0 Bewertungen0% fanden dieses Dokument nützlich (0 Abstimmungen)
104 Ansichten191 Seiten
PLANT DESIGN AND PIPING ENGINEERING DESIGN GUIDE FOR CONVEYOR DESIGN (ORIGINAL) DESIGN STANDARD NO. 3DG-P04A-202-00 BECHTEL CORPORATION MINING and METALS SAN FRANCISCO 0 Jan 94 Issued for Implementation M&M Design Specialists REV. DATE REASON for REVISION BY CHECKED APPROVAL DETAILS and DESIGNS WERE DEVELOP
PLANT DESIGN AND PIPING ENGINEERING DESIGN GUIDE FOR CONVEYOR DESIGN (ORIGINAL) DESIGN STANDARD NO. 3DG-P04A-202-00 BECHTEL CORPORATION MINING and METALS SAN FRANCISCO 0 Jan 94 Issued for Implementation M&M Design Specialists REV. DATE REASON for REVISION BY CHECKED APPROVAL DETAILS and DESIGNS WERE DEVELOP
PLANT DESIGN AND PIPING ENGINEERING DESIGN GUIDE FOR CONVEYOR DESIGN (ORIGINAL) DESIGN STANDARD NO. 3DG-P04A-202-00 BECHTEL CORPORATION MINING and METALS SAN FRANCISCO 0 Jan 94 Issued for Implementation M&M Design Specialists REV. DATE REASON for REVISION BY CHECKED APPROVAL DETAILS and DESIGNS WERE DEVELOP
0 Jan 94 Issued for Implementation M&M Design Specialists REV. DATE REASON FOR REVISION BY CHECKED APPROVAL PLANT DESIGN AND PIPING ENGINEERING DESIGN GUIDE No. 3DG-P04A-202-00
TABLE OF CONTENTS
TABLE OF NOTATIONS
SECTION 1 ELEMENTS OF A CONVEYOR, TRIGONOMETRY OF CURVES
SECTION 2 HEAD AND TAIL PULLEY FRAMES, STRINGERS
SECTION 3 TRANSFER AND LOADING POINTS
SECTION 4 SKIRTING
SECTION 5 TAKE-UPS
SECTION 6 BELT CLEANERS
SECTION 7 HOODS, SCREENS, GUARDS AND COVERS
SECTION 8 SPARE
SECTION 9 MISCELLANEOUS
SECTION 10 ADDENDA
NOTE: BULLET SHOWN PRECEDING THE DRAWING NUMBER ON EACH SECTION INDEX DENOTES A CAD FILE DRAWING.
DETAILS AND DESIGNS WERE DEVELOPED TO COMPLY WITH US STANDARDS AND CODES.
ALL PROJECTS UTILIZING THIS DESIGN GUIDE SHOULD ENSURE COMPLIANCE TO PREVAILING COUNTRY, LOCAL CODE AND SAFETY STANDARDS AND AVAILABLE HARDWARE AND COMPONENT DIMENSIONS.
TABLE OF NOTATIONS
PW Pulley width (face width), inches
y Trigonometry of curves, (feet and inches) P
z Height of top of head pulley over belt line, (inches) Q
Angle of inclination of belt
q
Trigonometry of conveyor curves, (degrees)
R Radius, (feet and inches)
Trigonometry of conveyor curves, (degrees) R 1 R + h d or R - h d (feet and inches)
Trigonometry of conveyor curves, (degrees) S Length of belt line curve, (feet and inches)
Trigonometry of conveyor curves, (degrees) S i Idler spacing, (feet and inches)
Arc of contact; surcharge angle of conveyed material, (degrees) S ic Idler spacing on a curve (feet and inches)
Angle of repose of conveyed material (degrees) S s Stringer length, (feet and inches)
T Trigonometry of curves, (feet and inches)
T 1 Trigonometry of curves, (feet and inches)
TU Take-up travel (feet and inches)
U Trigonometry of curves, (feet and inches)
V Trigonometry of curves, (feet and inches)
WP Working point
w
w 1 First width of skirting, (inches)
w 2 Last width of skirting (inches)
TABLE OF NOTATIONS
Refer to number sheet in this guide
h d Height of belt line over idler base, (inches) A Area (ft 2 ) hi Shim height of idler (inches)
A Return roller length, (inches) h 1 First height of skirting over belt line, (inches) A t Belt loading, ft 2 h 2 Last height of skirting over belt line, (inches) a 1 Height of center of gravity of load. Cross-section of conv. belt at pulley (inches) h 3 Height of belt line to bottom of stile B Bearing centers, (inches)
h S Depth of material touching skirtboards, (inches) b Belt width, (inches)
J Transition distance, (feet and inches) C Chute width, (inches)
j c 2 Edge distance, edge of material to edge of belt (inches) K Distance above or below belt line to radius point D
k d m Material bulk density (pounds per cubic feet)
L Pulley centers, (feet and inches) E Troughing idler roller length, inches (equal length rolls)
L h Horizontal pulley centers, (feet and inches) E Trigonometry of curves, (feet and inches)
l Length of skirting, (feet and inches) E 1 Trigonometry of curves, (feet and inches)
M Height of attachment plate e t Load Point of Tangency
m F Top of troughing idler roller edge height above base, (inches)
N Spacing of skirting supports (feet and inches) f Lc stringer to L c idler
n Number G Troughing idler width between roller PD Pulley Diameter (including lagging), inches.
at top (inches)
H Lift, vertical distance between tail pulley work point and head pulley work point (feet and inches)
PI Point of Intersection h Height, above the belt surface on the top of the load, tangent to pulley (inches) PT Point of Tangency
SECTION 1 ELEMENTS OF A CONVEYOR, TRIGONOMETRY OF CURVES
1.01 Elements of a Belt Conveyor 1.02 Elements of a Belt Conveyor 1.03 Typical Conveyor Profile 1.04 Location of Pulleys W.P. and Transition Distance 1.05 Basic Dimensional Data for Curves 1.06 Trigonometry of a Convex Curve - One Tangent Horizontal 1.07 Trigonometry of a Convex Curve - Neither Tangent Horizontal 1.08 Trigonometry of a Concave Curve - One Tangent Horizontal 1.09 Trigonometry of a Concave Curve - Neither Tangent Horizontal 1.20 Angles of Surcharge 1.21 Angles of Repose and Conveyor Inclination 1.22 Metric Standard-Conveyor Belt Widths 1.23 Conversion Table-Degree/Bevel/Percent
0 Issued as Design Guide DFH ABC REV. DATE REASON FOR REVISION BY CHECKED APPR OVAL DRAWING NO. 1.01
Elements of a Belt Conveyor Sheet 1 of 1 M&M
0 Issued as Design Guide DFH ABC REV. DATE REASON FOR REVISION BY CHECKED APPR OVAL DRAWING NO. 1.02
Elements of a Belt Conveyor Sheet 1 of 1 M&M
0 Issued as Design Guide FJC ABC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 1.03
Typical Conveyor Profile Sheet 1 of 1 M&M
0 Issued as Design Guide AM VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 1.04
Location of Pulleys W.P. and Transition Distance Sheet 1 of 1 M&M
0 Issued as Design Guide RT JS REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 1.05
Basic Dimensional Data for Curves Sheet 1 of 1
M&M
0 Issued as Design Guide RT JS REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 1.06
Trigonometry of a Convex Curve One Tangent Horizontal Sheet 1 of 1
M&M
0 Issued as Design Guide RT JS REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 1.07
Trigonometry of a Convex Curve Neither Tangent Horizontal Sheet 1 of 1
M&M
0 Issued as Design Guide RT JS REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 1.08
Trigonometry of a Convex Curve One Tangent Horizontal Sheet 1 of 1
M&M
0 Issued as Design Guide RT JS REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 1.09
Trigonometry of a Convex Curve Neither Tangent Horizontal Sheet 1 of 1
M&M
0 Issued as Design Guide FJC VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 1.20
Angles of Surcharge Sheet 1 of 1 M&M
Material
Average Weight (lbs./ft. 3 )
Fill Angle of Repose (Degrees) Maximum Conveyor Inclination (Degrees)
Notes: 1. For preliminary design of conveyors utilizing metric belt widths, use nearest inch equivalent and refer to U.S. MFR for approximately idler dimensions.
* Denotes preferred size.
0 Issued as Standard GD DW REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 1.22
Metric Standard Conveyor Belt Widths Sheet 1 of 1 M&M
Inclination (degrees) Rise, inches per foot Percent Rise
1 / 4
1 / 14 0.43
1 / 2
1 / 8
0.87
3 / 4
5 / 22
1.30
1 7 / 52 1.74
2 15 / 32
3.49
3 5 / 8
5.24
4 27 / 32 6.99
5 1 1 / 14 8.74
6 1 29 / 32 10.51
7 1 15 / 22 12.27
8 1 11 / 14 14.05
9 1 29 / 32 15.83
10 2 1 / 8 17.63
11 2 11 / 32 19.44
12 2 1 / 2 21.25
13 2 25 / 32 23.08
14 3 24.94
15 3 7 / 32 26.79
16 3 7 / 16 28.67
17 3 21 / 32 30.57
18 3 29 / 33 32.49
19 4 1 / 8 34.43
20 4 7 / 8 36.39
21 4 19 / 32 38.28
0 Issued as Design Guide GD DW REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 1.23
Conversion from Degrees to Rise Inches per Foot and Percent Rise Sheet 1 of 1
M&M
SECTION 2 HEAD AND TAIL PULLEY FRAMES, STRINGERS
2.01 Head Pulley Frame, Bearing Horizontally Mounted 2.02 Tail Pulley Frame, Bearing Horizontally and Incline Mounted 2.03 Tail Pulley Frame, Bearing Incline Mounted 2.04 Heavy Duty Head and Tail Pulley Frames, Selection of Members S1 and S2 2.05 Head and Tail Pulley Frames, Dimensional Data 2.06 Head Pulley Frame, Standard Heavy Duty, Fabricated 2.07 Tail Pulley Frame, Bearing Vertically Mounted 2.08 Tail Pulley Frame, Bearing Vertically Mounted 2.09 Vee-Troughing Return Idler - Wet Area 2.10 Conveyor Truss, Typical Cross-Section 2.11 Typical Cross Sections (Trough Conveyor Run) 2.12 Typical Stringer Assembly 2.121 Design Protection Against Corrosion 2.13 Stringer (S3) - Support (S4) Selection, Sheet 1 of 3 2.14 Stringer (S3) - Support (S4) Selection, Sheet 2 of 3 2.15 Stringer (S3) - Support (S4) Selection, Sheet 3 of 3 2.16 Arrangement of Stringers in Concave and Convex Curves 2.17 Support of Idlers Through a Curve 2.18 Determination of Stringer Lengths in a Concave Curve 2.19 Determination of Stringer Length in a Curve 2.20 Close Approximation of Idler Shim Height in Curves 2.21 Stringer Arrangements in Short Radius Convex Curves 2.22 Idler Spacing 2.25 Typical Conveyor Stringer Modulized Suspension. Horizontal Conveyor 36 Wide or Larger 2.26 Typical Conveyor Stringer Modulized Suspension. Inclined Conveyor 36" Wide or Larger 2.27 Typical Cross-Section for Conveyor Tunnel Belt 36 Wide or Larger 2.28 Typical Cross-Section for Conveyor Tunnel (Tube) Belt 36 Wide or Larger
2.29 Overland Conveyor-Modular Section with Rigid Idlers 2.30 Overland Conveyor-Modular Section with Heavy Duty Rigid Idlers (1 of 2) 2.301 Overland Conveyor-Modular Section with Heavy Duty Rigid Idlers (2 of 2) 2.3l Overland Conveyor - Modular Section with Heavy Duty Rigid Idlers 2.50 Pulley Bearing Positioning. Dodge Pillow Blocks 2.51 Pulley Bearing Positioning. Link Belt and SKF Pillow Blocks
0 Revised, Redrawn and Reissued for Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.01
Head Pulley Frame Bearings Horizontally Mounted Sheet 1 of 1 M&M
0 Revised, Redrawn and Reissued for Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.02
Tail Pulley Frame Bearings Horizontally and Incline Mounted Sheet 1 of 1 M&M
0 Revised, Redrawn and Reissued for Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.03
0 Issued as Design Guide RT VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.04
Heavy Duty Head and Tail Pulley Frames Selection of Members S1 and S2 Sheet 1 of 1
M&M
0 Issued as Design Guide AM VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.05
Head and Tail Pulley Frames Dimensionsal Data Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued for Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.06
Head and Tail Pulley Frames Standard, Heavy Duty Fabricated Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.07
Tail Pulley Frame Bearings Vertically Mounted Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued for Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.08
Tail Pulley Frame Bearings Vertically Mounted Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.09
Vee-Troughing Return Idler Wet Area Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued for Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.10
Conveyor Truss Typical Cross-Section Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued for Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.11
Typical Cross-Section Trough Conveyor Run Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued for Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.12
Typical Stringer Assembly Sheet 1 of 1
M&M
In dealing with copper sulfide ore or any other corrosive ore, special attention in steel design against corrosion problems should be considered.
1. In mild steel design eliminate or minimize possibilities of collection dust ore lumps and moisture by providing self cleaning surfaces and weep holes for relieving trapped water.
Areas of metal subjected to severe corrosion to be sand blasted to near white metal and painted with inorganic zinc.
2. Creating unavoidable collection pockets or surface, design should call for using low grade stainless steel or using extra thickness for corrosion allowance.
0 Issued as Design Guide REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.121
Design Protection Against Corrosion Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard RT JS REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.13
Stringer (S3) - Support (S4) Selection Sheet 1 of 3
M&M
0 Issued as Design Guide RT JS REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.14
Stringer (S3) - Support (S4) Selection Sheet 2 of 3
M&M
0 Issued as Design Guide RT JS REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.15
Stringer (S3) - Support (S4) Selection Sheet 3 of 3
M&M
0 Issued as Design Guide V.T.A V.T.A REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.16
Arrangement of Stringers in Concave and Convex Curves Sheet 1 of 1
M&M
0 Issued as Design Guide V.T.A V.T.A REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.17
Support of Idlers Through a Curve Sheet 1 of 1
M&M
0 Issued as Design Guide RT JS REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.18
Determination of Stringer Lengths in a Concave Curve Sheet 1 of 1
M&M
0 Issued as Design Guide AM JS REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.19
Determination Of Stringer Length in a Curve Sheet 1 of 1
M&M
0 Issued as Design Guide AM C.C.C. REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.20
Close Approximation of Idler Shim Height in Curves Sheet 1 of 1
M&M
0 Issued as Design Guide RT V.T.A REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.21
Stringer Arrangements in Short Radius Convex Curves Sheet 1 of 1
M&M
S i Normal Spacing of Troughing Idlers, Feet
Idler spacing (S i ) on long center belt conveyors can vary when constant belt sag between idlers is desired. This variation is dependent upon belt tension and weights of belts plus carried material. Refer to CEMA Handbook pages 54 and 55.
In a convex curve the belt exerts a greater force on carrying idlers. Consequently, the idler spacing in convex curves (S ic ) is frequently less than normal idler spacing. Refer to CEMA Handbook pages 294, 295 and 296.
0 Issued as Design Guide G.C REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.22
Idler Spacing Sheet 1 of 1 M&M
0 Revised, Redrawn and Reissued as Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL Typical Conveyor Stringer DRAWING NO. 2.25
Modulized Suspension Horizontal Conveyor 36 Wide or Larger Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL Typical Conveyor Stringer DRAWING NO. 2.26
Modulized Suspension Inclined Conveyor 36 Wide or Larger Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.27
Typical Cross-Section for Conveyor Tunnel Belt 36 Wide or Larger Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.28
Typical Cross Section for Conveyor Tunnel (Tube) Belt 36 Wide or Larger Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.29
Overland Conveyor Modular Section with Rigid Idlers Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.30
Overland Conveyor - Modular Section with Heavy Duty Rigid Idlers Sheet 1 of 2
M&M
0 Revised, Redrawn and Issued as Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.301
Overland Conveyor - Modular Section with Heavy Duty Rigid Idlers Sheet 2 of 2
M&M
0 Revised, Redrawn and Reissued as Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.31
Overland Conveyor - Modular Section with Heavy Duty Rigid Idlers Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.50
Pulley Bearing Positioning Dodge Pillow Blocks Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued for Standard
REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 2.51
Pulley Bearing Positioning Link-Belt and SKF Pillow Blocks Sheet 1 of 1
M&M
SECTION 3 TRANSFER AND LOADING POINTS
3.01 Typical Transfer with Rock Box and Boot Jack 3.011 Throat Clearance Above Boot Jack Shelf 3.01-A Typical Transfer with Rock Box Boot Jack and Impact Table 3.02 Typical Transfer with Reversing Rock Box and Boot Jack 3.02-A Typical Transfer with Reversing Rock Box and Boot Jack and Impact Table 3.03 Typical Transfer with Grizzly 3.04 Typical Right Angle Transfer with Rock Box and Boot Jack 3.04-A Typical Right Angle Transfer with Rock Box, Boot Jack and Impact Table 3.05 Height Through Any Oblique or Right Angle Transfer 3.06 Typical Right Angle Transfer with Rock Box and Boot Jack Dribbles Not Collected in Chute 3.06-A Typical Right Angle Transfer with Rock Box, Boot Jack and Impact Table, Dribbles Not Collected in Chute 3.07 Typical Right Angle Transfer with Rock Box and Boot Jack Dribbles Collected in Chute 3.07-A Typical Right Angle Transfer with Rock Box and Boot Jack Dribbles Collected in Chute 3.08 Typical In-Line Transfer - Wet Material 3.08-A Typical In-Line Transfer with Impact Table For Wet Material 3.09 Typical Right Angle Transfer - Wet Material 3.09-A Typical Right-Angle Transfer with Impact Table for Wet Material 3.10 Conveyor Loading Zone - Rigid Idler Support 3.10-A Conveyor Loading Zone Rigid Impact Table 3,11 Typical Transfer Station with Garland Impact Idlers 3.12 Typical Right Angle Transfer - Green Ball Pellets 3.30 Typical Boot Jack Suspended Within Chute 3.31 Typical Boot Jack Supported on Skirting Attachment Plates 3.32 Coarse Ore Conveyor Loading with Grizzly Fingers 3.40 4" x 4" Cast Wear Bar 3.41 4" x 2" Cast Wear Bar 3.42 Liner Plate
3.60 Plotting the Trajectory of Material Discharging from Head Pulley, Sheet 1 3.61 Plotting the Trajectory of Material Discharging from Head Pulley, Sheet 2 3.62 Plotting the Trajectory of Material Discharging from Head Pulley, Sheet 3 3.63 Plotting the Trajectory of Material Discharging from Head Pulley, Sheet 4 3.64 Plotting the Trajectory of Material Discharging from Head Pulley, Sheet 5 3.65 Plotting the Trajectory of Material Discharging from Head Pulley, Sheet 6
0 Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.01
Typical Transfer with Rock Box and Boot Jack Sheet 1 of 1 M&M
0 Issued as Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.01-A
Typical Transfer with Rock Box Boot Jack and Impact Table Sheet 1 of 1
M&M
In development of conveyor transfer arrangement using boot-jack design the following conditions should be recognized and design considerations taken into account.
I. Be aware of reduced throat area caused by ore build-up on boot-jack shelf. II. Check area of throat opening. The area should be equal or exceed cross-sectional area of ore carried on belt multiplied by a spread factor 4. Use formula: Minimum area of throat opening (ft 2 ) = ( ) ( ) TPH x 2240 60 ore density lb./ft x conv. speed fpm x4 3
III. Consider maximum dimension of ore handled and provide throat opening of no dimension smaller than 3 times maximum lump size for ore under 12 in., or 2 times maximum lump size for ore 12 in. and larger. IV. Compare results of II and III above and select design bases giving largest size opening.
Reference to: Drawing. No. 3.01 3.02 3.03
0 Issued as Design Guide REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.011
Throat Clearance Above Boot-Jack Shelf Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.02
Typical Transfer with Reversing Rock Box and Boot Jack Sheet 1 of 1 M&M
0 Issued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL Typical Transfer DRAWING NO. 3.02-A
with Reversing Rock Box, Boot Jack and Impact Table Sheet 1 of 1 M&M
Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.03
Typical Transfer With Grizzly Sheet 1 of 1 M&M
0 Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.04
Typical Right Angle Transfer with Rock Box and Boot Jack Sheet 1 of 1
Issued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL Typical Right Angle Transfer DRAWING NO. 3.04-A M&M
with Rock Box Boot Jack and Impact Table Sheet 1 of 1
HEIGHT THROUGH ANY OBLIQUE OR RIGHT ANGLE TRANSFER
For most materials, a certain amount of fines will get by the scraper. Some part of this material will come off the belt at the snub pulley. For clean materials, this can be a small quantity and not worth any substantial additional costs. But, for a great many materials, particularly when it is abrasive and scrapers can be expected to wear quickly and perform marginally, the amount of material shaken off at the snub can be considerable.
The designer should lay out the transfer so the dribble from the snub pulley can either be chuted through the transfer or disposed of by other means.
For the first case, some additional height will be required thru the transfer. Additional height always means more wear, more dust and more cost, but unless degradation is a problem, this solution is definitely preferable.
Alternately, clear floor space under the transfer, a sump, or hopper, or even a short dribble belt may be required. Accumulated fines could be disposed of by shoveling onto the second belt or, if large quantities are involved, removed by front end loaders or similar clean up vehicles.
0 Issued as Design Guide FJC ABC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.05 M&M
Height Through Any Oblique or Right Angle Transfer Sheet 1 of 1
0 Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL M&M
Typical Right Angle Transfer DRAWING NO. 3.06
With Rock Box and Boot Jack Dribbles Not Collected in Chute Sheet 1 of 1
0 Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL M&M
Typical Right Angle Transfer DRAWING NO. 3.06-A
With Rock Box, Boot Jack and Impact Table Dribbles Not Collected in Chute Sheet 1 of 1
Revised, Redrawn and Reissued for Standard GPN M&M
REV. DATE REASON FOR REVISION BY CHECKED APPROVAL Typical Right Angle Transfer DRAWING NO. 3.07
With Rock Box and Boot Jack Dribbles Collected in Chute Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL Typical Right Angle Transfer DRAWING NO. 3.07-A
with Rock Box and Boot Jack Dribbles Collected in Chute Sheet 1 of 1
M&M
Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.08
Typical In-Line Transfer Wet Material Sheet 1 of 1
M&M
0 Issued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL Typical In-Line Transfer DRAWING NO. 3.08-A
with Impact Table for Wet Material Sheet 1 of 1
M&M
Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.09
Typical Right-Angle Transfer Wet Material Sheet 1 of 1
M&M
0 Issued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL Typical Right-Angle Transfer DRAWING NO. 3.09-A
with Impact Table for Wet Material Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.10
Conveyor Loading Zone Rigid Idler Support Sheet 1 of 1
M&M
0 Issued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.10-A
Conveyor Loading Zone Rigid Impact Table Sheet 1 of 1
M&M
Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.11
Typical Transfer Station with Garland Impact Idlers Sheet 1 of 1 M&M
0 Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.12
Typical Right Angle Transfer Green Ball Pellets Sheet 1 of 1
M&M
Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.30
Typical Boot Jack Suspended Within Chute Sheet 1 of 1
M&M
Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.31
Typical Boot Jack Supported on Skirting Attachment Plates Sheet 1 of 1 M&M
0 Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.32
Coarse Ore Conveyor Loading with Grizzly Fingers Sheet 1 of 1 M&M
0 Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.40
4 x 4 Cast Wear Bar (Heavy Duty) Sheet 1 of 1 M&M
0 Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.41
4 x 2 Cast Wear Bar Sheet 1 of 1
Revised, Redrawn and Reissued for Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL M&M
DRAWING NO. 3.42
Liner Plate Sheet 1 of 1
0 Issued as Design Guide FJC ABC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.60 M&M
Plotting the Trajectory of Material Discharging from the Head Pulley Sheet 1 of 6
0 Issued as Design Guide FJC ABC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.61 M&M
Plotting the Trajectory of Material Discharging from the Head Pulley Sheet 2 of 6
0 Issued as Design Guide JAL JS REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.62 M&M
Plotting the Trajectory of Material Discharging from the Head Pulley Sheet 3 of 6
0 Issued as Design Guide JAL JS REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.63 M&M
Plotting the Trajectory of Material Discharging from the Head Pulley Sheet 4 of 6
0 Issued as Design Guide JAL JS REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.64 M&M
Plotting the Trajectory of Material Discharging from the Head Pulley Sheet 5 of 6
0 Issued as Design Guide FJC VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 3.65 M&M
Plotting the Trajectory of Material Discharging from the Head Pulley Sheet 6 of 6 M&M
SECTION 4 SKIRTING
4.01 Skirting, General 4.02 Skirting, Type 1 Data 4.03 Skirting, Type 1 Data 4.04 Skirting, Type 1 Data 4.05 Skirting, Type 2 Data 4.06 Skirting, Dimensional Data 4.10 Skirting, and Cover Support Frame, Type 1-A 4.11 Skirting, and Cover Support Frame, Type 1-B 4.12 Skirting, and Cover Support Frame, Type 2 4.13 Skirting, Support Frame and Clamp Spacing 4.14 Skirting, Dimensional Data 4.20 Skirting, Attachment by Bolting 4.21 Skirting, Attachment by Bolting, Alternate 4.22 Skirting, Attachment by Wedging 4.23 Skirting, Attachment by Toggle Clamp 4.24 Skirting, Attachment by Toggle Clamp, Alternate 4.25 Skirting, Attachment by Toggle Clamp, Alternate 4.26 Skirting, Attachment by Wing Nut 4.27 Sealed Skirting 4.28 Skirting, Attachment by Stud 4.29 Skirting, Hinged Tail End Closure 4.30 Skirting, Curtain at Discharge End of Skirting 4.31 Skirting, Hinged Tail End Closure 4.32 Skirting, Curtain at Discharge End of Skirting 4.33 Skirting, Spill Loading Door 4.34 Adjustable Bang Board Deflector 4.35 Skirting, Lump Spill Barrier 4.36 Skirting for 5 Roll Troughing Garland Idlers 4.37 Skirting and Support for 5 Roll Impact Garland Idlers
4.90 Rubber for Skirting and Scrapers
0 Issued as Design Guide VTA VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.01
Skirting General Sheet 1 of 1
M&M
0 Issued as Design Guide VTA VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.02
Skirting Type 1 Data Sheet 1 of 1
M&M
0 Issued as Design Guide VTA VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.03
Skirting Type 1 Data Sheet 1 of 1
M&M
0 Issued as Design Guide VTA VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.04
Skirting Type 1 Data Sheet 1 of 1
M&M
0 Issued as Design Guide VTA VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.05
Skirting Type 2 Data Sheet 1 of 1
M&M
0 Issued as Design Guide DH CCC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.06
Skirting Dimensional Data Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.10
Skirting and Cover Support Frame Type 1-A Sheet 1 of 1 M&M
0 Revised, Redrawn and Reissued as Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.11
Skirting and Cover Support Frame Type 1-B Sheet 1 of 1
0 Revised, Redrawn and Reissued as Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.12 M&M
Skirting and Cover Support Frame Type 2 Sheet 1 of 1
0 Revised, Redrawn and Reissued as Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.13
Skirting Support Frame and Clamp Spacing Sheet 1 of 1 M&M M&M
0 Issued as Design Guide RT VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.14
Skirting Dimensional Data Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.20
Skirting Attachment by Bolting Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL Skirting DRAWING NO. 4.21
Attachment by Bolting Alternate Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.22
Skirting Attachment by Wedging Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.23
Skirting Attachment by Toggle Clamp Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL Skirting DRAWING NO. 4.24
Attachment by Toggle Clamp Alternate Sheet 1 of 1 M&M
0 Revised, Redrawn and Reissued as Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL Skirting DRAWING NO. 4.25
Attachment by Toggle Clamp Alternate Sheet 1 of 1 M&M
0 Revised, Redrawn and Reissued as Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.26
Skirting Attachment by Wing Nut Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.27
Sealed Skirting Sheet 1 of 1 M&M
0 Revised, Redrawn and Reissued as Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.28
Skirting Attachment by Stud Sheet 1 of 1
0 Revised, Redrawn and Reissued as Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL M&M
DRAWING NO. 4.29
Skirting Hinged Tail End Enclosure Sheet 1 of 1
0 Revised, Redrawn and Reissued as Standard MJK REV. DATE REASON FOR REVISION BY CHECKED APPROVAL M&M
DRAWING NO. 4.30
Skirting Clamped Tail End Closure Sheet 1 of 1
0 Revised, Redrawn and Reissued as Standard MJK M&M
REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.31
Skirting Hinged Tail End Closure Sheet 1 of 1
0 Revised, Redrawn and Reissued as GPN M&M
Standard REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.32
Skirting Curtain at Discharge End of Skirting Sheet 1 of 1
0 Revised, Redrawn and Reissued as GPN M&M
Standard REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.33
Skirting Spill Loading Door Sheet 1 of 1
0 Revised, Redrawn and Reissued as GPN M&M
Standard REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.34
Adjustable Bang Board Deflector (For Green Balls and Fine Materials) Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.35
Skirting Lump Spill Barrier Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.36
Skirting for 5 Roll Troughing Garland Idlers Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.37
Skirting and Support for 5-Roll Impact Garland Idlers Sheet 1 of 1
M&M
0 Issued as Design Guide RFT JS REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 4.90
Rubber for Skirting and Scrapers Sheet 1 of 1 SECTION 5 TAKE-UPS
0 Issued as Design Guide DH VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL Gravity Take-Up DRAWING NO. 5.02
Typical Arrangement Vertical Sheet 1 of 1
M&M
0 Issued as Design Guide VTA VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL Gravity Take-Up DRAWING NO. 5.03
Typical Arrangement Inclined Sheet 1 of 1
M&M
0 Issued as Design Guide VTA VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL Gravity Take-Up DRAWING NO. 5.04
Typical Arrangement Horizontal Sheet 1 of 1
M&M
0 Issued as Design Guide FJC ABC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL Gravity Take-Up DRAWING NO. 5.05
Typical Arrangement Tail Pulley Sheet 1 of 1 M&M
0 Issued as Design Guide REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 5.08
Counterweight Materials and Densities Sheet 1 of 1
M&M Material Density Precast Concrete Block 150 lb/cu.ft. Mild Steel Punching or Scrap 220-250 lb/cu.ft. Process Material, such as Iron Ore Refer to Project Design Criteria Steel Plates 490 lb/cu.ft. Grinding Balls 280 lb/cu.ft.
0 Issued as Design Guide DH VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 5.10
Vertical Gravity Take-Up Pulley Carriage
Sheet 1 of 1 M&M
0 Issued as Design Guide DH VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 5.11
0 Issued as Design Guide DH ABC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 5.13
Horizontal or Inclined Gravity Take-Up Pulley Carriage Sheet 1 of 1 M&M
0 Issued as Design Guide DH ABC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 5.14
Horizontal or Inclined Gravity Take-Up Pulley Carriage with Plow Sheet 1 of 1
M&M
0 Issued as Design Guide AM VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 5.20
Screw Take-Up Sheet 1 of 1 M&M
.
0 Issued as Design Guide GD REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 5.21
Motorized Winch Take-Up Assembly Sheet 1 of 1 M&M
Drawing 5.08
COUNTERWEIGHT MATERIALS AND DENSITIES
Density 3 Precast concrete block 150 Mild steel punching or scrap 220-250 Process material, such as iron Refer to project design criteria Steel plates 490 Grinding balls 280
SECTION 6 BELT CLEANERS
6.01 Types of Belt Cleaners 6.02 Types of Belt Cleaners 6.10 Belt Scraper, Spring Loaded 6.11 Belt Scraper, Counterweighted 6.12 Belt Scraper, Spring Loaded 6.13 Belt Scraper, Counterweighted 6.14 Belt Scraper, Rubber Band Loaded 6.15 Belt Scraper, Spring Loaded- Double Blade 6.19 Types of Return Belt Plows 6.20 Return Belt Plow 6.21 Return Belt Plow 6.22 Pellet Plant Conveyor Return Belt Plow 6.30 Vertical Take-Up Pulley Deflector 6.31 Typical Scraper Type Clean-Up Device 6.40 Air Jet Belt Cleaner 6.41 Water Spray Belt Cleaner
0 Dec71 Issued as Design Guide VTA VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 6.01
Types of Belt Cleaners Sheet 1 of 1 M&M
0 Issued as Design Guide VTA VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 6.02
Types of Belt Cleaners Sheet 1 of 1 M&M
0 Issued as Design Guide DFH ABC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 6.10
Belt Scraper Spring Loaded Sheet 1 of 1 M&M
0 Issued as Design Guide DFH ABC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 6.11
Belt Scraper Counterweighted Sheet 1 of 1
M&M
0 Issued as Design Guide VTA ABC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 6.12
Belt Scraper Spring Loaded Sheet 1 of 1 M&M
0 Issued as Design Guide FJC JS REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 6.13
Belt Scraper Counterweighted Sheet 1 of 1 M&M
0 Issued as Design Guide GD REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 6.14
Belt Scraper Rubber Band Loaded Sheet 1 of 1
M&M
0 Issued as Design Guide GD REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 6.15
Belt Scraper Spring Loaded - Double Blade Sheet 1 of 1
M&M
0 Issued as Design Guide VTA VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 6.19
Types of Return Belt Plows Sheet 1 of 1
M&M
0 Issued as Design Guide VTA VTA REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 6.20
Return Belt Plow Sheet 1 of 1
M&M
0 Issued as Design Guide ABC ABC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 6.21
Return Belt Plow Sheet 1 of 1 M&M
0 Issued as Design Guide GD REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 6.22
Pellet Plant Conveyors Return Belt Plow Sheet 1 of 1
M&M
0 Issued as Design Guide ABC ABC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 6.30
Vertical Take-Up Pulley Deflector Sheet 1 of 1
M&M
0 Issued as Design Guide GD REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 6.31
Typical Scraper Type Clean-Up Device Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 6.40
Air Jet Belt Cleaner Sheet 1 of 1
M&M
0 Revised, Redrawn and Reissued as Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 6.41
Water Spray Belt Cleaner Sheet 1 of 1 M&M
SECTION 7 HOODS, SCREENS, GUARDS AND COVERS
7.01 Head Pulley Enclosure for Fig. 2.01 Frame 7.02 Head Pulley Enclosure Fabricated Frame 7.03 Alternate Head Pulley Enclosure for Fig. 2.01 Frame 7.20 Bolted Weather Hood 7.21 Hinged Weather Hood 7.22 Types Of Weather Hoods 7.23 Wind Hoops 7.24 Hinged Weather Hood 7.40 Inspection Door - Dust Tight 7.41 Inspection Door 7.42 Inspection Door
0 Revised, Redrawn and Reissued as Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 7.01
Head Pulley Enclosure for Figure 2.01 Frame Sheet 1 of 1 M&M
0 Revised, Redrawn and Reissued as Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 7.02
Head Pulley Enclosure Fabricated Frame Sheet 1 of 1
0 Revised, Redrawn and Reissued as Standard
REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 7.03 M&M
Alternate Head Pulley Enclosure For Figure 2.01 Frame Sheet 1 of 1
0 Revised, Redrawn and Reissued as Standard GPN REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 7.20 M&M
Bolted Weather Hood Sheet 1 of 1
0 Issued as Design Guide FJC ABC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 7.21 M&M
Hinged Weather Hood Sheet 1 of 1
0 Issued as Design Guide FJC ABC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 7.22 M&M
Types of Weather Hoods Sheet 1 of 1
0 Issued as Design Guide ABC ABC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL M&M
DRAWING NO. 7.23
Wind Hoops Sheet 1 of 1
0 Issued as Design Guide GD DW REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 7.24 M&M
Hinged Weather Hood Sheet 1 of 1
0 Issued as Design Guide DH/ABC ABC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 7.40 M&M
Inspection Door Dust Tight Sheet 1 of 1
0 Issued as Design Guide GD REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 7.41 M&M
Inspection Door Sheet 1 of 1
0 Issued as Design Guide GD REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 7.42 M&M
Inspection Door Sheet 1 of 1
SECTION 9 MISCELLANEOUS
9.01 Pull Cable - Emergency Stop Switch 9.02 Belt Alignment Switch 9.03 Speed Switch at Tail or Bend Pulley 9.05 Belt Rip Protection Device 9.06 Belt Rip Protection Device 9.07 Belt Rip Protection Device 9.08 Belt Rip Protection Device
M&M
0 Issued as Design Guide REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 9.01
Pull Cable Emergency Stop Switch Sheet 1 of 1
M&M
0 Issued as Design Guide AM ABC REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 9.02
Belt Alignment Switch Sheet 1 of 1
M&M
0 Issued as Design Guide REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 9.03
Speed Switch at Tail or Bend Pulley Sheet 1 of 1
M&M
0 Issued as Design Guide GD REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 9.05
Belt Rip Protection Device Sheet 1 of 1
M&M
0 Issued as Design Guide DG REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 9.06
Belt Rip Protection Device Sheet 1 of 1
M&M
0 Issued as Design Guide GD REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 9.07
Belt Rip Protection Device Sheet 1 of 1
M&M
0 Issued as Design Guide GD REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 9.08
Belt Rip Protection Device Sheet 1 of 1
M&M
SECTION 10 ADDENDA
10.001 Dimensional Data for a Concave Curve, 150 ft. Radius 10.002 Dimensional Data for a Concave Curve, 200 ft. Radius 10.003 Dimensional Data for a Concave Curve, 250 ft. Radius 10.004 Dimensional Data for a Concave Curve, 300 ft. Radius 10.005 Dimensional Data for a Concave Curve, 350 ft. Radius 10.006 Dimensional Data for a Concave Curve, 400 ft. Radius 10.007 Dimensional Data for a Concave Curve, 450 ft. Radius 10.008 Dimensional Data for a Concave Curve, 500 ft. Radius 10.009 Dimensional Data for a Concave Curve, 600 ft. Radius 10.010 Dimensional Data for a Concave Curve, 700 ft. Radius 10.011 Dimensional Data for a Concave Curve, 800 ft. Radius 10.012 Dimensional Data for a Concave Curve, 900 ft. Radius 10.013 Dimensional Data for a Concave Curve, 1000 ft. Radius 10.400 Belt Conveyor Carrying Idlers - Metric Standard (J.I.S.) 10.401 Belt Conveyor Return Idler - Metric Standard (J.I.S.)
0 Issued as Design Guide DH RFT REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 10.001
Dimensional Data for a Concave Curve One Tangent Horizontal Sheet 1 of 1 M&M
0 Issued as Design Guide DH RFT REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 10.002
Dimensional Data for a Concave Curve One Tangent Horizontal Sheet 1 of 1
M&M
0 Issued as Design Guide DH RFT REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 10.003
Dimensional Data for a Concave Curve One Tangent Horizontal Sheet 1 of 1
M&M
0 Issued as Design Guide DH RFT REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 10.004
Dimensional Data for a Concave Curve One Tangent Horizontal Sheet 1 of 1
M&M
0 Issued as Design Guide DH RFT REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 10.005
Dimensional Data for a Concave Curve One Tangent Horizontal Sheet 1 of 1
M&M
0 Issued as Design Guide DH RFT REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 10.006
Dimensional Data for a Concave Curve One Tangent Horizontal Sheet 1 of 1
M&M
0 Issued as Design Guide DH RFT REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 10.007
Dimensional Data for a Concave Curve One Tangent Horizontal Sheet 1 of 1
M&M
0 Issued as Design Guide DH RFT REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 10.008
Dimensional Data for a Concave Curve One Tangent Horizontal Sheet 1 of 1
M&M
0 Issued as Design Guide DH RFT REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 10.009
Dimensional Data for a Concave Curve One Tangent Horizontal Sheet 1 of 1
M&M
0 Issued as Design Guide DH RFT REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 10.010
Dimensional Data for a Concave Curve One Tangent Horizontal Sheet 1 of 1
M&M
0 Issued as Design Guide DH RFT REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 10.011
Dimensional Data for a Concave Curve One Tangent Horizontal Sheet 1 of 1
M&M
0 Issued as Design Guide DH RFT REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 10.012
Dimensional Data for a Concave Curve One Tangent Horizontal Sheet 1 of 1
M&M
0 Issued as Design Guide DH RFT REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 10.013
Dimensional Data for a Concave Curve One Tangent Horizontal Sheet 1 of 1
M&M
0 Issued as Design Guide GD DW REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 10.400
Metric Standard (J.I.S.) Belt Conveyor Carrying Idlers Sheet 1 of 1
M&M
0 Issued as Design Guide GD DW REV. DATE REASON FOR REVISION BY CHECKED APPROVAL DRAWING NO. 10.401
Metric Standard (J.I.S.) Belt Conveyor Carrying Idlers Sheet 1 of 1