1 Antenna port to jumper connector properly joined
2 Outer jumper cable have not a sharp bend 3 Outer jumper cable don't have any damage 4 The cable on VCT is straight and perpendiculur to ground 5 The cable on VCT is straight and perpendiculur to ground 6 In Weather proofing PVC tape is applied at the bottom and Butyl tape is less than the PVC tape as applied 7 In Weather proofing PVC tape is applied at the bottom and Butyl tape is less than the PVC tape and Rubber tape is less than butyl tape 8 The PVC layer after Rubber tape is covering all layers 9 Black color cable ties are used 10 Wheather proofing is done opposite the flow of water 11 The feeder male connector and jumper female connector is properly joined 12 Outer insulation of feeder cable is removed properly for earthing kit 13 Bending radius of feeder cable is grater than 300mm 14 Earthing kit's grounding cable is placed in downward direction with no loop 15 Earthing kit's grounding cable is placed in downward direction with no joint 16 Earthing kit is placed all in a single line and 1.5m from jumper-feeder connector 17 Earthing kit is connected by a lug propery 18 Cables on HCT are parallel to ground and perpendicular to VCT 19 WFT is properly sealed 20 Z bend hasn't sharp edges 21 Surge Arrester is properly connected to IGB 22 Feeder connector male to S.A.female connector is connected properly 23 Surge Arrester female connector is properly connected to Jumper male 24 The grounding cable in between Surge Arrester and IGB is 16sq. Mm 25 The grounding cable in between EGB and IGB is 35sq.mm 26 13 number nut & bolt used in connection of lug with a SA 27 EGB is properly connected to Grounding pit. 28 Indoor Jumper cable is not routed with a sharp turn 29 Antenna height is according to RF plan 30 Azimuth plane is according to RF plan 31 RF clamp placed at every 1.5 m on VCT 32 RF clamp placed at every 0.6m on HCT 33 34 35 36 37 38 39 40 41 42 Status Punch Points not ok The port is joined properly but some amount of water drops in it. not ok The loop used here its radius is too small. not ok The jumper male connector is broken. not ok Straight but not perpendiculur to ground not ok Cable is not straight nor perpendiculur to ground not ok The butyl tape is greater than PVC tape not ok The rubber tape is covering butyl tape not ok The PVC tape on top is lesser than rubber tape not ok White color cable ties are used not ok It is made as on the flow of water as aresult water is inside not ok The port is joined properly but dust paticles are there not ok Some outer core is also removed not ok Bending radius is less than 300mm not ok A loop is there on the earthing kit's grounding cable not ok A joint is there in between grounding cable and tower not ok All are not in single line some are at 1.6m some are at 1.4m etc not ok It is not connected properly not ok It is not parallel to ground nor perpendicular to HCT not ok WFT is not properly sealed not ok There is sharp edges on the WFT not ok There is loose connection in between Surge Arrester not ok There cable is loosely connected not ok There connectors are very tightly connected not ok wrong cable used it's of 35sq.mm not ok wrong cable used it's of 16sq.mm not ok 20 number Nut and bolts are used not ok The grounding is not properly maintained not ok There is sharp turn in the routing cable not ok improper coverage not ok wrong coverage area is selected not ok imbalace not symmetric not ok rf clamp is placed at every 0.6m but it is not in proper line
Cable Preparation Guide For Connecting MOTOTRBO Radio As A Control Station To The Radioserver (Using HLN9457 Connector and PMKN4147A Programming Cable)
How Two Boys Made Their Own Electrical Apparatus
Containing Complete Directions for Making All Kinds of Simple Apparatus for the Study of Elementary Electricity