Subject: DCCN Branch: IT Academic Year: 2014-15 Semester: I Faculty: K.ARCHANA
Question Number Previous Questions Date Conducted 1 For an electric device operating at 17 0 C with a bandwidth of 10 kHz, determine the thermal Noise power in watts and dBm.
2 For a ckt with a signal power of 10 W and a thermal noise power of 0.01W, determine the signal-to-noise power ratio.
3 Determine I. The peak frequency deviation Minimum bandwidth II. Buad for a binary FSK signal with a mark frequency of 49 kHz, a space frequency of 51 kHz , and input bit rate 2kbps
4
What are the key elements of a protocol? List out various standard organization that develop protocol standards.
Previous Questions (Unit II) Subject: DCCN Branch: IT Academic Year: 2014-15 Semester: I Faculty: K.ARCHANA
Question Number Date Previous Questions Date Conducted 1 Determine the characteristics of impedance for an air dielectric two-wire parallel transmission line with a D/r ratio of 12.22
2 Determine the characteristic of impedance for a coaxial cable with the following specifications: D=0.025 in, D=0.15 in, and r= 2.223
3 For a given length of coaxial cable with distributed capacitance C=96.6 pF/m and distributed inductance L=241.56 nH/m, and Dielectric constant r= 2.3 , determine the a. Velocity of propagation. b. Velocity factor
4 Distinguish between Synchronous and Statistical TDM
5 Briefly explain the characteristics of Guided media.
Previous Questions (Unit III) Subject: DCCN Branch: IT Academic Year: 2014-15 Semester: I Faculty: K.ARCHANA Question Number Previous Questions Date Conducted 1. 1. For a PCM system with the following parameters, determine a. Minimum sampling rate b. Minimum number of bits c. Resolution d. Quantization error
2. 2. For a single channel PCM system with a sample rate Fs=6000 samples per second and a 7-bit compressed PCM code, determine Line Speed.
3. 3. For a 20-channel PCM/TDM system with an 8 KHz sample rate, 10 bits per sample, and one framing bit per frame determine Line speed.
4.
Explain function and frame formats of MAC and physical layers of IEEE 802.11
5. Explain the concept of Selective Repeat ARQ protocol with a suitable example
Subject: DCCN Branch: IT Academic Year: 2014-15 Semester: I Faculty: K.ARCHANA Question Number Previous Questions Date Conducted 1 For an isotropic radiator emitting 10W of power, determine the power density 1000 meters from the source.
2 Determine the wave attenuation b/w two points with power density of p1=10W/m 2 and p2=0.1W/m 2
3 Determine the path loss for frequency of 6 GHz, travelling a distance of 50 km
4 Define FDMA,TDMA and CDMA, and what are the difference among FDMA,TDMA and CDMA ?
Subject: DCCN Branch: IT Academic Year: 2014-15 Semester: I Faculty: K.ARCHANA
Question Number Date
Previous Questions
Date conducted 1 Compute check characters for the code 39 message * C O D E space 3 9 *
2 Determine the single precision checksum for the following 5 character ASCII message. H E L L O 3 Determine the honey well check sum for the following four character ASCII message H E L P 4
Subject: DCCN Branch: IT Academic Year: 2014-15 Semester: I Faculty: K.ARCHANA
Question Number Previous Question Date conducted 1 Determine the character sequence for the following: a. General poll of station 8 b. Specific poll of device 10 at station 6
2 Determine the character sequence for BSC selection of device 22 at station 18
3 Determine the bit pattern for the control field of an information frame sent from the primary to secondary station for the following conditions: Primary is sending information frame 3(ns=3) Primary is polling the secondary(p=1) Primary is confirming correct reception of frames 2,3 and 4 from the secondary(nr=5)
4 Write a brief note on i. Web documents ii. Audio & Video Compare.
5 Write a brief note on
i. Network Management System. ii. Streaming Live Audio / Video.