1. Channel Planning Configured items Number of Chs supported by Huawei NCP 1 CCP 1 to 12 EF AF41 AF21 AF11 OAM OM channel 1 Note 1: Number of CCPs Note 2PATH Type From RAN 11, the PATH Type is used to distinguish PHB but not traffic(i.e.R99 or H, RT or NRT in RAN10). 2. Bandwidth Planning Tx(kbps) NCP CCP EF Physical Link BW AF41 Physical Link BW AF21 Physical Link BW AF11 Physical Link BW Note 3: Bandwidth of NCP&CCP Note 4: DSCP value of SIG General Rules of Iub Tx Configuration (1) The default DSCP value of Signal Plane is 48, which can be changed by ADD SCTPLNK or MOD SCTPLNK command in RNC side, 48 is the recommended value. In NodeB side, SIG DSCP is set to 48 using command( SET DIFPRI(SIG) ) (2) The DSCP value of user palne is configurated by SET PHBMAP command in RNC side. Signal Plane When Huawei RNC and Huawei NodeB connected, one CCP link is enough. To be consistent with the 3GPP protocol, Huawei RNC&NodeB also support multiple CCPs, but it is not recommended by Huawei. User Plane The bandwidth of NCP&CCP is no need to be configured, the DSCP priority guarantees the signaling transmission. 1 to 16 Signal Plane User Plane OAM OMIP 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 1 of 80 235388102.xlsx.ms_office SecurityFor Internal Note 5: Bandwidth of IPPATH Note 6: Bandwidth of OAM Channel Note 7: CIR&CBS&EBS 2. Tx related Algorithm Value enable enable enable enable enable 80% 70% 40% Note 8: Congestion Control Threshold 3. PHB Priority AF1i AF2i AF11 AF12 AF13 AF21 AF22 AF23 DSCP(default) 10 12 14 18 20 22 Note 9: Use SET PHBMAP command to modify the mapping between PHB and DSCP. 4. VLAN Configuration Rules Note 10: In RNC sidet here are two typical scenarios to access RNC which show as follows: scenario 1: access RNC via router(s) The user data bandwidth configured is equal to physical link bandwidth or maximum requirement bandwidth according to actual traffic. The Physical Link BW is the minimum bandwidth of physical link connection between RNC and NodeB. Common Channel factor Interactive and background service factor Switches CIR:Committed Information Rate(bit/s) CBS:Committed Burst Size(bit) EBS:Excess Burst Size (bit) The CIR means the bandwidth of guarantee rate of the physical link. The CBS configuration is recommended to one and a half of the CIR, and the EBS configuration is recommended to "0". The total bandwidth of the CBS and the EBS should be no less than the CIR/1000(bit). NodeB MMLCommand: SET LR Configuration Item The bandwidth of OM channel is no need to be configured, the RR scheduling method and the DSCP priority guarantee the daily O&M traffic. The bandwidth for initial BE traffic and PS handover should be taken into account. DCCC Iub bandwidth CAC Iub congestion control Congestion Control Threshold Active factor Iub overbooking HSDPA Flow Control PHB 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 2 of 80 235388102.xlsx.ms_office SecurityFor Internal For this scenario, the recommended mode is not to set VLAN in RNC side. scenario 2: access RNC via MSTP or other L2 network device. For this scenario it is better to just add one VLAN for each IP address by ADD VLANID command. Multiple VLAN need more IP addresses. Note 11: In NodeB side, you can set single VLAN for a nexthop IP address that all data passing through this nexthop IP address have the same VLAN ID and VLAN priority. The recommended mode is SINGLEVLAN after RAN13 version. Related MML command: ADD VLANMAP 5. Other Configuration Rules Note 12: Note 13: In NodeB side, data of user voice and PS domain servicesdownloaded data by the user using HSDPA and uploaded data by the user using HSUPAThe DSCPs priority of these NodeB Tx UDP packets are addressed by the RNC to the NodeB when the connection is set up. The DSCP settings are decided by the configuration of the RNC. Note 14: In NodeB side, common signaling messages are carried on the cell common channel and uplink flow control frames of HSDPA are sent from NodeB to RNC. These two types of data are transmitted by UDP packets. The DSCP value of these Tx UDP packets is the same as the value of the Signal Priority parameter of the SET DIFPRI command. If we select the "VLANGROUP" mode in command "ADD VLANMAP" when configuring VLAN in NodeB side, make sure to configure the VLAN ID of USERDATA with this DSCP value in command "ADD VLANCLASS". 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 3 of 80 235388102.xlsx.ms_office SecurityFor Internal Note 15: In both RNC and Node sides, VLAN support means labeling the Tx data but not the Rx data,NodeB can receive all types of packets,regardless of VLAN or unVLAN. Note 16: The destination IP address is not recommended to be set to 0.0.0.0 in NodeB in IP transmission. If the bear type of a remote maintenance channel is set to ATM, do not set the destination IP address to 0.0.0.0 for a IP route. In NodeB side, the DSCPs of DHCP is 0. But about ICMP packets, there is difference between sending and responding, when sending independent, the DSCP of ICMP can be configured; nevertheless, when responding, the DSCP of ICMP is refilled according to the corresponding ICMP packets received. 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 4 of 80 235388102.xlsx.ms_office SecurityFor Internal Number of Chs recommended by Huawei 1 1 1 1 1 1 1 From RAN 11, the PATH Type is used to distinguish PHB but not traffic(i.e.R99 or H, RT or NRT in RAN10). Rx(kbps) DSCP Value 48 48 Physical Link BW 46 Physical Link BW 34 Physical Link BW 18 Physical Link BW 10 46 18 General Rules of Iub Tx Configuration (1) The default DSCP value of Signal Plane is 48, which can be changed by ADD SCTPLNK or MOD SCTPLNK command in RNC side, 48 is the recommended value. In NodeB side, SIG DSCP is set to 48 using command( SET DIFPRI(SIG) ) (2) The DSCP value of user palne is configurated by SET PHBMAP command in RNC side. When Huawei RNC and Huawei NodeB connected, one CCP link is enough. To be consistent with the 3GPP protocol, Huawei RNC&NodeB also support multiple CCPs, but it is not recommended by Huawei. The bandwidth of NCP&CCP is no need to be configured, the DSCP priority guarantees the signaling transmission. 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 5 of 80 235388102.xlsx.ms_office SecurityFor Internal AF3i AF4i EF BE AF31 AF32 AF33 AF41 AF42 AF43 26 28 30 34 36 38 46 0 The user data bandwidth configured is equal to physical link bandwidth or maximum requirement bandwidth according to actual traffic. The Physical Link BW is the minimum bandwidth of physical link connection between RNC and NodeB. CIR:Committed Information Rate(bit/s) CBS:Committed Burst Size(bit) EBS:Excess Burst Size (bit) The CIR means the bandwidth of guarantee rate of the physical link. The CBS configuration is recommended to one and a half of the CIR, and the EBS configuration is recommended to "0". The total bandwidth of the CBS and the EBS should be no less than the CIR/1000(bit). NodeB MMLCommand: SET LR The bandwidth of OM channel is no need to be configured, the RR scheduling method and the DSCP priority guarantee the daily O&M traffic. The bandwidth for initial BE traffic and PS handover should be taken into account. 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 6 of 80 235388102.xlsx.ms_office SecurityFor Internal In NodeB side, you can set single VLAN for a nexthop IP address that all data passing through this nexthop IP address have the same VLAN ID and VLAN priority. In NodeB side, data of user voice and PS domain servicesdownloaded data by the user using HSDPA and uploaded data by the user using HSUPAThe DSCPs priority of these NodeB Tx UDP packets are addressed by the RNC to the NodeB when the connection is set up. The DSCP settings are decided by In NodeB side, common signaling messages are carried on the cell common channel and uplink flow control frames of HSDPA are sent from NodeB to RNC. These two types of data are transmitted by UDP packets. The DSCP value of these Tx UDP packets is the same as the value of the Signal Priority parameter of the SET DIFPRI command. If we select the "VLANGROUP" mode in command "ADD VLANMAP" when configuring VLAN in NodeB side, make sure to configure the VLAN ID of USERDATA with this DSCP value in command "ADD VLANCLASS". 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 7 of 80 235388102.xlsx.ms_office SecurityFor Internal In both RNC and Node sides, VLAN support means labeling the Tx data but not the Rx data,NodeB can receive all types of packets,regardless of VLAN or unVLAN. The destination IP address is not recommended to be set to 0.0.0.0 in NodeB in IP transmission. If the bear type of a remote maintenance channel is set to ATM, do not set the destination IP address to 0.0.0.0 for a IP route. In NodeB side, the DSCPs of DHCP is 0. But about ICMP packets, there is difference between sending and responding, when sending independent, the DSCP of ICMP can be configured; nevertheless, when responding, the DSCP of ICMP is refilled according to the corresponding ICMP packets received. 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 8 of 80 235388102.xlsx.ms_office SecurityFor Internal General Rules of Iub Tx Configuration 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 9 of 80 235388102.xlsx.ms_office SecurityFor Internal Table 1 Tx(kbps) NCP CCP EF Physical Link BW AF41 Physical Link BW AF21 Physical Link BW AF11 Physical Link BW Note 2: Note 3: Note 4: Table2 TRMMAP Configuration Rules The TRMMAP configuration can be added or modified by the command "ADD/MOD TRMMAP", unless the TRMMAP ID is from 0-13; If there is 2 to 6 queues in transmission, please refer to table 2 in sheet "IUB IP QoS". Table 3 Traffic type VLAN ID Command Sig ADD VLANID EF AF41 AF21 AF11 ARP ICMP(manual) DHCP Tracert BFD PING MAC ADD CFMMA OAM OMIP Huawei RNC Configuration ADD VLANID OM ADD VLANID Scenario 1: FE Signal Plane User Plane Note 1: The FE/GE port work mode should be consulted with the peer device. Local Peer 1)100M/FULL 100M/FULL 2)1000M/FULL 1000M/FULL 3) AUTO AUTO The Physical Link BW is the minimum bandwidth of physical link connection between RNC and NodeB. It is recommended to set the value of parameter "IPPATH Ping Check Type" to "UDP". The recommended TRMMAP is not the default TRMMAP,please use the recommended TRMMAP. Refer to table 2 as following. Keeping the TRMMAP mapping relationship is preferred if the RNC is updated from old version. VLAN configuration User Data Other ADD VLANID 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 10 of 80 235388102.xlsx.ms_office SecurityFor Internal IPPM same as corresponding IPPATH Note1 Note2 Note3 Note4 Note5: The DSCP Value or VLAN priority used in RAN should be planned in Transmission Device, and make sure the Transmission Device will not change the Values Table 4 DSCP NCP 48 CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46High 18Low Note 1: Note 2: Scenario 1: FE CIR:Committed Information Rate(bit/s); CBS:Committed Burst Size(bit); EBS:Excess Burst Size (bit); The CIR means the bandwidth of guarantee rate of the physical link. The CBS configuration is recommended to one and a half of the CIR, and the EBS configuration is recommended to "0". The total bandwidth of the CBS and the EBS should be no less than the CIR/1000(bit). NodeB MMLCommand: SET LR. Huawei NodeB Configuration The VLAN priority of ARP packet is 1 by product default setting, which can be changed by command "SET INTBRDPARA". The DSCP and VLAN priority of DHCP & Tracert packet are 0 by product default setting, which can be changed by MML command. The DSCP of BFD packet is 56, and its VLAN priority is 7 by product default setting, which can be changed by command "STR IPCHK". In RNC sidethe recommended mode is to use ADD VLANID command to add IP VLAN mapping of the next hop one next hop one VLAN mapping. Signal Plane OAM OMIP The value of DSCP cites the recommendation DSCP in table 3. The recommendation DSCP changes it changes. Other For signal plane and user plane IP address(es), the recommended mode is just to use ADD VLANID command to add IP VLAN mapping of the next hop. Don't add vlan by ADD SCTPLNK/ADD IPPATH command. The FE/GE port work mode should be consulted with the peer device. Local Peer 1)100M/FULL 100M/FULL 2)1000M/FULL 1000M/FULL 3) AUTO AUTO The DSCP valueVLANIDVLAN Priority of IPPM packet is the same as corresponding IPPATH. User Plane 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 11 of 80 235388102.xlsx.ms_office SecurityFor Internal Table 5 Traffic type SIG IPPATH IPPATH IPPATH IPPATH Common Channel SNTP ARP Request ARP Reply 1588V2 OMCH active/standby control packet BFD IP CLK(V1 private) Ping(ICMP) ping(ICMP response) Tracert DHCP Ping MAC IPPM Note1 Note2 Note3 Note4 Note5 The DSCP Value or VLAN priority used in RAN should be planned in Transmission Device, and make sure the Transmission Device will not change the Values Note6 Table 6 VLAN priority The default map table between DSCP value and VLAN priority, can be modified by the command "SET DSCPMAP". Type DSCP VLAN priority 0~7 0 8~15 1 16~23 2 OM Value About the DSCP OMCH, the recommended configured mode is "OMHPRI=46, OMLPRI=18"("SET DIFPRI" command); means that the DSCP of some contol messages (eg:MML Command) is 46,and the DSCP of ordinary packets(such as log upload or software download) is 18. NoteFor 3G NodeBthe high DSCP of OM can not be equal to any other DSCP of service. The value of DSCP cites the recommendation DSCP in table 5. The recommendation DSCP changes it changes. The DSCP of CCH is the same with the DSCP of SIG. There are four types of traffic: User Data, SIG Data, Maintenance Data, and Other Data. Among which, the User Data is of different service levels according to the DSCP value. Each level will be mapped to the corresponding VLAN priority by using the default map table. The recommended vlan configured mode is to use Single VLAN, not VLAN GROUP. and the VLAN priority will accord to map table with DSCP value(refer to "Table 6") For example: ADD VLANMAP: NEXTHOPIP="x.x.x.x", MASK="255.255.255.255", VLANMODE=SINGLEVLAN, VLANID=YYY, SETPRIO=DISABLE; If the customer want to use "VLAN GROUP", please contact R&D to check it. "Single VLAN" mode is required in IPSec scenario. VLAN configuration Single VLAN Other User Data The ARP proxy switch is recommended to be closed. 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 12 of 80 235388102.xlsx.ms_office SecurityFor Internal 24~31 3 32~39 4 40~47 5 48~55 6 56~63 7 Value 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 13 of 80 235388102.xlsx.ms_office SecurityFor Internal Rx(kbps) DSCP IPPATH Ping Check 48 48 Physical Link BW 46 Enable Physical Link BW 34 Enable Physical Link BW 18 Enable Physical Link BW 10 Enable 46High 18Low The TRMMAP configuration can be added or modified by the command "ADD/MOD TRMMAP", unless the TRMMAP ID is from 0-13; If there is 2 to 6 queues in transmission, please refer to table 2 in sheet "IUB IP QoS". DSCP VLAN PriorityCommand DSCP(Command) 48 SET DSCPMAP ADD/MOD SCTPLNK 46 SET DSCPMAP ADD/MOD IPPATH+SET PHBMAP 34 SET DSCPMAP ADD/MOD IPPATH+SET PHBMAP 18 SET DSCPMAP ADD/MOD IPPATH+SET PHBMAP 10 SET DSCPMAP ADD/MOD IPPATH+SET PHBMAP 46High SET DSCPMAP Realized by M2000 server 18Low SET DSCPMAP Realized by M2000 server SET INTBRDPARA 0 SET DSCPMAP PING IP 0 SET DSCPMAP SET INTBRDPARA 0 SET DSCPMAP TRC IPADDR 56 SET DSCPMAP STR IPCHK "6" Huawei RNC Configuration Note 1: The FE/GE port work mode should be consulted with the peer device. Local Peer 1)100M/FULL 100M/FULL 2)1000M/FULL 1000M/FULL 3) AUTO AUTO The Physical Link BW is the minimum bandwidth of physical link connection between RNC and NodeB. It is recommended to set the value of parameter "IPPATH Ping Check Type" to "UDP". The recommended TRMMAP is not the default TRMMAP,please use the recommended TRMMAP. Refer to table 2 as following. Keeping the TRMMAP mapping relationship is preferred if the RNC is updated from old version. 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 14 of 80 235388102.xlsx.ms_office SecurityFor Internal same as corresponding IPPATH SET DSCPMAP ADD/MOD IPPATH+SET PHBMAP The DSCP Value or VLAN priority used in RAN should be planned in Transmission Device, and make sure the Transmission Device will not change the Values CIR:Committed Information Rate(bit/s); CBS:Committed Burst Size(bit); EBS:Excess Burst Size (bit); The CIR means the bandwidth of guarantee rate of the physical link. The CBS configuration is recommended to one and a half of the CIR, and the EBS configuration is recommended to "0". The total bandwidth of the CBS and the EBS should be no less than the CIR/1000(bit). NodeB MMLCommand: SET LR. Huawei NodeB Configuration The VLAN priority of ARP packet is 1 by product default setting, which can be changed by command "SET INTBRDPARA". The DSCP and VLAN priority of DHCP & Tracert packet are 0 by product default setting, which can be changed by MML command. The DSCP of BFD packet is 56, and its VLAN priority is 7 by product default setting, which can be changed by command "STR IPCHK". In RNC sidethe recommended mode is to use ADD VLANID command to add IP VLAN mapping of the next hop one next hop one VLAN mapping. The value of DSCP cites the recommendation DSCP in table 3. The recommendation DSCP changes it changes. For signal plane and user plane IP address(es), the recommended mode is just to use ADD VLANID command to add IP VLAN mapping of the next hop. Don't add vlan by ADD SCTPLNK/ADD IPPATH command. The FE/GE port work mode should be consulted with the peer device. Local Peer 1)100M/FULL 100M/FULL 2)1000M/FULL 1000M/FULL 3) AUTO AUTO The DSCP valueVLANIDVLAN Priority of IPPM packet is the same as corresponding IPPATH. 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 15 of 80 235388102.xlsx.ms_office SecurityFor Internal DSCP VLAN ID Command VLAN PriorityCommand 48 ADD VLANMAP "6"(Vary according to the DSCP) 46 ADD VLANMAP "5"(Vary according to the DSCP) 34 ADD VLANMAP "4"(Vary according to the DSCP) 18 ADD VLANMAP "2"(Vary according to the DSCP) 10 ADD VLANMAP "1"(Vary according to the DSCP) 48 ADD VLANMAP "6"(Vary according to the DSCP) 46High ADD VLANMAP "5"(Vary according to the DSCP) 18Low ADD VLANMAP "2"(Vary according to the DSCP) 46 ADD VLANMAP "5"(Vary according to the DSCP) ADD VLANMAP "7"(default) determined by ARP Request determined by ARP Request 46 ADD VLANMAP "5"(Vary according to the DSCP) 63 ADD VLANMAP "7"(Vary according to the DSCP) 56 ADD VLANMAP "7"(Vary according to the DSCP) 63 ADD VLANMAP "7"(default) / ADD VLANMAP "7"(Vary according to the DSCP) Refill ADD VLANMAP refilled according to the DSCP / ADD VLANMAP "7"(Vary according to the DSCP) 0 Learning "0"(default) ADD CFMMA "6"(configured) same as corresponding IPPATH same as corresponding IPPATH same as corresponding IPPATH The DSCP Value or VLAN priority used in RAN should be planned in Transmission Device, and make sure the Transmission Device will not change the Values The default map table between DSCP value and VLAN priority, can be modified by the command "SET DSCPMAP". About the DSCP OMCH, the recommended configured mode is "OMHPRI=46, OMLPRI=18"("SET DIFPRI" command); means that the DSCP of some contol messages (eg:MML Command) is 46,and the DSCP of ordinary packets(such as log upload or software download) is 18. NoteFor 3G NodeBthe high DSCP of OM can not be equal to any other DSCP of service. The value of DSCP cites the recommendation DSCP in table 5. The recommendation DSCP changes it changes. The DSCP of CCH is the same with the DSCP of SIG. There are four types of traffic: User Data, SIG Data, Maintenance Data, and Other Data. Among which, the User Data is of different service levels according to the DSCP value. Each level will be mapped to the corresponding VLAN priority by using the default map table. The recommended vlan configured mode is to use Single VLAN, not VLAN GROUP. and the VLAN priority will accord to map table with DSCP value(refer to "Table 6") For example: ADD VLANMAP: NEXTHOPIP="x.x.x.x", MASK="255.255.255.255", VLANMODE=SINGLEVLAN, VLANID=YYY, SETPRIO=DISABLE; If the customer want to use "VLAN GROUP", please contact R&D to check it. "Single VLAN" mode is required in IPSec scenario. The ARP proxy switch is recommended to be closed. 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 16 of 80 235388102.xlsx.ms_office SecurityFor Internal 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 17 of 80 235388102.xlsx.ms_office SecurityFor Internal IPPATH Ping Check Type UDP UDP UDP UDP 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 18 of 80 235388102.xlsx.ms_office SecurityFor Internal 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 19 of 80 235388102.xlsx.ms_office SecurityFor Internal DSCP(Command) SET DIFPRI(SIG) ADD IPPATH ADD IPPATH ADD IPPATH ADD IPPATH cite the DSCP value of SIG SET DIFPRI(OM) SET DIFPRI(OM) SET DIFPRI(OM) SET DIFPRI(PTP) NULL ADD BFDSESSION NULL NULL NULL TRACERT NULL same as corresponding IPPATH 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 20 of 80 235388102.xlsx.ms_office SecurityFor Internal Table 1 Tx(kbps) Rx(kbps) NCP CCP EF 1984 1984 AF41 1984 1984 AF21 1984 1984 AF11 1984 1984 Table 2 Tx(kbps) Rx(kbps) NCP CCP EF 3968 3968 AF41 3968 3968 AF21 3968 3968 AF11 3968 3968 Table 3 Tx(kbps) Rx(kbps) NCP CCP EF 5952 5952 AF41 5952 5952 AF21 5952 5952 AF11 5952 5952 Table 4 Tx(kbps) Rx(kbps) NCP CCP EF 7936 7936 AF41 7936 7936 AF21 7936 7936 AF11 7936 7936 Table 5 Tx(kbps) Rx(kbps) NCP CCP EF 9920 9920 AF41 9920 9920 Huawei RNC Configuration Scenario 1: MP 1*E1 Signal Plane Scenario 5: MP 5*E1 OAM OMIP User Plane Signal Plane User Plane User Plane User Plane User Plane Scenario 4: MP 4*E1 Signal Plane Scenario 2: MP 2*E1 Signal Plane Scenario 3: MP 3*E1 OAM OMIP OAM OMIP OAM OMIP Signal Plane 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 21 of 80 235388102.xlsx.ms_office SecurityFor Internal AF21 9920 9920 AF11 9920 9920 Table 6 Tx(kbps) Rx(kbps) NCP CCP EF 11904 11904 AF41 11904 11904 AF21 11904 11904 AF11 11904 11904 Table 7 Tx(kbps) Rx(kbps) NCP CCP EF 13888 13888 AF41 13888 13888 AF21 13888 13888 AF11 13888 13888 Table 8 Tx(kbps) Rx(kbps) NCP CCP EF 15872 15872 AF41 15872 15872 AF21 15872 15872 AF11 15872 15872 Table 9 Tx(kbps) Rx(kbps) NCP CCP EF 17856 17856 AF41 17856 17856 AF21 17856 17856 AF11 17856 17856 Table 10 Tx(kbps) Rx(kbps) Signal Plane Scenario 8: MP 8*E1 Signal Plane OAM OMIP OAM OMIP User Plane Scenario 7: MP 7*E1 User Plane Scenario 6: MP 6*E1 User Plane User Plane Signal Plane OAM OMIP OAM OMIP Scenario 9: MP 9*E1 Signal Plane User Plane OAM OMIP Scenario 10: MP 10*E1 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 22 of 80 235388102.xlsx.ms_office SecurityFor Internal NCP CCP EF 19840 19840 AF41 19840 19840 AF21 19840 19840 AF11 19840 19840 Table 11 Tx(kbps) Rx(kbps) NCP CCP EF 21824 21824 AF41 21824 21824 AF21 21824 21824 AF11 21824 21824 Table 12 Tx(kbps) Rx(kbps) NCP CCP EF 23808 23808 AF41 23808 23808 AF21 23808 23808 AF11 23808 23808 Note 1: TRMMAP Configuration Rules Interface Type Service Type PHB(default) PHB(recommanded) Iub Common channel primary PATH EF EF Iub IMS SRB primary PATH (IMS SRB) EF EF Iub SRB primary PATH (SRB) EF EF Iub HSDPA Signal primary PATH (SRB) EF EF Iub HSDPA IMS Signal primary PATH (IMS SRB) EF EF Iub HSUPA Signal primary PATH (SRB) EF EF Iub HSUPA IMS Signal primary PATH (IMS SRB) EF EF Iub AMR voice primary PATH EF EF Iub HSDPA Voice primary PATHAF43 AF41 Iub HSUPA Voice primary PATHAF43 AF41 Iub R99 CS conversational primary PATH AF43 AF41 Iub R99 PS conversational primary PATH AF43 AF41 Iub HSDPA conversational primary PATH AF43 AF41 Iub HSUPA conversational primary PATH AF43 AF41 Iub R99 CS streaming primary PATH AF43 AF41 Iub R99 PS streaming primary PATH AF43 AF41 Iub HSDPA streaming primary PATH AF43 AF41 The TRMMAP should be same with the sheet "FE",refer to the table as following User Plane OAM OMIP Scenario 12: MP 12*E1 Signal Plane User Plane OAM OMIP Signal Plane User Plane OAM OMIP Scenario 11: MP 11*E1 Signal Plane 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 23 of 80 235388102.xlsx.ms_office SecurityFor Internal Iub HSUPA streaming primary PATH AF43 AF41 Iub R99 PS high PRI interactive primary PATH AF23 AF21 Iub R99 PS middle PRI interactive primary PATH AF23 AF21 Iub R99 PS low PRI interactive primary PATH AF23 AF21 Iub R99 PS background primary PATH AF23 AF21 Iub HSDPA high PRI interactive primary PATH AF13 AF11 Iub HSDPA middle PRI interactive primary PATH AF13 AF11 Iub HSDPA low PRI interactive primary PATH AF13 AF11 Iub HSUPA high PRI interactive primary PATH AF13 AF11 Iub HSUPA middle PRI interactive primary PATH AF13 AF11 Iub HSUPA low PRI interactive primary PATH AF13 AF11 Iub HSDPA background primary PATH AF13 AF11 Iub HSUPA background primary PATH AF13 AF11 The TRMMAP configuration can be added or modified by the command "ADD/MOD TRMMAP", unless the TRMMAP ID is from 0-13 ; Table 13 DSCP NCP 48 CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46 18 Table 14 DSCP NCP 48 CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46 18 Table 15 DSCP NCP 48 CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46 18 Table 16 DSCP NCP 48 Signal Plane OMIP OAM OMIP Scenario 1: MP 1*E1 User Plane Scenario 2: MP 2*E1 Signal Plane Scenario 3: MP 3*E1 Signal Plane User Plane Huawei NodeB Configuration User Plane Scenario 4: MP 4*E1 OMIP OAM OAM Signal Plane 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 24 of 80 235388102.xlsx.ms_office SecurityFor Internal CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46 18 Table 17 DSCP NCP 48 CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46 18 Table 18 DSCP NCP 48 CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46 18 Table 19 DSCP NCP 48 CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46 18 Table 20 DSCP NCP 48 CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46 18 Signal Plane OAM OMIP User Plane Signal Plane User Plane User Plane Scenario 8: MP 8*E1 OAM OMIP OAM OMIP Signal Plane Signal Plane Scenario 5: MP 5*E1 User Plane OAM OMIP User Plane Scenario 6: MP 6*E1 OAM OMIP Signal Plane Scenario 7: MP 7*E1 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 25 of 80 235388102.xlsx.ms_office SecurityFor Internal Table 21 DSCP NCP 48 CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46 18 Table 22 DSCP NCP 48 CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46 18 Table 23 DSCP NCP 48 CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46 18 Table 24 DSCP NCP 48 CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46 18 Scenario 12: MP 12*E1 Signal Plane User Plane OAM OMIP Scenario 11: MP 11*E1 Signal Plane User Plane OAM OMIP Scenario 10: MP 10*E1 Signal Plane User Plane OAM OMIP Signal Plane User Plane OAM OMIP Scenario 9: MP 9*E1 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 26 of 80 235388102.xlsx.ms_office SecurityFor Internal DSCP IPPATH Ping Check IPPATH Ping Check Type 48 48 46 Enable UDP 34 Enable UDP 18 Enable UDP 10 Enable UDP 46 18 DSCP IPPATH Ping Check IPPATH Ping Check Type 48 48 46 Enable UDP 34 Enable UDP 18 Enable UDP 10 Enable UDP 46 18 DSCP IPPATH Ping Check IPPATH Ping Check Type 48 48 46 Enable UDP 34 Enable UDP 18 Enable UDP 10 Enable UDP 46 18 DSCP IPPATH Ping Check IPPATH Ping Check Type 48 48 46 Enable UDP 34 Enable UDP 18 Enable UDP 10 Enable UDP 46 18 DSCP IPPATH Ping Check IPPATH Ping Check Type 48 48 46 Enable UDP 34 Enable UDP Huawei RNC Configuration 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 27 of 80 235388102.xlsx.ms_office SecurityFor Internal 18 Enable UDP 10 Enable UDP 46 18 DSCP IPPATH Ping Check IPPATH Ping Check Type 48 48 46 Enable UDP 34 Enable UDP 18 Enable UDP 10 Enable UDP 46 18 DSCP IPPATH Ping Check IPPATH Ping Check Type 48 48 46 Enable UDP 34 Enable UDP 18 Enable UDP 10 Enable UDP 46 18 DSCP IPPATH Ping Check IPPATH Ping Check Type 48 48 46 Enable UDP 34 Enable UDP 18 Enable UDP 10 Enable UDP 46 18 DSCP IPPATH Ping Check IPPATH Ping Check Type 48 48 46 Enable UDP 34 Enable UDP 18 Enable UDP 10 Enable UDP 46 18 DSCP IPPATH Ping Check IPPATH Ping Check Type 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 28 of 80 235388102.xlsx.ms_office SecurityFor Internal 48 48 46 Enable UDP 34 Enable UDP 18 Enable UDP 10 Enable UDP 46 18 DSCP IPPATH Ping Check IPPATH Ping Check Type 48 48 46 Enable UDP 34 Enable UDP 18 Enable UDP 10 Enable UDP 46 18 DSCP IPPATH Ping Check IPPATH Ping Check Type 48 48 46 Enable UDP 34 Enable UDP 18 Enable UDP 10 Enable UDP 46 18 The TRMMAP should be same with the sheet "FE",refer to the table as following 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 29 of 80 235388102.xlsx.ms_office SecurityFor Internal The TRMMAP configuration can be added or modified by the command "ADD/MOD TRMMAP", unless the TRMMAP ID is from 0-13 ; Huawei NodeB Configuration 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 30 of 80 235388102.xlsx.ms_office SecurityFor Internal Table 1 Tx(kbps) Rx(kbps) NCP CCP EF 768 768 AF41 768 768 AF21 768 768 AF11 768 768 Table 2 Tx(kbps) Rx(kbps) NCP CCP EF 960 960 AF41 960 960 AF21 960 960 AF11 960 960 Table 3 Tx(kbps) Rx(kbps) NCP CCP EF 1408 1408 AF41 1408 1408 AF21 1408 1408 AF11 1408 1408 Table 4 Tx(kbps) Rx(kbps) NCP CCP EF 1536 1536 AF41 1536 1536 AF21 1536 1536 AF11 1536 1536 Table 5 Tx(kbps) Rx(kbps) NCP CCP EF 1984 1984 AF41 1984 1984 Huawei RNC Configuration Signal Plane Scenario 1: PPP 12TS Signal Plane Scenario 2: PPP 15TS User Plane OAM OMIP OAM OMIP OAM OMIP Signal Plane Scenario 3: PPP 22TS User Plane Signal Plane User Plane User Plane Scenario 4: PPP 24TS Signal Plane Scenario 5: PPP 1*E1 OAM OMIP User Plane 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 31 of 80 235388102.xlsx.ms_office SecurityFor Internal AF21 1984 1984 AF11 1984 1984 Note 1: TRMMAP Configuration Rules Interface Type Service Type PHB(default) PHB(recommanded) Iub Common channel primary PATH EF EF Iub IMS SRB primary PATH (IMS SRB) EF EF Iub SRB primary PATH (SRB) EF EF Iub HSDPA Signal primary PATH (SRB) EF EF Iub HSDPA IMS Signal primary PATH (IMS SRB) EF EF Iub HSUPA Signal primary PATH (SRB) EF EF Iub HSUPA IMS Signal primary PATH (IMS SRB) EF EF Iub AMR voice primary PATH EF EF Iub HSDPA Voice primary PATH AF43 AF41 Iub HSUPA Voice primary PATH AF43 AF41 Iub R99 CS conversational primary PATH AF43 AF41 Iub R99 PS conversational primary PATH AF43 AF41 Iub HSDPA conversational primary PATH AF43 AF41 Iub HSUPA conversational primary PATH AF43 AF41 Iub R99 CS streaming primary PATHAF43 AF41 Iub R99 PS streaming primary PATHAF43 AF41 Iub HSDPA streaming primary PATHAF43 AF41 Iub HSUPA streaming primary PATHAF43 AF41 Iub R99 PS high PRI interactive primary PATH AF23 AF21 Iub R99 PS middle PRI interactive primary PATH AF23 AF21 Iub R99 PS low PRI interactive primary PATH AF23 AF21 Iub R99 PS background primary PATH AF23 AF21 Iub HSDPA high PRI interactive primary PATH AF13 AF11 Iub HSDPA middle PRI interactive primary PATH AF13 AF11 Iub HSDPA low PRI interactive primary PATH AF13 AF11 Iub HSUPA high PRI interactive primary PATH AF13 AF11 Iub HSUPA middle PRI interactive primary PATH AF13 AF11 Iub HSUPA low PRI interactive primary PATH AF13 AF11 Iub HSDPA background primary PATH AF13 AF11 Iub HSUPA background primary PATH AF13 AF11 The TRMMAP configuration can be added or modified by the command "ADD/MOD TRMMAP", unless the TRMMAP ID is from 0-13 ; Table 7 DSCP NCP 48 CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46 18 Scenario 1: PPP 12TS Signal Plane The TRMMAP should be same with the sheet "FE" User Plane OAM OMIP OAM OMIP Huawei NodeB Configuration User Plane 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 32 of 80 235388102.xlsx.ms_office SecurityFor Internal Table 8 DSCP NCP 48 CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46 18 Table 9 DSCP NCP 48 CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46 18 Table 10 DSCP NCP 48 CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46 18 Table 11 DSCP NCP 48 CCP 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46 18 User Plane Signal Plane Scenario 2: PPP 15TS OAM OMIP User Plane Signal Plane Scenario 3: PPP 22TS Signal Plane OAM OMIP Scenario 5: PPP 1*E1 OAM OMIP OAM OMIP Signal Plane User Plane User Plane Scenario 4: PPP 24TS 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 33 of 80 235388102.xlsx.ms_office SecurityFor Internal DSCP IPPATH Ping Check IPPATH Ping Check Type 48 48 46 Enable UDP 34 Enable UDP 18 Enable UDP 10 Enable UDP 46 18 DSCP IPPATH Ping Check IPPATH Ping Check Type 48 48 46 Enable UDP 34 Enable UDP 18 Enable UDP 10 Enable UDP 46 18 DSCP IPPATH Ping Check IPPATH Ping Check Type 48 48 46 Enable UDP 34 Enable UDP 18 Enable UDP 10 Enable UDP 46 18 DSCP IPPATH Ping Check IPPATH Ping Check Type 48 48 46 Enable UDP 34 Enable UDP 18 Enable UDP 10 Enable UDP 46 18 DSCP IPPATH Ping Check IPPATH Ping Check Type 48 48 46 Enable UDP 34 Enable UDP Huawei RNC Configuration 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 34 of 80 235388102.xlsx.ms_office SecurityFor Internal 18 Enable UDP 10 Enable UDP 46 18 The TRMMAP configuration can be added or modified by the command "ADD/MOD TRMMAP", unless the TRMMAP ID is from 0-13 ; Huawei NodeB Configuration 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 35 of 80 235388102.xlsx.ms_office SecurityFor Internal Table 1 Tx(kbps) NCP CCP EF Physical Link BW LQ_EF Physical Link BW AF41 Physical Link BW LQ_AF41 Physical Link BW AF21 Physical Link BW LQ_AF21 Physical Link BW AF11 Physical Link BW LQ_AF11 Physical Link BW Note 1: Note2: Note 3: Note 4: TRMMAP Configuration Rules Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub The recommended TRMMAP is not the default TRMMAP,please use the recommended TRMMAP. Refer to table as following. Interface Type R99 PS conversational primary PATH HSDPA conversational primary PATH HSUPA conversational primary PATH R99 CS streaming primary PATH AMR voice primary PATH HSDPA Voice primary PATH HSUPA Voice primary PATH R99 CS conversational primary PATH IMS SRB primary PATH (IMS SRB) SRB primary PATH (SRB) HSDPA Signal primary PATH (SRB) HSDPA IMS Signal primary PATH (IMS SRB) HSUPA Signal primary PATH (SRB) Huawei RNC Configuration Scenario 1: MP+FE Signal Plane The Physical Link BW is the minimum bandwidth of physical link connection between RNC and NodeB. LQ_ means Low QoS. The FE/GE port work mode should be consulted with the peer device. Local Peer 1)100M/FULL 100M/FULL 2)1000M/FULL 1000M/FULL 3) AUTO AUTO Service Type Common channel primary PATH HSUPA IMS Signal primary PATH (IMS SRB) User Plane OAM OMIP 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 36 of 80 235388102.xlsx.ms_office SecurityFor Internal Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Table 2 Table 3 ATM: FE: The FE configuration is as follows (the signal plane is carried on ATM): Tx(kbps) EF Physical Link BW AF41 Physical Link BW AF21 Physical Link BW AF11 Physical Link BW Note 1: Note 2: HSUPA middle PRI interactive primary PATH HSUPA low PRI interactive primary PATH HSDPA background primary PATH HSUPA background primary PATH R99 PS background primary PATH HSDPA high PRI interactive primary PATH HSDPA middle PRI interactive primary PATH HSDPA low PRI interactive primary PATH HSUPA high PRI interactive primary PATH HSDPA streaming primary PATH HSUPA streaming primary PATH R99 PS high PRI interactive primary PATH R99 PS middle PRI interactive primary PATH R99 PS low PRI interactive primary PATH R99 PS streaming primary PATH The ATM configuration refer to the "Iub Tx Configuration Recommendation_ATM". But the control plane bandwidth should be enlarged. The rule is: 4E1 control plane bandwidth configuration of ATM is recommended in 1E1+ FE scenario. 6E1 control plane bandwidth configuration of ATM is recommended in 2E1+ FE scenario 8E1 control plane bandwidth configuration of ATM is recommended in 3~8E1+FE scenario. The AAL2 user plane bandwidth should be caculated according to the actual E1 number of muti-E1 sheet in Iub Tx Configuration Recommendation_ATM . Signal Plane The Physical Link BW is the minimum bandwidth of physical link connection between RNC and NodeB. The FE/GE port work mode should be consulted with the peer device. Local Peer 1)100M/FULL 100M/FULL 2)1000/FULL 1000M/FULL 3) AUTO AUTO OMIP Scenario 2ATM+FE VLAN configuration only for FE User Plane OAM 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 37 of 80 235388102.xlsx.ms_office SecurityFor Internal Note 3: TRMMAP Configuration Rules Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Iub Table 4 Table 5 DSCP NCP 48 CCP 48 IPPATH 46 HSUPA middle PRI interactive primary PATH HSUPA low PRI interactive primary PATH HSDPA background primary PATH HSUPA background primary PATH The recommended TRMMAP is not the default TRMMAP,please use the recommended TRMMAP. Refer to table as following. Interface Type R99 PS background primary PATH HSDPA high PRI interactive primary PATH HSDPA middle PRI interactive primary PATH HSDPA low PRI interactive primary PATH HSUPA high PRI interactive primary PATH HSDPA streaming primary PATH HSUPA streaming primary PATH R99 PS high PRI interactive primary PATH R99 PS middle PRI interactive primary PATH R99 PS low PRI interactive primary PATH R99 PS conversational primary PATH HSDPA conversational primary PATH HSUPA conversational primary PATH R99 CS streaming primary PATH R99 PS streaming primary PATH HSUPA IMS Signal primary PATH (IMS SRB) AMR voice primary PATH HSDPA Voice primary PATH HSUPA Voice primary PATH R99 CS conversational primary PATH IMS SRB primary PATH (IMS SRB) SRB primary PATH (SRB) HSDPA Signal primary PATH (SRB) HSDPA IMS Signal primary PATH (IMS SRB) HSUPA Signal primary PATH (SRB) Service Type Common channel primary PATH Signal Plane User Plane Huawei NodeB Configuration VLAN configuration Scenario 1: MP+FE 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 38 of 80 235388102.xlsx.ms_office SecurityFor Internal IPPATH 46 IPPATH 34 IPPATH 34 IPPATH 18 IPPATH 18 IPPATH 10 IPPATH 10 46(High level) 18(Low level) Note1: Table 6 Table 7 ATM: FE: The FE configuration is as follows (the signal plane is carried on ATM): DSCP 48 48 IPPATH 46 IPPATH 34 IPPATH 18 IPPATH 10 46(High level) 18(Low level) Note1: Table 8 Traffic type SIG IPPATH IPPATH IPPATH IPPATH The ATM configuration refer to the "Iub Tx Configuration Recommendation_ATM". But the control plane bandwidth should be enlarged. The rule is: 4E1 control plane bandwidth configuration of ATM is recommended in 1E1+ FE scenario. 6E1 control plane bandwidth configuration of ATM is recommended in 2E1+ FE scenario 8E1 control plane bandwidth configuration of ATM is recommended in 3~8E1+FE scenario. The AAL2 user plane bandwidth should be caculated according to the actual E1 number of muti-E1 sheet in Iub Tx Configuration Recommendation_ATM . Scenario 2ATM+FE User Plane VLAN configuration (Scenario 1) The FE/GE port work mode should be consulted with the peer device. Local Peer 1)100M/FULL 100M/FULL 2)1000M/FULL 1000M/FULL 3) AUTO AUTO VLAN configuration (Scenario 2) VLAN GROUP The FE/GE port work mode should be consulted with the peer device. Local Peer 1)100M/FULL 100M/FULL 2)1000M/FULL 1000M/FULL 3) AUTO AUTO User Data OM OMIP OAM OMIP Signal Plane User Plane 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 39 of 80 235388102.xlsx.ms_office SecurityFor Internal Common channel Other Note1 Note2 Note3 Note4 (3)The DSCP Value or VLAN priority used in RAN should be planned in Transmission Device, and make sure the Transmission Device will not change the Values Note6: The default map table between DSCP value and VLAN priority, can be modified by the command "SET DSCPMAP". Type DSCP VLAN priority 0~7 0 8~15 1 16~23 2 24~31 3 32~39 4 40~47 5 48~55 6 56~63 7 Value The recommended vlan configured mode is to use Single VLAN, not VLAN GROUP. and the VLAN priority will accord to map table with DSCP value(refer to "Table 6") For example: ADD VLANMAP: NEXTHOPIP="x.x.x.x", MASK="255.255.255.255", VLANMODE=SINGLEVLAN, VLANID=YYY, SETPRIO=DISABLE; If the customer want to use "VLAN GROUP", please contact R&D to check it. "Single VLAN" mode is required in IPSec scenario. The User Data is of different service levels according to the DSCP value. Each level corresponds to different VLAN setting using the default map table.. VLAN GROUP User Data OM (1)The DSCP of CCH is same with the DSCP of SIG. Using SET DIFPRI command to set DSCP value. (2) Needn't add vlan tag for SIG which bearing in ATM. The value of DSCP cites the recommendation DSCP in table 7. The recommendation DSCP changes it changes. 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 40 of 80 235388102.xlsx.ms_office SecurityFor Internal Rx(kbps) DSCP Bear link 48 MP 48 MP Physical Link BW 46 MP Physical Link BW 46 FE Physical Link BW 34 MP Physical Link BW 34 FE Physical Link BW 18 MP Physical Link BW 18 FE Physical Link BW 10 MP Physical Link BW 10 FE 46(High level) 18(Low level) Primary Secondary Primary EF LQ_EF EF EF LQ_EF EF EF LQ_EF EF EF LQ_EF EF EF LQ_EF EF EF LQ_EF EF EF LQ_EF EF EF LQ_EF EF AF43 LQ_AF43 AF41 AF43 LQ_AF43 AF41 AF43 LQ_AF43 AF41 AF43 LQ_AF43 AF41 AF43 LQ_AF43 AF41 AF43 LQ_AF43 AF41 AF43 LQ_AF43 AF41 The recommended TRMMAP is not the default TRMMAP,please use the recommended TRMMAP. Refer to table as following. Huawei RNC Configuration The Physical Link BW is the minimum bandwidth of physical link connection between RNC and NodeB. LQ_ means Low QoS. The FE/GE port work mode should be consulted with the peer device. Local Peer 1)100M/FULL 100M/FULL 2)1000M/FULL 1000M/FULL 3) AUTO AUTO PHB(default) PHB(recommanded) MP 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 41 of 80 235388102.xlsx.ms_office SecurityFor Internal AF43 LQ_AF43 AF41 AF43 LQ_AF43 AF41 AF43 LQ_AF43 AF41 AF23 LQ_AF23 AF21 AF23 LQ_AF23 AF21 AF23 LQ_AF23 AF21 AF23 LQ_AF23 AF21 LQ_AF13 AF13 LQ_AF11 LQ_AF13 AF13 LQ_AF11 LQ_AF13 AF13 LQ_AF11 LQ_AF13 AF13 LQ_AF11 LQ_AF13 AF13 LQ_AF11 LQ_AF13 AF13 LQ_AF11 LQ_AF13 AF13 LQ_AF11 LQ_AF13 AF13 LQ_AF11 Rx(kbps) DSCP Bear link Physical Link BW 46 FE Physical Link BW 34 FE Physical Link BW 18 FE Physical Link BW 10 FE 46 FE 18 FE The ATM configuration refer to the "Iub Tx Configuration Recommendation_ATM". But the control plane bandwidth should be enlarged. The rule is: 4E1 control plane bandwidth configuration of ATM is recommended in 1E1+ FE scenario. 6E1 control plane bandwidth configuration of ATM is recommended in 2E1+ FE scenario 8E1 control plane bandwidth configuration of ATM is recommended in 3~8E1+FE scenario. The AAL2 user plane bandwidth should be caculated according to the actual E1 number of muti-E1 sheet in Iub Tx Configuration Recommendation_ATM . The Physical Link BW is the minimum bandwidth of physical link connection between RNC and NodeB. The FE/GE port work mode should be consulted with the peer device. Local Peer 1)100M/FULL 100M/FULL 2)1000/FULL 1000M/FULL 3) AUTO AUTO 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 42 of 80 235388102.xlsx.ms_office SecurityFor Internal Primary Secondary Primary RT_VBR EF RT_VBR RT_VBR EF RT_VBR RT_VBR EF RT_VBR RT_VBR EF RT_VBR RT_VBR EF RT_VBR RT_VBR EF RT_VBR RT_VBR EF RT_VBR RT_VBR EF RT_VBR RT_VBR AF43 RT_VBR RT_VBR AF43 RT_VBR RT_VBR AF43 RT_VBR RT_VBR AF43 RT_VBR RT_VBR AF43 RT_VBR RT_VBR AF43 RT_VBR RT_VBR AF43 RT_VBR RT_VBR AF43 RT_VBR RT_VBR AF43 RT_VBR RT_VBR AF43 RT_VBR NRT_VBR AF23 NRT_VBR NRT_VBR AF23 NRT_VBR NRT_VBR AF23 NRT_VBR NRT_VBR AF23 NRT_VBR AF13 UBR AF11 AF13 UBR AF11 AF13 UBR AF11 AF13 UBR AF11 AF13 UBR AF11 AF13 UBR AF11 AF13 UBR AF11 AF13 UBR AF11 The recommended TRMMAP is not the default TRMMAP,please use the recommended TRMMAP. Refer to table as following. PHB(default) PHB(recommanded) Huawei NodeB Configuration 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 43 of 80 235388102.xlsx.ms_office SecurityFor Internal DSCP VLAN ID Command VLAN PriorityCommand 48 46 ADD VLANMAP "5"(Vary according to the DSCP) 34 ADD VLANMAP "4"(Vary according to the DSCP) 18 ADD VLANMAP "2"(Vary according to the DSCP) 10 ADD VLANMAP "1"(Vary according to the DSCP) The ATM configuration refer to the "Iub Tx Configuration Recommendation_ATM". But the control plane bandwidth should be enlarged. The rule is: 4E1 control plane bandwidth configuration of ATM is recommended in 1E1+ FE scenario. 6E1 control plane bandwidth configuration of ATM is recommended in 2E1+ FE scenario 8E1 control plane bandwidth configuration of ATM is recommended in 3~8E1+FE scenario. The AAL2 user plane bandwidth should be caculated according to the actual E1 number of muti-E1 sheet in Iub Tx Configuration Recommendation_ATM . The FE/GE port work mode should be consulted with the peer device. Local Peer 1)100M/FULL 100M/FULL 2)1000M/FULL 1000M/FULL 3) AUTO AUTO The FE/GE port work mode should be consulted with the peer device. Local Peer 1)100M/FULL 100M/FULL 2)1000M/FULL 1000M/FULL 3) AUTO AUTO 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 44 of 80 235388102.xlsx.ms_office SecurityFor Internal 48 ADD VLANMAP "6"(Vary according to the DSCP) 46(High level) ADD VLANMAP "5"(Vary according to the DSCP) 18(Low level) ADD VLANMAP "2"(Vary according to the DSCP) ADD VLANMAP NULL (3)The DSCP Value or VLAN priority used in RAN should be planned in Transmission Device, and make sure the Transmission Device will not change the Values The default map table between DSCP value and VLAN priority, can be modified by the command "SET DSCPMAP". The recommended vlan configured mode is to use Single VLAN, not VLAN GROUP. and the VLAN priority will accord to map table with DSCP value(refer to "Table 6") For example: ADD VLANMAP: NEXTHOPIP="x.x.x.x", MASK="255.255.255.255", VLANMODE=SINGLEVLAN, VLANID=YYY, SETPRIO=DISABLE; If the customer want to use "VLAN GROUP", please contact R&D to check it. "Single VLAN" mode is required in IPSec scenario. The User Data is of different service levels according to the DSCP value. Each level corresponds to different VLAN setting using the default map table.. (1)The DSCP of CCH is same with the DSCP of SIG. Using SET DIFPRI command to set DSCP value. (2) Needn't add vlan tag for SIG which bearing in ATM. The value of DSCP cites the recommendation DSCP in table 7. The recommendation DSCP changes it changes. 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 45 of 80 235388102.xlsx.ms_office SecurityFor Internal IPPATH Ping Check IPPATH Ping Check Enable UDP Enable UDP Enable UDP Enable UDP Enable UDP Enable UDP Enable UDP Enable UDP Secondary LQ_EF LQ_EF LQ_EF LQ_EF LQ_EF LQ_EF LQ_EF LQ_EF LQ_AF41 LQ_AF41 LQ_AF41 LQ_AF41 LQ_AF41 LQ_AF41 LQ_AF41 PHB(recommanded) 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 46 of 80 235388102.xlsx.ms_office SecurityFor Internal LQ_AF41 LQ_AF41 LQ_AF41 LQ_AF21 LQ_AF21 LQ_AF21 LQ_AF21 AF11 AF11 AF11 AF11 AF11 AF11 AF11 AF11 DSCP(Command) IPPATH Ping Check IPPATH Ping Check Type ADD/MOD IPPATH+SET PHBMAP Enable UDP ADD/MOD IPPATH+SET PHBMAP Enable UDP ADD/MOD IPPATH+SET PHBMAP Enable UDP ADD/MOD IPPATH+SET PHBMAP Enable UDP Realized by M2000 server Realized by M2000 server 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 47 of 80 235388102.xlsx.ms_office SecurityFor Internal Secondary EF EF EF EF EF EF EF EF AF41 AF41 AF41 AF41 AF41 AF41 AF41 AF41 AF41 AF41 AF21 AF21 AF21 AF21 UBR UBR UBR UBR UBR UBR UBR UBR PHB(recommanded) 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 48 of 80 235388102.xlsx.ms_office SecurityFor Internal DSCP(Command) SET DIFPRI(SIG) ADD IPPATH ADD IPPATH ADD IPPATH ADD IPPATH 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 49 of 80 235388102.xlsx.ms_office SecurityFor Internal cite the DSCP value of SIG NULL SET DIFPRI(OM) 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 50 of 80 235388102.xlsx.ms_office 1. IPPOOL scenario is supported in RAN15.0. IPPATH is also supported. We often use "DEVIP" as the SIP address in IPPOOL. Note 2: When the planning number of IP addresses on Control Plane is more than 1 in Iu/IuR interface, the dual homing is recommended in SCTP link. Note 3: A policy-based route based on the source IP address must be added in IP POOL scenario. Policy-based routing is a technology that forwards packets based on pre-defined policies. Note 4: At most 16 IPPOOLs can be configured in a RNC. License is not needed when there is only one SIP adddress in the IPPOOL. Note 5: Adding a SIP address on another GE Port is preferred when capacity expansion. The second choice is adding board. IP LOGICPORT can be only used in RAN15.1, but can't in RAN15.0 in IPPOOL scenario. Note 7: 2. The recommended topology of network in L3 scenario. 3. The recommended topology of network in L2 scenario.(RAN15.1 only) Huawei RNC ConfigurationIP POOL support only Note 1 It's recommended to use "ETHIP", to connect with transmission device. Note 6: The FE/GE port work mode should be consulted with the peer device. 100M mode is not allowed to use. Local Peer 1)1000M/FULL 1000M/FULL 2) AUTO AUTO 6/23/2014 , 5180 235388102.xlsx.ms_office Table1 Tx(kbps) Rx(kbps) NCP CCP User Plane ADJNODE Physical Link BW Physical Link BW There is no need to configure the bandwidth of NCP and CCP links. The Physical Link BW is the minimum bandwidth of physical link connection between RNC and NodeB. Note 3: The value of signaling data can be set by command "ADD SCTPLNK" or "MOD SCTPLNK". The recommended value is 48. Note 4: In RAN15.0, when the function "IPPATH PING" is enabled, the type of "IPPATH PING" is "UDP" in Iub interface, and "ICMP" in Iu/Iur interface. The recommended TRMMAP is not the default TRMMAP,please use the recommended TRMMAP. Refer to table 2 as following. Table2 TRMMAP Configuration Rules The TRMMAP configuration can be added or modified by the command "ADD/MOD TRMMAP", unless the TRMMAP ID is from 0-13 ; If there is 2 to 6 queues in transmission, please refer to table 2 in sheet "IUB IP QoS". Table 3 Traffic type VLAN ID Command DSCP Sig ADD VLANID 48 User Data ADD VLANID / 46High 18Low ARP ICMP(manual) 0 DHCP 0 Tracert 0 BFD 56 PING MAC ADD CFMMA IPPM same as corresponding IPPATH same as corresponding IPPATH Note1 Note2 Note3 Note4 Signal Plane OAM OMIP Note 1: Note 2: VLAN configuration OM ADD VLANID Other ADD VLANID In RNC sidethe recommended mode is to use ADD VLANID command to add IP VLAN mapping of the next hop one next hop one VLAN mapping. For signal plane and user plane IP address(es), the recommended mode is just to use ADD VLANID command to add IP VLAN mapping of the next hop. Don't add vlan by The value of DSCP cites the recommendation DSCP in table 1. The recommendation DSCP changes, it changes. The default DSCP value of BFD packet is 56. It can be changed by command "STR IPCHK". 6/23/2014 , 5280 235388102.xlsx.ms_office Note5: The DSCP Value or VLAN priority used in RAN should be planned in Transmission Device, and make sure the Transmission Device will not change the Values Note6: It's recommended to active the IPPM connections in NodeB side by command "ACT IPPOOLPM" on RNC. So the DSCP value of IPPM links are the same as in RNC side. Table 1 DSCP NCP 48 CCP 48 46High 18Low Note 1: Note 2: Note 3: Note 4: Table 2 Tx(kbps) Rx(kbps) NCP CCP IPPATH Physical Link BW Physical Link BW IPPATH Physical Link BW Physical Link BW IPPATH Physical Link BW Physical Link BW IPPATH Physical Link BW Physical Link BW Note 1: Note 2: Note 3: Note 4: Huawei NodeB Configuration End Point scenario Signal Plane OAM OMIP It's recommended to set flow control switch to "BW_SHAPING_ONOFF_TOGGLE" on NodeB in IPPOOL scenario. The FE/GE port work mode should be consulted with the peer device. Local Peer 1)100M/FULL 100M/FULL 2)1000M/FULL 1000M/FULL 3) AUTO AUTO CIR:Committed Information Rate(bit/s); CBS:Committed Burst Size(bit); EBS:Excess Burst Size (bit); The CIR means the bandwidth of guarantee rate of the physical link. The CBS configuration is recommended to one and a half of the CIR, and the EBS configuration is recommended to "0". The total bandwidth of the CBS and the EBS should be no less than the CIR/1000(bit). NodeB MMLCommand: ADD IPPATH or SET LR. The Physical Link BW is the minimum bandwidth of physical link connection between RNC and NodeB. User Plane OAM OMIP Don't set the destination ip address to 0.0.0.0 in command "ADD IPRT". Don't set the destination ip address to 0.0.0.0 in command "ADD IPRT". It's recommended to configure "End Point" mode in IPPOOL scenario. The FE/GE port work mode should be consulted with the peer device. Local Peer 1)100M/FULL 100M/FULL 2)1000M/FULL 1000M/FULL 3) AUTO AUTO updating scenario with IPPATH Signal Plane 6/23/2014 , 5380 235388102.xlsx.ms_office Table 3 Traffic type DSCP SIG 48 User Data Common Channel 48 46High 18Low SNTP 46 ARP Request ARP Reply 1588V2 46 OMCH active/standby control packet 63 BFD 56 IP CLK(V1 private) 63 Ping(ICMP) / ping(ICMP response) Refill Tracert / DHCP 0 Ping MAC Note1 Note2 Note3 Note4 Note5 The DSCP Value or VLAN priority used in RAN should be planned in Transmission Device, and make sure the Transmission Device will not change the Values Table 4 VLAN priority The default map table between DSCP value and VLAN priority, can be modified by the command "SET DSCPMAP". Type DSCP VLAN priority 0~7 0 8~15 1 16~23 2 24~31 3 32~39 4 40~47 5 48~55 6 56~63 7 The DSCP of CCH is the same with the DSCP of SIG. About the DSCP OMCH, the recommended configured mode is "OMHPRI=46, OMLPRI=18"("SET DIFPRI" command); means that the DSCP of some contol messages (eg:MML Command) is 46,and the DSCP of ordinary packets(such as log upload or software download) is 18. NoteFor 3G NodeBthe high DSCP of OM can not be equal to any other DSCP Value VLAN configuration Single VLAN OM Other The recommended vlan configured mode is to use Single VLAN, not VLAN GROUP. and the VLAN priority will accord to map table with DSCP value. For example: ADD VLANMAP: NEXTHOPIP="x.x.x.x", MASK="255.255.255.255", VLANMODE=SINGLEVLAN, VLANID=YYY, SETPRIO=DISABLE; If the customer want to use "VLAN GROUP", please contact R&D to check it. "Single VLAN" mode is required in IPSec scenario. There are four types of traffic: User Data, SIG Data, Maintenance Data, and Other Data. Among which, the User Data is of different service levels according to the DSCP value. Each level will be mapped to the corresponding VLAN priority by using the default map table. The value of DSCP cites the recommendation DSCP in table 3. The recommendation DSCP changes it changes. 6/23/2014 , 5480 235388102.xlsx.ms_office When the planning number of IP addresses on Control Plane is more than 1 in Iu/IuR interface, the dual homing is recommended in SCTP link. A policy-based route based on the source IP address must be added in IP POOL scenario. Policy-based routing is a technology that forwards packets based on pre-defined policies. At most 16 IPPOOLs can be configured in a RNC. License is not needed when there is only one SIP adddress in the IPPOOL. Adding a SIP address on another GE Port is preferred when capacity expansion. The second choice is adding board. Huawei RNC ConfigurationIP POOL support only It's recommended to use "ETHIP", to connect with transmission device. The FE/GE port work mode should be consulted with the peer device. 100M mode is not allowed to use. Local Peer 1)1000M/FULL 1000M/FULL 2) AUTO AUTO 6/23/2014 , 5580 235388102.xlsx.ms_office DSCP IPPATH Ping Check 48 48 / Enable 46High 18Low The Physical Link BW is the minimum bandwidth of physical link connection between RNC and NodeB. The value of signaling data can be set by command "ADD SCTPLNK" or "MOD SCTPLNK". The recommended value is 48. In RAN15.0, when the function "IPPATH PING" is enabled, the type of "IPPATH PING" is "UDP" in Iub interface, and "ICMP" in Iu/Iur interface. The recommended TRMMAP is not the default TRMMAP,please use the recommended TRMMAP. Refer to table 2 as following. The TRMMAP configuration can be added or modified by the command "ADD/MOD TRMMAP", unless the TRMMAP ID is from 0-13 ; VLAN PriorityCommand DSCP(Command) SET DSCPMAP ADD/MOD SCTPLNK SET DSCPMAP ADD/MOD IPPATH+SET PHBMAP SET DSCPMAP Realized by M2000 server SET DSCPMAP Realized by M2000 server SET INTBRDPARA SET DSCPMAP PING IP SET DSCPMAP SET INTBRDPARA SET DSCPMAP TRC IPADDR SET DSCPMAP STR IPCHK "6" SET DSCPMAP ADD/MOD IPPATH+SET PHBMAP In RNC sidethe recommended mode is to use ADD VLANID command to add IP VLAN mapping of the next hop one next hop one VLAN mapping. For signal plane and user plane IP address(es), the recommended mode is just to use ADD VLANID command to add IP VLAN mapping of the next hop. Don't add vlan by The value of DSCP cites the recommendation DSCP in table 1. The recommendation DSCP changes, it changes. The default DSCP value of BFD packet is 56. It can be changed by command "STR IPCHK". 6/23/2014 , 5680 235388102.xlsx.ms_office The DSCP Value or VLAN priority used in RAN should be planned in Transmission Device, and make sure the Transmission Device will not change the Values It's recommended to active the IPPM connections in NodeB side by command "ACT IPPOOLPM" on RNC. So the DSCP value of IPPM links are the same as in RNC side. DSCP CBS EBS 48 48 46 Physical Link BW*1000*1.5 0 34 Physical Link BW*1000*1.5 0 18 Physical Link BW*1000*1.5 0 10 Physical Link BW*1000*1.5 0 46High 18Low Huawei NodeB Configuration It's recommended to set flow control switch to "BW_SHAPING_ONOFF_TOGGLE" on NodeB in IPPOOL scenario. The Physical Link BW is the minimum bandwidth of physical link connection between RNC and NodeB. Don't set the destination ip address to 0.0.0.0 in command "ADD IPRT". Don't set the destination ip address to 0.0.0.0 in command "ADD IPRT". It's recommended to configure "End Point" mode in IPPOOL scenario. 6/23/2014 , 5780 235388102.xlsx.ms_office VLAN ID Command VLAN PriorityCommand DSCP(Command) ADD VLANMAP "6"(Vary according to the DSCP) SET DIFPRI(SIG) ADD VLANMAP "6"(Vary according to the DSCP) cite the DSCP value of SIG ADD VLANMAP "5"(Vary according to the DSCP) SET DIFPRI(OM) ADD VLANMAP "2"(Vary according to the DSCP) SET DIFPRI(OM) ADD VLANMAP "5"(Vary according to the DSCP) SET DIFPRI(OM) ADD VLANMAP "7"(default) determined by ARP Request determined by ARP Request ADD VLANMAP "5"(Vary according to the DSCP) SET DIFPRI(PTP) ADD VLANMAP "7"(Vary according to the DSCP) NULL ADD VLANMAP "7"(Vary according to the DSCP) ADD BFDSESSION ADD VLANMAP "7"(default) NULL ADD VLANMAP "7"(Vary according to the DSCP) PING ADD VLANMAP refilled according to the DSCP NULL ADD VLANMAP "7"(Vary according to the DSCP) TRACERT Learning "0"(default) NULL ADD CFMMA "6"(configured) The DSCP Value or VLAN priority used in RAN should be planned in Transmission Device, and make sure the Transmission Device will not change the Values The default map table between DSCP value and VLAN priority, can be modified by the command "SET DSCPMAP". The DSCP of CCH is the same with the DSCP of SIG. About the DSCP OMCH, the recommended configured mode is "OMHPRI=46, OMLPRI=18"("SET DIFPRI" command); means that the DSCP of some contol messages (eg:MML Command) is 46,and the DSCP of ordinary packets(such as log upload or software download) is 18. NoteFor 3G NodeBthe high DSCP of OM can not be equal to any other DSCP The recommended vlan configured mode is to use Single VLAN, not VLAN GROUP. and the VLAN priority will accord to map table with DSCP value. For example: ADD VLANMAP: NEXTHOPIP="x.x.x.x", MASK="255.255.255.255", VLANMODE=SINGLEVLAN, VLANID=YYY, SETPRIO=DISABLE; If the customer want to use "VLAN GROUP", please contact R&D to check it. "Single VLAN" mode is required in IPSec scenario. There are four types of traffic: User Data, SIG Data, Maintenance Data, and Other Data. Among which, the User Data is of different service levels according to the DSCP value. Each level will be mapped to the corresponding VLAN priority by using the default map table. The value of DSCP cites the recommendation DSCP in table 3. The recommendation DSCP changes it changes. 6/23/2014 , 5880 235388102.xlsx.ms_office Command Parameter Name IKE-Encryption algorithm IKE-Authentiation algorithm Authentiation method DH-Group IKE-PRF-Algotithm IKE-Version Exchange Mode Remote name DPD Mode DPD Idle Time(s) DPD Retransmission Interval(s) DPD Retransmission Coun Encapsulation mode Transform ESP-Encryption Algorithm ESP-Authentication Algorithm Ipsec Policy Parameters ADD IPSECPOLICY Perfect Forward Secrecy(PFS) Note 1: It's recommended to set the value of Source Wildcard to 0.0.0.0, when the ACL rules are configured in NodeB. Note 2: Authentication Encryption MD5 SHA1 DES 3DES AES128 AES192 AES256 IPSec Proposal Parameters ADD IPSECPROPOSAL In IPSec scenario, it's recommended that encryption algorithm and authentication algorithm combination in accordance with the green part of the table to complete PNP. IPSec Configuration IPSec Negotiation Parameters Table IKE Proposal Parameters ADD IKEPROPOSAL IKE Peer Parameters ADD IKEPEER 6/23/2014 , 5980 235388102.xlsx.ms_office Note 3: s In IPSec scenario, MBTS only use tunnel mode(encapsulation mode) and ESP(transform mode) to establish the IPSec tunnel. 6/23/2014 , 6080 235388102.xlsx.ms_office Recommended value Remark AES128/ AES192/ AES256 The Same with SeGW SHA1/ AES_XCBC_96 The Same with SeGW IKE_RSA_SIG The Same with SeGW DH_GROUP14/ DH_GROUP15 The Same with SeGW HMAC_SHA1/ AES128_XCBC The Same with SeGW IKE V2 The Same with SeGW Main Mode The same with seGW, when the IKEVERSION is IKE_V1, this parameter is needed. / If "IKE_RSA_SIG" is applied, the "Remote Name" must be the same as the name of peer end. If "PRE_SHARED_KEY" is applied, the "Remote Name" must be the same as the "subjectaltname" of peer end's certificate file. Periopic 10 5 5 tunnel The Same with SeGW ESP The Same with SeGW AES128/AES192/AES256 The Same with SecGW, this parameter is valid when the security protocol is ESP SHA1/SHA256/AES-XCBC- MAC-96 The Same with SecGW, this parameter is valid when the security protocol is ESP+AH DISABLE The Same with SeGW It's recommended to set the value of Source Wildcard to 0.0.0.0, when the ACL rules are configured in NodeB. SHA256 SHA-XCBC-MAC-96 In IPSec scenario, it's recommended that encryption algorithm and authentication algorithm combination in accordance with the green part of the table to complete PNP. IPSec Configuration IPSec Negotiation Parameters Table The Default value 6/23/2014 , 6180 235388102.xlsx.ms_office In IPSec scenario, MBTS only use tunnel mode(encapsulation mode) and ESP(transform mode) to establish the IPSec tunnel. 6/23/2014 , 6280 235388102.xlsx.ms_office Huawei RNC QoS configuration Table1 RNC Iub QoS configuration Huawei RNC PHB&DSCP Map Table Table2 PHB & DSCP Map Table The map rules from PHB to DSCP can be modified by the command"SET PHBMAP", It's recommanded to use the default map rules. Huawei RNC TRMMAP Configuration Table3 TRMMAP Configuration Rules Huawei NodeB QoS configuration Table4 DSCP Configuration Service Type DSCP(default) NCP&CCP (Common Channel&HSDPA Upload control frame) 48(default) OM(High Level) 34(default) OM(Low Level) 10(default) PTP(handshake packet) 34(default) USERDATA IPPATH 46(default) USERDATA IPPATH 38(default) USERDATA IPPATH 22(default) USERDATA IPPATH 14(default) BFD 34(default) 6/23/2014 6380 235388102.xlsx.ms_office The map rules from PHB to DSCP can be modified by the command"SET PHBMAP", It's recommanded to use the default map rules. DSCP(recommended) MML Command VLAN 48(recommended) SET DIFPRI 46(recommended) SET DIFPRI 18(recommended) SET DIFPRI 46(recommended) SET DIFPRI 46(recommended) ADD IPPATH 34(recommended) ADD IPPATH 18(recommended) ADD IPPATH 10(recommended) ADD IPPATH 56(recommended) ADD BFDSESSION It's recommanded to use SINGLEVLAN mode, and disable the SET PRIORITY,use the default VLAN priority map table. command:ADD VLANMAP 6/23/2014 6480 235388102.xlsx.ms_office SecurityFor Internal Auto adjust bandwidth switch Flow control switch ADD IPLOGICPORT OFF ON Note1: Note2: Note3: Note4: Note5: The Logical Port is not supported in the IP POOL scenario. It is recommended that setting the bandwidth of LOGICPORT according to the actual traffic or physics bandwidth limit. Huawei RNC Configuration If the IP traffic shaping and congestion control functions or the user plane resource separated by operators in RAN sharing is already enabled by running the ADD LP, ADD IPPATH command.set The bearing type of the virtual port to IPLOGICPORT , which indicates that the IPpath is used to carry the user plane resources of the specified operator. case 1 Logical Port(LP) Logical virtual port is introduced for traffic shaping, congestion detection and backpressure. Scenario 1: RNC and NodeB use FE or GE Port, and the bandwidth is not limited or the limited bandwidth is more than 8M, it's not recommended to configure Logical Port in RNC side. Scenario 3: RNC and NodeB use FE or GE Port, but the transmission bandwidth between RNC and nodeB is very low. RNC should configure one LP for each NodeBADD IPLOGICPORT. NodeB should configure LRSET LR. In Ethernet Load sharing Mode, it is forbidded that different NodeBs bear on one IPLOGICPORT. Scenario 2: RNC uses FE or GE Port, but NodeB uses the E1. RNC should configure one LP for each NodeBADD IPLOGICPORT. 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 65 of 80 235388102.xlsx.ms_office SecurityFor Internal It is recommended that setting the bandwidth of LOGICPORT according to the actual traffic or physics bandwidth limit. If the IP traffic shaping and congestion control functions or the user plane resource separated by operators in RAN sharing is already enabled by running the ADD LP, ADD IPPATH command.set The bearing type of the virtual port to IPLOGICPORT , which indicates that the IPpath is used to carry the user plane resources of the specified operator. Logical virtual port is introduced for traffic shaping, congestion detection and backpressure. Scenario 1: RNC and NodeB use FE or GE Port, and the bandwidth is not limited or the limited bandwidth is more than 8M, it's not recommended to configure Logical Port in RNC side. Scenario 3: RNC and NodeB use FE or GE Port, but the transmission bandwidth between RNC and nodeB is very low. RNC should configure one LP for each NodeBADD IPLOGICPORT. NodeB should configure LRSET LR. In Ethernet Load sharing Mode, it is forbidded that different NodeBs bear on one IPLOGICPORT. Scenario 2: RNC uses FE or GE Port, but NodeB uses the E1. RNC should configure one LP for each NodeBADD IPLOGICPORT. 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 66 of 80 235388102.xlsx.ms_office SecurityFor Internal THEN RNC NodeB Configuration RAN14 RAN14 RAN14 RAN15 RAN14 RAN14 RAN14 RAN15 RAN14 RAN15 RAN15 RAN15 FAQ 1)If the Iub interface is ATM transmission, please refer to document "Iub Tx configuration recommendation_ATM". 1) RNC and NodeB are both RAN15 version and there are newly established. If the RNC is upgraded from RAN14 to RAN15, keep the RAN14 configuration unchangeable. The matched version rules is following IF 1.How to use and refer to this configuration recommendation? 2. When shall we use RAN15 configuration Recommendation? 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 67 of 80 235388102.xlsx.ms_office SecurityFor Internal FAQ 1)If the Iub interface is ATM transmission, please refer to document "Iub Tx configuration recommendation_ATM". 1) RNC and NodeB are both RAN15 version and there are newly established. If the RNC is upgraded from RAN14 to RAN15, keep the RAN14 configuration unchangeable. The matched version rules is following 1.How to use and refer to this configuration recommendation? 2. When shall we use RAN15 configuration Recommendation? 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 68 of 80 235388102.xlsx.ms_office SecurityFor Internal No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 39 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 69 of 80 235388102.xlsx.ms_office SecurityFor Internal zhangyonggan creates the file on May 27th,2007. HSDPA_NRT PATH and HSUPA_NRT PATH need to configure separately in BSC6810. The 5-8E1s configuration is added. The default DSCP value of different service is changed in BSC6810 ADD "Logical Port" Sheet ADD the DSCP of Signal, User and OM. Modify the IPPATH Type from RT to HQ and LQ. Modify the Secondry PATH of MP+FE. ADD the explaination of PATH type of HQ and LQ. Separate two configuration table, one is RNC configuration table, the other is NodeB Add VLAN configuration recommendation and related rules. Modify the recommendation DSCP Value according to RNC V210B061 version Modify IPPATH type according to RAN 11 version. Add FE/GE port settiing and TRMMAP Note. Add the control plane bandwidth configuration rules in the ATM+FE scenaio Add TRMMAP table is added and IPPATH are reduced from 5 to 4(EF,AF43,AF23,AF13). The DSCP Control plane are modified from 46 to 48 in RNC side, in NodeB side SIG DSCP is 46. The DSCP of SIG is modified from 46 to 48 in NodeB side, in order to keep consistent with RNC. Enrich the DSCP and VLAN recommended configuration of OTHER type packets. Refresh the TRMMAP configuration. Recommend enable the IPPATH check in RNC side and disable the IPPATH check in NodeB side. Add the recommended VLAN priority for different traffic in NodeB side according to the DSCP value. Add the PTP(1588) VLAN configuration recommended when carried on UTRP board in NodeB side. Modify the R99 PS service and HSPA background service active factor to accord to conduction default configuration. Draw the scene of configure IPLOGICPORT /ATMLOGICPORT,make the understanding of mind easily. Mod the CBS value to Physical Link BW*1000*1.5 according to production default value. Add the configuration of IPPATH Ping type, the recommended type is UDP. Refresh the VLAN configuration of NodeB side, SINGLEVLAN mode is recommanded . Refresh the DSCP value of NodeB OMCH,distinguish high and low priority. Refresh the PHB and DSCP of IPPATH, modify AF43->AF41, AF23->AF21, AF13->AF11 in RNC side, modify the DSCP value of IPPATH in NodeB side from "46,38,22,14" to "46,34,18,10" Add 9/10/11/12*E1 recommended configuration in MPGRP Scenario. MOD OM High DSCP from 46 to 36 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 70 of 80 235388102.xlsx.ms_office SecurityFor Internal 1/24/2008 zhushimin 1/26/2008 zhushimin 3/3/2008 zhushimin 4/25/2008 liuli 4/25/2008 liuli 4/25/2008 liuli 4/25/2008 liuli 4/25/2008 liuli 8/22/2008 zhushimin 12/11/2008 zhushimin 1/20/2009 zhushimin 3/28/2009 zhushimin 8/17/2009 zhangyonggan 1/7/2010 huangmuhua 1/7/2010 huangmuhua 1/7/2010 huangmuhua 1/10/2011 huangmuhua 1/10/2011 huangmuhua 1/10/2011 huangmuhua 1/10/2011 huangmuhua 1/10/2011 huangmuhua 1/10/2011 huangmuhua 1/19/2011 Lu Feng 4/4/2011 huangmuhua 4/4/2011 huangmuhua 4/12/2011 huangmuhua 7/15/2011 huangmuhua 8/30/2011 gongwen 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 71 of 80 235388102.xlsx.ms_office SecurityFor Internal About this Tool The configuration principles mentioned below are based on that the total amount of bandwidth has already planned. Description for Items 1. 2 60 60 2 25 40.0% 1 60 60 2.5 30% The Maximum Number of Online User for Different E1s at the Same Time Num. of E1 1 2 3 4 5 1 2 3 4 5 The Maximum Number of Online User for Different E1s Num. of TS 12 15 22 24 2. 1984 kbps 1984 kbps Num. of Cells per NodeB The Maximum Number of Online User 3 Iub Dimensioning Tool Can be input and modified System Default Value Semi-manufactured Data This tool can be applied to UMTS5.1 version Iub Dimensioning. It just estimates approximately the IUB interface flux because of varying signaling procedure and size of signaling. Notes for input Result 6 6 315 400 Traffic Model Assumption 6 205 Constant/Default Values 3 65 Bandwidth of MP Link Bandwidth of PPP Link 35 60 3 42 3 Num. of Cells per NodeB The Maximum Number of Online User 3 80 3 160 Ratio of convergence of network Ratio of soft and Softer handover Margin for Engineering Calculation Frequency of DPB request procedure Average time interval of Softer handover for one user Average time interval of Soft handover for one user Average number of RLs for user in macro diversity Frequency of each subscribe for Attach, Detach, Location Updated, SMS etc. Average conversation time of CS subscriber Average conversation time of PS (DCCC as 1 access) Ratio of the subscribers of CS and PS 3 6 480 3 372 240 3 320 6 100 cell/s) : unit ate 13369344(r ) 1 SCR 1 ( 1) - MBS ( 10000000 CDVT PCR cell/s) : unit ate 13369344(r ) 1 SCR 1 ( 1) - MBS ( 10000000 6000000 PCR 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 72 of 80 235388102.xlsx.ms_office SecurityFor Internal 3. Traffic Analysis of NCP&CCP&ALCAP About the signaling of NBAP Flux of NCP Uplink: Flux of NCP Downlink: the signaling due to CS, PS and RRC only on DCH accessing procedure + the signaling due to soft handover Flux of CCP Uplink: Flux of CCP Downlink: Num. of E1 Number of R99Cell Number of H Cell Flux of NCP Uplink Flux of NCP Downlink 1 0 3 56631 11394 2 0 3 62328 22788 3 0 3 68025 34181 4 0 3 73722 45575 5 0 3 77425 52981 1 3 3 73577 14242 2 3 3 81054 29197 3 3 3 88888 44863 4 3 3 94940 56969 5 3 3 100637 68363 Num. of TS Number of R99Cell Number of H Cell Flux or NCP Uplink Flux of NCP Downlink 12 0 3 53426 4985 15 0 3 53925 5982 22 0 3 55207 8545 NCP&CCP&ALCAP Flux Evaluation The flux of CPs is estimated based on Iub signalling procedure 3GPP 25.433 8.2, the process of NBAP includes common and dedicated procedures. NCP bears the common procedure and CCPs bear the dedicated procedure. The common procedure is that one UE initiates the process of the NodeB communication which has nothing to do with special UE, such as:1)Common Transport Channel Setup, 2)Common Transport Channel Deletion, 3)Audit4)Common Measurement Initiation, 5)Common Measurement Reporting, 6)Common Measurement Termination, 7)Cell SetupCell Reconfiguration, 8)Cell Deletion, 9)Resource Status Indication, 10)System Information Update, 11)Radio Link Setup, 12)Physical Shared Channel Reconfiguration, 13)Reset. The dedicated procedure is the process that is related to the NodeB communication, such as.1)Radio Link Addition, 2)Synchronized Radio Link Reconfiguration Preparation, 3)Synchronized Radio Link Reconfiguration Commit, 4)Synchronized Radio Link Reconfiguration Cancellation, 5)Unsynchronized Radio Link Reconfiguration, 6)Radio Link Deletion, 7)Downlink Power Control, 8)Dedicated Measurement Initiation, 9)Dedicated Measurement Reporting, 10)Dedicated Measurement Termination, 11)Radio Link Failure, 12)Radio Link Restoration, 13)Compressed Mode Command. R99 cell common measurement report + H common measurement report + the signaling due to CS, PS and RRC accessing procedure + the signaling due to soft handover The main flux is due to common measurement report. the signaling due to CS, PS and RRC only on DCD accessing procedure + the signaling due to softer handover + the signaling of RL delete due to soft handover + the dedicated measurement report of TCP due to DPB The main flux is due to dedicated measurement report of TCP for DPB on every RL which is in macro diversity. the signaling due to CS, PS and RRC only on DCH accessing procedure + the signaling due to softer handover + the signaling of DPB request on the RLs in macro diversity. The main flux is due to the signaling of DPB request. Flux Calculations of NCP&CCP cell/s) : unit ate 13369344(r ) 1 SCR 1 ( 1) - MBS ( 10000000 CDVT PCR cell/s) : unit ate 13369344(r ) 1 SCR 1 ( 1) - MBS ( 10000000 6000000 PCR 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 73 of 80 235388102.xlsx.ms_office SecurityFor Internal 24 0 3 55563 9257 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 74 of 80 235388102.xlsx.ms_office SecurityFor Internal The configuration principles mentioned below are based on that the total amount of bandwidth has already planned. /h s s /s s s The Maximum Number of Online User Iub Dimensioning Tool Can be input and modified System Default Value Semi-manufactured Data This tool can be applied to UMTS5.1 version Iub Dimensioning. It just estimates approximately the IUB interface flux because of varying signaling procedure and size of signaling. Notes for input Result 315 400 Traffic Model Assumption 205 Constant/Default Values 65 35 60 42 The Maximum Number of Online User 80 160 480 372 240 320 100 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 75 of 80 235388102.xlsx.ms_office SecurityFor Internal the signaling due to CS, PS and RRC only on DCH accessing procedure + the signaling due to soft handover Flux of CCP Uplink Flux of CCP Downlink Total Flux Downlink 67734 42668 54062 135467 85335 108123 203201 128003 162185 270935 170671 216246 314962 198405 251386 84667 53335 67577 173568 109336 138533 266702 168004 212867 338669 213339 270308 406402 256006 324369 Flux of CCP Uplink Flux of CCP Downlink 29634 18667 23652 35560 22401 28382 50800 32001 40546 NCP&CCP&ALCAP Flux Evaluation The flux of CPs is estimated based on Iub signalling procedure 3GPP 25.433 8.2, the process of NBAP includes common and dedicated procedures. NCP bears the common procedure and CCPs bear the dedicated procedure. The common procedure is that one UE initiates the process of the NodeB communication which has nothing to do with special UE, such as:1)Common Transport Channel Setup, 2)Common Transport Channel Deletion, 3)Audit4)Common Measurement Initiation, 5)Common Measurement Reporting, 6)Common Measurement Termination, 7)Cell SetupCell Reconfiguration, 8)Cell Deletion, 9)Resource Status Indication, 10)System Information Update, 11)Radio Link Setup, 12)Physical Shared Channel Reconfiguration, 13)Reset. The dedicated procedure is the process that is related to the NodeB communication, such as.1)Radio Link Addition, 2)Synchronized Radio Link Reconfiguration Preparation, 3)Synchronized Radio Link Reconfiguration Commit, 4)Synchronized Radio Link Reconfiguration Cancellation, 5)Unsynchronized Radio Link Reconfiguration, 6)Radio Link Deletion, 7)Downlink Power Control, 8)Dedicated Measurement Initiation, 9)Dedicated Measurement Reporting, 10)Dedicated Measurement Termination, 11)Radio Link Failure, 12)Radio Link Restoration, 13)Compressed Mode Command. R99 cell common measurement report + H common measurement report + the signaling due to CS, PS and RRC accessing procedure + the signaling due to soft handover The main flux is due to common measurement report. the signaling due to CS, PS and RRC only on DCD accessing procedure + the signaling due to softer handover + the signaling of RL delete due to soft handover + the dedicated measurement report of TCP due to DPB The main flux is due to dedicated measurement report of TCP for DPB on every RL which is in macro diversity. the signaling due to CS, PS and RRC only on DCH accessing procedure + the signaling due to softer handover + the signaling of DPB request on the RLs in macro diversity. The main flux is due to the signaling of DPB request. Flux Calculations of NCP&CCP 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 76 of 80 235388102.xlsx.ms_office SecurityFor Internal 55034 34668 43925 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 77 of 80 235388102.xlsx.ms_office SecurityFor Internal Iub Dimensioning Tool Can be input and modified System Default Value Semi-manufactured Data Notes for input Result 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 78 of 80 235388102.xlsx.ms_office SecurityFor Internal Total Flux Uplink 124365 70303 197795 89672 271226 109041 344656 128410 392386 141000 158244 90667 254622 116089 355589 142722 433609 163301 507040 182671 83060 59408 89485 61103 106007 65461 Flux Calculations of NCP&CCP 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 79 of 80 235388102.xlsx.ms_office SecurityFor Internal 110596 66671 6/23/2014 Confidential Information of Huawei.No Spreading without Permission Page 80 of 80