Beruflich Dokumente
Kultur Dokumente
F
0
20
0
100
50
150
150 100 50 200
250
300
350
450
400
300
2
8
5
VALVE SIZE
INCHES mm
Cv (MAX.) AT 90 OPENING
1 25 26
1.1/2 40 78
2 50 120
2.1/2 65 220
3 80 325
4 100 595
6 150 1050
8 200 1750
% VALVE OPENING
70
F
L
O
W
C
O
-
E
F
F
I
C
I
E
N
T
(
C
v
)
U
S
-
G
P
M
0.8
0.6
10
0.4
0.3
0.2
0.1
40 20 30 50 60
80
60
8
6
4
3
2
10
40
30
10
20
600
400
300
200
100
2000
1000
800
V
A
L
V
E
S
I
Z
E
.
V
A
V
L
E
C
v
.
100 80 90
1750
595
325
220
120
78
26
40
25
100
80
65
50
200
150 1050
PNEUCON
MOUNTING DIMENSIONS FOR V-NOTCH BALL VALVE
FACE/FACE
SIZE
ACTUATOR MODEL
150
ANSI
300
ANSI
C/C
H1
H2
H
D
TRAVEL
25 PDS-055 127 165 200 375 65 440 286 28
40 PDS-095 165 190 230 390 90 480 371 38
50 PDS-095 178 216 240 390 90 480 371 38
65 PDS-095 190 241 250 390 90 480 371 38
80 PDS-140 203 283 360 600 150 750 443 57
100 PDS-140 229 305 370 600 150 750 443 57
150 PDS-250 267 403 450 850 250 1100 599 90
200 PDS-250 292 419 450 850 250 1100 599 90
INSTALLATION
The valve should preferably be installed with actuator vertically above or below the valve body. It can be installed
in a horizontal or angled position if actuator is suitably supported. Necessary clearance should be provided above
the actuator to permit servicing.
The flange bolts are to be tightened evenly to avoid placing strain on the body.
The inlet of air pressure regulator (Air set) should be connected to the pneumatic supply line. Supply pressure to
the diaphragm actuator should be either 1.5 kg/cm (20 psig) or 2.5 kg/cm (35 psig) as per indication on the
nameplate. For cylinder actuator, supply pressure specified. For control applications, the air set and valve
positioner are mounted, piped and adjusted at the factory.
Final check
After installation, check the valve operation for full stroke travel as indicated on the nameplate, check for leaks in
air line connection. Open and close the valve two or three times to ensure proper operation. Before commissioning
the process flow, it is essential to flush clean the piping properly.
Ball valves require minimum maintenance for its operation. Apply a few drops of oil on the exposed guides and
bushings, Hand wheel, if present, must be greased periodically.
01/02 PVCT-310-00
Page 3 of 3
D
E
S
I
G
N
E
D
:
B
Y
A
V
I
N
A
S
H
The companys policy is one of continuous product improvement and the right is reserved to modify
the specifications contained herein without notice.
Plot No : A-35, Road No 10, Wagle Industrial Estate, Thane 400 604, India.
Phone : 91-(022) 2583 8371, 2583 8372, 2583 83769, Fax : 91-(022) 2583 8373
Website : www. pneuconvalves.com E-mail : pneucon@vsnl.com
UKAS
QUALITY
MANAGEMENT
P N E U C O N V A L V E S P V T. L T D.
F F C C
H
2
H
1
H
D
SIDE VIEW FRONT VIEW
F
I
L
E
N
A
M
E
-
E
:
\
I
S
O
9
0
0
0
\
C
A
T
L
O
G
\
P
V
C
T
-
3
1
0
-
0
0