0 Bewertungen0% fanden dieses Dokument nützlich (0 Abstimmungen)
168 Ansichten2 Seiten
The communication subrack 560CSR01 is designed to house the communication modules of an RTU560 remote terminal unit. It has 11 slots for modules including 2 slots for redundant power modules, 8 slots for communication modules, and 1 slot for a real time clock or bus module. All module connections are made via a backplane and the subrack connects to the outside world through front panel connectors. It has dimensions of 133 x 483 x 200 mm and supports DIN standard modules in a 19" rack form factor.
The communication subrack 560CSR01 is designed to house the communication modules of an RTU560 remote terminal unit. It has 11 slots for modules including 2 slots for redundant power modules, 8 slots for communication modules, and 1 slot for a real time clock or bus module. All module connections are made via a backplane and the subrack connects to the outside world through front panel connectors. It has dimensions of 133 x 483 x 200 mm and supports DIN standard modules in a 19" rack form factor.
The communication subrack 560CSR01 is designed to house the communication modules of an RTU560 remote terminal unit. It has 11 slots for modules including 2 slots for redundant power modules, 8 slots for communication modules, and 1 slot for a real time clock or bus module. All module connections are made via a backplane and the subrack connects to the outside world through front panel connectors. It has dimensions of 133 x 483 x 200 mm and supports DIN standard modules in a 19" rack form factor.
ABB Utilities GmbH 31 Doc.- -No.: 1KGT 150 411 V000 1 Data Sheet Communication Subrack 560CSR01 Application The communication sub rack 560CSR01 is designed to accept the CMUs (CMU = communication unit) of a RTU560 remote terminal unit. The 560CSR01 is installed in a swing frame cabinet or in a frame. The communication sub rack is prepared to take the power modules, communication modules, real time module and a bus communication module. All necessary connections between the modules are done via the backplane. All connections to the outside are done via their connectors on the front panel. The communication sub rack itself has no connections to the outside. Characteristics The 19 board rack has a height of 3 HE for single eurocard format boards (DIN 41494). There are 11 slots available for the installation of the boards. Allocation of the Slots: h 2 slots for redundant power modules. Each module 2 units width. h 8 slots for communication modules. Each module 2 units width. h 1 slot for real time clock module or a bus connection unit. 1 unit width. For the physical interfacing of boards edge connectors of type F (DIN 41612) are used, which are directly soldered to the printed circuit board. All signals of the RTU560 system bus are connected with this connectors. The communication sub rack itself has no other connections. Mounted to the communication sub rack 560CSR01 the 4 pole DIL switch S1 is to configure the internal RTU560 system bus and the address switching for the communication subrack. ABB Utilities GmbH RTU560 Data Sheet Communication Subrack 560CSR01 32 Doc.- -No.: 1KGT 150 411 V000 1 Front view 1 3 3 m m 483 mm 560PSU01 5 V 24 V ON 0FF UE + UE -- PE 560BCU01 ALR WRN TSI TSO SEB 560PSU01 5 V 24 V UE + UE -- PE ON 0FF 560ETH01 A A MMI E C E ERR Tx Rx CE A B 560SLI01 A B 1 2 A B 1 2 Tx Rx ERR MMI CE 1 2 3 4 O F F 560ETH01 A B A MMI E C E ERR Tx Rx CE A B B 560SLI01 A B 1 2 A B 1 2 Tx Rx ERR MMI CE S1 Technical Data In addition to the general technical data of the RTU560, the following applies: Subrack 19, 3 HE, 21 slot following DIN 41494 1 slot = 4 units = 20.32 mm Dimensions: 133 x 483 x 200 mm (H x W x D) Types of Connection Peripheral boards: 11 connectors female, 48 pole Type F DIN 41612 Slot Configuration h Slot address 1 board address P1 and slot address 9 board address P2 for 2 redundant power modules. Each 2 slots in width. h Slot addresses/board addresses 17/8, 25/7, 33/6, 41/5, 49/4, 57/3, 65/2 and 73/1 for communication modules. Each 2 slots in width. h Slot address 81 board address 0 for real time clock module or a bus communication module. 1 slot in width. Protection Earth- / Shield terminal Must be caused by electric conductive screwing to the frame or a cable plug screwed to the rack. Environmental Conditions Temperature 0 ... 70 _C Rel. humidity: 5 ... 95% (non condensing) Ordering Information For swing frame mounting 560CSR01R011 1KGT 006 300 R0011 For frame mounting 560CSR01R0012 1KGT 006 300 R0012 ABB Utilities GmbH Kallstadter Strae 1 68309 Mannheim (Germany) Telephone +49 (0) 621 381-7592 Telefax +49 (0) 621 381-7622 03/2001 Subject to alteration