Sie sind auf Seite 1von 2

misoperation.

Design practices with regard to the use of switches in trip


circuits vary among utilities. The advantage of such switches is that they
can make testing more safe and efficient. The disadvantage is that if such
switches are left in the improper position, protection may not be available
when needed.
Diodes are used in trip circuits to provide the ability for DC current to
flow in one direction through a portion of the circuit. Diodes can facilitate
providing logic into the circuits that would otherwise require the use of
auxiliary relays. The use of diodes reduces cost and complexity of the
circuitry. The disadvantage of using diodes is that they are subject to failure,
which can remain undetected until a misoperation occurs.
14.20.4 TRIP COILS
The function of trip coils is to initiate action to open the main contacts of
breakers. The actual energy to open the contacts is provided by some form of
stored energy such as springs, compressed air, and high-pressure gas. Trip
coils therefore do not directly open the contacts, but act to release a latch or
open a valve that allows the release of some form of stored energy used to
move the contacts. Breaker designs can vary considerably among manufac-
turers and it is important for protection engineers to understand the charac-
teristics of the trip coils and other control devices used in the specific breaker
that is used, so that proper trip circuit designs can be developed.
14.21 TRIP CIRCUIT DESIGN
Trip circuits may be required to trip a single breaker or multiple breakers.
Tripping of a single breaker is usually associated with distribution feeders,
subtransmission lines, and industrial circuits. Multiple breakers need to be
tripped with bus arrangements such as breaker-and-a-half, ring bus, or double
busdouble breaker designs. Such designs are usually associated with higher-
voltage systems.
Various arrangements are possible for trip circuit designs, which are
highly influenced by individual company practices and experience. A special
publication by the IEEE Power System Relaying Committee Relay
Trip Circuit Design should be used as reference for more detail on this
subject.
Regardless of the design details, some general requirements that need to
be addressed when developing designs for trip circuits are as follows:
1. Adequate voltage must be delivered to the trip coil(s) to assure reliable
breaker operation. All possible voltage drops that may exist in the
circuit must be considered when determining voltage available at
the trip coil(s).
2006 by Taylor & Francis Group, LLC.
2. Sufficient DC current must be avai lable to operate tar gets on all relays
that have operate d. Proper tap settings and coil rating s need to be
selected for target and seal-in units.
3. Care must be taken to avoi d connec tions between DC circuits . Such
connections can result in the loss of both prima ry and backup relays for
a sing le failure on the DC system .
4. Currents drawn by auxi liary relays must not cause inco rrect operation
of seal-in units or the failur e of such units to drop out prope rly .
5. Protection against surge s caused by the operation of the vario us coils
that exist in the cont rol circuitry should be appl ied to protect other
equipment connec ted in the circui t. This is especia lly import ant to
protect d elicate elect ronic equi pment that is used in many o f the
more mode rn subst ations.
6. Relay coils shoul d be connecte d to the negat ive DC bus.
This is required to minimi ze the potential failure of such coils be-
cause of a build-u p of corrosion . Coil s that are direct ly connecte d to
the positive DC bus are subject to corrosi on wi th the pres ence of
moisture .
14.22 TRIP CIRCUIT MONITORING AND ALARMS
Su pervision of cont rol cir cuitry that affects the ability of trippin g functio ns to
perf orm prope rly is an import ant enhanc ement for protectio n relia bility.
Im portant conditions for which monit oring should be consider ed include the
fol lowing:
1. Inadequate DC tripping volt age includes low DC voltage leve ls
(battery problems) , open brea ker trip coil, blown fuse in a DC circui t,
or an opening in the DC circuit wiring.
2. Loss of AC pote ntial to prima ry and backup relaying.
3. Loss of communication channels that are used to initiate tripping.
4. Relay problems when self-checking features are available.
A common means for monitoring availability of DC tripping voltage is by
connecting lamps in the DC tripping circuit. A simple arrangement for
connec ting such lamps in a trip circui t is illus trated in Figur e 14.10.
When the breaker is closed, the red lamp provides indication of the availabil-
ity of DC voltage to the trip coil. When the breaker is open, the green lamp
provides similar indication. The red and green lamps also provide indication
for the breaker positionthe red lamp will be lit when the breaker is closed
and the green lamp will be lit when the breaker is open. The lamps are usually
mounted on the control panel within the substation at a location where the
associated breaker is clearly identified. The lamps that are used must meet
requirements of the DC circuit into which they are installed and should
2006 by Taylor & Francis Group, LLC.

Das könnte Ihnen auch gefallen