sample received:
Date tested:
Analytical method:
BH SV-6X
Soils
Determination of Carbonate Content
06 May. 2013
06 - 10 May. 2013
Rapid Titration Method in Accordance with 6.3
of BS-1377: Part 3 : 1990
Analysis results:
No
Sample
Depth(m)
%Carbonate(as CO2)
%Carbonate( as CaCO3)
P2A
1.2
5.25
11.93
P5C
4.6
0.03
0.07
P36C
49.7
1.18
2.69
P54B
121.4
2.50
5.67
Analysts:
Checked
Plate A125
Date performed:
BH SV-6X
BLOCK 15-01
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
PGS/SI/2013/CLJOC/06/DR
20/06/2013
Made by
SP
Checked by
CHG
Plate A126
Date performed:
BH SV-6X
BLOCK 15-01
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
PGS/SI/2013/CLJOC/06/DR
20/06/2013
Made by
SP
Checked by
CHG
Plate A127
Date performed:
BH SV-6X
BLOCK 15-01
OFFSHORE VIETNAM
CUU LONG JOINT OPERATING COMPANY (CLJOC)
PGS/SI/2013/CLJOC/06/DR
20/06/2013
Made by
SP
Checked by
CHG
Plate A128
APPENDIX B
Soil Colour
The soil colours were measured by comparison with a Munsell soil colour chart. (Reference:
Munsell Soil Color Charts, 1975 Edition). Accurate comparison was obtained by holding the soil
sample directly behind apertures separating the closest matching colour chips. The soil colours
were described by colour names and the Munsell notation of color.
In the Munsell system, the colours were systematically arranged in accordance with the three
variables that combined to describe all colours.
Chroma. The Hue notation of a colour indicated its relation to Red, Yellow, Green, Blue and
Purple.
The Value notation indicated its strength (or departure from a neutral of the same
lightness).
Atterberg Limits
The tests to determine the Atterberg Limits were conducted on soil samples of cohesive material.
The specimen was sieved through a sieve 425 m. The soil passing the 425 m sieve was
thoroughly mixed with distilled water. The liquid and plastic limits of the soil were then determined
in accordance with ASTM D 0423 & D 0424.
The sample was mixed with water and stirred for about 15 minutes.
dispersing agent was added to prevent flocculation of the soil particles. After mixing, the density
of the water-soil slurry was measured at fixed time intervals with a hydrometer. The particle size
distribution of the sedimented particles was determined. For particle size coarser than 0.06 mm,
the samples were dried and sieved through a set of standard sieves for the gradings.
DESCRIPTION OF LABORATORY
TESTING PROCEDURES
PGS/SI/2013/CLJOC/06/SV-6X/FR
Plate B1
Moisture Content
The wet sample was dried for 24 hours at a temperature of 105C. The weight of the moisture
of the soil was taken from the loss in weight of the sample due to drying and was presented as
percentage of the dry weight of the soil. This test was performed in accordance with ASTM D
2216.
Unit Weights
The unit weights were computed from the wet and dry weights of a standard volume of soil (33.3
cm3). The dry weight was obtained after the wet standard volume of soil was dried for 24 hours
at a temperature of 105C.
Specific Gravity
The unit weight of the solid particles of the soil was determined by means of stoppered bottles
having a volume of 50 ml. The bottle was filled with distilled water and weighed to determine
the unit weight of the water. The bottle was partly filled with distilled water in which 10g of dry
crumbled soil was added, entrapped air was removed by subjecting the contents of the bottle to
a vacuum. The bottle was then completely filled up with distilled water and weighted. The unit
weight of the particles of the soil was computed with these data. The weights of bottle and
contents were determined at a temperature of the bottle and contents of 20C. The tests were
performed in accordance with ASTM D 0854.
DESCRIPTION OF LABORATORY
TESTING PROCEDURES
PGS/SI/2013/CLJOC/06/SV-6X/FR
Plate B2
Lab Vane
A calibrated 4-blade vane fastened to the bottom of a vertical rod was pushed into the soil at the
bottom of the sample tube with the blade fully embedded. A torque (machine controlled) was
applied to turn the vane via a calibrated spring. The undrained shear strength was derived from
a calibration charts with vane/spring curves as torque versus undrained shear strength.
Torvane
A flat surface was prepared on the cohesive sample. The metal disk with thin radial vanes of
the torvane was pressed carefully against the soil surface with the vanes fully embedded. The
knob attached to one end of the calibrated torsional spring was turned slowly at a constant rate
with finger pressure. The soil enclosed within the vanes were sheared from the sample at a
certain torsional moment. The indicator moved along the scale and stayed automatically at the
position corresponding to the maximum torsion of the spring which was calibrated to indicate
directly shear strength of the soil (maximum capacity 20, 100 or 250 kN/m2, depending on the
adopter used Soil Test CL 602, CL 600 or CL 604 respectively).
Pocket Penetrometer
The stylus was pushed with a steady pressure into the soil until a penetration of about one
stylus diameter was reached and the indicator ring along the scale moved and hold
automatically at the position corresponding to the maximum compression of the spring. The
undrained shear strength of the soil was taken as one-half the unconfined compressive strength
(maximum capacity of the penetrometer 250 kN/m2).
DESCRIPTION OF LABORATORY
TESTING PROCEDURES
PGS/SI/2013/CLJOC/06/SV-6X/FR
Plate B3
The specimen of disturbed soil was prepared on the base of the shear box apparatus. Soil particles
larger than 20% of thickness of the specimen to be tested were removed. The sample was
compacted to a density as close as possible to the undisturbed density. On completion of the setup,
the specimen was saturated. Then, apply the desired normal load for consolidation. After primary
consolidation is completed, the sample was subjected to vertical loading, i.e. the normal stress
applied on the sample and the sample was sheared along the predetermined failure plane at a
sufficiently speed shearing reference to the consolidation graft to permit drainage.
For second and third specimen, the process repeated but the normal stress was increased. The
normal stress was kept constant during each shearing stage. A total of three loading stages for
increasing pressure were conducted. The results of the test were presented as Mohr criterion of
shearing failure, defined as the angle of internal friction,, and the cohesion intercept, c.
The consolidation compressibility characteristics of the soil were determined by performing the
oedometer tests. The test was conducted in accordance with specifications given by T.W.
Lambe in Soil Testing for Engineers (John Wiley and Sons, New York, Sixth Printing; 1960).
The samples were prevented from swelling before the first load was applied on the samples and
the results of the tests were presented as void ratio v/s pressure (e-log p curves).
DESCRIPTION OF LABORATORY
TESTING PROCEDURES
PGS/SI/2013/CLJOC/06/SV-6X/FR
Plate B4
SOIL TYPES
Clay
Sand
Silt
Gravel
Rock
Organic matter
COHESIONLESS SOILS
CONSISTENCY
ESTIMATED RELATIVE
DESCRIPTIVE TERM
STRENGTH (kN/m)
DENSITY
Very Soft
0 12
Very Loose
0 0.15
Soft
12 25
Loose
0.15 0.35
Firm
25 50
Medium Dense
0.35 0.65
Stiff
50 100
Dense
0.65 0.85
Very Stiff
100 200
Very Dense
0.85 1.00
Hard
200 400
Very Hard
> 400
US STANDARD SIEVE
10
4
40
GRAVEL
SAND
CLAY OR SILT
FINE
0.075
MEDIUM
0.425
COARSE
FINE
2.00
4.75
SOIL GRAIN SIZE IN MILIMETERS
3
COBBLES
COARSE
19
75
SOIL COLOUR
SOIL STRUCTURE
Traces
Few
Little
Some
Slickensided
Fissured
Containing shrinkage or relief crack, often filled with fine sand or silt; usually more or less vertical.
Inclusion of material of different texture that is smaller than the diameter of the sample.
Parting
Seam
Layer
Laminated
Interlayed
Intermixed
Soil sample composed of pockets of different soil type and layered or laminated structure is not evident.
Calcareous
Plate B5
100
10
0.1
0
0.2
0.4
0.6
0.8
1.2
1.4
100
10
0.1
-0.2
5.
6.
7.
8.
9. Sand
10. Gravelly sand to sand
11. Very stiff fine grained *
12. Sand to clayey sand *
* Overconsolidated or cemented
Plate B6
APPENDIX C
MV PTSC SURVEYOR
PGS/SI/2013/CLJOC/06/SV-6X/FR
Plate C1
PGS/SI/2013/CLJOC/06/SV-6X/FR
Plate C2
DATE
TIME
FROM
TO
ACTIVITIES
16-04-13
2300
2400
17/04/13
0000
1315
1315
1700
1700
1915
18-04-13
0000
1110
1430
1110
1430
2400
19-04-13
0000
0855
1105
0855
1105
1250
Date Performed :
19/06/2013
Made by
SP
Checked by
CHG
Plate C3